User Guide - Teltex, Inc.
Contents
1. Liberto See the illustrations on page 2 for an explanation of the points below e Talk button Used to establish connection with the CIBS Neck Loop e Inlet for charging and accessories The power supply cable accessory is connected here as well as other accessories with 2 5mm jacks e Status lamp Shows if the Liberto is communicating with the CIBS Neck Loop See the table on page 11 for an explanation of the light signals 6 UsermanualCIBSPersonalListener NO_GB_F_D NL ES SE DK SU 1f e Microphone selector Used to switch between the directional and omni directional microphones see explanation below e Battery indicator lamp Shows the battery level of the Liberto See the table on page 11 for an explanation of the light signals e Zoom microphone Captures sound from a defined direction and reduces background noise Omni microphone Captures sound from all directions 360 degrees On Off button Switches device on and off e Microphone sensitivity button Used to adjust the sensitivity strength of the microphones The functions of the CIBS Personal Listener CIBS Personal Listener is a conversation amplifier to use for hearing impaired with or without hearing aids The multi functional and wireless microphone reduces background noise and is useful in conversations in the car in meetings and to listening You will receive amplified sound on your hearing aid with Telecoil hea2. Bluetooth CIBS PERSONAL LISTENER USER MANUAL CIBS Neck Loop Twin Charger Cradle 1 1 1 1 LIBERTO CIBS PERSONAL LISTENER All units in this set are ready paired for your convenience English Congratulations a a a 5 About the CIBS Personal Listener ee 5 CIBS Neck Loop receiver a nerne Twin Charger Cradle a Liberto The functions of the CIBS Personal Listener 7 Charging the CIBS Neck Loop Liberto 7 Installing the Twin Charger Cradle 8 Switch on off the CIBS Neck Loop Liberto 8 Pairing the devices a ener erne 9 SA 10 adjust the volume CIBS Neck Loop 10 adjust the sensitivity strength of the microphone 10 Switch between microphonesS ccccccceceececeeeeceecuceeeuss 10 establish speech connection a 10 terminate connection to the Liberto 11 Description of light diodes and colours 11
3. they will establish communication with each other The status lamp on the Liberto will illuminate solid yellow It will do this every time it communicates with the CIBS Neck Loop e Ifthe pairing is unsuccessful repeat this section UsermanualCIBSPersonalListener NO_GB_F_D NL ES SE DK SU 1f 10 How to o adjust the volume CIBS Neck Loop The volume can be adjusted in stages press for each volume level or by pressing the volume button on the CIBS Neck Loop in the desired direction until the desired volume level has been reached e You will hear a signal when the volume has reached the lowest or highest level e The CIBS Neck Loop remembers its last volume position so that when switched off and on it will start at the same volume position adjust the sensitivity strength of the microphone e The sensitivity strength can be adjusted in stages press for each level or by holding the volume button B on the Liberto in the desired direction until the desired level has been achieved e The Liberto remembers its last volume position so that when it is switched off and on it will start at the same volume position switch between microphones e You can switch between two different microphones The omni directional microphone captures sound from all direc tions The directional microphone captures sound from just one direction and reduces background noise e When using the directional microphone it must be poi
4. Trouble shooting and FAQ 12 Storage and maintenance 12 Certification and safety approvals english B Declaration of conformity english C 4 UsermanualCIBSPersonalListener NO_GB_F_D NL ES SE DK SU 1f Congratulations Congratulations with your new CIBS Personal Listener We hope you get a lot of pleasure from this solution which gives you better sound in conversations and at meetings with several participants This user manual will ensure you get started so that you get the most pleasure from your new solution Your local dealer offers a range of accessories which will further enhance the functionality of this product Before use the units must be fully charged see page 7 for instructions Charge time is approximately 2 hours Be aware When connected to a headset earbuds the CIBS Neck Loop can emit sound of a very high volume Exposure to this may cause permanent hearing damage Be careful when increasing the volume to avoid such injuries Be careful when using the device while engaged in activities which demand your full attention Never attempt to dismantle the product yourself Only approved local dealers or service centres may open the products Contact your local dealer if any parts of the unit need replacing Keep out of reach of children The plastic packaging of the product and accesso
5. that the Bluetooth products to which this declaration refers conforms withthe relevant standards or other standardised documents e 93 42 E F e NS EN 12182 e ETSI EN 301 489 1 V1 4 1 2002 08 e ETSI EN 301 489 17 V1 2 1 2002 08 e EN 300 328 V1 6 1 2004 11 e EN 61000 4 3 5 1 e EN 61000 4 2 5 2 According the regulations in Radio Equipment and Telecommunications Terminal Equipment R amp TTE Directive 1999 5 EC This device complies with Part 15 ofthe FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This device is a class 2 Bluetooth device max 2 mW EIRP Due to the low level of transmit output power the device is not subject to the routine RF exposure valuation as per Section 2 1093 ofthe FCC rules Levanger 2009 04 24 Roar Austvik Er Managirig Director COMMidt UsermanualCIBSPersonalListener NO_GB_F_D_ NL ES SE DK SU 1f
6. the Liberto so that it can be hung around the neck Thread the accompanying cord through the hole on the Liberto s clip Make a loop in the cord so that it remains in place Description of light diodes and colours What you see What this implies for the CIBS Neck Loop Liberto Solid blue light The battery level is between 100 20 Flashing red light The battery level is below 20 Flashing blue light The Liberto is searching for the Liberto CIBS Neck Loop Solid blue light I while charging Charging complete Flashing red light while charging The CIBS Neck Loop Liberto is charging Alternating blue and The CIBS Neck Loop Liberto is ready for red light pairing What you see What this implies for the Liberto i i The Liberto is connected to the Solid yellow light CIBS Neck Loop UsermanualCIBSPersonalListener NO_GB F D NL ES SE DK SU 1f 1 1 EN Trouble shooting and FAQ The CIBS Neck Loop Liberto will not switch on e Charge the battery CIBS Neck Loop Liberto will not charge e Make sure the device is connected correctly to the Twin Charger Cradle during charging e Make sure the power supply is correctly connected to the Twin Charger Cradle and that the plug is working I hear crackling e For the best possible sound quality the CIBS Neck Loop must be within range of the Liberto e If you are using the headset make sure the plug to the headset is securely connected I cannot hear anything from the CIB
7. S Neck Loop e Increase the sound volume of the CIBS Neck Loop e Check that the CIBS Neck Loop is paired with the Liberto e If you are using the headset make sure the plug to the headset is securely connected e If you are using the hearing aid make sure the loop is placed correctly around the neck and that the hearing aid is set to Tor MT Will the CIBS Neck Loop Liberto work with other Bluetooth equipment e The devices are made to work with all Bluetooth devices This depends on the Bluetooth devices being compatible with Bluetooth version 1 1 1 2 or 2 0 that support a headset and have a handsfree and or A2DP profile e The Bluetooth devices must have 0000 as password e The CIBS Neck Loop can only have one device paired to it at any one time Storage and maintenance e Always store the devices in a safe place with the power switched off Do not store the device in extreme temperatures over 45 C 113 F in direct sunlight or below 10 C 14 F This can reduce the lifetime of the battery and affect performance e High temperatures can also reduce performance e Do not expose the devices to rain or other liquids e Clean the devices with a dry cloth 1 2 UsermanualCIBSPersonalListener NO_GB_F_D NL ES SE DK SU 1f Ul gL 7 WW GOL n ul 6b G Ww ZEL 57 mm 2 24 in I I I L 38 mm 1 50 in 310V43 HU39HVHI NIML UsermanualCIBSPers
8. dset at a distance of up to 30 metres with a clear line of sight Charging the CIBS Neck Loop Liberto Make sure the CIBS Neck Loop and Liberto are fully charged before you begin to use them on can charge the CIBS Neck Loop in the following ways With the Twin Charger Cradle e Directly from a computer by USB cable accessory e Through the charger from the power supply accessory e With the Car Charger accessory While charging the Battery indicator lamp on the CIBS Neck Loop on the Liberto will flash red When the CIBS Neck Loop Liberto is fully charged UsermanualCIBSPersonalListener NO_GB_F_D NL ES SE DK SU 1f EN the Battery indicator lamp on the CIBS Neck Loop on the Liberto will illuminate solid blue When the battery level is low the Battery indicator lamp on the CIBS Neck Loop B on the Liberto will flash red and at the same time you will hear a signal from the CIBS Neck Loop To recharge CIBS Neck Loop Liberto without clip in the Twin Charger Cradle you have to push the unit down and out to the side in the charging cradle Push the the unit down and in toward the centre of the charging cradle to remove the device To recharge Liberto with the clip you have to you twist the clip upwards Push the Maestro down in the charging cradle until you hear a click Push the Maestro down and then push the clip towards the Maestro to remove the unit from the Audiostreamer NOTE The lifetime of the battery
9. nted towards the sound source you wish to hear see page 2 to see where the microphones is placed e Switch between the microphones by setting the microphone source B button to the desired position establish speech connection e Establish connection from the CIBS Neck Loop Switch on the Liberto see page 8 for instructions Switch on the CIBS Neck Loop The CIBS Neck Loop will then search for the Liberto The CIBS Neck Loop will establish a connection with the Liberto You will see this when the status lamp on the Liberto illuminates solid yellow e Establish connection from the Liberto Switch on the Liberto see page 8 for instructions Switch on the CIBS Neck Loop Press the talk button The Liberto will search for your CIBS Neck Loop The Liberto will establish a connection with the CIBS Neck Loop You will see this when the status lamp on Liberto illuminates solid yellow UsermanualCIBSPersonalListener NO_GB_F_D NL ES SE DK SU 1f terminate connection to the Liberto EN e The communication can be terminated in the following 3 ways Switch off the CIBS Neck Loop see page 8 for directions Press the talk button on the Liberto Switch off the Liberto see page 8 for instructions Useful tips Using the accompanying rotating shirt blouse clip can reduce noise caused by the device rubbing off clothing Attach the clip to the back of the Liberto You can also attach a cord to the clip on
10. onalListener NO GB F D NL ES SE DK SUJ1f Certification and safety approvals CE This product is CE marked accordingly to the provisions of the R amp TTE Directive 99 55 EC COMMidt AS declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1995 5 EC For further information please consult http www commidt com Bluetooth The Bluetooth word and logos are owned by the Bluetooth SIG Inc and any use of such marks by COMMidt AS is under licence Other trademarks and trade names are those of their respective owners Electrical and electronic equipment EEE contains materials components and substances which can be dangerous and detrimental to human health and the environment if waste electrical and electronic equipment WEEE is not disposed of correctly Products marked with the crossed out waste bin BEE symbol shown below are electrical and electronic equipment This symbol indicates that waste electrical and electronic equipment must not be discarded along with unsorted household waste but must be collected separately In the development and manufacture of your COMMidt product high quality materials and components have been used which can be recycled When disposing of electrical and electronic equipment you should therefore make use of a collection arrangement intended for this purpose which may involve either delivery at your local collection point or recycling
11. ries are not children s toys The packaging or the small parts it contains may cause choking if swallowed Ignition of flammable atmospheres Do not use the devices in environments where there is a danger of igniting flammable gasses About the CIBS Personal Listener The CIBS Personal Listener consists of 3 devices CIBS Neck Loop Liberto wireless microphone and the Twin Charger Cradle The CIBS Neck Loop receives sound from Liberto UsermanualCIBSPersonalListener NO_GB_F_D NL ES SE DK SU 1f EN CIBS Neck Loop receiver See the illustrations on page 1 for an explanation of the points below e Volume button Push upwards for higher volume and downward for lower volume e On Off button Switches device on and off e Inlet for charging and accessories The cable from the power outlet accessory is connected here e USB socket Used for charging the device via USB cable to a computer accessory Pairing button Sets the CIBS Neck Loop to pairing mode e Headset socket Can be connected to the accompanying headset or a standard headset e Battery indicator lamp Y Shows the battery level of the CIBS Neck Loop See the table on page 11 for an explanation of the light signals Twin Charger Cradle See the illustrations on page 1 for an explanation of the points below e Charge cradle For charging CIBS Neck Loop and Liberto e Power socket The accompanying power supply is connected here
12. rto and at the same time you will hear a signal via the T Loop or via the connected headset on the CIBS Neck Loop How to switch off the CIBS Neck Loop Liberto e Press and hold in the On Off button on the CIBS Neck Loop on the Liberto until you see a red light on the Battery indicator lamp on the CIBS Neck Loop on the Liberto and at the same time you will hear a signal via the T Loop or via the connected headset on the CIBS Neck Loop Pairing the devices The devices in the CIBS Personal Listener must be programmed to communicate with each other This is done by connecting them wirelessly pairing NOTE It is important that the CIBS Neck Loop and the Liberto are within a distance of 1 meter during pairing and that both devices are fully charged Both units of the CIBS Personal Listener CIBS Neck Loop and Liberto are ready paired If any difficulties arise such as the pairing is deleted you can use the instructions below e Switch on the CIBS Neck Loop see page 8 for instructions e Press and hold in the pairing button on the CIBS Neck Loop until the Battery indicator lamp on the CIBS Neck Loop flashes alternately red and blue At the same time you should hear a double tone via the T Loop or via the headset on the CIBS Neck Loop e Pressand hold in the On Off button on the Liberto until the Battery indicator lamp on the Liberto flashes alternately red and blue e Whenthe CIBS Neck Loop and Liberto are paired
13. station or collection at your home Further information should be obtained from your local dealer Batteries contain substances that may be harmful to human health and the environment if not handled properly Batteries are labelled with a crossed dustbin as shown It symbolizes that waste batteries must not be disposed of as unsorted municipal waste but must be collected separately Some batteries are also labelled with the chemical symbol Hg mercury Cd cadmium or Pbllead This is particularly harmful substances and therefore it is important that these batteries will be collected It is important that you hand your waste batteries to the collection systems which are established On this way you help to ensure that batteries are recycled in accordance with the law and will not unduly impact the environment When disposing of waste batteries you must use a collection system established for that purpose whether it be handed in at your local collection point or recycling or collected directly from the household Detailed information must be obtained from the local authorities UsermanualCIBSPersonalListener NO_GB_F_D NL ES SE DK SU 1f Removal of the battery Unscrew the screw on the rear of the unit Remove the front cover Unscrew the screw on the circuit board Remove the circuit board Unplug the battery QI Ps OO IS Declaration of conformity We COMMidt Kirkegata 57 59 7600 Levanger Norway declare under our own responsibility
14. will be significantly reduced if the device is left uncharged for extended periods We advise you to charge the device at least once a month When the operating time of the battery begins to decrease and you wish to replace it please send it to your local dealer The article number of the battery is 956 001 Installing the Twin Charger Cradle Connect the accompanying power supply to the power socket The Twin Charger Cradle will switch itself on automatically You will not be able to see this unless you place the CIBS Neck Loop Liberto into the charger and ensure they are charging The Charger Cradle has no on off button and will not use power as long as you don t charge anything in it A removable device is included that allows you to charge CIBS products both with and without clips in the charging cradle If you wish to charge CIBS products without clips this must be placed down in the charging station as shown in the picture together with the assembly instructions on page A If you would like to place the Twin Charger Cradle on the wall you can use the accompanying brackets Assembly instructions on page A Switch on off the CIBS Neck Loop Liberto How to switch on the CIBS Neck Loop Liberto e Press and hold in the On Off button on the CIBS Neck Loop 8 UsermanualCIBSPersonalListener NO_GB F D NL ES SE DK SU 1f on the Liberto until you see a blue light on the Battery indicator lamp on the CIBS Neck Loop B on the Libe
Download Pdf Manuals
Related Search