User manual Dishwasher
Contents
1. 4 User manual o Doa 4 g 4 Dishwasher lt PN 4 IDSH451W Contents Safety instructions _ _ 2 Product description 3 Control panel 3 Programmes 4 4 5 Options _ _ _ Before first use A Safety instructions Before the installation and use of the appliance careful ly read the supplied instructions The manufacturer is not responsible if an incorrect installation and use cau ses injuries and damages Always keep the instructions with the appliance for future reference Children and vulnerable people safety Warning Risk of suffocation injury or permanent disability Do not let persons children included with reduced physical sensory reduced mental functions or lack of experience and knowledge use the appliance They must have supervision or instruction for the operation of the appliance by a person who is responsible for their safety Do not let children play with the appliance Keep all packaging away from children Keep all detergents away from children Keep children and pets away from the appliance door when it is open Installation e Remove all the packaging Do not install or use a damaged appliance Do not install or use the appliance where the temper ature is less than 0 C Obey the installation instruction supplied with the ap pliance Make sure that the appliance is installed below an2. Customer Care Please contact Electrolux Major Appliances Addington Way Luton Bedfordshire LU4 9QQ Contact No 08445 613613 13 14 15 117908310 A 182013 neue CE
3. re fer to Setting and starting a programme Ifthe salt indicator is on fill the salt container 3 Load the baskets 4 Add the detergent 5 Set and start the correct programme for the type of load and the degree of soil Using the detergent Ifthe programme has a prewash phase put a small quantity of deter gent on the inner part of the appliance door Using the combi detergent tablets When you use tablets that contain salt and rinse aid do not fill the salt container and the rinse aid dispenser 1 Adjust the water softener to the lowest level 2 Set the rinse aid dispenser to the lowest position If you stop to use the combi detergent tablets before you start to use separately detergent rinse aid and dishwasher salt do these steps 1 Press the on off button to activate the appliance 2 Set the water softener to the highest level 3 Make sure that the salt container and the rinse aid dispenser are full 4 Start the shortest programme with a rinsing phase without detergent and without dishes 5 Adjust the water softener to the water hardness in your area 6 Adjust the released quantity of rinse aid Setting and starting a programme Setting mode For some settings it is necessary that the appliance is in setting mode The appliance is in setting mode when all the pro gramme indicators are off and the end indicator flashes Hints and tips The water softe
4. the spray arms Do not remove the spray arms If the holes in the spray arms are clogged remove re maining parts of soil with a thin pointed object External cleaning Clean the appliance with a moist soft cloth Only use neutral detergents Do not use abrasive prod ucts abrasive cleaning pads or solvents To remove filters B and Remove filter A Wash C turn the handle coun the filter with water terclockwise and remove Internal cleaning Pull apart filter B and If you regularly use short duration programmes these C Wash the filters with can leave deposits of grease and limescale inside the water appliance To prevent this we recommend to run long duration pro grammes at least 2 times per month Before you put the filter Assemble filters B and A back make sure that C Put them back in fil there are no residues of ter A Turn the handle food or soil in or around clockwise until it locks the edge of the sump Make sure that filter A is correctly positioned under the 2 guides D Troubleshooting The appliance does not start or it stops during opera With some problems different indicators flash con tion tinuously or intermittently at the same time to show Before you contact the Service refer to the information an alarm code that follows for a solution to the problem s The indicator of the set programme flashes continu The appliance does not fill with water ous
5. amme for test institutes 3 With this programme you can wash a load with fresh soil It gives good washing results in a short time 4 Use this programme to quickly rinse the dishes This prevents the remaining food to bond on the dishes and bad odours to come out from the appliance Do not use detergent with this programme Information for test institutes For all the necessary information for test performance send an email to info test dishwasher production com Write down the product number PNC that is on the rating plate Options Acoustic signals By default the acoustic signals are on but it is possible The acoustic signals operate when the programme is to deactivate them completed and when the appliance has a malfunction How to deactivate the acoustic signals 1 Press the on off button to activate the appliance Make sure that the appliance is in setting mode re fer to Setting and starting a programme Press the programme button The end indicator goes off The acoustic signals are off Press the on off button to deactivate the appliance 2 Press and hold the programme button until the indi and to confirm the setting cator ECO 50 flashes and the indicator How to activate again the acoustic signals Y 65 Ra on 1 Refer to How to deactivate the acoustic signals 3 Press immediately the programme button and follow the procedure from step 1 to step 5 The indicator ECO 50 comes o
6. basket then from the upper basket There can be water on the sides and on the door of the appliance Stainless steel becomes cool more quickly than the dishes The dishwasher salt keeps the water softener clean and in good conditions It is important to set the right level of the water softener This makes sure that the water soft ener uses the correct quantity of dishwasher salt and water Using salt rinse aid and detergent Only use salt rinse aid and detergent for dishwasher Other products can cause damage to the appliance The rinse aid helps during the last rinsing phase to dry the dishes without streaks and stains Combi detergent tablets contain detergent rinse aid and other added agents Be sure that these tablets are applicable to the water hardness in your area Refer to the instructions on the packaging of the products Detergent tablets do not fully dissolve with short pro grammes To prevent detergent residues on the ta bleware we recommend that you use the tablets with long programmes Do not use more than the correct quantity of deter gent Refer to the instructions on the detergent packaging Loading the baskets Refer to the supplied leaflet with examples of the load of the baskets Only use the appliance to wash items that are dish washer safe Do not put in the appliance items made of wood hom aluminium pewter and copper Do not put in the appliance items that can abs
7. d adjacent to safe structures Electrical connection A Warning Risk of fire and electrical shock The appliance must be earthed Daily use ___ A eh ee Hints and tips 8 Care and cleaning__________________9 Troubleshooting 10 Technical information es __ 12 Environment concerns 12 Subject to change without notice Make sure that the electrical information on the rating plate agrees with the power supply If not contact an electrician Always use a correctly installed shockproof socket Do not use multi plug adapters and extension cables Make sure not to cause damage to the mains plug and to the mains cable Should the appliance power supply cable need to be replaced this must be car ried out by our Service Centre Connect the mains plug to the mains socket only at the end of the installation Make sure that there is ac cess to the mains plug after the installation Do not pull the mains cable to disconnect the appli ance Always pull the mains plug Do not touch the mains cable or the mains plug with wet hands Only for UK and Ireland The appliance has a 13 amp mains plug If itis necessary to change the fuse in the mains plug use a 13 amp ASTA BS 1362 fuse This appliance complies with the E E C Directives Water connection Make sure not to cause damage to the water hoses The appliance is to be connected to the water mains using the new supplied hose sets Old h
8. it Help protect the environment and human health and to recycle waste of electrical and electronic appliances Do not dispose appliances marked with the symbol amp with the household waste Return the product to your local recycling facility or contact your municipal office Discard correctly the packaging material Recycle the materials with the symbol 4 GREAT BRITAIN Customer Care and Service Standard Guarantee Conditions and Exclusions All our products come with 12 month warranty To see our guarantee conditions and exclusions please visit our Customer Care Department www benchmarxjoinery co uk Service and Spare Parts Service is provided by Electrolux Major Appliances as authorised service partner network Please contact your local Service Centre on 08445 616616 Your call will automatically be routed to your local centre Please ensure you read all information under Troubleshooting in your instruction booklet before contacting us for service Servicing and or installation of your product should be carried out by a suitably qualified engineer In the user manual you will find some useful information on how to 12 deal with minor faults and how to take care of your product When contacting us for Service please ensure that you have proof of purchase and the following information available Model Naci ne Product NO esta roda Sea NO a css ses 5 15 neigh drones Date of Purchase
9. ly The end indicator flashes 1 time intermittently 10 The indicator of the set programme flashes continu ously The end indicator flashes 2 times intermittently The indicator of the set programme flashes continu ously The end indicator flashes 3 times intermittently Warning Deactivate the appliance before you do the checks The appliance does not drain the water The anti flood device is on You cannot activate the appliance Make sure that the mains plug is connected to the mains socket Make sure that there is not a damaged fuse in the fuse box The programme does not start The appliance does not fill with water Make sure that the appliance door is closed Make sure that the water tap is open Make sure that the pressure of the water supply is not too low For this information contact your local water authority Make sure that the water tap is not clogged Make sure that the filter in the inlet hose is not clogged Make sure that the inlet hose has no kinks or bends The appliance does not drain the water Make sure that the sink spigot is not clogged Make sure that the drain hose has no kinks or bends The anti flood device is on After the checks are completed activate the appliance The programme continues from the point of interruption If the problem occurs again contact the Service If other alarm codes appear contact the Service If the washing and drying results a
10. n with a The end indicator is off fixed light 2 Press the programme button The end indicator The indicator CP 65 starts to flash comes on 4 Wait until the indicator ECO 50 goes off and The acoustic signals are on the end indicator comes on the indicator 3 Press the on off button to deactivate the appliance 65 continues to flash and to confirm the setting The acoustic signals are on Before first use 1 Make sure that the set level of the water softener 4 Open the water tap agrees with the water hardness in your area If not 5 Processing residues can stay in the appliance Start adjust the water softener Contact your local water a programme to remove them Do not use detergent authority to know the water hardness in your area and do not load the baskets 2 Fill the salt container 3 Fill the rinse aid dispenser Adjusting the water softener Water hardness French mmol l degrees fH German degrees dH 11 14 19 25 1 9 2 5 4 10 7 18 0 7 1 8 Water softener adjustment Clarke Level degrees 13 17 3 5 12 2 Water hardness German French mmol l degrees degrees dH lu lt 4 lt 7 lt 0 7 1 Factory position 2 Do not use salt at this level How to adjust the level of the water softener dl Press the on off button to activate the appliance Make sure that the appliance is in setting mode re fer to Setting and starting a programme Press and hold the programme b
11. ner Hard water contains a high quantity of minerals that can cause damage to the appliance and bad washing re sults The water softener neutralises these minerals 8 1 To set the appliance in setting mode press and hold the programme button until all the programme indicators go off and the end indicator flashes Starting a programme 1 Open the water tap 2 Press the on off button to activate the appliance Make sure that the appliance is in setting mode 3 Press continuously the programme button until the indicator of the programme you want to set comes on 4 Close the appliance door The programme starts Opening the door while the appliance operates If you open the door the appliance stops When you close the door the appliance continues from the point of interruption Cancelling the programme 1 Open the appliance door 2 Press and hold the programme button until the indi cator of the set programme goes off and the end in dicator flashes Make sure that there is detergent in the detergent dispenser before you start a new programme At the end of the programme When the programme is completed an intermittent acoustic signal operates and the end indicator is on 1 Press the on off button to deactivate the appliance 2 Close the water tap Important Let the dishes become cold before you remove them from the appliance Hot dishes can be easily dam aged First remove the items from the lower
12. orb wa ter sponges household cloths Care and cleaning Warning Before maintenance deactivate the appliance and disconnect the mains plug from the mains socket Dirty filters and clogged spray arms decrease the washing results Make a check regularly and if necessary clean them Remove remaining food from the items To remove easily remaining burned food soak pots and pans in water before you put them in the appli ance Put hollow items cups glasses and pans with the opening down Make sure that cutlery and dishes do not bond to gether Mix spoons with other cutlery Make sure that glasses do not touch other glasses Put the small items in the cutlery basket e Put the light items in the upper basket Make sure that they do not move Make sure that the spray arms can move freely be fore you start a programme Before starting a programme Make sure that The filters are clean and correctly installed The spray arms are not clogged The position of the items in the baskets is correct The programme is applicable for the type of load and for the degree of soil The correct quantity of detergent is used There is dishwasher salt and rinse aid unless you use combi detergent tablets The cap of the salt container is tight Cleaning the filters An incorrect position of the filters can cause bad washing results and damage to the appliance Cleaning
13. ose sets must not be reused Before you connect the appliance to new pipes or pipes not used for a long time let the water flow until it is clean The first time you use the appliance make sure that there is no leakage Use This appliance is intended to be used in household and similar applications such as Staff kitchen areas in shops offices and other working environments Farm houses By clients in hotels motels and other residential type environments Bed and breakfast type environments Warning Risk of injury burns electrical shock or fire Do not change the specification of this appliance Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal posi tion Do not keep the appliance door open without supervi sion to prevent to fall on it Do not sit or stand on the open door Product description Control panel Dishwasher detergents are dangerous Obey the safety instructions on the detergent packaging Do not drink and play with the water in the appliance Do not remove the dishes from the appliance until the programme is completed There can be detergent on the dishes The appliance can release hot steam if you open the door while a programme operates Do not put flammable products or items that are wet with flammable products in near or on the appliance Do not use water spray and steam to clean the appli ance Dispo
14. re not satisfactory Whitish streaks or bluish layers on glasses and dishes The released quantity of rinse aid is too much Adjust the rinse aid selector to a lower position The quantity of detergent is too much Stains and dry water drops on glasses and dishes The released quantity of rinse aid is not sufficient Adjust the rinse aid selector to a higher position Close the water tap and contact the Service The quality of the detergent can be the cause Dishes are wet The programme is without a drying phase or with a low temperature drying phase The rinse aid dispenser is empty The quality of the rinse aid can be the cause i Refer to HINTS AND TIPS for other possible cau ses 11 Technical information Dimensions Width Height Depth mm 446 818 898 550 Electrical connection Refer to the rating plate Voltage 220 240 V Frequency 50 Hz Water supply pressure Min max bar MPa 0 5 0 05 8 0 8 Water supply Cold water or hot water max 60 C Capacity Place settings 9 Power consumption Left on mode 0 99 W Off mode 0 10W 1 Connect the water inlet hose to a water tap with a 3 4 thread 2 If the hot water comes from alternative sources of energy e g solar panels aeolian energy use the hot water supply to decrease energy consumption Environment concerns Recycle the materials with the symbol amp Put the packaging in applicable containers to recycle
15. sal IN Warning Risk of injury or suffocation Disconnect the appliance from the mains supply Cut off the mains cable and discard it Remove the door catch to prevent children and pets to get closed in the appliance Lower spray arm Filters Rating plate Rinse aid dispenser Detergent dispenser a Salt container Airvent upperspray arm E Upper basket A O1 ote oD os of oS RESET 3 SEC CE On off button Programme indicators Indicators Programme button MC EE gt End indicator S Salt indicator This indicator is off while the programme operates Programmes Programme Degree of soil Programme Duration Energy Water Type of load phases m kWh 0 ECO 5022 Normal soil Prewash 0 86 13 Crockery and cutlery Wash 50 C Rinses Dry O 65 Normal soil Wash 65 C 105 115 1 6 1 9 18 20 Crockery and cutlery Rinses Dry i a Heavy soil Prewash 130 140 1 9 2 1 18 20 70 Crockery cutlery Wash 70 C pots and pans Rinses Dry INF ase 3 Fresh soil Wash 65 C 30 0 8 9 Crockery and cutlery Rinse AD 4 All Prewash 12 0 1 5 1 The pressure and the temperature of the water the variations of the mains supply the options and the quantity of dishes can change the programme duration and the consumption values 2 With this programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil This is the standard progr
16. utton until the indi cator ECO 50 starts to flash and the indica tor CP 65 comes on Wait until the indicator CP 65 goes off and the end indicator starts to flash the indicator ECO 50 continues to flash Press the programme button The end indicator flashes intermittently The number of flashes shows the current level of the water softener e g 5 flashes pause 5 flash es level 5 To adjust the level of the water softener press the programme button Each time you press the pro gramme button you go to the next level Press the on off button to deactivate the appliance and to confirm the setting Filling the salt container Caution Water and salt can come out from the salt container when you fill it Risk of corrosion To prevent it after you fill the salt container start a programme Water softener adjustment Clarke Level degrees lt 5 12 Put 1 litre of water in the salt container only for the first time Filling the rinse aid dispenser se gt lt ZNI Fill the rinse aid dispens To adjust the released er when the lens A is quantity of rinse aid turn clear the selector between po sition 1 lowest quantity and position 4 highest quantity Daily use 1 Open the water tap 2 Press the on off button to activate the appliance Make sure that the appliance is in setting mode
Download Pdf Manuals
Related Search