Home

TerraSync Software Getting Started Guide

1. Flashing Poor satellite geometry PDOP or Poor satellite geometry HDOP Note The message that appears depends on whether a maximum PDOP or HDOP value is configured Flashing satellite Too few satellites count 71cm Solid Estimated accuracy in the field and estimated accuracy after Pac postprocessing Flashing The estimated accuracy value flashes if the required accuracy set in the Accuracy Settings form is not met amp Animated Attempting to connect to GPS receiver 7 Flashing No GPS detected Check cables and batteries Flashing Antenna is not connected to GPS receiver YKE Solid Applying real time corrections from external source Flashing Waiting for real time corrections yee Solid Applying real time corrections from VRS R Flashing Waiting for real time corrections 7 Solid Applying RTK corrections from an external RTK source Be Flashing Waiting for RTK corrections Solid Applying RTK corrections from a VRS LA Flashing Waiting for RTK corrections payee Solid Applying real time corrections from the external beacon receiver ey Flashing Waiting for real time corrections Pg Solid Applying real time corrections from the receiver s integrated beacon differential receiver Flashing Waiting for real time corrections yee Solid Applying real time corrections from the receiver s integrated OmniSTAR receiver Flashing Waiting for real time corrections vee Solid Applying real time corrections
2. a Tap the Setup button Ea beside the Choice xR field The External Source Settings form Psat appears b From the Correction Datum field select the _ Ptema Source os same datum as the VRS network coordinate mae Correction Datum system WGS 1984 i c From the Type field select VRS Type VRS 7 C tion Method Direct Dial d From the Connection Method field select eS Modem Type Direct Dial Bluetooth e From the Modem Type field select the modem that you want to use Then tap the Setup button Ea to open the Connection Properties form f Specify appropriate port connection settings For detailed connection information refer to the documentation for the cellular phone or modem g Ifthe call is authenticated with a username and password select the Use terminal window after dialing check box h Tap OK to return to the External Source Settings form i From the Phone Number field enter the telephone number of the VRS network including any prefix or area code required j From the Connection Control field select Auto to automatically connect to and disconnect from the VRS network as necessary Select Manual to only connect or disconnect when you tap Options in the Setup screen k Tap OK to confirm the settings and return to the Real time Settings form 6 Tap OK Connecting to the VRS network using a direct dial connection To connect to the VRS network using the d
3. 8 Get ready to walk beside the fence and then tap Log to begin For good accuracy you must remain four meters from the fence while logging 9 Once you have logged sufficient GPS positions and have recorded the attributes for the fence tap OK to save the feature and return to the Collect Features screen TerraSync Software Getting Started Guide 115 5 Tutorial Collecting Data Collecting a point feature that you cannot get close to complex ottset You want to record data for a tree but there is no GPS signal under the tree canopy To log a position for the tree you must record three GPS reference positions and then use a tape measure to measure the distance from each reference position to the tree To record a complex point offset 1 Inthe Collect Features screen tap the Tree feature and then tap Create 2 Inthe attribute entry form tap Options and then select Offset The Point Offset pull out list appears 3 From the Point Offset pullout list select Triple Distance 4 The Triple Distance Offset form appears The top sE TerraSync ex of the form has instructions to help you record the feature 5 Move to the location of the first reference position a Tap Log to begin logging Remain stationary at the reference position while you log GPS positions Reference position 1 Not started b When you have collected sufficient positions tap Next to stop logging c Measure the offset This is
4. The required accuracy specified in the Accuracy Settings form has been lost Customizing sounds The TerraSync software is supplied with default sounds for all warning and success events However you can customize these sounds or disable any or all of the sounds played by the software To enable or disable all sounds as a group 1 Tap EQ Settings Personal Sounds and Notifications 2 From the Enable sounds for group select or clear the Applications check box to enable or disable warning and success sounds 3 Select or clear the Events check box to enable or disable sounds for questions and error messages in the TerraSync software X Tip All the sounds used in the TerraSync software are wave wav files A default wav file is supplied for each warning or success event that occurs in the software To change any of the sounds used replace the appropriate wav file in the Windows folder on the field computer To disable a sound delete or rename its wav file TerraSync Software Getting Started Guide User Interface and Data Entry 3 The events and their corresponding sound wav files are as follows Event Feature stored Dead GPS battery Low GPS battery GPS connected GPS OK Poor geometry Position logged Position snapped Real time lost Real time OK Carrier lock acquired Carrier lock lost Required accuracy lost Minimum positions stored Navigation proximity alarm Too Few Satellites
5. Enhanced support for adding image files as attributes to features Integration with CoPilot Live 7 Professional for Trimble TerraSync and TomTom Navigator 6 turn by turn navigation software This chapter contains detailed information about using advanced datalogging options These options enable you to gain more accurate amd time saving results in the field TerraSync Software Getting Started Guide 173 A Advanced Datalogging Options Log Now and Log Later Advanced data collection methods offer time saving techniques for efficient field work The TerraSync software provides two closely related options for logging GPS data These options differ in their timing of GPS data collection relative to the start of a feature The options are e Log Now start a feature and simultaneously start collecting GPS positions e Log Later start a feature and start collecting GPS positions later If you select the Log Now option the TerraSync software begins logging positions for a new feature as soon as you select the feature type and tap Create You can enter attribute values while positions are being recorded Log Now is the default logging option When Log Now is selected a bullet appears beside it in the option list To select Log Now tap Options in the Collect Features screen and then select Log Now from the option list Note Log Now applies only to new features When you open an existing feature for update logging is
6. GETTING STARTED GUIDE TerraSync software Trimble GETTING STARTED GUIDE TerraSync software Version 4 10 Revision A December 2009 Trimble Trimble Navigation Limited 10355 Westmoor Drive Suite 100 Westminster CO 80021 USA www trimble com Legal Notices Copyright and Trademarks 2000 2009 Trimble Navigation Limited All rights reserved Portions of the software are copyright 1995 2008 LizardTech Inc All rights reserved MrSID is protected by U S Patent No 5 710 835 Foreign Patents Pending For STL support the software uses the Moscow Center for SPARC Technology adaptation of the SGI Standard Template Library Copyright 1994 Hewlett Packard Company Copyright 1996 1997 Silicon Graphics Computer Systems Inc Copyright 1997 Moscow Center for SPARC Technology Trimble the Globe amp Triangle logo GeoExplorer and GPS Pathfinder are trademarks of Trimble Navigation Limited registered in the United States and in other countries GeoBeacon GeoXH GeoXM GeoXT GPS Analyst H Star Juno ProXH ProXT TerraSync and VRS are trademarks of Trimble Navigation Limited Nomad Ranger and Recon are either registered trademarks or trademarks of Tripod Data Systems Inc MrSID and LizardTech are trademarks of LizardTech Inc and are used with permission Microsoft ActiveSync Windows Windows Mobile and Windows Vista are either registered trademarks or trademarks of Microso
7. O do not have an Installation Code want to register my copy over the Internet now 9 Doone of the following Ifyou have registered the software and obtained your installation code for the software select the J have already registered option and then click Next Ifyou have not yet registered the software and do not have an installation code for the software select the J do not have an installation code I want to register my copy over the Internet now option and then click Next The Register page opens in your default Web browser displaying the My Trimble account log in For more information see Registering the TerraSync software page 19 The Enter your Installation Code page appears TerraSync 4 10 for Windows Mobile InstallShield Wizard Enter your Installation Code Please enter the Installation Code to install the software 9971 49 00110 10268 944F 452 10 Enter the installation code assigned to your copy of the TerraSync software when you registered the software and then click Next TerraSync Software Getting Started Guide 33 2 34 Software Installation and Activation IL 12 13 The Tutorial page recommends that you complete the tutorial in Chapter 4 of this guide before using the software Click Next The Start Copying Files page appears Click Next If prompted Install Trimble TerraSync using the default application install directory click Yes If the device is
8. To record a point feature L If the Collect Features screen is not already open a Tap the Section list button and then select Data b Tap the Subsection list button and then select Collect Features By default the TerraSync software begins logging GPS positions as soon as you open a new feature To make sure that the default logging option is selected tap Options and then select Log Now Move close to the sign From the Choose Feature list select Traffic Sign and then tap Create The attribute entry form for the Traffic Sign feature type appears Note GPS position logging starts immediately so try to keep the antenna still during these next steps As the software logs GPS positions the counter eS Logging icon beside the logging icon increments see the ot illustration to the right Terrasyne PR The Date Visited attribute is set to auto generate on creation so today s date is automatically filled 4Traffic Sign out You do not need to enter a value in this field pate visited From the list of options in the Type field select a l x Stop These options are the values defined inthe Image file data dictionary Liel This is a new sign so its condition is good From the list of options in the Condition field select Good For information about how to add image file attributes see page 185 You have now recorded all the
9. Use either Microsoft ActiveSync technology or the Windows Mobile Device Center to manage the connection between the device and the computer The software you use depends on the operating system the office computer is running When the device and the computer are connected one of the following appears on the office computer Ifthe computer is running the Windows Vista operating system the Windows Mobile Device Center window appears and displays the message Connected For more information refer to the Windows Mobile Device Center Help Ifthe computer is running the Windows XP or 2000 operating system the Synchronization Setup Wizard appears For more information refer to the ActiveSync Help In the GPS Pathfinder Office software select Data Transfer from the Utilities menu The Data Transfer dialog appears TerraSync Software Getting Started Guide Tutorial Collecting Data 5 From the Device list select the appropriate device GIS Datalogger on Windows Mobile GIS Datalogger on Windows PC or GIS Folder if the TerraSync and GPS Pathfinder Office software are running on the same computer Alternatively if you have set up a device definition for the field computer select that device name from the list The Trimble Data Transfer utility automatically connects to the field computer Select the Receive tab Click Add and then select Data File from the drop down list The Open dialog appears Note The files that app
10. 7 Ifcoordinate systems or sites in the selected export file reference other files such as geoid grid files the Associated Files dialog appears Select the appropriate check box to send each file required and then click OK The selected coordinate system export file and any associated files are transferred to the field computer replacing any coordinate systems stored in the TerraSync software For more information refer to the GPS Pathfinder Office Software Online Help 194 TerraSync Software Getting Started Guide Coordinate Systems B Transferring a single coordinate system A CAUTION To prevent the loss of coordinate system information in the TerraSync software Trimble strongly recommends that you transfer coordinate systems to the field device in a coordinate system export file This is preferable to selecting and sending a single coordinate system Use the Trimble Data Transfer utility to transfer a single coordinate system to the TerraSync software To transfer a coordinate system 1 Connect the field device to the office computer start the Data Transfer utility and connect to the appropriate device definition For detailed instructions see the TerraSync Software Getting Started Guide 2 Select the Send tab 3 Click Add and select Coordinate System from the drop down list The Coordinate System dialog appears Coordinate System a Select By Coordinate System and Zone F Cancel Help Syste
11. Positions 0 Length 2D 3D Name 1 Condition 139 5 140 Tutorial Collecting Data Selecting a target in the Data section Now that you have filtered the list of features you have easily found the feature you must update in the list of existing features To find the feature itself you must navigate to it To navigate to a feature you must select it as your target To select a target 1 Inthe Update Features screen select the filtered road sign 2 Tap Options select Set Nav Target and then select 5 a File Starfis m Point Position from the pullout menu Giog Feature The target icon 9 appears beside the selected feature This icon replaces the icon usually used for the feature Positions 0 Type Condition D Navigating to a target in the Navigation section 1 To open the Navigation section tap the Section list button and then select Navigation The Direction Dial screen appears 2 Use the information in the Direction Dial screen to navigate to the selected target Target name Lightbar Turn arrow indicating direction to target bearing to go Start moving __ Message line Dist 117 10 m Bear 195 T Turn 61 Head 138 T This screen displays all the information that you need to navigate to the target The information fields at the bottom of the screen show different types of navigational informati
12. This may require a test run around or along an object to make sure that you can remain a consistent distance from it Note You can record a line feature as a series of joined line segments each with a different offset See also Segmenting line features page 183 Offsets are added to GPS and digitized positions as they are recorded and features are displayed in the Map section with their offsets However if the currently open line or area feature has an offset acute angles and corners can appear distorted on the map This is because exact offset values are not calculated for these positions until the feature is closed When you close a feature offsets for these positions are interpolated and the feature is redrawn more accurately Area shown on map including offset Actual area traveled excluding offset Open feature Closed feature TerraSync Software Getting Started Guide 177 A Advanced Datalogging Options 178 To record an offset for a feature 1 Start the feature 2 Inthe attribute entry form tap Options and then metoo rence select Offset Direction 3 Ifthe current feature is a point feature select the Horiontal distance type of offset you want to record Then tap OK Neracal distance The appropriate offset form appears The fields on the offset form depend on the type of feature you are collecting point line or area and the type of offset you are
13. change the mode in the current section When you tap a list button a drop down list appears Select an option on the list to access the command it describes The label of the list button changes to match the option you selected The following list buttons appear in the TerraSync software e Section button e Subsection button e Map Tools button in the Map section Status Mode button in the Status section TerraSync Software Getting Started Guide 65 3 66 User Interface and Data Entry Note List buttons differ from menu buttons such as Options buttons in their appearance behavior and function See also Menu buttons page 66 Menu buttons Menu buttons are buttons that have a drop down arrow at the right end of the button Current selection Logging Interval Repeat Log Now Option list Log Later Use menu buttons to access additional functionality and commands When you tap a menu button a drop down list appears Select an option on the list to select the command it describes The label on a menu button does not change when you select a command from the list The label on a list button does The following menu buttons appear in the TerraSync software e Any Options button e The Layers button in the Map section e The Edit button in the Edit dictionary form in the Data section Note Menu buttons differ from list buttons such as the Section list button in their appearance behavio
14. recently used programs list Messaging Internet Explorer 7 59 PM off information While the software is loading a Trimble identification screen appears The software always opens at the Skyplot I Sereen Capture subsection of the Status section To exit the TerraSync software tap J in the upper right B Programs corner of any TerraSync screen a Settings 7 Help Pictures amp Videos File Explorer gee GPS Controller ents To switch to the TerraSync software when it is already running do one of the following Calendar e Use any of the methods described above for starting the TerraSync software e Ona Windows Mobile powered device tap the TerraSync icon of the Windows Mobile Today screen Py at the bottom e Ona Windows office computer tap the TerraSync button on the taskbar Section structure The TerraSync software is arranged in five sections Section Function Map B Data Work with data files e create a new data file or open an existing data file e collect new features or maintain existing features View features background files and the GPS trail graphically e move copy delete or rename data and background files Navigation Status Create and edit waypoints View information about Navigate to features using the Direction Dial and Close up screen e the satellites the TerraSync software is tracking their
15. Assignment and Confirmatory License through which the DOE s rights in the Technology were assigned to the University b Under 35 U S C 203 the DOE has the right to require LizardTech to grant a non exclusive partially exclusive or exclusive license under U S Patent No 5 710 835 in any field of use to a responsible applicant s upon terms reasonable under the circumstances if LizardTech does not adequately attempt to commercialize the MrSID Technology See 37 CFR 401 6 c The University makes no warranty or representation as to the validity or scope of Patent No 5 710 835 and neither the Government nor the University have any obligation to furnish any know how technical assistance or technical data in connection with MrSID software For further information about these provisions contact Lizardtech Inc The Exchange Building 821 Second Avenue 18th Floor Seattle Washington 98104 5 2 The ECW JPEG 2000 Runtime component s of this Software allowing decompression of ECW JPEG 2000 images is provided under license from Earth Resource Mapping Limited 2 Abbotsford Rd West Leederville Western Australia 6007 Any redistribution of such Runtime component s by you is prohibited Trimble Navigation Limited Trimble Europe B V TerraSync Software End User License Agreement Rev 2009 November 23 6 TerraSync Software Getting Started Guide Contents 1 introduction ee cereos 25094 46 OFH64 8454 66465 450 0444 11 Document
16. GPS Pathfinder ProXH receiver e GPS Pathfinder Pro XRS receivers with firmware version 1 52 or later You can use real time carrier corrections from a VRS network to achieve RTK accuracy with e Trimble survey receivers 5800 receiver firmware version 2 23 or later R8 receiver firmware version 2 23 or later R8GNSS receiver firmware version 3 00 or later There are currently two commercial server software products for a VRS network GPSNet from Trimble and GNNET from Geo Both software products can output RTCM messages in the Trimble VRS network message format You can connect the roving receiver to the VRS network using an e Internet connection see page 165 e Direct dial connection see page 170 TerraSync Software Getting Started Guide High Accuracy Data Collection 6 Connecting to a VRS network using an Internet connection You can use an existing Internet connection on the field computer to connect to a single base station or a VRS network that is transmitting corrections over the Internet You can connect to the Internet in a number of ways including a wireless LAN an 802 11b connection or a Bluetooth wireless connection to a Bluetooth enabled cellular phone Note The TerraSync software does not control or configure the Internet connection In the software you only specify the IP address or URL of the VRS network and the port on the server to connect to The rest of this section assumes that you are
17. La N Dees 2 Tap the Subsection list button and then select ae aise Real time External Source MELLEL ting The Real time Summary screen appears eee Ptemal y pp E g Integrated SBAS SNR The TerraSync software is receiving corrections when a real time icon appears beside the source in use This icon indicates the type of correction source 3 To view detailed information about the status ofa correction source tap the Summary button and from the list select the correction source TerraSync Software Getting Started Guide Tutorial Collecting Data 5 D Updating data Your supervisor has sent you to Starfish Bay to update information on existing traffic signs Because you may not always have recorded the original data you may not know exactly where features are You can use the TerraSync software and a real time correction source if available to navigate to them This part of the tutorial gives step by step instructions for the following tasks e Changing the accuracy based logging settings see page 137 e Opening an existing data file see page 138 e Filtering features see page 139 e Selecting a target in the Data section see page 140 e Navigating to a target using the Navigation section see page 140 e Updating a feature see page 142 e Selecting a target in the Map section see page 143 e Navigating to a target using the Map section see page 143 e Marking a feature as updated see page 144 e Navigating
18. Question General error Sound file FeatureStored wav GPSBatterylsDead wav GPSBatterylsLow wav GPSIsConnected wav GPSIsOK wav PoorGeometry wav PositionLogged wav PositionSnapped wav RealTimelsLost wav RealTimelsOK wav LockOpened wav LockLost wav RequiredAccuracyNotAchieved wav StoredMoreThanMinimumPositions wav CloseUpChange wav TooFewSatellites wav The file that the field computer uses for the Question event By default this is Question wav Use the Volume and Sounds system setting to replace the sound for this event The file that the field computer uses for the Critical Stop event By default this is Critical wav Use the Volume and Sounds system setting to replace the sound for this event Color The TerraSync software uses color to make it easier for you to distinguish important information and to distinguish between similar items Color is always used in conjunction with at least one other feature such as a sound icon or bold text The following features of the TerraSync software use color to provide extra information or to clarify the display e Battery icon see page 58 e Map layer colors Map layer colors The information displayed in the Map section is arranged in five layers To make the map display clearer you can select a different color for each of these Map layers If a layer contains features you can either use the feature colors assigned in the data dictionary or set a single color for
19. The Feature Properties dialog appears It provides attribute information about the selected feature 4 To change the color of the Park feature Park x Coo AT b From the shortcut menu that appears select Park Layer Style Thickness The Park dialog appears aie VA Cancel Help For more information about the GPS Pathfinder Office software Map window display search for the topic Map in the GPS Pathfinder Office Software Help a Right click the Park feature on the map c Use this dialog to change the color of the Park area feature type to dark green TerraSync Software Getting Started Guide 125 5 126 Tutorial Collecting Data amp Exporting data to a GIS The Trimble Export utility in the GPS Pathfinder Office software converts files that are in SSF format to a format that can be read by a GIS CAD or database system It lets you export point line and area features attributes and positions to a variety of other formats To export data to a GIS 1 In the GPS Pathfinder Office software select Export from the Utilities menu to start the Export utility F Export ela ea Input Files Folder C TerraSyne Tutorial _ Selected Files Cancel STARFISH cor Help Output Folder C Users JDoe Documents GPS Projects Tutorial E xp Browse Choose an Export Setup Sample ESRI Shapetile Setup nd Format ESRI Shapefile Type of Export Features Positions and Attributes Outpu
20. Then obtain the installation code for your copy of the software and install the software For more information see Obtaining your installation code after registration page 24 9 If this is the first time that you have registered a Trimble Mapping and GIS product the Mapping amp GIS Industry Details page appears From the drop down lists select your organization type and most common market segment and then click Save 22 TerraSync Software Getting Started Guide Installation code Software Installation and Activation 2 You are returned to your My Trimble page where the software you have just registered now appears in the My Products section Home Windows Internet Explorer DES Ker a http support trimble com CPRS Home aspx v tt x es ogl e aj File Edit View Favorites Tools Help a oO a oscar Approval or Review Erone x a B ah E Page iG Tools My Products Add Click amp to see more details about a product Click a Serial Number value to update or extend details for that product Click the associated Your Reference value to add or modify Your Reference for that product Click the associated to remove that product from this list You have registered the following products Product Name Serial Number Wer Reference GPS Pathfinder Office software 998363 00300 TE Ei TerraSync Professional 998300 00110 an x software aaa Software Installation Code gt 99830
21. Use real time differential GPS to navigate accurately to existing features To navigate back to a selected feature use the Navigation section or the Map section This part of the tutorial gives step by step instructions for the following tasks Checking the real time status page 136 Updating data page 137 aa Sources of real time differential corrections 1 Tap fH and then select Programs TerraSync to start the TerraSync software 2 From the Section list tap Setup 3 Tap Real time Settings The Real time Settings CAKE form appears AE 4 Inthe Choice J field specify the real time correction source you want to use ee R Choice 1 External Source Note Ifyou cannot use real time corrections or do not Choice 2 Integrated SBAS want to use them select Use Uncorrected GPS No Choice 3 Ee corrections will be applied to your data Real time Age Limit 1 min Depending on the type of GPS receiver you are using and the subscriptions that your organization has to real time correction services you can get real time corrections from any of the following sources External source such as a VRS network data radio or external beacon receiver Integrated SBAS receiver Integrated Beacon receiver Integrated OmniSTAR receiver Integrated RTK radio 5 To configure settings for the correction source tap the Setup button Pal that appears beside the Choice field F
22. When satellites are widely spaced relative to each other the DOP value is lower and position accuracy is greater When satellites are close together in the sky the DOP is higher and GPS positions may contain a greater level of error PDOP Position DOP indicates the three dimensional geometry of the satellites Other DOP values include HDOP Horizontal DOP and VDOP Vertical DOP which indicate the accuracy of horizontal measurements latitude and longitude and vertical measurements respectively PDOP is related to HDOP and VDOP as follows PDOP HDOP VDOP See Dilution of Precision European Geostationary Navigation Overlay Service A satellite based augmentation system SBAS that provides a free to air differential correction service for GPS EGNOS is the European equivalent of WAAS which is available in the United States An ellipsoid is the three dimensional shape that is used as the basis for mathematically modeling the earth s surface The ellipsoid is defined by the lengths of the minor and major axes The earth s minor axis is the polar axis and the major axis is the equatorial axis For more information see Modelling the earth s surface page 188 A feature is a physical object or event that has a location in the real world which you want to collect position and or descriptive information attributes about Features can be classified as points lines or areas For example a road sign is a point feature a road is
23. attribute 211 Attribute Entry Form 84 85 attribute value 211 attribute values filling in from external sensor 182 filtering by tutorial 139 attributes adding 101 auto incrementing 73 displaying 125 editing 142 exporting 126 filtering by 139 for features 93 storing Image files in 71 authenticating connection to VRS network dial up connection 170 averaged vertices collecting features with 108 overview 111 184 backlight changing on Windows Mobile powered device 53 base logging icon 59 base station definition 211 transmitting data over Internet 168 using multiple 154 using TerraSync to set up 198 Batch Processor utility 127 battery receiver icon 58 tooltip 60 baud rate definition 211 for real time correction output from base station 199 beacon external icon 58 tooltip 60 Beacon on a Belt receiver troubleshooting 205 bearing definition 211 bearing bearing offsets overview 181 between feature GPS positions recording 174 Bluetooth wireless technology cellular phone connection 165 167 DUN service 165 Internet connection 165 169 PAN service 165 VRS connection 170 172 VRS network connection 165 169 broadcast server definition 211 See also NTRIP server bull s eye in Close up screen 141 buttons 65 TerraSync Software Getting Started Guide 223 Index C C A code definition 212 carrier phase data collection configuring accuracy 155 principles 151 time and accuracy 153 carrier phase GPS introduction 14
24. collect the gate feature and then use the Continue option to resume collecting the path feature You can continue any line or area feature not just the last one collected provided you have not used the Continue option for any other features since collecting that line or area feature Once you continue a feature you cannot continue any line or area features collected between the two segments of that feature These features are now nested within the continued feature Any features you collected before the continued feature are also unavailable for continuation New features that you collect after the continued segment will be available for continuation because you have not continued any other feature since they were collected If you replace the positions of an existing feature with new GPS or digitized positions the Continue option treats the feature as a new feature so it can be continued Note You can collect as many features within a line or area as you need The number is limited only by storage space on the field device TerraSync Software Getting Started Guide 175 A Advanced Datalogging Options 176 Offsets If you cannot travel over the top of or right next to a feature you can enter an offset and record it at the specified distance When collecting a tree feature for example it may be easier to stand some distance for example 10 paces to the North from the tree and record its attributes This ensures good GPS re
25. definition 218 position logging paused icon 59 tooltip 61 positions accuracy 209 logging later 102 postprocessing software 13 postprocessing software post processing rover data 198 postprocessing definition 218 Predicted Postprocessed Accuracy PPA overview 157 159 preparing for data collection 92 for data update 128 primary pane 81 PRN definition 218 Pro XRS receiver see GPS Pathfinder Pro XRS receiver problems with GPS 204 with position accuracy 209 with real time corrections 205 with Windows Mobile powered device 203 projection 189 218 ProXH receiver see GPS Pathfinder Pro series receiver ProXT receiver see GPS Pathfinder Pro series receiver 47 pseudorandom number definition 218 Q questions 74 R8 GPS receiver 48 148 radio troubleshooting 205 raster graphics definition 218 real time corrections external icon 58 real time differential correction definition 219 troubleshooting 205 real time differential correction sources 135 real time icons beacon 58 external 58 external beacon receiver 58 external RTK 58 integrated RTK radio 58 satellite 58 SBAS 58 real time kinematic data collection See RTK data collection real time external icon 58 tooltip 60 real time integrated icon 58 tooltip 60 receiver troubleshooting 204 receivers 148 carrier postprocessing capable 148 H Star capable 148 RTK capable 148 receivers supported 47 Recon GPS CF Card receiver 47 recording area line point featur
26. device by the manufacturer TerraSync Software Getting Started Guide 35 2 Software Installation and Activation Make sure that you have enough free memory to install the font TerraSync language fonts require 9 to 10 MB of free memory For more information see Installing the TerraSync software onto a Windows Mobile powered device page 26 Insert the TerraSync Software CD in the CD drive of the office computer Alternatively if you are entitled to an upgrade from a previous version of the TerraSync to version 4 10 you can download the software from www trimble com terrasync_ts asp Click Downloads and then click v4 10 Software The Setup screen appears Ss TerraSync Mea e a Trimble TerraSynce software Version 4 10 Main Menu Install Register Read documentation www trimble com 1995 2008 Trimble Navigation Limited All rights reserved This product is protected by US and intemationel copyright trademark and patent laws as described in Status About Note If this screen does not appear select Autorun exe from the CD drive folder 4 5 6 7 Select the Jnstall option Select the nstall fonts option Select the option for the language that you require Follow the instructions on the screen to install the font Note TerraSync fonts should always be installed to RAM main memory Do not install fonts to a secondary internal storage location such as the Disk on a GeoExplorer series hand
27. filtering to positions as they are recorded If at least one valid real time correction source is selected in the Real time Settings for and the last Choice field is set to Wait for Real time then only real time positions are filtered e If you intend to postprocess the data set the Log Velocity Data field on the Logging Settings form to On Then when you differentially correct the data in the postprocessing software use the velocity filtering option to smooth uncorrected positions No configured real time source is available so the TerraSync software is using uncorrected positions In the last Choice field on the Real time Settings form select Wait for Real time to use differentially corrected positions only You are unable to differentially correct GPS positions either in real time or in postprocessing The TerraSync software used satellites that were not visible to the base station Make sure that the minimum elevation value in the TerraSync software is set sufficiently high so that the software only uses satellites which are also visible to the base station Try correcting the data using another base station file You reset the receiver and began logging data before a new almanac was collected causing the TerraSync software to use satellites that were not visible to the base station Wait until the receiver has collected a new almanac before you log data Real time corrected GPS po
28. tap the Subsection list button and select the subsection you want from the drop down list m lerraSync For example if you are in the Skyplot subsection of the Status section the Subsection list button displays Skyplot To switch to the Satellite Information subsection tap the Subsection list eee ppop button and select Satellite Information Productivity Precision ee ew Some subsections are not always available For example in the Data section you cannot open the Collect Features subsection until you open or create a data file Some screens also contain buttons and menu buttons that let you open other screens or forms TerraSync Software Getting Started Guide Section structure lists Software Structure The following lists outline the TerraSync software section structure Use them as a reference until you are familiar with the sections and their subsections Map section 4 Map Tools Select Zoom In Zoom Out Pan Digitize Measure Options Layers Undo Zoom Extents Auto Pan to GPS Position Auto Pan to Selection Filter Update Selected Feature Delete Selected Feature Set Nav Start GPS Map Point Selected feature Map Point Construct Set Nav Target Selected feature Clear Nav Targets Cross Track Light Bar Enter Coordinates Refresh Filtered Features Unfiltered Features Waypoints Background Between Feature GPS GPS Trail B
29. 3 Install the software using the TerraSync Software CD and the installation code you obtained when you registered your copy of the software 4 Activate the software depending on the handheld operating system TerraSync Software Getting Started Guide 17 2 Software Installation and Activation System requirements Field computer specifications Version 4 10 of the TerraSync software runs on handheld devices running any of the following Microsoft operating systems e Windows Mobile 6 operating system e Windows Mobile version 5 0 software e Windows Mobile 2003 software Version 4 10 of the TerraSync software runs on computers running any of the following Microsoft operating systems including 64 bit variants e Windows Vista SP 1 Ultimate Edition Enterprise Edition Business Edition or Home Premium Edition e Windows XP SP 3 Professional Edition Home Edition or Tablet PC Edition e Windows 7 Ultimate Edition Enterprise Edition Professional Edition or Home Premium Edition For detailed specifications go to www trimble com terrasync_specs shtml Required software To install the TerraSync software onto a Windows Mobile powered device and to transfer files between a desktop computer and a Windows Mobile powered device you must have the appropriate Microsoft software installed on your computer or Tablet PC The software you use to manage the connection between the device and the computer depends on the operating s
30. 4 Move right Map Alt right arrow key Alt 6 TerraSync Software Getting Started Guide 67 3 User Interface and Data Entry Action Section Keyboard shortcut Open Existing File subsection Data Alt X Open File Manager subsection Data Alt G Open Satellite Info subsection Status Alt F Open Receiver subsection Status Alt V Open Real time subsection Status Alt A Open Plan subsection Status Alt P Open Sensor subsection Status Alt R Open Comms subsection Status Alt O Open UTC Time subsection Status Alt 1 Open About subsection Status Alt B 68 _ TerraSync Software Getting Started Guide User Interface and Data Entry 3 Data entry fields The method you use to enter data in a field on a form depends on the type of field you are entering data into and on the availability of keyboards The following field types can appear e Text see page 69 e Numeric see page 69 e Menu see page 70 e Time see page 70 e Date see page 71 e Filename see page 71 If the field computer has a physical keyboard use it to enter text or numbers just as you would in any Windows program If you do not have a keyboard use the on screen keyboards for data entry An on screen keyboard is a small dialog that pops up from the taskbar when you select a field that allows data entry You can also manually activate an on screen keyboard at any time Use the on screen keyboard to s
31. 84 or the Existing File screen see page 84 to open an existing file There are no features in the file to display Open the Collect Features screen to collect some features see page 84 The layer in the Map section that the features belong to has been turned off or the group in the Data section that the features belong to has been hidden In the Map section tap Layers and select Filtered Features or Unfiltered Features to display the appropriate layer see page 83 In the Update Features screen tap Options and then select Show Filtered Features or Show Unfiltered Features to display the appropriate group see page 84 The background file in the Map section is turned off or has not been selected If the data you want to see is in a background file use the Background File form to check that the map is set to display this file see page 83 Then tap Layers and make sure that the Background option has a check mark beside it The zoom scale is incorrect You are viewing the wrong area in the Map screen Check that you are not zoomed in too close or out too far to see the data If you have distant items to display the zoom extents of the map will be at a more distant scale Use the Pan map tool see page 83 or the Pan button on the Command bar to pan the display to the appropriate area Use the Zoom Extents mode see page 83 or the Zoom Extents button on the Command bar to zoom to a
32. An ActiveSync technology partnership with another Windows Mobile powered device is interfering with connection to the device In ActiveSync technology delete any partnerships with other Windows Mobile powered devices Use a guest relationship not a partnership Data transfer is slow The Windows Mobile powered device is not configured to connect at the maximum baud rate available Increase the connection speed See the installation instructions The TerraSync software does not list the COM port that you want to use You added the COM port after you started the TerraSync software For example you inserted a PC card adaptor into a PCMCIA or CompactFlash slot on the field computer The port is a Bluetooth port that is no longer available The TerraSync software only checks which COM ports are defined when it starts up To force the software to check for new COM ports exit and then restart the TerraSync software Note On a GeoExplorer series handheld the COM1 serial port is always defined even if the serial clip is not connected to the handheld Re enable Bluetooth to re configure the COM port The desktop computer does not connect to the Windows Mobile powered device The device is not set up to establish an office computer connection Open the Communications Properties dialog on the device For information on how to do this refer to the documentation for the device Select the PC Con
33. Bearing line from B l l l Feature Bearing fronl A Bearing from B Bearing line from C TerraSync Software Getting Started Guide 181 A Advanced Datalogging Options 182 Using a laser rangefinder to record offsets You can use a laser rangefinder to record accurate offsets for a feature To use a rangefinder with the TerraSync software you only need to specify which serial COM port on the field device the rangefinder is connected to Note This option is not available in the TerraSync software Standard edition For a list of the laser rangefinders that the TerraSync software supports go to www rimble com terrasync_specs shtml To record an offset from a laser rangefinder make sure that a feature is open and that the attribute entry form for the feature the appropriate offset form or the Map screen is open Then fire the laser rangefinder The TerraSync software stores the distance and if the laser rangefinder supports it the bearing in the appropriate field s in the offset form Before storing an offset from a laser rangefinder the TerraSync software subtracts the antenna height from the measurement The antenna height is specified in the Setup section An incorrect antenna height can reduce the vertical accuracy of the position of the feature If vertical accuracy is important make sure that you do the following e Set the antenna height to the vertical distance from the laser rangefinder to the a
34. Garbage Can 3 Tap Create From and then select GPS to automatically fill out the coordinate fields using the your current position New Waypoint Name 4 When you finish entering information for the waypoint tap OK Latitude The waypoint is created and the Waypoint List ae ongitude screen appears H 5 To close the waypoint file tap Options and then Altitude HAE Meters tap Close File i I Later in this tutorial you will use the waypoint to navigate back to this location You can then collect the installed garbage can as a feature TerraSync Software Getting Started Guide 105 5 Tutorial Collecting Data Ending the data collection session When the data update session is complete exit the TerraSync software You do not have to close the data file first If you exit the software while a data file is still open the TerraSync software closes the file before exiting To exit the TerraSync software 1 Tap EJ in the upper right corner of the screen 2 When prompted to confirm closing the file and exiting the software tap Yes 106 TerraSync Software Getting Started Guide Tutorial Collecting Data 5 Exercise 3 Advanced data collection This exercise is optional and gives you practical experience using some techniques for collecting out of the ordinary features such as those that are inaccessible places near trees or in a high mu
35. Name to customize it to your environment Depending on the connected device type you may also be required to enter the device serial number Online activation The Wizard communicates directly with the Trimble Activation server and activates the TerraSync software on your field computer Activation Wizard Trimble Online Activation Please wait while activation is in progress Status Contacting the Trimble Activation Server A Cancel Activation using an existing Activation Key The Activation Wizard prompts you for the folder where the Activation Key is stored This could be on a local or network drive or an external memory card such as a USB memory stick or SD card Activation Wizard SINA Select Activation Key Activation Key path TerraSync Software Getting Started Guide 39 2 Software Installation and Activation Use the Browse button to navigate to the required folder Browse For Folder E B My Documents p My Computer E 4 My Network Places g Recycle Bin E7 R My DocuShare Places 3 Downloads ProcessExplorer Program FilesTerraSync If the Activation Wizard cannot find an Activation Key for the connected device in the selected folder it will continue to prompt for a different folder Activation succeeds only if the Activation Key matches the connected field computer Activation Wizard SAL am completed The Trimble TerraSyne software installed o
36. Needs replacing in the Condition attribute To show only these signs you must filter by attribute value on the feature type Traffic Sign To filter features 1 Tap the Subsection list button and then select Update Features 2 Tap Options and then select Filter The Filter By form appears 3 Make sure that the Features check box is selected 4 Inthe Traffic Sign field select Filter By The Attribute Test and Value fields appear below the Traffic Sign field 5 Inthe Attribute field select Condition 6 Inthe Test field make sure that Equal To is selected 7 Inthe Value field select Needs replacing 8 Tap OK to close the Filter By form and return to the Update Features form If a feature in the Choose Feature list meets the conditions you specified the filter icon F appears in the Filter column for that feature There is one traffic sign that meets the filtering conditions TerraSync Software Getting Started Guide Update Filter By Update Status Deleted Status Features Traffic Sign Garbage Can Light Pole Tree 0 ya Unfiltered Unfiltered v Unfiltered Unfiltered v a TerraSync 5 Update 7 File Starfish Choose Feature z Name yr Distance x Traffic Sign Y B fu Road 7 Waterbody 6 fu Path 5 fu Road k u fu Road B a Road H 2 Tu Road 2 bd KH l gt
37. Pause When you are ready to continue walking tap Resume tap Options and then select Segment Line 9 From the Surface Type field select Asphalt 10 Walk to the end of the asphalt segment 11 Once you finish logging the last segment tap OK to save the feature and return to the Collect aw Features screen Oyster Lane Number of Lanes 2 Surface Asphalt T Condition Needs repairing v OK a Pause 110 TerraSync Software Getting Started Guide Tutorial Collecting Data 5 Q Collecting a point feature while collecting a line feature nesting You need to collect the light poles that are on Seaweed Street You have not yet recorded Seaweed Street and to save time you will collect the light pole features at the same time as you collect the Seaweed Street feature To do this you will nest the point features within the line feature Note Only point features can be nested in this way To collect a line or area feature while you are collecting another you must use the Continue option Lamp Posts Seaweed Street To nest a point feature 1 Make sure Log Later is selected To do this tap Options and then select Log Later In the Collect Features screen select the Road feature and then tap Create In the Name field enter Seaweed Street Tap Log a fF we NM Walk along Seaweed Street until you reach the first light pole and then tap Pause TerraSync Software Getting
38. Sea Level MSAS MSL MTSAT Satellite Based Augmentation System multipath NAD 27 Latitude is an angular measurement made from the center of the earth to north or south of the equator It comprises the north south component of the latitude longitude coordinate system which is used in GPS data collection Traditionally north is considered positive and south is considered negative The datum chosen for use in a particular region Positions on a local datum are commonly called local geodetic coordinates Coordinates are traditionally given in terms of the local datum When you survey using the satellite based Global Positioning System GPS however the coordinates you collect are based on the World Geodetic System 1984 These coordinates are given in terms of the WGS 84 datum Before you can use WGS 84 coordinates with coordinates measured in terms of the local datum you must perform a datum transformation The ellipsoid specified by a coordinate system The WGS 84 coordinates are first transformed onto this ellipsoid then converted to grid coordinates To track sufficient satellites for logging carrier phase or H Star data Loss of lock occurs when the number of available satellites drops below four when logging a static GPS position or below five when logging a streaming GPS position Loss of lock can also occur during H Star data collection if the PDOP rises above 6 Longitude is an angular measurement made from the
39. The Installation Code is assigned to another device Activation Wizard ts 5 SLL Enter an Installation Code The following Installation Code is already in use 521494 00110 09134 6BA04 453 It is currently associated with Device Name Juno SB Handheld Device Serial Number 123456789 Please enter another Installation Code In these circumstances enter a valid or previously unused Installation Code If in doubt contact your Trimble reseller 42 _ TerraSync Software Getting Started Guide Software Installation and Activation 2 Starting the TerraSync Software on a field computer powered by the Windows Mobile version 5 0 software or version 6 operating system TerraSync software version 4 00 will run on a field computer only if it is successfully activated Ifa valid Activation Key is not found the following error message appears ne ferraSync gt Sunday 5 41 PM ___ November 01 2009 Invalid Activation Key Please activate TerraSync by following the activation instructions in the TerraSync Getting Started Guide 2000 2009 Trimble Navigation Limited All rights reserved This product is protected by US and international copyright trademark and patent laws as described in Status About Calendar GPS Tap ok to exit and then run the Activation Wizard to activate the software see page 37 Installing the TerraSync software onto a Windows computer This section describes how to ins
40. The TerraSync software does not prevent you from closing a feature before the required accuracy is achieved or before the lock period is complete For more information about how the duration of carrier lock affects accuracy for each carrier phase data collection technique see e H Star technology workflow and required infrastructure page 154 e Carrier phase postprocessing workflow and required infrastructure page 158 e Real time kinematic workflow and required infrastructure page 160 TerraSync Software Getting Started Guide 153 6 154 High Accuracy Data Collection H Star technology workflow and required infrastructure This section explains in more detail how to obtain subfoot accuracy using H Star technology H Star technology enables you to quickly achieve high accuracy with only short periods of carrier data For example you can achieve subfoot accuracy or better with two minutes of continuous data If lock on satellites is maintained subsequent positions need only minimal occupation times Unlike RTK using real time H Star technology generates usable positions within the first two minutes of data collection but they may not meet your accuracy requirements until the receiver has recorded a two minute block of data When collecting positions using a VRS network as the real time correction source or when postprocessing the data using H Star processing the positions are corrected using data from a group of base stations
41. a ove gies Ws Bb ah ane Senate et AE od Sa ere ego eon we aa 63 Lists Airy Sew Se ah ek BS E Se Glan ie A BA a at oe eae ae aad 64 BUUCONS Sto dB de ae BG OS E eh Oa ee ea a 65 Keyboard shortcuts o s so iio de wake eS N Ae eee RGE aE ae ne oe Re A 66 Data entry telds sisted al Bed ww eles ole Gok ante A ae ede wh Al Ades SOA a ia E 69 Auto incrementing attributes aaua 73 Pop up messages soe Gated he Se a Ae de EE AL eae we a aia 73 TROOPS 4 22544 ab ase nok T Ges ee don UR EAN aes Gr Ee ek a 74 SOUNE 4 206 k Be VE Naa oe ERAS yee BEE Ree eed eae Ss 75 COLOR geist date ek bh E irp eee ale Sotho aie bh dR duet gw el ed Be de 77 4 Software Structure a ceco a es eee awe eda a we ee ees 79 Introduction seai ho RE Ras PAE OE REG ba Se ee Rhee DOSE ee Ra 80 SCCHONS 5 oie s eee AE Oe a RE a ea See hd eee ee baw E 80 Panes sxc a spo Bee iad a Go as wa eae Mee be Ge Be eo 81 Secon Structure aw lor eed od eGo e E E Se a E PE odie a Mare Galea 82 Section str ct re lists secre wh ek Dae a ae kg od I OG ee oe me a 83 5 Tutorial Collecting Data occo cearna e cere ees ee ee wee 89 Tutorial Structures ss tace A ee eA Oe eds Pe RE awe eee eee wae 90 Tutorial SC6MariO w s e Ged Bob nd Gon ew OG A Od koe ee eo eh amp ht 91 Data collection 4 0 4 was tdivak dees age cats Shee Le whose ob Chee Se 91 Data tipdate ssa saiet a a e dew ea ieee SE ede we eed 91 Exercise 1 Preparing for data collection 2 0 2 eee ee eee 92 Cr
42. any time You may move the Software from one computer to another provided that you first uninstall the Software from the original computer deactivate it as required and then reinstall it on the new computer You may authorize the personnel associated with your business to use the Software but likewise use is limited to only one person at one time on one computer at one time You may also store or install a copy of the Software on a storage device such as a network server used only to install the Software on your other computers over an internal network but in such case you must acquire and dedicate a license for each separate computer on which the Software is installed from the storage device A license for the Software may not be shared or used concurrently on different computers 1 2 Other Rights and Limitations 1 You may not copy modify make derivative works except for Customized Applications of rent lease sell sublicense distribute or transfer the Software in whole or in part except as otherwise expressly authorized under this Agreement and you agree to use all commercially reasonable efforts to prevent its unauthorized use and disclosure You may make one copy of the Software for archival purposes Disabling any licensing control features is prohibited 2 The Software contains valuable trade secrets proprietary to Trimble and its suppliers To the extent permitted by applicable law you shall not nor allow any third p
43. base data from multiple base stations to obtain better postprocessed accuracy for the collected data once back in the office See Web map server ITRF A reference frame defined by the International Earth Rotation Service IERS with its origin at the Earth s center of mass The WGS 84 datum is aligned with the current realization of ITRF ITRF 2000 also called ITRFOO IMS See Web map server Ionospheric noise is the effect that the ionosphere has on GPS signals The ionosphere is the band of charged particles 100 to 200 kilometers 60 to 125 miles approximately above the surface of the earth See International Terrestrial Reference Frame The primary L band carrier used by GPS satellites to transmit satellite data The frequency is 1575 42 MHz It is modulated by C A code P code or Y code and a 50bps navigation message The secondary L band carrier used by GPS satellites to transmit satellite data The frequency is 1227 6 MHz It is modulated by P code or Y code and a 50bps navigation message An instrument that uses a laser beam to accurately measure the distance to a target Some rangefinders also measure the bearing to the target Use a laser rangefinder to measure offsets when you are unable to record positions at the exact location of the feature TerraSync Software Getting Started Guide 215 Glossary latitude local datum local ellipsoid lock longitude magnetic declination magnetic north Mean
44. base station An unattended base station once set up continues to operate without any controlling software After you have used the TerraSync software to configure the base receiver and the base station has started broadcasting corrections you can disconnect the field computer and connect it to the roving receiver To set up an unattended base station L Connect the field computer that the TerraSync software is installed on to the base receiver From the Data section open the New File screen and start a new base data file Step through the Base Station Setup wizard In the Real Time Output step make sure that you set the Correction Output field to Receiver Port to enable real time output If the base receiver is a survey receiver a message appears before the new base file is opened warning that you cannot collect base data using this receiver Tap OK to continue To confirm that the receiver is generating correction messages make sure that the base station icon is visible in the status bar Disconnect the TerraSync software from the base receiver Do one of the following Physically disconnect the field device from the base receiver Inthe TerraSync software disconnect from GPS Exit the TerraSync software without closing the base file Tip Whenever you close the base file while the TerraSync software is connected to the receiver the receiver stops generating real time output If you want the base receiver to
45. continue operating unattended do not close the base file before disconnecting from the base receiver TerraSync Software Getting Started Guide Troubleshooting In this appendix Communications Field computer GPS Real time differential correction Data files Map screen Coordinate system Position accuracy TerraSync Software Getting Started Guide 201 Appendix This section lists possible causes of and solutions to problems you may encounter when using the TerraSync software D Troubleshooting Communications The following table describes possible causes of communication problems Problem Possible cause Solution The ActiveSync technology does not connect to the Windows Mobile powered device The device is not connected securely to the cradle or data cable Check cabling and then try to connect again ActiveSync technology has timed out The TerraSync software is trying to connect to the GPS receiver using the COM port that ActiveSync technology is using Lift the device out of the cradle and then replace it Unplug the data cable of the device and then plug it in again Disconnect from GPS see page 88 or exit the TerraSync software The serial COM port is configured in the TerraSync software for use with a laser rangefinder Exit the TerraSync software Change the selected port in the Laser port field on the Logging Settings form see page 88
46. data update 1 ee ee 128 Creating a data dictionary from existing datafiles 0 0 0 00004 128 Importing data from a GIS into the GPS Pathfinder Office software 130 Transferring data to the field computer 0 0 00 e eee eee ee 133 Exercise 6 Dataupdate sce c soco ee eae 135 Sources of real time differential corrections 0 000000 eee eee 135 Checking the real time status eee ees 136 Updating data 233 804 ceeds debe Aea EEE diene daa tenes bbasaes 137 High Accuracy Data Collection 0 2c nnna 147 Introduction to carrier phase GPS 1 ee ee 148 Carrier phase techniques compared naasna 149 H Star technology scissile te ee ele Ral Re Ge eae ee a ae 149 Carrier phase postprocessing 1 2 ee eee 149 Real time kinematic RTK 0 0 0 ee eee 150 Principles of carrier phase data collection 2 2 eee ees 151 Carrier lock esi es oe atta Gia ee oe Deb aid ee eee Sade Mea al a Sans 151 WTA ZAMOM ois ea 4 As Sty an e ages die Ak ie ee kd od Onda ee a 151 Carrierblocks s 5 sie a ls ak oo Sie pE E Sig Gk ape pl ely a oe ob nes 151 The relationship between time and accuracy 0 eee ee eee 153 H Star technology workflow and required infrastructure 0 0 0 0000 c eee eee 154 Required infrastructure for H Star technology 0 00 0 154 Configuring the TerraSync software to collect H Star data 0 0 155 Collecting sufficient high accuracy dat
47. e Inthe Address field enter the IP address or URL of the VRS network or the server that is supplying the corrections from the VRS network Typically the IP address or URL of a VRS network has the format 218 101 54 6 5024 where the digits before the colon are the address and the digits after the colon are the port number f In the Port field enter the port number that you will use to connect to the server g Ifyou are connecting to a VRS network through an NTRIP server tap the Setup button H beside the Source field The GPS field software attempts to establish a connection to the NTRIP server If the connection is successful the Select Server form appears Select the server that you want to use and then tap OK to return to the External Source Settings form h Ifyou selected a VRS network that requires authentication the Name and Password fields appear Enter the user name and password that you obtained from the service provider 168 TerraSync Software Getting Started Guide High Accuracy Data Collection 6 i From the Connection Control field select Auto if you want the TerraSync software to automatically establish and end connections to the VRS network as necessary Manual if you want to connect or disconnect only when you tap Ext Source in the Setup screen j Tap OK to confirm the settings and return to the Real time Settings form 5 Tap OK to confirm the real time settings and return to the main screen
48. form see page 88 check that the configured maximum DOP value PDOP or HDOP is not too low Unable to connect to the GPS receiver The receiver firmware is not supported by the version of the TerraSync software Check the Compatibility Matrix and use the correct versions of the receiver firmware and the TerraSync software 204 TerraSync Software Getting Started Guide Real time differential correction This section lists problems you may encounter when using real time differential corrections or real time differential correction sources Troubleshooting D Problem Possible cause Solution Not all positions are corrected in real time You have chosen to use uncorrected GPS if no real time corrections are available From the last Choice field on the Real time Settings form see page 88 select Wait for real time The TerraSync software is not using the first choice real time correction source The first choice correction source is not available so the second or third choice is being used In the Real time section see page 87 check the status of your preferred correction source If necessary change the configuration in the Real time Settings form see page 88 or wait until this source is available again The correction source you expected is not set up as the preferred source In the Real time Settings form see page 88 select your preferred real time correcti
49. in tooltips 74 pop up 73 minimum specifications 18 MSL definition 216 multipath definition 216 My Trimble account 20 24 NAD 27 definition 216 NAD 83 definition 217 navigating in the Map section 143 in the Navigation section 140 Navigation section 81 navigation software 185 navigation target setting tutorial 140 nesting features 111 new data file creating tutorial 100 selecting data dictionary tutorial 100 NMEA defined 217 northing converting 190 not in feature positions See between feature GPS positions NTRIP server 217 See also broadcast server numeric keyboard 55 Oo office computer 217 offsets adding to features 178 collecting features with 115 116 complex 178 overview 176 recording with laser rangefinder 182 on screen keyboards 54 228 TerraSync Software Getting Started Guide opening existing file tutorial 138 Options menu buttons 66 orientation 12 other software required 18 P panes 81 parity definition 217 Partnership Settings screen 166 partnership definition 217 passcode 166 pausing logging overview 174 to ensure only vertices are recorded 184 pausing logging tutorial 102 PC battery level 58 definition 217 specifications 18 troubleshooting 203 PDOP definition 218 Personal Area Networking PAN service 165 point features collecting while recording line or area features 175 offsets 176 POPN 19 22 pop up messages 73 portrait orientation 12 Position Dilution of Precision
50. is allocated to programs because too much is allocated for storage Adjust the memory allocation For more information refer to the documentation for the device There is not enough free memory on the field computer Delete unwanted files The screen is not visible outside or in bright light The backlight brightness is too low Adjust the backlight brightness See page 53 A file attached to a filename field does not open or play ona desktop computer The file has been recorded in a special file format that is used only on a Windows Mobile powered device or on a specific brand of Windows Mobile powered device For example there are a number of ways of encoding WAV wav audio files that are specific to one brand of device In the software that you use to record or create the file change the settings to record files in a format that can be read ona desktop computer A TerraSync software data file has been The field computer was reset or the batteries were removed while the Open the file in the TerraSync software The software automatically repairs and rebuilds corrupted software was logging data the file Note If you suspect that a file is corrupted rebuild it before transferring it to the office computer or sending it by email The TerraSync The TerraSync software is not yet Run the Activation Wizard on the computer software has not been activated activated on the dev
51. keyboard button in the taskbar The currently selected on screen keyboard pops up and partially covers any screen that is open When you have finished entering text in a field tap Enter to accept the text you have entered and move to the next field To hide the on screen keyboard tap the keyboard button on the taskbar again An on screen keyboard usually consists of rows of keys The default keyboard shows alphabetic or alphanumeric keys laid out like a real keyboard As you tap each key the corresponding character is added to the current text or numeric field in the current program Alternatively an on screen keyboard may use character recognition Normally when using a character recognition keyboard you write with the stylus in a special field As you draw each shape it is translated into the corresponding character and entered into the current field You can correct any text that is incorrectly interpreted You can install different on screen keyboards on the device and switch between them as required All of these keyboards are available when you use the TerraSync software For example you may want to use a character recognition keyboard to quickly enter a long note an alphabetic keyboard to enter a filename and the Trimble numeric keyboard see page 55 to enter numeric data such as the height of a feature or a distance If the device has on screen keyboards installed the TerraSync software automatically displays the appropr
52. lerraSync Setup Antenna Settings OK Cancel Height Confirm Per File Type Unknown External a Part Number n a X Measure Height To Bottom of antenna mount If you are using an external antenna select the appropriate Measure Height To option Tap OK to save your settings and return to the Logging Settings form You can leave the rest of the fields at their default settings Tap OK to close the Logging Settings form TerraSync Software Getting Started Guide Tutorial Collecting Data 5 Configuring GPS quality settings Note Ifyou are using a Juno series handheld a Trimble Nomad G series handheld a Trimble Nomad handheld a Trimble Recon GPS XB or XC edition a GPS Pathfinder XB or XC receiver or a Trimble Yuma rugged tablet computer you cannot configure GPS settings When you open the GPS Settings form the GPS slider does not appear and the settings for these receivers are shown as read only fields Use the GPS Settings form in the Trimble GPS field software to configure the GPS quality settings you require The lower the GPS quality settings the more productive you are likely to be as the GPS receiver will track more satellites and be better able to calculate a GPS position The stricter the GPS quality settings the more precise the GPS positions that are calculated This means that if you log a series of GPS positions for the same point they will be less spr
53. log GPS positions Enter the remaining attributes for the Squid Way feature TerraSync E Data amp 0 i Collect File Starfish Eontinue cance Name Choose Feature Pu Road fu Road fu Road fu Road fu Road Gi Path amp Waterbody F T Name ID Squid Way Condition When you reach the end of Squid Way tap OK to save the feature and return to the Collect Features screen TerraSync Software Getting Started Guide Tutorial Collecting Data 5 Collecting a line feature using a centre offset simple offset You want to record a fence that you cannot get close enough to because of dense undergrowth You must enter an offset for the fence and record it at a specified distance The fence is in Starfish Park and runs parallel to Seagull Street Seagull Street To record an offset for the fence feature 1 Start walking along the sidewalk on Seagull Street until you reach the fence which is four meters on your right 2 Inthe Collect Features screen tap the Fence feature and then tap Create 3 Inthe attribute entry form enter Seagull Street Fence in the Name field 4 Tap Options and then select Offset 5 From the Direction field select Right cone Leg 6 Inthe Horizontal distance field enter 4 meters Tox Leave the Vertical distance at the default of zero ae 7 Tap OK to save the offset value noo Besse Vertical distance
54. of the Setup section If you selected Auto in the Connection Control field the Ext Source button is depressed and the software attempts to connect to the server 6 Ifyou selected Manual in the Connection Control field tap the Ext Source button that appears below the Status bar in the Setup section to connect the TerraSync software to the Internet correction source Tip To disconnect or reconnect to the server at any time tap Ext Source To view the status of the real time correction source open the Status section select the Real time subsection and then select External from the Summary list button Reconnecting to the Internet To reconnect to the Internet at any time after setting up the connection repeat steps 3 through 8 on page 167 If you selected Auto in the Connection Control field of the TerraSync software the software automatically connects to the Internet source that is providing real time differential corrections To manually reconnect the TerraSync software to the Internet source that is providing real time differential corrections open the software and then tap the Ext Source button that appears below the status bar in the Setup section TerraSync Software Getting Started Guide 169 6 170 High Accuracy Data Collection Connecting to a VRS network using a direct dial connection The direct dial connection method uses a cellphone and modem or a cellular modem to dial up the base station or VRS network dir
55. or 30 days whichever is longer 3 3 NO OTHER WARRANTIES TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW TRIMBLE AND ITS SUPPLIERS DISCLAIM ALL OTHER WARRANTIES TERMS AND CONDITIONS EITHER EXPRESS OR IMPLIED BY STATUTE COMMON LAW OR OTHERWISE INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES TERMS AND CONDITIONS OF MERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE TITLE AND NONINFRINGEMENT WITH REGARD TO THE SOFTWARE ITS SATISFACTORY QUALITY AND THE PROVISION OF OR FAILURE TO PROVIDE SUPPORT SERVICES TO THE EXTENT ALLOWED BY APPLICABLE LAW IMPLIED WARRANTIES TERMS AND CONDITIONS ON THE SOFTWARE ARE LIMITED TO EITHER 90 DAYS FOR TERRASYNC STANDARD EDITION OR ONE 1 YEAR FOR TERRASYNC PROFESSIONAL EDITION YOU MAY HAVE OTHER LEGAL RIGHTS WHICH VARY FROM STATE JURISDICTION TO STATE JURISDICTION The foregoing limited warranty and customer remedy provisions under Sections 3 1 and 3 2 shall not apply to Software obtained as freeware without charge such as for example evaluation or demonstration copies whether from Trimble an authorized Trimble dealer or otherwise Such Software obtained without payment of a license fee is furnished AS IS without warranty of any kind unless the user has separately purchased applicable warranty and or support coverage 3 4 LIMITATION OF LIABILITY YOU ASSUME ALL RISK AS TO THE RESULTS AND PERFORMANCE OF THE SOFTWARE TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW IN NO EVENT SHA
56. or Tablet PC then the office computer may actually be the same computer as the field computer A digital message is composed of 0 s and 1 s Parity is a form of error checking that sums the 0 s and 1 s of the digital message A parity error results when one of the bits is changed so that the parity calculated at message reception is not the same as it was at message transmission Options for parity checking include even odd and none Typically you should have the same parity setting on the Windows Mobile powered device as on the external device you are communicating with A partnership lets a Windows Mobile powered device exchange and share information with a desktop computer You need a partnership or a guest connection to transfer data between the TerraSync software on the device and the GPS Pathfinder Office software on the desktop computer A partnership stores information about e howto connect to the device e what types of files you can send and receive e what files you can synchronize and how to manage synchronization e howto convert files for transfer Unlike a guest connection a partnership is stored on the desktop computer and remains when the device is disconnected from the desktop computer For more information refer to the ActiveSync Help In TerraSync software documentation a field computer that is running a supported Windows desktop operating system See Position Dilution of Precision TerraSync Software Gettin
57. paused and the pause icon flashes in the Status bar New positions are logged for an existing feature only after you tap Log in the attribute entry form and select the Update position option If you select the Log Later option the TerraSync software begins logging positions for a new feature only after you tap Log in the attribute entry form Until you begin logging the pause icon flashes in the Status bar When Log Later is selected a bullet appears beside it in the option list To select Log Later tap Options in the Collect Features screen and then select Log Later from the drop down list Recording between feature positions 174 The GPS data collected using the TerraSync software is recorded in files You can collect positions in a file without collecting feature and attribute data These positions are called between feature positions They appear in their own layer on the Map graphical screen Recording GPS positions only is useful if you do not need to record feature and attribute data For example you may want to record a trail of the dayss activities to track where you have been In this case you would not want to collect feature or attribute information only the positions You can also use between feature logging to record the route traveled from one feature to the next TerraSync Software Getting Started Guide Advanced Datalogging Options A By default the TerraSync software does not record between feature positio
58. relative positions in the sky and your current position e the GPS receiver and real time correction source e the TerraSync software version and trademark information Configure the TerraSync software nf Setup TerraSync Software Getting Started Guide User Interface and Data Entry 3 The TerraSync software display The screen below shows elements that are common to all screens in the TerraSync software Section button Status bar Subsection button Form title 197 Road Sign MOK Cancel Buttons Date Visited B Field label Type Field value Condition Good kj Image file dd oK Pause Status bar The status bar appears at the top of the TerraSync software screen and provides basic status information about the connected GPS receiver For information about how to connect toa GPS receiver see Connecting to a GPS receiver page 48 B Data es SHY 20 as Satellite icon Logging icon Real time correction Estimated source icon accuracy icon Battery icon Filter icon The status bar is always visible but the icons displayed depend on the current status of the system Table 3 1 shows the icons that can appear Table 3 1 Status bar Icons Icon Name Description Satellite icon e 8 Shows whether the geometry of the satellites is good or bad as configured in the GPS settings area of the software The sat
59. tap Next to stop logging bearing from the reference position to the feature You can use data from a laser rangefinder See Using a laser rangefinder to record offsets page 182 f Tap Next to confirm the measurement for this reference position 4 Ifyou are recording an offset that uses distances enter the direction that the features lies in relative to the path between the reference positions The software calculates the position of the feature 5 When the offset form is complete tap OK The attribute entry form reappears Note Logging is paused because you only have to record positions for the reference positions not the feature itself 6 Record attributes for the feature and then tap OK to store the feature The Collect Features screen appears TerraSync Software Getting Started Guide 179 A Advanced Datalogging Options 180 Distance distance offset A distance distance offset uses the distance between the feature and two reference positions A and B to specify the position of the feature The feature lies at the point where the circles centered on A and B intersect Because there are two points where the circles intersect you need to specify which direction the feature is in relative to the path from A to B Feature B to feature a a fro 8 Distance from A to ere oat aet Triple distance offset A triple distance offset uses the distance between the feature and t
60. the distance from the reference position to the tree 116 TerraSync Software Getting Started Guide Tutorial Collecting Data 5 d Inthe Horizontal distance field enter the UES offset measurement You do not need to a F 530m Hy measure the Vertical distance so leave this at Collet the default of zero Triple Distance offset for 9 Tree T fi h f Enter the distance from reference ition 1 to the fee e ap Next to conlirm the measurement tor position e fez TER E this reference position Reference position 1 Collected 6 Move to the second reference position and then Distance A tap Resume This starts logging GPS positions for Horizontal distance 13 00 m the second reference position ide aetan oom 7 Repeat Step b through Step e 8 Move to the third reference position and then tap Resume 9 Repeat Step b through Step e 10 If prompted to confirm the relative direction of the feature from your reference positions tap Next 11 Once the offset is calculated tap OK 12 In the attribute entry form enter the attributes for the tree and then tap OK to save the feature and return to the Collect Features screen D Ending the data collection session When the data update session is complete exit the TerraSync software You do not have to close the data file first If you exit the software while a data file is still open the TerraSync software closes the file before
61. the fie id estimated accuracy 3 Use Accuracy based Logging Yes v From the Use Accuracy based Logging field Apply Accuracy based Logging To select Yes All Features i Required Accuracy 5m w From the Apply Accuracy based Logging To field select the feature types that will use accuracy based logging In the Required Accuracy field enter the accuracy you require Tap OK to save the accuracy based logging settings and return to the Logging Settings form TerraSync Software Getting Started Guide 161 6 162 High Accuracy Data Collection Collecting sufficient high accuracy data To start using data from the RTK receiver connect to GPS as usual The appropriate RTK icon appears in the status bar For example if the receiver is using its integrated RTK radio to receive corrections the integrated RTK radio icon g appears Once the receiver is connected it starts initializing RTK mode While the receiver is initializing the RTK icon flashes When the icon stops flashing RTK mode is initialized and you can start using positions from the receiver Tip Survey receivers are designed to initialize while moving Depending on the GPS constellation and the physical environment you are in moving around may decrease the time required to initialize However if you need to initialize in for example if the RTK communications link fails while you are logging a point feature moving around increases the initializa
62. the field ok Cancel Defaut Hep In the Type of Data to Import group select the Features with External Data Dictionary option c Click Dictionary File Browse for the Seaview ddf file select it and then click Open Select the Coordinate System tab and then click Change to change to the coordinate system the GIS data uses You must import GIS data using the same coordinate system that the GIS data is already stored in TerraSync Software Getting Started Guide 131 5 132 Tutorial Collecting Data i Make sure that Latitude Longitude is selected in the System field and that WGS 1984 is selected in the Datum field Make sure that the Height Above Ellipsoid option is selected in the Altitude Measured From group The settings should look the same as those shown Click OK to return to the Import Setup Properties dialog Select the Output tab In the Output group make x Coordinate System and Zone i Cancel Help System atitude Longitude v ECA Datum was 1984 x Spon Select By Altitude Measured From Height Above Ellipsoid HAE C Mean Sea Level MSL if G EGM36 Global zi Meter z Altitude Units Meters X sure that the Combine input files into one output file option is selected Click OK to return to the Import dialog 6 Click the Browse button beside the Output File field The Specify Output File dialog appears The default fi
63. the office computer To transfer files using do the following the Windows Mobile Device Center click File Management and use the Windows Explorer type window to copy files ActiveSync technology click Explore and use the Windows Explorer type window to copy files Step 4 Uninstall any previous versions of TerraSync software Before installing a new version of the TerraSync software Trimble recommends that you uninstall any previously installed versions of the TerraSync software from the Windows Mobile powered device and the office computer To remove programs do the following from the device using the Windows Mobile click Programs and Services and then click Device Center Add Remove Programs Tip If the Add Remove Programs option is not displayed below Programs and Services click More The Add Remove Programs option appears from the device using ActiveSync select Add Remove Programs from the Tools technology menu from the office computer use the Add or Remove Programs tool in the Control Panel Step 5 Check that you have enough space on the device Trimble recommends that you install the TerraSync software to an internal non volatile storage location if such a location is available This leaves more storage and program memory available on the device Note When installing software onto a Windows Mobile powered device you cannot install to RAM The default installation location is alway
64. to track visible satellites and to calculate its current position Note If the GPS receiver is new has not been used for some time or has been transported a substantial distance since last tracking satellites it may take up to 10 minutes before the latest satellite orbital position data ephemeris has been downloaded from the GPS constellation Until then the TerraSync software cannot display your position If the receiver is computing GPS positions the satellite icon in the Status bar and the number beside the icon are solid If the satellite or its number are flashing the satellite geometry is poor or there are too few satellites available to compute GPS positions Adjust the GPS slider bar see Configuring GPS quality settings page 99 or wait until conditions are more favorable Tip For more information about satellite geometry and how this can affect GPS data collection go to www trimble com gps TerraSync Software Getting Started Guide Tutorial Collecting Data 5 D Configuring the required logging accuracy In this tutorial the Seaview Authority is required to provide geographical positions with an accuracy of 5 meters or better Using the Accuracy Settings dialog in the TerraSync software you can prevent GPS positions that do not meet this accuracy requirement from being logged For the tutorial you will set a required horizontal postprocessed accuracy of five meters The TerraSync software calculates the predicted hor
65. track GPS status log new data and update existing data and navigate in the field The TerraSync software acts as the controlling software It communicates with a range of Trimble GPS receivers see Compatible GPS receivers page 47 connected to the field computer allowing you to set GPS parameters in the receiver record GPS positions on the field computer and update existing GIS data The software can be used with a wide variety of real time differential correction sources If the GPS receiver has an integrated receiver that allows it to receive real time correction messages from a real time differential correction source then the source can be used directly with the GPS receiver For example if your receiver has integrated support for Satellite Based Augmentation Systems SBAS such as WAAS EGNOS and MSAS then SBAS corrections can be used directly by the GPS receiver If your receiver is not able to receive these types of signals use an external source to receive the correction messages and provide them to the GPS receiver For example you can use an external receiver a radio link to an external data radio or use a cellphone to dial an Internet Service Provider and then download the corrections from an Internet server TerraSync Software Getting Started Guide Introduction 1 The TerraSync software provides mission planning in the field and data dictionary editing tools Trimble postprocessing software the GPS Pathfinder Office so
66. using the Bluetooth radio in a Windows Mobile powered field computer to connect to a Bluetooth enabled cellular phone and then connect to the Internet Note Some cellular phones support the Bluetooth PAN Personal Area Networking service as well as the Bluetooth DUN Dialup Networking service Because DUN connections are more common this section assumes you are making a dialup network connection with the Bluetooth enabled phone To connect to a Bluetooth enabled phone using a Bluetooth DUN Dialup Networking connection you must 1 If required connect the GPS receiver to the field computer 2 Connect the field computer to a Bluetooth enabled phone and then configure the connection to the dialup network 3 Connect to the Internet using the dialup network 4 Configure the TerraSync software to use real time corrections received from the Internet source Note Before you begin the steps below Trimble recommends that you confirm that the phone can access the Internet directly If necessary contact the cellular phone provider and confirm whether you must enter a user name password and domain details when connecting an external device to the phone using Bluetooth dialup networking Step 1 Connecting the GPS receiver to the field computer If you are not using a field computer that has an integrated GPS receiver connect the GPS receiver to the field computer For more information refer to the documentation provided with th
67. utilities Batch Processor 127 Connection Manager 127 Data Transfer 133 Export 126 UTM definition 220 V vector graphics definition 220 velocity definition 220 vertex definition 220 vertex logging icon 59 tooltip 61 vertex overview 111 184 viewing attributes in GPS Pathfinder Office 125 data files in GPS Pathfinder Office 125 features on the map 103 GIS data 125 GPS status 95 virtual keyboards 54 VRS network address format 168 defined 221 direct dial connection to 170 172 Internet connection to 165 169 real time correction tooltip 60 software 163 using corrections from 163 172 WwW WAAS 221 warning messages 74 waypoints 81 Web map server definition 221 WGS 84 definition 221 Windows Error Reporting 15 Windows Mobile Device Center 18 Windows Mobile operating system getting help 53 Windows Mobile powered device battery level 58 definition 221 locking 55 TerraSync Software Getting Started Guide 231 Index supported operating systems 18 switching between applications 53 troubleshooting 203 Windows Mobile version 5 0 software 37 43 Windows Mobile version 6 operating system 37 43 Windows supported operating systems 18 wireless LAN 165 Z zone changing 196 232 TerraSync Software Getting Started Guide NORTH amp SOUTH AMERICA Trimble Navigation Limited 10355 Westmoor Drive Suite 100 Westminster CO 80021 USA EUROPE amp AFRICA Trimble GmbH Am Prime Parc 11 65479 Raunheim GER
68. you double tap a feature and you are using the desktop version of the software your mouse pointer may be configured to snap to the default control Tone umber of Lanes This setting prevents double tapping from working ee aia correctly To disable this option select the Mouse option in RES E the Windows Control Panel select the Motion tab and then l clear the Snap mouse to default button in dialogs check box 3 All attribute values are correct so you do not have pe z Si to make any changes 4 Tap OK The attribute entry form closes and you are returned to the Map section When you change the attributes offset or GPS position of an existing feature the status of the feature automatically changes to Updated TerraSync Software Getting Started Guide Tutorial Collecting Data 5 a Navigating to a waypoint Remember the garbage can location you previously recorded as a waypoint in Exercise 2 In this exercise you will open the waypoint file you created earlier and then use the waypoint to navigate to the GPS position From this GPS position you will collect the garbage can feature that was installed by the work gang L 2 3 4 5 6 Note When you are within the specified close up range of the target the navigation proximity alarm sounds and then the Close up graphical screen replaces the Direction Dial screen Tap the Section list button and then select Navigation Tap the Subsection list button and then se
69. 0 00110 09182 A43216BD Software Maintenance Expiry Date 29 Jun 2010 Activated on Device Name gt Juno SC Handheld Activated on Device Serial Number 99100073466243 Activation Date gt 14 Dec 2009 s v Done Local intranet 100 10 Ifthe five lines below the TerraSync software do not appear click the beside the copy of the TerraSync software that you have just registered The Installation Code field shows the installation code for your copy of the TerraSync software Make a note of this code You must enter this code when you install or reinstall the software Note Ifyou are entitled to an upgrade from a previous version of the TerraSync software you can install TerraSync version 4 10 using the installation code that you obtained when you first registered the product Ifyou are not entitled to an upgrade the installation program will not accept your installation code Contact your local Trimble reseller to purchase a software maintenance option TerraSync Software Getting Started Guide 23 2 Software Installation and Activation Obtaining your installation code after registration To reinstall the TerraSync software for example if you performed a factory reset on the device or reinstalled the operating system you must use the same installation code that you received when you registered the software before installing it for the first time Ifyou do not know the installation code do one of the following e Ifso
70. 8 techinques compared 149 carrier phase measurements definition 211 carrier phase operation H Star 148 postprocessing 148 RTK 148 Cartesian coordinates 211 CEA value 59 cellular phone connecting to 165 167 centroid definition 211 changing coordinate system 196 checking equipment 93 Close up screen tutorial 141 closing TerraSync software 106 117 146 CMR message format definition 212 generating corrections in 199 CMR message format generating corrections in 199 Coarse Acquisition code definition 212 code phase definition 212 COGO for complex offsets 178 collecting area feature 103 line feature 102 new data tutorial 100 point feature 101 color in the TerraSync software 77 map layers 77 columns sorting 64 complex offsets overview 178 configuring carrier phase data collection 155 coordinate system 196 connect icon 57 tooltip 60 connecting to a Bluetooth enabled cellular phone 166 167 a VRS network 165 172 224 TerraSync Software Getting Started Guide an Internet server 165 169 Connection Control field 169 Connection Manager utility 127 Connection Method field 168 context sensitive Help accessing 52 continuing line and area features 113 continuing line and area features overview 175 coordinate geometry for complex offsets 178 coordinate system changing 196 configuring 196 Coordinate System Manager utility 193 default geoid in TerraSyne 193 defined 212 overview 190 transferring 195 types 190 coordi
71. 8GNSS receiver firmware version 3 00 or later There are advantages and disadvantages to each of these three techniques The following section contrasts and compares these techniques and outlines the equipment and infrastructure required to use each technique 148 TerraSync Software Getting Started Guide High Accuracy Data Collection 6 Carrier phase techniques compared H Star technology H Star technology offers an easy to use cost effective solution for obtaining data with subfoot accuracy or better Pros Cons Subfoot accuracy or better in real time or after postprocessing with only two minutes of carrier data Unlike other types of data collection positions are usable in less than two minutes although they may not be subfoot Accuracy achieveable over longer baselines than when using carrier phase postprocessing or RTK Moderately priced field equipment Potential to leverage public base station infrastructure and thereby avoid any direct infrastructure cost Areas where public base station infrastructure does not exist will require infrastructure investment to achieve subfoot accuracy Requires a period of uninterrupted carrier logging typically two minutes or less to achieve subfoot accuracy In tough GPS environments where satellite signals are interrupted for example high multipath or under tree canopy the required two minutes of carrier lock may be unattainable Carrier phase postprocessing Car
72. Accuracy Data Collection 6 When you start a new feature that is set to carrier accuracy the logging icon appears in the Status bar When the TerraSync software has logged carrier phase data continuously for the minimum time 10 minutes the success beep sounds If you try to close a file before the minimum time is up _ Number of Lanes F the TerraSync software asks you to confirm that you Su Asphalt want to close the file If you do close the file you may Condition lose carrier accuracy for some features Once the counter is running you can choose to end the current feature and stay where you are until the minimum time is up When the success beep sounds move to the next feature Using this method you can be sure that you have sufficient data to generate precise positions OK Tog Alternatively if you think you are unlikely to lose lock you can move to the next feature before sufficient carrier phase data has been collected This is possible because all features recorded during a block achieve the precision associated with that block Provided that a block eventually contains enough useful data you can generate precise positions for any feature recorded within it CAUTION Do not move to the next feature before the minimum time is up unless you are sure that you will not lose lock The Estimated Accuracy icon shows a prediction of the accuracy that will be achiev
73. California United States gis_j yahoo com To update your information or change your password Click Edit If you are an employee of a company who sells supports trains or services Trimble products you can click here to request access to Trimble Store or Partners Manage Communications Update Subscribe to Newsletters and Warranty Expiration Notifications Order Demo Cds You are subscribed to the following Nothing is selected Please click Update to add details My Products Nothing has been registered yet Please click Add to register your products Local intranet 4 To register the TerraSync software scroll to the My Products section and then click Add The Registration Method page appears Home Windows Internet Explorer E http support trimble com CPRS Home aspx E 5 x cook View Favorites Tools Help gt Bl me E eae s G Tos GIS s Profile Logout Add New Product Registration Method Please select the method you will be using to add your product then click Next to proceed O Add a new serial number The serial number is usually found on a label attached to your hardware device or in the About box from the Help menu of your software Serial number values often appear next to a bar code or have SN immediately before the value Add a Proof of Purchase Number POPN Proof Of Purchase Numbers or POPNs are supplied with recent versions of Trimble Mapp
74. Critical Stop event TerraSync Software Getting Started Guide 75 3 76 User Interface and Data Entry Event Sound Description category Question System The TerraSync software requires some information or a Dead GPS battery Warning Low GPS battery Warning Poor geometry Warning Real time lost Warning Too few satellites Warning Carrier lock lost Warning Required accuracy Warning lost decision from you The question appears in a message and is indicated by the sound the field computer uses for the Question event The battery in use by the GPS receiver is dead The TerraSync software continues to operate but no position information is received until the battery is replaced This sound plays repeatedly and the battery icon in the status bar flashes when the battery in use by the GPS receiver is running low and needs to be replaced GPS position quality has dropped below the level you have specified because the visible satellites are too close together in the sky The TerraSync software has paused logging until geometry improves The connection to the specified source of real time differential correction has been lost GPS position quality has dropped below the level you have specified because there are not enough visible satellites The TerraSync software has paused logging until more satellites become visible Carrier lock has been lost The TerraSync software has stopped logging carrier or H Star data
75. Data collection page 94 D Exercise 3 Advanced data collection page 107 optional Exercise 4 Processing the data page 118 Data update Exercise 5 Preparing for data update page 128 D Exercise 6 Data update page 135 TerraSync Software Getting Started Guide Tutorial Collecting Data 5 Tutorial scenario The tutorial is based on the following scenario The Seaview Authority maintains a GIS of its street signs streets and neighborhood parks for inventory purposes Information needs to be collected about each entity indicating its condition and other important information You and your field crew are responsible for collecting new data and updating the existing GIS data for Starfish Bay Lamp Posts Stop Sign Seagull Street Seaweed Street Squid Way Sand Box Concrete Oyster Lane Asphalt Trash Can Data collection In this part of the tutorial you collect new features First you create a GPS Pathfinder Office software project and prepare your equipment for data collection Then you go to Starfish Bay where you record new features and their attributes When you return to the office you postprocess the data you collected to achieve better positional accuracy for your results Then you export the data to the Seaview Authority GIS The data collection part of the tutorial begins on page 94 Data update In this part of the tutorial you update existing GIS data Some time has passed since yo
76. Eb ew wa eo ee ee 198 Generating real time corrections 2 1 ee ee eee 199 Unattended base station sessa et othe Seepage Ge de a gale be Oe ge 200 Troubleshooting 2 2 2 22 E a eee eee 201 COMMUMICALIONS 4 505 oe Se REE sR EA RGR Se ee RG Ra ea OE ne Bess 202 FieldicOmputer ii cu ahs Ado bath ee all a be crab a ead ed a eae oo hoe does 203 PDs io oe e CRSA hee CREA Oe OF OTHER OSs BRK aS SSRs SOSA 204 Real time differential correction 2 0 eee ees 205 Data MES karain rene as teak ergs Gaeta oS Geeta Meike sted dee ga ets gaged S 206 Map sheen s e hi ckc chee week pE Pad ew RR ee ee a a ee eR ee dA 207 Coordinate system sia a anc cba ea WA ec a Va ea Pe eA 208 Posion accuracy sigs t eee RR RE Se Se wR OR a E ee Ee Ee en lS 209 Glossary oe 6S 4 SOS 6S SS SHEE TOE FOS 6404596446452 85 211 NUK cee keen ee hee thee eee oe eG ee See 223 TerraSync Software Getting Started Guide Introduction In this chapter Documentation conventions About the TerraSync software TerraSync software editions Finding additional information Technical assistance Your comments CHAPTER Welcome to the TerraSync Software Getting Started Guide This guide provides e an overview of the Trimble TerraSync software e atutorial on using the TerraSync software e a guide to the user interface and general operation of the TerraSync software Even if you have used other Global Positioning System GPS products before Trimbl
77. Features h Required Accuracy 5m x Tap OK to save the settings and return to the Logging Settings form Opening an existing data file Before starting the data update session open the file that contains the GIS data Use the Data section to do this To open an existing file L 2 3 Tap the Section list button and then select Data Tap the Subsection list button and then select Existing File Select the Starfish file This is the file that you imported earlier from the Seaview Authority GIS Tap Open The Confirm Antenna Height dialog appears Click OK The Update Features screen appears This screen shows a list of all existing features in the data file Now that you have opened a data file you can start updating features TerraSync Software Getting Started Guide File Starfish Choose Feature Bein Oyster Lane Seaweed Street Positions 0 Length 2D 3D Name 1 Condition Filtering features Tutorial Collecting Data 5 Your first task is to locate any traffic signs that need to be replaced by your field crew To make it easy to see which signs you must visit you will use filtering to group the features that must be updated and then select the features you want from the filtered group You can filter features by their e update status e deletion status e feature type attribute values The road signs you want to filter have the value
78. For real time H Star technology the corrections are calculated from information recorded in the network of base stations by the VRS server and transmitted to the receiver For postprocessed H Star technology each GPS position is corrected using data from each base station in the group and then the results are averaged The averaging calculation gives more weight to base stations that are closer to where the original GPS positions were collected and cancels out bias errors Required infrastructure for H Star technology A receiver capable of real time H Star technology uses base station data from a VRS or a single nearby within 80 km base station to generate H Star positions in the field For real time H Star operation a wireless data link is required between the roving GPS receiver and either a nearby base station or a VRS network For postprocessed data to achieve subfoot accuracy three or more good quality dual frequency L1 L2 base stations within 200 km are required Alternatively one good quality dual frequency base station within 80 km is required The coordinate of each base station must be in the same coordinate system datum and reference frame Furthermore if a base station has coordinates in terms of ITRF2000 but your GIS is in terms of NAD83 this can introduce up to a meter of error unless transformed during the Export process TerraSync Software Getting Started Guide High Accuracy Data Collection 6 Configuring the T
79. Guide 63 3 User Interface and Data Entry e Press Tab on the physical keyboard Press Tab repeatedly to move through all fields on the form To move up or down the form drag the vertical scroll bar When you finish browsing through the form or finish editing fields in the form tap OK to accept the changes you made and to return to the previous screen Lists Some forms in the TerraSync software include lists from which you select data files or features A list contains the information that is currently stored Each row of the list represents one file or feature Each column shows information about that item A list also has a label that describes its contents This figure shows the Choose Feature list which displays all feature types in the open data file File Sample Label choose Feature Column heading Rivet St Reserve Warwick Park Cove Park Potomska St Potomska St John F Kennedy M6 John F Kennedy M6 CT fields Name Potomska St Number of Lanes 2 Often information fields are displayed at the bottom of the screen below the list They provide useful information about the item currently selected in the list f A Positions 2 Information Length 2D 2981m 3D 29 81 m To choose an item from a list select the item If the item you want is not visible drag the vertical scroll bar up or down until it is visible Tap a column heading to sort items by that column For example t
80. I Shapefile Setup v Format ESRI Shapefile Type of Import Features with External Data Dictionary Output Option Combine input files into one output file GIS Coordinate System Site System Latitude Longitude Zone Datum WGS 1984 Coordinate Units New Delete Properties The Shapefiles that you exported at the end of the data collection part of the tutorial appear in the Selected Files list If they do not appear click Browse and locate the folder GPS Projects TerraSync Tutorial Export Select the files and then click Open From the Choose an Import Setup drop down list make sure that Sample ESRI Shapefile Setup is selected TerraSync Software Getting Started Guide Tutorial Collecting Data 5 5 Change the import setup properties a Click Properties The Import Setup Properties Sample ESRI Shapefile Setup dialog appears Make sure that the Data tab is selected Import Setup Properties Sample ESRI Shapefile Setup Data ESRI Shapefile Coordinate System Output Type of Data to Import C Features with Data Dictionary Data Dictionary File Only Features with Extemal Data Dictionary Select Data Dictionary CA Seaview daf Tip This option matches feature and attribute names from the GIS with the feature and attribute definitions in the selected data dictionary It is recommended that you use this option when you intend to update any attribute data or collect new features in
81. LL TRIMBLE OR ITS SUPPLIERS BE LIABLE FOR ANY SPECIAL INCIDENTAL INDIRECT OR CONSEQUENTIAL OR PUNITIVE DAMAGES HOWEVER CAUSED AND REGARDLESS OF THE THEORY OF LIABILITY INCLUDING WITHOUT LIMITATION DAMAGES FOR LOSS OF BUSINESS PROFITS BUSINESS INTERRUPTION LOSS OF BUSINESS INFORMATION OR ANY OTHER PECUNIARY LOSS ARISING OUT OF THE USE OR INABILITY TO USE THE SOFTWARE OR THE PROVISION OF OR FAILURE TO PROVIDE SUPPORT SERVICES EVEN IF TRIMBLE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES AND NOTWITHSTANDING ANY FAILURE OF ESSENTIAL PURPOSE OF ANY EXCLUSIVE REMEDY PROVIDED IN THIS AGREEMENT IN NO EVENT SHALL TRIMBLE S TOTAL LIABILITY IN CONNECTION WITH THIS AGREEMENT OR THE SOFTWARE WHETHER BASED ON CONTRACT WARRANTY TORT INCLUDING NEGLIGENCE EXCEED THE ACTUAL AMOUNT PAID TO TRIMBLE FOR USE OF THE SOFTWARE GIVING RISE TO THE CLAIM BECAUSE SOME STATES AND JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES THE ABOVE LIMITATION MAY NOT APPLY TO YOU 3 5 PLEASE NOTE THE ABOVE TRIMBLE LIMITED WARRANTY PROVISIONS MAY NOT APPLY TO SOFTWARE PRODUCTS PURCHASED IN THOSE JURISDICTIONS SUCH AS COUNTRIES OF THE EUROPEAN ECONOMIC COMMUNITY IN WHICH PRODUCT WARRANTIES ARE OBTAINED FROM THE LOCAL DISTRIBUTOR IN SUCH CASE PLEASE CONTACT YOUR TRIMBLE DEALER FOR APPLICABLE WARRANTY INFORMATION 4 GENERAL 4 1 This Agreement shall be governed by the laws of the State of Calif
82. MANY ASIA PACIFIC amp MIDDLE EAST Trimble Navigation Singapore PTE Limited 80 Marine Parade Road 22 06 Parkway Parade Singapore 449269 SINGAPORE Trimble www trimble com
83. NTRIP server is an example of a broadcast server See code phase Carrier phase is the time taken for the L1 or L2 carrier signal generated by the satellite to reach the GPS receiver Measuring the number of carrier waves between the satellite and receiver is a very accurate method of calculating the distance between them The Cartesian coordinate system is a system of coordinates that defines the location of a point in space in terms of its perpendicular distance from each of a set of mutually perpendicular axes The X direction is 0 latitude the Greenwich meridian and the Y direction is 90 east longitude The calculated center of an area feature TerraSync Software Getting Started Guide 211 Glossary CMR Coarse Acquisition code code phase coordinate system cross track error cross track line data dictionary datum datum transformation declination DGPS Compact Measurement Record A real time message format developed by Trimble for broadcasting corrections to other Trimble receivers CMR is a more efficient alternative to RTCM correction messages but is not supported by all non Trimble receivers See code phase also known as Coarse Acquisition code or C A code The difference between the pseudo random number code generated by the TerraSync software and the pseudorandom number code coming in from the satellite The code phase data is used to quickly compute the distance to a satellite and therefor
84. OP is a measure of the quality of GPS positions based on the geometry of the satellites used to compute the positions When satellites are widely spaced relative to each other the DOP value is lower and position accuracy is greater When satellites are close together in the sky the DOP is higher and GPS positions may contain a greater level of error HDOP is a DOP value that indicates the accuracy of horizontal measurements Other DOP values include VDOP vertical DOP and PDOP Position DOP The TerraSync software lets you specify either a maximum HDOP value or a maximum PDOP It uses this maximum value as an upper bound on DOP values You can configure the desired level of accuracy and make sure that the positions logged are of a certain quality When the DOP exceeds this maximum the TerraSync software stops computing GPS positions Using a maximum HDOP is ideal for situations where vertical precision is not particularly important and your position yield would be decreased by the vertical component of the PDOP for example if you are collecting data under canopy H Star technology is a Trimble patented technology allowing the collection of high accuracy GPS data A GPS receiver that has H Star technology logs L1 data or if used with an external dual frequency antenna logs L1 and L2 data Real time H Star technology uses corrections from an external source to provide decimeter accuracy in the field Postprocessed H Star technology uses
85. Repeat to efficiently record a sequence of similar features When you use Repeat attribute values are copied from the last recorded feature of the same type You do not have to re enter values for all attributes Just check that each attribute value is correct for the new feature and change only those that are different To repeat attributes for similar features 1 From the Collect Features screen tap Options and then select Repeat When Repeat is selected a check mark V appears beside it in the option list 2 Select a feature from the Choose Feature list and then tap Create The attribute entry form appears The attribute values that appear are those of the last recorded feature of that type Edit them if necessary Tap OK to save the attribute values and store the feature 3 Select another feature Continue until you want to turn off Repeat mode To turn off Repeat mode e From the Collect Features screen tap Options and then select Repeat The check mark disappears Note When Repeat is not selected the data dictionary determines default attribute values Where appropriate the data dictionary specifies a default value for each attribute of a feature Segmenting line features Use segmenting to record a line as several segments that are joined together each with different attribute values For example you can record a road feature that has one surface for part of its length and a different surface for the rest of its leng
86. Started Guide Software Installation and Activation 2 Install Microsoft connection management software onto the office computer Connect the Windows Mobile powered device and the computer Back up any TerraSync software data files Uninstall any previously installed versions of the TerraSync software ao fF OO Check that you have enough space on the device to install version 4 10 of the TerraSync software a Install version 4 10 of the TerraSync software 7 Ifnecessary install the appropriate font if you have installed a translated version of the TerraSync software More information about each step is provided below Step 1 Install Microsoft connection management software onto the computer Note You must install the Windows Mobile Device Center or ActiveSync technology onto the computer before you connect the device To install software onto a Windows Mobile powered device you must connect the device to the office computer If the computer is running e the Windows Vista or Windows 7 operating system use the Windows Mobile Device Center to manage the connection e the Windows XP operating system use Microsoft ActiveSync technology to manage the connection Installing the Windows Mobile Device Center The Windows Vista and Windows 7 operating systems include a basic connectivity driver for Windows Mobile powered devices This driver allows you to transfer files from the device to your PC To install softwa
87. Started Guide 111 5 Tutorial Collecting Data 10 11 12 13 Tap Options select Nest and then select Light Pole Walk up to the light pole and then tap Log In the attribute entry form enter the attributes for the light pole Once you collect sufficient positions for the light pole tap OK to return to the Seaweed Street attribute entry form Return to the line you were walking when collecting Seaweed Street and then tap Resume Continue along Seaweed Street until you reach the next light pole and then tap Pause lerraSync Offset New Vertex Logging Interval Traffic r Light Pole Tab a capfalsfal To hT A AA ca J he OK Ea Pause Repeat Step 7 through Step 11 to log the remaining light poles At the end of Seaweed Street tap OK to save the Seaweed Street feature and return to the Collect Features screen 112 TerraSync Software Getting Started Guide Tutorial Collecting Data 5 Collecting an area feature while collecting a line feature continuation You need to collect a new line feature for Squid Way that also has a new nearby duck pond When recording Squid Way you will pass the new pond that you also need to record To save time and avoid traveling back to the pond you will log the line feature pause and record the area feature and then continue recording the line feature Note You can collect as many features within a line or area as you need The nu
88. T IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT PROMPTLY RETURN THE UNUSED SOFTWARE AND ANY ACCOMPANYING TRIMBLE PRODUCT TO THE PLACE FROM WHICH YOU OBTAINED THEM FOR A REFUND This Software is protected by copyright laws and international copyright treaties as well as other intellectual property laws and reaties The Software is licensed not sold Third Party Software The following third party software is or may be included with the Software and is subject to this Agreement ECW JPEG 2000 Runtime copyright 2006 Earth Resource Mapping Limited All rights reserved MrSID Decoder Runtime copyright 1995 1999 LizardTech Inc All rights reserved The U S Government has reserved rights to the MrSID technology as described in Section 5 below SOFTWARE PRODUCT LICENSE 1 1 License Grant Subject to the terms and conditions of this Agreement and your payment of applicable license fees Trimble grants you a non exclusive non transferable except as expressly provided below license right to install activate and use one 1 copy of the Software in machine readable form on any computer 4 TerraSync Software Getting Started Guide hardware and operating system for which it was intended for your internal business needs Your activation of the Software shall be effected in accordance with Trimble s usual and customary activation procedures current on the date of activation You may use the Software on only one computer at
89. a 1 ee ee eee 156 Carrier phase postprocessing workflow and required infrastructure 158 Required infrastructure for carrier phase data 0 00000 eee 158 Collecting sufficient high accuracy data 1 0 ee ee eee 158 Real time kinematic workflow and required infrastructure 00 0000 0 160 Required infrastructure for RTK 1 0 2 eee ee eee 160 Configuring the TerraSync software for RTK data collection 160 Collecting sufficient high accuracy data 1 0 ee eee 162 Using corrections froma VRS network 1 eee 163 Connecting to a VRS network using an Internet connection 165 Connecting to a VRS network using a direct dialconnection 170 Advanced Datalogging Options 0 00 e eee eee 173 Log Now and Lop Later sic ne ack ye We he ee ee ae Wee ew Ae Boke eo 174 Recording between feature positions 2 ee ee eee 174 Continuing line and area features 1 ee eee 175 OUSCUS e Ny teats eae be OG bas e e e Pie Aly oo tbe es v4 oe ble Poe 176 Complex offsets gcei dss Ko eal a Beg oe be AeA ae eis Vo alae cele bead 178 TerraSync Software Getting Started Guide 9 Contents 10 Recording a complex offset eee 179 Distance distance offset ee 180 Bearing bearing Offset sonsa saai ede Ae a wad a we Gal a ate ee 181 Triple bearing offset cc pusiiv as da tip i Hides oh eA OG Rade we da Shes 181 Using a laser rangefinde
90. a Windows Mobile powered device you cannot install to main memory The default installation location is the device s internal non volatile disk If the device has a non volatile internal storage location this is used as the default installation location even if you choose to install to main memory Internal storage locations include the Disk on a GeoExplorer 2003 series handheld and the Built In Storage on a Trimble Recon handheld running Windows Mobile 2003 software If the device has no non volatile storage or has only removable secondary storage such as a CompactFlash card the default installation location is the main memory RAM Note If an SD Secure Digital memory card is inserted in the handheld the card appears as an installation location option Trimble recommends that you install software to the handhelds internal storage not to an SD memory card If you install software to a card and then remove the card from the handheld the software will not be available for Use 14 15 If you clicked No in Step 13 the Select Destination Media dialog appears Click OK to proceed with the installation On some Windows Mobile powered devices such as the Trimble Recon handheld the message Adding information for Remove Programs may remain on the screen for several minutes Do not cancel the installation or reset the device while this message is displayed When you install the TerraSync software on a device powered
91. a line feature and a park is an area feature Features are defined in a data dictionary In the TerraSync software documentation a field computer is any portable computer such as a handheld device a laptop or a Tablet PC running the TerraSync software See also Windows Mobile powered device A geoid is an imaginary three dimensional surface representing Mean Sea Level MSL if it was projected to extend through the continents Unlike an ellipsoid or datum which have a symmetrical surface the geoid undulates perpendicular to the force of gravity For more information see Modelling the earth s surface page 188 TerraSync Software Getting Started Guide 213 Glossary geoid height geoid model great circle distance guest HAE HDOP heading Height Above Ellipsoid horizon Also known as geoid separation and geoidal undulation The geoid height is the distance of the geoid MSL above or below the reference ellipsoid A geoid model is a mathematical representation of the geoid for a specific area or for the whole earth The great circle distance is the shortest distance between two points on the surface of a sphere A guest connection lets a Windows Mobile powered device exchange and share information with a desktop computer You need a guest connection or a partnership to transfer data between the TerraSync software on the device and the GPS Pathfinder Office software on the desktop computer When you connec
92. a problem and needs to close you are asked whether you wish to send an error report to Microsoft Trimble recommends that you click Send and then click any subsequent links that are used to obtain additional information Trimble can access the report that is sent to Microsoft and use it to improve the TerraSync software Your comments Your feedback about the supporting documentation helps us to improve it with each revision Email your comments to ReaderFeedback trimble com TerraSync Software Getting Started Guide 15 1 Introduction 16 TerraSync Software Getting Started Guide CHAPTER Software Installation and Activation In this chapter System requirements Registering the TerraSync software Installing the TerraSync software Activating the TerraSync software Updating the TerraSync software Compatible GPS receivers This chapter describes how to install version 4 10 of the TerraSync software onto a Windows Mobile powered device or onto an office computer that is running a Windows operating system It also describes how to activate the software ona handheld powered by the Windows Mobile version 5 0 software or version 6 operating system To install and run the TerraSync software you must 1 Make sure your field or office computer meets the minimum platform requirements for successful operation of the TerraSync software 2 Register your copy of the TerraSync software and obtain an installation code
93. a update session is complete exit the TerraSync software You do not have to close the data file first If you exit the software while a data file is still open the TerraSync software closes the file before exiting To exit the TerraSync software 1 Tap EJ in the upper right corner of the screen 2 When prompted to confirm closing the file and exiting the software tap Yes TerraSync Software Getting Started Guide CHAPTER High Accuracy Data Collection In this chapter This chapter contains detailed information about using high accuracy data collection methods to Introduction to carrier phase GPS achieve more accurate GPS positions m Carrier phase techniques compared m H Star technology workflow and required infrastructure m Carrier phase postprocessing workflow and required infrastructure m Real time kinematic workflow and required infrastructure m Using corrections from a VRS network TerraSync Software Getting Started Guide 147 6 High Accuracy Data Collection Introduction to carrier phase GPS To achieve high accuracy for GPS positions you need to use carrier phase data collection methods Normally GPS positions are calculated using code phase measurements how long it takes for the unique code generated by each satellite to reach the receiver For greater accuracy you can use the carrier signal that the PRN code is carried on Carrier phase measurements are much more accurate because the carrier sign
94. ackground Files Layer Formatting End Measurement Create End Feature Log Pause Resume TerraSync Software Getting Started Guide 83 4 Software Structure Data section New File Create Existing Open File Update Update Options Show Filtered Features Features Features Show Unfiltered Form Features Filter Delete Undelete Set Nav Start GPS Selected feature Set Nav Target Selected feature Construct Clear Nav Targets Logging Interval Continue View Number Name Label 1 Label 2 Update Filter Distance Attribute Options Offset Distance Bearing Entry Form Distance Distance Triple Distance Bearing Bearing Triple Bearing New Vertex Logging Interval Nest Segment Line Log Pause Resume External Trigger Log Pause Resume 84 TerraSync Software Getting Started Guide Software Structure 4 Collect Collect Options Logging Interval Features Features Repeat Form Log Now Log Later Continue Attribute Options Offset Distance Bearing Entry Form Distance Distance Triple Distance Bearing Bearing Triple Bearing New Vertex Logging Interval Nest Segment Line Log Pause Resume External Trigger Log Pause Resume File Options Delete Manager Copy to Default SD Card Rename Move to SD Card Send via Email Receive via Email Edit embedded dictionary New dictionary Read dictionary from data Read data from Shape Write data to Shape Extract data from file TerraSync Software Getting Started Gui
95. acy 5m ig d From the Apply Accuracy based Logging To field select the feature types that will use accuracy based logging e Inthe Required Accuracy field enter the accuracy you require f Tap OK to save the accuracy based logging settings and return to the Logging Settings form Note If your GPS receiver is not H Star capable the Auto setting corresponds to No Select No if you have a GPS receiver that is H Star capable but you do not want to log H Star data 10 Tap OK to close the Logging Settings form and confirm the changes you have made TerraSync Software Getting Started Guide 155 6 156 High Accuracy Data Collection For postprocessed H Star technology L 2 3 4 Tap the Section list button and then select Setup Tap Logging Settings The Logging Settings form appears Make sure that the Log Carrier Data field is set to Auto To use accuracy based logging a Tap the Setup button 7 below the Accuracy x wm lerraSync Settings field The Accuracy Settings form iR appears b From the Accuracy Value for Display Logging Aecuacy Settings _OK Cancel 2 fields select Postprocessed and whether the TerraSync software should calculate the estimated horizontal or vertical accuracy Accuracy Value For Display Logging Horizontal z Postprocessed v Postprocessing Base Distance c Ifyou selected In the off
96. al has a higher frequency than the PRN code resulting in smaller measurement errors The disadvantage is that in difficult environments carrier phase measurements are more difficult to collect than code measurements The TerraSync software supports three different kinds of carrier phase operation e H Star technology provides subfoot accuracy or better in real time or after postprocessing with as little as two minutes of carrier data Receivers capable of real time H Star operation are GPS Pathfinder ProXRT receiver GeoExplorer GeoXH handheld 2008 series Receivers capable of postprocessed H Star operation are GPS Pathfinder ProXRT receiver GPS Pathfinder ProXH receiver GeoExplorer GeoXH handheld 2005 and 2008 series e Carrier postprocessing provides accuracies ranging from 30 cm down to 1 cm with carrier data spanning from 10 minutes up to 45 minutes This technique is supported by many mid and high end Mapping amp GIS receivers including GPS Pathfinder ProXH and ProXT receivers GeoExplorer GeoXT handheld 2005 series and earlier GPS Pathfinder Pro XR and Pro XRS receivers GPS Pathfinder Power receiver e Real time kinematic RTK techniques using Survey equipment provide accuracies in the centimeter sub inch range in real time You can use RTK with the following Trimble survey receivers 5800 receiver firmware version 2 23 or later R8 receiver firmware version 2 23 or later R
97. all features in the layer TerraSync Software Getting Started Guide 77 3 User Interface and Data Entry To select layer colors tap Layers in the Map graphical screen and select Layer Formatting The Layer Formatting form appears You can set each layer to display in a different color You can also set two or more layers to the same color 78 TerraSync Software Getting Started Guide Software Structure In this chapter Introduction Sections Panes Section structure Section structure lists CHAPTER This chapter describes the main sections of the TerraSync software and provides an overview of the functionality provided by each section TerraSync Software Getting Started Guide 79 4 Software Structure Introduction The TerraSync software is arranged in the following five sections H Map Section icon Ea Data Section name Ld ee Section list Navigation button Status a Setup Navigation aoe ist One of these sections is always active and Status visible The Section list button shows the of Setup section that is currently active You can move between sections at any time without closing any open forms or screens To switch to a different section tap the Section list button and then select the section you want from the drop down list For example to switch from the Map section to the Data section tap the Section list button and then select E Data The button no
98. allation The Time Limited Software contains a disabling mechanism which will prevent the Time Limited Software from functioning after the end of the limited term In the event that you subsequently acquire a paid license to the Software then your continued use of the Software will be governed by the terms of this Agreement except for this Section 2 Resale or other distribution of Time Limited Software is prohibited 2 2 No Warranties YOU EXPRESSLY ACKNOWLEDGE AND AGREE THAT THE TIME LIMITED SOFTWARE IS PROVIDED TO YOU AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE NONINTERFERENCE TITLE AND NONINFRINGEMENT YOU ASSUME ALL RISK AS TO THE QUALITY AND PERFORMANCE OF THE TIME LIMITED SOFTWARE 3 LIMITED WARRANTY 3 1 Limited Warranty Trimble warrants that the Software will perform substantially in accordance with the accompanying written materials i e applicable user s guide or product manual for a period of either 90 days for TerraSync Standard edition or one 1 year for TerraSync Professional edition from the date of purchase of your license hereunder This limited warranty gives you specific legal rights you may have others which vary from state jurisdiction to state jurisdiction The above limited warranty does not apply to error corrections updates or upgrades of the Software after expiration of the lim
99. allation To run the rest of the TerraSync software in a language other than English after installing the software you must download the appropriate language update from www trimble com terrasync_ts asp For more information see Step 14 below Click Next The TerraSync software installation wizard appears Click Next Read the software license agreement and then click Yes to accept it TerraSync Software Getting Started Guide 45 2 Software Installation and Activation The Register your Software page appears TerraSync Desktop InstallShield Wizard Register your software To install TerraSyne you must enter a valid Installation Code To obtain an Installation Code use the proof of purchase number to register your copy of the software over the Internet The proof of purchase number is displayed on the TerraSyne CD packaging You must connect to the Internet to register If you do not have Internet access contact your Trimble dealer have already registered and have a valid Installation Code O I do not have an Installation Code want to register my copy over the Internet now 9 Doone of the following Ifyou have registered the software and obtained your installation code for the software select the J have already registered option and then click Next Ifyou have not yet registered the software and do not have an installation code for the software select the J do not have an installation code I
100. also lost when you disconnect from the receiver or turn off the receiver When lock is lost the TerraSync software displays a notification message and adjusts any accuracy estimates to reflect the degradation in accuracy due to loss of lock In difficult conditions code processing may be better than carrier techniques Initialization For RTK carrier lock must be achieved and maintained on five satellites until the receiver can generated a fixed carrier solution This process is known as initialization On today s RTK receivers it can be less then 10 seconds with a short baseline and open sky conditions On older receivers initialization may take a few minutes While carrier lock is maintained centimeter level accuracy is also maintained When carrier lock is lost the receiver must re initialize During initialization no positions are output from the survey RTK receiver Carrier blocks For postprocessing techniques the TerraSync software records blocks of carrier data throughout the data file Carrier blocks are periods of carrier phase logging over which carrier lock is maintained Figure 6 1 on page 152 shows how the number of satellites being continuously tracked affects the length of the carrier blocks TerraSync Software Getting Started Guide 151 6 High Accuracy Data Collection nn gt n O oO Q E 2 15 20 25 30 35 40 45 50 Time in minutes 5 or more satellites useful carrier phase data lock is los
101. anese Korean or Russian TerraSync software on an English or other foreign Windows Mobile powered device does not recognize Asian or Cyrillic characters entered using a keyboard This is because the English device cannot convert the Unicode characters to multi byte characters However Japanese TerraSync software running on a Japanese Windows Mobile powered device recognizes Japanese characters correctly Cyrillic characters from data dictionaries created in the GPS Pathfinder Office software using Russian Windows are not displayed correctly in Russian TerraSync software However this text displays correctly when transferred back to the GPS Pathfinder Office software Data dictionaries created in the GPS Pathfinder Office software using Chinese Japanese or Korean Windows are displayed properly Tip The Trimble GPS Pathfinder font is installed automatically when you install the TerraSync software This font includes symbols that you can use to represent point features on the map If you want to use other symbol fonts for point features install the additional fonts manually To install a TerraSync language font onto a Windows Mobile powered device 1 Uninstall any previous versions of the font CAUTION On some Windows Mobile powered devices you cannot delete Asian language fonts in the usual way To remove such fonts you may need to perform a hard reset of the device A hard reset removes all software that is not pre installed on the
102. arty to copy decompile disassemble or otherwise reverse engineer the Software or attempt to do so provided however that to the extent any applicable mandatory laws give you the right to perform any of the aforementioned activities without Trimble s consent in order to gain certain information about the Software for purposes specified in the respective statutes e g interoperability you hereby agree that before exercising any such rights you shall first request such information from Trimble in writing detailing the purpose for which you need the information Only if and after Trimble at its sole discretion partly or completely denies your request may you exercise such statutory rights 3 The Software is licensed as a single product You may not separate its component parts for use on more than one computer except as specifically authorized in this Agreement 4 You may not rent lease or lend the Software unless you are a reseller of Trimble products under separate written agreement with Trimble and authorized by Trimble to do so 5 No service bureau work is permitted For purposes of this Agreement service bureau work shall be deemed to include without limitation use of the Software to process or to generate output data for the benefit of or for purposes of rendering services to any third party over the Internet or other communications network 6 You may permanently transfer all of your rights under this Agreement provi
103. at is running on a Windows Mobile powered device 1 On the Windows Mobile taskbar tap E 2 Select Settings System Task Manager 3 Doone of the following TerraSync Software Getting Started Guide 53 3 54 User Interface and Data Entry e Toenda task select the the task you want to end BOPT and then tap End Task Application TerraSync e Toswitch to another task select the task you want Activesync fm Pictures amp Videos to switch to and then tap Menu Switch To sre Capture M Task Manager 4 Tap E to close the Task Manager dialog When the TerraSync software is already running on a Switch To device tapping EA Programs TerraSync does not start End All Tasks the software a second time Instead the TerraSync oni software becomes the active program Use this method a to switch back to the TerraSync software from another Exit application End Task Es Tip Some devices have hardware buttons that start specific applications You may be able to change the program that is assigned to a particular button or you can delete the existing program assignment so that pressing the button has no effect Removing or changing hardware button assignments can be helpful if you frequently activate hardware buttons by accident On screen keyboards vv a Some devices do not have a physical keyboard Instead enter text using an on screen keyboard To activate an on screen keyboard tap the
104. ation code that you must enter during installation For more information see Registering the TerraSync software page 19 the TerraSync software is not running on the device you have closed all applications on the device 2 Insert the TerraSync Software CD into the CD drive of the office computer Alternatively if you are entitled to an upgrade from a previous version of the TerraSync to version 4 10 you can download the software from www trimble com terrasync_ts asp Click Downloads and then click v4 10 Software The Setup screen appears S TerraSync ey a Trimble TerraSynce software Version 4 10 Main Menu Install Register Read documentation www trimble com 1995 2009 Trimble Navigation Limited All rights reserved This product is protected by US and international copyright trademark and patent laws as described in Status About Note If this screen does not appear select Autorun exe from the CD drive folder 3 Click Install TerraSync Software Getting Started Guide 31 2 Software Installation and Activation The Installation screen appears 6 TerraSync Trimble TerraSynce software Version 4 10 Go Back Main Menu Install Install on Windows Mobile 5 0 6 for Pocket PC Install on this PC Install fonts Install Microsoft NET Framework Version 2 0 x86 Install Adobe Reader 1995 2008 Trimble Navigation Limited All rights reserved This product is protected by US a
105. ation conventions 6 eee 12 About the TerraSync software 2 ee ee 12 TerraSync software editions 2 eee 13 Finding additional information 1 0 eea ee es 13 TerraSync Software Help 2 0 ce ee ee eee 14 TerraSync Software Quick Start Guide 2 ee eee 14 Release Notes gcs ewe oad ate a ke ele Slag Bis kw tk ot ania die Gib Eales 15 Technical assistance s pore ka ae tte ea ee te ala Bad ee ee ed ae Pe ai 15 Technical support tss ais hia dG wh ene ds Fedele a Koa ee oe ek RASS 15 Windows error reporting 1 ee ee ee 15 NOUPCOMMNMENUS 3 ies voce re cee to Aa See eke ee ea Eke Bee O Aa 15 2 Software Installation and Activation 20000 e eae 17 Systemi TEQUITEMENISy si eae ran era FO Oe ERODES REDE ee Pee ead awd 18 Field computer specifications 2 ee ee eee 18 Required software 1 1 eee a E E E R RD aE EE e BAGAS 18 Registering the TerraSync software 6 eee 19 Obtaining your installation code after registration 0004 24 Installing the TerraSync software 1 eee 26 Installing a translation of the TerraSync software 6 0 eee eee 26 Installing the TerraSync software onto a Windows Mobile powered device 26 Activating the TerraSync software 0 ee 37 Activating the software on a field computer powered by the Windows Mobile version 5 0 software or version 6 operatingsystem ee ee 37 Starting the TerraSync Software on a field co
106. attribute information needed for the traffic sign Once you finish entering the attributes tap OK to save the feature and return to the Collect Features screen TerraSync Software Getting Started Guide 101 5 Tutorial Collecting Data 7 Later in the tutorial you will navigate back to a sign that needs to be replaced and update its attributes You need to collect this traffic sign feature now Repeat Step 1 though Step to log another traffic sign feature When you reach Step 4 change the Condition field to Needs replacing Collecting a line feature with Log Later The next feature you need to record is a road This is a line feature To record a line feature you must travel along the line As you travel the TerraSync software records a GPS position at the configured logging interval which defaults to the value that was set when the feature was created in the data dictionary These positions are joined together to form a line By default the TerraSync software begins logging GPS positions as soon as you open a new feature For this feature you will use the Log Later option to delay logging of positions until you have entered the attributes for the feature and you have reached the start of the feature To record a line feature with the Log Later option 1 If the Collect Features screen is not already open a Tap the Section list button and then select Data b Tap the Subsection list button and then select Collect Features 2 Ta
107. been paused for more than five seconds before you segment the line the two line segments may not snap together Recording averaged vertices 184 A line or area feature consists of a number of positions joined in sequence from the first position logged to the last Each position represents a vertex see page 220 of the feature For more accurate recording of line and area features you can record several GPS positions at each vertex then average these GPS positions to calculate the vertex position Logging a line or area feature with averaged vertices is similar to logging a number of averaged point features and then joining these point features together in sequence To record an averaged vertex for a line or area feature see Collecting an area feature using averaged vertices page 108 Because an averaged vertex is similar to a point feature the same limitations that apply to a point feature apply when the Vertex form is open e You cannot segment a line feature while recording an averaged vertex e You can enter or edit the offset of the feature using the line area Offset form e While the Vertex form is open you must remain stationary as though you were recording a point feature The messages Vertex open and Remain stationary appear to remind you to stay still The number of positions recorded for this vertex also appears in the status bar A line or area feature can include both averaged vertices and positions logged n
108. by the Windows Mobile 2003 software some settings are stored in the main memory RAM even if the extension is installed to secondary internal storage To avoid data loss the installation program automatically backs up the main memory immediately after installing the TerraSync software If you installed the software from the CD Trimble recommends that you download the latest software updates and documentation from the Trimble website http www trimble com terrasync_ts asp TerraSync Software Getting Started Guide Software Installation and Activation 2 Step 7 Install fonts onto the Windows Mobile powered device When you install a translation of the TerraSync software on a Windows Mobile powered device you must also install a TerraSync language font if both of the following are true e You have installed the TerraSync software in one of the following languages Chinese Japanese Korean e The language version of the operating system does not match the language of the TerraSync software for example if you have installed the Japanese TerraSync software onto an English Windows Mobile powered device CAUTION Do not install the Japanese font onto a Windows Mobile powered device with the Japanese version of the operating system installed This can cause software errors on the device Tip If you see squares or unusual characters instead of characters from the appropriate language you need to install a font Chinese Jap
109. ceivers You can connect a field computer running version 4 10 of the TerraSync software to any of the following Field computers with integrated GPS receivers GeoExplorer series handhelds GeoXH GeoXM and GeoXT Juno SB and SC handhelds Juno ST handheld Trimble Nomad G series handhelds 800GL 800GLC 800GLE 800GX 800GXC and 800GXE Trimble Nomad handhelds 800L 800LC and 800LE purchased prior to January 2009 Trimble Recon GPS XB and XC editions Trimble Yuma rugged tablet computer GPS receivers GPS Pathfinder ProXRT receiver GPS Pathfinder ProXH receiver GPS Pathfinder ProXT receiver GPS Pathfinder Pro XRS receiver GPS Pathfinder XB receiver GPS Pathfinder XC receiver TerraSync Software Getting Started Guide 47 2 48 Software Installation and Activation e The following Trimble survey receivers 5800 receiver firmware version 2 23 or later R8 receiver firmware version 2 23 or later R8GNSS receiver firmware version 3 00 or later 5800 Model II receiver firmware version 2 23 or later Connecting to a GPS receiver You can connect the GPS receiver to a port on the field computer using one of the options described below Note To use GPS positions from the integrated GPS receiver when the TerraSync software is installed on a GeoExplorer series handheld configure the TerraSync software to connect to GPS on COM3 Port Connection
110. center of the earth to the east or west of the Greenwich meridian London England It comprises the east west component of the latitude longitude coordinate system which is used in GPS data collection Traditionally east is considered positive and west is considered negative Magnetic declination is the difference between magnetic north and true north Declination is expressed as an angle and differs between locations A bearing that is relative to magnetic north uses the north magnetic pole as its north reference MSL Mean Sea Level is a method of altitude reference Altitudes expressed in relation to MSL actually give a height above the geoid It is important to use the same geoid when comparing altitudes in MSL MTSAT Satellite Based Augmentation System MSAS is a satellite based augmentation system SBAS that provides a free to air differential correction service for GPS MSAS is the Japanese equivalent of WAAS which is available in the United States See Mean Sea Level See MSAS Multipath is interference that occurs when GPS signals arrive at the receiver having traveled different paths For example this may happen if some signals are reflected off a building before reaching the receiver If a signal takes a longer path it will show a larger distance to the satellite and therefore decrease position accuracy North American Datum of 1927 A horizontal datum employing the Clarke 1866 ellipsoid Height values of this era ar
111. ception and lets you see the tree clearly to assess its condition Specify an offset to the tree of 10 m South This is an example of an offset point feature Entering an accurate offset ensures that the feature is positioned correctly in the GIS north bearing line wW feature reference position Note The example above is a simple distance bearing offset For point features you can also record complex offsets which use measurements from two or more reference positions to calculate the feature position See also Complex offsets page 178 To view or enter the offset for the feature being collected or updated tap Options in the attribute entry form and then select Offset You can also use offsets for line and area features For example when collecting a line feature such as a fence it may be easier to drive along the road beside the fence and record the positions of the fence as an offset When collecting an area feature such as a lake you could walk some distance from the lake edge and record its perimeter using an offset TerraSync Software Getting Started Guide Advanced Datalogging Options A i 4 Line offset distance I N m Path traveled around lake l Area offset distance N 1 a i Note A feature point line or area can have only one offset associated with it To collect a line or area feature using offsets the same offset value must apply to the whole feature
112. certain tasks when you arrive at the collection site See e Starting the TerraSync software page 94 e Connecting to a GPS receiver page 95 e Checking the GPS status page 95 e Configuring the required logging accuracy page 97 e Configuring the antenna height page 98 e Configuring GPS quality settings page 99 D Starting the TerraSync software Tap 4 and then select Programs TerraSync By default the TerraSync software shows the Skyplot screen which shows the status of the connected GPS receiver The TerraSync software is arranged in the following five sections e Map e Data e Navigation e Status e Setup One of these sections is always active and visible The Section list button in the top left corner of the TerraSync software screen shows the section that is currently active To switch to a different section tap the Section list button and then select the section you want from the drop down list TerraSync Software Getting Started Guide Tutorial Collecting Data 5 If the current section has subsections the Subsection list button appears below the Section list button Use the Subsection list button to switch to a different subsection of the current section D Connecting to a GPS receiver e Ifthe field computer running the TerraSync software has an integrated GPS receiver the software automatically connects to the GPS receiver when you start the software e Ifyou are using a separate GPS receiver a Use ei
113. ch Click the Select button next to the Folder Search text box The Folder Search dialog appears Click Browse to navigate to the folder where the base files are stored Click OK The dialog closes and you are returned to the Base Data page of the wizard The base provider or the path of the folder you selected is displayed in the text box below the Base Data option you selected In the Reference Position group select Use reference position from base files Select the Confirm base data and position before processing option to make sure that the selected base files provide coverage for the rover files and that the reference position is correct TerraSync Software Getting Started Guide 123 5 Tutorial Collecting Data 12 Click Next The Output Page of the wizard appears Differential Correction Wizard r Output Folder Use the project folder C Use the same folder as the input file r Output Filename Create a unique filename based on the input filename Use original Filename overwriting any existing cor File This screen enables you to specify the output folder and output filename Use the default settings shown above 13 Click Start to differentially correct the selected files The Progress screen details the results of the differential correction If you selected the Confirm base data and position before processing option the Confirm button becomes available once the base files ar
114. ch e D S tee Bre gy Bookmarks gt Q signin 3 ma Ve BD Trimble Navigation Central Authentication Service M D page G Tos Trimble Central Authentication Service Enter your e mail address and password For security reasons please Log Out and Exit your web browser when you are done accessing services that require authentication E mail Password Create an account Eorgot password ee Click here to send us an email Version 1 7 copyright 2007 2009 Trimble Navigation All rights reserved Powered by JA SIG Central Authentication Service Copyright 2005 2009 JA SIG All rights reserved Local intranet If you already have an account skip this step and go to step 4 to log in To create your My Trimble account click Create an account Enter your contact details and then click Save Your account is created and you are returned to the My Trimble account login page Enter your email address and password and then click Login TerraSync Software Getting Started Guide Software Installation and Activation 2 The My Trimble page for your account appears It will look similar to the one shown below Home Windows Internet Explorer GS gt E http support trimble com CPRS Home aspx E 2 x cook File Edit view Favorites Tools Help We dt tiome gt D mh Eee Tos Trimble GIS s Profile My Trimble My Information GIS Jane GIS Company
115. collecting 4 Enter a value in each field as necessary Alternatively use data from a laser rangefinder See also Using a laser rangefinder to record offsets page 182 5 Log GPS positions for the feature 6 When the offset form is complete tap OK The attribute entry form reappears 7 When you have recorded attributes for the feature and logged sufficient GPS positions tap OK to store the feature The Collect Features screen appears Note You can also record complex offsets for point features see below Complex offsets When you record a complex offset you do not record any position information for the feature Instead you record GPS positions for two or three reference positions and measure the distance or direction from each reference position to the feature The TerraSync software uses coordinate geometry COGO to calculate the location of the feature in much the same way as a GPS receiver uses the distances to GPS satellites at known locations to calculate GPS positions In the TerraSync software record a complex offset using either two or three reference positions and specify either the distance to the feature or the bearing direction You can record the following types of complex offset e Distance distance offset see page 180 e Triple distance offset see page 180 e Bearing bearing offset see page 181 e Triple bearing offset see page 181 To increase accuracy record each reference position as if i
116. corrections are available the server may switch to raw mode In raw mode the server simply relays the corrections from the single physical base station that is closest to the roving receiver Unlike other real time correction sources using corrections from a VRS network requires two way communication between the server and the roving receiver The roving receiver must send its position to the server so that the server can calculate corrections for that position and select the closest base station if necessary Because the VRS network generates a unique virtual reference station for each roving receiver the server must send separate corrections to each roving receiver TerraSync Software Getting Started Guide 163 6 164 High Accuracy Data Collection Some VRS servers only provide carrier corrections for higher accuracy applications whereas others provide both DGPS code corrections and carrier corrections The accuracy you can achieve depends on the receiver used and the corrections from the VRS network You can use real time carrier corrections from a VRS network to achieve subfoot lt 30 cm and decimeter 10 cm accuracy with e GPS Pathfinder ProXRT receiver e GeoExplorer 2008 series GeoXH handheld You can use real time DGPS corrections from a VRS network with e GeoExplorer series handhelds GeoXH handhelds GeoXT handhelds GeoXM handhelds e GPS Pathfinder Pro series receivers GPS Pathfinder ProXT receiver
117. ction Table 6 1 Typical accuracies achieved after carrier phase data collection Time since acquiring lock Accuracy 10 minutes 20 cm 5ppm 20 minutes 10 cm 5ppm 45 minutes 1 cm 5ppm Required infrastructure for carrier phase data For carrier phase postprocessing a carefully surveyed base station is essential This must be within 80 km at all times and within 10 km if you are aiming for accuracy at the 1 2 cm level The base station must log dual frequency L1 L2 GPS data at a frequency no lower than 1 30 Hz once every 30 seconds Collecting sufficient high accuracy data When you open a new data file the TerraSync software starts to log carrier data in the background This allows the carrier block to start as soon as you open the file not just when you begin to log a feature As soon as four or more satellites are available a counter starts When enough time has elapsed for the GPS positions to obtain the accuracy you require see Table 6 1 page 158 all of the carrier phase data recorded during that period can be used during postprocessing Note When you open an existing file with carrier features the TerraSync software does not automatically log background carrier data Carrier logging only begins when you start logging positions to the file These may be not in feature positions position records for a new feature or updated positions for an existing feature TerraSync Software Getting Started Guide High
118. cture 56 sound 75 Standard edition 13 starting 56 text fields 69 three dimensional GPS position 96 time fields 70 TomTom Navigation software 81 TomTom Navigator 6 185 tooltips in status bar 74 transient messages 74 tracking defined 220 transferring files coordinate system export file 194 coordinate system files 195 transferring files from the field computer 118 to the field computer 133 transient messages 74 translations installing on PC 26 Trimble Data Transfer utility 18 Trimble Nomad handheld 47 99 Trimble numeric keyboard 55 Trimble Recon GPS XB edition 47 99 Trimble Recon GPS XC edition 47 99 TRIMMARK radio broadcasting corrections with 199 TRIMTALK radio broadcasting corrections with 199 triple bearing offsets overview 181 triple distance offsets overview 180 troubleshooting field computer problems 203 GPS problems 204 position accuracy 209 real time corrections 205 true north definition 220 turn by turn 81 128 turn by turn navigation 185 tutorial data collection 94 107 data update 135 preparing for data update 128 processing the data 118 U unattended base station 200 underlined letters in menus 66 uninterpreted sensor data 182 Update Features screen update status 142 update status filtering by tutorial 139 marking feature as updated tutorial 144 updating existing data 137 upgrade software 23 31 36 44 UTC definition 220 utilities Coordinate System Manager 193 Index
119. d Guide this document the following documentation is available e TerraSync Software Help e TerraSync Software Quick Start Guide e TerraSync Software Release Notes TerraSync Software Getting Started Guide 13 1 Introduction TerraSync Software Help You can access the TerraSync Software Help on your field computer This screen by screen reference explains all of terrasync Help the controls in each screen of the software Keyboard shortcuts The Help is context sensitive If you access the Help while the TerraSync software is running it opens at the topic that corresponds to the current TerraSync screen To access the TerraSync software context sensitive help lt iieiaei from e Map section Data section Navigation section Status section e Setup section e Legal Notices a Windows Mobile powered device tap EA and then select Help Contents Search Q gt If you tap H and then select Help on the device when the TerraSync software is not running the main Help Contents topic appears Tap Contents select Help for Added Programs and then select TerraSync Help to open the Contents topic of the TerraSync Software Help an office computer press F1 Alternatively hold down the Alt key on the keyboard and then press H TerraSync Software Quick Start Guide The TerraSync Software Quick Start Guide provides an overview of collecting GPS data including Starting the TerraSync soft
120. d to the Connections screen You have now configured the dialup networking connection Step 3 Connecting to the Internet using the dialup network l On the field computer go to the Connections screen if it is not already open tap EA Settings Connections Connections Below My ISP tap Manage existing connections Tap and hold the connection you want to use and then select Connect Unless the phone provider confirmed that you must enter user name password and domain settings to access the Internet tap OK on the left softkey without entering any information in this screen Otherwise enter the required information and then tap OK on the left softkey Ifthe phone prompts you for confirmation to connect to the Internet accept the connection The phone dials the configured GPRS access number and then connects to the Internet A Connectivity notification appears on the field computer as the connection is being made After the connection is made you are returned to the My ISP screen To confirm that the field computer is connected to the phone or to check the status of the connection at any time tap the Connectivity icon fi in the title bar The notification shows the name of the current connection and the time elapsed since the connection was made To hide the notification tap Hide Note If you have an active wireless LAN connection the connectivity icon appears as instead 6 Tap OK in the top right corner of
121. dd and then select Data File from the drop down list The Open dialog appears TerraSync Software Getting Started Guide 133 5 Tutorial Collecting Data 6 From the list of files select Starfish imp and then click Open The Open dialog closes and the Starfish data file appears in the Files to Send list n Device 9 GIS Datalogger on Windows Mobile o ito Devices 3 25 Connected to GIS Datalogger on Receive Send Windows Mobile Files to Send Add v Starfish 11KB Data File C Users JDoe Documents GPS Projects T erraSync ear heme Remove All Transfer All Retain File List for this Data Transfer Session Settings Help Close Click Transfer All The data file is transferred to the field computer and a message shows summary information about the transfer Click Close for the message and then click Close again to exit the Data Transfer utility To close the GPS Pathfinder Office software select File Exit in the main GPS Pathfinder Office window 134 TerraSync Software Getting Started Guide Tutorial Collecting Data 5 fj Exercise 6 Data update Note You cannot update imported data files using the TerraSync Standard edition software This part of the tutorial uses the data file that you have just transferred to the field computer You will use real time differential GPS in this section You are ready to go to Starfish Bay and update features
122. de 85 4 Software Structure Navigation section Navigate Options Goto Next Unvisited Waypoint Navigation Options Waypoints Waypoint New New Waypoint File List File Form Open Waypoint Options Set Nav Start List Set Nav Target Clear Nav Targets Delete Undelete Edit New Close File New Waypoint Create GPS Form From Map Point Selected Point Feature Selected Vertex Start Middle End Selected Waypoint Edit Waypoint Form 86 _ TerraSync Software Getting Started Guide Software Structure 4 Status section Skyplot Satellite Info Receiver Real time Summary External Integrated Beacon Integrated OmniSTAR Integrated SBAS Integrated RTK Radio Plan Options Show Orbits Off Trails Trajectories Hours 12 6 4 3 2 1 Report Play Pause Resume Set Time GPS Settings Sensor Sensor 1 Sensor 2 Comms UTC Time About System Report TerraSync Software Getting Started Guide 87 4 88 Software Structure Setup section Options Connect to GPS Disconnect from GPS Reset GPS receiver Activate Integrated OmniSTAR Connect to External Source Disconnect from External Source Ext Source GPS Reload Change Lock Logging Settings GPS Settings Real time settings Coordinate System Units External Sensors TerraSync Software Getting Started Guide CHAPTER Tutorial Collecting Data In this chapter This tutorial provides step by step instructi
123. de Processing option is selected Note The H Star processing options are available only if the GPS receiver used to collect the data file has H Star technology In this example the tutorial data files were collected with a GPS receiver that does not have H Star technology 6 Click Next The screen that appears specifies the correction settings that will be applied Differential Correction Wizard m Correct Settings Output corrected positions only Smart automatic rover filtering Re correct real time positions Change Cancel Help TerraSync Software Getting Started Guide 121 5 Tutorial Collecting Data 7 To change the correction settings click Change You can change Output and Base settings in the Correction Settings dialog Correction Settings Settings Output Positions Corrected and Uncorrected GPS Filtering Use smart automatic filtering recommended C Use data collection filter settings Use new filter settings Satellite Filtering Minimum Elevation Minimum SNR dBHz r Position Filtering MaximumPDOP 60 Maximum HDOP Eny z IV Re corect real time positions 8 Click OK to use the default settings 9 Click Next The Base Data screen appears ifferential Correction Wizard Base Data Base Provider Search Land Information NZ Taylor Lake Select Folder Search C Documents and Se
124. ded you retain no copies you transfer all of the Software including all component parts the media and printed materials any upgrades and this Agreement and the recipient agrees to the terms of this Agreement If the Software portion is an upgrade any transfer must include all prior versions of the Software 7 You may not use the Software for performance benchmark or comparison testing or analysis or disclose to any third party or release any results thereof all of which information shall be considered Trimble confidential information without Trimble s prior written consent 8 You agree to comply with all applicable laws and regulations of the United States and of other jurisdictions national state and local to the extent that they may govern your use of the Software Without limiting the foregoing you shall not directly or indirectly export re export import transfer or divert the Software in whole or in part i without all necessary authorizations required by law or ii to any prohibited destination or to any prohibited person entity or end user as specified by U S export control laws 9 To the extent that your use of the Software is limited to a specific number of installations and or seat licenses under the above license grant you agree to cooperate with Trimble to track the number of computers server computers and other devices with access to the Software at your site s or under your control to ensure compliance
125. dicates whether the estimated accuracy shown is for the horizontal or the vertical accuracy of the current GPS position Note The value shown depends on several factors including satellite geometry and the type of GPS receiver that is connected The estimated accuracy value flashes if the required accuracy set in the Accuracy Settings form is not met An arrow with no estimated accuracy value indicates that the software is unable to calculate the estimated accuracy Tap the icon for more information Shows that the TerraSync software is logging a feature with code accuracy The number at the bottom of the icon indicates the number of positions logged The number above the icon indicates the predicted postprocessed accuracy in the configured distance unit The width of the pen indicates code or carrier logging Logging static icon Shows that the TerraSync software is logging a point feature or vertex in static mode which is available only when the TerraSync software is receiving RTK corrections In static mode only the GPS position with the best precision estimate is logged All other positions are discarded The number to the right of the icon indicates whether a position has been logged If the required precision has not been achieved the number is 0 and no position is logged If a position with the required precision has been logged the number is 1 If a position with a better precision is received it replaces the previously logg
126. e recommends that you spend some time reading this guide to learn about the special features of this product If you are not familiar with GPS go to www trimble com gps for an interactive look at Trimble and GPS This publication assumes that you know how to use the Microsoft Windows operating system that you are using TerraSync Software Getting Started Guide 11 12 Introduction Documentation conventions The documentation shows the TerraSync software as it appears on a portrait orientation handheld with a 480 x 640 pixel screen On a larger screen or in landscape orientation some software items are displayed differently However there is no functional difference between the displays ma lerraSync PDOP Too few satellites a 7 Productivity Precision Too few satellites Productivity Precision Imn Landscape orientation 640 x 480 Portrait orientation 480 x 640 About the TerraSync software The TerraSync software collects and updates geographical data GIS and spatial data on a field computer A field computer is a handheld device for example a device powered by the Microsoft Windows Mobile operating system or a computer for example a laptop or Tablet PC running the TerraSync software You can connect a GPS receiver to a field computer that has the TerraSync software installed and use the software to
127. e Getting Started Guide High Accuracy Data Collection 6 When logging data for subsequent H Star processing configure the Estimated Accuracy icon to show a prediction of the accuracy that will be achieved after postprocessing The value of the predicted accuracy is inversely related to the length of time that you have continuously collected H Star data The longer the duration of carrier lock the better the accuracy which is indicated by a decreasing estimate When the predicted accuracy value shown reaches the accuracy you require for the feature you can stop logging The predicted accuracy applies to all positions logged since you acquired carrier lock on the required number of satellites The accuracy estimate has a 68 confidence level which means that 68 of the time the position will be within the estimated value shown when the position was collected providing that the data is processed against base stations that meet H Star technology requirements see page 154 Note If you lose carrier lock while collecting a feature the accuracy estimate increases and you must reacquire satellites and remain at the feature until the estimated accuracy value decreases to the required accuracy When collecting data for postprocessing you do not have to remain at the same feature until the required predicted accuracy value is reached If you are collecting a series of features and you have a clear view of the sky and so are unlikely to lose carrie
128. e altitudes relative to a different reference level or relative to a more accurate perhaps local mean sea level model you will need to process the heights in GPS Pathfinder Office before exporting them to the GIS The TerraSync software lets you specify a datum transformation and a map projection so that you can see your GPS position and the position of features you may have recorded in the local coordinate system This makes it easy for you to check your position or to navigate using a map produced by your GIS It also lets you specify whether heights will be shown relative to the local ellipsoid or relative to mean sea level For your convenience the TerraSync software hides the complexities of datum transformations and map projections behind the common names for the coordinate systems with which you may be familiar Each named coordinate system has an associated datum which encapsulates an ellipsoid and a number of zones each of which is a named instance of a particular map projection Coordinate systems available in the TerraSync software 192 The TerraSync software is supplied with a large number of coordinate systems and datums including most National Coordinate Systems You can also create your own coordinate systems and sites using the Coordinate System Manager utility in the GPS Pathfinder Office software You can easily load these coordinate systems into the TerraSync software using the Trimble Data Transfer utility T
129. e calculate your position A set of transformations that allow GPS positions in the WGS 84 ellipsoid to be transformed to projection coordinates with elevations above the geoid Essentially a coordinate system consists of a datum transformation a geoid model allocation and a projection definition The amount and direction by which your current heading differs from the cross track line The shortest direct path from the navigation start to the navigation target A data dictionary is a description of the objects to be collected for a particular project or job It is used in the field to control the collection of the spatial and attribute information about these objects The elements of a data dictionary could include point line and area features A datum is a mathematical model of the earth s surface World geodetic datums are typically defined by the size and shape of an ellipsoid and the relationship between the center of the ellipsoid and the center of the earth Because the earth is not a perfect ellipsoid any single datum will provide a better model in some locations than others Therefore various datums have been established to suit particular regions For example maps in Europe are often based on the European datum of 1950 ED 50 Maps in the United States are often based on the North American datum of 1927 NAD 27 or 1983 NAD 83 All GPS coordinates are based on the WGS 84 datum surface For more information see Model
130. e coordinate system database files and the related support files use the Data Transfer utility to transfer the coordinate system export file to the TerraSync software see Transferring coordinate systems page 193 For more information on using the Coordinate System Manager utility refer to the GPS Pathfinder Office Online Help Transferring coordinate systems There are two ways to transfer coordinate systems or sites to the TerraSync software e You can transfer a single coordinate system or site which you select at the time of transfer see page 195 e You can use the Coordinate System Manager utility to create a coordinate system export file that contains a number of coordinate systems zones datums and sites and then transfer this file to the TerraSync software see below TerraSync Software Getting Started Guide 193 B Coordinate Systems A The TerraSync software stores all its coordinate systems in one file When you load a new coordinate system into the TerraSync software the new file replaces any existing coordinate system or systems in the software If you transfer a single coordinate system or site all existing systems in the software are lost If you transfer a coordinate system export file make sure that you include any coordinate systems that you want to keep plus any new systems that you want to transfer to the TerraSync software CAUTION To prevent the loss of coordinate system information in the TerraSync soft
131. e downloaded or located 14 Click Confirm to proceed with processing 15 When processing is complete click Close to close the Differential Correction wizard For more information about differentially correcting data refer to the GPS Pathfinder Office Software Help 124 TerraSync Software Getting Started Guide Tutorial Collecting Data 5 Viewing data When the data is transferred and differentially corrected you can display edit and plot it using the GPS Pathfinder Office software The best way to view field data and to verify its integrity is to use the Map window in the GPS Pathfinder Office software Use the Map window to make graphical queries and measurements on the collected data You can specify the colors symbols and line styles for each feature To view the data 1 Inthe GPS Pathfinder Office software select File Open Select the Starfish cor file from the current project folder GPS Projects TerraSync Tutorial Starfish cor is the differentially corrected version of the file Starfish ssf which you transferred from the field computer 2 If the Map window is not visible select View Map Map 1 2 736 lt 0 361 km gt babae Ooa N Traffic Sign feature Park feature Road feature The Map window displays the selected file Note Your Map window may appear different from the one shown 3 To display the attributes of any feature on the map double click the feature
132. e expressed in NGVD National Geodetic Vertical Datum of 1929 216 TerraSync Software Getting Started Guide NAD 83 NMEA NTRIP office computer parity partnership PC PDOP Glossary North American Datum of 1983 A horizontal datum employing the GRS 80 ellipsoid The original realization of NAD 83 was almost identical to WGS 84 The current realization NAD 83 CORS96 differs from WGS 84 by up to a meter Initial letters of National Marine Electronics Association NMEA 0183 defines the standard for interfacing marine electronic navigational devices This standard defines a number of strings referred to as NMEA sentences that contain navigational details such as positions Most Trimble GPS receivers can output positions as NMEA sentences Networked Transport of RTCM via Internet Protocol NTRIP enables the streaming of DGPS or RTK correction data via the Internet Data is usually received using a modem and or a cellphone An NTRIP server is an Internet server that manages authentication and password control for differential correction sources including base stations and VRS networks and relays corrections from the source that you select An NTRIP server can be accessed by a number of users at the same time An office computer is any computer running Trimble postprocessing software Usually the office computer is a desktop computer located in the office but if you are running your data collection software on a laptop
133. e receiver TerraSync Software Getting Started Guide 165 6 High Accuracy Data Collection Step 2 Connecting the field computer to the phone and configuring the connection to the dialup network 1 Make sure that the field computer and the phone are within five meters of each other and that the Bluetooth radio in each device is turned on On the field computer tap J Settings Connections Connections Below My ISP tap Add a new modem connection Enter the name for the connection For example enter the name of the phone or the VRS network that you will connect to Settings Make New Connection Enter a name for the connection From the Select a Modem drop down list select i RE Bluetooth and then tap Next on the right softkey Bluetooth z If the phone you want to connect to is listed go to Step 7 below not listed a Tap Add new device or New Partnership The field computer searches for other Bluetooth devices and displays them in the list Cancel Es Next b From the list of available devices select the phone you want to connect to and then tap Next on the right softkey c To pair with the phone enter a passcode of your choice that you will easily remember onto the field computer and then tap Next on the right softkey d When prompted by the phone enter the same password and then accept the connection e On the field computer in the Partnership Se
134. ead out and will result in more precise data Note The postprocessing engine in the GPS Pathfinder Office software version 4 20 produces a better result with a more productive setting Because you are using accuracy based logging the GPS quality settings are less critical This is because GPS quality is handled as part of the estimated accuracy calculation for each GPS position By default the GPS slider bar is at the middle setting When using accuracy based logging Trimble recommends that you move the GPS slider further to the left which allows the receiver to use more satellites to calculate the position However this results in less stringent GPS quality settings and so may ultimately reduce the precision of GPS positions For the tutorial you will configure the GPS slider bar to enable you to log more positions 1 Tap the Section list button and then select Setup 2 Tap GPS Settings The GPS Settings form appears 3 Drag the slider control to the left to lower the GPS slider bar two positions This allows more satellites into the solution Because there are few GPS Settings GPS Receiver Port z obstacles to block your view of the sky this may eee Productivity Precision provide better overall results If the slider bar is ples set too high the precision of the positions DOP Type PDOP collected is high but there may be places in the a A Starfish Bay area that cannot be mapped EN ae T
135. ear are those in the TerraSync data folder on the field computer 6 Gs 8 9 From the list select the Starfish file Make sure that the Destination column shows the correct path to the GPS Projects TerraSync Tutorial folder you created earlier and then click Open The Open dialog disappears and the Starfish file appears in the Files to Receive list BP Data Transfer tlees Device ais Datalogger on Windows Mobile Do Epo Devices 3 9 Connected to GIS Datalogger on Receive Send Windows Mobile Files to Receive File Size Data Type Destination TIR Starfish 140KB Data File C Users JDoe Documents GPS Projects T erraSy er Remove All Transfer All Settings Help Close Click Transfer All The data file is transferred to the office computer and a message shows summary information about the transfer appears Click Close for the message and then click Close again to exit the Data Transfer utility For more information refer to the GPS Pathfinder Office Software Help TerraSync Software Getting Started Guide 119 5 Tutorial Collecting Data 120 amp Differentially correcting data Depending on the base station you are using to postprocess your data you may have to wait up to 24 hours to proceed with this next step Usually though base stations provide the last hour s data at a few minutes past the hour The data collected by GPS receivers is subject to
136. eating a Projectors ma cerai Pee etek daded Ped eae dew and Casa we 92 The Seaview data dictionary 2 20 00 eee eee 93 Checking the equipment siirsin 44046 Reise 440 OF hs O we ee eA 93 Exercise 2 Data collection 2 aeaa ssd adie a aaa a a eia 94 MATA tasks soi anei ail o See be T A a A AEE E e E a eT bn ee 94 Collecting new data cecceedawe eee tina aua eee whoa dee E 100 Exercise 3 Advanced data collection 1 0 0 cee ee ee 107 Reopening a data file for continuation of data collection 4 107 Collecting an area feature using averaged vertices 1 0 0 0000 ee eae 108 Collecting a line feature with differing attributes line segmentation 109 Collecting a point feature while collecting a line feature nesting 111 Collecting an area feature while collecting a line feature C ntin aton pse Ti 4a AS BEE eae a A a oh a 113 Collecting a line feature using a centre offset simple offset 0 115 Collecting a point feature that you cannot get close to complex offset 116 Exercise 4 Processingthedata aaua 118 8 TerraSync Software Getting Started Guide Contents Transferring data to the office computer 0 0 0 eee ee eee ee 118 Differentially correcting data 2 ee ee 120 Viewing datas isch uci wane FE Ad ata he Se a Gee ee a a ek ee a 125 Exporting data to GIS ig biG eee eed A oe OR RGSS ee R eis 126 Exercise 5 Preparing for
137. ected by transient messages In the Map section tap any item to display its Position information in a tooltip When you use the Measure tool in the map measurement information appears in a tooltip in the top left corner of the map display refer to the TerraSync Software Help 74 TerraSync Software Getting Started Guide Sound User Interface and Data Entry 3 The TerraSync software uses sound to indicate special conditions or events Often these conditions are accompanied by a change in a status icon For example when the battery on the GPS receiver gets low the battery icon in the status bar see page 57 flashes and the Low GPS battery see page 76 sound is played Note The TerraSync software does not monitor the battery status of the GPS Pathfinder XB receiver and will not audibly warn when the battery for this receiver is low The events and conditions that can occur fall into three categories Category Description Success An operation has been successfully completed or a warning condition has been resolved By default a success event uses a sound with rising tones System A message containing a question or information about an error that has occurred has appeared Before you can continue working with the TerraSync software you must tap a button in the message to acknowledge the message Warning A condition exists that could cause loss of data or could prevent you from collecting data successfully By defau
138. ections 135 specifications for field devices 18 SSF file format definition 220 SSF files imp extension 132 converting from GIS data format 130 converting into GIS data format 126 Starfish Bay tutorial 91 starting TerraSync software 56 static GPS position defined 220 minimum number of satellites 151 static mode definition 220 static mode animated logging icon 59 status bar real time beacon icon 58 real time external beacon icon 58 status bar antenna icon 58 base logging icon 59 battery icon 58 connect icon 57 digitizing icon 59 external real time icon 58 external RTK icon 58 filter icon 58 icons 57 integrated RTK icon 58 logging icon 59 logging static icon 59 logging vertex icon 59 memory icon 59 230 TerraSync Software Getting Started Guide overview 57 pause icon 59 real time satellite icon 58 real time SBAS icon 58 satellite icon 57 tooltips 74 Status section 81 streaming GPS position defined 220 structure of Data section 86 of Map section 83 Subsection list button 65 subsections 82 support 15 supported receivers 47 synchronization definition 220 T target icon Close up screen 141 Map section 143 target setting 140 task switching Windows Mobile powered device 53 technical support 15 TerraSync software color 77 creating a project tutorial 92 data entry 69 display 57 exiting 56 Help 14 52 opening a project tutorial 93 overview 80 Professional edition 13 screens and controls 62 section stru
139. ectly These devices may be connected to the field computer by cable or using Bluetooth wireless technology For more information about establishing a Bluetooth wireless link refer to the manufacturer s instructions for the Bluetooth enabled device Unlike the Internet connection method a direct dial connection is configured established and terminated from within the TerraSync software Authentication If the call is authenticated using Caller ID you will need to inform the service provider of the cellphone number that you are using Otherwise you may need to configure the modem to use a terminal window after dialling Before you begin For a direct dial connection you need the following information from the service provider e The dial up telephone number of the VRS network e Your username and password if the service provider requires you to enter these details when you connect to the VRS network Configuring a direct dial connection to a VRS network To configure the TerraSync software to establish a direct dial connection to a VRS network 1 Install any software or drivers for the modem 2 Start the TerraSync software and then open the Setup section 3 Tap Real time Settings The Real time Settings form appears 4 From the Choice J field select External Source TerraSync Software Getting Started Guide High Accuracy Data Collection 6 5 Configure the external source
140. ed after postprocessing The value of the predicted accuracy is inversely related to the length of time that you have continuously collected carrier data The longer the duration of carrier lock the better the accuracy which is indicated by a decreasing estimate When the predicted accuracy value shown reaches the accuracy you require for the feature you can stop logging The predicted accuracy applies to all positions logged since you acquired carrier lock on the required number of satellites The accuracy estimate has a 68 confidence level which means that 68 of the time the position will be within the estimated value shown when the position was collected providing that the data is processed against base stations that meet carrier phase requirements see page 158 Note If you lose carrier lock while collecting a feature the accuracy estimate increases and you must reacquire satellites and remain at the feature until the estimated accuracy value decreases to the required accuracy TerraSync Software Getting Started Guide 159 6 160 High Accuracy Data Collection Real time kinematic workflow and required infrastructure This section explains how to obtain centimeter level accuracy using real time kinematic data collection If you are using a survey receiver you can use real time kinematic RTK data collection to achieve centimeter level accuracy in real time Note In RTK mode the TerraSync software uses only RTK correct
141. ed position Logging vertex icon Shows that the TerraSync software is logging GPS position information for an averaged vertex including point features The number to the right of the icon indicates the number of positions logged for this vertex or point feature Base logging Shows that the TerraSync software is logging positions to a base data file or icon that is generating correction messages ef Digitizing icon Shows that the TerraSync software is in Digitize mode and GPS logging is 3 paused so tapping the map will result in a digitized position being recorded for the open feature The number to the right of the icon indicates the number of digitized positions logged for this feature Pause icon When logging is paused the pause icon flashes Memory icon When storage space is low the memory icon appears If memory gets low while you are logging positions the memory icon flashes alternately with the logging icon If you are not logging the memory icon appears alone and flashes Note When no icon appears in this position memory space is sufficient and the TerraSync software is not logging position data TerraSync Software Getting Started Guide 59 3 60 User Interface and Data Entry Table 3 2 shows the status bar icons and the tooltips that describe them Table 3 2 Status bar Tooltips Icon Behavior Tooltip 8 Solid GPS is calculating positions
142. ed positions You cannot configure the software to use uncorrected GPS positions and RTkK corrected positions cannot be postprocessed Required infrastructure for RTK RTK requires one of the following e alocal 20km base station This can be another Survey receiver that is set up as an RTK base station For information about how to use the TerraSync software to set up a second survey receiver as an RTK base receiver See Appendix C Setting up a Base Station e access to a VRS network that generates RTK messages in which case the base stations can be up to 70km away To use RTK corrections the rover requires a communication link to the RTK source This can be the receiver s integrated RTK radio or an external data radio connected to the receiver Alternatively if you are using RTK corrections from a VRS network you can use a variety of methods to establish a direct dial or Internet connection between the field computer and the VRS network See Using corrections from a VRS network page 163 Configuring the TerraSync software for RTK data collection To configure the TerraSync software to use RTK corrections 1 Open the Setup section 2 Tap Real time Settings The Real time Settings form appears 3 From the Choice J field select the real time correction source Ifthe roving receiver has an internal radio select Integrated RTK Radio Ifthe roving receiver is connected to an external data radio or the RTK source is a VRS netw
143. eiver you use for the base station you can set up the base station to e Log base data to a file see below which can be used to postprocess rover data in Trimble postprocessing software e Generate real time corrections for broadcast to DGPS or RTK rovers see page 199 The base receiver must be a receiver that is supported by the TerraSync software It must be capable of carrier phase data collection Table C 2 on page 198 shows the GPS receivers that can be used and the base station operations that each receiver supports Table C 2 Types of GPS receiver that can be used as a base station GPS receiver Log to base file Output DGPS Output RTK corrections corrections GeoXH Yes No No GeoxXT Yes No No GPS Pathfinder ProXH Yes No No GPS Pathfinder Pro XRS Yes Yes No GPS Pathfinder ProXRT No No No GPS Pathfinder ProXT Yes No No 5700 No Yes Yes 5800 No Yes Yes R8 No Yes Yes By default if you enable real time output for a GPS Pathfinder receiver it still logs base data to file If you only want to output real time corrections from a supported GPS Pathfinder receiver or if you are using a survey receiver you can use the TerraSync software to set up the receiver as an unattended base station see page 200 Logging base data to a file 198 The following receivers can log base data to a file for use in Trimble postprocessing software e GPS Pathfinder ProXH receiver e GPS Pathfinder ProXT receiver e GPS Pat
144. elect lt 80 km unless you know that the base Ueo anars Leite MGMM Apply Accuracy based Logging To station you will be using to postprocess your GPS z field data is nearer In that case enter the estimated distance to the base station From the Use Accuracy based Logging field select Yes From Apply Accuracy based Logging To field select All Features From the Required Accuracy field select 5 m 2 o NA Tap OK to save the settings and return to the Logging Settings form TerraSync Software Getting Started Guide 97 5 98 Tutorial Collecting Data Configuring the antenna height You must define the antenna type you are using because each type has different mechanical and electrical properties that affect the signal If the antenna is mounted on a standard or calibrated pole measure to the bottom of the antenna If the antenna is mounted on a tripod measure to the notch Use the Antenna Settings dialog to define the height of the antenna above the ground L From the Logging Settings form tap the Setup button Ea beside the Antenna Height field The Antenna Settings form appears In the Height field enter the height of the antenna for example 1 meter In the Confirm field select Per File From the Type field drop down list select the antenna type you are using for example GeoXH Internal Once you select the antenna type the Part Number field is automatically filled in
145. ellite icon flashes when the geometry of the satellites their PDOP or HDOP is poor The number below the icon indicates how many satellites are being used to compute GPS positions The number flashes when not enough satellites are available You need at least four satellites to compute GPS positions Connect icon amp When the TerraSync software is trying to connect to a receiver the connect icon appears instead of the satellite icon If the TerraSync software cannot connect to the GPS receiver the connect icon flashes TerraSync Software Getting Started Guide 57 3 58 User Interface and Data Entry Table 3 1 Status bar Icons continued Icon Name Description Antenna icon If the TerraSync software connects to the receiver but cannot find a GPS antenna the antenna icon appears instead of the satellite icon This icon flashes to warn you that there is a problem If no icon appears in this position no GPS receiver is connected H Real time external icon Shows that the TerraSync software is receiving real time corrections from an external source such as a radio Integrated RTK radio icon Shows that the TerraSync software is receiving RTK corrections through the GPS receiver s integrated radio a ie External RTK icon Shows that the TerraSync software is receiving RTK corrections through an external radio y A Real time external beacon icon Sho
146. ens the Map Data and Status sections are displayed To change the size of a pane drag the resize bar between it and the next pane Each pane has a minimum size so if resizing would make a pane smaller than its minimum dimensions it is automatically hidden You can use this feature to create three pane two pane or single pane layouts The Section list button determines which section appears in the primary pane The primary pane is the left pane or the top pane if only two panes are visible TerraSync Software Getting Started Guide 81 4 82 Software Structure To change the section that is displayed in the primary pane tap the Section list button and select a section from the list If the section is already displayed in a secondary pane the two sections switch position To change the section that is displayed in a secondary pane tap the Section list button that appears in the top left corner of the pane Then select a section from the list To move a section to a different pane tap and hold the Section list button The icon for the section appears Drag the icon into the pane where you want the section to be displayed When you drop the icon the two sections switch position Section structure Some sections have a number of subsections Ifthe Subsection list button current section has subsections the Subsection list button is visible You can switch to a different subsection of the current section at any time To do this
147. ent the earth s surface on a flat rectangular map mathematical formulas are used to project the earth s surface onto maps These mathematical formulas are called geoids and ellipsoids Frameworks called datums and coordinate systems help to further define how the earth is projected onto a particular map Geoids and ellipsoids A geoid is an imaginary three dimensional surface representing mean sea level MSL if it was projected to extend through the continents While we might assume that mean sea level remains constant over the surface of the globe in fact it does not Rather mean sea level varies from place to place due to variations in local gravitational forces which are in turn caused by local variations in the size shape and density of geological features This means that unlike an ellipsoid or datum which has a symmetrical surface the geoid undulates perpendicular to the force of gravity wore Geoid Ellipsoid Figure B 4 A geoid Using a geoid we can describe a feature of the earth in terms of the earth s actual terrain as well as by measuring gravity For example if we say that Mount Everest is 8848 meters above mean sea level then the vertical location of the feature on the surface of the earth has been identified by measuring gravity and comparing to mean sea level gravity Unfortunately a geoid is an extremely complex surface and is not always suitable for modelling the surface of the earth H
148. erials 1 5 U S Government Licensee Restricted Rights Applies only to US Government Licensees If you are the United States Government or any agency or contractor thereof use duplication or disclosure of the Software is granted with Restricted Rights subject to the restrictions set forth in this Agreement and as provided in FAR 52 227 19 c 2 or subparagraph c 1 ii of the Rights in Technical Data and Computer Software clause at DFARS 252 227 7013 and or in similar or successor clauses in the FAR or the DOD or NASA FAR Supplement 2 TIME LIMITED SOFTWARE In the event that the Software provided to you is a time limited version such as Software provided to Trimble resellers and distributors for sales demonstration purposes under a demonstration license or to prospective end user customers for evaluation purposes under an evaluation license Time Limited Software then the terms of this Section 2 shall apply and supersede anything else to the contrary including without limitation the limited warranty under Section 3 2 1 Use and Limited Term Disabling Mechanism You may use Time Limited Software solely for the purpose for which it is provided to you by Trimble e g reseller distributor demonstration or end user evaluation and only for the limited period of time specified by Trimble If no such limited time period is specified then you may use the Time Limited Software for 14 days from the date of its initial inst
149. erraSync Software Getting Started Guide Coordinate Systems B Note The default geoid in the TerraSync software is the DMA 10x10 Global model This is different from the default used by the GPS Pathfinder Office software As a result MSL heights in the TerraSync software may differ from those displayed in the GPS Pathfinder Office software Using the Coordinate System Manager utility Use the Coordinate System Manager utility in the GPS Pathfinder Office software to create and edit custom coordinate systems and sites for use with the TerraSync software This data can be saved to a coordinate system export file which you can then transfer to the field device To use the Coordinate System Manager utility 1 On the office computer start the Coordinate System Manager utility from the GPS Pathfinder Office software 2 Use the tabs in the main window to select or edit coordinate systems zones and sites AN CAUTION When you transfer a new coordinate system file to the field device it replaces all coordinate systems already stored in the TerraSync software Make sure that the new file includes all the coordinate systems that you want to use in the TerraSync software 3 Export the coordinate system database file Select File Export The Export dialog appears 4 Select the Selected records only option in the Export dialog 5 Click OK The Save As dialog appears 6 Specify the filename and click Save When you have saved th
150. erraSync software to collect H Star data For real time H Star technology l 2 3 O wenn Tap the Section list button and then select Setup Tap Real time Settings The Real time Settings form appears From the Choice 1 field select External Source Tap the Setup button Ea beside the Choice J field to configure the correction source and then select the appropriate settings depending on the VRS server and the communication method used see Using corrections from a VRS network page 163 When you have finished configuring the external source tap OK From the Choice 2 field select Wait for Real time Tap OK to confirm the real time settings and return to the main Setup screen Tap Logging Settings The Logging Settings form appears Make sure that the Log H Star Data field is set to Auto To use accuracy based logging a Tap the Setup button 7 below the Accuracy Settings field The Accuracy Settings form appears lerraSync oS Setup b From the Accuracy Value for Display Logging Acemaey Settings _OK Cancel fields select In the Field and whether the Acea cy vaUe hor eciey POUgint Horizontal x TerraSync software should calculate the aoa j e r n the fie id estimated horizontal or vertical accuracy Use Accuracy based Logging Yes v c From the Use Accuracy based Logging field Apply Accuracy based Logging To select Yes All Features X Required Accur
151. errors including small satellite clock errors orbit errors atmospheric noise and multipath errors The vast majority of these errors can be removed from the data by differential correction which improves the accuracy of GPS positions to the specified accuracy of the receiver To differentially correct the data file 1 Start the GPS Pathfinder Office software and then open the TerraSync Tutorial project 2 Select Utilities Differential Correction to start the Differential Correction wizard The file you transferred from the field computer appears in the Selected Files field Differential Correction Wizard Select SSF files to correct STARFISH SSF Start Time 07 30 08 10 17 35 End Time 07 30 08 15 09 07 Folder C Documents and Settings dwalton My Documents Positions 136 Collected with H Star receiver No Next gt Cancel Help 3 Ifthe SSF file does not appear click to locate the file Starfish ssf and then click Open TerraSync Software Getting Started Guide Tutorial Collecting Data 5 4 Click Next The Processing Type screen appears Differential Correction Wizard Processing Type Automatic Carrier and Code Processing Code Processing Only C Carrier Processing Only H Star Processing Use multiple base providers Use a single base provider lt Back Cancel Help 5 Select a processing option By default the Automatic Carrier and Co
152. es together 175 Index recording between feature positions 174 reference position 123 registration software 19 33 46 release notes 15 release notice 4 repeating features 183 resuming logging tutorial 103 rover definition 219 roving mode definition 219 RTCM definition 219 RTK base station overview 199 setting up 198 using corrections from 160 RTK data collection configuring TerraSync 160 definition 219 overview 159 RTK external icon 58 RTK from VRS network tooltip 60 S satellite icon 95 tooltip 60 satellite differential service troubleshooting 205 satellite geometry icon 57 SBAS integrated receiver 12 135 SBAS receiver icon 58 tooltip 60 screen orientation 12 screens overview 62 Seaview Authority tutorial 91 Seaview data dictionary 93 secondary pane 81 Section list button 65 sections in multi pane view 81 structure 83 switching between 65 segmenting line features 109 183 Select Base Provider dialog 123 Select Server form 168 sending error report 15 setting up a base station 198 TerraSync Software Getting Started Guide 229 Index Setup section overview 81 shortcut keys 66 site definition 219 Skyplot screen checking GPS status 95 SNR definition 219 software activation field computer 37 offline 41 online 38 troubleshooting 42 with existing key 39 software structure 80 software upgrade 23 sorting lists 64 sound customizing 76 disabling 76 overview 75 sources of real time corr
153. est level of real time GPS accuracy Accuracy available in the field making applications such as precise asset relocation possible More expensive field equipment Inability to operate in tough GPS environments where satellite signals are interrupted for example in high multipath environments or under tree canopy Operational constraints such as limited distance from a base station precisely surveyed base station infrastructure and either radio or cellular data and equipment costs TerraSync Software Getting Started Guide High Accuracy Data Collection 6 Principles of carrier phase data collection This section outlines some of the underlying principles of carrier phase data collection that apply to all three different carrier phase techniques H Star technology carrier phase postprocessing and RTK Carrier lock To achieve the target accuracy carrier phase data collection depends on maintaining carrier lock Carrier lock is achieved when the receiver is continuously locked onto and tracking the carrier measurements on a minimum number of satellites The minimum number of satellites required to maintain carrier lock depends on whether you are logging static or dynamic GPS positions When logging you must maintain lock on at least five satellites Events that cause loss of carrier lock include anything that might interrupt the reception of the satellite signal such as interference from tree canopy or buildings Lock is
154. exiting To exit the TerraSync software 1 Tap EJ in the upper right corner of the screen 2 When prompted to confirm closing the file and exiting the software tap Yes TerraSync Software Getting Started Guide 117 5 Tutorial Collecting Data Exercise 4 Processing the data After the data collection session use the GPS Pathfinder Office software to process the data collected and transfer it to the GIS 118 This part of the tutorial shows you how to transfer and view the data The tasks are Transferring data to the office computer see page 118 Differentially correcting data see page 120 Viewing data see page 125 Exporting data to a GIS see page 126 amp Transferring data to the office computer You must transfer the data you collected in the field from the field computer to the office computer L Switch on the field computer and the office computer and connect the two computers If the field computer is a laptop or Tablet PC for example make sure that there is a network connection between it and the office computer If the TerraSync and GPS Pathfinder Office software are installed on the same computer for example a laptop PC you must still transfer files between the TerraSync software data folder and the GPS Pathfinder Office project folder If the field computer is a Windows Mobile powered device connect the device to the computer for example using a USB cable or Bluetooth wireless technology
155. f you press D when the Option list is open in the Setup section the TerraSync software disconnects from the GPS receiver However if you press D in the Options list of the File Manager subsection the TerraSync software deletes the selected file If the TerraSync software is installed on a desktop or laptop computer the screen is arranged in panes Local shortcuts work only for the primary pane the pane in the top left of the screen This table lists the global shortcuts in the TerraSync software Action Keyboard shortcut Open Map section Alt M Open Data section Alt D Open Navigation section Alt N Open Status section Alt S Open Setup section Alt E Open Skyplot screen Alt K Open New File subsection Alt T Open Collect Features subsection Alt T Open Update Features subsection Alt U Start pause or resume logging GPS Alt L Close current data file Alt C Exit TerraSync Alt Q This table lists the local shortcuts in the TerraSync software Action Section Keyboard shortcut Select a command on an open list All sections Underlined letter Open the Options list for the current All sections alt O screen Open the Layers list Map Alt A Zoom in Map Anz Zoom out Map Alt Y Zoom extents Map Alt X Move up Map Alt up arrow key Alt 8 Move down Map Alt down arrow key Alt 2 Move left Map Alt left arrow key Alt
156. from the receiver s integrated SBAS differential receiver Flashing Waiting for real time corrections Solid Applying RTK corrections from the receiver s integrated RTK radio Flashing Waiting for RTK corrections Solid GPS receiver battery is good 75 U Field computer battery is good 75 Solid GPS receiver battery is low 25 Field computer battery is low 25 0 Flashing GPS receiver battery is critical 10 Field computer battery is critical 10 TerraSync Software Getting Started Guide User Interface and Data Entry 3 Table 3 2 Status bar Tooltips continued Icon Behavior Tooltip Note The battery icons and tooltips in this table show both batteries at the same level of charge However each half of the battery icon can appear in green yellow or red independently of the color and level of the other half Solid Filter is applied 4 Animated pen and Positions are being logged fea number increments Flashing pen GPS is not available Animated circle Vertex point feature capture in progress g 4 decreases in size Solid Ready to digitize 3 T Flashing Position logging is paused Flashing Memory is full o Tip A tooltip also appears when you tap a graphical item in the Skyplot screen TerraSync Software Getting Started Guide 61 3 User Interface and Data Entry Interacting with the TerraSync software You can interact with the TerraSync software in a variety of way
157. ft Corporation in the United States and or other countries The Bluetooth word mark and logos are owned by the Bluetooth SIG Inc and any use of such marks by Trimble Navigation Limited is under license All other trademarks are the property of their respective owners This product is covered by the following patent 6 377 891 Release Notice This is the December 2009 release Revision A of the TerraSync Software Getting Started Guide It applies to version 4 10 of the TerraSync software End User License Agreement TerraSync Software IMPORTANT READ CAREFULLY THIS END USER LICENSE AGREEMENT AGREEMENT IS A LEGAL AGREEMENT BETWEEN YOU either an individual or a single entity AND TRIMBLE NAVIGATION LIMITED and its affiliates collectively Trimble and applies to the TerraSync software product version 4 10 Standard or Professional editions provided herewith including any accompanying written materials such as a user s guide or product manual as well as any online or electronic documentation collectively Software This Agreement will also apply to any Software error corrections updates and upgrades subsequently furnished by Trimble unless such are accompanied by different license terms and conditions which will govern their use BY CLICKING YES OR I ACCEPT IN THE ACCEPTANCE BOX OR BY INSTALLING COPYING OR OTHERWISE USING THE SOFTWARE YOU AGREE TO BE BOUND BY THE TERMS OF THIS AGREEMEN
158. ftware and the Trimble GPS Analyst extension for ESRI ArcGIS software works with the TerraSync software Use the postprocessing software to create data dictionaries transfer data import and export files and postprocess collected GPS data TerraSync software editions The TerraSync software is available in two editions Standard and Professional The TerraSync Professional edition software offers several additional useful features With the Professional edition you can e update imported data files including SSF files transferred from TerraSync Standard edition software using the Trimble Data Transfer utility data files created from Shapefiles data files received by email e display background images or data files in the Map section e use an external sensor including laser rangefinders when collecting data e use a survey receiver to collect RTK data If you have purchased the TerraSync Standard edition software and would like to use these additional functions you can upgrade your software to the TerraSync Professional edition software For upgrade pricing details contact your local Trimble reseller This manual describes the TerraSync Professional edition software If a feature or option it describes is not available in the TerraSync Standard edition software this is indicated with a note at the beginning of the relevant section Finding additional information In addition to the TerraSync Software Getting Starte
159. g Started Guide 217 Glossary Position Dilution of Precision postprocessing predicted postprocessed accuracy PRN projection pseudo random number raster PDOP Dilution of Precision DOP is a measure of the quality of GPS positions based on the geometry of the satellites used to compute the positions When satellites are widely spaced relative to each other the DOP value is lower and position accuracy is greater When satellites are close together in the sky the DOP is higher and GPS positions may contain a greater level of error PDOP is a DOP value that indicates the accuracy of three dimensional measurements Other DOP values include VDOP vertical DOP and HDOP Horizontal DOP The TerraSync software lets you specify either a maximum HDOP value or a maximum PDOP It uses this maximum value as an upper bound on DOP values You can configure the desired level of accuracy and make sure that the positions logged are of a certain quality When the DOP exceeds this maximum the TerraSync software stops computing GPS positions Using a maximum PDOP value is ideal for situations where both vertical and horizontal precision are important Postprocessing is the processing of satellite data after it has been collected in order to eliminate error This involves using PC software to compare data from the rover to data collected at the base station Because the base station is on a known location any errors can be determ
160. g streaming GPS positions Your application logs a new vertex for every GPS position received from the GPS receiver Synchronization is the process where ActiveSync technology compares information on a Windows Mobile powered device with the corresponding information on the desktop computer and then updates either computer with the latest information The data stored by the TerraSync software is not synchronized by ActiveSync technology Use the Trimble Data Transfer utility to transfer data to and from the TerraSync software For more information refer to the ActiveSync Help and the Data Transfer Utility Help The process of receiving and recognizing signals from a satellite A bearing that is relative to true north uses the north celestial pole as its north reference Universal Time Coordinated UTC is a time standard based closely on local solar meantime at the Greenwich meridian GMT GPS time is directly related to UTC Universal Transverse Mercator Map Projection A special case of the Transverse Mercator projection Abbreviated as UTM it consists of 60 north south zones each 6 degrees wide in longitude A vector graphic is a graphical image consisting of mathematical descriptions of lines points and areas When you transfer an SSF data file to the TerraSync software as a background file its attribute information is removed leaving only the vector information You can view the features in the map but you cannot select them view
161. ge TerraSync Help Select any blue underlined text to jump to the topic it e Keyboard shortcuts describes e Map section e Data section The contents page of the TerraSync Software Help lists all Navigation section the main topics To access this page select the Contents e Status section link at the bottom of any Help page Setup section e Data Dictionary Editor e Legal Notices Contents Search Q gt Using the Windows operating system You can install the TerraSync software on an office computer desktop laptop or Tablet PC instead of on a Windows Mobile powered device This manual describes the TerraSync software as it appears on a portrait orientation handheld powered by the Windows Mobile 6 1 operating system with a 480 x 640 pixel screen see Documentation conventions page 12 On an office computer some software items appear differently The main difference is that on a larger screen the TerraSync software display is arranged in panes so you can view up to three sections at the same time see Panes page 81 Except where specified any information in this manual that relates to the operation of the TerraSync software on a Windows Mobile powered device also applies to its operation on an office computer TerraSync Software Getting Started Guide User Interface and Data Entry 3 Using the Windows Mobile operating system This manual assumes that you are reasonably familiar with the Microsoft Wi
162. ge of the operating system running on the device or field computer System commands such as the OK and Cancel buttons are generated by the operating system so they appear in the language of the operating system on the field computer If you use the TerraSync software on a field computer that does not have the corresponding translation of the operating system installed system commands are not translated Also some characters may not be interpreted or displayed correctly For best results make sure that the languages used by the TerraSync software and the operating system match If they do not install any font that is supplied with the TerraSync software for that language For more information see Step 7 Install fonts onto the Windows Mobile powered device page 35 Note The fonts that the TerraSync software uses are included with translated Windows desktop operating systems so you do not need to install them to use the TerraSync software on an office computer The TerraSync software is available in several languages To install a translation of the TerraSync software go to the Downloads section on the TerraSync support page http www trimble com terrasync_ts asp Installing the TerraSync software onto a Windows Mobile powered device This section describes how to install the TerraSync software onto a supported Windows Mobile powered device The installation procedure comprises the following steps TerraSync Software Getting
163. ges installing on PC 26 laptop computer see PC large screen appearance on 81 laser rangefinder definition 215 using to record offsets 182 latitude converting 191 coordinate system 190 definition 216 Index Layers menu button 66 line features collecting 102 collecting point features as well 175 continuing 175 offsets 176 segmenting 109 183 list buttons 65 lists 64 local datum 216 local ellipsoid 216 local shortcuts 67 lock accuracy achieved 154 defined 216 effect on PPA 157 159 locking device screen 55 Log Later overview 174 using to record only averaged vertices 184 Log Now 174 logging base data to file 198 immediately 174 later 174 logging in static mode icon 59 logging positions icon 59 tooltip 61 logging vertex icon 59 logging pausing and resuming tutorial 103 longitude converting 191 coordinate system 190 definition 216 low power level 60 magnetic declination definition 216 magnetic north definition 216 map layers colors 77 map projection 188 191 Map screen navigating in 143 Map section 80 81 map server definition 221 Map Tools list button 65 Map window in GPS Pathfinder Office displaying attributes in 125 viewing datain 125 marking features as updated 144 TerraSync Software Getting Started Guide 227 Index mean sea level MSL as reference level 192 overview 188 Mean Sea Level definition 216 memory full icon 59 tooltip 61 menu buttons 66 menu fields 70 messages
164. grade from a previous version of the TerraSync to version 4 10 you can download the software from www rimble com terrasync_ts asp Click Downloads and then click v4 10 Software The Setup screen appears S TerraSync Trimble TerraSynce software Version 4 10 Main Menu Install Register Read documentation www trimble com 1995 2009 Trimble Navigation Limited All rights reserved This product is protacted by US and intsmational copyright trademark and patent laws as described in Status About Note If this screen does not appear select Autorun exe from the CD drive folder 3 Click Install 44 TerraSync Software Getting Started Guide Software Installation and Activation 2 The Installation screen appears 6 TerraSync Trimble TerraSynce software Version 4 10 Go Back Main Menu Install Install on Windows Mobile 5 0 6 for Pocket PC Install on this PC Install fonts Install Microsoft NET Framework Version 2 0 x86 Install Adobe Reader 1995 2008 Trimble Navigation Limited All rights reserved This product is protected by US and intemational copyright trademark and patent laws as described in Status About Select the Install on this PC option The Choose Setup Language dialog appears Choose Setup Language em Select the lanquage for this installation from the choices below English United States v Select the language that you require to run the inst
165. he Data Dictionary Ifthe GPS position for the feature is updated the GPS information in the EXIF record is also updated but the Original Time and Date the photo was taken is not changed unless the photo is also replaced Integration with CoPilot Live 7 Professional for Trimble TerraSync and TomTom Navigator 6 turn by turn navigation software When CoPilot Live 7 Professional for Trimble TerraSync or TomTom Navigator 6 navigation software is installed on the device and a navigation target is selected the TerraSync software automatically switches to using the navigation software to navigate to the selected target then switches back when you have arrived at the destination Features or waypoints can be selected as the navigation target If the turn by turn navigation software is not already running when the target is set in the TerraSync software the TerraSync software will also launch the navigation software A TerraSync tray icon in the Windows Mobile Today screen assists in switching between the TerraSync software and the CoPilot or TomTom navigation software if required Tip To make switching between applications even easier use the Windows Mobile Buttons application to program the keypad buttons as shortcuts to each application TerraSync Software Getting Started Guide 185 A Advanced Datalogging Options 186 TerraSync Software Getting Started Guide CHAPTER Coordinate Systems In this chapter Modelling the ear
166. he TerraSync software 6 You and your field crew have replaced the damaged sign so in the Condition field select Good 7 Tap OK to save the attribute changes and return to the Update Features screen For more information refer to the TerraSync Software Help X Tip In the Update Features screen the Updated column of the Choose Feature list shows the update status of each feature Any feature that has been transferred from the GPS Pathfinder Office software has an empty circle y in this column When a transferred feature is updated a check mark appears in the circle g 142 TerraSync Software Getting Started Guide Tutorial Collecting Data 5 Q Selecting a target in the Map section Finally you need to revisit the Road feature called Seagull Street You will use the Map section to navigate to the beginning of Seagull Street Note Your Map screen may appear different from the one shown To select a target using the Map section 1 Tap the Section list button and then select Map 2 Ifnecessary zoom in or out until all the features in the data file are visible 3 The Seagull Street feature is the only line feature on the map Tap any part of the line feature to select it A selected line feature has a wider line than an unselected line feature When you select a feature a tooltip shows the number name and position of the feature 4 Tap Options select Set Nav Target and then select 3Road Start from t
167. he corrected positions can be automatically transformed to WGS 84 before being saved to the SSF file In the Setup section for each real time correction source you use assign the appropriate Correction Datum value Some such as SBAS are assigned by default but if you use other sources such as a VRS network you need to find out which datum the system uses so that you can assign the correct value To send the WGS 84 positions that are stored in the SSF file to a GIS as North East coordinates the GPS latitudes and longitudes need to be processed in a number of ways The remainder of this section describes the steps that are required to perform this processing First the collected GPS positions must be transformed from latitudes longitudes and altitudes on the WGS 84 datum into latitudes longitudes and altitudes on the local datum This operation is called a datum transformation Once the coordinates are expressed as latitudes and longitudes on the local datum they must then be projected into North and East values on a flat grid using an operation called a map projection TerraSync Software Getting Started Guide 191 B Coordinate Systems Note Data files exported from the GPS Pathfinder Office software are stored using the currently configured export coordinate system If you change export coordinate systems the coordinates of the current data file are recalculated which may take some time SSF files are assumed to contain pos
168. he message The pop up message disappears TerraSync Software Getting Started Guide 73 3 User Interface and Data Entry Error messages are examples of pop up messages Warning and Error messages should be noted because they contain important information about the task you are trying to perform Tooltips A tooltip is a yellow message that contains information about an item on the screen or about the current system status TerraSync Data Position logging is Collect Options Log Tooltips appear e when you tap on an icon in the status bar e as transient messages in the status bar e when you tap on an item on the map e when you measure distances and areas on the map To close a tooltip tap it or tap anywhere else on the screen If you tap an icon in the status bar see page 57 a tooltip appears over it The tooltip contains information about the current state of the system function the icon represents For example if you tap the Filter icon see page 58 when a filter is in use a tooltip appears showing the message Filter is applied A transient message shows information that is only important for a few seconds such as notification that you have successfully recorded an offset with a laser rangefinder or that the feature has been stored A tooltip that contains a transient message appears over the status bar for three seconds or until you tap the tooltip Other functions in the software are not aff
169. he pullout menu The target icon appears at the start point of the selected road ett 000A Navigating to a target in the Map section Once you select a target from the map use the map to guide you to this target The GPS cursor w shows your current position and heading Note Your Map screen may appear different from the one shown To navigate to the target make sure Target that the heading arrow on the GPS cursor points toward the target as you move x GPS cursor et 3700680 0 You may need to zoom or pan in the map to ensure that both the target and the GPS cursor are visible When the target is not visible the bearing arrow f at the edge of the map shows its direction When the GPS cursor lies over the target icon you have successfully navigated to the target TerraSync Software Getting Started Guide 143 5 144 Tutorial Collecting Data Q Marking a feature as updated You have navigated to the road feature Now you can check its attributes and change its status to Updated To mark a feature as updated 1 Make sure that the Map section is in view If it is not tap the Section list button and then select Map The road you navigated to should be the selected feature 2 Double tap the road feature to open its attribute EEEE entry form Note If the attribute entry form appears briefly then disappears after
170. he type of Microsoft operating system running on your computer For more information refer to the GPS Pathfinder Office Software Help 5 Click OK to close this dialog and create the new project 6 Inthe Select Project dialog TerraSync Tutorial is selected in the Project Name field Click OK to open the new project the Seaview data dictionary A data dictionary contains a description of the features and attributes relevant to a particular project or job You use it in the field to control the collection of a feature and its attributes The signs roads and parks in Starfish Bay that you need to map are features The different types of information that you record for each type of feature are attributes For example the condition of a sign or the name of a park would be an attribute To ensure that the data you collect in the field is in the correct format for the Seaview Authority GIS you need to use a data dictionary that contains the same features and attributes as the Seaview Authority GIS The Seaview data dictionary has already been created for this purpose When you installed the TerraSync software on your field computer this file was automatically installed Checking the equipment Before going out into the field with the TerraSync software check that you have all the necessary GPS hardware batteries and cables Before you leave the office Trimble recommends that you e setup your entire GIS GPS data collection sy
171. held or to a removable storage device 8 When the installation is complete perform a soft reset of the device For information how to perform a soft reset refer to the documentation for the device 36 TerraSync Software Getting Started Guide Software Installation and Activation 2 Activating the TerraSync software Activating the software on a field computer powered by the Windows Mobile version 5 0 software or version 6 operating system The TerraSync software version 4 10 must be activated once it is installed on a field computer that is powered by the Windows Mobile 5 0 software or version 6 operating system To do this 1 Ifnot already started by the installation process start the Activation Wizard Click Start All Programs Trimble TerraSync 4 1 WM Trimble TerraSync Activator The Activation Wizard was installed on your office computer during the TerraSync software installation Note The Activation Wizard is a NET framework application If your office computer is running the Windows XP or Windows Vista operating system you must also have the latest Service Packs installed 2 Select your preferred language Choose Language Select the language for the Activation Wizard from the choices below English United States The Activation Wizard connects to the field computer through Microsoft ActiveSync technology or the Windows Mobile Device Center TerraSync Software Getting Started Gu
172. hfinder Pro XRS receiver e GeoExplorer GeoXH handheld e GeoExplorer GeoXT handheld TerraSync Software Getting Started Guide Setting up a Base Station C To log base data to a file open the New File screen and start a new base data file Then step through the Base Station Setup wizard For more information refer to the TerraSync Software Help Generating real time corrections The following receivers can output real time corrections e GPS Pathfinder Pro XRS receiver e All supported survey receivers To broadcast real time corrections configure the base receiver to generate real time correction messages Then either use the internal transmit radio in an R8 receiver or connect the base receiver to a data radio such as a TRIMTALK or TRIMMARK radio which broadcasts the correction messages Survey receivers can output DGPS corrections in the RTCM correction messages message format These corrections can be used by any rover that can use RTCM corrections from an external source such as a GPS Pathfinder receiver or a GeoExplorer series handheld In addition to DGPS corrections in RTCM format survey receivers can also output RTK corrections in RTCM CMR or CMR format RTK corrections can only be used by RTK capable rover systems such as a survey receiver connected to a field computer running version 2 40 or later of the TerraSync software The correction types and message format that you choose depend on the capabilities of the ro
173. hree reference positions A B and C to specify the position of the feature The feature lies at the point where the circles centered on A B and C intersect There can be only one point where the three circles intersect so you usually do not need to specify a direction A triple distance offset is similar to a distance distance offset but a third measurement provides some mathematical redundancy that can improve accuracy e from C to feature Distance from A to feature Distance frm B to feature Feature TerraSync Software Getting Started Guide Advanced Datalogging Options A Bearing bearing offset A bearing bearing offset uses the bearing from north from each of two reference points A and B to the feature to specify the position of the feature The feature lies at the point where the two bearing lines intersect North 4 Bearing line from A Bearing line from B l l l Bearing froma l Bearing from B Feature Triple bearing offset A triple bearing offset uses the bearing from north from each of three reference points A B and C to the feature to specify the position of the feature The feature lies at the point where the three bearing lines intersect A triple bearing offset is similar to a bearing bearing offset but a third measurement provides some mathematical redundancy that can improve accuracy North 4 l l Bearing from C l Bearing line from A
174. iate keyboard when you select a field that accepts data entry and hides the keyboard when you select a control that does not accept keyboard input Tip The keyboard button on the taskbar shows the icon of the currently selected on screen keyboard TerraSync Software Getting Started Guide User Interface and Data Entry 3 To change the selected keyboard 1 Tap the arrow on the right end of the on screen keyboard button A list of installed keyboards pops up The currently selected keyboard is indicated by a bullet or check mark 2 Tap the name of the keyboard required The pop up list closes automatically Trimble numeric keyboard When you install the TerraSync software on a device that uses on screen keyboards the Trimble numeric keyboard is also installed This keyboard contains numeric and symbol keys that are useful when you enter numeric data or time information This keyboard is available to other programs on the device as well as to the TerraSync software Note The Trimble numeric keyboard is available only on Windows Mobile powered devices that use on screen keyboards Device Lock utility The Device Lock utility is installed with the TerraSync software on a Windows Mobile powered device It lets you lock the device so that accidentally pressing the screen keys or hardware buttons has no effect Locking the device lets you safely clean the screen or exterior of the device transport it or to carry
175. ice select the lt 80km 7 distance to the base station from the Use Accuracy based Logging Yes 7 Postprocessing Base Distance field Apply Accuracy based Logging To E d From the Use Accuracy based Logging field select Yes e From the Apply Accuracy based Logging To field select the feature types that will use accuracy based logging f In the Required Accuracy field enter the accuracy you require g Tap OK to save the accuracy based logging settings and return to the Logging Settings form Note If your GPS receiver does not have H Star technology the Auto setting corresponds to No Select No if you have a GPS receiver that has H Star technology but you do not want to log H Star data 5 Tap OK to close the Logging Settings form and confirm the changes you have made Collecting sufficient high accuracy data During GPS data collection where the TerraSync software logs data using a receiver with H Star technology the software will show either the estimated accuracy being achieved for that position in real time or a prediction of the accuracy that is likely to be achieved once the H Star data is postprocessed When operating in real time H Star mode configure the Estimated Accuracy icon to show an estimate of the accuracy being achieved for that position in the field When the value shown in the Estimated Accuracy icon reaches the accuracy you require for the feature you can stop logging TerraSync Softwar
176. ice or the activation key is not on the device you installed the TerraSync software from See Activating the TerraSync software page 37 TerraSync Software Getting Started Guide 203 D Troubleshooting GPS This section lists problems when you use GPS or a GPS receiver Problem Possible cause Solution The message No GPS detected appears The cable connecting the field computer to the GPS receiver has not been connected has been connected incorrectly or is faulty Check that the cable is connected correctly If it appears to be correct and all other equipment appears to be correct the cable may require servicing The COM port on the field computer is faulty Check that the COM port is undamaged If it appears to be damaged the field computer may require servicing The GPS receiver s battery has not been connected correctly Check that the battery is correctly connected The GPS receiver s battery is dead Recharge the GPS receiver s battery Connect to an external power source The receiver has not acquired a satellite within three minutes of starting the TerraSync software The receiver is still looking for satellites The expected satellites are being obstructed Check the Satellite Information section see page 87 to see how many satellites are being tracked by the receiver The obstruction may be a building a tree or a large vehicle Identify the obst
177. ide 37 2 Software Installation and Activation 3 Select an activation method Activation Wizard Trimble Select an Activation Method wish to activate the Trimble TerraSync software over the Internet re already have a Trimble TerraSync software Activation Key for this device I donot have an Internet connection Select this method If See wish to activate the Trimble TerraSync Your office computer is connected to the Internet page 39 software over the Internet Trimble recommends this method already have a Trimble TerraSync software If your Trimble Reseller has provided you with an page 39 Activation Key for this device Activation Key or you have previously activated this Installation Code on the same field computer and kept a record of the Activation Key do not have an Internet connection You do not have an Internet connection page 41 Product information The Wizard will now extract information about the connected device that will help you identify it at a later stage Activation Wizard P a 3 SILL Enter Device Information You have connected a Trimble Mapping and GIS device Please review your device name change if necessary and click Next to proceed 38 TerraSync Software Getting Started Guide Device Name Trimble G eoExplorer Seried Device Serial Number 4830462025 Software Installation and Activation 2 You will be able to edit the Device
178. ined and removed from the rover data The predicted postprocessed accuracy is a prediction of the accuracy that will be achieved after postprocessing When logging H Star or carrier data the predicted postprocessed accuracy value applies to all the positions collected since you achieved lock on the required minimum number of satellites For all other receivers this value applies only to the current position The predicted postprocessed accuracy has a 68 confidence level which means that 68 of the time the postprocessed position will be within the predicted postprocessed accuracy value shown when the position was collected See pseudo random number A mapping of a set of coordinates from a datum to a plane or a set of mathematical rules for performing such a translation Projections are used to create flat maps that represent the surface of the earth or parts of it PRN The pseudo random number is the code of 0s and 1s transmitted by GPS satellites which appears to be random noise but is actually a complex pattern that can be exactly reproduced Each satellite has its own unique PRN code which together are used by the GPS receiver to calculate code phase positions A raster graphic is a graphical image consisting of rows and columns of dots The color of each dot is represented by the value of one or more data bits in the image file A bitmap bmp file is a type of raster image 218 TerraSync Software Getting Started G
179. ined list of values associated with it To change the selected value tap the drop down arrow at the right of the field and select an option from the list Condition Needs replacing EA Unselected field with drop down list available Field name Type Selected field with drop down list displayed List of values forthe selected field Scroll bar The current value in a drop down list is selected To choose a different value select the value from the list If a drop down list has more options than fit on one screen a scroll bar appears on the right Drag the scroll bar or tap the arrow buttons to scroll up and down the list Some menu fields can store either a value you enter or a value you select from a list For example in the Data form in the Setup section the Jnterval field can accept either an integer 1 through 999 or Off Enter a value manually using an on screen or physical keyboard or select a value from the drop down list Time Enter time values manually using an on screen or physical keyboard or select the current time from a drop down list If the field computer uses on screen keyboards the Trimble numeric keyboard pops up when you select a time field To enter the current time tap the arrow at the right of the field and select Now from the drop down list In the data dictionary you can specify that a time attribute is automatically set to the current time when the feature is created when
180. ing For more information refer to the documentation provided with the GPS receiver and the real time correction device TerraSync Software Getting Started Guide 49 2 Software Installation and Activation 50 TerraSync Software Getting Started Guide CHAPTER User Interface and Data Entry In this chapter This chapter contains detailed information about the TerraSync software user interface and data m Getting help entry methods Using the Windows operating system m Using the Windows Mobile operating system E Starting and exiting the TerraSync software m Section structure m The TerraSync software display Interacting with the TerraSync software TerraSync Software Getting Started Guide 51 3 52 User Interface and Data Entry Getting help The TerraSync Software Help describes the fields and commands for each screen To access the TerraSync software context sensitive help from e a Windows Mobile powered device tap EA and then select Help If you tap BG and then select Help on the device when the TerraSync software is not running the main Help Contents topic appears Tap Contents select Help for Added Programs and then select TerraSync Help to open the Contents topic of the TerraSync Software Help e an office computer press F1 Alternatively hold down the Att key on the keyboard and then press H The Help for the TerraSync software is displayed in HTML pages It works in the same way as a Web pa
181. ing amp GIS software A POPN is a sequence of 27 digits characters and hyphens that is printed on the case of the software installation CD The POPN will look similar to this example 001234 00300 00000 A537DB41 Local intranet TerraSync Software Getting Started Guide 21 2 Software Installation and Activation 5 Select the Add a Proof of Purchase Number POPN option and then click Next The Proof of Purchase Number POPN Details page appears Home Windows Internet Explorer 6 http support trimble com CPRS Home aspx Bile Edit View Favorites Tools Help we amp Ehme Trimble GIS s Profile Logout Add New Product Proof of Purchase Number POPN Details Please enter the POPN details as supplied Proof of Purchase Number POPN o0000 Your Reference Use the Reference field to add your own value of 25 characters or less to link to an external database Cancel lt Back Next gt Local intranet 6 Enter the Proof of Purchase Number POPN provided on the TerraSync software packaging The POPN is located on the product label inside the software folder below the software CD 7 Ifyou want to enter your own reference code for example a sales order number or an asset inventory number enter it in the Your Reference field 8 Click Next Note Ifa message warns that the POPN you entered has already been registered click Cancel to cancel the registration process
182. ions are joined together to form the perimeter of the area so there is no need to return to the exact start point When you logged the road feature you recorded the attributes before you started to log GPS positions For the park feature you will log GPS positions at the same time as you record the attributes To collect an area feature L ne N If the Collect Features screen is not already open a Tap the Section list button and then select Data b Tap the Subsection list button and then select Collect Features Tap Options and then select Log Now Move to where you want to record the first perimeter position From the Choose Feature list select Park Tap Create The attribute entry form for the Park feature opens and the TerraSync software starts to log positions You can pause logging at any time For example if you are driving around the perimeter of the park and you want to stop to examine a sign some distance from the park you can stop logging ane ne L positions for the park boundary You can also R pause logging if you want some time to enter attribute values Tne To pause logging tap Pause The TerraSync LJbIF software stops logging positions and a pause icon flashes in the status bar To continue collecting the park feature tap Resume to resume logging The pause icon disappears To view the map while collecting features tap the Section lis
183. ip When you are not using accuracy based logging or are not postprocessing using the postprocessing engine in the GPS Pathfinder Office software version 4 20 or later or the GPS Analyst extension for ESRI ArcGIS Desktop software version 2 20 or later use a high precision setting on the GPS slider bar whenever a project requires the highest level of precision ante awh ee Select COM3 for the internal GPS receiver 4 Tap OK to close the GPS Settings form TerraSync Software Getting Started Guide 99 5 100 Tutorial Collecting Data Collecting new data Your supervisor has sent you to Starfish Bay to map new road signs roads and park assets This part of the tutorial gives step by step instructions for the following tasks Creating a new data file see page 100 Collecting a point feature with Log Now see page 101 Collecting a line feature with Log Later see page 102 Collecting an area feature see page 103 Creating a waypoint see page 105 Ending the data collection session see page 106 Creating a new data file Before starting the data collection session you must create a new data file to store the new features and attributes you collect Use the Data section to do this To create a new file 1 2 Tap the Section list button and then select Data Tap the Subsection list button and then select New File The New File screen appears The TerraSync software automatically enter
184. irect dial connection that you have set up 1 Connect to the VRS network a Ifthe TerraSync software is not connected to the GPS receiver tap the GPS button to connect to the GPS receiver If you selected the Auto option in the Connection Control field the TerraSync software automatically initiates the connection If you selected the Auto option you must initiate the connection to the server To do this tap Options and then select Connect to External Source Ifnecessary enter your username and password in the terminal window that appears TerraSync Software Getting Started Guide 171 6 High Accuracy Data Collection 2 Proceed with data collection Use the Real time Summary screen in the Status section if you want to check the status of the VRS network 3 When you have finished using corrections from the VRS network a To manually disconnect from the VRS network in the Setup section of the TerraSync software tap Options and then select Disconnect from External Source b To ensure that the call is ended use the End Call command on the cellphone 172 TerraSync Software Getting Started Guide CHAPTER Advanced Datalogging Options In this chapter Log Now and Log Later Recording between feature positions m Continuing line and area features Offsets Using a laser rangefinder to record offsets Using an external sensor Repeating features Segmenting line features Recording averaged vertices
185. it To lock the device tap Device unlocked in the Today screen The Today screen shows Device locked and Unlock appears in the left corner of the menu bar Tip If Device unlocked does not appear in the Today screen you may need to add it to the items that appear in the Today screen To do this tap A Settings Personal Today Tap the tems tab and make sure that the check box next to Device Lock is selected Once the device is locked the screen hardware buttons including Record and Power buttons and keypad ifit has one do not respond until the device is unlocked Communication with external devices such as a GPS receiver or external sensors used by the TerraSync software is not interrupted by locking the device This means that you can keep using the TerraSync software when the device is locked For example you could lock the device so that you can safely transport it in your pocket between features but keep the TerraSync software connected to the GPS receiver so that you can collect a continuous block of carrier phase data To unlock the device tap Unlock in the left corner of the menu bar of the Today screen and then tap Unlock TerraSync Software Getting Started Guide 55 3 56 User Interface and Data Entry Starting and exiting the TerraSync software To start the TerraSync software do one of the following Py st Tap Programs TerraSync ones inchs e Tap Bj and then tap the TerraSync icon on the ie
186. ited warranty period which are provided AS IS and without warranty unless otherwise specified in writing by Trimble ADDITIONALLY TRIMBLE MAKES NO WARRANTIES EITHER EXPRESS OR IMPLIED REGARDING THE CUSTOMIZED APPLICATIONS OR USE OF THE SOFTWARE WITH ANY THIRD PARTY HARDWARE OR EQUIPMENT Because the Software is inherently complex and may not be completely free of nonconformities defects or errors you are advised to verify your work Trimble does not warrant that the Software will operate error free or uninterrupted will meet your needs or expectations or that all nonconformities can or will be corrected 3 2 Customer Remedies Trimble s and its suppliers entire liability and your sole remedy with respect to the Software shall be either at Trimble s option a repair or replacement of the Software or b return of the license fee paid for any Software that does not meet Trimble s limited warranty The foregoing limited warranty is void if failure of the Software has resulted from 1 accident misuse abuse or misapplication 2 alteration or modification of the Software without Trimble s authorization 3 interaction with software or hardware not supplied or supported by Trimble 4 your improper inadequate or unauthorized installation maintenance or storage or f if you violate the terms of this Agreement Any replacement Software will be warranted for the remainder of the original warranty period
187. ites being tracked Skyplot but not being used to o1 North indicator compute positions iL Horizon Satellites being used to Minimum compute positions elevation L ee 5740223 46m N 2476943 97m E Current position 31 41m HAE PDOP 2 50 PDOP WGS 1984 Datum Productivity Precision Pee Ee Que eS Filled black boxes represent satellites that the receiver is using to compute its current GPS position Unfilled white boxes represent satellites that the receiver is getting signals from but is not using because the signals are too weak In the example above eight satellites are being tracked and five of these satellites are being used to compute GPS positions Note Numbers with no box represent satellites that are available but that the TerraSync software is not receiving signals from Satellites that have an R prefix are GLONASS satellites These satellites appear only if the receiver you are using can track GLONASS satellites for example the GPS Pathfinder ProXRT receiver and the Use GLONASS option is enabled in the GPS Settings form Your current GPS position is displayed at the bottom of the screen Tip For detailed information on satellite positions and signal strengths use the Satellite information screen in the Status section To compute a 3D GPS position you need a minimum of four satellites with good geometry When you switch on the receiver it automatically starts
188. ith alphabetic characters only the last number is incremented For example if the step value is 1 and the last value was A100 K9 the next value is A100 K10 The auto incremented value is only a default value so you can edit it if you want If you do the next value in the sequence is calculated using the new value you entered not the original value generated by the TerraSync software If the TerraSync software cannot generate the next value in the sequence it creates the attribute without a value This occurs if e the feature is the first of its type to be created in this file and no default value is specified e the last value for the attribute was blank e the last value was the maximum value in the range and the sequence is incrementing e the last value was the minimum value in the range and the sequence is decrementing To make an attribute auto incrementing you must set an increment value in the data dictionary You can do this in the Data Dictionary Editor utility in the GPS Pathfinder Office software or data dictionary editor in the Data section For more information on making an attribute auto incrementing refer to the Data Dictionary Editor Help Pop up messages When the TerraSync software asks a question it displays a pop up message You must answer the question before you P s 3 Are you sure you want to can continue working with TerraSync To answer the exit TerraSync question tap one of the buttons in t
189. itions in terms of WGS 84 Note Each background image is associated permanently with a coordinate system To display correctly when opened the coordinate system of a background image must match the current TerraSync coordinate system Tip If no coordinate system has been assigned to an image when you open it in the background the TerraSync software associates it with the current coordinate system To change the coordinate system that is associated with a background image change the coordinate system of the image using Trimble postprocessing software and transfer the image to the TerraSync software again Alternatively delete the corresponding cs file in the TerraSync documents folder change to the required coordinate system in the TerraSync software and open the image in the Map background Finally if altitudes are to be stored by the GIS they need to be transformed from heights above the GRS 80 ellipsoid to heights above some other reference level The most common reference level is the geoid more commonly referred to as mean sea level The GPS Pathfinder Office software contains a geoid separation model which enables it to transform altitudes relative to GRS 80 into heights relative to mean sea level The geoid separation models used by the TerraSync software and the GPS Pathfinder Office software differ in accuracy The TerraSync software is necessarily approximate while GPS Pathfinder Office software is more accurate If you requir
190. izontal estimated accuracy of each GPS position once the data has been postprocessed in the office This prediction allows for corrections that will be applied when you postprocess the data back in the office If the estimated accuracy of any GPS position is greater than 5 meters the software will not log the position Note The estimated accuracy has a 68 confidence level which means that 68 of the time the GPS position has an accuracy equivalent to or better than the estimated accuracy shown For example if the estimated accuracy is 5 meters 68 of the time the estimated accuracy of the position is in fact 5 meters or better Tip If you need 5 m or better it would be better to select a tighter required accuracy of 3 m to ensure a higher level of confidence for example 95 1 Tap the Section list button and then select Setup 2 Tap Logging Settings 3 Tap the Setup button Ea below the Accuracy Settings field The Accuracy Settings form appears lerraSync oS Setup amp pa 4 From the Accuracy Value for Display Logging fields select Horizontal for the accuracy of the current GPS position and then select Accuracy Settings OK Cancel Accuracy Value For Display Logging Horizontal 7 Postprocessed to use the predicted postprocessed Postprocessed v accuracy l UW Postprocessing Base Distance EF 5 From the Postprocessing Base Distance field spon _ s
191. l correction message All Trimble GPS receivers use the version 2 1 or later RTCM protocol real time kinematic A real time differential GPS method that uses carrier phase measurements for greater accuracy Satellite Based Augmentation System SBAS is based on differential GPS but applied to wide area WAAS EGNOS MSAS Networks of reference stations are used and corrections and additional information are broadcast via geostationary satellites SNR The signal strength of a satellite is a measure of the information content of the signal relative to the noise of the signal The typical SNR of a satellite at 30 elevation is between 47 and 50 dBHz The quality of a GPS position is degraded if the SNR of one or more satellites in the constellation falls below 39 dBHz The TerraSync software lets you set a minimum SNR value This value is used to determine whether the signal strength of a satellite is sufficient for that satellite to be used by the GPS receiver If the SNR of a satellite is below the configured minimum SNR that satellite is not used to compute positions A site consists of an existing coordinate system plus an extra set of parameters for horizontal and vertical adjustments Together these provide the best fit of GPS data to a specific area or site Because the additional corrections are only valid for a limited area that area is called a site or local site A coordinate system is designed to apply over a large a
192. lect Waypoints From the list of files select the garbage can waypoint file and then tap Open From the waypoint list tap the garbage can waypoint to select it Tap Options and then select Set Nav Target Tap the Subsection list button and then select Navigate Wpt File W102009A Use the directional dial to help you navigate to the rni Diane 1 Garbage Can 29 76 m target 2 CImp2 27 62 m You are now at the site of the garbage can Tap the Subsection list button and then select Waypoints Tap Options and then select Close file to close the waypoint file TerraSync Software Getting Started Guide 145 5 Tutorial Collecting Data 146 Collecting the target as a point feature Now that you are at the target you can collect the GPS position as a garbage can feature and then add it to the Starfish file 1 If the file is not already open open the existing Starfish Bay data file 1 Tap the Section list button and then select Data 2 Tap the Subsection list button and then select Collect Features 3 Select Garbage_Can and then tap Create The attribute entry form for the garbage can feature appears lerraSync iv 4 Tap Log to log the GPS position 10 Garbage Can Date Visited oe ok 5 Enter the attributes for the garbage can and then __ condition tap OK to save the new feature Style Ending the data collection session When the dat
193. lename is in the format YMMDDHHR imp Note A imp file is a file in SSF format that was created by importing from a GIS CAD or spatial database It is the same as an ssf file but has a different filename extension to distinguish it from data files created in the field 7 Inthe File Name field enter Starfish imp and then click Save 8 Click OK to import the file 9 A message appears showing information about the import Click Close to close the message box The file Starfish imp is created from the selected Shapefiles The next step is to transfer this file to the field computer TerraSync Software Getting Started Guide Tutorial Collecting Data 5 Transferring data to the field computer You need to transfer the imported Starfish data file to the field computer so that you can use it in the field to update existing data Use the Data Transfer utility to transfer data between the office computer running the GPS Pathfinder Office software and the field computer running the TerraSync software L Turn on the field computer and the office computer and connect the two computers If the field computer is a laptop or Tablet PC for example make sure that there is a network connection between it and the office computer If the TerraSync and GPS Pathfinder Office software are installed on the same computer for example a laptop PC you must still transfer files between the TerraSync software data folder and the GPS Pathfinde
194. ling the earth s surface page 188 A datum transformation defines the method and parameters that are used to transform the coordinates of a point defined in one datum to coordinates in a different datum Trimble software supports several methods of datum transformation including Seven Parameter Three Parameter also referred to as Molodensky and grid based transformations Typically you use datum transformations to convert data collected in terms of the WGS 84 datum using GPS methods onto datums used for mapping purposes in individual regions and countries See magnetic declination See real time differential GPS 212 TerraSync Software Getting Started Guide differential correction differential GPS digitizing Dilution of Precision DOP EGNOS ellipsoid feature field computer geoid Glossary Differential correction is the process of correcting GPS data collected on a rover with data collected simultaneously at a base station Because it is on a known location any errors in data collected at the base station can be measured and the necessary corrections applied to the rover data Differential correction can be done in real time or after the data has been collected by postprocessing See real time differential GPS The process of creating positions manually by selecting a point on a map DOP A measure of the quality of GPS positions based on the geometry of the satellites used to compute the positions
195. lt a warning is indicated by a sound with falling tones The following table lists events and conditions in the TerraSync software and the sounds that are used for them Event Sound Description category Feature stored Success The feature has been successfully stored GPS connected Success The TerraSync software has successfully connected to the GPS receiver and is receiving position information GPS OK Success The GPS quality has increased to the levels you have specified and the TerraSync software is logging positions again Minimum Success The TerraSync software has logged the minimum number positions stored of positions for the current feature You can now safely close this feature and begin logging another feature Navigation Success The navigation target is within the close up range you proximity alarm have specified and the Direction Dial screen changes to the Close up screen Position logged Success The TerraSync software has successfully logged a GPS position Position snapped Success The digitized position has been snapped to a nearby existing position Real time OK Success The connection to the specified source of real time differential correction has been regained Carrier lock Success Carrier lock has been acquired The TerraSync software has acquired started logging carrier or H Star data General error System An error has occurred An error is indicated by the sound the field computer uses for the
196. ltipath environment You will also learn other advanced techniques such as segmenting lines and nesting a collection of features within other features For more information about these techniques see Appendix A Advanced Datalogging Options Note You can choose to skip this exercise and go to straight to Exercise 4 Processing the data on page 118 to process the data you have already collected Q Reopening a data file for continuation of data collection For this exercise you return to Starfish Bay to collect new data requested by your supervisor This means that you will open the Starfish Bay data file you created earlier and make changes and additions to the data previously collected To reopen the data file 1 Tap fH and then select Programs TerraSync to start the TerraSync software 2 Tap the Section list button and then select Data TerraSync 3 Tap the Subsection list button and then select Existing Files Existing Choose Existing Data File 4 Tap the Starfish file to select it and then tap Open Lot Default z Name Start Time Size R102820A 10 28 09 08 42 pm 2 KB 5 Ifprompted to confirm the antenna height tap 10 28 09 08 43 pm _ 55 KB OK or change the settings if you are using different equipment to the equipment you used to collect the previous data 6 The Existing Features screen appears This screen Features 196 Positions 460 shows all the features you have alread
197. m UTM Zone 10 North Datum NAD 1983 Conus Le Le Le EGM36 Global 4 From the Select By group select the appropriate option for sending a coordinate system or a site 5 Select the options in the Site System Zone and Datum fields that match the coordinate data you want to send Some of these fields are read only or hidden depending on the selections in other fields 6 Click OK The Coordinate System dialog disappears The selected coordinate system or site is added to the Send list in the Data Transfer dialog 7 Click Transfer 8 Ifthe selected coordinate system references other files such as geoid grid files the Associated Files dialog appears Select the appropriate check box to send each file required and then click OK The selected coordinate system and associated files are transferred to the field computer replacing any coordinate systems stored in the TerraSync software TerraSync Software Getting Started Guide 195 B Coordinate Systems For more information refer to the GPS Pathfinder Office Software Online Help Configuring coordinate systems Use the Coordinate System form to edit the coordinate system zone and datum parameters The TerraSync software lets you specify a datum transformation and a map projection so that you can see your GPS position Coordinate System OK Cancel lerraSync eo ff a and the position of features you collect in your l
198. m The recommended UTM datum for the U S A is NAD 83 You have defined a custom coordinate system datum and or zone incorrectly in the Coordinate System Manager utility in the GPS Pathfinder Office software Check the definition of the coordinate system datum and or zone carefully You cannot select some coordinate system datums zones or ellipsoids The target icon is not at the location of the feature you selected as the navigation target You transferred a single coordinate system to the TerraSync software or a coordinate system export file that did not include all the coordinate systems you want When you transfer coordinate systems to TerraSync the transferred data overwrites the existing data so you must make sure that you transfer all the coordinate systems you require Create a coordinate system export file that contains all the coordinate systems that you want to use and transfer this file to TerraSync The required coordinate system files have been deleted from the field computer You re recorded the GPS position of the feature or digitized its position The navigation target remains at the old position of the feature Transfer the files from the GPS Pathfinder Office software again To restore default coordinate systems re install the TerraSync software Reselect the feature as the navigation target The message The system time of this device does not match GPS time appea
199. main The value selected is called the attribute value An attribute is the particular value for a feature chosen from the domain of an attribute For example for a road feature surface type is an attribute bitumen gravel and concrete are domains and gravel is an attribute value Also called a reference station A base station is a GPS antenna and receiver positioned on a known location specifically to collect data for differential correction Base data needs to be collected at the same time as you collect data on a rover unit A base station can be a permanent station that collects base data for provision to multiple users or a rover unit that you locate on known coordinates for the duration of the datalogging session A baud is a unit used to measure the speed of electronic code transmissions generally one bit per second The higher the baud rate the faster the transfer of data However both the input and output device must be configured to the same baud rate for data to be successfully transferred A bearing is the direction from one point to another usually measured clockwise from north In the TerraSync software the bearing indicates the direction from your current position to the target A broadcast server is an Internet server that manages authentication and password control for differential correction sources such as virtual reference station VRS network networks and relays corrections from the source that you select An
200. mber is limited only by storage space on the field computer Squid Way To continue a line feature L D o w nN In the Collect Features screen select the Path feature Make sure Log Later is selected To do this tap Options and then select Log Later Tap Create In the Name field enter Squid Way Tap Log and then start traveling along Squid Way When you reach the duck pond tap OK to close the Squid Way feature The Collect Features screen reappears In the Collect Features screen select the Waterbody feature and then tap Create Move to the perimeter of the pond and then tap Log to begin logging the pond Walk around the perimeter of the pond When you reach the starting point tap Pause In the attribute entry form enter the attributes for the pond and then tap OK TerraSync Software Getting Started Guide 113 5 114 Tutorial Collecting Data 10 11 12 13 Tap Options and then select Continue The Continue Feature form appears listing the line and area features that are available for continuation in the order they were collected Tip The feature name is the name of the feature class The attributes below the list of features shows the name entered for the feature In the Continue Feature form select the Path feature and then tap Continue The attribute entry form for Squid Way appears Return to where you last logged a position for Squid Way and then tap Resume to continue to
201. mbol is over the top of the target symbol Note Ifyou are using Autonomous GPS the position may jump around on the screen Tip In the Close up screen your heading is not updated Rather than turn it is best to face the direction that you were originally moving in and then move sideways backward or forward TerraSync Software Getting Started Guide 141 5 Tutorial Collecting Data Updating a feature You have opened the existing file and navigated to the road sign feature Now you can edit the attributes To update the attributes for a feature 1 Tap the Section list button and then select Data 2 Tap the Subsection list button and then select Update Features The Update Features screen appears 3 If the traffic sign you navigated to is not the selected feature in the list select it now 4 Tap Begin to open the attribute entry form for this feature Use this form to update the attributes TE TerraSync qn 45 ee The Date Visited attribute has been set up to 2 ai Sign auto generate on update As soon as you make pate yieied any change to the attributes or position of the u No U turn feature this attribute is automatically updated uses Needsireplacing Image file with today s date 5 The next attribute is the sign type Use the Type attribute to verify that you are updating the correct sign Check that the real sign matches the type recorded in t
202. meone else at your company registered the software ask them for the installation code If you cannot find out who registered the software send an email containing the Proof of Purchase Number POPN for your copy of the software to Trimble_support trimble com e Ifyou registered your copy of the software yourself you can check your installation code from the My Trimble page of the Trimble website To do this a Open your Web browser and go to www trimble com register Your default Web browser opens and displays the My Trimble account login page Trimble Navigation Central Authentication Service Windows Internet Explorer 00r 6 A x httpsiyiogin trimble com cas login service http 3a zf 2fsup Y B Xx P File Edit View Favorites Tools Help Google microsoft device controler MDC vista search D SB Gee Bre gy Bookmarks gt Oson 7 7 We Be Trimble Navigation Central Authentication Service M D dh E pae G Tools A Trimble Central Authentication Service Enter your e mail address and password For security reasons please Log Out and Exit your web browser when you are done accessing services that E mail require authentication Password Create an account Forgot password Click here to send us an email Version 1 7 copyright 2007 2009 Trimble Navigation All rights reserved Powered by JA SIG Central Authentication Service Copyright 2005 2009 JA SIG All rights reser
203. method Bluetooth port Use the Bluetooth management software provided with your field computer and the GPS receiver to configure and then establish the Bluetooth wireless connection Standard RS 232 serial Connect the GPS receiver cable to the curly straight through cable COM port Trimble recommends that you use the cable with P N 45052 to protect the field computer from power supplied by the receiver Connect the curly straight through cable to the field computer Customized serial COM Connect the GPS receiver cable to the null modem adaptor port P N 43197 The adaptor changes gender and also protects the field computer from power supplied by the receiver Connect the null modem adaptor to the data download cable that was supplied with the field computer Connect the data download cable to the field computer CompactFlash serial port Connect a CompactFlash serial adaptor to the CompactFlash port Then connect as for a standard COM port Note A field computer uses more power when a GPS receiver is connected to its CompactFlash serial port This type of connection will discharge the battery in the field computer more quickly Powered connections CAUTION Using COM port cabling that supplies power to the field computer can cause problems with or even permanent damage to the field computer Some GPS receivers supply power and some cables transfer power through one or more of their pins Trimble strongly recommends that you p
204. mputer powered by the Windows Mobile version 5 0 software or version 6 operating system 000 43 Installing the TerraSync software onto a Windows computer 04 43 Updating the TerraSync software 6 ee ees 47 Compatible GPS r ceivers sesa ca eG oe Eg ee Ow bala ala ee ee 47 Connecting toa GPS receivers oe ek koa ee oet ER EWS ES eR eS 48 Connecting to external real time correction devices 00000005 49 3 User Interface and Data Entry 2 222 20222222 0es 51 Gein Nelo si Stir ea e whe aaa ede Bat Gas ee ahaa aoa Warn Beat acne eae 52 Using the Windows operating system asaur 52 Using the Windows Mobile operating system noana aaea 53 Adjusting the backlight ossa 4444 eneret a ee 4 oo RG a oe Oe Ee anes 53 Working with other applications 6 ee ee 53 On screen keyboards 0036 cS ee ee RR Ge Ree ee eS 54 Device Lock itility ioc a cane SE EE A Ree SA dee ea ys 55 Starting and exiting the TerraSync software unas ee ee 56 S ction Str CTU TE issada een oe GE e A a he Aw A EE Be ee wn SS 56 TerraSync Software Getting Started Guide 7 Contents The TerraSync software display 0 0 cee ee ene 57 Status babce wi bad CEOS SG Hee aed oe Bee e ae eee we Sed 57 Interacting with the TerraSync software 1 0 cee eee 62 SCVEENS aeon nls SARA ESL ot ee 4 Dae Hah ae eR URIS ee eo hs 62 Graphical SCr ET Ssss 2 beeen a ed De Wa bed ewe ded bake A beds 63 POVINS inaa ee
205. ms have been established that best suit particular regions For example maps in the United States are often based on the North American Datum of 1927 or 1983 NAD 27 NAD 83 The only global datum is WGS 84 which is based on the GRS 80 ellipsoid All GPS coordinates are based on the WGS 84 datum surface Datum fitting Europe Earth s surface Datum fitting North America Figure B 7 Comparing datums A coordinate system is a three dimensional reference frame used to describe the location of objects within a spatial reference system a datum There are two types of global coordinate systems e Angular coordinates for example Latitude and Longitude e Cartesian rectangular coordinates for example Universal Transverse Mercator In the Latitude and Longitude coordinate system position coordinates are based on an angular distance from a known reference point the Prime Meridian located at Greenwich Coordinates are expressed in degrees minutes and seconds Angular coordinates are unprojected as they are perfectly suited to the spherical surface of the earth Latitude and Longitude is the predominant coordinate system used for nautical and aeronautical navigation For most land based GPS applications and particularly for GIS data collection applications latitudes and longitudes are much less convenient Typically a GIS represents the coordinates of geographic features in a locality of interest using a rectang
206. n your Windows Mobile device has been activated lt Back Cancel 40 TerraSync Software Getting Started Guide Software Installation and Activation 2 Offline activation 1 Print out or write down the information that appears Activation Wizard See Offline Activation Please provide the following information to your Trimble reseller or select Back to retry the Internet connection Software Serial Number 564533 00110 Device Name Trimble GeoE xplorer Series Device ID 9425F2402D58F 441 939E 41484244 2F1466DA568A Device Serial Number 8766453312 2 Send the information to your Trimble reseller Activation Wizard ra gt Trimble Completed Please run the Activation Wizard again once you have received the Activation Key lt Back Cancel Your Trimble reseller will return the Activation Key on an electronic media diskette CD SD card or USB memory stick Insert the media into the office computer that is connected to the field computer Activation continues as for Activation using an existing Activation Key TerraSync Software Getting Started Guide 41 2 Software Installation and Activation Activation troubleshooting One of the following issues may occur e No valid Installation Code Activation Wizard Trimble Enter Installation Code The Installation Code you have entered is invalid 960625 00110 09100 56AB45E3 Please enter another Installation Code e
207. nate system export files creating 193 transferring 194 Coordinate System Manager utility 193 coordinate system selecting for import 131 coordinate systems supplied with TerraSync 192 CoPilot Live 7 Professional 185 CoPilot Live 7 Professional navigation software 81 128 Correction Datum field 168 171 counter 158 creating new data file tutorial 100 criteria for filtering 139 critical power level 60 cross track error definition 212 cross track line definition 212 customizing sounds 76 data collecting new features 100 differentially correcting 120 updating existing features 137 data dictionary definition 212 overview 93 selecting tutorial 100 transferring to TerraSync 133 Data Dictionary Editor utility 128 data entry date fields 71 Image file fields 71 menu fields 70 overview 69 text fields 69 time fields 70 data files exporting to GIS 126 opening 138 transferring from the field computer 118 viewing in GPS Pathfinder Office 125 Data section logging positions later 102 overview 80 setting navigation target tutorial 140 Data Transfer utility transferring coordinate system export files 194 transferring files from the field computer 118 transferring files to the field computer 133 data update preparing for 128 date fields 71 datum local 216 of correction source 168 171 transformation 189 191 212 datums available 192 changing 196 definition 212 declination definition 216 decrementing attribute value
208. nd Mexico A waypoint is a geographical point that unlike a feature holds no attribute information beyond a name and location Typically waypoints are used to denote objects whose locations are of primary interest such as a survey mark Waypoints are most often used for navigation An Internet site that lets users download GIS data background and other files for a specified geographical area The TerraSync software can download raster background files from a Web map server WGS 84 is an abbreviation for World Geodetic System 1984 WGS 84 has superseded WGS 72 as the datum used by GPS since January 1987 The WGS 84 datum is based on the ellipsoid of the same name A small handheld device powered by the Windows Mobile operating system A Windows Mobile powered device usually has a small screen and limited memory and storage space TerraSync Software Getting Started Guide 221 Glossary 222 _ TerraSync Software Getting Started Guide Index Symbols cse files 194 imp files 132 ssf files 132 wav files 76 Numerics 3D GPS position 96 5800 GPS receiver 48 148 A accelerator keys 66 account My Trimble 20 24 Activation Wizard 37 ActiveSync technology 18 Address field 168 almanac definition 211 altitude converting 191 antenna enter height 100 icon 58 tooltip 60 area features collecting 103 108 collecting point features as well 175 continuing 175 offsets 176 associating data dictionary with new data file 100
209. nd Satellite Information screen in the Status section e The Direction Dial and Close up screens in the Navigation section Start moving e The map display in the Map section zarowno Hjem f Turn 61 Head 138 T Forms OK button Cancel button Title 198 Road Sign Separator field __ Date Visted Current field Type Label 1condition Good Value Image file b To enter data in the TerraSync software you use a form Like a paper form a software form has a title and a sequence of lines or fields Each field on a form generally has two parts a label or name and a value A label is followed by a colon which separates it from the value Some fields are separator fields which have no value and serve simply to divide a form into sections If there is a dark rectangle around a field and its label it is the current field on the form Any editing operations apply to the current field To edit a field select it There are several ways to enter data into a form depending on the keyboard options the field computer has and the type of data stored in the field See also Data entry fields page 69 To move to the next field on a form do one of the following e Tap the field you want to move to Tap Enter on the on screen keyboard Tap Enter repeatedly to move through all fields on the form TerraSync Software Getting Started
210. nd intsmationel copyright trademark and patent laws as described in Status About 4 Select the install option for the type of device that you have connected The Choose Setup Language dialog appears Choose Setup Language a Select the lanquage for this installation from the choices below oT English United States v 5 Select the language that you require to run the installation To run the rest of the TerraSync software in a language other than English after installing the software you must download the appropriate language update from http www trimble com terrasync_ts asp For more information see Step 15 below 6 Click Next 7 The TerraSync software installation wizard appears Click Next 8 Read the software license agreement and then click Yes to accept it 32 TerraSync Software Getting Started Guide Software Installation and Activation 2 The Register your Software page appears TerraSync 4 10 for Windows Mobile InstallShield Wizard Register your software To install TerraSyne you must enter a valid Installation Code To obtain an Installation Code use the proof of purchase number to register your copy of the software over the Internet The proof of purchase number is displayed on the TerraSyne CD packaging You must connect to the Internet to register If you do not have Internet access contact your Trimble dealer have already registered and have a valid Installation Code
211. nding half of the battery is yellow e When the power level is critical the corresponding half of the icon is red and the icon flashes If the GPS receiver is powered by the field computer for example a GPS Pathfinder XC receiver or is integrated with the field computer for example a GeoExplorer series handheld both halves of the battery icon show the same level and indicate the battery status of the field computer Y R Filter icon Indicates that a filter has been applied to the open data file When this icon is not displayed no filter has been set up For more information refer to the TerraSync Software Help TerraSync Software Getting Started Guide User Interface and Data Entry 3 Table 3 1 Status bar Icons continued Icon Name Description Ficm Estimated Shows the estimated accuracy of the current GPS position The type of estimated Accuracy icon accuracy value shown depends on the settings in the Accuracy Settings form ls Logging icon The estimated accuracy value may be the estimated accuracy in the field or it may be the predicted accuracy after postprocessing To show the predicted postprocessed accuracy there must be a data file open and the software must be logging GPS positions By default this icon shows the estimated accuracy in the field For more information about the predicted postprocessed accuracy value see predicted postprocessed accuracy page 218 The direction of the arrow in
212. ndows Mobile operating system you are using For help on using this software select Help from the Start menu on the Windows Mobile powered device For information about some Windows Mobile software features that are useful when using the TerraSync software see e Adjusting the backlight page 53 e Working with other applications page 53 e On screen keyboards page 54 e Device Lock utility page 55 Adjusting the backlight You can change the backlight brightness on any device powered by a Windows Mobile operating system to adjust to indoor or outdoor operation For information on changing device settings refer to the documentation for the device Working with other applications The Windows Mobile operating system is similar to a desktop Windows operating system You can use the same methods on the device as you would on a Windows computer to start exit or switch between programs For example to switch from the active application to another application tap the program icon in the taskbar Alternatively if the device has a keyboard you can use the ait key combination Some programs on a Windows Mobile powered device do not have a close button or a menu command for exiting the program Instead you must use system software to shut down a particular program If the device does not have a keyboard you must also use system software to switch from the active application to another application To shut down or switch to a task th
213. nection tab and check that the Allow connection with desktop computer when device is attached check box is selected Another application is using the COM port Exit the other application or disconnect it from the COM port You cannot send or receive data files by email from within the TerraSync software The TerraSync software cannot connect to your ISP because it does not have your account login details In the settings for the email service that you are using specify the login details for connecting to your ISP The data files attached to emails are not being downloaded from the mail server Configure the email service that you are using to download the entire message and any attachments not just the message header The field computer does not support email Use the Trimble Data Transfer utility to transfer files to or from the TerraSync software 202 TerraSync Software Getting Started Guide Field computer This section lists describes problems you may encounter when using a field computer Troubleshooting D Problem Possible cause Solution The field computer does not turn on or turns off immediately after being turned on The field computer s batteries are dead Replace or recharge the field computer batteries Connect to an external power source The message Not enough memory appears Not enough memory on the Windows Mobile powered device
214. ns Use the Logging Settings form to enable between feature logging If the nterval field contains a time or distance value then between feature logging is enabled If the nterval field is set to Off then between feature logging is disabled For more information refer to the TerraSync Software Help Between feature positions can be spaced by distance or time For example use the distance option to force the TerraSync software to log a position every three meters you travel or use the time option to log a position every five seconds To set the logging interval select the logging style Distance or Time in the Style field and then enter the rate in the Jnterval field If between feature logging is enabled the TerraSync software logs positions at the specified rate whenever you are not logging positions to a feature Note As the name implies between feature logging only logs positions once a feature has been collected or updated Creating or opening a data file does not initiate logging of between feature positions Continuing line and area features When recording a line or area feature you could come across another feature that you need to record The feature may be adjacent to the line area feature or it may be some distance away When collecting a path line feature for example you might encounter a gate point feature You do not have to record the entire path and then return to record the gate Simply end the path feature
215. nt that is stored in a separate file A waypoint is a position coordinate that you can navigate to For this tutorial you will use the waypoint to map a position for a future garbage can 104 TerraSync Software Getting Started Guide Tutorial Collecting Data 5 Creating a waypoint You are in Starfish Park looking for good positions for the new garbage cans As they are not yet installed you cannot add them as a feature but you can locate good positions where they should be installed These positions are gathered as waypoints The waypoints will be collected in a single waypoint file and provided to the garbage can installation crew Once the garbage cans are installed you can use the same waypoint file to navigate back to these positions and then collect the garbage can features Before you can create a waypoint you must create a waypoint file 1 Tap the Section list button and then select Navigation 2 Tap the Subsection list button and then select Waypoints The Waypoint Files screen appears 3 Inthe Waypoint Files screen tap New The Create Waypoint File form appears Garbage 12 31 69 05 466 B 4 Inthe File Name field enter Garbage Cans and then tap OK Find a suitable place for the garbage can and then create the waypoint that stores that location 1 Inthe Garbage cans file tap Options and then select New The New Waypoint form appears 2 Inthe Name field enter
216. ntenna not to the distance from the ground to the antenna You can use a configuration file to do this e Keep the laser rangefinder as close to the antenna phase center as possible when shooting e Shoot at a higher position on the feature to compensate for the antenna height being subtracted from the altitude of the feature For more information on configuring a laser rangefinder to work with the TerraSync software refer to the TerraSync Software Help You can also use a laser rangefinder as an external sensor see below Using an external sensor You can use an external sensor with the TerraSync software Note This option is not available in the TerraSync software Standard edition The data recorded by the sensor can be stored as an attribute or it can be stored in the data file as an uninterpreted sensor data record You can export uninterpreted sensor data from the GPS Pathfinder Office software to the GIS or processing software Depending on the way you want to store the sensor data and the capabilities of the sensor you can configure the TerraSync software to read data from the sensor at specified intervals or only when you request it TerraSync Software Getting Started Guide Advanced Datalogging Options A Note A laser rangefinder can be used either as an external sensor as described here or to supply data for feature offsets See Using a laser rangefinder to record offsets page 182 Repeating features Use
217. o sort the Choose Feature list by feature name tap the Name column heading X Tip If the list is already sorted by the column you tapped tapping the column heading reverses the sort order 64 TerraSync Software Getting Started Guide Buttons Many forms and screens in the TerraSync software contain buttons When you tap a button the TerraSync software carries out the appropriate command or opens anew screen For example if you tap GPS Settings in the Setup screen the GPS Settings form appears List buttons and menu buttons are special buttons They can be identified by the drop down arrow at the right end of the button When you tap one of these buttons a drop down list of commands appears See also List buttons page 65 and Menu buttons page 66 List buttons User Interface and Data Entry 3 Current Configuration Factory Defaults Reload l Change Logging A Real time Settings GPS Settings Settings Coordinate Uni External nits System Sensors List buttons are buttons that have a vertical line and a drop down arrow at the right end of the button Section list button Subsection list button Create New Data File Create File Type Location File Name Default v starfish Dictionary Name Seaview 7 Use list buttons to move to a different section or subsection of the software or to
218. ocal Select By Coordinate System and Zone coordinate system This makes it easy for you to check _ system your position or to navigate using a map produced by Y your GIS Datum WGS 1984 T To configure the Coordinate System form R LI Height Above Ellipsoid HAE 1 From the Setup section tap Coordinate System Altitude Units Meters vjje The Coordinate System form appears 2 Use this form to specify the coordinate system site zone datum and altitude reference You can also specify the units used to display the coordinates and altitude 3 Tap OK when you have finished The Coordinate System form closes and any changes made are applied immediately throughout the TerraSync software If any points in the Map section are not within the selected coordinate system a warning message appears asking you to confirm that you want to apply the new coordinate system If you do the map points that are outside this system are not displayed on the map 196 TerraSync Software Getting Started Guide CHAPTER Setting up a Base Station In this chapter This chapter contains detailed information about setting up a base station Em Introduction m Logging base data to a file TerraSync Software Getting Started Guide 197 c Setting up a Base Station Introduction You can use the TerraSync software to configure a GPS receiver as a base station Depending on the type of GPS rec
219. oid definition 214 height antenna 100 Help 14 52 horizon definition 214 Horizontal Dilution of Precision definition 215 H Star technology postprocessed configuring the TerraSync software 155 real time configuring the TerraSync software 155 collecting high accuracy data 156 data 75 76 processing options 121 workflow and infrastructure 154 l icons in status bar antenna 58 base logging 59 battery 58 connect 57 digitizing 59 external RTK 58 filter 58 integrated RTK radio 58 logging 59 logging static 59 logging vertex 59 memory 59 pause 59 real time beacon 58 real time external 58 real time external beacon 58 real time satellite 58 real time SBAS 58 satellite 57 image file attributes 185 import imp file 132 Import utility 130 incrementing attribute values 73 installation code 23 25 33 46 integrated beacon receiver real time tooltip 60 integrated beacon troubleshooting 205 integrated camera 185 integrated RTK icon 58 tooltip 60 integrated RTK radio using to receive RTK corrections 160 integrated satellite troubleshooting 205 integrated SBAS troubleshooting 205 ionosphere errors associated with 163 ionospheric noise definition 215 J jpg image file 185 Juno SB handheld 47 Juno SC handheld 47 Juno series handheld 99 Juno ST handheld 47 K keyboard accelerators 66 on screen 54 shortcuts 66 Trimble numeric 55 L L1 215 L2 215 labels in forms 63 landscape orientation 12 langua
220. on Information fields Note In this view the centre of the screen is your current position This screen is not depicted North Up but is Heading Up TerraSync Software Getting Started Guide Tutorial Collecting Data 5 To navigate to the selected target start moving This enables the TerraSync software to calculate your initial heading When the direction dial shows the turn arrow keep moving and turning until the arrow points to the top of the screen The top of the screen indicates your current heading Then move towards the target adjusting your direction to ensure you are always heading toward the target Note If you are moving very slowly or are stationary the direction dial is not updated The message Heading locked appears When you are within a few meters of the target the view switches to the Close up screen f i 2 Traffic Si ions Note The top of the screen is the direction you were e Ee travelling in when the directional dial changed to the close up screen By default in this view the target is at the centre of the close up screen 2 2 Traffic Sign In the Close up screen your position is indicated by the cross X and the target is represented by the bull s eye E Dist 1 39 m M Bear 169 T As you move closer to the target the position symbol Turn 2 Head gets closer to the target symbol You have reached the target when the position sy
221. on source in the Choice 1 field The integrated beacon component Pro XRS receivers only does not appear to work You have set the real time source incorrectly In the Real time Settings form see page 88 set one of the Choice fields to Integrated Beacon If integrated beacon is your preferred correction source set the Choice 7 field to Integrated Beacon You have set the mode or frequency incorrectly In the Real time Settings form see page 88 select appropriate options in the Mode and Frequency fields The integrated OmniSTAR component ProXRT and Pro XRS receivers only does not appear to work You have set the real time source incorrectly In the Real time Settings form see page 88 set one of the Choice fields to Integrated OmniSTAR If integrated OmniSTAR is your preferred correction source set the Choice 1 field to Integrated OmniSTAR You have entered the incorrect provider satellite and or frequency In the Real time Settings form see page 88 select appropriate options in the Service Provider Name and Frequency fields Your OmniSTAR subscription has expired or has not yet been activated In the Integrated OmniSTAR Settings form see page 87 check the expiry date of the subscription The real time differential correction link does not appear to work The telemetry link has been incorrectly installed powered cabled or configured Install the telemetr
222. ons to help you master the main concepts and tasks m Tutorial structure involved in using the TerraSync software m Tue genario This tutorial will take you approximately two Exercise 1 Preparing for data hours to complete collection Exercise 2 Data collection Exercise 3 Advanced data collection Exercise 4 Processing the data Exercise 5 Preparing for data update m Exercise 6 Data update TerraSync Software Getting Started Guide 89 5 90 Tutorial Collecting Data Tutorial structure The tutorial is divided into six exercises Three of the exercises are performed in the office using office processing software and three of the exercises are performed in the field using the TerraSync software This tutorial uses the GPS Pathfinder Office software as the office processing software For a tutorial that uses the GPS Analyst extension for ESRI ArcGIS software as the office processing software refer to the GPS Analyst Extension Getting Started Guide To successfully complete the tutorial field work you must have access to an open space outdoors free of obstructions such as trees and buildings The first four exercises of this tutorial relate to data collection Exercises five and six relate to updating data that has already been collected The office processing exercises are indicated by field exercises are indicated by Data collection Exercise 1 Preparing for data collection page 92 D Exercise 2
223. or information on the fields in the settings form refer to the TerraSync Software Help 6 Tap OK to close the correction source settings form and return to the Real time Settings form TerraSync Software Getting Started Guide 135 5 136 Tutorial Collecting Data 7 Specify up to four choices for real time corrections If your first choice is not available the TerraSync software automatically uses the second choice until the first choice is available again This occurs at all levels so the TerraSync software uses your preferred correction source at all times 8 Tap OK to close the Real time Settings form Note When you use a real time differential correction source there may be times when you cannot receive corrections Any positions logged during these times are uncorrected and are subject to errors which degrade their accuracy However you can also postprocess your GPS data in the GPS Pathfinder Office software to improve the accuracy of the real time corrected positions D Checking the real time status Always check the real time status before navigating to existing features Tip Use the status bar to quickly check the real time status When the TerraSync software is receiving real time corrections a real time icon appears in the status bar The icon flashes if there is a problem with the real time source To check the real time status Real time icon 1 Tap the Section list button and then select Status MOE
224. ork select External Source TerraSync Software Getting Started Guide High Accuracy Data Collection 6 Tap the Setup button Ea beside the Choice 1 field to configure the correction source If you selected Integrated RTK Radio the RTK Radio Settings form appears Select the radio channel and the base radio type at the correct wireless data rate and then tap OK If you selected External Source the External Source Settings form appears To use a data radio connected to the receiver select Receiver Port in the Connection Method field and then select appropriate settings for the other fields To use corrections from a VRS network select appropriate settings depending on the server and the communication method used see Using corrections from a VRS network page 163 When you have finished configuring the external source tap OK From the Choice 2 field select Wait for Real time Tap OK to confirm the real time settings and return to the main Setup screen Configure the required accuracy settings a b In the main Setup screen tap Logging Settings Tap the Setup button Pal below the Accuracy Settings field The Accuracy Settings form Setup 7 appears TerraSync eo ff a From the Accuracy Value for Display Logging 8602S Settings OK j Cancel fields select the parameters that the OURS SUSE Ee i Horizontal x TerraSync software will use to determine the a In
225. ormally as you travel If you want to record only averaged vertices use the Log Later function to pause logging before you open the feature Logging starts automatically when you open the Vertex form and returns to its former state when you close the Vertex form Using Log Later ensures that positions are only logged when the Vertex form is open See Log Now and Log Later page 174 TerraSync Software Getting Started Guide Advanced Datalogging Options A Enhanced support for adding image files as attributes to features On Trimble handhelds with integrated cameras mace ne TerraSync software version 3 30 and later includes EE N l PIC a Camera button Sin the attribute entry form gt for Image file attributes The Camera button launches the camera directly from within the TerraSync software and the resulting photo is automatically selected as the image to attach to the feature On all devices thumbnails of the selected image are now displayed in the attribute entry form when using an Image file attribute Tap the thumbnail image to open and review the image Image file GPS information is added to the EXIF header when images are attached When a jpg image file is attached to a feature and there is a current GPS position the EXIF header of the image file is populated with the following fields e GPS Time and Date e GPS Latitude Longitude Altitude and Datum e Feature name e Labels 1 and 2 as defined in t
226. ornia and applicable United States Federal law without reference to conflict of laws principles or provisions The United Nations Convention on Contracts for the International Sale of TerraSync Software Getting Started Guide 5 Goods will not apply to this Agreement Jurisdiction and venue of any dispute or court action arising from or related to this Agreement or the Software shall lie exclusively in or be transferred to the courts the County of Santa Clara California and or the United States District Court for the Northern District of California You hereby consent and agree not to contest such jurisdiction venue and governing law 4 2 Section 4 1 notwithstanding if you acquired this product in Canada this Agreement is governed by the laws of the Province of Ontario Canada In such case each of the parties to this Agreement irrevocably attorns to the jurisdiction of the courts of the Province of Ontario and further agrees to commence any litigation that may arise under this Agreement in the courts located in the Judicial District of York Province of Ontario If you acquired this product in the European Union this Agreement is governed by the laws of The Netherlands excluding its rules governing conflicts of laws and excluding the United Nations Convention on the International Sale of Goods In such case each of the parties to this Agreement irrevocably attorns to the jurisdiction of the courts of The Netherlands and furthe
227. ort From Data File dialog appears 4 Select the Starfish ssf file and then click Open TerraSync Software Getting Started Guide Tutorial Collecting Data 5 The Import From Data File dialog closes and you are returned to the main Data Dictionary Editor window where a new unsaved data dictionary has been created Select File Save The Save As dialog appears The default filename for the new data dictionary is Seaview ddf Navigate to the default project folder GPS Projects and then click Save In the Data Dictionary Editor window select File Exit TerraSync Software Getting Started Guide 129 5 130 Tutorial Collecting Data importing data from a GIS into the GPS Pathfinder Office software Before going into the field transfer the required information from the GIS to the TerraSync software The Import utility in the GPS Pathfinder Office software converts data from a GIS data format into the SSF format required by the TerraSync software L Start the GPS Pathfinder Office software and then open the TerraSync Tutorial project Start the Import utility In the GPS Pathfinder Office software select Import from the Utilities menu The Import Utility dialog appears E import Ele w Input Files Folder C Export o Selected Files Cancel Park shp Browse Road shp Browse Help Traffic_ shp Output File C TerraSyne Tutorial 702081 4b imp Browse Choose an Import Setup Sample ESR
228. owever over limited areas and depending on the accuracy required a simple ellipsoidal model of the earth s gravity fits quite well An ellipsoid is a three dimensional surface shaped like a squashed sphere which approximately models the shape of the earth TerraSync Software Getting Started Guide Coordinate Systems B Minor axis Major axis Figure B 5 An ellipsoid An ellipsoid treats the earth as a smooth featureless sphere and approximates the shape of the earth at sea level without regard to land masses The size and shape of the best fitted ellipsoid as well as its location relative to the center of mass of the earth differs from place to place As a result many local ellipsoids have been created to fit the geoid in different parts of the world Figure B 6 provides a representation of these different models for the earths surface The earth s surface ee ee ee The local ellipsoid ct A The GRS 80 ellipsoid WGS 84 datum ee Figure B 6 Models of the earth s surface A datum transformation and a projection are then used to transform coordinates from this local ellipsoid to the flat earth model used in maps and in the GIS TerraSync Software Getting Started Guide 189 190 Coordinate Systems Coordinate systems and datums A datum specifies the ellipsoid used to represent the earth and the point on the surface of the earth that is used as the origin of the datum Various datu
229. p Options and then select Log Later 3 From the Choose Feature list select Road 4 Tap Create The Road attribute entry form appears Note When you use the Log Later option the pause icon Wi flashes in the status bar to let you know that the TerraSync software is not logging GPS positions 5 The Name field is already selected Enter the name of the road Seagull St 6 Seagull Street has two traffic lanes The Number of Lanes field is set to 2 by default so you do not need to change this field 7 Fill out the other attributes as required 8 MovetothestartoftheroadandthentapLogo nE TerraSync en 42 ok begin logging GPS positions for the road feature The pause icon disappears from the status bar and the number on the logging icon increments as each position is recorded 9 Continue down the road When you reach the Number of Lanes 2 end of the line you are logging tap OK to save the _ surface Asphalt M feature and return to the Collect Features screen Condition z oK Tog 102 TerraSync Software Getting Started Guide Tutorial Collecting Data 5 Collecting an area feature Now you need to record the park in Starfish Bay This is an area feature To record an area feature you must travel around the perimeter of the area As you travel the TerraSync software logs GPS positions at the logging interval set in the data dictionary The first and last GPS posit
230. pecify the text or number you want to enter As you enter characters they appear in the selected field An on screen keyboard may provide keys for you to tap or may accept handwriting which it interprets as text If you use an on screen keyboard to enter values the TerraSync software automatically moves the focus to the next field on the form To move through the fields on a form repeatedly tap Enter on the on screen keyboard If the field computer has a physical keyboard press the Tab key to move through the fields When you reach the end of the form the focus moves to the first field on the form See On screen keyboards page 54 Text To enter a value in a text field use an on screen keyboard or the physical keyboard If you are using a field computer with on screen keyboards a keyboard pops up automatically when you select a text field The keyboard that pops up is the one that was selected when you started the TerraSync software See On screen keyboards page 54 Numeric To enter a value in a numeric field use an on screen or physical keyboard If the field computer uses on screen keyboards the Trimble numeric keyboard see page 55 pops up when you select a numeric field Tip Any text or numeric field can be defined as an auto incrementing attribute See also Auto incrementing attributes page 73 TerraSync Software Getting Started Guide 69 3 70 User Interface and Data Entry Menu A menu field has a predef
231. psoid xxxxx xx e GPS Datum e Feature name e Labels 1 and 2 as defined in the Data Dictionary When a feature is updated and the GPS position is replaced the GPS Time and GPS Date fields in the EXIF information are updated The EXIF fields for Original Date Time i e when the photo was originally taken are not updated unless the attached photo is replaced 72 TerraSync Software Getting Started Guide User Interface and Data Entry 3 Auto incrementing attributes Any numeric or text attribute can be defined as an auto incrementing attribute When you create a new feature the TerraSync software automatically fills in each auto incrementing attribute with a default value This value is the next value in the auto incrementing sequence is based on the step value you specified in the data dictionary and the last value entered in the field The sequence can increase or decrease and may advance in any increment step value provided this value is within the acceptable range for the attribute Although you can define a text attribute as an auto incrementing attribute only numeric values within the text are incremented or decremented For example if the last value you entered was 47A and the step value is 1 the next value generated by the TerraSync software is 48A However if the last value was AAA the next is still AAA as there is no numeric component to increment When the text consists of more than one number interspersed w
232. r and function See also List buttons page 65 Keyboard shortcuts If you are using a field computer that has a keyboard such as a notebook computer you can use keyboard shortcuts instead of the touch screen To use a keyboard shortcut hold down the ait key on the keyboard and press the letter assigned to the shortcut For example the shortcut letter for switching to the Map section is M so press alt M to switch to the Map section There are two types of shortcuts in the TerraSync software global and local shortcuts Global shortcuts apply wherever you are in the software They let you perform important actions such as switching quickly between the sections of the software If you use the shortcut for the current section or subsection the corresponding list drops down For example if you press Ait M when the Map section is already open the Section list drops down TerraSync Software Getting Started Guide User Interface and Data Entry 3 You can also use global shortcuts to close the current file exit the software or control data logging from any section or screen of the software Note Global shortcuts do not apply when the Data Dictionary Editor is open Local shortcuts apply only within the current form or screen They open lists such as the Options list or subsection list or run commands on the open list The same local shortcut letter may be used in different screens to perform different tasks For example i
233. r lock you can move to the next feature before the required accuracy is reached CAUTION Do not move to another feature before the required accuracy is reached unless you are unlikely to lose lock on the required number of satellites If you lose lock while collecting a series of features you will need to re collect all of the features to obtain features with the required accuracy Provided that the predicted accuracy value passes the threshold of accuracy you require for the features all of the features collected while carrier lock was maintained will achieve the same accuracy after H Star processing TerraSync Software Getting Started Guide 157 6 158 High Accuracy Data Collection Carrier phase postprocessing workflow and required infrastructure This section explains in more detail how to obtain the accuracies specified for carrier phase data collection and postprocessing During GPS data collection where the TerraSync software logs carrier phase data measurements are collected from each individual satellite Carrier phase processing corrects the collected GPS positions using the data from individual satellites so the positions generated during postprocessing are more accurate than positions logged in the field By logging carrier phase data you can achieve accuracies of better than 30 cm after carrier phase processing The following table is a general guide to accuracies that can be obtained with carrier phase data colle
234. r Office project folder If the field computer is a Windows Mobile powered device connect the device to the computer for example using a USB cable or Bluetooth wireless technology Use either Microsoft ActiveSync technology or the Windows Mobile Device Center to manage the connection between the device and the computer The software you use depends on the operating system the office computer is running When the device and the computer are connected one of the following appears on the office computer Ifthe computer is running the Windows 7 or Windows Vista operating system the Windows Mobile Device Center window appears and displays the message Connected For more information refer to the Windows Mobile Device Center Help Ifthe computer is running the Windows XP operating system the Synchronization Setup Wizard appears For more information refer to the ActiveSync Help In the GPS Pathfinder Office software select Data Transfer from the Utilities menu The Data Transfer dialog appears From the Device list select the appropriate device GIS Datalogger on Windows Mobile GIS Datalogger on Windows PC or GIS Folder if the TerraSync and GPS Pathfinder Office software are running on the same computer Alternatively if you have set up a device definition for the field computer select that device name from the list The Data Transfer utility automatically connects to the field computer Select the Send tab Click A
235. r agrees to commence any litigation that may arise under this Agreement in the courts of The Hague The Netherlands 4 3 Reservation of Rights Trimble reserves all rights not expressly granted by this Agreement 4 4 Official Language The official language of this Agreement is English For purposes of interpretation or in the event of a conflict between English and versions of this Agreement in any other language the English language version shall be controlling 5 THIRD PARTY LICENSE RIGHTS 5 1 Portions of this Software incorporating MrSID functionality are provided under license from LizardTech Inc The MrSID software is protected by United States Copyright Law and International Treaty provisions and by U S Patent No 5 710 835 Foreign patents are pending Some of the MrSID technology was developed through a project at the Los Alamos National Laboratory LANL funded by he U S Government managed under contract by the Regents of the University of California University The U S Government and the University have reserved rights in the Technology including the following a the U S Government has a non exclusive non ransferable irrevocable paid up license to practice or have practiced throughout the world for or on behalf of the United States inventions covered by the University s Patent Rights and has other rights under 35 U S C 200 212 and applicable implementing regulations and under the U S Department of Energy DOE
236. r to record offsets 1 ee ees 182 Using an external Sensor es asada a a a ee 182 Repeating features susi ru uii aeaiiai Oe EE a E we eS wee aa DA 183 Segmenting line features wo ee a a ai ee ad a ee ee eS 183 Recording averaged Vertice pocet a e a pae ea ee 184 Enhanced support for adding image files as attributes to features 0 185 Integration with CoPilot Live 7 Professional for Trimble TerraSync and TomTom Navigator 6 turn by turn navigation software 2 ee eee 185 Coordinate Systems 2 0620 ccs bese ted eee eee eee ea nen 187 Modelling the earth s surface 2 eee ee 188 Geoids andellipsoids 1 ee eee 188 Coordinate systems anddatums 0 0 0 c ee eee ee eee 190 Transforming and projecting collected GPS positions 0 00 00 00 eee 191 Transforming real time corrected GPS positions 1 0 eee 191 Coordinate systems available in the TerraSync software 0 00004 eee eee 192 Using the Coordinate System Manager utility 2 2 00 eee eee ee ee 193 Transferring coordinate systems 6 1 ee ees 193 Transferring a coordinate system export file 0 0 0 0 eee eee eee 194 Transferring a single coordinate system 1 0 eee eee ee 195 Configuring coordinate systems 6 ee ee 196 Setting up a Base Station 1 nananaa annann 197 IMtrOdUCHON s o te ke how Soe he en ee ws me ke ete Re ae ae hee oe 198 Logging base data toate ees ey uly ee dds ee ey oe
237. ra Enter a filename Enter a filename manually using the physical keyboard or select the filename from the drop down list for the filename field The drop down list shows files in the current working folder The default location is the My Pictures folder To change the working folder tap the Browse button to the right of the filename field In the pop up window that appears navigate to the folder you need For image files the Browse button a will take you to the thumbnail view for any stored images Tip If you set the working folder to the folder where the files to be attached are stored you can simply select the appropriate file for each feature from the drop down list without having to check or change the working folder each time TerraSync Software Getting Started Guide 71 3 User Interface and Data Entry View a file To view the currently selected file tap the Preview button gt beside the attribute field or tap on the thumbnail for an image file The file is opened in the default program associated with its file type Image files nE TerraSync en E ok Doa eo d eeo Colet Optone Pause m 4 Traffic Sign E OK Cancel a will be displayed full screen in the Pictures amp Videos Date Visited application Type Once you attach a file to a filename attribute in a feature J Image file i and save the feature the selected file is moved to
238. raSync software packaging The Proof of Purchase Number POPN is labelled POPN and is located on the product label affixed to the inside of the software folder e Internet access including a valid email address Note If you do not have Internet access contact your local Trimble reseller for assistance To register your copy of the TerraSync software 1 Goto the My Trimble account login page To do this open your Web browser and go to www trimble com register Alternatively a Insert the TerraSync Software CD in the CD drive of the office computer The Setup screen appears Ss TerraSync Trimble TerraSynce software Version 4 10 Main Menu Install Register Read documentation www trimble com 1995 2009 Trimble Navigation Limited All rights reserved This product is protected by US international copyright trademark and patent laws as described in Status About Note If this screen does not appear select Autorun exe from the CD drive folder b Click Register TerraSync Software Getting Started Guide 19 2 20 Software Installation and Activation Your default Web browser opens and displays the My Trimble account login page Trimble Navigation Central Authentication Service Windows Internet Explorer Ge gt RB hetps login trimble com cas login service http 3a ZF 2Fsup By 2 x File Edit View Favorites Tools Help Google microsoft device controller MDC vista visa
239. re onto a Windows Mobile powered device or to use the more advanced desktop synchronization features with your device you must install Windows Mobile Device Center 6 onto your office computer You can download the Windows Mobile Device Center from www microsoft com windowsmobile devicecenter mspx Installing ActiveSync technology ActiveSync technology may be supplied on a CD with the Windows Mobile powered device or you can download it from www microsoft com windowsmobile Tip If you are installing a translation of the TerraSync software and you want all installation screens to appear in the translated language install the corresponding translation of the ActiveSync technology You can download translated versions of the ActiveSync technology from the Microsoft website TerraSync Software Getting Started Guide 27 2 Software Installation and Activation Step 2 Connect the device to a computer 1 Make sure that the device and the computer are turned on 2 Connect the device to the office computer using either a USB cable connection or Bluetooth wireless technology For more information on connecting the device to a computer refer to the documentation for the Windows Mobile powered device When the device is connected a window appears on the office computer that enables you to manage the connection 3 If the office computer is running e the Windows Vista or Windows 7 operating system If the Autoplay window appears close
240. rea and does not provide for variations that occur in local coordinates When you create a site you shift coordinates obtained using GPS so that they better fit coordinates in the existing map grid that were obtained using traditional surveying methods TerraSync Software Getting Started Guide 219 Glossary SNR SSF static GPS position static mode streaming GPS position synchronize tracking true north UTC UTM vector velocity vertex See signal to noise ratio Standard Storage Format A Trimble file format SSF files store GPS data from a Trimble GPS receiver Usually these files have the filename extension ssf A corrected SSF file has a cor or phs extension an SSF file created by importing data has the extension imp A static GPS position is a GPS position logged when the GPS receiver is stationary as when logging a point feature or an averaged vertex in a line or area feature During RTK data collection TerraSync logs point features and vertices in static mode Line features area features and between feature positions are logged in roving mode In static mode the TerraSync software records only the RTK corrected position with the best precision All other positions are discarded Also known as dynamic GPS positions Streaming GPS positions are GPS positions logged when the GPS receiver is moving When you are moving along a line feature or around the perimeter of a polygon feature you lo
241. rier phase postprocessing provides a cost effective solution for achieving accuracies ranging from 30 cm down to 1 cm requiring carrier data spanning from 10 minutes up to 45 minutes Pros The highest level of postprocessed GPS accuracy Moderately priced field equipment Potential to leverage public base station infrastructure and thereby avoid any direct infrastructure cost Areas where public base station infrastructure does not exist will require infrastructure investment to achieve centimeter level accuracy Operational constraints such as limited distance from a base station and precisely surveyed base station infrastructure TerraSync Software Getting Started Guide 149 6 150 High Accuracy Data Collection The requirement for long continuous carrier data durations makes traditional carrier postprocessing impractical in tough GPS environments where satellite signals are interrupted for example in high multipath environments or under tree canopy Positions are not usable until the minimum carrier lock time has elapsed Inability to achieve this level of accuracy in real time making precise relocation applications impossible Accuracy degrades quite rapidly with increasing distance between the base and roving GPS receivers Real time kinematic RTK Survey receivers with real time kinematic capability achieve centimeter level accuracy in real time with no need for subsequent postprocessing Pros The high
242. rotect the field computer by connecting either the null modem adaptor P N 43197 or the curly straight through cable P N 45052 to the receiver cable These two connectors do not supply power so they will protect the field computer from power output by the receiver TerraSync Software Getting Started Guide Software Installation and Activation 2 Ifa powered connection is acceptable or necessary you can connect directly to the receiver or you can use the curly straight through cable P N 30236 instead of cable P N 45052 If you are unsure whether a powered connection will cause damage refer to the user manual for the field computer or consult the manufacturer before using P N 30236 Connecting to external real time correction devices To connect to a GPS receiver and an external real time correction device such as a Trimble GeoBeacon receiver use one of the following options e Ifyou are using a serial cable connection to both receivers use a splitter cable e Ifthe field computer has two Bluetooth ports you can connect to both the GPS receiver and the real time correction device using Bluetooth connections e Ifthe field computer has only one Bluetooth port use Bluetooth wireless technology to connect the real time correction device to the GPS receiver and then use Bluetooth wireless technology to connect the GPS receiver to the field computer Alternatively you can use a combination of Bluetooth wireless technology and cabl
243. rrection source You will then use the Seaview data dictionary to verify and update the attributes for those features This part of the tutorial gives step by step instructions to follow before you go into the field to update data See e Creating a data dictionary from existing data files page 128 Importing data from a GIS into the GPS Pathfinder Office software page 130 e Transferring data to the field computer page 133 amp Creating a data dictionary from existing data files Note This step is necessary only for the tutorial Normally before collecting any data you would create a data dictionary on a desktop computer and then use the Data Transfer utility to copy the data dictionary to the field computer Alternatively you would create a data dictionary in the TerraSync software Before you can import data from a GIS you need to recreate the Seaview data dictionary on the desktop computer Each SSF file contains a copy of its associated data dictionary You will use the Starfish data file to recreate the Seaview data dictionary that is on the field computer To create a data dictionary from a data file 1 Start the GPS Pathfinder Office software and then open the TerraSync Tutorial project 2 Start the Data Dictionary Editor utility In the GPS Pathfinder Office software select Data Dictionary Editor from the Utilities menu The main Data Dictionary Editor window appears Select File Import From Data File The Imp
244. rs The selected time zone of the field computer is incorrect Before you open any data files use the World Clock utility on the field computer to set the local time zone correctly For more information refer to the documentation for the field computer 208 TerraSync Software Getting Started Guide Position accuracy This section lists possible causes of and solutions to problems with the accuracy of GPS positions Troubleshooting D Problem Possible cause Solution The accuracy of recorded GPS positions is not as good as expected You did not record sufficient positions to achieve the required accuracy In the Data Dictionary Editor increase the value in the Minimum Positions field to make sure that the TerraSync software records enough positions Collect more positions at each point feature The maximum DOP value was too high If you record positions when the DOP is high this has a detrimental effect on the accuracy of these positions In the GPS Settings form see page 88 lower the maximum PDOP or HDOP value to make sure that the TerraSync software only logs accurate positions The accuracy of recorded GPS positions is not as good as expected You are operating in an area of high multipath Move to an area with better GPS coverage and use offsets Apply velocity filtering e Set the Velocity Filter field on the GPS Settings form to Auto to apply velocity
245. ruction and move away from it Note GPS does not work indoors The GPS receiver s external antenna or antenna cable has not been connected has been connected incorrectly or is faulty Check that the external antenna is connected correctly If the receiver still fails to acquire signals from a satellite then the antenna and or antenna cable may require servicing The receiver has not been used for a very long time and the almanac stored in the receiver is outdated Wait for up to 15 minutes until a new almanac has been recorded Subsequent restarts should then be rapid The receiver has been set to Base mode by another application Reset the GPS receiver To do this open the Setup Section see page 88 tap Options and then select Reset GPS receiver The receiver is not able to compute a GPS position within one minute of starting the TerraSync software There are not enough satellites available Four SVs are required to compute a position Use mission planning to check that there are sufficient satellites visible at this time In the GPS Settings form see page 88 check that the minimum elevation value is not too high In the GPS Settings form see page 88 check that the minimum SNR value is not too high The current DOP value is too high Use mission planning to check for times when the PDOP or HDOP value will be below the configured maximum value In the GPS Settings
246. s The following topics describe the different types of displays e Screens page 62 e Graphical screens page 63 e Forms page 63 The TerraSync software screens also have the following features e Lists page 64 e Buttons page 65 e Data entry fields page 69 e Auto incrementing attributes page 73 e Pop up messages page 73 e Sound page 75 e Color page 77 For more ways to interact with the software if the field computer has a keyboard see Keyboard shortcuts page 66 Screens Use screens to view information in a list or table or to make selections that provide access to other areas in the software A screen usually displays information that you cannot edit directly Choose Existing Data File Location De gt Most screens contain buttons lists or labels When a screen contains a field a default value is supplied in the field Examples of screens are e The top level screen for each subsection in the Data section such as the New File screen andthe Features 196 Positions 460 Status Not Transferred DD Sample File Manager screen e The main screen of the Setup section 62 TerraSync Software Getting Started Guide User Interface and Data Entry 3 Graphical screens Use graphical screens to view information graphically You cannot enter data in a graphical screen and you cannot edit the information displayed Examples of graphical screens are e The Skyplot screen a
247. s 73 delaying logging 102 delaying logging overview 174 deleting wav files 76 deletion status filtering by 139 desktop PC see PC Device Lock utility 55 DGPS definition 219 generating corrections 198 dialling rules 166 Dialup Networking DUN service 165 differential correction definition 213 differential GPS definition 219 digitizing definition 213 icon 59 tooltip 61 Dilution of Precision definition 213 direct dial connection to VRS network 170 172 Direction Dial screen 140 distance distance offsets overview 180 DOP definition 213 Index easting converting 190 EGNOS definition 213 ellipsoid definition 213 local 189 216 overview 188 189 equipment checking 93 error messages 74 existing file opening 138 exiting the TerraSync software 56 Export utility 126 exporting datatoaGIS 126 external correction source troubleshooting 205 external RTK icon 58 tooltip 60 external sensor 182 F feature types filtering by tutorial 139 features definition 213 features attaching files to 71 filtering 139 logging immediately 174 logging later 174 offsets 176 segmenting 109 183 field computer battery level 58 definition 213 specifications 18 troubleshooting 203 fields moving between 63 filename attributes fillingin 71 files attaching to features 71 filter icon 58 tooltip 61 filtered features 139 filtering 139 filtering setting criteria tutorial 139 Folder Search dialog 123 forms data entry 69 mo
248. s a default name in the File Name field Replace the default name with Starfish In the Dictionary Name field make sure that the Seaview data dictionary is selected Tap Create The Confirm Antenna Height form appears If necessary enter the correct antenna height and measurement point and then tap OK The Collect Features screen appears This screen shows a list of all the features in the data dictionary You have now created a new data file and can start collecting features TerraSync Software Getting Started Guide Create New Data File File Type Location File Name Rover Default v sta rfish Dictionary Name Seaview X File Starfish Choose Feature Create Type a m Traffic Sign Garbage Can x Light Pole x Tree we Road wo Path we Fence a Park g amp o Sand Box Sa Waterbody v Tutorial Collecting Data 5 Collecting a point feature with Log Now The first new feature you need to record is a traffic sign This is a point feature To record a point feature remain stationary while the TerraSync software logs GPS positions These GPS positions are averaged to compute the final feature position of the point feature When the TerraSync software is logging GPS positions the logging icon appears in the status bar The number beside the icon indicates how many positions have been logged for the selected feature
249. s an internal non volatile location Before you install the TerraSync software make sure that you have enough free space on the device The TerraSync software requires at least 18 MB of free space If you are installing it to a secondary internal storage location such as the GeoExplorer 2003 series handheld s Disk the TerraSync software requires at least 18 MB of free space in that location plus 5 MB of RAM Note The installation program cannot determine how much memory is available in the non volatile storage location You must ensure that 18 MB is free before you begin the installation If there is not enough memory space on the device a message appears during installation indicating the amount of memory left on the device TerraSync Software Getting Started Guide Software Installation and Activation 2 Click Cancel remove any unwanted programs or data files from the device and or increase storage memory Then start the installation again Ifmemory space in the secondary internal storage location is insufficient the installation may appear to complete successfully but error messages may appear when you try to run the TerraSync software If this happens make more space available in the secondary storage location and then install the software again Step 6 Install the TerraSync software onto the device 1 Before you begin make sure that you have registered your copy of the software and have made a note of the install
250. scale where all features are visible The features have been filtered out The features have been deleted Open the Filter By form where you can disable or change the criteria for filters see page 84 Deleted features are never shown in the Map section In the Update Features screen see page 84 select a deleted feature a feature with a line through it tap Options and then select Undelete TerraSync Software Getting Started Guide 207 D Troubleshooting Coordinate system This section lists problems you may encounter with the coordinate system Problem Possible cause Solution The coordinates displayed by the TerraSync software seem to be incorrect You have selected the wrong coordinate system or zone In the Coordinate System form select the correct coordinate system and zone see page 88 You have selected the wrong coordinate units In the Coordinate System form select the coordinate system then select the correct coordinate units see page 88 You are using the Latitude Longitude coordinate system and have selected the wrong datum In the System field on the Coordinate System form see page 88 select Latitude Longitude and specify the correct datum You are using the UTM coordinate system and have selected the wrong UTM zone or datum In the System field on the Coordinate System form see page 88 select UTM then specify the correct zone and datu
251. setting or menu item is locked by the current configuration A locked icon i appears beside locked settings and menu items You have forgotten the password for the configuration file Unlock the configuration file Use the manager s password TrimbleTerraSync Automatically generated time attributes are incorrect The internal clock on the field computer has been set incorrectly or the selected time zone is incorrect Before you open any data files use the World Clock utility on the field computer to set the local time and time zone correctly For more information refer to the documentation for the field computer File dates are incorrect 206 The internal clock on the field computer has been set incorrectly or the selected time zone is incorrect TerraSync Software Getting Started Guide Before you open any data files use the World Clock utility on the field computer to set the local time and time zone correctly For more information refer to the documentation for the field computer Map screen This section lists problems you may encounter with map files Troubleshooting D Problem Possible cause Solution Some or all features are missing from the Update Features screen or the Map section Some or all features are missing from the Update Features screen or the Map section There is no data file open Use the New File form to create a new file see page
252. sitions and known truth points do not coincide You have incorrectly configured the real time correction source datum In the Real time Settings form see page 168 check that the datum for the real time source you are using is correctly selected TerraSync Software Getting Started Guide 209 D Troubleshooting 210 TerraSync Software Getting Started Guide Glossary This section explains some of the terms used in this manual almanac attribute attribute value base station baud rate bearing broadcast server C A code carrier phase Cartesian coordinates centroid An almanac is data transmitted by a GPS satellite which includes orbit information on all the satellites clock corrections and atmospheric delay parameters The almanac is stored on the field computer It is used to facilitate rapid acquisition of GPS signals when you turn on the TerraSync software or when you have lost track of satellites and are trying to regain GPS signals An attribute is information about a geographic feature in a GIS or database usually stored in a table and linked to the feature by a unique identifier Every identifiable feature has attributes One common attribute of all mapped features is geographic position Other attributes depend on the type of feature For example attributes of a road might include its name surface type and number of lanes Each attribute has a range of possible values called a do
253. stem and test it to make sure that everything is connected correctly e make sure that the receiver and field computer batteries are charged e make sure that the field computer and GPS receiver are communicating correctly CAUTION After testing the system turn off the field computer and any other equipment such as radios before proceeding to the start point of your field work Leaving equipment on wastes battery life especially if it will be some time before you need to use the equipment Tip When you turn off the field computer any receiver that is connected to it is automatically turned off TerraSync Software Getting Started Guide 93 5 94 Tutorial Collecting Data Exercise 2 Data collection This part of the tutorial uses the Seaview data dictionary that is already installed on your field computer You are ready to go to Starfish Bay and collect features But first there are some tasks that you should complete This section explains the tasks and gives the step by step instructions required to collect point line and area features with a variety of different attributes See e Initial tasks page 94 e Collecting new data page 100 To complete this part of the tutorial you must be outside in a place where you can get good GPS signals Note Some TerraSync screens may appear different from the screens shown in this tutorial D Initial tasks Before starting a data collection session you need to perform
254. t unusable carrier phase data lock is regained 5 or more satellites useful carrier phase data lock is again lost unusable carrier phase data Figure 6 1 Blocks of carrier phase data for static GPS observations relative to satellite lock As soon as four or more satellites are available a new block begins This block continues until lock is lost After postprocessing all the data in a given block has the same level of accuracy The accuracy achieved depends on the duration of each carrier block 152 _ TerraSync Software Getting Started Guide High Accuracy Data Collection 6 The relationship between time and accuracy With all three carrier phase techniques accuracy improves with the duration of carrier lock longer baseline short baseline gt Figure 6 2 Accuracy achieved relative to time elapsed assuming that carrier lock is maintained Figure 6 2 shows that the error decreases quickly at first and then more slowly as time progresses This is true for both the real time and postprocessed carrier phase techniques Tip To automatically log data until a pre specified accuracy level is met use the accuracy based logging capability provided by the TerraSync software For example you can specify that all positions must have a horizontal accuracy of 10 cm or less If the GPS receiver calculates a position that does not meet this accuracy requirement TerraSync does not log that position Note
255. t Option Combine and output to Export folder GIS Coordinate System Site System Lat Long Zone Datum WGS 1984 Coordinate Units New Delete Properties If the file Starfish cor does not appear in the Selected Files field click Browse to open the Open dialog Browse for Starfish cor select it and then click Open Select the output folder By default this is the export folder in the current project In the Choose an Export Setup group select Sample ESRI Shapefile Setup Make sure that the GIS Coordinate System group shows the Latitude Longitude coordinate system Ifthe coordinate system is incorrect click Properties and then select the Coordinate System tab in the Export Properties dialog to change the coordinate system To export a prj projection file with your files click Browse next to the Projection Files field and then navigate to the location of the prj file and select it If you do not want to export a prj file or if you cannot locate a file then skip this step Click OK to close the Export Properties dialog Click OK to export the selected file s using the specified export setup TerraSync Software Getting Started Guide Tutorial Collecting Data 5 9 The Export Completed dialog details the results of the export Click Close to close this dialog The file is now in the format required for you to open it in your GIS Tip Use the Batch Processor utility to increases productivit
256. t as a guest you can e move or copy files between the two computers e back up files on the Windows Mobile powered device e install or uninstall programs on the Windows Mobile powered device However you cannot synchronize data between the two computers when you connect as a guest To synchronize data you must set up a partnership A guest connection is temporary When the guest Windows Mobile powered device is disconnected from the desktop computer any settings for the guest connection are lost The next time you connect the device to the desktop computer you must set the guest connection again For more information refer to the ActiveSync Help See Height Above Ellipsoid See Horizontal Dilution of Precision The heading is the direction you are facing or traveling usually measured clockwise from north HAE HAE is a method for referencing altitude Altitudes expressed in HAE are actually giving the height above the datum not the ellipsoid GPS uses the WGS 84 datum and all heights are collected in relation to this surface It is important to use the same datum when comparing altitudes in HAE The line at which the earth and sky seem to meet 214 TerraSync Software Getting Started Guide Horizontal Dilution of Precision H Star technology IMS International Terrestrial Reference Frame Internet Map Server ionospheric noise ITRF L1 L2 laser rangefinder Glossary HDOP Dilution of Precision D
257. t button and then select Map The features that you have collected are displayed on the map along with the park perimeter that you are currently collecting TerraSync Software Getting Started Guide 103 5 Tutorial Collecting Data 8 Ifyou cannot see your current position on the map tap Options and then select Auto Pan to GPS Position ete7e0060 0 Line feature Current area feature Point feature To view the map at different scales tap the Zoom In or Zoom Out button on the Command bar Alternatively tap the Map Tools list button select Zoom In or Zoom Out and then select the point on the map that you want to zoom in to or out from Note Your Map screen may appear different from the one shown 9 10 11 12 13 Tap the Section list button and then select Data to go back to the Data section The Park attribute entry form is still active and the TerraSync software is still logging positions for the park Enter the attributes of the park In the Name field enter Starfish Park and then select Yes from the Restrooms field When you have travelled around the perimeter of the area tap OK to save the feature and return to the Collect Features screen Tap Close in the Collect Features screen When prompted to confirm closing the file tap Yes to close the current data file and return to the New File screen You have finished collecting features for this exercise Now you will add a waypoi
258. t were an averaged vertex If you log a number of positions at each reference point the TerraSync software averages these positions to give a more accurate reference position The principle of Dilution of Precision applies to complex offsets so you should choose reference positions that are widely spaced TerraSync Software Getting Started Guide Advanced Datalogging Options A For detailed instructions see Recording a complex offset page 179 Recording a complex offset To record a complex point offset 1 Start the point feature 2 From the attribute entry form tap Options select Offset and then from the pullout menu select the type of offset you want to record The appropriate offset form appears 3 Follow the instructions at the top of the form When you have completed each step tap Next to move to the next step For each reference position Move to the reference position a b Tap Log or Resume to begin logging TerraSync Par de x 53 eo 0 om option gt Triple Distance offset for 9 Tree Enter the distance from reference ition 1 to the fee Puen ae Next Clear Reference position 1 Collected Collect Distance A Horizontal distance 13 00 m 0 00 m Vertical distance c Remain stationary at the reference position while you log positions When you have collected sufficient positions e Measure the offset This is the distance or the
259. tall the TerraSync software onto an office computer such as a laptop or a Tablet PC that is running a Windows operating system The installation procedure comprises the following steps 1 Back up any TerraSync software data files 2 Uninstall any previously installed versions of the TerraSync software 3 Install version 4 10 of the TerraSync software More information about each step is provided below Step 1 Back up any TerraSync software data files Before installing a new version of the TerraSync software Trimble recommends that you transfer any TerraSync software data files to a safe storage location TerraSync Software Getting Started Guide 43 2 Software Installation and Activation Step 2 Uninstall any previous versions of TerraSync software Before installing a new version of the TerraSync software Trimble recommends that you uninstall any previously installed versions of the TerraSync software Step 3 Install the TerraSync software onto the computer 1 Before you begin make sure that you have registered your copy of the software and have made a note of the installation code that you must enter during installation For more information see Registering the TerraSync software page 19 the TerraSync software is not running on the computer you have closed all open windows programs on the PC 2 Insert the TerraSync Software CD into the CD drive of the office computer Alternatively if you are entitled to an up
260. th When you segment a line feature the TerraSync software immediately records a position even if the logging interval does not require a position at that time This position becomes the last position in the old line and the first position in the new line Recording a position at the segmentation point ensures that the two line segments join up in the Trimble postprocessing software and the GIS The offset of the new line segment defaults to the offset of the previous line segment if there is one The new line feature has the same attribute values as the previous line segment except that any auto incrementing attributes are incremented to the next value Note If the line feature has an offset the two line segments may not snap together TerraSync Software Getting Started Guide 183 A Advanced Datalogging Options A A To segment a line feature see Collecting a line feature with differing attributes line segmentation page 109 CAUTION If you are logging an averaged vertex when you segment a line feature the first position of the new segment is located at the last GPS position not at the calculated position of the last averaged vertex This can cause a gap between the segments To ensure that the two segments join record a single unaveraged GPS position as the last position in the first segment Then segment the feature and start recording averaged vertices for the new segment if required CAUTION If logging has
261. th s surface m Transforming and projecting collected GPS positions m Coordinate systems available in the TerraSync software m Using the Coordinate System Manager utility m Transferring coordinate systems Configuring coordinate systems It is useful to have some understanding of coordinate systems and datums before collecting GPS data The GPS receiver computes positions in terms of the WGS 84 coordinate system and stores them as latitude longitude and height above ellipsoid LLH values However you may want to work with positions in terms of a different coordinate system The TerraSync software transforms GPS positions from the WGS 84 coordinate system to the selected coordinate system This lets you enter and display coordinates using the coordinate system that best suits you and the location you are working in Note The TerraSync software records all positions internally in terms of the WGS 84 coordinate system This makes it possible to use different coordinate systems and datums without compromising the data To allow for seamless data transfer when correcting data in real time it is imperative that the real time correction source reference system is correctly identified before use and selected during use See Transforming real time corrected GPS positions page 191 TerraSync Software Getting Started Guide 187 B Coordinate Systems 188 Modelling the earth s surface Because it is difficult to repres
262. the TerraSync software data folder and assigned a unique name If you open the feature for review later the actual filename is not displayed because the file has been renamed Instead a message similar to Attached JPG File appears in the attribute field e When you transfer the data file to the office computer using the Trimble Data Transfer utility any attached files are transferred with the data file and are stored with the transferred data file This link is also maintained when you export the data file to a GIS For more information refer to the Data Transfer Utility Help Tip Sometimes to save space or to create better quality files recording software on a Windows Mobile powered device such as sound recording software that creates wav files uses a default file format that is unreadable on a desktop computer Before going out into the field test that you can transfer and read files created by the software that you want to use If necessary change the settings of the recording software to use a format that is compatible with the desktop computer EXIF Exchangeable image file format support When a jpg image file is attached to a feature in TerraSync and there is a current GPS position the EXIF header of the image file is populated with the following fields e GPS Time UTC e GPS Date YYYY MM DD e GPS Longitude DD_MM_SS SS e GPS Latitude DD_MM_SS SS e GPS Altitude Height Above Elli
263. the Name attribute 8 Tap OK to save the feature and return to the Collect Features screen 108 TerraSync Software Getting Started Guide Tutorial Collecting Data 5 a Collecting a line feature with differing attributes line segmentation You need to collect a new street feature for a street that has two surfaces The first half of the street surface is concrete and the second half of the street surface is asphalt To do this you will record the feature and then segment the feature into two segments joined together Each segment has a different value for the Surface Type attribute Concrete Asphalt Oyster Lane To segment a line feature 1 Make sure Log Later is selected To do this tap Options and then select Log Later In the Collect Features screen select the Road feature and then tap Create Walk to the beginning of Oyster Lane In the Name field enter Oyster Lane From the Surface Type field select Concrete Tap Log Nn a FF WY SN Start walking along the concrete segment of Oyster Lane TerraSync Software Getting Started Guide 109 5 Tutorial Collecting Data 8 Just before you reach the asphalt segment tap Options and then select Segment Line where the asphalt segment begins The TerraSync software ends the current line feature and immediately starts another line feature of the same attribute X Tip There is no need to stop walking when segmenting a line However if you need to stop tap
264. the feature is updated or both TerraSync Software Getting Started Guide User Interface and Data Entry 3 Date Enter a date value manually using the physical CAKES S A ok keyboard or select it from the drop down calendar Options To enter a date manually type it in from the keyboard To select it from the calendar tap the drop down arrow NallieSian a at the right of the date field and select the date required s e Type from the calendar MT WTF S 12 3 45 67 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 26 27 28 J 30 31 Condition In the data dictionary you can specify that a date attribute is automatically set to the current date when the feature is created when the feature is updated or Image file both Today 10 29 09 Filename A filename field is primarily used for attaching image files but this can also be used to attach other files to a feature If your field computer does not have an integrated camera use a digital camera to create and save images When the TerraSync software is running on a Trimble device which is powered by the Windows Mobile 5 0 or 6 operating system and which has an integrated camera you can switch to the camera live preview window Tap on the Camera icon next to the Filename field to switch to Camera mode Note Note the Camera button is only displayed if the handheld device has an integrated came
265. the screen to close the My ISP screen 7 Tap OK in the top right corner to close the Connections screen 8 Tap EJ in the top right corner to close the Settings screen TerraSync Software Getting Started Guide 167 6 High Accuracy Data Collection To check the connection status at any time tap the Aj or RA icon in the title bar To end the connection at any time tap the fj or PJ icon in the title bar and then tap Disconnect Step 4 Configuring the TerraSync software to use real time corrections from the Internet source 1 On the field computer start the TerraSync software and then open the Setup section 2 Tap Real time Settings The Real time Settings form appears 3 From the Choice J field select External Source 4 Configure the external source a Tap the Setup button H beside the Choice 1 _ field The External Source Settings form Astle Mo appears a External Source Settings OK Cancel Correction Datum WGS 1984 hd b From the Correction Datum field select the same datum as the VRS network coordinate system c From the Type field select Type VRS 7 Connection Method Internet v VRS ifthe real time correction sourceisa gares VRS network 10 3 16 63 Single Base if the real time correction Port Eo a source is a single base station that broadcasts its corrections over the Internet d From the Connection Method field select Internet
266. the window b The Windows Mobile Device Center window displays the message Connected Connect without setting up your device c Click Connect without setting up your device d Use the Windows Mobile Device Center to back up data files and uninstall any previous versions of the software see Step 3 page 30 and Step 4 page 30 For more information refer to the Windows Mobile Device Center Help 28 TerraSync Software Getting Started Guide Software Installation and Activation the Windows XP operating system a If the Synchronization Setup Wizard appears click Cancel to close the wizard Synchronization Setup Wizard Welcome to the Pocket PC Sync Setup Wizard To set up a sync relationship between this computer and your Pocket PC click Next ff you click Cancel you can still e Copy and move files between your Pocket PC and this computer Add and remove programs on your Pocket PC Guest Connected 2 Use ActiveSync technology to back up data files and uninstall any previous versions of the software see Step 3 and Step 4 below For more information refer to the ActiveSync Help TerraSync Software Getting Started Guide 29 2 30 Software Installation and Activation Step 3 Back up any TerraSync software data files Before installing a new version of the TerraSync software Trimble recommends that you transfer any existing TerraSync software data files to
267. their attributes or edit them Velocity is essentially a measure of speed that takes into account direction of travel as well as the distance traveled over a period of time A point on a line or area feature where two adjacent segments of the feature join Each position that you collect for a line or area feature is a vertex of that feature 220 TerraSync Software Getting Started Guide VRS network WAAS waypoint Web map server WGS 84 Windows Mobile powered device Glossary A VRS network consists of GPS hardware software and communication links It uses data from several base stations to provide corrections to roving receivers that are more accurate than corrections from a single base station Unlike other real time correction sources using corrections from a VRS network requires two way communication between the VRS network and the roving receiver The roving receiver must send its position to the server so that the server can calculate corrections for that position and select the closest base station if necessary The server generates a unique virtual reference station for each roving receiver that connects to it Wide Area Augmentation System WAAS is a satellite based augmentation system SBAS that provides a free to air differential correction service for GPS WAAS was established by the Federal Aviation Administration FAA Its coverage area includes the continental United States and outlying parts of Canada a
268. ther a cable or Bluetooth wireless technology to connect the receiver to the field computer running the TerraSync software b Inthe TerraSync software select Setup from the Section list and then tap GPS Settings c From the GPS Receiver Port drop down list select the COM port that the receiver is connected to and then tap OK d From the Setup section tap GPS to connect the TerraSync software to the receiver The Skyplot screen shows the status of the connected GPS receiver Note GPS positions may not always be available particularly in or near buildings in vehicles or under tree canopy Q Checking the GPS status Use the satellite icon on the status bar to check if the receiver is computing GPS positions This icon provides information about the geometry of the satellites that are being used to compute GPS positions Use the Status section to view the satellites currently tracked and those that are being used to calculate the current position To view the GPS status 1 The Skyplot screen appears when you first run the TerraSync software If this screen is not visible tap the Section list button and then select Status Then tap the Subsection list button and select Skyplot 2 Use the Skyplot to see which satellites are being tracked and to see your current position TerraSync Software Getting Started Guide 95 5 96 Tutorial Collecting Data mo TerraSync Satell
269. tion time To initialize in static mode remain stationary and hold the GPS antenna still The Estimated Accuracy icon in the status bar of the TerraSync software shows the estimated accuracy for the current GPS position Use the accuracy based logging capability provided by the TerraSync software to reject any positions that do not fall within the specified required accuracy TerraSync Software Getting Started Guide High Accuracy Data Collection 6 Using corrections from a VRS network A virtual reference station network consists of GPS hardware software and communication links It uses data from a network of base stations to provide roving receivers with corrections that are more accurate than corrections from a single base station gP Base station Base station GPS observables GPS observables Roving receiver Real time corrections ae observables Base station Server Figure 6 3 Parts of a VRS network The server is a computer running VRS software such as the Trimble GPSNet software The server uses the base station data to model systematic ephemeris tropospheric and ionospheric errors at the roving receiver s position It then sends interpolated correction messages back to the roving receiver Depending on the VRS software the server may also use the data from the base station network to simulate a base station or virtual reference station at the location of the roving receiver If no network
270. to a waypoint see page 145 e Collecting the target as a point feature see page 146 e Ending the data collection session see page 146 D Changing the accuracy based logging settings Because you are using real time differential corrections in the field you want to use an estimated accuracy that is calculated in the field rather than after postprocessing This means that when the TerraSync software calculates the horizontal estimated accuracy of each GPS position the calculation includes the corrections from the real time correction source that are applied during data collection 1 Tap the Section list button and then select Setup 2 Tap Logging Settings TerraSync Software Getting Started Guide 137 5 138 Tutorial Collecting Data Tap Setup below the Accuracy Settings field The Accuracy Settings form appears From the Accuracy Value for Display Logging fields select Horizontal for the accuracy of the current GPS position and then select In the field to use the real time corrected accuracy From the Use Accuracy based Logging field select Yes From Apply Accuracy based Logging To field select All Features From the Required Accuracy field select 5 m mo lerraSync Setup Accuracy Settings OK Cancel Accuracy Value For Display Logging Horizontal y In the field Use Accuracy based Logging Yes Apply Accuracy based Logging To All
271. ts and screens for navigation Use the screens in the Navigation section with the Map section to navigate to specific locations You can use real time differential GPS to optimize navigation and provide differential accuracy when in the field Use the Turn by turn settings to work with turn by turn navigation software When CoPilot Live 7 Professional for Trimble TerraSync software or TomTom Navigator 6 turn by turn navigation software is installed on the device the TerraSync software automatically switches to the navigation software to navigate to the selected target then switches back when you have arrived at the destination Status The Status section contains information screens Use the Status section to view summary or detailed information about the software the GPS receiver any real time source you have configured and the location and health of the satellites the receiver is tracking Setup The Setup section provides forms for configuring the TerraSync software Use the Setup section to control how the TerraSync software interacts with the GPS receiver and with any real time correction sources you have configured and to configure data collection and display settings If you use the TerraSync software on a desktop or laptop computer the screen is arranged in panes Each pane displays a section of the software Depending on the screen resolution up to three panes can be displayed By default when the TerraSync software op
272. ttings dwalton My Documents G Select m Reference Position Use reference position from base files Use reference position from base provider Land Information NZ Taylor Lake IV Confirm base data and position before processing lt Back Cancel Help 122 TerraSync Software Getting Started Guide 10 11 Tutorial Collecting Data 5 There are three options for locating base data download files from a base provider using the Internet use base files that you have previously downloaded and saved in the base data folder for the project browse for base files that you have previously downloaded and saved elsewhere Do one of the following Ifyou have access to the Internet download base data files from a base provider a b C In the Base Data group select Base Provider Search Click the Select button next to the Base Provider Search text box The Select Base Provider dialog appears The dialog displays a list of available base providers The list is arranged by distance from the location where the field data was collected so that base stations closest to the location where the data was collected are at the top of the list Click a base provider to select it and then click OK Ifyou do not have access to the Internet use base data files that have been downloaded to a folder a C d In the Base Data group of the Select Base Data page of the wizard select Folder Sear
273. ttings screen make sure that Dialup Networking DUN is selected and then tap Finish on the right softkey You have now created a partnership between the field computer and the phone so that they can communicate From the My Connections list select the phone that you want to configure the connection to and then if required tap Next on the right softkey Enter the GPRS access number for the Internet Two of the common GPRS access numbers for cellular phones on GSM networks are 99 1 and 99 If these access numbers do not work contact the cellular phone provider to obtain the appropriate number to use Note You do not need to set up dialling rules or change the Internet connection settings on the phone The connection settings you enter on the field computer are passed to the phone to use for this connection 166 TerraSync Software Getting Started Guide 10 High Accuracy Data Collection 6 Tap Next on the right softkey Unless the phone provider confirmed that you must enter user name password and domain settings to access the Internet tap Finish on the right softkey without entering any information in this screen Otherwise a Enter the required information b Ifthe phone provider has told you that you need to change the baud rate or other settings for the connection tap Advanced configure these settings and then tap OK in the top right corner of the screen c Tap Finish on the right softkey You are returne
274. u can give all projects meaningful names and assign separate folders for base export and backup files You can also set up projects for different groups of data For example you could create a project for each subdivision in the city or for each month For this tutorial you need to create a new project called TerraSync Tutorial To create a project in the GPS Pathfinder Office software 1 Start the GPS Pathfinder Office software To do this from the Windows Start menu select All Programs Trimble GPS Pathfinder Office GPS Pathfinder Office The main window of the GPS Pathfinder Office application appears 2 By default the Select Project dialog appears If it does not appear select File Projects 3 Click New The Project Folders dialog appears Project Folders a Project Name B Comment Thursday February 28 2008 9 31 19am Project Folder CAUsersWDoe Documents GP5 Projects Browse Backup Folder Backup Browse Export Folder Export Browse Base File Folder Base Browse Cancel Default Help 4 Inthe Project Name field enter TerraSync Tutorial and then press the Tab key TerraSync Software Getting Started Guide Tutorial Collecting Data 5 The Project Folder field is updated to show the default folder for the new project Note By default all GPS Pathfinder Office software projects are stored in the GPS Projects folder The default location of the GPS Projects folder depends on t
275. u collected the features so you need to update their attributes Before going back to Starfish Bay you import data from the Seaview Authority GIS into the GPS Pathfinder Office software transfer it to your field computer and prepare for data update Finally you return to the field and navigate to existing features to update their attributes You use the TerraSync software and a real time differential GPS source to navigate back to features and update their attributes The data update part of the tutorial begins on page 135 TerraSync Software Getting Started Guide 91 5 92 Tutorial Collecting Data amp Exercise 1 Preparing for data collection Before going to Starfish Bay to collect data you need to create a new project in the GPS Pathfinder Office software Then you need to check your equipment to make sure that you are ready to go out into the field This section provides step by step instructions that will prepare you for data collection See e Creating a project page 92 e The Seaview data dictionary page 93 e Checking the equipment page 93 Creating a project The GPS Pathfinder Office software provides a set of tools for processing and managing GPS and GIS data The GPS Pathfinder Office software lets you plan your data collection session easily and process the GPS data successfully Use the GPS Pathfinder Office software to organize work into projects Dividing the work in this way helps you manage your files Yo
276. uide real time differential GPS real time kinematic rover roving mode RTCM correction messages RTK SBAS signal to noise ratio site Glossary also known as real time differential correction DGPS Real time differential GPS is the process of correcting GPS data as you collect it This is achieved by having corrections calculated at a base station sent to the receiver via a radio link As the rover receives the position it applies the corrections to give you a very accurate position in the field Most real time differential correction methods apply corrections to code phase positions RTK uses carrier phase measurements See RTK A rover is any mobile GPS datalogger collecting or updating data in the field typically at an unknown location Data collected on a rover can be differentially corrected relative to base station data During RTK data collection TerraSync logs line and area features and between feature positions in roving mode Point features and vertices are logged in static mode In roving mode the TerraSync software records all RTK corrected positions that meet the precision tolerances you have specified All other positions are discarded RTCM are the initial letters of the Radio Technical Commission for Maritime Services This is a commission established to define a differential data link for the real time differential correction of roving GPS receivers There are two types of RTCM differentia
277. ular grid running North and East and presumes that the earth is locally flat In a GIS the spherical coordinates of latitude longitude and height are translated into planar coordinates of northing easting and elevation Coordinates are expressed in TerraSync Software Getting Started Guide Coordinate Systems B the unit of measurement defined for the coordinate system for example meters Worldwide there are a number of standard grid coordinate systems defined The US State Plane grids are an example of this kind of grid coordinate system Transforming and projecting collected GPS positions Transforming real time corrected GPS positions When GPS positions are differentially corrected they use the datum or reference frame of the correction source Examples are e WAAS EGNOS ITRF2000 e NDGPS beacons NAD83 e NDGPS beacons in the Pacific Ocean NAD83 PACP00 Epoch 2003 0 e Europe beacons ETRF89 e OmniSTAR VBS US NAD83 e OmniSTAR VBS non US ITRF2005 e OmniSTAR HP XP worldwide ITRF2005 e VRS networks contact the system operator The usual convention is that SSF files store GPS positions in the WGS 84 datum which is almost identical to the ITRF2000 or ITRF2005 datums However coordinates in the NAD83 or ETRF89 datum can be up one meter apart from the same coordinates in the WGS 84 datum To resolve this issue the TerraSync software allows you to specify the datum of each real time correction source so that t
278. ved E Local intranet Enter your email address and password and then click Login The My Trimble page for your account appears 24 _ TerraSync Software Getting Started Guide Software Installation and Activation 2 b Scroll to the My Products section where any software that you have already registered appears Home Windows Internet Explorer Cek KeS v http support trimble com CPRS Home aspx x 4 x Google P zj File Edit View Favorites Tools Help Pd ae f oscar Approval or Review tome x 2 D db i page Tools gt My Products Add Click amp to see more details about a product Click a Serial Number value to update or extend details for that product Click the associated Your Reference value to add or modify Your Reference for that product Click the associated E to remove that product from this list You have registered the following products Product Name Serial Number Your Reference G GPS Pathfinder Office software 998363 00300 2 TerraSync Professional a Fees 998300 00110 rs Installation Software Installation Code 998300 00110 09182 44321 68D code Software Maintenance Expiry Date 29 Jun 2010 Activated on Device Name gt Juno SC Handheld Activated on Device Serial Number 99100073466243 Activation Date 1Deci2009 a Local intranet Qio 7 c Ifthe five lines below the TerraSync software do not appear click the beside the cop
279. ving between fields 63 TerraSync Software Getting Started Guide 225 Index overview 63 G GeoExplorer series handheld 47 geoid as reference level 192 default 193 definition 213 height 214 model 214 overview 188 GIS coordinate systems 190 191 data 211 earth models 189 GIS data converting to SSF format 130 exporting toaGIS 126 transferring to TerraSync 130 viewing 125 global shortcuts 66 good power level 60 GPRS access number 166 167 GPS troubleshooting 204 GPS Analyst extension post processing rove data 198 using with the TerraSync software 13 GPS field software connecting to Internet correction source 168 connecting to VRS network 168 GPS Pathfinder Office software post processing rover data 198 GPS Pathfinder Office software using with the TerraSync software 13 viewing data files in 125 GPS Pathfinder Office utilities Batch Processor 127 Connection Manager 127 Coordinate System Manager 193 Data Dictionary Editor 133 Data Transfer 118 Export 126 GPS Pathfinder Pro series receiver 47 GPS Pathfinder Pro XRS receiver 47 GPS Pathfinder XB receiver 47 99 GPS Pathfinder XC receiver 47 99 GPS position static 151 220 streaming 220 226 TerraSync Software Getting Started Guide GPS receiver battery level 58 troubleshooting 204 GPSNet VRS software 163 graphical screens 63 ereat circle distance definition 214 guest connection definition 214 HDOP definition 215 heading definition 214 Height Above Ellips
280. ving receivers that will use the corrections AN WARNING Enabling power output can damage some field devices Trimble recommends that you always select the Auto option unless you require power to the data radio and have protected the field device from power supplied by the GPS receiver For more information refer to the TerraSync Software Help To output real time corrections 1 Open the New File screen and start a new base data file 2 Step through the Base Station Setup wizard In the Real Time Output step do the following a Set the Correction Output field to Receiver Port or R8 Internal Radio b Choose an appropriate output format and message settings c Tap the Setup button beside the Correction Output field The Receiver Port Settings form appears Configure the receiver s communication settings baud rate data bits stop bits and parity to match those used by the data radio Note You cannot use the TerraSync software to configure the data radios communication settings You can only configure the receiver to use the same settings as the radio To change the data radios communication settings use the configuration software that is provided with the radio TerraSync Software Getting Started Guide 199 c 200 Setting up a Base Station Unattended base station If you do not want to log base data for postprocessing or if the base receiver can only output corrections you can set up the receiver as an unattended
281. w shows Bl Data and the Data section is active When you return to the Map section the screen or form that was open when you left the Map section appears again X Tip You can also use shortcuts to move between sections See Keyboard shortcuts page 66 Sections The main functions of each section in the TerraSync software are described below Map The Map section shows you all the features in the open data file Raster or vector map files can be displayed in the background for reference Use the Map section with the screens in the Navigation section to navigate to specific locations Data The Data section provides forms for entering information about features Use the Data section to update data from an existing GIS CAD or spatial database You can review edit and update the positions and attributes for features filter data to identify the features required for data maintenance accurately and efficiently collect the attributes and GPS position of geographic points lines and areas 80 TerraSync Software Getting Started Guide Panes Software Structure 4 switch to Camera mode if your device has an integrated camera to capture images This information is stored in one or more data files that you can transfer to the Trimble postprocessing software Data can then be exported into a wide range of GIS compatible formats Navigation The Navigation section provides forms for collecting and editing waypoin
282. want to register my copy over the Internet now option and then click Next The Register page opens in your default Web browser displaying the My Trimble account log in For more information see Registering the TerraSync software page 19 The Enter your Installation Code page appears TerraSync Desktop InstallShield Wizard Enter your Installation Code Please enter the Installation Code to install the software 10 Enter the installation code assigned to your copy of the TerraSync software when you registered the software and then click Next 46 _ TerraSync Software Getting Started Guide IL 12 13 14 Software Installation and Activation 2 In the Choose Desktop Software Location page select the folder where the setup will install the program files and then click Next The Tutorial page recommends that you should complete the tutorial in Chapter 4 of this guide before using the software Click Next The Start Copying Files page appears Click Next The final page of the installation wizard shows InstallShield Wizard Complete If you installed the software from the CD Trimble recommends that you download the latest software updates and documentation from the Trimble website www trimble com terrasync_ts asp Updating the TerraSync software Trimble recommends that you check for software and language updates after the installation process by going to www trimble com terrasync_ts asp Compatible GPS re
283. ware Connecting to a GPS receiver Configuring your required accuracy settings Configuring GPS and data logging settings Creating a new data file Creating a point feature using Log Now Creating a line or area feature using Log Later Ending the data collection session Updating data Working from the map Common status indicators The TJerraSync Software Quick Start Guide is provided as a printed card and is also available as a PDF file on the TerraSync Software CD 14 TerraSync Software Getting Started Guide Introduction 1 Release Notes The TJerraSync Software Release Notes describe new features in this version of the software and any changes to the documentation and provide any information not included in the product documentation The release notes are provided in the box with the software They are also provided as a PDF file on the ZerraSync Software CD Technical assistance If you have a problem and cannot find the information you need in the product documentation contact your Trimble reseller Technical support Go to the TerraSync software technical support page www trimble com terrasync_ts asp for the latest support information about the software including e FAQs e Support notes detailing the latest support issues e Documentation e The latest files available for download Windows error reporting If a Microsoft Windows Error Reporting dialog appears indicating that the TerraSync software has encountered
284. ware Trimble strongly recommends that you transfer coordinate systems to the field device in a coordinate system export file This is preferable to selecting and sending a single coordinate system Transferring a coordinate system export file Use the Trimble Data Transfer utility to transfer a coordinate system export file to the TerraSync software A coordinate system export file can contain a number of coordinate systems and sites To transfer a coordinate system export file 1 Connect the field device to the office computer start the Data Transfer utility and connect to the appropriate device definition For detailed instructions see the TerraSync Software Getting Started Guide 2 Select the Send tab 3 Click Add and select Coordinate System Export File from the drop down list The Open dialog appears showing all coordinate system export cse and csw files in the default location for coordinate system files C Program Files Common Files Trimble Geodata 4 Browse for the correct drive and folder if necessary then select a cse file and click Open Note If you select more than one cse or csw file to send only the coordinate systems in the last file you transfer will be loaded into the TerraSync software Each transferred file replaces any previously transferred files 5 The Open dialog disappears The selected coordinate system export file is added to the Send list in the Data Transfer dialog 6 Click Transfer
285. with the license grant and installation restrictions in this Agreement In the event the compliance check reveals that the number of installations or concurrent users of the Software licensed hereunder exceeds the actual number of licenses obtained by you you agree to promptly reimburse Trimble three 3 times the then current applicable list price for the extra licenses that are required to be compliant but that were not obtained as liquidated damages and as a reasonable penalty The foregoing remedy is not exclusive 1 3 Termination The license is effective until terminated as provided herein You may terminate this Agreement by ceasing all use of the Software and destroying or returning all copies Without prejudice as to any other rights Trimble may terminate this Agreement with or without notice if you fail to comply with the terms and conditions of this Agreement In such event you must cease its use destroy all copies of the Software and of its component parts 1 4 Copyright All title and copyrights in and to the Software including but not limited to any images photographs animations video audio music and text incorporated into the Software the accompanying written materials and any copies of the Software are owned by Trimble and its suppliers You shall not remove cover or alter any of Trimble s patent copyright or trademark notices placed upon embedded in or displayed by the Software or on its packaging and related mat
286. ws that the TerraSync software is receiving real time corrections from an external beacon receiver such as a GeoBeacon receiver Ts By Real time beacon icon Shows that the TerraSync software is receiving real time corrections from a beacon yee wi Real time satellite icon Shows that the TerraSync software is receiving real time corrections from a satellite differential service hh at A Real time SBAS icon Shows that the TerraSync software is receiving real time corrections from an SBAS satellite Note If the real time signal is lost the current real time icon flashes If the icon is flashing and the number of satellites being used is greater than 0 the TerraSync software is using autonomous uncorrected GPS to calculate its position If no icon is visible the TerraSync software has not been configured to use a real time correction source Battery icon The left half of this icon indicates the charge level of the GPS receiver battery if one is connected If the connected receiver does not provide battery status information to TerraSync the left half of the battery icon is empty e The right half indicates the charge level of the field computer battery When the battery of the GPS receiver or field computer is fully charged the corresponding half of the battery icon appears green The level of green drops as the corresponding battery charge level drops e When the power level is low the correspo
287. y by automating repetitive tasks such as data transfer differential correction and export to GIS When you return to the office connect the field computer to the office computer The Connection Manager utility automatically recognizes that a field computer is connected and runs the Batch Processor utility For more information about these utilities refer to the GPS Pathfinder Office Software Help TerraSync Software Getting Started Guide 127 5 Tutorial Collecting Data Exercise 5 Preparing for data update 128 Note You cannot update imported data files using the TerraSync Standard edition software With the TerraSync software version 4 10 if you also have CoPilot Live 7 Professional for Trimble TerraSync software or TomTom Navigator 6 turn by turn navigation software installed on the device the TerraSync software automatically switches to the navigation software to navigate to the selected target then switches back when you have arrived at the destination To continue using the TerraSync software for navigation as covered in this tutorial go to Navigation Options Turn by turn Turn by turn navigation and select Off For more information on using Turn by turn navigation software with the TerraSync software refer to the TerraSync help Some time has passed and you must return to Starfish Bay to check the condition of the traffic signs You will navigate to each sign using the TerraSync software and a real time co
288. y collected _ status Not Transferred DD Sample in this data file 7 Tap the Subsection list button and then select Collect Features You can now record new features in the open data file TerraSync Software Getting Started Guide 107 5 Tutorial Collecting Data Collecting an area feature using averaged vertices In Exercise 2 you collected data for the park in Starfish Bay Now you need to collect data for a new sand box in Starfish Park The sand box is in the shape of a triangle and can be collected as a series of averaged vertices You must record GPS positions at each vertex of the feature which the TerraSync software then averages to compute one position for each vertex Sane Box To record an area using vertices 1 Tap the Subsection list button and then select Collect Features 2 Tap Options and then select Log Later 3 Tap the Sand Box feature and then tap Create 4 Tap Options and then select New Vertex AET we ok The Vertex form that appears contains the same fields as the attribute entry form collect z Options Pause m The software starts logging GPS positions for the averaged vertex and the logging icon in the status bar changes to 4 The number beside it shows the number of positions logged for this vertex 5 Once you collect enough GPS positions for the vertex tap OK 6 Repeat Step 4 and Step 5 for each vertex 7 Enter Starfish Sand Box in
289. y link as specified by the supplier Consult the supplier if necessary You have set the station ID incorrectly In the Real time Settings form see page 88 check that you have set the Station ID field correctly You have configured the real time settings incorrectly In the Real time Settings form see page 88 check that the settings under the External Source heading match the telemetry link and the transmitted RTCM data stream TerraSync Software Getting Started Guide 205 D Troubleshooting Data files This section lists problems you may encounter with data files Problem Possible cause Solution You cannot update a feature add new features or open a data file You are using the TerraSync Standard edition software which does not allow you to open imported files In this edition of the software any file that you transfer from the office computer create from Shapefiles or receive by email is marked Not Usable Upgrade to the fully functional TerraSync Professional edition software The file is already open in the background of the Map section Set the map background file to None Select another file for the map background Position updates are not allowed Set the Allow Position Update field see page 88 on the Logging Settings form to Yes or Confirm You cannot change settings or use some menu items You cannot unlock a configuration file The
290. y of the TerraSync software that you have just registered The Installation Code field shows the installation code for your copy of the TerraSync software Make a note of this code You need to enter this code when you install or reinstall the software You can also check which device the registered Installation Code has been activated on TerraSync Software Getting Started Guide 25 2 26 Software Installation and Activation Installing the TerraSync software This section describes how to install the TerraSync software It provides information about the following options e Installing a translation of the TerraSync software see below e Installing the TerraSync software onto a Windows Mobile powered device page 26 e Activating the software on a field computer powered by the Windows Mobile version 5 0 software or version 6 operating system page 37 e Installing the TerraSync software onto a Windows computer page 43 Installing a translation of the TerraSync software Trimble recommends that you install a translation of the TerraSync software only on a field computer that has the corresponding language version of the operating system installed For example install the Japanese TerraSync software on a field computer that has a Japanese Windows operating system installed Note The Regional Options applet in the Control Panel changes only the display of date time units and currency information It does not change the langua
291. ystem the office computer is running If the computer is running e Windows Vista or Windows 7 make sure you have downloaded and installed the Windows Mobile Device Center e Windows XP make sure you have installed the appropriate version of Microsoft ActiveSync technology For more information see Step 1 Install Microsoft connection management software onto the computer page 27 To transfer files between a desktop computer and a field computer running the TerraSync software you must also have one of the following installed on the desktop computer e the Trimble Data Transfer utility which is available on the TerraSync Software CD or for free download from www trimble com datatransfer shtml e version 4 20 or later of the Trimble GPS Pathfinder Office software 18 TerraSync Software Getting Started Guide Software Installation and Activation 2 Registering the TerraSync software Before you can install the TerraSync software you must register your copy of the software to obtain an installation code that you enter during the installation process You can only register your copy of the TerraSync software once For information about obtaining your installation code when the software has previously been registered see Obtaining your installation code after registration page 24 Trimble recommends that you register before beginning installation To register you need e the Proof of Purchase Number POPN from the Ter

TerraSync Software Getting Started Guide

Contents

Download Pdf Manuals

Related Search

Related Contents