LED Moving Head
Contents
1. hed color 2 Safety Instructions CAUTION Be careful with your operations With a dangerous voltage you can Suffer a dangerous electric shock when touching wires This device has left the factory in perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual ES Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to temperature changes due to environmental changes do not switch it on immediately The arising condensation could damage the device Leave the device switched off until it has reached room temperature This device falls under protection class Therefore it is essential that the device be earthed The electric connection must carry out by qualified person The device shall only be used with rate voltage and frequency Make sure that the available voltage is not higher than stated at the end of this manual Make sure the power cord is never crimped or damaged by sharp edges If this would be the case replacement of the cable must be done by an authorized dealer Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging2. 512 control connections Connect the provided XLR cable to the female 3 pin XLR output of your controller and the other side to the male 3 pin XLR input of the moving head You can chain multiple Moving head together through serial linking The cable needed should be two core screened cable with XLR input and output connectors Please refer to the diagram below DMX output DMX Input 3 Pin XLR Socket 3 Pin XLR Socket 1 Ground 2 Signal 3 Signal lt gt DMX512 120 Ohms SS DMX controlle Address 26 Address13 Address 1 DMX 512 connection with DMX terminator For installations where the DMX cable has to run a long distance or is in an electrically noisy environment such as in a discotheque it is recommended to use a DMX terminator This helps in preventing corruption of the digital control signal by electrical noise The DMX terminator is simply an XLR plug with a 120 resistor connected between pins 2 and 3 which is then plugged into the output XLR socket of the last fixture in the chain Please see illustrations below 1200 PIN 3 PIN 2 6 LCD Display Operations Te RETREAT gt press menu to back Pan invert e A OR Ka press menu to back Pan angle Enter up down Enter press menu to hack BAO 630 Enter up down Enter Fiction gt MER or PR Top A S press menu to hack Enter DMX 512 re press menu to back Fntar Enter up down press menu to back Slav
3. the power cord During initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective it should decrease gradually Please don t project the beam onto combustible substances Fixtures cannot be installed on combustible substances keep more than 50cm distance with wall for smooth air flow so there should be no shelter for fans and ventilation for heat radiation If the external flexible cable or cord of this luminaire is damaged it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard 2 3 Operation Instructions The moving head is an LED wash light for onsite decoration purpose Don t turn on the fixture if it s been through severe temperature difference like after transportation because it might damage the light due to the environment changes So make sure to operate the fixture until it is in normal temperature This light should be keep away from strong shaking during any transportation or movement Don t pull up the light by only the head or it might cause damages to the mechanical parts Don t expose the fixture in overheat moisture or environment with too much dust when installing it And don t lay any power cables on the floor Or it might cause electronic shock to the people Make sure the installation place 1s in good safety condition before installing the fixt
4. CE LED Moving Head 36 10w ZOOM User Manual KEEP THIS MANUAL FOR FUTURE NEEDS Version 20 1 Dispacking Thank you for choosing our moving head For your own safety please read this manual before installing the device This manual covers the important information on installation and applications Please install and operate the fixture with following instructions Meanwhile please keep this manual well for future needs This moving wash is made of a new type of high temperature strength of engineering plastics and cast aluminum casing with nice outlook The fixture is designed and manufactured strictly following CE standards complying with international standard DMX512 protocol It s available independently controlled and linkable with each other for operation And it is applicable for large scale live performances theater studio nightclubs and discos The fixture adopts powerful LED lamps which features high brightness and Stability Please carefully dispack it when you receive the fixture and check whether it is damaged during the transportation And please check whether the following items are included inside the box Moving Head one Signal Cable one Omega Clamp one User Manual one circus lifeline one Hook one 10 Maintenance and Cleaning The following points have to be considered during the inspection 1 All screws for installing the devices or parts of the device have to be ti
5. V Power Consumption 360W Dimensions 350x260x350mm Packing Dimensions 425x295x400mm Net Weight 9kgs Gross Weight 11kgs Channel Funct i on Val ue Descri pti on Pt PAN oss saoe30 O 2 PANI6bit 0 255_ 18degree O 3 Tilt o 255 fo 200 4 Tilt 16bit 0 255 18 degree 5 Dimmer 0 255 0 100 000 006 No function lt sSSCid Strobe 070 128 Pulse strobe from slow to fast 7 Red 0 255 0 100 8 Green 0 255 0 100 9 Blue 0 255 0 100 10 White 0 255 0 100 11 ZOOM 0 255 0 100 12 Scan Speed 0 255 From fast slow RGBW macro 167 178 Green red from bright to dark function a dak o brighi p N Nn T N Nn Nn O zl ge Sc oo XR jas t a Nn o Eh 4 Installation via clamp Please refer to the picture below 1 Omega holders 2 Clamp 3 Safety rope 4 Quick lock fastener Screw one clamp each via a M12 screw and nut onto the Omega holders Insert the quick lock fasteners of the first Omega holder into the respective holes on the bottom of the device Tighten the quick lock fasteners fully clockwise Install the second Omega holder Pull the safety rope through the holes on the bottom of the base and over the trussing system or a safe fixation spot Insert the end in the carabine and tighten the safety screw 4 5 DMX
6. e mode Enter sound mode press menu to back Enter auto mode press menu to back Enter Enter up down Enter up down Manually operate Manual Date xxx Choose channal Number of controlled Restore All the motor reset All the data change to original The display will close after 30 seconds without operations
7. ghtly connected and must not be corroded 2 There must not be any deformations on the housing color lenses fixations and installation spots ceiling suspension trussing 3 Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances 4 The electric power supply cables must not show any damage material fatigue or sediments Further instructions depending on the installation soot and usage have to be adhered by a skilled installer and any safety problems have to be removed CAUTION Disconnect from mains before starting maintenance operation In order to make the lights in good condition and extend the life time we suggest a regular cleaning to the lights 1 Clean the inside and outside lens each week to avoid the weakneness of the lights due to accumulation of dust 2 Clean the fan each week 3 Adetailed electric check by approved electrical engineer each three month make sure that the circuit contacts are in good condition prevent the poor contact of circuit from overheating We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents There are no serviceable parts inside the device Please refer to the instructions under Installation instructions Should you need any spare parts please order genuine parts from your local dealer 10 Beam opening rm Baam opening rr Baam Openings Beam opening
8. ure Make sure to put the safety chain and check whether the screws are screwed properly when installing the fixture Make sure the lens are in good condition It s recommended to replace the units if there are any damages or severe scratch Make sure the fixture is operated by qualified personnel who knows the fixture before using Keep the original packages if any second shipment is needed Don t try to change the fixtures without any instruction by the manufacturer or the appointed repairing agencies It is not in warranty range if there are any malfunctions from not following the user manual to operate or any illegal operation like shock short circuit electronic shock lamp broke etc eE 8 Technical Specifications 36PCS 10W high power LEDs 50 000 hours lifespan and low power consumption 16 bit smooth and precise resolution for PAN TILT movement 540 7 630 pan and 280 tilt movement Scan position memory auto reposition after unexpected movement RGBW color mixing system 8 ZOOM 15 60 LED dimming DIM4 technology adopt 4096 linearity dimmer LED rainbow effect Macros effect Strobe effect with 20 flashes per second and pulse effect General dimming and blackout for all four colors 14 DMX channels DMX512 master slave and sound activated controllable or auto operation Blue background LCD display Input Voltage AC90 240V 50 60Hz Fan standard size 90X90X25 60X60X15 Fuse standard at the bottom 3 15A 250
Download Pdf Manuals
Related Search