A951 Abduction
Contents
1. A951 OWNERS MANUAL ASSEMBLY INSTRUCTIONS 4 Ed i i h it W me m e eee ee ee ae ae ae ao ae ae am ww ao ao ae wm mw ww ao ao ao ww ae ao ao ao ao am ao wr ww ae ao ao ao am am am ao ao ao ao oao am ae am am ao ao ao am am ao a ao ad ABDUCTION SportsArt FITNESS A SAFETY INSTRUCTIONS Read all cautions warnings and obtain proper instruction on use of the machines prior to using Use appropriate positioning and controlled movements Assemble and operate the strength on a solid level surface Do not use outdoors or near water Never allow children on or near the strength Make sure all fasteners are properly tightened for safety DO NOT use the strength if the unit is disassembled in any way Keep head limbs and fingers clear of all moving parts If at any time during exercise you feel faint dizzy or experience pain stop and consult you physician DO NOT wear loose or dangling clothing while using the equipment Keep away from all moving parts Use care when mounting and dismounting the unit DO NOT use any accessories that aren t specifically recommended by the manufacturer These might cause injuries or cause the unit to fall Close supervision is necessary when this strength is used by on or near adolescent invalids and disabled persons Use this strength only for its intended use as described in this manual Never operate this strength if it has been damaged in any way If it is not work2. ews and washers that you just removed from step 1 See Fig 8 Fig 8 Usage Instruction www sportsartfitness com CAUTION Do not allow people near the machine when in use Do not use the machine if you are unfamiliar or do not know how to operate this equipment 1 Select a resistance level and starting position that enable you to perform the movement correctly 2 Place thighs together and ina parallel starting position with pads on the outside of the leg and feet are placed on the footrests G Grasp firmly the handles at both sides of the seat 4 Push your thighs outward Make sure that the upper body is maintained i an upright position against support Perform the exercise in a controlled manner Exhale when pushing against resistance
3. ews by hex key wrench Fig 4 5 Assemble the plate and secure screws by hex key wrench as shown in Fig 5 NOTE To avoid painting off please make sure the plate not to hit the steel plate during the assembly E BELT ADJUSTMENT 1 If the belt is too tight or too loose first loosen nut A as shown then adjust nut B If the belt length is too long adjust downward if the belt length is too short adjust upward Adjust the belt to the proper position then tighten nut A N The gap between nut A and B must be within 35mm 1 4 If the gap still exceeds the 35mm limit after the first step please loosen the screws on C and adjust the belt to the proper length Tighten the screws and follow the 1st step again See fig 6 Oma i CON TR Gr Ro f We OA ae SY D a 5 a Se LP Cont eS a bh T gt S Fig 6 q F HOW TO USE THE MINOR WEIGHT STACK 1 To adjust the minor weight stack insert the upper pin to add 3 5Lbs 1 5kgs or the lower pin to add 6 5Lbs 3kgs 2 Pull the pin to release the weight See fig 7 3 5Lbs 1 5Kgs ys 6 5Lbs 3Kgs 4 ad oy Fig 7 G STORAGE TRAY ASSEMBLY 1 Remove the existing screws and washers from tubing 2 Place storage tray onto tubing and tighten with the scr
4. ing properly been dropped or damaged contact your dealer DO NOT attempt to fix a broken or jammed machine Notify floor staff Never drop or insert any object into any opening B Introduction Badge rear Badge front Side frame Front cover B Usage sticker Left pad Rear cover Saia Front cover A nae Selection pin 3 5 Lbs 1 5 kgs Selection pin 6 5 Lbs 3 kgs Cord Stack fork Weight stacks 11 L ki Maitane eight stacks 11 Lbs 5 kgs Seat Right pad Multi conjoint Foot mat bar Ring Ring shapped plate A sh eee Ring shapped plate C Foot plate Setting control bar C List of Parts One double end open wrench 8mm x 10mm 2 One double end open wrench 8mm x 17mm 3 One double end open wrench 12mm x 15mm 4 One double end open wrench 17mm x 23mm 5 One hex key wrench M4 6 One hex key wrench M5 7 One hex key wrench M6 8 User s manual 9 One storage tray D STEP BY STEP INSTRUCTION 1 Hold the side frame during assembly then connect the frame to the side frame Secure screws tightly as shown in Fig 1 Fig 1 2 Screw up the belt with open wrench 10 mm amp 12 mm as shown in Fig 2 Fig 2 3 After assembly the belt please check the belt to see if it located inside the pulley Fig 3 4 Assemble the foot mat as shown in Fig 4 and faster 4 scr
Download Pdf Manuals
Related Search