User manual Mobeye® i110
Contents
1. sensor a sensor test can be executed e Enter your user code e Press menu e Press 11 e Press OK A confirmation beep is heard First the green light will be flashing After about 30 seconds the light will be on continuously In this mode the sensor test can be done each time the sensor detects a movement a repeating beep will sound Leave the test by entering OK twice 1 8 MOBEYE SETTINGS The Mobeye settings can be added via the keypad and SMS text messages First the possible settings are discussed later the way of programming 1 8 1 Possible settings 1 8 1 1 Change the user code The user code is the code for switching on off the active status In the active status the Mobeye will detect movements The user code is also needed to program the settings or activate the special functions It is possible to change the user code to any 4 digit number In case the user code is entered incorrectly 3 times the indicator turns red and the Mobeye will be blocked during 10 minutes 1 8 1 2 Change telephone numbers The SMS alarm message and voice alarm signal message can be sent to one or two telephone number At least one telephone number must be entered in the Mobeye The test messages and low battery messages are sent to the first programmed telephone number 1 8 1 3 Sensor sensitivity The detectors sensitivity can be changed to a high or low er value 1 High 2 Low In the high sensitivi2. setting Te Press OK The light switches off a confirmation melody is played personal code turns green belonging to the setting to be changed In case of false entries the light turns red and a short beep will sound The menu can be left from any position by twice pressing OK Following settings are possible Menu nr Description Options Factory setting 00 Change user code 4 digit code 1111 01 Change 17 tel nr Tel number 0 to delete 02 Change 2 tel nr Tel number 0 to delete 03 Sensor sensitivity 1 2 1 high 04 Entry delay 15 30 45 or 60 15 sec 05 Interval test message 0 30 days 0 no message 07 Entry indication 0 off 1 on 0 08 Siren 0 off 1 on 0 41 Change minimum temperature 000 050 0 until 50 C 999 110 101 10 until 1 C 999 off 42 Change maximum temperature 000 050 0 until 50 C 999 110 101 10 until 1 C 999 off 49 Correction factor temperature 01 09 1 to 9 C 00 11 19 1 to 9 C 00 no correction 1 9 1 1 Configuration of extra text via SMS text message It is possible to send an extra text in the SMS text messages in order to recognize which Mobeye the message has sent This text max 20 characters can be programmed by sending an SMS to the Mobeye Please follow the instructions Switch the Mobeye into the programming mode In this mode the GSM module is switched on and is able to receive me
3. ery life The test message only works if the system is on or a temperature limit is set 1 8 1 10 SMS Recognition text It is possible to send an extra text in the SMS text messages in order to recognize from which Mobeye the message has been sent The first part of the SMS text message will always contain standard text like Mobeye alarm or Test message OK The recognition text will be written after the standard text This text max 20 characters can be programmed by sending an SMS to the Mobeye 1 8 1 11 Alarm monitoring center For some countries the Mobeye has been prepared to send the alarm and test message to an alarm monitoring center instead of to private telephone numbers Please check the website or contact www mobeye eu to inquire for the actual status in your country 1 8 2 Receive the settings in an SMS It is possible to send the programmed settings to your GSM e Enter your user code e Press menu e Press 10 e Press OK In about 30 seconds the telephone programmed at memory place 01 will receive the settings in an SMS text message 1 8 2 1 Reset to factory settings After entering your personal code menu 99 OK the Mobeye is back to factory settings You personal code will be 1111 again 1 9 CONFIGURATION To change the settings please follow the instructions e Enter your 4 digit Press menu gt light Enter the menu number w Press OK Enter the new
4. ights the translation included are reserved Any reproduction either photocopy microfilm or saved in an automated data dictionary only after written approval of the Publisher Reprinting even in summary is prohibited This user manual meets the technical requirements at the moment of printing Changes in technology and equipment are reserved Copyright 2011 by Mobeye version 1110EN110201 Mobeye
5. inimum and or maximum temperature The Mobeye will monitor the actual temperature and sends an alert as soon as the temperature reaches the limit Low battery message The Mobeye will send an SMS text message in case the batteries must be replaced After this you need to change the batteries as soon as possible For some time the Mobeye remains functioning as normal Even when the Mobeye is unset it will measure the battery strength and send the message 1 HOW TO USE THE MOBEYE 1 1 TO GET READY IN THREE STEPS To get started with the Mobeye only three steps are needed 1 Place the SIM card in the Mobeye Make sure this SIM card is not secured by a PIN code 2 Place the four batteries 3 Enter at least one phone number in the Mobeye 1 2 STEP 1 SIM CARD To use the Mobeye a SIM card of any provider is needed On this SIM card the PIN code security needs to be disabled If you have a SIM card with PIN code you can disable this using any mobile phone and switch off the PIN code security Please consult the manual of the used mobile phone for the procedure The SIM card needs to be placed before the batteries When using a prepaid SIM card take care of the remaining value Apart from that it is wise to set a recurrent test message in the menu so the card will be used at least once a month e Open the ol Mobeye e Place the SIM HLL card e Place the batteries e Close the Mobeye 1 3 STEP 2 PLACE THE BATTERIES P
6. lace the four lithium 3 0 volt batteries CR123 When replacing the batteries all settings remain unchanged After placing the SIM card and the batteries the Mobeye will perform a self test during 1 minute During the test the light is red In case the light is flashing red a problem with the SIM card is detected A reason could be no SIM card was placed or the PIN code security of the SIM card was not disabled 1 4 STEP 3 PROGRAM THE PHONE NUMBERS You need to program at least one phone number in the unit This phone number is used to send the messages to Enter your 4 digit user code factory setting 1111 Press menu Enter 01 01 for the 1st phone number 02 for the 2nd phone number Press OK Enter the phone number e g 0612345678 Press OK The light turns green and a confirmation melody is played The Mobeye is ready to use 1 5 SWITCHING THE MOTION DETECTOR ON OFF 1 5 1 Switching on To activate the Mobeye motion detector with your personal user code e Enter your user code e Press OK The light turns red shortly and an indication tone is started This repetitive tone will last during the exit delay of 30 seconds As soon as the acoustic signal stops the Mobeye is active In case the user code is entered incorrectly 3 times the indicator turns red and the Mobeye will be blocked during 10 minutes 1 5 2 Switching off To de activate the Mobeye motion detector with you
7. mable gases vapours or dust are present or could be present Reparation of the device may only be carried out by people trained for Mobeye repair In case the device must be repaired only original replacement components may be used The use of different parts may lead to damage of the Mobeye Use in accordance with the regulation The use of this device in accordance with the regulation is the generation of SMS text messages and telephone calls after detection of a motion by the motion detector or of a temperature that outreaches the programmed limits Other usages are not permitted Introduction The Mobeye is an easy to install alarm system that will notify you in case lt a of a detection using the built in GSM ee To use the Mobeye you will need a SIM card of any provider Typical applications are the security of places without any power supply or the temporary security of objects The Mobeye has the following features Alarm notifications after movement detection In case of the detection of an intruder the Mobeye will send an SMS text message to your phone s The Mobeye will also call the phone numbers in order to be sure the message is not missed It is also possible to let the siren sound After an alarm the Mobeye will be in standby status for about 5 minutes Hereafter it is able to report new movements Alarm notifications after detection out of range temperature It is possible to program a m
8. mobcye User manual Mobeye i110 SW version 3 N Table of content 1 How to Use the Mobeye 1 To get ready in three steps 2 Step 1 SIM Card 3 Step 2 Place the batteries 4 Step 3 Program the phone numbers 9 Switching the motion detector on off 1 5 1 Switching on 1 5 2Switching off 6 Test GSM network strength 7 Sensor test 8 Mobeye settings 1 8 1Possible settings 1 8 2Receive the settings in an SMS 9 1 Configuration 2 Issue solving 3 Technical data OO QO 0O N N N N 9 9 O QI RE E A a A Attention Very important This user manual contains important guidelines for the installation and usage of the Mobeye i110 Please read these thoroughly before you start using the Mobeye In case of damage caused by disregarding the guidelines the warranty expires The user must regularly check the proper functioning of the Mobeye The manufacturer cannot be held liable for any damage caused by any incorrect use or incorrect functioning of the Mobeye Safety guidelines The permitted ambient temperature during operation may not be exceeded not lower than 10 C and not higher than 55 C The device is intended for use in dry and clean places Protect the device from moisture heat and water splashing The guidelines for the battery usage must be regarded e Do not expose the device to strong vibrations e Do not let it fall from height e Do not use in an environment where any inflam
9. mperature is too high or too low an SMS text message is sent followed by a telephone call As long as the out of range temperature remains the report will be repeated hourly Once the temperature is back to normal the Mobeye confirms this to you This function is active as soon as a temperature limit is programmed By resetting the limits the function becomes inactive 1 8 1 8 Adjusting the temperature The built in temperature sensor may have a standard deviation of the actual temperature In this case the deviation will be similar at all temperatures It is possible to correct the temperature deviation in the Mobeye i110 In the SMS setting summary you see the reported temperature If a correction is specified it is processed in the displayed temperature the correction factor itself is displayed separately Example Mobeye temperature 13 C Actual temperature 14 C To correct this deviation one degree should be added 1 8 1 9 Interval test message The Mobeye can send test messages Through these test reports you will be ascertained of the proper functioning of your Mobeye You can set the interval between the reports indicate the number of days between reports This is adjustable between 0 no test reported and 30 monthly test message Note the interval of 1 day will result in a daily test message the exact time between the message will be about 24 hours The smaller the interval between the test reports the shorter the batt
10. ned on shortly No valid Telephone number was entered Enter a valid number The light is flashing during switching on No valid SIM card was entered or the SIM card was not made pin code free Check the SIM card It is impossible to change the settings After entering your personal code followed by menu the error tone is played and the light turns red Mobeye is activated Switch off the Mobeye No GSM reach during the GSM test No network is available belonging to the SIM cards provider Choose another network provider The light remains red You entered a false user code three times Wait 10 minutes and then re enter the correct user code You do not receive a SMS with the settings Telephone number is not correct Re program the telephone number Change the menunr 06 to 01 For other questions please refer to the site www mobeye eu 3 TECHNICAL DATA GSM Tri Band EGSM 900 1800 1900 MHz compatible to the ETSI GSM Phase 2 standard Output power Class 4 2W 900 MHz Class 1 1W 1800 and 1900 MHz Temperature range 10 C until 55 C Weight ca 275 gram incl batteries Dimensions 161 x 90 x 35 mm LxWxH e Batteries 4x CR123 Lithium 3 0 V Power 50 pA short peaks of max 2 A Support For support on technical problems regarding Mobeye please contact info mobeye eu This manual is published by Mobeye All r
11. r personal user code e Enter your user code e Press OK The light switches to green and a confirmation melody is played 1 6 TEST GSM NETWORK STRENGTH Before using the Mobeye is it advised to test the GSM reach at the place where the device is to be placed Enter your user code Press menu Press 12 Press OK First the light turns red The Mobeye now switches on the GSM modules and searches for all present networks It also checks the network strength of the SIM card provider in the device As soon a the GSM network is found the light will turn green The GSM reach of the used SIM card can be read from the LED indicator LED Description Green during 30 seconds Reach is good Flashing green Reach is bad Red No reach Flashing red No valid SIM card or Sim card is not pin code free Besides the telephone number at memory place 01 will receive an SMS text message containing all existing GSM networks sorted by provider It also tells the strength per network This search function can take some minutes In case you want to leave the function before it is ready please press OK twice Warning In case of a weak signal the Mobeye can still be used but there is a risk that message cannot be sent or will be received with a delay In case of no reach it is advised to use a SIM card of a provider with a stronger network 1 7 SENSOR TEST In order to check the reach of the
12. ssages Enter your 4 digit personal code factory setting 1111 Press menu Press 21 gt light turns green Press OK The Mobeye first prepares the programming mode The light flashes red interval ca 1 sec As soon as the light turns green the Mobeye In order to program the extra message text send an SMS in following structure is able to receive SMS messages e lt user code gt name xxxxxx Please regard the dots between and behind the commands command name in small letters Example enter the text boat evergreen e g user code 1111 e 1111 name boat evergreen You will hear two short beeps in case of a correct command Leave the menu by pressing OK twice 1 9 1 2 Special functions Via the keypad it is possible to activate some special functions e Enter your 4 digit personal code e Press menu gt light turns green e Enter the menu number belonging to the function e Press OK Menunr Description 10 Send an SMS containing the settings to the 1 telephone number 11 Activate sensor test 12 Test GSM network strength 13 Test siren 21 Start SMS programming mode 99 Reset to factory settings 1 9 1 3 Leave the menu The menu can be left from any position by pressing OK twice 2 ISSUE SOLVING Error Possible reason Solution Mobeye cannot be switched on You hear an error tone the red light is tur
13. ty mode each detection will provoke an alarm In the lower sensitivity mode the alarm will be provoked in case two detections are measured within a time frame of 15 seconds This mode prevents false alarms in case of e g draught and is most suitable in case the sensor is directed towards an open space 1 8 1 4 Entry delay It is possible to choose from 4 entry delay times The entry delay is the time between the moment of detection and the moment of sending the first SMS text message Take care in case the GSM network has a low reach the time can be longer in case the network connection was not established within the time of the entry delay 1 8 1 5 Entry indication It is possible to hear an indication beep during the entry delay This can be used as a reminder that the Mobeye is in active mode 1 8 1 6 Siren After the entry delay the siren can sound during two minutes At the same time the SMS text messages and telephone calls will be done At soon as the Mobeye is switched off the siren will stop It is possible to test the loud alarm During the test the siren will be heard until it is cancelled by lt OK gt lt OK gt This test is also possible in case the Mobeye i110 is programmed as a silent alarm 1 8 1 7 Temperature alarm The Mobeye is able to send a temperature alarm as soon as the actual temperature reaches a programmed min or max level This function can be used independently of the motion detection As soon as the te
Download Pdf Manuals
Related Search