Home

e-360 a modifier

1. 360 VERSION WARNING DAILY INSPECTION On EE version the following additional parts must be properly installed at all time motor enclosing kit headbands on bolt ends part no A91 107A the enclosing bands must be installed to cover ventilating holes amp access for brush maintenance splash pan under vehicle front portion of frame accelerator cable protector cover of the power control box battery cover locking device Static strap part no 090330 Motrec part no 2450001 accessories and seat switch protectors ELECTRIC CONTROL MODIFICATION the brake light switch has been replaced by a pressure switch part no 3669004 OPERATOR AND MAINTENANCE MANUAL SPARE PARTS LISTS INCLUDED SERIAL NUMBER 1030841 amp UP Printed in Canada One Year Limited Warranty Effective April 25 2005 MOTREC Inc MOTREC hereby warrants to the Original Retail Purchaser Owner that any of its vehicles shall be free from any defect in materials for a period of 90 DAYS while in the possession of such Original Retail Purchaser This warranty IS NOT TRANSFERABLE to any subsequent Buyer The warranty period is extended to one year or one thousand 1 000 hours which ever first occurs on the electric motor differential parts that bathe in oil and the electronic speed controller MOTREC makes no warranty or representation with respect to the internal combustion engine tires and batteries since their
2. 4 or 6 passengers option 49 PART NO 2801000002 2802000001 2801000001 2399000014 3113000001 2800000002 2800000001 2366320001 2366320002 2366320003 2367300001 2367300002 DESCRIPTION REAR VIEW MIRROR TRIM DOOR SIDE MIRROR SIDE MIRROR BRACKET WIPER MOTOR WIPER ARM DOOR HANDLE DOOR HANDLE BAR DOOR LEVER REAR GLASS WINDSHIELD Spare Parts DIFFERENTIAL AND REAR SUSPENSION TS 50 Spare Parts REF gt UC 12 13 14 15 16 17 18 19 20 21 22 23 24 27 28 29 PART NO 481433 302002 3173300001 242053 2910000001 481430K 481431K 481430RK 242056 2420011 242057 2420010 242058 242059 2113000001 2113300002 2122236001 242060 242061 3620004 2320006 242063 242064 242065 242066 242067 242069 242070 242071 DESCRIPTION DISC HYDRAULIC BRAKE REAR AXLE BEFORE SERIAL 0710276 SERIAL 0710276 amp UP LOCK WHEEL STUD LEFT CALIPER RIGHT CALIPER REPAIRE KIT CALIPER OIL SEAL BEFORE SERIAL 0611200 SERIAL 0611200 amp UP NEEDLE BEARING BEFORE SERIAL 0611200 SERIAL 0611200 amp UP NUT FLAT WASHER PULLEY W80 PULLEY W90 MOUNTING PLATE CALIPER OIL SEAL TAPERED BEARING HOUSING SPACER BREATHER SPACER TAPERED BEARING SHIM GEAR KIT SHIM TAPERED BEARING CASE REF PART NO 30 3l 32 33 34 35 36 37 3 39 42 43 44 45 46 47 48 58 59 60 61 62 63 64 EM 242072 242073 242074 242
3. current sensor or motor fault not used throttle fault static return to off SRO fault high pedal disable HPD fault emergency reverse circuit check fault contactor driver overcurrent welded main contactor precharge fault missing contactor or main cont did not close low battery voltage overvoltage thermal cutback due to over under temp anti tiedown fault ONDE RON EE 0 1 1 1 1 2 2 2 2 3 3 3 3 4 4 4 4 NOTE Only one fault is indicated at a time and faults are not queued up Refer to the troubleshooting chart Table 5 for suggestions about possible causes of the various faults Curtis PMC 1244 Manual _29 79 Curtis Speed Controller PROGRAMMING PARAMETERS E 280B E 290 E 360 T 236 T 236D WARNING The owner of this vehicle shall ensure that the service technicians are qualified properly trained and obey the safety rules and guidelines in OSHA and ANSI B56 regulations and in this manual Before installing and or programming the PMC park the vehicle on a flat level surface lift the wheels off the ground and secure with jack stands of adequate capacity Don t connect charger Programmable controllers must be programmed using the parameter settings in this service manual before connecting the motor to avoid sudden vehicle movement and accident Do not try to increase
4. output to motor field negative connection to battery positive connection to battery and to motor armature plug diode to motor armature The cables used for the battery and motor connections must be heavy enough to carry the high current required A minimum size of 25 mm 4 AWG is recommended Rubber insulated welding cable is convenient to work with because of its flexibility Connections to the controller bus bars should be made with lugs suitable for the cable used fastened by M8 5 16 bolts and nuts When tightening the bolts two opposing wrenches should be used Failure to use the double wrench technique could cause undue strain to be placed on the internal connections and could also result in cracked seals around the bus bars Curtis PMC 1204 1205 Manual 33 9 WIRING CONTROL WIRING PEDAL FUSE KEYSWITCH INTERLOCKS MICROSWITCH gt 0 O POLARITY PROTECTION POWER WIRING DIODE FUSE PRECHARGE RESISTOR 250 Q 5 W 0 5 oc 5 9 T Fig 6 Basic wiring configuration Curtis PMC 1204 1205 controller WIRING SERIES MOTORS Eigure 6 is a schematic of the configuration shown in Eigure 5 Wired this way the vehicle will plug brake if the direction is changed with the vehicle moving and the throttle applied Reversing is accomplished via two single pole double throw 2xSP
5. a Cab heater 12V 3103300001 36V 3669008 48V 4869020 L 12V Dome light 3669006 12V Fan 3669013 78 Headlamp 12V 3111250002 Headlamp 12V 3111300001 Bulb 12V 3111300002 Red Pilot light 12V 246212 Bulb 12V 246212B Spare Parts BATTERY DISCHARGE INDICATOR HOBBS This indicator monitors the residual capacity of batteries operating hours status of service down counter The residual capacity of the battery is monitored via an 8 LED bar display When the left red LED lights the batteries must be charged to avoid damage The LED display starts flashing as a pre warning signal The lower voltage limit is adjustable via potentiometer on the rear 1 84 In order to activate a new adjustment the unit has to be reset 2 35V cell reset voltage with battery remaining in vehicle 2 09V cell reset voltage after battery has been disconnected To maintain a good battery performance it is recommended to limit the discharging to 80 of the battery capacity The recommended setting for 6V batteries is F and the recommended setting for an industrial battery is K An internal relay can prevent overdischarging and damaging the batteries The relay can be wired to cut off the reverse direction or energize an N C relay and alarm Turning off and on the vehicle will override the protection for 30 sec The current status remaining operating hours before maintenance of the servi
6. POTENTIOMETER 367003 M PLASTICGEAR 5705 1 SPRING 1246208 1 LIGHT SWITCH PUSH PULL 4600 i 510 JHORNBUTION 12 BRAKELIGHTSWITCH 2607 _______ HYDRAULIC BRAKE LIGHT SWITCH 36004 513 FLASHER SWITCH 515 EMERGENCY PUSH BUTTON 3109800001 1 SE BUTTONTLABEK EOS E DC DC CONVERTER XI HOUR METER CONNECTOR ____ 2 SPEED CONTROL CONNECTOR 4 11 X4 SPEED CONTROL CONNECTOR 1 X5 ____ BATTERY CHARGER CONNECTOR 1 X x YI MAINCONTACTOR 3104236001 HRBUSSBARS 4905 1 STATICSTRAP 12450001 Consult Motrec Illustrated parts 68 Spare Parts BATTERY CONFIGURATIONS 36V CONFIGURATIONS DES BATTERIES 36V 12V Accessories Ground E 280B LIFT OUT E 320 E 330 E 360 E 300 E 302 E 322 12V Accessories Ground 12V Accessories Ground E 276 E 266 E 266 ROLL OUT 12V Accessories Ground 69 Spare Parts BUILT IN CHARGER MODEL 6430 00 CAPACITOR 2 2 97 174 ELECTRONIC 60 TIMER KIT HEATSINK ASSEMBLY WITH DIODES i ne He WHITE OR AED C DC CORDSET BLACK 2 o CR pt de TAN BLACK i WHITE Au AC CORDSET FUSE AMMETER CASE GROUND ASSEMBLY BLACK AC INPUT GROUNDED PLUG Parts list for LESTRONIC II charger MODEL 06430 TYPE 36LC25 8ET 115 VAC 60 Hz PART NO DESCR
7. 16 LEAD ASSY 484017 484017 N A N A N A N A 17 BRUSH 484009 484009 N A N A N A N A 18 LEAD AND BRUSH ASSY N A N A 2450008 2450008 3112210004 2450008 59 Spare Parts REAR SUSPENSION AND BRAKE Z0 3 1311N3431 1Q VNVO ete 12 t gt 6 7131143533310 0803 066 3 9 2023 1311 3 33310 VNVO lt 81 6 i 16 V T3LLN3U344I0 W9 60 Spare Parts REF PART NO 1 2120236001 2 481431 481430 3 2121000005 4 2121000006 5 2122236001 6 2122300001 2122300002 7 2128280001 8 2128280001 9 2129000001 10 2134000001 11 2139000002 12 2139000003 13 2182320002 14 2185280001 15 2185320001 16 2185320002 17 2192320001 18 2192320001 19 2192320001 20 2910000017 21 2910000018 22 2916000002 23 2916280002 24 2916320001 25 2916480001 26 27 28 29 30 31 2183240002 E 302 amp 348 DESCRIPTION DISC RIGHT CALIPER LEFT CALIPER BUSHING LONG BUSHING SHORT MOUNTING PLATE CALIPER LEFT CALIPER SUPPORT RIGHT CALIPER SUPPORT PADS PADS CLIPS FLEX HOXE WASHER BOLT SHACKLE LINK FORD PLATE DANA PLATE GM PLATE 4 LEAF SPRINGS 5 LEAF SPRINGS 7 LEAF SPRINGS HEAVY DUTY BOLT LONG BOLT SHORT U BOLT 1 2 NF X 2 LD U BOLT 1 2 NF X 3 1 4 LD U BOLT 1 2 NF X 2 3 4 LD U BOLT 1 2 NF X 4 LD BOLT 5 8 NC X 4 FLAT WASHER 12mm MACHINE SCREW 1 4 NC X 3 8 NYLON NUT 5 8 NC HEAVY NUT 1 2
8. 203315 CORDSET DC WITH 175 AMP YELLOW PLUG 094345 CORDSET DC WITH 350 AMP GREY PLUG 063135 PLUG ASSY DC 50 AMP ANDERSON PLUG 029575 PLUG ASSY DC 175 AMP ANDERSON PLUG 087745 FUSE ASSEMBLY 72 Spare Parts WHITE BUILT IN PORTABLE CHARGER MODEL 16360 40 AC VOLTAGE SELECTOR SWITCH SHOWN IN 100 125 WOLT POSITION PART NO 20952S 16365S 163695 209195 209485 214755 192335 020285 038945 209165 209245 209145 209265 219125 214085 053225 150295 209175 186965 140925 AC SHUNT Dc OU TP UT FUSE SCR WHITE BLACK VAA ba 5 IW 40 AMP AMMETER 10 BLACK 1 IT BREAKER 2 SCR BLACK gt ELECTROWIC 7 TIMER B 4 BLUE NATURAL BLUE BROWN TRANSFORMER BROWN L2115549 Parts list for MODEL 16360 40 TYPE 36EL20 8ET 100 125 or 200 250 VAC 50 60 Hz QTY DESCRIPTION CASE ASSEMBLY TRANSFORMER ASSEMBLY AMMETER HEATSINK ASSEMBLY W SCR SCR ASSEMBLY ELECTRONIC TIMER ASSEMBLY CONTROL CABLE ASSEMBLY BUSHING INSULATOR 7W 2 FOR DC CORDSET BUSHING INSULATOR 7K 2 FOR AC CORDSET CORDSET AC 16 3 80 MOLDED PLUG CORDSET DC 12 2 108 SB 50 PLUG GRAY CORDSET DC 12 2 108 SB 50 PLUG RED CORDSET DC 12 2 108 SB 175 PLUG RED CORDSET DC 12 2 108 SB 175 PLUG GRAY CORDSET DC 12 2 108 NO PLUG FUSEHOLDER FUSE 12 AMP MDA 12 SWITCH ASSEMBLY SHUNT ELECTRONIC CIRCUIT BREAKER 40
9. E7TW 4215 AA Pinion 2 2 4230 Washor Bolt differentlal case self locking 7116 20 x 3 4 Cone and roller differential bearing LMB03049 Cup differential bearing LM603012 Washer differential side gear thrust also serviced in kit group 4236 Use with axle 7200 724S 7300 1987 Washer differential pinion thrust also serviced in kit group 4215 Use with axle 7200 7245 7300 1987 Cup driving pinion bearing rear 8 802011 Cone and roller drive pinion rear bearing M802048 Spacer driving pinion bearing 1 5 16 10 x 15 32 long collapsible also serviced in kit group 4209 Shim pinion bearing serviced only in kit aroup 4209 Slinger pinion shaft oil Seal assy drive pinion oll ESDW 4676 Flange assy universal joint axlo end 1330 size 1987 Locknut and washer assy flange to 3 4 20 also serviced in kit group 4209 Deflector driving pinion oil sea Plastic From 1 86 1986 Spare Parts BEARING I D BEARING D SPLINE 02 L Fp TYPE LENGHT In BOLT BEARINGID In SPLINE NUMBER 28 213500 20550 F 44 5 Jj 34 28 44250 F 44 5 134 44502 F 1685 5 1565 28 362009 F 1685 5 1 568 38620014 F 18375 5 155 28 30003 F 18375 5 J 155 9 230201 Fl 266
10. MAINTENANCE amp ADJUSTMENT Curtis PMC 1204X 1205X 1209 1221 controllers and potboxes require only minimal maintenance if properly installed NoTE The controllers are sealed and thus are not field serviceable CONTROLLER Maintenance It is recommended that the following two steps be performed occasionally First remove power by disconnecting the battery and discharge the capacitors in the controller with a light bulb or a 2 10 25 W resistor connected for a few seconds across B B Follow good safety practices get the vehicle drive wheels off the ground wear safety glasses and use insulated tools see page 2 1 Make sure the electrical connections to the controller and to the motor contactors etc are tight When checking the controller bus bar connec tions for tightness use two opposing wrenches This double wrench technique will help avoid putting stress on the bus bars which could crack the seals Always use insulated wrenches 2 Inspect all seals at the front and back of the controller If necessary use a moist rag to wipe these areas clean enough so that you can see the seals Look for cracks and other signs of seal damage If the seals are intact clean the controller thoroughly either by washing it off or by wiping it clean with a moist rag Power must not be reapplied until the controller terminal area is completely dry If the seals have been damaged there are several possible causes Perhaps the doubl
11. bus bar connections for tightness use two opposing wrenches This double wrench technique will help avoid putting stress on the bus bars which could crack the seals Always use insulated wrenches 2 Inspect all seals at the front and back of the controller If necessary use a moist rag to wipe these areas clean enough so that you can see the seals Look for cracks and other signs of seal damage If the seals are intact clean the controller thoroughly either by washing it off or by wiping it clean with a moist rag Power must not be reapplied until the controller terminal area is com pletely dry If the seals have been damaged there are several possible causes Perhaps the double wrench technique was not used when the cables were installed Perhaps the vehicle s environment requires that the controller be better protected either by mount ing it in a different location or by installing a protective cover Damaged seals can lead to faulty operation We strongly recommend replacing controllers that have faulty seals Curtis PMC 1204 1205 Manual 35 22 Fig 18 Adjustment pots MAINTENANCE amp ADJUSTMENT Adjustment On some models the plug braking current and acceleration rate settings are adjustable On these adjustable controllers the adjustment pots are located as shown in Figure 18 PLUG CURRENT ADJUST ACCELERATION RATE ADJUST CW higher plug current CW faster accelerati
12. wi standard output cord Current max Environmental Enclosure 46 Bakkar To Operating 30 C to 50 C 22 F to 122 F derated Dateng CAPUT Temperature above 30 C below 0 C Reverse Polarity REEL E Storage Temperature 40 C to 70 C 40 F to 158 F AC input connector IEC320 C14 require 21 8m localized cord DC output connector OEM specific w 12AWG wire Short Circuit AC input Voltage max Vrms Regulato Frequency Hz 45 65 Current max Arms 12A 104VAC reduced 20 lt 104V EN 60335 1 2 29 ai Saas EN NEU YOU ee UL2202 EV Charging System Equipment Current nominal Arms eS h S ess MN ec S UL1564 2nd Edition Industrial Battery Charger AC Power Factor lt CSA C22 2 107 2 Battery Chargers Industrial FCC Part 15 ICES 003 Unintentional Radiators Class A L Solid YELLOW LED Ace EN55011 Radio disturbance characteristics Class PBK VELE OVI ae Limits for harmonic current emissions Flashy YELLOW EN 61000 3 3 Limits of voltage fluctuations and flicker lt 80 Charge Indicator Short Flash GREEN acd i iui Long Flash GREEN EN 61000 4 2 Electrostatic discharge immunity 100 Charge Indicator Solid GREEN So
13. AMP m N N me mm ma 73 Spare Parts DELTA Q HF CHARGER NO PART NO 1 3102240002 3102240003 3102302001 3102302002 3102480002 3102480003 3119000011 DESCRIPTION 24V CHARGER U S BATTERY 24V CHARGER LIFELINE BATTERY 36V CHARGER U S BATTERY 36V CHARGER LIFELINE BATTERY 48V CHARGER U S BATTERY 48V CHARGER LIFELINE BATTERY CONNECTOR C13 74 Spare Parts QuiQ HFIPFC Battery Charger SAVE THESE IMPORTANT AN SAFETY INSTRUCTIONS This manual contains important safety operating and installation instructions read before using charger Battery Safety Information War ning Use charger only on battery systems with an algorithm selected that is appropriate to the specific battery type Other usage may cause personal injury and damage Lead acid batteries may generate explosive hydrogen gas during normal operation Keep sparks flames and smoking materials away from batteries Provide adequate ventilation during charging Never charge a frozen battery Study all battery manufacturers specific precautions such as recommended rates of charge and removing or not removing cell caps while charging Electrical Safety information Danger Risk of electric shock Connect charger power cord to an outlet that has been properly installed and grounded in accordance with all local codes and ordinances A grounded outlet i
14. C power terminals of the forward contactor If not 0 ohm change the forward contactor If 0 ohms switch to reverse and check the resistance across the reverse power terminals If not 0 ohms change the reverse contactor TRAVEL AT REDUCED SPEED Check batteries Turn off all switches and disconnect charger Wear face shield and gloves Do not disturb any battery connection to avoid sparks Check the specific gravity of each cell Cold batteries highly discharged batteries or dead cells are the most frequent causes of reduced travel speed Check potentiometer Turn off the key switch disconnect potentiometer terminals Check the resistance between terminals Other causes of lower speed dragging brakes cold temperature higher differential oil viscosity INTERMITTENT OPERATION A bad potentiometer is the most probable cause of the following acceleration is not constant maximum speed is erratic sudden stop after a bump or shock erratic starts requiring several pedal cycles A bad F R contactor is also a probable cause of the following sudden stop after a bump or shock would not start to move at times Erratic starts could also be the cause of a misadjusted potentiometer or micro switch the pot signal must be less than 50 ohms when the micro switch turns on PMC has an HPD safety feature that prevents the vehicle from moving if the accelerator pedal is depressed before the key swi
15. NHS NHO 5 2944 8 23 tva x 5 18 n8 e nana 5 Y yana i x i 1 e i LS S 3 a i T L 28 I X i 5 2 a 215 TERRES gt 65 Spare Parts ACCESSORIES DC DC CONVERTER ACCESSOIRES CONVERTISSEUR DC DC 2HL2TL1SL1WM ACCESSORIES DC DC CONVERTER DRAWING ACC DC DC 2ZHL2TLTSLTWM VSD AUTHOR 4J GAGNONM APPROVED i sis Bin imi in kan i i i i 66 Spare Parts OPTIONS OSA 9 SH3HS Y 14 SNOLLAO DIMA SNOILdO YSLVSH SYSHSV 13 Ldarans N QSULOW BLK 104W ae LL RED 104 215 LM 94 nahi OLA 67 Spare Parts PARTS LIST _______ SERIES SPEED CONTROL 275A ____ 36700 1 A4 ____ SERIES SPEED CONTROL 350A 1205 5301 1 BI STROBELIGHT B3 REVERSE ALARM ELAB HEADLIGHT E2AB TAIL BRAKE LIGHT 2 E3 A B AMBER FRONT LIGHT gt 2 FLAC FUSE 246108K 13 GI BATTERY 02 BATTERY CHARGER FLASHERRELAY 3069004 fJ 2 SEPEXMOTOR M3 ___ SERIES MOTOR M4 WIPER MOTOR 7 CAB HEATER MICROSWITCH 36700 1
16. NUT LEFT HAND NUT RIGHT HAND BOLT LONG BOLT SHORT WHEEL NUT LOCK WASHER 7 8 JAM NUT 7 8 JAM NUT 3 4 NF SPRING PIN X 1 3 4 SET SCREW 5 16 NC CASTELLATED NUT 3 4 NF CASTELLATED NUT 1 UNEF BUSHING U BOLT GREASE FITTING BOLT 3 8 NC X 112 BOLT 5 8 NC X 4 BOLT 5 16 NC X 1 1 4 BOLT 5 16 NC X 1 BOLT 7 16 NC X 2 CARRIAGE BOLT 1 4 NC X 3 4 FLAT WASHER 1 4 FLAT WASHER 12mm FLAT WASHER 7 16 COTTER PIN 3 16 X 2 COTTER PIN 7 64 X 2 MACHINE SCREW 1 4 NC X 3 8 NYLON NUT 5 8 NC LOCK WASHER 1 4 LOCK WASHER 5 16 LOCK WASHER 3 8 LOCK WASHER 7 16 HEAVY NUT 1 2 NF NUT 14 NC NUT 3 8 NC NUT 5 16 NC Spare Parts MOTOR AND DRIVE TER RER RE M COMMON PARTS REF DESCRIPTION PART RE DESCRIPTION PART F 1 PULLEY 262424 8 MOTOR BASE FORD Contact manuf 2 V BELT 242431 BELT TENSIONER 2152002 3 PULLEY 3651001 9 SEAL 484001 4 BELT EAGLE 3651002 10 BEARING 484003 5 MOTOR BASE GM Contact manuf 11 SNAP RING 484004 6 BELT TENSIONER LONG 2452005 12 NUT WASHER PACK 484006 BELT TENSIONER SHORT 2452003 15 WAVY WASHER 484013 7 PIVOT 2452002 19 HEADBAND 484015 EE HEADBAND KIT A91 107A SPECIFIC REF DESCRIPTION A89 98 00 D00 SEPEX DC3 SEPEX DANA DRIVE MOTOR ASS 484000 204050 2450002 2450003 3112210001 3112230001 13 BRUSH SPRING 484010 484010 2450006 2450006 2450006 2450006 14 BRUSH PLATE 484011 1484011 2450007 2450007 2450007 2450007
17. height see figure below Proceed with the same verifications after the accelerator cover 1s on and then connect terminals 2 and 3 POTENTIOMETER V BRACKET AUXILIARY SWITCH IS WIRED N O WITH BLUE LEAD TO COM amp ORANGE LEAD TO N O CIRCUIT THE GREEN LEAD IS GROUNDED AUXILIARY SWITCH IS SHOWN WITH THE TREADLE IN THE UP POSITION SWITCH WILL ACTUATE AT BEGINNING OF TREADLE STROKE SYMBOLS COM N O amp N C ARE TERMINAL MARKINGS AS MARKED ON SWITCH AUXILIARY SWITCH ADJUSTING SCREW ACTUATOR PIN 13 Maintenance BELT INSTALLATION AND TENSIONING INSTALLATION Adjust the sprockets using a straight edge Slide up the edge on the larger pulley until it contacts the smaller pulley Properly adjusted pulleys will provide three points of contact Properly aligned pulleys will provide four points of contact Tighten setscrews and recheck alignment CONTACT TENSIONING Check the force required to provide a deflection of 1 8 in If the measured force 15 less than 15 158 then lengthen centre distance C P SPAN LENGTH a anak iz DEFLECTION IN C CENTER DISTANCE 14 Maintenance HYDRAULIC BRAKES DRUM BRAKES Remove brake drums and check linings wear the linings should have a thickness exceeding 1 16 1 5 mm Turn the brake adjustment to reduce the clearance between lining and drum but avoid contact or drag when the wheels are turned and the pedal is relea
18. motor speed by changing parameter settings in the speed controller it can cause accident and severe damage to the motor VOLTAGE NOMINAL BATTERY VOLTAGE IN VOLTS THRO DEADBAND Thr Neutral deadband of 5kohms pot 6 THROTTLE MAX Thr Input reg d for 100 PWM 5kohm pot 90 M4 DRIVE C L MODE 4 DRIVE CURRENT LIMIT IN AMPS 300 M1 BRAKE C L MODE 1 BRAKING CURRENT LIMIT IN AMPS 1 M4 THRTL MAP MODE 4 THROTTLE MAP AS 30 FIELD MIN MIN FIELD CURRENT IN AMPS 7 M2 BRAKE C L MODE 2 BRAKING CURRENT LIMIT IN AMPS 1 3 M3 BRAKE C L MODE BRAKING CURRENT LIMIT IN AMPS 150 FIELD MAX MAX FIELD CURRENT IN AMPS 30 M4 BRAKE C L MODE 4 BRAKING CURRENT LIMIT IN AMPS 1 FIELD MAP START Armature current at wich FIELD MAP takes effect amps 1 BRK MODE 1 THROT BRAKING AS OF BRAKE C L 50 O1 O1 O1 O1 O FIELD MAP Field Winding Current as of Armature Current M2 THRT BRK MODE 2 THROT BRAKING AS OF BRAKE C L 50 CURRENT RATIO CURRENT RATIO FACTOR OF 1 2 4 8 RESTRAINT RAMP RESTRAINT 1 TO 10 LOAD COMP LOAD COMPENSATION 0 TO 25 HIGH PEDAL DISABLE HPD TYPE STATIC RETURN TO OFF SRO TYPE THRT BRK MODE 3 THROT BRAKING AS OF BRAKE C L 50 TAPER RATE Pd brak Decrease rate when apporch Ospd M1 MAX SPEED MODE 1 MAX SPEED AS PWM OUTPUT 4 T U 2 O SEQUENCING DLY SEQUENCING DELAY IN SEC MAIN CONT INTR MAIN CONTACTOR INTERLOCK ON OR OFF MAIN OPEN DELAY MAIN CONTACTOR DROPOUT
19. respective manufacturers cover such parts Accessories light gage horn etc electrical contacts switch solenoid contactor relay diodes amp fuses belts amp pulleys filters amp spark plugs lubricants brake linings amp shoes brake drums amp discs seals seats trim and other items subject to wear are not included in this warranty nor is any item that in MOTREC sole opinion shows evidence of neglect misuse abuse collision or alteration This warranty shall not apply to normal maintenance requirements as described in the User Manual and to damages during shipment The latter is the carrier s responsibility No compensation will be allowed for delays To initiate warranty coverage on any MOTREC vehicle the Dealer must complete and return the Sales Installation Report to MOTREC within 30 days after delivery to the Original Retail Purchaser or within 90 days after the delivery date to the Dealer which ever occurs first Failure to follow these procedures will result in considering the warranty coverage effective as of the shipment date from the factory The defective vehicle must be returned at the Owner s expense to an authorised MOTREC Dealer within 30 days after failure The Owner will not be charged for parts and labour required for warranty repairs which must be performed by an authorised MOTREC Dealer only The vehicle will be returned at the owner s expense The Warranty Claim Forms must be completed and returned w
20. ventilation lors du chargement Ne jamais charger une batterie gel e Prendre connaissance des mesures de pr caution sp cifi es par le fabricant de la batterie p ex v rifier s il faut enlever les bouchons des cellules lors du chargement de la batterie et les taux de chargement recommand s Information de S curit lectrique Danger Risque de chocs lectriques Ne pas toucher les parties non isol es du connecteur de sortie ou les bornes non isol es de la batterie Toujours connecter le chargeur une prise de courant mise la terre Ne pas ouvrir ni desassembler le chargeur referer toute reparations aux personnes qualifi s Pas l usage des enfants Tel 604 327 8244 Fax 604 327 8246 The charger will automatically turn on and go through a short LED indicator self test Models 912 will flash all LED s in an up down sequence and Models 912 xx1x will alternatively flash its LED RED GREEN for two seconds If the charger is connected to battery pack a trickle current will be applied until a minimum voltage is reached If the charger is used in an off board application and the charger is waiting to be plugged into a battery pack the charging algorithm number will be displayed for 11 seconds see Check Change Charging Algorithm before ultimately displaying an under voltage fault fault disappears when plugged into battery pack Once a minimum battery voltage is detected the charger will enter the bulk c
21. when working around batteries Battery emits highly explosive gases do not produce sparks to avoid battery explosion and acid splashing Battery acid causes severe damage to eyes or skin Flush contaminated area immediately with water Use insulated tools to avoid sparks that can cause battery explosion and acid splashing Use two counteracting tools double wrench technique when disconnecting or tightening battery posts Before cleaning or replacing a battery discharge the capacitor in the controller with a 10 ohms 25 W resistor for a few seconds across B and B identify battery polarity and disconnect battery leads After cleaning the power must not be reapplied until terminal areas are thoroughly dry BATTERY LEADS AND CONNECTORS Check for loose connections damaged cables acid spill loose terminal posts quarterly BATTERY POST CORROSION If corrosion is present on battery posts remove the cable connectors use a wire brush to remove particles and then clean them with a cloth that has been moistened with ammonia ELECTROLYTE LEVEL Does not apply to sealed battery Disconnect battery connectors on roll out or lift out installations Make sure the battery roll out tray is provided with stops before rolling out Fill with distilled water Daily charged batteries normally require watering once a week Under watering leads to a shortened battery life Over watering leads to battery corrosion Be careful not to overfill
22. 006 2122300001 2122300002 2128280001 2128280001 2129000001 2134000001 2139000001 2139000002 2139000003 2180240001 2182320001 2185320001 2185488001 2192280001 2200300002 2200300003 2201320001 2201320008 2201360001 2201320009 2201360002 2205250001 2206300003 2206320001 2207000001 2207000002 2207300006 2207320001 2207320009 2208240001 2208240002 DESCRIPTION BUSHING BUSHING WITH OIL SEAL BUSHING THRUST BEARING TAPER BEARING TAPER BEARING OIL SEAL GEAR DISC RIGHT CALIPER LEFT CALIPER BUSHING LONG BUSHING SHORT LEFT CALIPER SUPPORT RIGHT CALIPER SUPPORT PADS PADS CLIP FLEX HOXE CALIPER PROTECTOR WASHER BOLT SHOCK ABSORBER SHACKLE LINK PLATE PLATE LEAF SPRINGS TUBE SHAFT AXLE BEAM LEFT SPINDLE LEFT SPINDLE BRAKES RIGHT SPINDLE RIGHR SPINDLE BRAKES KING PIN STEERING SUPPORT BOLT PATTERN 2 3 8 STEERING SUPPORT BOLT PATTERN 2 1 4 ROD END LEFT HAND ROD END RIGHT HAND REAR TIE ROD FRONT TIE ROD ARM STEERING WHEEL COVER Front axle with hydraulic disc brakes Front axle with shock absorber 58 PART NO 2219250001 2224300002 2229300001 2229300002 2229300003 2910000005 29 10000006 29 10000017 29 10000018 29 10000019 29 10000020 29 10000021 29 10000022 29 10000023 29 10000024 2910300001 2910300002 2914364001 2916000001 2930000012 DESCRIPTION SPACER HUB DUST CAP OIL SEAL SPINDLE WASHER
23. 075 242076 3620006 242077 242078 242079 242080 2420019 481432 2128280001 481434 481442 481440 481441 3614002 3614003 2192280001 2192320001 2162320002 2183240002 2916320001 3640004 2185320002 3640005 DESCRIPTION WASHER GEAR KIT WASHER GEAR KIT SCREW SHAFT WITH 4 56 GEAR RATIO OTHERS GEAR RATIO CAP BOLT DRAIN PLUG DIFFERENTIAL COVER BOLT BRAKE HOSE FOR DISC BRAKE BRAKE PADS BOLT LONG BOLT SHORT HYDRAULIC BOLT WASHER BUSHING LONG BUSHING SHORT 1200 165 CAP SPRING E 348 3000 Ibs CAP SPRING E 480 SHACKLE BUSHING GM U BOLT FORD U BOLT BOLT 5 8 NC X 3 1 LOCK NUT 5 8 NC GM PLATE FORD PLATE Spare Parts FORD F 150 DIFFERENTIAL OLD 242063 BREATHER 242054 BOLT AA 3620007 O HOUSING BEARING SEAL RING KIT 3620020 CONE amp CUP 84 CN 4216 385696 S 4230 LOCKTITE RTV 3620020 de A 4 373098 5 a WS Hi 4143 G 359475 S NN 116 4669 305105 5 9 27 amp 4614 3620023 2 75 O D OIL SEAL a 3620024 3 0 O D OIL SEAL LOCKTITE RTV 3621001 PULLEY W80 8 O D 3621002 PULLEY W90 9 3620011 GEAR KIT 3620022 CONE amp CUP 3620022 CONE amp CUP BREATHER 2320004 MOUNTING PLATE 3 242063 NEW A BOLT 1 2 NF X 3 S 2320006 SPACER 4420003 RETAINING RING j HOUSING 4420005 RETAINER Ra 242054 BOLT
24. 30 AMP 16369S AMMETER 0 30 AMP 063575 ELECTRONIC TIMER ASSEMBLY RELAY 044845 04484D RELAY TIMER KIT 36 VDC 020285 BUSHING 7W 2 INSULATOR FOR DC CORD 119235 CORDSET AC 095225 CORDSET 2 10 AWG 160 NO PLUG 085125 CORDSET DC NO PLUG 080205 CORDSET DC WITH LESTER PLUG 127815 CORDSET DC WITH GREY LESTER PLUG 086075 CORDSET DC WITH 50 AMP ANDERSON PLUG 082245 CORDSET DC WITH 175 AMP ANDERSON PLUG 105365 CORDSET DC WITH 130 50 AMP amp EZ GO PLUG 083135 PLUG ASSY DC 50 AMP ANDERSON PLUG 029575 PLUG ASSY 175 AMP ANDERSON PLUG For use with chargers built before Dec 90 For use with chargers built after Dec 90 71 Spare Parts BUILT IN PORTABLE 40A CHARGER ELECTRONICTIMER TRANSFORMER rad or white gt TQ BATTERIES FUSE ASSEMBLY black AMMETER CAPACITOR Parts list for LESTRONIC II charger MODEL 09475 TYPE 36LC40 8ET 115 VAC 60 Hz PART NO DESCRIPTION 094775 CASE ASSEMBLY 09476S TRANSFORMER ASSEMBLY 090415 HEATSINK ASSEMBLY WITH DIODES 088495 DIODE ASSEMBLY 16823S AMMETER 096855 ELECTRONIC TIMER ASSEMBLY 023905 CAPACITOR 6 0 MFD 660 VAC 020085 BUSHING 8P 2 INSULATOR FOR DC CORD 020285 BUSHING 7W 2 INSULATOR FOR AC CORD 025065 CORDSET AC 065115 CORDSET DC NO PLUG 187715 CORDSET DC WITH MOLDED PLUG GREY 080675 CORDSET DC WITH LESTER PLUG 080695 CORDSET DC WITH 50 AMP GREY PLUG 083295 CORDSET DC WITH 175 AMP GREY PLUG
25. 44 Manual 26 8 8 DIAGNOSTICS amp TROUBLESHOOTING Curtis PMC 1244 Manual DIAGNOSTICS AND TROUBLESHOOTING The 1244 controller provides diagnostics information to assist technicians in troubleshooting drive system problems The diagnostics information can be obtained by observing the appropriate display on the handheld programmer the fault codes issued by the Status LED or the fault display driven by the controller s Fault 1 and Fault 2 outputs Refer to the troubleshooting chart Table 5 for suggestions covering a wide range of possible faults PROGRAMMER DIAGNOSTICS The programmer presents complete diagnostic information in plain language Faults are displayed in the Diagnostic Menu see column 2 in the troubleshooting chart and the status of the controller inputs outputs is displayed in the Test Menu Accessing the Diagnostic History Menu provides a list of the faults that have occurred since the diagnostic history file was last cleared Checking and clearing the diagnostic history file is recommended each time the vehicle is brought in for maintenance The following 4 step process is recommended for diagnosing and trouble shooting an inoperative vehicle 1 visually inspect the vehicle for obvious problems 2 diagnose the problem using the programmer 3 test the circuitry with the programmer and 4 correct the problem Repeat the last three steps as necessary until the vehicle is operational Example A vehic
26. 5 LI74 2135002 FE 26 5 14 28 21050 Fl 1935 5 L7Z4 44508 Fl 58535 5 174 4504 Fl 58535 5 174 8 443505 FI 1488 5 17464 4506 Fl 1488 5 74 28 4507 HE 535 5 174 4506 Fl 535 5 174 4507 Fl 148 4 134 6 7502 Fl 258 4 324 6 263501 1688 283501 __ 5 17 4 663501 1415 4 195 6 2952 145 24 195 6 202 1685 24 19 J 6 92952 145 4 35434 6 2004 145 24 1354 26 2004 226 5 1 4 26 035 7 5 134 6 2507 142 4 134 38020004 11422 5 234 6 36206 2 2 5 1354 4835002 14 5 134 6 483505 DI 45 5 8 25202 ___ D 145 5 8 27 35002 D 145 5 8 O12SRI241 D2 585 5 012581242 gt 735 5 8 24 012581303 __02 44500 5 E188 2 02503504 Oil Oa a Oi Oa Oa CA Oi i GA 54 Spare Parts HYDRAULIC DRUM BRAKES REF PART NO DESCRIPTION 1 362841 PLATE CYLINDER 2 362842 BRAKE SHOE 4 362844 S
27. 52 Spare Parts QTY am 10 PART NUMBER 373098 S 100 42 8 2 D9AZ D9AZ DSAZ 09 2 09 2 D9AZ D9AZ D9AZ D9AZ D9AZ D9AZ D9AZ D9AZ D9AZ D9AZ D9AZ D9AZ 9 2 D9AZ D9AZ D9AZ D8AZ D9AZ D9AZ D9AZ D8AZ D9AZ 0942 D9AZ E7TZ C7AZ D8BZ E6TZ 6 2 E5TZ B7A B7A 4033 4036 4067 4067 A 4067 B 4067 0 4067 D 4067 E 4067 4067 6 4067 H 4067 J 4067 K 4067 L 4067 M 4067 N 4067 P 4067 8 4067 5 4067 T 4067 1 4067 4067 W 4067 X 4067 Y 4067 Z 4087 4067 4067 4067 0 4067 AE 4067 AF 4236 4N237 A 4241 A 4 332 4346 4346 4346 4246 4616 4621 DESCRIPTION Plug housing 1 2 14 Cover assy housing also serviced in assy group 4010 Gasket cover to housing use DBAZ 19562 8 Shim differential bearing adjustment 241 thick 243 thick 245 thick 247 thick 248 thick 251 thick 253 thick 255 thick 257 thick 259 thick 261 thick 263 thick 265 thick 267 thick 269 thick 271 thick 273 thick 275 thick 277 thick 279 thick 281 thick 283 thick 285 thick 287 thick 289 thick 291 thick 293 thick 205 thick 297 thick Gear kit differential side usa with axle 87200 7245 7200 1987 Consists of 2 2 4228 Washer 2 E7TW 4236 Gear U washer axle shaft retaining Pin differential pi
28. 6958 Rev B January 2001 24 1244 Manual p n 16958 Rev B January 2001 2001 CURTIS INSTRUMENTS INC CURTIS INSTRUMENTS INC 200 KISCO AVENUE MOUNT KISCO NEW YORK 10549 USA 914 666 2971 Fax 914 666 2188 CURTIS PMC 235 EAST AIRWAY BOULEVARD LIVERMORE CALIFORNIA 94550 USA 925 961 1088 rax 925 961 1099 ADDITIONAL OFFICES located in Bulgaria China England France Germany India Italy Japan Netherlands Puerto Rico Russia Sweden and Switzerland www curtisinst com 25 2 INSTALLATION amp WIRING Controller WIRING Standard Configuration Figure 3 shows the typical wiring configuration for most applications The interlock switch is typically a seat switch tiller switch or foot switch Standard Power Wiring Motor armature winding is straightforward with the armature s Al connection going to the controller s B bus bar and the armature s A2 connection going to the controller s M bus bar The motor s field connections F1 and F2 to the controller are less obvious The direction of vehicle travel with the forward direction selected will depend on MAIN CONTACTOR FORWARD REVERSE 5 0 THROTTLE TYPICAL MODE SELECT 2 MODE SELECT 1 INTERLOCK KEYSWITCH MAIN CONTACTOR POLARITY PROTECTION DIODE CONTROL FUSE B Fig 3 Standard wiring configuration Curtis PMC 1244 controller Curtis PMC 12
29. DELAY IN SEC AUK CHECK AUXILIARY COIL OPEN CHECK ON OR OFF EM BRAKE DELAY ELECTROMAGNETIC BRAKE DELAY IN SEC EM BRAKE CHECK ELECTROMAG BRAKE OPEN CHECK ON OR OFF 32 0 M2 MAX SPEED MODE 2 MAX SPEED AS PWM OUTPUT M3 MAX SPEED MODE 3 MAX SPEED AS PWM OUTPUT O O O O O M4 MAX SPEED MODE 4 MAX SPEED AS PWM OUTPUT M1 CREEP SPEED MODE 1 CREEP SPEED AS PWM OUTPUT M2 CREEP SPEED MODE 2 CREEP SPEED AS PWM OUTPUT M3 CREEP SPEED MODE 3 CREEP SPEED AS PWM OUTPUT M4 CREEP SPEED MODE 4 CREEP SPEED AS PWM OUTPUT REGEN SPEED Min speed for regen braking as of vehicle speed CTRL MODE CONTROL MODE THROTTLE TYPE THROTTLE TYPE 30 Curtis Speed Controller CURTIS PMC MOTOR CONTROLLER ee MANUAL 235 CURTIS 217717 1204 5 MOTOR CONTROLLERS 1999 CURTIS INSTRUMENTS INC DESIGN OF CURTIS 1200 SERIES CONTROLLERS PROTECTED BY U S PATENT NO 4626750 1204 1205 Manual p n 98690 Rev B May 1999 WIRING WIRING CONNECTIONS Low Current Three 1 4 push on terminals are provided KSI i throttle for the low current connections to the KSI inputs and throttle inputs For the control wiring 0 75 mm 18 AWG vinyl insulated stranded wire is rec ommended CONNECTIONS High Current Four tin plated solid copper bus bars are provided for the high current connections to the battery and motor
30. DT contactors Coil suppression diodes should be used on the main and forward reverse contactors KSI Wiring The keyswitch input KSI circuit includes input from the keyswitch and from the various interlocks The controller KSI is used to turn the controller on and off KSI is turned on by connecting it to battery B Any positive voltage greater than about 8 volts will turn on the controller but usually the full vehicle battery voltage is used KSI draws only a very small current a few mA In its simplest form KSI is operated by a keyswitch that turns the vehicle off and prevents unauthorized use The keyswitch should also Curtis PMC 1204 1205 Manual 34 10 MAINTENANCE amp ADJUSTMENT MAINTENANCE amp ADJUSTMENT Curtis 1204 1205 controllers and potboxes require only minimal main tenance if properly installed NoTE The controllers are sealed and thus are not field serviceable CONTROLLER Maintenance It is recommended that the following two steps be performed occasion ally First remove power by disconnecting the battery and discharge the capacitors in the controller with a light bulb or a 2 10 Q 25 W resistor connected for a few seconds across B B Follow good safety practices get the vehicle drive wheels off the ground wear safety glasses and use insulated tools see page 2 1 Make sure the electrical connections to the controller and to the motor contactors etc are tight When checking the controller
31. E MAIN PRECHARGE RESISTOR 2500 5 W C N T 7 2 A lt lt POTBOX gt E 51 52 L Z KSI F R cont out 1 Bypass cont output Emergency reverse E EWD input NN 3 REV input 1A BYPASS See Figure 10 for emergency reverse Fig 8 Basic wiring configuration Curtis 1204X 1205X 1209 1221 controllers contactor and the forward reverse contactors This will act as a safety feature by removing power from the motor control system when the keyswitch is off Interlocks seat switches battery charger interlocks etc should be wired in series so that they turn off the controller KSI and the contactors An SRO interlock a seat switch for example must be wired in order to implement the optional SRO feature Forward Reverse Wiring The forward reverse wiring schemes described here all assume the power wiring shown by the heavy lines in Figure 8 Some vehicles especially those previously using older resistor type controllers may reverse the motor armature rather than the field winding Be careful if you are replacing this type of controller When using the Curtis PMC controller it is essential that the field be reversed and that the armature be connected directly to the controller s B and A2 terminals because the plug diode inside is connected to these terminals Curtis PMC 1204X 1205X 1209 1221 Manual 43 13 MAINTENANCE amp ADJUSTMENT
32. IPTION 073355 CASE ASSEMBLY 186875 CASE ASSEMBLY WITH NO HANDLE 096915 TRANSFORMER ASSEMBLY 023905 CAPACITOR 6 0 MFD 660 VAC 163545 HEATSINK ASSEMBLY WITH DIODES 08776S FUSE ASSEMBLY 041275 AMMETER 0 30 AMP 096855 ELECTRONIC TIMER ASSEMBLY RELAY 044845 044845 RELAY TIMER KIT 36 VDC 020285 BUSHING 7W 2 INSULATOR FOR DC CORD 025065 CORDSET AC 14 3 72 113275 CORDSET AC 14 3 18 138955 CORDSET AC 14 3 114 085125 CORDSET DC NO PLUG 12 2 108 127815 CORDSET DC GREY RUBBER PLUG 12 2 108 095225 CORDSET DC NO PLUG 2 10 AWG 160 080205 CORDSET DC WITH LESTER PLUG 086075 CORDSET DC WITH 50 AMP ANDERSON PLUG 062245 CORDSET DC WITH 175 AMP ANDERSON PLUG 113285 CORDSET DC WITH RING TERMINALS 083135 PLUG ASSY DC 50 AMP ANDERSON PLUG 029575 PLUG ASSY DC 175 AMP ANDERSON PLUG 043285 RECEPTACLE MOTOR BASE 125 15 70 Spare Parts PORTABLE CHARGER MODEL 07710 02 GROUNDED CAPACITOR HEATSINK ASSEMBLY WITH DIODES aja 2 ELECTRONIC TAN TIMER KIT DC CORDSET WHITE OR RED BLACK lt gt ates q BATTERIES EE BLACK 28 CORSET FUSE AMMETER GROUND ASSEMBLY Parts list for LESTRONIC II charger MODEL 07710 36LC25 SET 115 VAC 60 Hz PART NO DESCRIPTION 073775 CASE ASSEMBLY 078495 TRANSFORMER ASSEMBLY 023905 CAPACITOR 6 0 660 VAC 163545 HEATSINK ASSEMBLY WITH DIODES 08776S FUSE ASSEMBLY 041275 AMMETER 0
33. LY MOTOR AND DRIVE REAR SUSPENSION AND BRAKE ELECTRICAL DIAGRAM SEPEX MAIN CIRCUIT ELECTRICAL DIAGRAM SERIES MAIN CIRCUIT ELECTRICAL DIAGRAM SERIES MAIN CIRCUIT ACCESSORIES NO DC DC CONVERTER ACCESSORIES DC DC CONVERTER O 1 13 14 15 16 17 19 20 23 26 27 26 29 30 31 33 35 37 39 41 44 47 48 49 50 52 55 56 57 59 60 62 63 64 65 66 Table of contents OPTIONS BATTERY CONFIGURATIONS 36V BUILT IN CHARGER MODEL 6430 00 PORTABLE CHARGER MODEL 07710 02 BUILT IN PORTABLE 40A CHARGER BUILT IN PORTABLE CHARGER MODEL 16360 40 DELTA Q HF CHARGER MOTREC ILLUSTRATED ACCESSORIES BATTERY DISCHARGE INDICATOR HOBBS ADDENDUM CURTIS FOOT PEDAL 67 69 70 71 22 73 74 77 79 80 81 Instructions INSTRUCTIONS Instructions SAFETY WARNINGS FOR OPERATORS e FAILURE TO OBEY THE FOLLOWING SAFETY RULES MAIN RESULT IN SEVERE INJURY e 15 the responsibility of the owner of this vehicle to train operators to ensure that they understand the operating characteristics of this vehicle including training in vehicle stability and obey the following safety rules and guidelines Owner shall comply with OSHA and ASME ANSI B56 8 amp B56 9 regulations for vehicle use safety rules operator training and certification Do not drive this vehicle unless you are a qualified operator e Do not drive this vehicle under the influence of drugs or alcohol e Do not drive this vehicle on public
34. NF BUSHING E 320 322 330 360 amp 480 STANDARD E 500 amp 660 AND OPTIONAL E 320 322 330 360 amp 480 61 Spare Parts ELECTRICAL DIAGRAM SEPEX MAIN CIRCUIT 7 DIAGRAMME ELECTRIQUE CIRCUIT PRINCIPAL SEPEX OSA H390HVH2 trek X34335 62 Spare Parts ELECTRICAL DIAGRAM SERIES MAIN CIRCUIT DIAGRAMME LECTRIQUE CIRCUIT PRINCIPAL SERIES 2006 04 11 SERIES CHARGER MAIN CIRCUIT SERIES 01 DATE SERIES CHARGER VSD MOTREC inc AUTHOR J GAGNON APPROVED DRAWING 8 TITLE VERSION 63 Spare Parts ELECTRICAL DIAGRAM SERIES MAIN CIRCUIT DIAGRAMME LECTRIQUE CIRCUIT PRINCIPAL SERIES x 9 c lt MAIN CIRCUIT SERIES 5 F SERIES 1205X WHT M3 RED 2 L __ 432 4 2 d A1 Y2 A Y2 B WHT BLK ACCESSORIES DC DC CONVERTER ACCESSOIRES SANS CONVERTISSEUR DC DC Spare Parts OSA WALTSLETLETHE 90 90 ON 29 if NONSY NOISHSA ON fN uo Buipuadap Jo 941 WML ISL ILETH2 99v u8xXe jou si uondo 2 Losrans 90 90 304 eAgisod jas Aayeq 1500 ajeipauua u UE pajoeuuoo si punoJD sauossa2oy mim m mim mimimim m j
35. OR LEAK E STEERING ASSEMBLY as instructed BRAKE MECHANICAL LINKAGES for wear amp play BRAKE LININGS FOR WEAR 1 16 1 5 mm minimum lining thickness LUBRICATE brake pedal pivots steering column ball joints and kingpins OIL SAE 30 LEVEL IN DIFFERENTIAL Before adding oil check oil seals for leaks FRONT WHEEL BEARINGS PLAY TIGHTEN NUTS BOLTS electric terminals drive steering brakes suspension body REPLACE DIFFERENTIAL OIL SAE 30 CLEAN AND RE PACK FRONT HUBS SERVICE DIFFERENTIAL replace the three oil seals wheel bearings oil SAE 30 212 Maintenance ACCELERATOR GEAR Remove the cover Backlash between gears must be reduced to a minimum by sliding holder use locktite 262 to lock the three screws When the plastic gear is fully depressed a small backlash must remain between the gears When the plastic gear is released its rear portion must not exceed the pedal case MICRO SWITCH The micro switch must deactivate the on off solenoid when the accelerator is released turn the adjusting screw shown on figure below to adjust the micro switch height POT Remove the terminals 2 and 3 on PMC to measure resistance signal When the micro switch is activated the signal must be less than 50 ohms When the front portion of the pedal is fully depressed the signal must be more than 4600 ohms To modify the resistance turn the adjusting screw to change the micro switch
36. PRING 5 362845 SPRING 6 362846 SPRING 7 362847 SPRING 8 362848 FITTING 9 362849 BLEEDER 10 362850 PISTON 13 362853 ADJUSTER 14 362855 BOLT GRADE 8 15 3612001 LEFT LEVER 3612002 RIGHT LEVER 55 Spare Parts REF PART NO N D 10 11 12 13 2910000015 2930000012 2131100002 2131360002 2131360012 2133280001 2132320001 2125000001 version BRAKE CONTROLS DESCRIPTION Nut 1 4 20UNC Yoke Lock washer 4 Lubrication fitting Rubber pad Lever Lever Push rod Master cylinder Nut 3 8 16UNF Pivot Boot included with 2125000001 Master cylinder Clevis pin 3 8 x 1 3 32 Cotter pin 3 32 x 1 QTY REF PARTNO 14 2190000003 15 2910000013 16 17 18 19 2139240002 20 2129000003 21 2129000001 22 2921000001 23 2127000006 24 2127000001 25 2191240002 Ne mm ma ma ma 56 DESCRIPTION Spring Extention Yoke Cotter pin 3 32 x 1 Flat washer 5 16 Clevis pin 5 16 x 1 1 2 Handbrake lever Handbrake cable Clip Cable stop Handbrake band side cable Handbrake band Spring compression OTY N Spare Parts FRONT ASSEMBLY 57 Spare Parts REF 32 33 34 36 37 39 40 PART 2100300002 2100300001 2100300003 2103250001 2103300001 2103300002 2104300004 2117250001 2120236001 481431 481430 2121000005 2121000
37. Tail Brake light Housing 3069012R Bulb 12V 3117240001 Back up lamp Grommet 12V 24V 3269001 3669012 3669012A Clear lamp 12V Bulb 12V 3069012 1269008 Pedestral head lamp 12V 2569001 Bulb 12V 2569001B Bulb 24V 4469001 Headlight Left Right Bulb H L Bulb Turn Bulb Mark 3111480003 3111480004 3111480006 3111480008 3111480007 Headlight Left 3111480003 Right 3111480004 Bulb H L 3117480001 Bulb Turn 3117480003 Bulb Mark 3117480002 Turn signal switch 246050 Multi LED Red Tail Brake Light 3111000006 Grommet 3111000008 Plug 3119000009 Multi LED Back up Light 3111000007 Grommet 3111000008 Plug 3119000009 Horn 12V 246003 24V 246013 77 Horn button VIP 2330014 Horn button column mount 246210 Horn button dash mount 266210 Horn button 3109250001 Limit switch 3030015 Back up alarm 12 48V 72 80V 3100000001 3105720001 Spare Parts Analog Voltmeter 12V 3069007 24V 2469002 36 48V 3669002 HOBBS Gauge 24V 2469026 36V 3069038 48V 4869037 DC DC converter 10A 12 48V 3069019 7 DC DC Converter 25 12 48V 72 80V 3124000002 3124880001 Wiper motor 12V 24V 3113000001 486211 Wiper arm 2800000001 Wiper blade 14 Blade 18 Blade 2800000002 2800000003 Em Pantograph wiper arm 246233A Pantograph wiper blade 246233
38. actor or solenoid Check voltage across power terminals if not B check circuit breaker or replace the solenoid Turn to on the key switch and activate the seat switch Check voltage across the coil terminals if not B check wiring and interlock switches Check resistance across power terminals if not 0 ohms replace the solenoid Check circuit breaker and SEPEX DIODE Before replacing the circuit breaker check for shorts in the power circuit and check the SEPEX diode in the power circuit using a diode tester If no such instrument is at hand use an ohmmeter the reading should be weak in one direction and strong in the other way Check the resistance across the circuit breaker If not 0 ohms replace the circuit breaker Check PMC First disconnect battery B and B then PMC B and M Check the internal diode between B and M terminals using a diode tester If no such instrument is at hand use an ohmmeter the reading should be weak in one direction and strong in the other way If the internal diode is defective the PMC must be replaced Check the Motor First disconnect battery B and B disconnect power terminals and check the motor armature and field for opens 22 Curtis Speed Controller CURTIS SPEED CONTROLLER 23 MANUAL CURTIS 211 1244 MultiMode MOTOR CONTROLLER 2001 CURTIS INSTRUMENTS INC DESIGN OF CURTIS PMC 1200 SERIES CONTROLLERS PROTECTED BY U S PATENT NO 4626750 1244 Manual p n 1
39. any cell to avoid electrolyte to be forced out while charging Fill each cell to plate level with distillated or de ionized water before battery charging When the battery is charged the fluid expands and can seep out if overfilled Refill each cell after full charge when the fluid has expanded to its maximum level Reinstall battery caps before charging 17 Maintenance BATTERY MOUNTING A loose battery increases damaging effects of vibrations and is more prone to short out BATTERY DISCHARGE LIMIT Discharging below a 20 state of charge cuts down the battery life and the number of cycles available At 20 state of charge specific gravity of 6V battery should be 1180 and 1220 for industrial battery CHARGING AREA Always charge battery in a well ventilated area set for and approved for charging Never leave a charger connected for more than 20 hours FREQUENCY OF CHARGE When a battery is discharged to its 20 state of charge it is best to charge immediately Batteries require a low current equalization charge min 4 hours at least every week to equalize battery cells improve battery performance and life in number of cycles Never leave a charger connected for more than 20 hours STORAGE Keep the battery from getting cold it would loose its capacity Let the battery warm up before charging Charge batteries in stored vehicles every month DEFECTIVE BATTERY Check specific g
40. ar F R SWITCH Three positions with neutral at center Depress the front part of the rocker switch for forward direction Depress the rear part of the rocker switch for reverse direction Always set switch to neutral turn off all switches set the parking brake remove the key before leaving the vehicle ACCELERATOR PEDAL It is designed for right foot operation only and controls the speed of the vehicle FOOT BRAKE PEDAL It is designed for right foot operation only The brake force is proportional to the pressure on the pedal PARKING BRAKE Pull handbrake lever to apply Never park the vehicle on an incline Always turn off all switches set the F R selector to neutral set the parking brake remove the key before leaving the vehicle 7 Maintenance MAINTENANCE Maintenance SAFETY WARNINGS FOR SERVICE TECHNICIANS FAILURE TO OBEY THE FOLLOWING SAFETY RULES MAIN RESULT IN SEVERE INJURY Owner shall comply with OSHA and ASME ANSI B56 8 amp B56 9 regulations for vehicle maintenance Only qualified and authorized personnel shall be permitted to maintain repair adjust and inspect carriers vehicles tractors and batteries Before any maintenance work park the vehicle on flat level surface turn off all switches remove key lift wheels off the ground and secure with jack stands of adequate capacity Don t connect charger Keep clear from moving parts such as tires sheaves and motor Follow the maintenance instr
41. cause severe burns on skin or eyes When working around batteries wear acid proof protective equipment face shield and gloves Use electrically insulated tools to avoid sparks that can cause battery explosion Before any maintenance work park the vehicle on a flat level surface turn off all switches remove the key lift the wheels off the ground and secure with jack stands of adequate capacity identify and disconnect battery leads Don t connect the charger MECHANICAL DAMAGE OILLEAKS X T REVERSE ALARM DEADMAN SWITCH X STATIC STRAP min 27 contact with ground X TIRE PRESSURE pressure rating on tire X p CHECK FILL BATTERIES add distilled water to cover plates Fill to recommended level after batteries have been fully charged WARNING DECALS amp MARKINGS I X SEADCONOLBOX X L SEALED CONTROL BOX MASTER CYLINDER FLUID DOT3 X BRAKE PEDAL TRAVEL 2 50 mm maximum travel STEERING FOR PLAY PARKING BRAKE LEVER requires 10 Ibs 5 kg force to apply BELTS AND PULLEYS 10 Ibs 5kg force for 1 8 3mm deflexion pulleys alignment see procedure WASH BATTERY TOP WITH WATER MOTOR BRUSHES FOR WEAR ACCELERATOR ADJUSTMENT 1 8 3 mm travel to activate micro switch 0 to 50 ohms when micro switch activated 4500 to 5500 ohms with pedal down HYDR BRAKE LINES F
42. ce down counter is indicated for a period of 5 seconds after the key switch 1s turned on When it is down to 0 the display flashes After the maintenance reset the counter depress the button R on the rear The service counter is factory programmable only 24V UNIT 2469026 36V UNIT 3069038 48V UNIT 4869037 2 Orange key switch 3 Relay 4 Relay 5 Black battery 6 Blue hour counter 8 White battery 79 Addendum ADDENDUM 30 Addendum CURTIS FOOT PEDAL BLUE KEY SWITCH GREEN HOUR METER BLACK POTENTIOMETER WHITE POTENTIOMETER NAK ku RESP CLAUDE L MODEL E PART NO 3062001C 367008 2262004C 2262001C 2262003C 3662002 3 DESCRIPTION ACCELERATOR CURTIS POTENTIOMETER SPRING MICRO SWITCH LEVER CABLE PROTECTOR NO 321A320001 SER 1018799 81 TO A 320 360 480 500 1019973
43. d this manual carefully If you have questions please contact the Curtis office nearest you Working on electric vehicles is potentially dangerous You should protect yourself against runaways high current arcs and outgassing from lead acid batteries RUNAWAYS Some fault conditions could cause the vehicle to run out of control Jack up the vehicle and get the drive wheels off the ground before attempting these procedures or any other work on the motor control circuitry HIGH CURRENT ARCS Electric vehicle batteries can supply very high power and arcs can occur if they are short circuited Always open the battery circuit before working on the motor control circuit Wear safety glasses and use properly insulated tools to prevent shorts LEAD ACID BATTERIES Charging or discharging generates hydrogen gas which can build up in and around the batteries Follow the battery manufacturer s safety recommendations Wear safety glasses Curtis PMC 1204X 1205X 1209 1221 Manual 40 2 WIRING WIRING CONNECTIONS Low Current Two 1 4 push on terminals are provided for the throttle inputs If your controller has a voltage throttle input there will be only one throttle terminal A 6 pin low power connector molded into the right side of the controller face provides the low power logic control connections KSI input forward reverse contactor output bypass contactor output optional emergency reverse optional and for
44. defective THROTTLE FAULT 1 wiper signal out of range Throttle input wire open Throttle input wire shorted to B or B THROTTLE FAULT 2 pot low fault Throttle pot defective 2 Wrong throttle type selected SRO SRO fault Improper sequence of KSI interlock and direction inputs Wrong SRO type selected Interlock or direction switch circuit open Sequencing delay too short HPD fault Improper seq of direction and throttle inputs Wrong HPD type selected Misadjusted throttle pot Sequencing delay too short BB WIRING CHECK emergency reverse wiring fault Emergency reverse wire open Emergency reverse check wire open CONT DRVR OC cont driver output overcurrent Contactor coil shorted MAIN CONT WELDED welded main contactor Main contactor stuck closed Main contactor driver shorted HARGE FAULT internal voltage too low at startup Controller defective 2 External short or leakage path to B on external B connection MISSING CONTACTOR missing contactor Any contactor coil open or not connected MAIN CONT DNC main contactor did not close Main contactor missing or wire to coil open LOW BATTERY VOLTAGE low battery voltage Battery voltage lt undervoltage cutback limit Corroded battery terminal Loose battery or controller terminal OVERVOLTAGE overvoltage Bat
45. e wrench technique was not used when the cables were installed Perhaps the vehicle s environment requires that the controller be better protected either by mounting it in a different location or by installing a protective cover Damaged seals can lead to faulty operation We strongly recom mend replacing controllers that have faulty seals Adjustment Some controllers allow adjustment of the plug braking current current limit and acceleration rate settings The adjustment pots on these models are located as shown in Figure 16 Curtis PMC 1204X 1205X 1209 1221 Manual 44 22 MAINTENANCE amp ADJUSTMENT Fig 16 Adjustment pots CURRENT LIMIT ADJUST CCW lower current limit PLUG CURRENT ADJUST ACCELERATION RATE ADJUST CW higher plug current CW faster acceleration Use the following adjustment procedure The keyswitch should be off during adjustment 1 Remove the socket head screw 1 8 Allen for the adjustment you want to make 2 Adjust the internal potentiometer using a small insulated screwdriver available from Curtis 3 Replace the socket head screw and nylon seal washer To prevent stripping do not over tighten POTBOX Maintenance Potbox maintenance is similar to controller maintenance inspect for integrity of connections and mounting and clean with a moist rag as required Adjustment Curt
46. erly installed Keep cables and wires clear from mechanical and rubbing action Make sure that cable insulation is free from cutting or visible damage Make sure that EE Rated cable protectors are properly installed Before replacing a fuse or circuit breaker identify the cause of failure and repair Programmable controllers must be programmed using the parameter settings in this service manual before connecting the motor to avoid sudden vehicle movement and accident Maintenance Do not try to increase motor speed by changing parameter settings in the speed controller it can cause accident and severe damage to the motor SEPEX speed controls are protected by a diode in the power circuit to filter inductive loads in the event of a sudden power interrupt Some speed controllers require a diode to filter inductive loads on the KSI input Removing the diodes will cause the speed control failure Before resuming maintenance operations inspect safety warnings stickers and replace any if damage is found and part of the text can t be read 10 Maintenance DECALS AND LABELS CAUTION The images included in this section depict the decals markings installed on the vehicle It is of the utmost importance that theses decals markings remain unaltered and readable Else the sticker or the part baring the marking has to be replaced Dashboard security warning label Operation of this vehicle is restricted to authorized person
47. ermitted to maintain repair adjust and inspect the vehicle MOTREC prohibits and disclaims responsibility for any vehicle modification altering the weight distribution and stability increasing the speed or affecting the safety of the vehicle Such modifications can cause serious personal injury or property damage for which MOTREC disclaims any responsibility For Owners that are located outside North America the warranty period starts the date of shipment from the factory and the defective parts must be returned at the Owner s expense to MOTREC prior to warranty repair 06 12 2006 Table of contents TABLE OF CONTENTS INSTRUCTIONS SAFETY WARNINGS FOR OPERATORS OPERATING INSTRUCTIONS MAINTENANCE SAFETY WARNINGS FOR SERVICE TECHNICIANS DECALS AND LABELS PERIODIC MAINTENANCE CHECKLIST ACCELERATOR BELT INSTALLATION AND TENSIONING HYDRAULIC BRAKES FRONT AXLE AND STEERING BATTERY MAINTENANCE BATTERY CHARGER ELECTRICAL TROUBLESHOOTING CURTIS SPEED CONTROLLER WIRING STANDARD CONFIGURATION DIAGNOSTICS AND TROUBLESHOOTING TROUBLESHOOTING CHART LED DIAGNOSTICS PROGRAMMING PARAMETERS E 280B E 290 E 360 T 236 T 236D CURTIS PMC MOTOR CONTROLLER WIRING STANDARD CONFIGURATION MAINTENANCE AND ADJUSTMENT CURTIS PMC MOTOR CONTROLLER OVERVIEW WIRING STANDARD CONFIGURATION MAINTENANCE AND ADJUSTMENT SPARE PARTS BODY CAB DIFFERENTIAL AND REAR SUSPENSION FORD F 150 DIFFERENTIAL HYDRAULIC DRUM BRAKES BRAKE CONTROLS FRONT ASSEMB
48. g characteristics of this vehicle and obeys the safety instructions ANSI B56 Do not drive this vehicle unless you are a qualified operator BEFORE USING VEHICLE Before turning on key switch set to neutral check for any visible damage check brake pedal BATTERIES Never open the battery compartment unless you have received proper training for battery maintenance Batteries emit explosive hydrogen gas that can be ignited by a spark or loose terminal Battery acid causes severe damage to eyes or skin Flush the contaminated area immediately with water BATTERY CHARGER Park the vehicle in a well ventilated area for battery charging Most battery chargers come with an electronic control that starts when the charger is plugged and stop when the battery is fully charged To interrupt the charging cycle disconnect the AC plug do not disconnect the DC plug BATTERY DISCHARGE INDICATOR The green light moves from right to left as batteries are being discharged When the green light is at the last position on the left the batteries must be recharged A flashing light warns the operator that further discharge will damage batteries See HOBBS indicator instructions KEYSWITCH Depress brake pedal and turn the key switch clockwise for on position Always turn off all switches set the F R selector to neutral set the parking brake remove the key before leaving the vehicle HORN Depress the horn button on the steering column or handle b
49. harging constant current stage Models 912 will display the current to the battery on the bargraph and Model 912 xx1x will flash its LED GREEN off more than on to indicate 8096 charge status The length of charge time will vary by how large and how depleted the battery pack is the input voltage the higher the better and ambient temperatures the lower the better If the input AC voltage is low below 104VAC then the charging power will be reduced to avoid high input currents Models 912 xxOx AC LED and Models 912 xx1x single LED both flash YELLOW If the ambient temperature is too high then the charging power will also be reduced to maintain a maximum internal temperature Models 912 xx0x bargraph flashes and Models 912 xx1x single LED flashes YELLOW When the battery is at approximately 80 state of charge the bulk stage has completed and an gt 80 charge indication is given Models 912 xx0x turn on the 80 LED and Models 912 xx1x will fiash its LED GREEN on more than off In the next phase known as the absorption or constant voltage phase the last 20 of charge is then returned to the battery The charging could be terminated at this point if the vehicle requires immediate usage however it is highly recommended to wait until 100 charge indication is given to ensure maximum battery capacity and life A low current finish charae phase is next applied to return and maintain maximum battery capacity Models 912 xx0x will flash t
50. he 100 LED When Models 912 xx0x 10096 LED or Models 912 xx1x single LED is continuously GREEN the batteries are completely charged The charger may now be unplugged from AC power always pull on plug and not cord to reduce risk of damage to the cord If left plugged in the charger will automatically restart a complete charge cycle if the battery pack voltage drops below a minimum voltage or 30 days has elapsed If a fault occurred anytime during charging a fault indication is given by flashing RED with a code corresponding to the error There are several possible conditions that generate errors Some errors are serious and require human intervention to first resolve the problem and then to reset the charger by interrupting AC power for at least 15 seconds Others may be simply transient and will automatically recover when the fault condition is eliminated To indicate which error occurred a fault indication will flash RED a number of times pause and then repeat 1 FLASH Battery Voltage High auto recover 2 FLASH Battery Voltage Low auto recover 3 FLASH Charge Timeout the charge did not complete in the allowed time This may indicate a problem with the battery pack voltage not attaining the required level or that the charger output was reduced due to high ambient temperatures 4 FLASH Check Battery the battery pack could not be trickle charged up to the minimum level required for the charge to be started This may indicate that
51. irst digit followed by a short pause then the number of blinks for the second digit followed by a longer pause To ch h check change the charging algorithm Battery Type 35 a Disconnect the charger positive Concorde 2xxAh AGM 27 Crown CR325 dv dt connector from battery pack Apply AC Deka 8GGC2 Gel power and after the LED test the generic flooded CP dv dt Algorithm will display for 11 seconds 8 Concorde 1xxAh AGM 1 Determine Mounting Location While its sealed nature allows the charger to be mounted virtually anywhere the choice of mounting location and orientation is extremely important For optimum performance and shortest charge times mount the charger in an area with adequate ventilation The charger should also be mounted in an area that will be relatively free of oil dirt mud or dust since accumulations within the fins of the charger will reduce their heat dissipating qualities Optimal cooling also occurs when the charger is mounted on a horizontal surface with the fins vertical More airflow from below the charger will help cool the fins so mounting above open areas or areas with cut outs for airflow is desirable Contact Delta Q for information on other mounting orientations As the charger may get hot in operation the charger must be installed such that risk of contact by people is reduced The charger s AC plug must be located at least 18 above the floor ground surface and the status disp
52. is PMC potboxes are factory set and rarely require user attention To test and adjust connect an ohmmeter to the potbox wires and use this procedure 1 With the spring holding the lever arm against the return stop the resistance should be less than 50 ohms Slowly move the lever If the resistance abruptly starts to increase when the lever is 3 mm 1 8 from the stop 1 5 mm 1 16 for potboxes without the microswitch no adjustment is needed Curtis PMC 1204X 1205X 1209 1221 Manual 45 23 MAINTENANCE amp ADJUSTMENT 2 Ifadjustment is required loosen the screw holding the lever on the pot shaft Use a screwdriver to rotate the pot shaft slightly with respect to the lever Recheck the point at which the resistance starts to increase and continue making adjustments until the increase starts at 3 mm 1 8 at 1 5 mm 1 16 for potboxes without the microswitch When adjustment is correct tighten the screw holding the lever on the pot shaft then recheck to see that this action did not disturb the adjustment Make sure that the lever is still seated down on the pot shaft below the slight bevel on the end of the shaft 3 Check the resistance with the lever pushed all the way to the other stop It should be between 4500 and 5500 ohms If it is outside this range the potbox is faulty and should be replaced 4 For potboxes equipped with a microswitch check for correct switch operation Use an ohmmeter or simply listen for the sligh
53. ith the defective part s to MOTREC within 30 days after repair was done No compensation will be allowed for damages caused by vehicle downtime It is the responsibility of the owner of the vehicle to make sure that the driver is properly trained and instructed in the safety features and operation of the vehicle including vehicle stability as required by OSHA and ANSI B56 Operators shall read understand and follow the safety and operating instructions in MOTREC Manual before driving the vehicle Operators shall not be permitted to drive the vehicle unless a complete and adequate training has been provided Driving a vehicle constitutes a hazard The driver is responsible for the control of the vehicle while driving and must always evaluate and care for all peculiar situations that he or she may meet while driving The driver assumes the inherent hazards related to this activity The vehicle is designed for off road use only MOTREC disclaims any liability for incidental or consequential damages to include but not be limited to personal injury or property damage arising from vehicle misuse lack of maintenance or any defect in the vehicle It is the responsibility of the Owner of the vehicle to make sure that the service technicians are properly trained as required by OSHA and ANSI B56 Service technicians shall read understand and follow instructions in the MOTREC manual before servicing the vehicle Only qualified and authorized personnel shall be p
54. lay must be visible to the user b To change algorithm touch positive connector during the 11 second display 2 Mounting Procedure period to the battery pack s positive Mount the charger by the mounting plate using appropriate terminal for 3 seconds and then remove Trojan J305 dV dt fasteners i e 1 4 or with locking hardware For UL2202 the Algorithm will advance after 3 15 DEKA 8G31 Gel compliance a 12AWG green bonding wire with ring terminals seconds Repeat until desired Algorithm 5 Trojan 30XHS must be attached from the bonding stud located on the front of the is displayed 30 second timeout is 4 US Battery US2200 charger identified by to the vehicle frame The vehicle extended for every increment Trojan T 105 connection must be made using corrosion resistant hardware Incrementing beyond the last Algorithm Table 1 e g 10 stainless steel machine screw with at least two moves back to the first Algorithm threads of engagement and if required a paint piercing washer After desired Algorithm is displayed touch the charger connector to the battery positive until the output relay is 3 DC Battery Connection Procedure heard to click 10 seconds algorithm is now in permanent memory The green wire outputs battery voltage when the charger is not c Remove AC power from the charger and reconnect the charger positive plugged into AC to provide an interlock function see Fig 1 If connector t
55. le that does not operate in forward is brought in for repair STEP 1 Examine the vehicle and its wiring for any obvious problems such as broken wires or loose connections STEP 2 Connect the programmer select the Diagnostics Menu and read the displayed fault information In this example the display shows No Known Faults indicating that the controller has not detected anything out of the norm STEP 3 Select the Test Menu and observe the status of the inputs and outputs in the forward direction In this example the display shows that the forward switch did not close when forward was selected which means the problem is either in the forward switch or the switch wiring STEP 4 Check or replace the forward switch and wiring and repeat the test If the programmer shows the forward switch closing and the vehicle now drives normally the problem has been corrected 27 8 DIAGNOSTICS amp TROUBLESHOOTING Table5 TROUBLESHOOTING CHART PROGRAMMER LCD DISPLAY FAULT CATEGORY EXPLANATION POSSIBLE CAUSE HW FAILSAFE1 2 3 1 self test or watchdog fault Controller defective M SHORTED 1 internal M short to B Controller defective FIELD OPEN 1 field winding fault Motor field wiring loose 2 Motor field winding open ARM SENSOR armature current sensor fault Controller defective FLD SENSOR field current sensor fault Controller
56. lid GREEN EN 61000 4 3 Radiated radio frequency EMF immunity Here Flash RED ENG1000 44 Electicalfasttransien burstimmunty DC Ammeter ________ LEDBargraph 1 126100045 Surgeimmuniy 0 Bat Temp Compensation Automatic Optional EN61000 46 immunity Auto restart if V lt 2 1Vpc or 30 days elapse EN 61000 4 11 Voltage variations immunity 1A Installation Instructions AN WARNING The output of chargers with greater than 48V may Charger NC Interlock pose an energy and or shock hazard under normal use These Internal NO 8 B units must be installed in the host eguipment in such a Output O manner that the output cable and battery connections are B only accessible with the use of a tool by gualified personnel BLKANHT Figure 1 4 Check Change Charging Algorithm The charger comes pre loaded with algorithms for batteries as detailed in Table 1 If your specific battery model is not listed please contact Delta Q Each time AC power is applied with the battery pack NOT connected the charger enters an algorithm select display mode for approximately 11 seconds During this time the current Algorithm is indicated on the 80 LED Models 912 xx0x or on the single LED Models 912 1 A single digit Algorithm is indicated by the number of blinks separated by a pause A two digit Algorithm is indicated by the number of blinks for the f
57. nion shaft lock O ring axle shaft Bolt housing cover self locking 5 16 18 x 5 8 also serviced in assy group 4010 Use with axle WEC A B 7200 724S 7300 760B 7627 Use with axle 7800 762P Stud housing cover 5 16 18 and 5 16 18 x 1 1 2 long also serviced in assy group 4010 use with axle 7600 762P Cup driving pinion bearing front 488048 Cone and roller drive pinion front bearing HM88048 QTY AR AR AR AR AR 53 PART NUMBER FORD WEC NON LOCKING REAR AXLE SERVICE PARTS LIST NO 237 DSAZ D9AZ D9AZ D9AZ D9AZ 712 E7TZ E7TZ DSAZ 7 0942 2 E7TZ C7AZ C7AZ B7A D5AZ 502 E7UZ 4067 4067 AG 4067 4067 AJ 4067 4067 AL 4200 4204 4204 4211 4215 4216 4221 4222 4228 4228 4230 4230 4628 4630 A 4662 A 4663 4670 4676 4851 4851 389546 5100 170 E6TZ 4859 4859 A DESCRIPTION Shim differential bearing adjustment Cont d 299 thick 301 thick 303 thick 305 thick 307 thick Differential assy reler to group in Section 40 Case assy differential Use with axle 7200 724S 730D 1987 Shaft differential pinion kit use with axle 87200 7245 7300 1987 Consists of 1 E7TW 4211 Shaft 1 0887 4241 Pin Pinion kit use with axle 720 7245 7300 1987 Consists of 2
58. o overturn and jack knife when traveling on inclines or when carrying a heavy load e Always drive straight up and down the face of an incline never across the face to prevent overturn and trailer jack knife Drive slower and start applying brakes sooner on inclines to adjust for longer stopping distance e Use extra care and drive slowly in reverse in congested areas or on wet or slippery ground e Keep to the right under normal conditions Maintain a safe distance from all objects e Slow down and sound the horn when approaching a corner or other blind intersections e Before leaving the vehicle park on a level ground flat surface turn off all switches set the forward reverse switch to neutral set the parking brake remove the key Do not park the vehicle on an incline e Before battery charging park the vehicle in a well ventilated area set for Do not operate it when charging To interrupt a charging cycle disconnect the AC plug disconnecting the DC plug or a battery terminal or operating the vehicle could damage the charger and produce a spark battery explosion and acid splashing e Use another driver to steer this vehicle while it is towed Be sure the driver uses brakes when you slow or stop the towing vehicle Do not exceed 5 MPH or carry any passenger while towing this vehicle Instructions OPERATING INSTRUCTIONS It is the responsibility of the owner of this vehicle to ensure that the operator understands the operatin
59. o the battery pack It is highly recommended to check a newly used a user supplied 1A fast blow external fuse must be changed algorithm by repeating step 4 above installed inline to prevent damage Shorting or drawing more than 1A may damage charger and void the warranty Product warranty is two years please contact dealer of original equipment for warranty b Securely fasten the black ring terminal from the chargerto the service negative terminal NEG NEGATIVE of the battery pack Note This is a Class A product In a domestic environment this product may cause radio c Check that the correct charge algorithm is being used referto interference in which case the user may be required to take adequate measures section 4 Securely fasten the red ring terminal to the positive Aug 2006 Delta Q Technologies Corp All rights reserved PN 710 00xx Rev 1 V1 16 terminal POS POSITIVE of the battery pack 76 Spare Parts Strobelight polemount Amber 12 80V 3116000001 Red 12 80V 2469001 Blue 12 80V 3690008 Strobelight cab mount Amber 12 48V 3116250001 Red 12 48V 3069026 Blue 12 48V 3069014 Amber 72 80V 3116720001 Red 72 80V 3116720002 Blue 72 80V 3116720003 Amber turn lamp 12V 3069020 Bulb 12V 3069021 Red Tail Brake light Grommet 3269001 Plug 246012A 12V 2469021 24V 2469022 Red Tail Brake light 12V 386002 MOTREC ILLUSTRATED ACCESSORIES Red
60. oltage between output terminal on the key switch and the terminal on the battery gage if not B replace the key switch Check voltage across DC DC converter output terminals if not 12 Volt replace the converter Depress the accessory switch check voltage across accessory terminals If not 12 Volt replace the switch If 12 Volt replace the accessory FORWARD ONLY On a SEPEX motor control check the reverse signal input on the controller On a series wound motor control a bad reverse contactor is the most probable cause of the problem Switch to reverse and check voltage on the reverse control wire If not B replace the F R switch If B turn off the key switch disconnect batteries disconnect power terminals on the F R contactors check the resistance across N C power terminals of the reverse contactor If not 0 ohm change the reverse contactor If 0 ohms switch to forward and check the resistance across the forward N O power terminals If not 0 ohms change the forward contactor 20 Maintenance REVERSE ONLY On a SEPEX motor control check the forward signal input on the controller On a series wound motor control a bad forward contactor is the most probable cause of the problem Switch to forward and check the voltage on the forward control wire If not B replace the F R switch If B turn off the key switch disconnect batteries disconnect power terminals on the F R contactors check the resistance across N
61. on Use the following adjustment procedure The keyswitch should be off during adjustment 1 Remove the socket head screw 1 8 Allen for the adjustment you want to make 2 Adjust the internal potentiometer using a small insulated screw driver available from Curtis 3 Replace the socket head screw and nylon seal washer To pre vent stripping do not over tighten Curtis PMC 1204 1205 Manual 36 23 Curtis Speed Controller CURTIS PMC MOTOR CONTROLLER 37 MANUAL CURTIS 1204X 1205X and 1209 1221 MOTOR CONTROLLERS 1999 CURTIS INSTRUMENTS INC DESIGN OF CURTIS PMC 1200 SERIES CONTROLLERS PROTECTED BY U S PATENT NO 4626750 1204X 1205X 1209 1221 Manual 98796 Rev D May 1999 38 Fig 1 Curtis PMC 1205X full feature electronic motor controller Models 1204X 1209 and 1221 have identical connections OVERVIEW OVERVIEW Curtis PMC Model 1204X 1205X and 1209 1221 electronic motor speed controllers are designed to provide smooth silent cost effective control of motor speed and torque on a wide variety of industrial electric vehicles Like all Curtis PMC 1200 series controllers the 1204X 1205X and 1209 1221 models offer superior operator control of the vehicle s motor drive speed Key features of these controllers include 4 4 Infinitely variable drive and brake control Power MOSFET design provides high efficiency for reduced moto
62. one or more cells in the battery pack are shorted or damaged 5 FLASH Over Temperature auto recover Charger has shutdown due to high internal temperature which typically indicates there is not sufficient airflow for cooling see Installation Instructions 1 Charger will restart and charge to completion if temperature comes within accepted limits 6 FLASH QuiQ Fault an internal fault has been detected If Fault 6 is again displayed after interrupting AC power for at least 15 seconds the charger must be brought to a qualified service depot Maintenance Instructions 1 2 3 For flooded lead acid batteries regularly check water levels of each battery cell after charging and add distilled water as required to level specified by battery manufacturer Follow the maintenance and safety instructions recommended by the battery manufacturer Make sure charger connections to battery terminals are tight and clean Do not expose charger to oil dirt mud or to direct heavy water spraying when cleaning vehicle See flip side for Product Specifications and Installation Instructions for qualified personnel 75 Spare Parts Specifications DC Output see Operating Instructions Model 912 24xx 36xx _ Voltage nom V Mechanical All models Dimensions 48xx 72 28 0 x 24 5 x 11 0 cm 11 x 9 7 x 43 Voltage max V Weight ____ lt 5 kg 11 Ibs
63. r and battery losses and silent operation High pedal disable HPD function monitors throttle status during turn on and prevents operation until throttle has been returned to neutral optzonal feature Thermal protection and compensation circuit provides both under temperature and overtemperature cutback as well as steady current limit throughout the entire operating range Undervoltage cutback function protects against low battery voltage includ ing low voltage caused by external loads More Features gt Curtis PMC 1204X 1205X 1209 1221 Manual 39 OVERVIEW Fault detection circuitry monitors battery throttle connections output transistors bypass contactor etc to prevent runaway conditions V Static return to off SRO function requires that forward or reverse selectors be returned to neutral before output is allowed optional feature v Emergency reverse enhances plugging current when belly button is acti vated on walkie type applications optional feature N Delayed bypass LA output drives a bypass contactor optional feature V Forward reverse and bypass contactor driver outputs are internally pro tected against shorts in the contactor coils N Simple installation with no adjustments reguired V Tin plated solid copper bus bars v Push on connectors for control wiring Familiarity with your Curtis PMC controller will help you to install and operate it properly We encourage you to rea
64. ravity of each cell if a cell is shorted voltage drop may occur only when there is current 18 Maintenance BATTERY CHARGER WARNING Always unplug the AC and DC electrical cords before attempting any repairs to the charger CHARGER DOES NOT TURN ON cord of portable chargers must be disconnected from batteries after every charge to restart Check dc fuse links Check battery voltage at the battery connector Check ac outlet and cordset Replace electronic control RELAY CLOSES AND TRANSFORMER HUMS BUT AMMETER DOES NOT REGISTER Check dc fuse links Check the continuity of the dc output cord ammeter diodes and all connections in the dc circuit Check diodes Check capacitor rapidely increasing resistance SINGLE CHARGER FUSE BLOWS Disconnect and check diodes BOTH FUSE LINKS BLOW Check the battery pack and battery connector polarity Disconnect and check diodes CHARGER OUTPUT IS LOW Disconnect and check diodes Can be caused by a transformer failure AMMETER READS 30 AMPS FOR MORE THAN 30 MINUTES Check the battery pack CHARGER DOES NOT TURN OFF Check specific gravity in each battery cell As much as 16 hours may be required to properly charge heavely discharged new or cold batteries Replace electronic control AC LINE FUSE OR CIRCUIT BREAKER BLOWS Check ac cordset Check ac line fuse rating Replace elec
65. roads and highways This vehicle is designed to be driven in buildings e electrical system of this vehicle will make sparks which can ignite inflammable materials Never use the vehicle in hazardous areas where there are inflammable materials explosive dust or fumes in the air e Have your vehicle inspected regularly by trained personnel and cease operation if a malfunction occurs e Do not open battery compartment to prevent battery explosion acid splashing severe damage to eyes or skin Do not open motor compartment Keep clear from moving rotating wheels sheaves etc or lifting parts e Never carry more passengers than number allowed for this vehicle Wait until all occupants are seated and holding on before moving Always keep all body parts inside vehicle Keep both hands on steering wheel e Do not exceed the vehicle cargo load capacity and gross trailing weight capacity rated for flat hard even surface Different operating conditions such as loose terrain or ramps reduce vehicle capacity e Avoid loose unbalanced or top heavy loads to keep a good stability and prevent overturn Do not load cargo that can fall off the vehicle Do not carry cargo that is longer wider or higher than this vehicle e Always depress slowly the accelerator for smooth acceleration Avoid stunt driving or horseplay e Avoid sharp turns always slow down before turning to prevent vehicle overturn or trailer jack knife Vehicle is more sensitive t
66. s only Head operator s instructions in owner s manual prior to driving General security warning label Operation of this vehicle is restricted to authorized persons only Head operator s instructions in owner s manual prior to driving Do not operate on roads public streets and unauthorized areas Never open battery compartment Never open motor compartment Warn people to stay away from wheels and moving or lifting parts Never exceed specified max speed cargo or passenger capacity Drive slowly on ramps in turns In reverse Avoid loose cargo Before turning on key switch and while moving be sure that occupants keep all their body parts inside vehicle occupants keep holding on hand rails wheel chair if applicable is secured with tie down Straps trailer attachment if applicable is secured with two chains Before leaving this vehicle park on a flat surface set to neutral set the parking brake turn off all switches and remove the key Respectively key switch markings forward reverse selector markings and light switch marking ke F WD Maintenance PERIODIC MAINTENANCE CHECKLIST WARNING Maintenance operations must be made by properly trained service technicians Keep clear from moving parts such as tires sheaves and motor Check for all EE protections when applicable and keep cables and wires clear from mechanical and rubbing action Batteries contain sulphur acid that can
67. s required to reduce risk of electric shock do not use ground adapters or modify plug Do not touch uninsulated portion of output connector or uninsulated battery terminal Disconnect the AC supply before making or breaking the connections to the battery while charging Do not open or disassemble charger Do not operate charger if the AC supply cord is damaged or if the charger has received a sharp blow been dropped or otherwise damaged in any way refer all repair work to qualified personnel Not for use by children Operating Instructions Always use a grounded outlet When using an extension cord avoid excessive voltage drops by using a grounded 3 wire 12 AWG cord 4 2 Product Manual for QuiQ 912 24xx 36xx 48xx 72xx Unit 3 5250 Grimmer St Burnaby BC Canada V5H 2H2 INFORMATIONS IMPORTANTES DE SECURITE Conserver ces instructions Ce manuel contient des instructions importantes concernant la s curit et le fonctionnement Information de S curit de la Batterie www delta q com Attention Utiliser seulement sur les batteries 72V avec un algorithme appropri au type sp cifique de batterie voire le manuel D autres types de batteries pourraient clater et causer des blessures ou dommages Les batteries peuvent produire des gaz explosives en service normal Ne jamais fumer pr s de la batterie et viter toute tincelle ou flame nue proximit de ces derniers Fournisser la bonne
68. sed DISC BRAKES Check pad linings for excessive wear the linings should have a thickness exceeding 1 16 1 5 mm Disc brakes are self adjusting BRAKE PEDAL If the brake pedal becomes soft or spongy air may have entered the hydraulic system and the brake system has to be bled 1 2 QE fill the master cylinder with brake fluid DOT 3 bleed front callipers one at a time by having someone applying a steady pressure on the brake pedal and close the bleeder before allowing the brake pedal to return to up position fill the master cylinder with brake fluid DOT 3 bleed rear wheel brakes one at a time following the same procedure fill the master cylinder with brake fluid DOT 3 clean every fitting and line remove traces of oil apply a continuous pressure on the brake pedal for about five minutes Finally inspect brake lines and fittings for leaks 15 Maintenance FRONT AXLE AND STEERING CAUTION Before maintenance turn off all switches set to neutral set parking brake remove the key and raise the front end of the vehicle supporting it with two jack stands of adequate capacity STEERING INSPECTION Check tire inflation pressure suspension components tie rods straightness tie rod ends play wear play wear in wheel bearings kingpins and bushings REPLACING amp ADJUSTING THE STEERING GEAR Remove the pitman arm The steering box makes 6 5 turns center the
69. steering gear 3 25 turns from either side Align the front wheel straight Install the pitman arm TOE IN ADJUSTEMENT With the wheels in straight forward direction measure the inside left to right distance between the front tires at the front and rear of the tires Turn the rear tie rod until the distances are equal and tighten the two lock nuts on the tie rod REMOVING amp GREASING OF FRONT HUBS required once a year Remove dust cap and cutter pin unscrew nut remove hub Inspect bearings and races for wear and replace worn bearings Replace the seal Pack the hub with wheel bearing grease and re assemble ADJUSTING FRONT HUBS Tighten spindle nut to 30 ft lb to seat the bearing and back off the nut to the next slot Install a new cutter pin and the dust cap 216 Maintenance BATTERY MAINTENANCE WARNING It is the responsibility of the owner of this vehicle to ensure that the service technicians are properly trained read and obey the safety rules and guidelines in this manual ANSI B56 Maintenance operations must be made by properly trained service technicians only Before any maintenance work park the vehicle on a flat level surface turn off all the switches set to neutral remove the key lift the wheels off the ground and secure with jack stands of adequate capacity Keep charger disconnected while doing any maintenance work Always wear a face shield and scarf
70. t click the switch makes It should operate when the lever is 1 5 mm 1 16 from the return stop If it does not adjust by loosening the two screws holding the slotted microswitch mounting plate to the stop spacers and moving the plate Recheck the switch operating point after tightening the screws Curtis PMC 1204X 1205X 1209 1221 Manual 46 24 Spare Parts SPARE PARTS 47 Spare Parts BODY REF PART NO DESCRIPTION 1 2363320004 SEAT 1005003 BUCKET SEAT ON SLIDE ADJUSTERS 2 120003 TRIMMING 3 2314320001 FRONT BUMPER 5 300022 5 7 X 8 L R D WHEEL ASS 2223360001 5 00 X 8 SOLID SOFT RUBBER WHEEL 6 2382320011 BACKREST CUSHION 7 2803300009 LEFT HANDLE 2803300008 RIGHT HANDLE 8 2353320001 ROLL OUT BATTERY TRAY 480009 ROLLER 2662002 SPRING LOCK PIN 2352320001 LIFI OUT BATTERY TRAY 2352330013 LIFT OUT BATTERY TRAY E 330 WITH MORE THEM 76in OF DECK AND ALL E 360 E 480 B 330 WITH 62in OF DECK 48 Spare Parts REF PART NO 1 2360320012 2382320009 2 2360320014 2360320015 2360320024 2360320025 3 2803000003 2366320015 4 2365000001 2365000002 5 2367320002 2367320001 2367320008 2367320007 DESCRIPTION STEEL CAB SEATBACK CAB RIGHT DOOR LEFT DOOR RIGHT DOOR REAR PASSENGERS LEFT DOOR REAR PASSENGERS PADDLE LATCH DOOR LATCH RIGHT HINGES KIT LEFT HINGES KIT RIGHT DOOR GLASS LEFT DOOR GLASS CAB REF RIGHT DOOR GLASS REAR PASS LEFT DOOR GLASS REAR PASS
71. tch is ON and seat switch 1s activated PMC may also have an SRO safety feature that prevents the vehicle from moving if the F R switch is activated before turning on the key switch and activating the seat switch The vehicle stops on a steep and long ramp or while towing a heavy load the circuit breaker has open to prevent motor overheating and will reset automatically after one minute The PMC is also equipped with an internal thermal protection that cutback the current until the PMC has cooled down 21 Maintenance NO MOTION Make sure that the PMC surface is clean and dry check the terminal areas Dust Particles or acid contamination can create current leaks and cause a PMC malfunction Check F R switch Turn on the key switch and set to forward Check voltage between the forward terminal and the terminal on the battery gage check voltage between the reverse terminal and the terminal on the battery gage if both B replace the F R switch Check switches and wiring Disconnect control terminals on the PMC and check all control signals If a switch pin does not read B check wiring or replace the switch Check potentiometer Turn the key switch to OFF disconnect potentiometer terminals Check the resistance across terminals if not within the recommended limits adjust or replace the potentiometer Check for shorts between potentiometer wires and vehicle frame resistance should read at least 1 megohm Check main cont
72. tery voltage overvoltage shutdown limit Vehicle operating with charger attached Battery disconnected during regen braking THERMAL CUTBACK over under temp cutback Temperature gt 85 C or 25 C Excessive load on vehicle Improper mounting of controller Operation in extreme environments ANT I TI EDOWN Curtis PMC 1244 Manual Mode 2 or Mode 4 selected at startup 28 Mode switches shorted to B 2 Mode switches tied down to select Mode 2 or Mode 4 permanently 78 8 DIAGNOSTICS amp TROUBLESHOOTING LED DIAGNOSTICS A Status LED is built into the 1244 controller It is visible through a window in the label on top of the controller This Status LED displays fault codes when there isa problem with the controller or with the inputs to the controller During normal operation with no faults present the Status LED flashes steadily on and off If the controller detects a fault a 2 digit fault identification code is flashed continuously until the fault is corrected For example code 3 2 welded main contactor appears as OOD Uu G 0 OD gu 3 2 252 3 2 The codes listed in Table 6 Table6 STATUS LED FAULT CODES LED CODES EXPLANATION LED off no power or defective controller solid on controller or microprocessor fault controller operational no faults not used hardware failsafe fault
73. tronic control Can be caused by a transformer failure 19 Maintenance ELECTRICAL TROUBLESHOOTING WARNING Maintenance work must be performed by trained service technicians only It is the responsibility of the owner of this vehicle to ensure that the services technicians are properly trained understand and obey the safety rules and guidelines ANSI B56 All service technicians must read and understand the maintenance warning section in this manual WARNING Before any maintenance work park the vehicle on a flat level surface turn off all switches remove the key lift the wheels off the ground secure with jack stands of adequate capacity disconnect charger Always wear safety glasses Batteries emit highly explosive gases that can be ignited by a spark Before disconnecting a high current terminal turn off all switches disconnect battery charger disconnect batteries Keep clear from moving parts such as tires sheaves and motor PMC SELF DIAGNOSTIC If your PMC comes with a status led use the flashing code to help troubleshooting BATTERY VOLTAGE Make sure batteries are securely connected Measure voltage between and terminals We will call this value B or full battery voltage ACCESSORIES NOT WORKING Check the fuses on the batteries and the DC DC converter Check voltage across and terminals on the battery gage if not B check wiring Turn the key switch ON check v
74. uctions applicable to the type of repair maintenance or service Always wear a face shield and gloves when working around batteries Before opening the battery compartment disconnect the charger turn off all switches and remove the key Batteries emit highly explosive gases which greatly increase when charging do not disturb connections or produce sparks around batteries to avoid a battery explosion and acid splashing Battery acid causes severe damage to eyes or skin Flush contaminated area immediately with water Use insulated tools to avoid sparks that can cause battery explosion and acid splashing Use two counteracting tools double wrench technique when disconnecting or tightening terminals on the battery and the speed controller to avoid cracking the terminal or battery post welds Before cleaning or replacing a battery charger speed controller contactor relay diode or any other component in the power circuit always disconnect the charger turn off all switches remove the key wear a face shield and gloves identify battery polarity and disconnect battery leads discharge the capacitor in the controller with a 10 ohms 25 W resistor for a few seconds across B and B After cleaning the power must not be reapplied until terminal areas are thoroughly dry On EE Rated vehicles make sure that the control box is sealed the static strap makes good contact with the ground the motor is sealed by bands the cable protectors are prop
75. ure to use the double wrench technique could cause undue strain to be placed on the internal connec tions and could also result in cracked seals around the bus bars WIRING TYPICAL INSTALLATION Curtis PMC 1204X 1205X 1209 1221 controllers are designed to satisfy the requirements of material handling applications using series motors Figure 8 is a schematic diagram of the installation shown in Figure 7 Wired this way the vehicle will plug brake if the direction is changed with the vehicle moving and the throttle applied Reversing is accomplished via a forward reverse changeover contactor or two single pole double throw 2xSPDT contactors Coil suppres sion diodes should be used on the main and forward reverse contactors KSI Wiring The keyswitch input KSI circuit includes inputs from the keyswitch and from the various interlocks The controller KSI is used to turn the controller on and off KSI is turned on by connecting it to battery B Any positive voltage greater than about 8 volts will turn on the controller but usually the full vehicle battery voltage is used In its simplest form KSI is operated by a keyswitch that turns the vehicle off and prevents unauthorized use The keyswitch should also turn off the main Curtis PMC 1204X 1205X 1209 1221 Manual 42 12 WIRING L j CONTEA KEYSWITCH INTERLOCKS TUN not used with SRO controllers gt pP uot POLARITY 4 PROTECTION POWER WIRING DIODE FUS
76. ward and reverse inputs Keyswitch input KSI Throttle inputs F R contactor output Bypass contactor output Emergency reverse input Forward input Reverse input Several manufacturers make mating connectors that fit this connector The part numbers listed are for the recommended 0 75 18 AWG vinyl insulated stranded wire MFR PART NUMBER DESCRIPTION AMP 640426 7 locking insulation displacement terminals wires at right angle to connector Methode 3300 107 218 locking insulation displacement terminals Molex 09 50 3071 locking crimp terminals Panduit CE156F18 7 locking insulation displacement terminals wires at right angle to connector Curtis PMC 1204X 1205X 1209 1221 Manual 41 1 WIRING CONNECTIONS High Current Four tin plated solid copper bus bars are provided for the high current connec tions to the battery and motor Negative connection to battery Positive connection to battery and to motor armature Output to motor field Plug diode to motor armature The cables used for the battery and motor connections must be heavy enough to carry the high current required Rubber insulated welding cable is convenient to work with because of its flexibility Connections to the controller bus bars should be made with lugs suitable for the cable used fastened by M8 5 16 bolts and nuts When tightening the bolts two opposing wrenches should be used Fail

e-360 a modifier

Contents

Download Pdf Manuals

Related Search

Related Contents