Corel Ventura - A17224.CHP
Contents
1. Connect the equipment into an outlet on a circuit different from that which the receiver is connected Consult the dealer or an experienced radio television technician for help 2001 11 22 OVERVIEW The ACS 1722 and the ACS 1724 represent a revolutionary new direction in KVM Keyboard Video Mouse Switches a dual function two and or four Port KVM Switch 2 Port USB 2 0 Hub combination As KVM switches users can access two ACS 1722 or up to four ACS 1724 computers from a single PS 2 keyboard mouse and monitor using USB 2 0 technology to handle the data connection between the KVM switch and the connected computers At the same time they allow the computers PCs and Macs to access two additional USB 2 0 peripheral devices on a one computer at a time basis Before the development of the KVM Switch the only way to control multiple computer configurations from a single console was through a complex and costly network system Now with the ACS 1722 ACS 1724 you can easily access two to four computers in a cost effective manner Setup is fast and easy plugging cables into their appropriate ports is all that is entailed There is no software to configure so there is no need to get involved in complex installation routines or be concerned with incompatibility problems Since the ACS 1722 ACS 1724 intercepts keyboard input directly it works on any hardware platform and with all operating systems2. Master View needs to be reset Turn off the computers wait 5 seconds turn the computers back on Video Problems Loose cables Check all cable connections to make sure they are completely seated in their sockets Resolution and or Bandwidth set too high This unit supports VGA SVGA Multisync and XGA interlaced with resolutions of up to 1920x1440 Hz Cable quality not good enough We strongly recommend that you use high quality cables Use of high quality cables should eliminate video problems 1 Some Notebooks notably the IBM Thinkpad and Toshiba Tecra have trouble when their mouse and keyboard ports are used simultaneously To avoid this only connect the mouse port or the keyboard port If you connect the mouse port you will need to use the notebook s keyboard when the notebook becomes the active computer 13 2001 11 22 LIMITED WARRANTY IN NO EVENT SHALL THE DIRECT VENDOR S LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT DISK OR ITS DOCUMENTATION The direct vendor makes no warranty or representation expressed implied or statutory with respect to the contents or use of this documentation and especially disclaims its quality performance merchantability or fitness for any particular purpose The direct vendor also reserves the right to revise or upd
3. 5 Plug the keyboard and mouse into the Console Keyboard and Mouse port connectors on the front panel of the unit Plug the monitor into the Console Video port connector on the rear panel of the unit Use one of the Custom Cables provided with this package to connect any available Video USB port combination on the KVM switch to the USB and Video ports on the computer you are connecting up Repeat step 2 for any other computers you are connecting up Plug the Power adapter into an AC source then plug the adapter cable into the unit s Power Jack Power on all devices Note 1 The Power On default is to link to Port 1 If the computer 6 attached to Port 1 is inactive the monitor will be blank so it may appear as if the unit is not functioning This is not the case Simply press the Port Selection Switch to switch to an active computer port 2 The Mac s keyboard Power On function is not supported You must start the Mac with its Power On switch Plug the USB peripherals into either USB type A port The first time that the peripherals are introduced to each compter Windows will install the necessary drivers for them Refer to the note under USB Peripheral Ports on p 6 2001 11 22 2001 11 22 OPERATION Controlling all the computers in your A
4. USER MANUAL ACS 1722 ACS 1724 Read this guide thoroughly and follow the installation and operation procedures carefully in order to prevent any damage to the units and or any devices that connect to them This package contains 1 ACS 1722 or ACS 17244 KVM Switch 2 ACS 1722 or 4 ACS 1724 Custom Cable Sets 1 Power Adapter 1 User Manual If anything is damaged or missing contact your dealer Copyright 2001 ATEN International Co Ltd CE Manual Part No PAPE 1200 100 Printed in Taiwan 11 2001 2001 11 22 Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause interference to radio communications However there is no guarantee that interference will not occur ina particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver
5. The ACS 1722 ACS 1724 provides two convenient methods to access the computers connected to the system using the push button Selection switch located on the unit s top panel and entering Hotkey combinations from the keyboard There is no better way to save time and money than with a ACS 1722 ACS 1724 installation By allowing a single console to manage all of the attached computers the ACS 1722 ACS 1724 eliminates the expense of purchasing a separate keyboard monitor and mouse for each one Additionally it saves the extra space they would take up and eliminates the inconvenience and wasted effort involved in constantly having to move from one PC to the other 2001 11 22 FEATURES Dual Function KVM USB 2 0 Switch One Console Controls 2 ACS 1722 or 4 ACS 1724 Computers and Two Additional USB 2 0 Devices Fully Compliant with the USB 2 0 Specification Supports Transfer Rates of 1 5 12 480 Mbps Fully Backward Compatible to USB 1 1 Supports Microsoft IntelliMouse and the Scrolling Wheel on Most Mice Easy to Install No Software Required Connecting Cables to the PCs Is All It Takes Easy to Operate PC Selection Via Push Button Switch or Hotkeys Auto Scanning LED Display For Easy Status Monitoring LED Overcurrent Detection for USB Ports Hot Pluggable Superior Video Quality Up To 1920 x 1440 DDC2B Compatible With All Operating Platforms Efficient Ergonomic Design Logical
6. Connector Layout Saves Time Space Power and Equipment Costs 2001 11 22 SYSTEM REQUIREMENTS CONSOLE A VGA SVGA or Multisync monitor capable of the highest resolution that you will be using on any computer in the installation APS 2 style keyboard APS 2 style mouse COMPUTERS The following equipment must be installed on each computer that is to be connected to the system A VGA SVGA or Multisync card A6 pin mini DIN PS 2 Style mouse port A6 pin mini DIN PS 2 Style keyboard port with 5V DC on pin 4 A USB Host Controller installed on the system Windows XP 2000 Win 98 SE ME Transfer speeds of up to 480Mbps can only be achieved with USB 2 0 driver support Currently Windows XP and Windows 2000 have native USB 2 0 support Support for other Windows versions will be forthcoming 2001 11 22 AGS 1722 FRONT VIEW 1 ATEN Q 2 3 4 1 Port Selection Auto Scan Switch Pressing this switch toggles the KVM focus between the two ports Holding the switch down for 3 seconds activates Auto Scan Mode pressing the switch while Auto Scan Mode is active turns Auto Scan Mode Off 2 CPU Port LEDs A lit LED indicates that its corresponding Port is the one that has the KVM focus A flashing LED indicates that the corresponding port is being accessed under Auto Scan Mode 3 USB Port LEDs The LED lights GREEN to indicate that th
7. CS 1722 ACS 1724 installation from a single console could not be easier Two CPU Port selection methods that provide instant access to the computers are available Manual CPU Port Selection Hotkey CPU Port Selection MANUAL GPU PORT SELECTION With Manual Port Selection you simply press the Port Selection button to switch the KVM focus to the next Port If you are at Port 4 ACS 1724 you cycle back to Port 1 The CPU Port LED lights to indicate which Port has the KVM focus HOTKEY CPU PORT SELECTION Hotkey navigation allows you to select the active computer directly from the keyboard instead of having to manually select it with the Port Selection switch The ACS 1722 ACS 1724 provides two Hotkey navigation features Selecting the Active Port Auto Scan Mode Selecting the Active Port There are two methods to select the port for the KVM focus 1 You can switch to the next computer port by pressing and releasing the left or right Ctrl key twice in rapid succession Ctrl Ctrl 2 Each CPU Port is assigned a Port Number 1 2 3 or 4 You can switch directly to any port by holding down the Ctrl and Shift keys then pressing the Function Key that corresponds to the CPU Port number and then releasing them all together Ctrl Shift Fn Where n represents a Port Number from 1 to 4 2001 11 22 Note 1 The Ctrl and Shift Key combinations must be on the same side both on the Left or bot
8. ate the device or documentation without obligation to notify any individual or entity of such revisions or update For further inquiries please contact your direct vendor 14 2001 11 22
9. e USB port it corresponds to is ONLINE If an overcurrent situation occurs the LED changes to AMBER to indicate overcurrent status 4 Console Keyboard and Mouse Ports The cables from your PS 2 keyboard and PS 2 mouse plug in here Each port is identified by an appropriate icon 2001 11 22 AGCS 1724 FRONT VIEW cPul cPU2 CPUS CPUS USBI USB2 1 Port Selection Auto Scan Switch Pressing this switch shifts the KVM focus to the next ascending port 1 to 2 2 to 3 etc When you reach Port 4 you cycle back to Port 1 Holding the switch down for 3 seconds activates Auto Scan Mode pressing the switch while Auto Scan Mode is active turns Auto Scan Mode Off 2 CPU Port LEDs A lit LED indicates that its corresponding Port is the one that has the KVM focus A flashing LED indicates that the corresponding port is being accessed under Auto Scan Mode 3 USB Port LEDs The LED lights GREEN to indicate that the USB port it corresponds to is ONLINE If an overcurrent situation occurs the LED changes to AMBER to indicate overcurrent status 4 Console Keyboard and Mouse Ports The cables from your PS 2 keyboard and PS 2 mouse plug in here Each port is identified by an appropriate icon 2001 11 22 AGS 1722 AGCS 1724 REAR VIEW 1 2 3 SJE lees E mE Jo of
10. f J T 4 5 1 2 i z 5 6 ei i ei eis yo af Yo af je af jo ee 1Y I 5 1 Power Jack The DC 5V Power adapter cable plugs in here 2 USB Peripheral Ports Cables from any USB peripheral devices you wish to attach plug in here Note Most USB devices CCD Cameras Scanners Printers e g require their drivers to be shut down before disconnecting the device from the system Otherwise the system may crash When you switch computers with the Port Selection Switch it is the equivalent of disconnecting the device Therefore if you have peripheral devices other than a second keyboard and mouse connected to these ports you must be sure to shut down the USB drivers for them before switching computers 3 CPU Port Connectors The USB cables that provide the data link to the computers plug in here 4 Console Video Connector The cable from your monitor plugs in here 5 CPU Port Video Connectors The video cables that link to the computers plug in here 2001 11 22 INSTALLATION Before you begin make sure that power to all the devices you will be connecting up have been turned off To prevent damage to your installation due to ground potential difference make sure that all devices on the installation are properly grounded Refer to the diagram on p 8 and follow the steps below 1
11. h on the Right LCtrl LCtrl1 or RCtrl RCtrl LCtrl LShift or RCtrl RShift If the Ctrl Ctrl combination conflicts with programs running on the computers an alternate method of pressing the Scroll Lock key twice in rapid succession is available In order to use this alternate method you must first invoke it by holding down the Ctrl and Shift keys then pressing the F12 Function Key Ctrl Shift F12 For any Ctrl Shift combination you can also press and release the Ctrl Shift and Function keys in sequence Ctrl then Shift then Fn Auto Scan Mode The ACS 1722 ACS 1724 s Auto Scan feature automatically cycles through the Ports at regular 5 seconds intervals so that you can monitor the computer activity without having to take the trouble of switching yourself To invoke Auto Scan Mode 1 Hold down the Ctrl and Shift keys 2 Press the F10 key down then release all three of them together Note 1 2 LCtrl LShift F10 As an alternate method you can also press and release the keys in sequence LCtrl then LShift then F10 Once scanning begins it continues until you press the Spacebar to exit Auto Scan Mode The Port that was currently active at the time scanning stopped remains active While Auto Scan Mode is in effect ordinary keyboard and mouse functions are suspended and USB peripheral ports are disabled You must exit Auto Scan Mode by
12. in mini DIN F Connectors Mouse 1 x 6 pin mini DIN F Monitor 1x 15 pin HDB F CPU KB Mouse 2 x USB Type B 4 x USB Type B Connectors Video 2x 15 pin HDB F 4x 15 pin HDB F Peripheral Connectors 2x USB Type A Resolution 1920 x 1440 DDC2B Scan Interval 5 secs Operating Temperature 0 50 C Storage Temperature 20 60 C Humidity 0 80 RH Non condensing Housing Plastic Weight 200 g 390 g Dimensions L x W x H 120 x 64 x 44 mm 195 x 70 x 43 5 mm SA 2001 11 22 TROUBLESHOOTING Symptom Cause Action Keyboard and or Mouse Not Responding Loose cables Check all cable connections to make sure they are completely seated in their sockets Master View is in Auto Scan Mode Press the Spacebar to exit Auto Scan Mode Keyboard needs to be reset Unplug the keyboard from the Console Keyboard Port then plug it back in Mouse needs to be reset Unplug the mouse from the Console Keyboard Port then plug it back in Mouse in Unsupported Mode Some mice can be set to act as either a PS 2 or serial mouse Make sure the mouse is set to PS 2 mode Because of the wide variety of mouse driver standards for the modern series of mice the ones with the extra buttons and wheels this unit only supports all of the extra features of the Microsoft Intellimouse It supports the scroll wheel function of most other mice
13. pressing the Spacebar in order to regain their normal functions 10 2001 11 22 HOTKEY SUMMARY TABLE Combination Action L Ctrl L Ctrl or Shifts the KVM focus to the next CPU Port R Ctrl R Ctrl Default Method Scroll Scroll Shifts the KVM focus to the next CPU Port Alternate Method Ctrl Shift F1 or Shifts the KVM focus to CPU Port 1 Ctrl Shift F1 Ctrl Shift F2 or Shifts the KVM focus to CPU Port 2 Ctrl Shift F2 Ctrl Shift F3 or Shifts the KVM focus to CPU Port 3 Ctrl Shift F3 Ctrl Shift F4 or Shifts the KVM focus to CPU Port 4 Ctrl Shift F4 Ctrl Shift F10 or Invokes Auto Scan Mode Ctrl Shift F1 0 Ctrl Shift F12 or Invokes the Alternate Hotkey Method Ctrl Shift F 12 ACS 1724 only SELECTED LED DISPLAY Activity Meaning Off Port is not selected On Steady Port is connected to an active computer Flashing On and Off equal Port is connected to an active computer and is being accessed in Auto Scan mode E 2001 11 22 SPECIFICATIONS Function ACS 1722 ACS 1724 Power Consumption DC 5V 180 mW max DC 5V 400 mW max Port Selection Pushbutton Switch Hotkeys CPU Ports 2 4 CPU LEDs Selected 2 Green 4 Green USB LEDs Online 2 Green Normal Amber Overcurrent Console Keyboard 1x 6 p
Download Pdf Manuals
Related Search