Home

User Manual - OBR

1. Fuel injection correction f FuelCalib Now look into the groups listed in AVAILABLE ITEMS Any group starting with an exclamation mark indicates differences between the two maps Opening the group any constant calibration table or map marked in green will be different between the two maps To see the differences between i e the two fuel maps open the fuel map in both maps The coloured cells indicate that values differ between the two maps While online you can compare maps in the ECU with maps on your PC s hard disk Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 48 of 67 Ocr Control Systems Ole Buhl Racing UK Ltd 8 1 COPY AND INSERT DATA You can copy parts of a map or complete maps and paste the data into the same map or different maps and documents spreadsheets etc Mark the map cells to copy by clicking on the first breakpoint hold the left mouse button down and drag the cursor to the last breakpoint to copy Press CTRL C to copy the data Now mark the other part of the map where you want to copy the data to Make sure you highlight the same number of cells in the map you are copying to Press CTRL V to paste the data Click or press F8 to save the changes or F11 to discard changes You can copy the data to anothe
2. C Potentiometer Software M Send Defaulf if disab Iw Vertical Horizontal General Max Limit 14 88 14 88 Control Min Limit 15 00 15 00 Default value 0 00 right large main potentiometer as 2 The minor 4 Ame pot based correction config jw Enable correction from AMC to map 1 jw Map is visible potentiometers are numbered 3 6 Click on the desired AMC potentiometer or click Map 1 descriptor EQRUSMOEDIMERSDMOODES gt POTENTIOMETER SOFTWARE to disable the AMC and switch to a keyboard operated AMC Controller l potentiometer In this case you can use the mouse to operate the slider or PgUp and PgDn keys Click VERTICAL or HORIZONTAL to select the potentiometer orientation NOTE Do not change the setting in MAX LIMIT and MIN LIMIT lt is possible to display a part of the map on which the potentiometer is active Mapping breakpoints are clearly visible and corrections can be stored directly into the ECU map from either the AMC or the keyboard Click ENABLE CORRECTION FROM AMC TO MAP 1 to activate this facility To enable the map visualisation click on MAP IS VISIBLE If no text is visible in the window click on the button and then double click on the descriptor file valid for the ECU map Click OK to add this new potentiometer to your display screen Press F4 to activate the potentiometers Press F4 again to deactivate the potentiometers Ole Buhl Racing UK Ltd Telephone 44 0 1
3. e Now create a new folder for storing your engine maps anywhere convenient for you on your hard disk but it is suggested to do so alongside the DEVICE and USER folders For example name this folder EDITOR or MAPS Move the remaining EDT file from the CD to your newly created EDITOR MAPS file NOTE If this is a new installation of EFI software including the old version of ECT the software could have installed to the default location of C Program Files EFl Technology ECT MOD The DEVICE USER amp EDITOR folders may need to be manually created with a new installation Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 9 of 67 DESTA contro systems Ole Buhl Racing UK Ltd 2 2 CONFIGURING THE CAN INTERFACE The CAN interface is the communication module supplied by EFI Technology and it is used to establish connection between your PC and the ECU The ECT Modular programme has the Capability to run either a parallel port or USB CAN link The CAN link settings are selected by opening the ECU Comms server programme individually from ECT Select the main windows Start button then All Programs ECUCommServer The programme will open to a small icon on your lower windows toolbar Left click ECU Comms s
4. es TECHNOLOGY Engine Management Systems Ole Buhl Racing UK Ltd TECHNOLOGY ECT MODULAR SOFTWARE DESCRIPTION User Manual Version 3 7 23 Date September 2012 This document is property of Ole Buhl Racing Ltd Reproduction Prohibited Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE VAT No GB 722 5686 27 United Kingdom Ocr Control Systems Ole Buhl Racing UK Ltd Index 1 CLESEN 4 1 1 INSTALLATION RE 4 2 CGONFIGURING EG E 9 2 1 TRANSFER THE DATA FILES See note below 9 2 2 CONFIGURING THE CAN INTERFACE EE 10 2 3 PARALLEL PORT CAN INT TERAFC E 11 2 4 USB CANINTERFAC EE 12 2 SINTE EE 13 3 1 DEVICE DETUR EE 14 3 2 PROFILE ea eT ee ee 14 33 B PEAT EE 14 3 4 KRIS NEE ERC EE 15 3 5 REIH ee de 15 3 6 TAN eggs RE EE 15 Ca El E 16 3 8 ECU SETUP EE 18 3 9 PUELEEARN MAP EE 19 J10 ES 19 A MENOR INTERFACE EE 20 4 1 SETEN G EH 20 4 2 ECU COMM EE 20 4 3 KSC 20 4 4 RE CENE E 21 4 5 TRANSMIT SE TUP EE 22 4 6 RE CEWE ETOF MAP EE 22 4 7 RESET DIAGNOSTIC RE ME EE 23 4 8 S OG BB BE NR 23 4 9 RESET COUNTER EE 23 AO EEA N EE 24 411 TRANSMIT AER EE ed 24 4 12 RECEIVE FUEL LEARN EE 25 Bede LEARN Ce EE EE EE Ee 25 tla PRESET oen ee ee ee 25 4 15 THROTTLE POSITION CALIBRATION 0 occa cece ccccecssecesecesecseeeseeeseeuseeuseaueeaesuaueueeueueenness 25 INT Ge
5. Press OK start logging data Press F3 again to stop logging data Specify a name for the EVENT which will become the subfolder in the DATA folder where the data is saved to Select target event Specify a file name for the data at the bottom of the screen mp The log file will automatically convert and you will be asked to ag specify a time axis channel Now select file again and exit The original comma separated file is still available in the User folder and it can be imported into Excel Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 31 of 67 Ocr Control Systems Ole Buhl Racing UK Ltd 6 WORKING WITH THE EDITOR 6 1 HOW TO LOAD A MAP WORKING ON LINE WITH THE ECU Selecting ENGINE MAP gives access to the map containing data for the engine calibration for all our systems To load a map working online with the ECU Map loaded from ECU Device EURO section is not visible click the small button tO enerslMap Information vallable items the left of the text ji Click on the arrow in the DEVICE window and go to section Map Loaded from ECU If this Map E 1 MG25 FR3 2 MG25 FA3 click on the ECU configuration you are using Click on the arrow in the MAP window and select the map you want to load
6. SUZ RACE Approx time s H Select the correct type of ECU in section SELECT DEVICE and click on the target directory for the data omg o Then click DOWNLOAD Et o A status window appears showing the amount of bytes downloaded If you have disabled the automatic deletion of data after downloading in the main ECT LOG INTERFACE SETTINGS section you will now be asked if you want to delete the data in the ECU Click YES or NO As soon as the message Data Download OK appears and you see the blue bar you can disconnect from the ECU while ECT writes the data to disk Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 27 of 67 DESTA contro systems Ole Buhl Racing UK Ltd 5 3 DATALOGGER SETUP The logger can record data from any ECU channel Ee atalogger Setup EE Selection Select Device from list You can create a file containing the channels you EURO12 407 x want to log either working online or offline with the Factory name Channel sought Acc Fuel AcceCntlOLCond AcceCntlOLCond 400 Air Air Temp 46 Air Temp2 52 Baro Press 41 Base Fuel Map 182 Battery Key 24 Boost RP DF Out 3A1 Channel sought Descriptions Speed m s Vehicle Speed in Metres per Second Frequency H2 Log max time 01 33 12 EN Trigger 100 Trigger
7. CELLS IN A RON 41 6 14 CHANGE THE VALUE OF ALL CELLS IN THEMA 42 6 15 CHANGING THE VALUE OF A BREAKRROINT ccc cece ecccessecseeseeseeeseeseceseeeeeuseeeaeeeeesaeeaeneas 43 6 16 CONFIRM CHANGES EE 44 6 17 DELETE AND INSERT BREAKPOINTS eanenennnesnernnnnrnnrnnrnrnnrnrrnrrnrrrnnrrnrnrrnrrnrerinrerrnrerinrenrerrnnns 44 6180 GRAFO DOUGFLAY EE 45 6 19 GRAPHIC DISPLAY PROPERT Y esaeeneennnennnnrnnnnnnrnnrnnnnrnnrernnrrnrnrrnrrnrnrrnnrnrnrrnrerrnrrnrerrnrrnrerrnnnt 47 T PRIN RE 47 9 COMPARE MAPS ee ee 48 8 1 COPY AND INSERTI DATA EE 49 8 2 SANE CHANGE EE 51 9 WORKING WITH THE DISPLAY MANAGER 52 9 1 DISPLAYING ENGINE IDATA E 52 9 2 DISPLAY WANAGE R rececuscvccscaticenncdcqcennteadnensmenadsenece semensdeadsounee diddineenioenseedsiqeadediserecedtsewteeterenecdtacennent 53 9 3 CREATE DIGPLAY GROUP ssace tecetesacns eni idine EERE ecucncecataiece teceneaavecsesnaientaceuatedacaainerss 53 9 4 GCGOPY DISPLAY GROUP Ee 54 9 5 EINEN DiS PY EE 54 9 6 EDIT A DISPLAY SGREEN EE 54 9 7 ADDING TEA RE 54 9 8 ADD CHANNE E 55 9 9 ATD a lt param OE E ee ee ee ee ee ene ee eee 56 910 ADDPOTENTOME VER sitcsiccstasscndsecerodaticomadustnrenosdiet cenbdesecindacvaaeudsenieunsectitaueduagedadadtisenncesiveypactiaenades 56 911 ABD OST a E 58 912 ADD MEMORY EN Hee EE Ed be 58 9 13 CHANGE PROPERTY OF CHANNEL LED AND POTENTIOMEIER 58 9 14 POSITION OF ITEMS ON DISPLAY SCREEN eisiccccicceiievccssecsdacosvacsicelecteiessvtavesbeuseiucccevencbesteunecade 58 9 15
8. CHART OFF Click on CHART OFF if you want to return to the numerical display screen Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk United Kingdom Page 63 of 67 DESTA contro systems Ole Buhl Racing UK Ltd 11 WORKING WITH THE ECU DATABASE 11 1 GENERAL The ECU s uses a database for storage of general information about the internal data channels The database holds information about the ECU communication positions Device Manager of the channels in the memory configuration of channels etc Select Device from list EURO12 402 Open EURO1 HC110 SE Ze 11 2 OPEN THE DATABASE Gs From within the main menu click on DEVICE SETUP to enter into the DEVICE MANAGER Click on the name of the device that applies to you then click OPEN IA Ware versi ion 4 01 When it opens you will see the following screen Do NOT change the CAN ID ID Can Static Table Descriptions 10 JEURO 1 2 firmware version 4 01 VALUE Check Data You can set the channel default colour for display screens by selecting FORE and BACK buttons for both the channel name and the channel value 11 3 DATA PROPERTIES Click the tab CHANNELS If you are Sa Device WEVICE EURO12 407 DEV EURO1 2 402 MDB Device CanInfo Data Properties searching for a specific channel type String expressi
9. EE 27 5 1 ETING EE 27 5 2 Eege 27 5 3 DATALOGGER SE TUP cated reacts dene disarengan Eea a aie aa eaa eteaccaseiessbodeensasaceenace ESENAD 28 5 4 CLEARING LOGGER MEMOR EE 30 5 5 CONVERT LOGGED DISPLAY DATA TO 2D FORMAT 30 6 WORKING WITH TRAE EDITOR areca tec a A eee AEE EE EN 32 6 1 HOW TO LOAD A MAP WORKING ON LINE WITH THE ECH 32 6 2 HOW TO LOAD A MAP WORKING OEFEINE co cc eccceccecceesseceeeeeeseueeeeseaeueueeeeueeeeeeuaneeeeuaes 33 6 3 GENERAL MAP INFORMATION 34 6 4 AVAILABLE ITEMS rreren ae a Ea DE a T E E Ea Eea Eea 35 6 5 MODIFY A CONSTANT 0 ccc ccc cccccccccccccecscceseeeseeuseeueeeueeeueeueeeuaueuaueaaeeueeeuaueuaueuueauueaueeuueeaueeaueeuseeneesees 35 6 6 MODIFY A CALIBRATION TABLE O DIMENSIONAT ccc ccccccceeeeseeeeeseeeeeseeeeseaseeseeesaaeees 36 6 7 CHANGE THE VALUE OF ONE CG BUN vecitehicccchesecszecconosueeteransichecussvcnsvanencdecusseatevuntictecust encyancncveeescies 36 6 8 CHANGING THE VALUE OF SEVERAL CELLS EE 37 6 9 MODIF IA MAP EE 38 6 10 CHANGE THE VALUE OF ONE CELL EE 39 6 11 CHANGE THE VALUE OF SEVERAL CELL 40 6 12 CHANGE THE VALUE OF ALL CELLS IN A COLUMN cecccceecseeeeee essen eeeeeeeseeeeneeeenes 41 Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 2 of 67 Ocr Control Systems Ole Buhl Racing UK Ltd 6 13 CHANGE THE VALUE OF ALL
10. House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 38 of 67 Ocr Control Systems Ole Buhl Racing UK Ltd 6 10 CHANGE THE VALUE OF ONE CELL Move the cursor to the cell which value you want to alter e Press Enter to open the property window Type a new value Press Enter to confirm or e Use the to increase or keys to decrease the cell value or e Type an offset value positive or negative in the window CORRECTION Press Enter to confirm or e Type a percentage correction positive or negative in the Window CORRECTION Press Enter to confirm When a cell s value is changed the background colour changes to red to indicate a new value To cancel all changes press F11 If you want to store this value in your map press F8 The changes however are not saved on your computer until you save the map Remember to give the altered map a new name if you wish to keep the original Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 39 of 67 Ocr Control Systems Ole Buhl Racing UK Ltd 6 11 CHANGE THE VALUE OF SEVERAL CELLS Click the first cell to mark it hold the left mouse button drag the cursor to the end and then release the button All marked cells turn blu
11. MAP EDITOR in the ECT Main menu When the window EFI MAP EDITOR opens press ESC to close the engine map template Now click MAIN and then SETTINGS RE Enable multiple descriptors w Enable learn tools w Enable setup map Select your preferred options It is strongly recommended to enable the learn tools which are used by all our ECU s Enable the access to ECU setup maps if you are working with other ECU s than just Euro 1 Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 15 of 67 DESTA contro systems Ole Buhl Racing UK Ltd 3 ENGINE MAP selecting ENGINE MAP gives access to the maps containing data for the klap manager engine calibration for all our systems Engine Map ECU Setup Map These maps can be modified working either online with the ECU or by loading Fuel Lean Map the map from your PC Delete map To load a map whilst working online with the ECU click on Map Manager and an engine map template open Look for the small square next to Map loaded from ECU ___ P DE a Click on the arrow in the DEVICE window and click eeler Wangen on the ECU configuration you are using i Click on the arrow in the MAP window and select the map you want to load You can load the map from any of the avail
12. Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 20 of 67 Ocr Control Systems Ole Buhl Racing UK Ltd Section Select Kernel Firmware FPGA Test lists the ECU firmware You will have to transmit the firmware to the ECU when you receive a new ECU or when you need to update the current software version Click on the square box to select the firmware version then click Send Firmware and follow the instruction given on screen The engine maps are listed in the Select Map section Click on the square box to select the desired engine map All ECU s except Euro 1 can be programmed with 2 to 6 different maps The option for the desired map location is listed in section Select Destination Map Click on the location number desired and then click Send Map to ECU After transmitting the map to the ECU you will be prompted for a password You can use maximum 8 characters 15 with Euro 4 Euro 8 and any key combination except and If you do not want to protect your map with a password simply press Enter IMPORTANT If you transmit a new map generated by mixing the old map and a learn map you must reset the learn map 4 4 RECEIVE Map Upload c IBM_PRELOAD x Since each version of ECU s uses a different je EURO12 407 PRIDE EURO12 409 comm
13. RESIZE CHANNEL WINDOWS AAA 59 9 16 DISPLAY LAYOUT DESGRIP TION visdesccceceteseweceseinenbcctieaccccnssneadawtdgantuebstundedtnegniveseneniweiteasteehstunsedeede 59 I Ge CA al so E EE 59 918 RENAME DISPLAY EE 60 919 PELETE DOPA EE 60 920 COGGING DATA EE 60 921 U8 REN NN EE 61 10 SERR OFAR T WEE 62 10 1 CREATE A STRIP Ee TA NEEN 62 IZ FROPER Ee 63 103 SINGLE MUL TIP E 63 TOFIN ERV AL EN 63 19o PAU EE 63 E CHARI ee 63 11 WORKING WITH THE ECU DATARAGE ccc ccccccccccccccccccscecseeeseeeseeuseeuseueeeueseueeeueeeuaeeuaueueesuaesuaesnaneees 64 ha E ml col BEE 64 2 ea CR gm DATABASE EE 64 TL3 DACA PROP VE oceectstcnscwancensstantenstnadeeuseauadseosse E E seta odes AE EAEan a E ANa ANASARE aawa 64 12 Sit 65 121 ON EE 65 t22 SL RING EXPRESSION SOUGHT NEE 65 12 3 POTENTIOMETERS AND ACTIVE MAPPING CONTROLLER seeererresrnerrisrrerrinrrerrrerreerrenn 65 13 SELF LEARNING WE 66 Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 3 of 67 Ocr Control Systems Ole Buhl Racing UK Ltd ECT Modular 3 7 23 1 INSTALLATION GUIDE ECT Modular is the latest PC software from EFI Technology for use with its market leading ECU s ECT Modular 3 7 23 should only be used with the following EFI Technology CAN interfaces 1 Aluminium USB interface versi
14. and click ENABLE EDIT MODE to close the window editor A faster method is to close the screen and click OK to save the changes Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 58 of 67 Ocr Control Systems Ole Buhl Racing UK Ltd 9 15 RESIZE CHANNEL WINDOWS You can resize any channel window in order to create a more harmonic Water Temp A Oil Press e ebe ac e ic Feis T to cham QRS D C bar C dec WW bar mouse button and click on NW Battery K ENABLE EDIT MODE Fuel Temp Fuel Press G C bar a Phase Lower 3 dec Battery Yolts Move the cursor to the lower right corner of the group of windows and click again Click right mouse button and click on SELECT GROUP Place the cursor in the upper left corner of the group of windows to mark and click left mouse button Click on REDIM then choose a reference channel window and click on it When done click the right mouse button and click SAVE DISPLAY Click the right mouse button again and click ENABLE EDIT MODE to close the window editor A faster method is to close the screen and click OK to save the changes You can align the channel windows in a similar manner vertically or horizontally move a group or delete a group
15. and data file e One with NTP extension a notepad file in which you can include information about the engine sensors etc File name PC i e i e One with TAB extension the actual data pe ricn M a file T Open as read only Ze lf the ECT cannot find the file without extension or the specified descriptor file tt asks you which descriptor file you want to load The editor uses the descriptor file to visualise the data from the engine map The descriptor file is given a unique name identifying it to the type and version of ECU and whether the engine load is throttle based AN or pressure based SD Click on the correct version and click OK to load the map The engine map descriptor file extension is DES Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 17 of 67 Ocr Control Systems Ole Buhl Racing UK Ltd 3 8 ECU SETUP MAP Selecting ECU SETUP MAP gives access to the map containing data configuring the ECU s to specific engines and their sensors Please note that Euro 1 does not use an ECU setup map The map can be modified working either online with the ECU or by loading the map from your PC IMPORTANT Do not change the ECU Setup Map online while the engine is running The ECU has to be reset before the engine is running on
16. by 18 to reach the target lambda value Refer to section 13 on how to mix the learn map with the existing fuel map Select the map file to DELETE TAB file H Ed 3 10 DELETE MAP Look in E Eurol 171 edt IC al cl a 160htf tab a Niss 11 tab l C Download el Ian ab el Gtin ca tab el p8 270 TA lf you want to delete a map from your hard disk E Honda el 160hta tab el Gtinca2 tab el Taxiseql t l C install 220 car TAB lot16011 TAE click MAP EDITOR and then DELETE MAP 160htd tab el 306gprwt tab el Mafbag b tab 306n tab el Mofbact Lab Make sure the window LOOK IN displays the p data directory related to the ECU in use ae e Click on the map you want to delete and then fiesofwpe Mapte taB ETa m Cancel click OPEN T Open as read only The map is now removed from your hard disk Z Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 19 of 67 DESTA contro systems Ole Buhl Racing UK Ltd 4 MEMORY INTERFACE This section is used to send and receive all types of maps and to access the lean system 4 1 SETTINGS To access the communication interface options click on MEM INTERFACE in the ECT Main menu When the window EFI MEM INTERFACE opens click MAIN and then SETTINGS nable diagnostic data Reset nable setup
17. can be visualised in a 2 dimension graphic layout expressing the map variable as a function of the breakpoints expressed either by the column or row values TPS 30 078 APM 4500 TerogBase 4956 13000 l 1 l 1 l 1 l 1 12000 11000 4 10000 4000 S000 rogi HU S000 4000 3000 2000 1000 s l l l l l l D l D l l l l l l D l D l l l D l l l D l D KL 1000 1500 2000 2500 3000 3500 4000 4500 s000 FOO 6000 6500 ZU 500 8000 8500 9000 INCI F3 Brkp F10 Save Fil Cancel Graph Row Graph Column Al Single Click on GRAPH ROW or GRAPH COLUMN to make your selection To view the data in a 3 dimensional mode click 3D GRAPH The values of the actual map breakpoint is visualised in the upper left corner of the graphic display It is possible to modify the map in graphic mode too Use the F6 and F7 keys or the UP and DOWN arrows keys to move from line to line and click on the graph to select a breakpoint The point at which the marked line and blue breakpoint line cross indicates the cell being modified The X amp Y values of this point are displayed above and to the left of the graph table Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 45 of 67 Ocr Control Systems Ole Buhl Racing UK Ltd e Use the keyboard or displa
18. have depending on your selections three new icons on your desktop E FECT A ge di LEB remaja falaa e EETA CICE CE HEUTE Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 8 of 67 DESTA contro systems Ole Buhl Racing UK Ltd 2 CONFIGURING ECT Now the programme is installed there are just 4 further steps before it is ready to use 2 1 TRANSFER THE DATA FILES See note below Using Windows Explorer copy the data files from the CD ROM provided stored in ECU data files to the directories automatically created on your hard drive when the ECT Modular programme was installed These may have alternatively been e mailed to you To achieve this follow the procedure below e Using Windows Explorer right click on your CD drive normally D e From the drop down menu select Explore e From the list of files now shown on the CD double click on the ECU DATA FILES folder e Open the folder corresponding to your ECU type Le Euro 4 v305 e Unzip the large file by double clicking on it This will open to three folders a DEV folder USR folder and an EDT folder e Move the DEV folder into the DEVICE folder created on your hard drive in the ECT directory e Move the USR folder into the USER folder created on your hard drive in the ECT directory
19. only SE lf the ECT cannot find the file without extension or the specified descriptor file tt asks you which descriptor file you want to load The editor uses the descriptor file to visualise the data from the engine map The descriptor file is given a unique name identifying it to the type and version of ECU and whether the engine load is throttle based AN or pressure based SD or if it is a setup file Click on the correct version and click OK to load the map The engine map descriptor file extension is DEG and the setup map file extension is CDS Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 33 of 67 DESTA contro systems Ole Buhl Racing UK Ltd In this case you may see the message The length of the Map does not match with the length specified by the descriptor Click OK to continue Note If you are unsure whether the engine has been mapped under throttle load referring to an AN type descriptor file or pressure based referring to a SD type descriptor file then check under the SYSTEM SETUP item in the main engine map options 6 3 GENERAL MAP INFORMATION Once a map is loaded its name appears in the upper left corner of the editor window You can get more information about the map by opening the section GENERAL MAP INFORMATION
20. this handbook in section 9 for instructions on how to create and configure your own display screen and the use of templates When you click in DISPLAYS a list of available display screens is displayed Click on the one you want to load with the mouse or move the cursor with the arrow keys and hit Enter Pressing the first letter of a screen name i e F for FUEL makes the cursor jump to the first screen starting with this letter and if none other exists opens it Refer to section 9 for Serial Port Settings Advanced options information on altering display screen layout SIE re 19200 re COM2 C 19200 COM3 C 28800 C 38400 3 4 DISPLAY SETTINGS p E C 115200 OK Cancel To access the basic display options click on DISPLAYS in the ECT Main menu When the window EFI DISPLAYS opens click MAIN and then SETTINGS If you use the Active Mapping Controller or the ASAPS serial link vw Enable learn tools Enable ASAP menu you must enable the serial ports and configure the settings 7 Disable Pot ter Stoe vw Enable factory name w Automatic conversion from LOG ETL file to 2D format In Advanced Options select your preferred options 3 5 MAP EDITOR The Map Editor opens the editor and gives access to the data in both the engine and the ECU Setup maps Both types of maps can be accessed working either online with the ECU or offline 3 6 MAP SETTINGS To access the basic map editor options click on
21. to decrease the cell values or e Type an offset value positive or negative in the window CORRECTION Press Enter to confirm or e Type a percentage correction positive or negative in the Window CORRECTION Press Enter to confirm When a cell s value is changed the background colour changes to red to indicate a new value To cancel all changes press F11 If you want to store this value in your map press F8 The changes however are not saved on your computer until you save the map Remember to give the altered map a new name if you wish to keep the original 6 14 CHANGE THE VALUE OF ALL CELLS IN THE MAP Click the text cell in the upper left corner of the map to mark all cells All cells turn blue When all cells are marked you must use key to select either an absolute or a percentage correction e Press Enter to open the property window Type a new value which will be applied on all cells Press Enter to confirm or e Use the to increase or keys to decrease all cell values or e Type an offset value positive or negative in the window CORRECTION Press Enter to confirm or e Type a percentage correction positive or negative in the Window CORRECTION Press Enter to confirm Ole Buhl Racing UK Ltd Telephone 44 0 1425478822 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page
22. window Type a new value which will be applied on all cells Press Enter to confirm or e Use the keyboard or display buttons to increase or to decrease the cell values or e Type an offset value positive or negative in the window CORRECTION Press Enter to confirm or e Type a percentage correction positive or negative in the Window CORRECTION Press Enter to confirm When a cell s value is changed the background colour changes to red to indicate a new value To cancel all changes press F11 lf you want to store this value in your map press F8 The changes however are not saved on your computer until you save the map Remember to give the altered map a new name if you wish to keep the original 6 13 CHANGE THE VALUE OF ALL CELLS IN A ROW Click the breakpoint cell to the left of the row to mark all cells in the row All cells turn blue When all cells are marked you must use key to select either an absolute or a percentage correction Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 41 of 67 DESTA contro systems Ole Buhl Racing UK Ltd e Press Enter to open the property window Type a new value which will be applied on all cells Press Enter to confirm or e Use the keyboard or display buttons to increase or
23. 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 56 of 67 Oc Control Systems Ole Buhl Racing UK Ltd To ease the search type the name of the channel you are looking for in CHANNEL and press Enter To select the potentiometer click on it when it appears Property Window General l Can Setting Fon ans Seti Click on GENERAL to change the text and background i mm colour font style and size gt BackCoor JI SS ees Click NAME UP if you want the channel name on top of the Title Back Color CF Orientation Property OK data I Name UP Unit DOWN jw Name LEFT jw Unit RIGHT Exit Click NAME LEFT if you want the name to the left of the data Not recommended for a potentiometer Click UNIT DOWN if you want the channel unit on top of the data Click UNIT RIGHT if you want the unit to the right of the data Not recommended for a potentiometer Click CONTROL to access the potentiometer property You can assign any selected potentiometer to any of the 6 potentiometers available on the Active Mapping Controller AMC Its potentiometers are numbered from left to right starting with the left large main potentiometer as 1 the Property Window Potentiometer Property e Potentiometer 1 C Potentiometer 2 C Potentiometer 3 C Potentiometer 4 C Potentiometer 5 C Potentiometer 6
24. 42 of 67 DESTA contro systems Ole Buhl Racing UK Ltd When a cell s value is changed the background colour changes to red to indicate a new value To cancel all changes press F11 If you want to store this value in your map press F8 The changes however are not saved on your computer until you save the map Remember to give the altered map a new name if you wish to keep the original 6 15 CHANGING THE VALUE OF A BREAKPOINT A breakpoint is the name given to the points used to map over a range of values e g 800 1000 1250 are RPM breakpoints and 12 5 15 234 17 578 are throttle position breakpoints the engine load The value of breakpoints available in tables and maps are individually configurable Press the F9 key or click the F9 BP tab to activate the breakpoint editor Breakpoint values are modified similarly to cell changes as previously described E g or When you are happy with your breakpoints click F9 again to close the breakpoint editor Fe Save FIT Cancel Numenc Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 43 of 67 Ocr Control Systems Ole Buhl Racing UK Ltd 6 16 CONFIRM CHANGES If you have changed values of one or more cells the background colour changes to red Press F11 to
25. 425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 57 of 67 Ocr Control Systems Ole Buhl Racing UK Ltd 9 11 ADD MEMORY ADR Is a special insertion of a firmware stored detail held within the ECU This is not configurable by the user directly Please contact us if you want any more information on this feature 9 12 ADD MEMORY DUMP Is a special insertion of a firmware stored log held within the ECU This is not configurable by the user directly Please contact us if you want any more information on this feature 9 13 CHANGE PROPERTY OF CHANNEL LED AND POTENTIOMETER To access the property of a channel LED or a potentiometer on your display screen place the cursor on the coloured part of the window you wish to edit click your right mouse button and then click PROPERTY Or alternatively Double click on it Click OK to close the channel property window again 9 14 POSITION OF ITEMS ON DISPLAY SCREEN Point your cursor to the display screen and click the right mouse button Click ENABLE EDIT MODE Place the mouse on the upper left corner of the window you want to move click the left mouse button Move the cursor to the position where you want to display the channel and click the left mouse button again When done click the right mouse button and click SAVE DISPLAY Click the right mouse button again
26. Click on LIMITS CONSTANTS 1 DIMENSIONAL ARRAYS calibration tables 2 DIMENSIONAL ARRAYS maps and select all groups Sections Print file NTP from the group drop down menu Selected group Fuel Main Maps ei jw Limits jw One dim Arrays jw Constants jw Two dim Arrays TES To select just a portion of the map select just the G sections you want e g 2 dimensional maps in the fuel Included letters 000 fo rae Table format injection group You can EI Fie Data Display Learn manac Separator ams also type phrases to specify mio Top marg cm 2 Bott marg em 2 E Save to file C Printer soles A e which parameters to include wens ba e Printer setup OLE1 hp officejet g series i pRinter setup Fon farial 18 16 when printing Data not E tine fe File enter name C ECT DEFAULT PRT Browse E wit T 80 columns matching any words will not Z time z Minimum injection time L be printed Mainimit iniertian time T Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 47 of 67 DESTA contro systems Ole Buhl Racing UK Ltd The data can be sorted either by type of data limit constant calibration table or map or listed according to the individual groups To include the notepad file SECTION 6 3 used to give extra map det
27. F8 ECT EFI Communication Tool Py x File Data Display Leam manager Map manager Windows SI ALFAY6 C TAB LM ap loaded from ECU Map loaded from ECU eeh Map Information Se Map Information yailable items yailable items Fuel D Maximum injection time injection map Minimum injection time injection trim f WATER TEMP Minimum injection time LOWER fuel injectors injection trim f AIR TEMP Minimum injection time UPPER fuel injectors injection trim f MAP Ratin fuel flow rate umnner lower fuel iniecthars iniection trim FITPS m Fuel injection map Fuel injection map Correction lo Correction fo Correction fo 6170 b 4 4 D F9 Brkp Fi0Save F11 Cancel decr F9 Brkp FidSave F11 Cancel Graph Column Numeric Export data Dm Graph Column Numeric Export data Print F2 STORE F3 LOG OFF F4 P AUSER EURO1 USR Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 50 of 67 Ocr Control Systems Ole Buhl Racing UK Ltd 8 2 SAVE CHANGES eal Wee Green 1 Load from File i 5 to fil When you work online with the ECU all changes to the map are stored in the Ge Save to file 43 ECU each time you press F8 pAinter setup Print Exit You can save the map wh
28. Mode Min Disable 12 5 Trigger Channel Max Delay 1 0 1sec Delete 2 Send to ECU Exit ECU In both cases you must initially specify which version of ECU and firmware you are using From the drop down menu in section SELECT DEVICE select the right configuration If you are working online with the ECU the logger GA St ei Bu lt configuration is downloaded from the ECU and visualised in Logged Data lf your ECU hasn t previously been configured a message saying Cannot Read Logger Setup from ECU will appear Click on OK to proceed with your configuration The window below the ECU selection displays all channels available for the logger Use the slider to scroll through the channels To search for a channel type the name or part of it in the Channel sought window and press Enter The channel will appear highlighted in blue and its eee Frequency Hz function appears in Description Bont MAP Tar Te fio S If it is the correct channel click the arrow icon to add the channel to Logged Data Delete By default ECT proposes the maximum sampling rate specified for each channel You can alter this by clicking once on the channel then click on the desired sampling rate displayed in the FREQUENCY window To delete a channel click on its name shown in LOGGED DATA and then click DELETE Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roug
29. NGS does not correspond with your PC hardware e When activated the AMC applies an overall trim of i e the fuel map Press STORE on the AMC or F2 on your keyboard to store the trim into the highlighted breakpoint Corrections applied by any potentiometer are stored into their respective maps 13 SELF LEARNING e The use of the automatic self learn mapping of the fuel injection drastically reduces the time spent mapping the engine e Press F5 to toggle the self learn between DEFAULT LEARN ON and LEARN OFF The default setting is selected within the engine map e If you want to map using the self learn system bring the engine RPM and load to a breakpoint position as seen i e on the potentiometer map on the display screen Screens created for Euro 96 Euro 6 and Euro 12 has a green LED that will light up indicating BREAKPOINT OK A red LED indicates that the measured lambda value is outside the selected bandwidth for the target lambda value Euro 6 Euro 12 only messed lamada ae win Ms arr aie or measured lambda value is within the value Euro 6 and Euro 12 only selected bandwidth for the target lambda The LEARN TRIM indicates the correction to the base map pulse width When the measured lambda value and the target lambda value matches the LEARN TRIM is stable Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr mot
30. Oil Press a eo 11 5 bar 29 C Fuel Temp Fuel Press e vorl aer E Battery 13 6 Volts 0 Phase Lower cL Wu IO CAN lt 4h Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 52 of 67 DESTA contro systems Ole Buhl Racing UK Ltd 9 2 DISPLAY MANAGER Display Manager Display Groups Display screens can be created from a blank Kiem S zor Load group browse screen or easily adapted from existing layouts CS IN Ten It is possible to copy existing layout s rename ss layout s delete layout s and create display pages Displays e e i j Select Display from list Open Create new by combining different display layout s on one ET E pdate Description single page EEN 3 Copy Display ia Insert Link to display browse e SHIFT v Rename Display Click on Data Display and select Display Descriptions Delete ECU displaying raw and engineering data Manager 9 3 CREATE DISPLAY GROUP Exit You can show several displays together on a single display page To create a new layout click on Profile sub groups in the Display Groups section Type a name of the new display page you want to create and then click Create New To allocate existing display layouts for the new display page click Insert Lin
31. Page 62 of 67 Display Information Save Display Save and Lock Display Exit Display sales obr motorsport co uk www obr motorsport co uk Oc Control Systems 10 2 PROPERTIES The channel properties are set within the ECU database but can be individually altered in this section Select Properties from the top left of this strip chart screen Click on the arrow to change channels If you want to change the displayed limits of a channel change the settings found in MIN and MAX Click on COLOUR to change the channel colour Ole Buhl Racing UK Ltd ECT EFI Communication Tool SYNC JE otfsine Properties Ma i m Name Crank Pulse Count Description Crank Sensor Pulse Counter Database PE EURO6 402 DEV EURO6 402 MDB Min fo 10 3 SINGLE MULTIPLE eem Colo Click on SINGLE MULT either to display independent charts for each of O ee the select channels or to display all channels simultaneously 10 4 INTERVAL Click INTERVAL to change the time scale for the viewable part of the chart scale The time interval can be set from 2 seconds to 256 seconds 10 5 PAUSE Nr Ringwood Hampshire BH24 3LE Clicking on PAUSE freezes the chart screen Point your cursor to any part of S F the scale you want to investigate further and click to place a marker By clicking on the buttons with the and you can zoom in or out around the On LI 1 marker Ses D e io Ere CAN Ab 10 6
32. This section might be minimised but a click on the button to the left of the text opens the section MG25 FR3 TAB el MG25 FARS TAB Man loaded from ECU General Map Information Header MG25 FR3 09 14 2000 17 58 Map MG25 FR3 TAB Notes about Map EE MG25 FR3 NTP Descriptor REANTZ0E DES5 Notes about Descriptor ER Bra 20 CMM eg tem ee eee _ Map loaded from ECU General Map Information H Iemg a a In Header you can see the date and time the map file was created The actual map file name is displayed in Map and the descriptor file in Descriptor If you click the button next to Notes about Map you open a notepad file which is linked to the map file You can use this file to list information i e about the engine sensors etc This file is not transmitted to the ECU but remains on your hard disk The notepad file is very useful for keeping track of changes you make to the map as you go along If you click the button next to Notes about Descriptor you open a notepad file which is linked to the system descriptor You can use this file to list general information about the system the software release the mapping procedure etc In both cases remember to save the changes you have made to the notepad file and then close it down Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport c
33. UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 32 of 67 DESTA contro systems Ole Buhl Racing UK Ltd IMPORTANT It is not recommended to alter the ECU setup map online while the engine is running Note Euro 1 Euro 2 and Euro 96 ECU s do not have a separate ECU setup map 6 2 HOW TO LOAD A MAP WORKING OFF LINE File Data Display Leam manager Map manager Windows Load from File Loading a map from your PC click on ENGINE MAP Ext General Map Information or ECU SETUP MAP then click on FILE and finally vailable items click on LOAD FROM FILE Make sure the window LOOK IN displays the data directory related to the ECU in use Click on the map and click OPEN A map consists of 3 files all with the same name but different extensions SC Select the map file to load TAB file EES e One without extension containing information Lookin emasconee del al ol ES about required descriptor file commentary file Sites a Grp tb l Ecu a Subic 9b TAB notepad file and data file Ed161205 a 42 tab e One with NTP extension a notepad file in IG which you can include information about the engine sensors etc Filename g e 7 Jas c l e One with TAB extension the actual data file Fiss af lype Map Fie TAB z caa Open as read
34. You can load the map from any of the available locations You may be prompted for a password then type the correct password to proceed If you do not know the password you cannot access the map An engine map consists of 3 files all with the same name but different extensions e One without extension containing information about required files to load e One with NTP extension a notepad file including your notes about the map e One with TAB extension the actual data file If the ECT cannot find a file without extension matching the map file or the specified descriptor file it asks you which descriptor file you want to load The editor uses the descriptor file to visualise the data from the engine map The descriptor file is given a unique name identifying it to the type and version of ECU and whether the engine load is throttle based AN or pressure based SD Click on the correct version and click OK to load the map The engine map descriptor file extension is DES In this case you may see the message The length of the Map does not match with the length specified by the descriptor Click OK to continue This message appears due to a difference in the map file size in the ECU and on your PC Clicking OK references the two together and corrects any misalignment Selecting ECU SETUP MAP gives access to the map containing data configuring the Euro 6 and Euro 12 ECU s to specific engines and their sensors Ole Buhl Racing
35. able locations You may be prompted for a password Type the correct password to proceed If you do not know the password you cannot access the map EURO 6 firmware version 3 30 ECU Firmware If you have more than one map loaded into the ECU and you are unsure which map is in which location you can do the following Load up any display screen see section 9 and then right click in any empty part of that display screen A drop down menu will appear Select Device Information To load a map from your PC click on ENGINE MAP File Data Display Leam manager Map manager Windows then click on FILE from the main ECT toolbar and Ledler Ele finally click on LOAD FROM FILE zil General Map Information vallable items oo directory related to the ECU in use Click on the map and then click OPEN Make sure the window LOOK IN displays the data Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 16 of 67 DESTA contro systems Ole Buhl Racing UK Ltd An engine map consists of 3 files all with the same name but different extensions e One without extension containing asss 27 Look in E Euro96 300 ect E ed information about required descriptor file reen ij m i Gort p tab el Subic 9b TAB commentary file notepad file
36. access to the display manager and to display screens for your ECU e MAP EDITOR gives access to the engine maps ECU setup maps and learn maps You can also delete selected maps in this section e MEM INTERFACE opens up the programming tool and allows you to send and receive maps between the ECU and your PC e LOG INTERFACE gives access to the ECU on board data logger if available e COMPONENTS ARRANGEMENT allows you to arrange the screen layout when multiple windows are opened e LANGUAGE gives access to select Italian or English language e EXIT shuts the programme down Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 13 of 67 Ocr Control Systems Ole Buhl Racing UK Ltd 3 1 DEVICE SETUP This section is used to access the ECU database or to install a new database to be used with the ECT program A new database is required when you upgrade an existing version of an ECU firmware and when you install a new system The database is supplied by OBR contact us with your details Experienced users can access the database properties and change the configuration of individual channels to suit specific needs and save different configurations 3 2 PROFILES Each individual ECU uses a specific communication protocol for data communication with your PC In th
37. age 7 of 67 DESTA corro systems Ole Buhl Racing UK Ltd The Setup Helper will then start to install the ECU Comm Server The Server allows communication between the ECU and ECT Modular As with ECT Modular you will be asked to select your language choice English or Italian You then have the choice to select the Startup Run option This activates the server as soon as you are signed into your PC or laptop Alternatively the server just opens when you open a communication function within ECT Modular i e display map editor programme mem interface and Log interface data logger lt 5 ECUCommServer 2 6 13 0 Setup RN 2 8 The Server installation will then be completed As Choose Components i DT e II Choose which features of ECUCommServer 2 6 13 0 you want to will the Setup Helper Press Finish i TECHNOLOGY install Check the components you want to install and uncheck the components you don t want to install Click Install to start the installation Select components to install j Description EFI Setup Helper Install Space required 5 9MB Setup in esecuzione ECU Communication Server lt Back Ire Cancel Ceara aaa RRR NS l Finish Cancel IMPORTANT If the installation window for TDLPortlO appears select INSTALL if your PC is running Windows 2000 XP NT or Vista The installation is complete when you accept to reboot the PC With the setup complete you should now
38. ails tick the select file NTP option Further options include Printer Setup and Font 8 COMPARE MAPS You can compare the contents of two maps from your PC Open the editor and load the first of the two maps to compare When loaded click on MAP MANAGER and then FILE and LOAD FROM FILE and load the second map Now click WINDOWS and then TILE VERTICAL el ALFAY6 C_TAB M 8 TAB Iof x Map loaded from ECU i _ Map loaded from ECU j ere Map Information iA Map Information j vailable items vailable items f Fuel D 2D el fSnark Ady 3D Fuel Spark Advance Maps Boost Control Cranking Cylinder Fuel Trims Cylinder Iqnition Trims Filters Fuel Fuel Cut Off Datt NO air Maximum injection time Minimum injection time Minimum injection time LOWER fuel injectors Minimum injection time UPPER fuel injectors Ratio fuel flow rate upper lower fuel injectors Fuel injection map Fuel injection trim f WATER TEMP PS BreakpoLrnit THRU tO DIT Fuel injection trim f AIR TEMP Spark Advance Znd TPS Breakpoint THROTTLE 0 3 DIM Fuel injection trim f MAP Spark Advance 3rd TPS Breakpoint THROTTLE 0 3 DIM Fuel injection trim f TPS Spark Advance 4th TPS Breakpoint THROTTLE 0 3 DIM Fuel injection trim f FUEL PRESS Spark Advance Sth TPS Breakpoint THROTTLE 0 Fuel injection trim f BARO PRESS Spark Advance 6th TPS Breakpoint THROTTLE 0 Upper fuel injector proportional map
39. alter a setting press ENTER To exit press Esc 6 5 MODIFY A CONSTANT To change the value of a constant double click on the text line to open its property window PREINJ j iahli i Prime nech lse width on detection of first Its current value is highlighted in blue When you sank pie TSEC 0 15000 Ok Start to type a new value the old is deleted Press Enter to confirm the change If you are working online with the ECU the new value is stored within the ECU Cancel Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 35 of 67 DESTA contro systems Ole Buhl Racing UK Ltd 6 6 MODIFY A CALIBRATION TABLE 1 DIMENSIONAL A calibration table links values of a sensor or a calculated parameter with a variable output which can be i e an offset or a multiplication factor 165EU3XE TAB Fuel injection correction WATER TEMP Correction fo Correction 0 ATER 30 MULT FACTOR 1 078 Click on the text line of the calibration table to display its data for a particular reference point The values are then displayed above and to the left of the table graph If you are working online an animated cursor displays the current load condition 6 7 CHANGE THE VALUE OF ONE CELL Move the cursor to the cell which value you w
40. ant to alter e Press Enter to open the property window Type a new value Press Enter to confirm or e Use the to increase or keys to decrease the cell value or e Type an offset value positive or negative in the window CORRECTION Press Enter to confirm or e Type a percentage correction positive or negative in the Window CORRECTION Press Enter to confirm Ole Buhl Racing UK Ltd Telephone 44 0 1425478822 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 36 of 67 Ocr Control Systems Ole Buhl Racing UK Ltd When a cell s value is changed the background colour changes to red to indicate that a new value has been entered To cancel all changes press F11 If you want to store this value in your map press F8 By pressing F8 this sends the information to the ECU or stores it in the map on your computer The changes however are not saved on your computer hard drive until you save the map Remember to give the altered map a new name if you wish to keep the original 6 8 CHANGING THE VALUE OF SEVERAL CELLS Click the first cell to mark it hold the left mouse button drag the cursor to the end and then release the button All marked cells then turn blue When multiple cells are marked you must use the key or click the Abs tab below the table graph to select either an absolute correct
41. discard changes Press F8 to save the changes Working online the ECU will immediately run on the new data as soon as pressing F8 has saved the data changes 6 17 DELETE AND INSERT BREAKPOINTS It is possible to delete breakpoints and re insert breakpoints in a new location When inserting a breakpoint in a new location the values of the cells are interpolated in accordance with the surrounding cells Click F9 to activate the breakpoint editor The layout of the button bar changes to EH Save FIT Cancel Numenc N Click on Del BP to remove one or more break points from the map If you want to re insert the deleted break points click on Ins BP Type the value of the new breakpoint in the property window and press Enter The system uses linear interpolation when inserting new breakpoints Click or press F11 to discard changes or F8 to save the changes Click F9 to close the breakpoint editor Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 44 of 67 Ocr Control Systems Ole Buhl Racing UK Ltd 6 18 GRAPHIC DISPLAY You can display the numerical data in a graphic view by clicking the GRAPH button You can increase the size of the graphic display area by closing the numerical display with a click on the NUMERIC button Map data
42. e When multiple cells are marked you must use F12 to select either absolute or percentage correction Press Enter to open the property window Type a new value which will be applied on all marked cells Press Enter to confirm e Use the keyboard or display buttons to increase or to decrease the cell values or e Type an offset value positive or negative in the window CORRECTION Press Enter to confirm or e Type a percentage correction positive or negative in the Window CORRECTION Press Enter to confirm When a cell s value is changed the background colour changes to red to indicate a new value To cancel all changes press F11 If you want to store this value in your map press F8 The changes however are not saved on your computer until you save the map Remember to give the altered map a new name if you wish to keep the original Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 40 of 67 Ocr Control Systems Ole Buhl Racing UK Ltd 6 12 CHANGE THE VALUE OF ALL CELLS IN A COLUMN Click the breakpoint cell on top of the column to mark all cells in the column All cells turn blue When all cells are marked you must use key to select either an absolute or a percentage correction e Press Enter to open the property
43. e Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 61 of 67 Oc Control Systems 10 STRIP CHART Ole Buhl Racing UK Ltd Strip charts are a valuable aid in engine analysis work The strip chart included with the ECT software is a sophisticated flexible tool Any ECU channel can be monitored and each chart can be individually configured A maximum of five channels can be visualised in any display format including full screen m E Leit H F emp HD UL Tem Te 10 1 CREATE A STRIP CHART A strip is created from a display screen You can use an existing display screen but remember that you can only display 5 channels a display with more than that won t activate a strip chart You can sort the channels in strip chart mode in any order Click your right mouse button then click on OUTPUT ORDER and arrange the channels Click OK when done Enable Edit mode Enable Strip Chart mode Click your right mouse button and then click on ENABLE STRIP CHART MODE Be Output order for Log Store and Strip Chart Device Information to switch to the graphic display Ole Buhl Racing UK Ltd Roughwood House Highwood Nr Ringwood Hampshire BH24 3LE United Kingdom Telephone 44 0 1425 47 88 22 Telefax 44 0 1425 47 88 66
44. e Select SYSTEM e Select HARDWARE e Select DEVICE MANAGER In Device Manager you will see the PORTS COM amp LPT branch Double click on it to expand the ports directory It will then list all the parallel ports available within your PC e Double click on the port that has ECP as part of its name i e ECP Printer port In the RESOURCES section note down the top left hand setting e g O3BC as shown below ECP Printer Port LP 11 Properties General Port Settings Driver Details Resources F ECP Printer Port LPT1 e Resource settings Resource type Setting 81 0 Range 03BE WiO Range DPE 07BE Hiii DMA o0 Match this LPT address to the options available in the Server settings as shown above IMPORTANT If your computer doesn t display an ECP configured parallel port then refer to your Windows manual or PC Handbook Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 11 of 67 Ocr Control Systems Ole Buhl Racing UK Ltd 2 4 USB CAN INTERFACE e Plug in your USB CAN interface and wait for the Windows installation option to appear on your screen Select to install the driver AUTOMATICALLY e If you select manual installation follow the on screen instructions directing the search to C Program Files EFI Technology drivers folder i
45. editing of your data display The grey background should now feature a dotted grid pattern Click you right mouse button again for editing options 9 7 ADDING TEXT Property Window Click on TEXT and type the text as you want it to General appear on the screen Font MS Sans Serif E Fore Color ee Click on FORE COLOUR to change the colour of the men text Text Click on BACK COLOUR to change the background Ok colour pa Click on FONT to change font style and size Click on OK to confirm Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 54 of 67 Oc Control Systems Ole Buhl Racing UK Ltd Click EXIT to cancel all changes To remove a text box simply right click and select DELETE whilst in EDIT MODE 9 8 ADD CHANNEL Since each version of ECU s uses a different communication protocol it is important to specify from which ECU you want to display data Click on the arrow in SELECT TABLE to select the Acc Fuel ECU type and version you are using Scroll through the available channels in search of your desired channel To ease the search type the name of the channel you are looking for in CHANNEL and press Enter To select the channel click on it when it appears Property Window General Can Set
46. emory in Euro 1 or Euro 96 ECU s click the Reset Diagnostic Data button To cancel any action click on Exit 4 8 OUTPUT DIAGNOSTICS gt ne Select Device from list gt E12 356 REITER ETB 0035 This section is not relevant for Euro 1 EURO12 407 EURO12 407 PRIDE lt The output diagnostics function allows you to test rei Selected output your output drivers both injection and ignition recor Firstly select your device then use the screen tabs _ Stat Test to select between Injector and Ignition testing Select the driver you want to test for how long and for how many cycles Then click the Start Test button Exit The output diagnostics also allows you to test MFIO s multi function Inputs or outputs 4 9 RESET COUNTERS The reset counter allows the user to zero the time counters within the ECU The counters log the time from ECU power up and engine start Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 23 of 67 DESTA contro systems Ole Buhl Racing UK Ltd 4 10 LEARN Learn Datalogger C Each ECU features a unique self learn management of the fuel injection ENEE By the use of a NTK linear lambda sensor and a lambda target map the EES l l l l l Learn Functions injector pulse width meas
47. erver to open it gt Select Interface Selection to configure your interface settings either USB or PP Parallel Port Here you may also select whether or not to activate the interfaces termination resistor Only when using EFLO6 or EFPO2 interfaces only when interface is plugged in B ECServer TCP IP B ECServer TCP IP Server Information Version Connected clients S Interface Type USB EN DESKTOP Displays 3 7 23 127 0 0 1 51019 ss Ertra Settings Enable CAN termination DOT Interface informations Type USB Baudrate 1000 5E E Seial 20 Fimware Version 0 0 2 0 Close 20 Firmware Version 0 0 2 0 Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 10 of 67 DESTA contro systems Ole Buhl Racing UK Ltd lf you are using a PP interface you also need to configure the port ECServer TCP IP address typically either 0x378 most common or Ox3BC Interface Type x standard configuration for IBM or Lenovo laptops EE Fort EH uSec Delay E8 res 2 3 PARALLEL PORT CAN INTERAFCE e To use a parallel port CAN interface the port must be ECP rated a windows configuration e To find which parallel port is ECP rated click on the Windows main START menu e Select CONTROL PANEL
48. fax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 18 of 67 DESTA corro systems Ole Buhl Racing UK Ltd 3 9 FUEL LEARN MAP Map loaded from ECU The learn map created by the General Map Information vallable them SELF LEARM Hab self learning fuel injection facility Maximum BPM for interpolation in cal tables EPH can be download as described in Minimum BPM for interpolation in cal tables EPH Maximum absolute manifold air pressure mbar section 4 1 D and then loaded into Minimum absolute manifold air pressure mbar Learn calibration map the editor for a closer analysis Loading a map from your PC click on FUEL LEARN MAP then click on FILE and finally click on LOAD FROM FILE Make sure the window LOOK IN displays the data directory related to the ECU in use Click on the map and then click OPEN When the map is loaded click the arrow in the section AVAILABLE ITEMS Click SELF LEARN MAP Double click LEARN CALIBRATION MAP to visualise the learn map All non corrected breakpoints show 1 Fuel has been added if the breakpoint shows a value higher than 1 i e 1 09 shows that the fuel injection pulse width in this breakpoint has been increased by 9 to reach the target lambda value The amount of fuel has been reduced if the breakpoint shows a value less than 1 Le 0 82 shows that the fuel injection pulse width in this breakpoint has been reduced
49. g folder To install in a different folder dick Browse and select another folder Click Install to start the installation Destination Folder C Program Files x86 EFI Technology ECT_MOD Browse Space required 15 3MB d Space available 167 566 lt Back instal Cancel The installation of ECT Modular 3 7 23 is then complete Select close The Setup Helper will then automatically start installing the Pseudo Programmer The Pseudo programmer runs in the background to allow transmission of firmware You do not however need to enter into the PseudoProgrammer software itself Select both the shortcut and quick launch components and select Next The recommended installation path for the programmer is the configured default Select Install The Pseudo Programmer will then complete S PseudoProgrammer 0 5 4 1 Setup Choose Components Choose which Features of PseudoProgrammer 0 5 4 1 you want to install Check che components vou want to install and uncheck the components you don t wank bo install Click Next bo continue Select components to install Required Files _ Shortcut Icon Quick Launch Icon e Description Space required 3 85MB Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom P
50. g rate must be specified too Please contact us for advice on configuring your logger The MIN GRAPH VAL and MAX GRAPH VAL set the range for the channel when selected for use in a strip chart 12 Remarks 12 1 ON LINE e You can open one or several display screens when working online with the ECU e Simultaneously you can have the map loaded into the editor online The animated cursor displays the current engine load condition 12 2 STRING EXPRESSION SOUGHT e When using the String Expression Sought tool to find a channel keep pressing enter to see more channels containing the expression you entered 12 3 POTENTIOMETERS AND ACTIVE MAPPING CONTROLLER e f you have chosen to display part of the related map with a potentiometer an animated cursor displays the current engine RPM and load condition AECH e Press F4 to activate the AMC or the potentiometers on a display screen Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 65 of 67 Oc Control Systems Ole Buhl Racing UK Ltd e The AMC does not work if there are no potentiometers on the display screen e The AMC does not work if the potentiometers on the display screen have been configured for keyboard control e The AMC does not work if the serial port and baud rate in section SETTI
51. he map to display its data table If you are working online an animated cursor displays the current load condition Seles Fuel injection map Correction E Correction TPS EPM 3120 3153 3lz0 3120 3198 3744 4056 4251 4212 3120 3159 S1z0 3120 3198 3744 4056 4251 4212 3120 3159 3159 3159 3237 3627 3300 4017 3822 3120 3159 3237 3276 2354 3545 3744 EELER 3822 3198 3354 3471 3237 EES 3510 3705 3822 32975 23354 232393 3315 EKKRE 3510 3666 3705 3300 4017 3237 3120 23393 4212 4056 3822 3300 4056 4134 3237 3159 3315 4134 4650 3822 4056 4134 4212 EES 3354 3354 23978 4173 460z 4173 4563 4536 23783 EEN 3744 S861 4368 4173 4407 4797 5187 23705 3705 3705 a744 ELE 4251 4365 4953 4992 3744 3361 KEES 4134 4017 4212 4563 4536 4953 23783 29758 23978 23978 4173 4134 4329 S031 S471 3793 4173 4173 4719 4173 4363 4365 4641 S421 4017 4017 4056 4251 4056 4251 4455 4563 S421 4446 4446 4363 4329 4290 4455 4650 4630 6265 4407 4329 43295 4290 4251 4455 4455 4524 4524 4758 4365 43295 4290 4251 4212 4455 4446 4602 4641 4056 3975 3339 3333 4230 4250 4365 4563 4715 4212 4173 4035 4095 4230 4250 4446 4641 4755 4290 4251 4134 4017 4230 42350 4407 4602 4797 4365 4329 4212 4173 4230 4365 4365 4602 4524 4525 4230 4230 4251 4230 4455 4563 4636 4251 427590 4290 4365 4455 4565 4407 4719 5145 You can toggle the cursor ON and OFF by clicking the button F12 ANIMATION Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood
52. hwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 28 of 67 Ocr Control Systems Ole Buhl Racing UK Ltd Logged channels can be set for a quick reset to Channel property page zero value i e before the car is leaving the pit Name Steering E a i Dimension Degrees garage This way it is possible to set i e lateral Erea M G steering angle suspension travel etc to zero Parameters for linear conversion In the Logged Data window double click on the EE uments ues Binary values Real values Binary values Real values channel you want to configure for resetting and 0 655535 0 655355 the Channel Property Window opens Tick the box for 0 needed You can configure the logged channel data independently of the original settings in the database Enter the requested data values in the Real values window and click the centre OK button When completed click OK to confirm changes and to return to the logger setup screen E g the steering might be showing 12 when the wheel is straight so enter 0 Datalogger DashBoard Map manag mE To set the newly configured channels to 0 select Set Channels 0 from the datalogger menu on the main ECT Toolbar Make EE sure the correct ECU is selected and that the channels are Convert data to Text Format listed Convert LOG File bo 2D Format Click OK to set channel values to 0 a
53. ile it is loaded in the editor on your PC s hard disk Click on FILE and then SAVE TO FILE AS If you type a name of an existing file you will be asked to confirm overwriting the old file lf you are working offline you can save the file whenever you want to Click FILE then SAVE TO FILE to overwrite the existing file or SAVE TO FILE AS to create a new file Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 51 of 67 Ocr Control Systems Ole Buhl Racing UK Ltd 9 WORKING WITH THE DISPLAY MANAGER 9 1 DISPLAYING ENGINE DATA You can work online with the ECU map manager and simultaneous display engine data on a customised display screen We supply several preconfigured display screens with the ECT software and you can easily design a new display screen to suit your needs These screens can apart from displaying any measured or calculated engine parameter also include LED s used as warning lights and potentiometers Potentiometers are intended to be an aid during the engine mapping They express variables such as injection trim spark advance offset boost pressure lambda target etc 5501 1min bw 31 3 Learn Trim MAP E 1 OO mbar RHeaterLambdal 1310 7 Ohm Air Temp 25 C d Water Temp fl C a Oil Temp
54. ion or percentage correction e Press Enter to open the property window Type a new value which will be applied on all marked cells Press Enter to confirm or e Use the keyboard or display buttons to increase or to decrease the cell values or e Type an offset value positive or negative in the window CORRECTION Press Enter to confirm or e Type a percentage correction positive or negative in the Window CORRECTION Press Enter to confirm When a cell s value is changed the background colour changes to red to indicate a new value To cancel all changes press F11 Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 37 of 67 DESTA contro systems Ole Buhl Racing UK Ltd lf you want to store this value in your map remember to press F8 This sends the information to the ECU and stores it in the map on your computer The changes however are not saved on your computer until you save the map Remember to give the altered map a new name if you wish to keep the original 6 9 MODIFY A MAP A map links values of two measured channels to a calculated parameter with a variable output which can be i e injection pulse width spark advance degrees solenoid valve duty cycles offsets or multiplication factors Double click on the text line of t
55. is section you can select the type of ECU currently used A window on the icon bar shows the actual ECU communication protocol selected i e EURO4 305 Within PROFILES PROFILES MANAGEMENT can be accessed here you can open new profiles copy delete update load new and reassign devices 3 3 DISPLAYS You can create screens displaying any ECU parameter measured and calculated for each type of ECU A screen can display any number of channels in any size font and colour Data can be displayed or linked as e Data windows e LED red or green colours e Trim potentiometers for example for global trims of fuel spark phase etc These potentiometers can be controlled by software your mouse or by our Active Mapping Controller This is a mapping controller having 6 individually programmable potentiometers plus a STORE button e Strip charts giving a graphic visualisation of up to 5 channels simultaneously e Read or write directly into ECU memory locations requires a dedicated license Using the Displays Manager you can open a display create a new display copy a display file delete a display and rename a display Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 14 of 67 Ocr Control Systems Ole Buhl Racing UK Ltd Refer to the latter parts of
56. isting file name again overwriting the existing file Finally you will be asked if you want to mix the map with the learn map Select YES or NO Note To establish which maps are loaded in the ECU connect to it and open any display screen Right click on any part of the grey area inside the screen and then select Device Information from the pop up menu 4 5 TRANSMIT SETUP MAP Setup Map Transmission Select Device Select Directory E12 356 REITER E BM_PRELOAD e eil This section is not relevant for Euro 1 The EURO12 407 PRIDE EURO12 409 EUROE 407 setup map is used to configure the ECU to the EE Se Eurol2 402 edt J system setup of your engine sensors being used triggering configuration etc Since each version of ECU s uses a different Select Map communication protocol it is important to specify EE Send Map to ECU to which ECU you want to transmit the ECU setup map Select the correct type of ECU in the upper left window Select Device o h Next specify in which data directory the map is located Make sure the correct directory is highlighted in the upper right corner Select Directory The ECU setup maps are listed in the Select Map section Click on the square box to select the desired map Click on SEND MAP to ECU to transmit the ECU setup map to the ECU Click OK to confirm Reset ECU OK Setup Map Upload Select Device Select Directory E12 356 REITER c IBM_PRELOAD
57. k to display browse Search for the first display database file located in USER directory you want to allocate A database file is located in the WIN directory for each display layout Click on the file name and then click Open The display is now added to the display page To add additional pages proceed by clicking Insert Link again and search for files Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 53 of 67 Ocr Control Systems Ole Buhl Racing UK Ltd 9 4 COPY DISPLAY GROUP You can copy an existing display group by clicking on Load Group Select the display group you want to copy and click OK Type the name of the copied display group and confirm by clicking on OK 9 5 CREATE NEW DISPLAY Load the Display Manager The first available display layout is highlighted in section Displays To open this display click Open Create New To create a new display layout from scratch type a new name in Select Display from List overwriting the proposed existing layout Then click Open Create New You will be asked to confirm the creation of the new layout Click OK to confirm and to open it 9 6 EDIT A DISPLAY SCREEN Click your right mouse button and select ENABLE EDIT MODE or Double click in any unused area of the display window to enable
58. lting us first Click OK to add this new LED to your display screen 9 10 ADD POTENTIOMETER Since each version of ECU s uses a different communication protocol it is important to specify from which ECU you want to display data Click on the arrow in SELECT TABLE to select the ECU type and version you are using Scroll through the available channels in search of your desired potentiometer Ole Buhl Racing UK Property Window Can Table Channel Selection Select Table EURO6 402 v Default channel name Absolute lap AcceCntlOLCond AEd MAP SFdATPS String expression sought Default channel name Default description Custom description Absolute Number of Laps Static Tab Address on display 528 Property Window Led Properties Range Colour e Green C Red MIN lt x M iai WR D x lt MIN x gt MAX Text Text c Property Window Can Table Channel Selection Select Table EURO6 402 D Advance AMC Trim lan AMC Trim lgn2 AMC Trim Jon AMC Trim land AME Trim lan String expression sought Default chanel are ERED Custom channel name Advance Default description Custom description Spark Advance AMC Correction Static Tab Address on display 135 Lid Can Setting Control Conversion OK Exit Can Setting Conversion OK Exit Can Setting Control Conversion OK Exit Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88
59. map a1 1a a4 4 nable dashboard setup nable output diagnosis Ignore possible presence of crypting dongle Select your preferred options 4 2 ECU COMMS You can transmit engine maps ECU setup maps ECU firmware and learn maps from your PC to any of our systems Maps can be received from the ECU s to your PC as well Engine maps in the ECU can be password protected from non authorised access Specially encrypted ECU s are also available for special applications This section also gives access to the learn system and to resetting the diagnostic memories and timers 4 3 TRANSMIT Select Device Select Directory E12 356 REITER ETB 0035 EURO JEUROT2407 EURO12 407 PRIDE EURO12 409 EURO1 430 v to which ECU you want to transmit the Map Select Kernel Firmware FPGA Test MI ElZ2 402 BIN 1171072004 23 46 248278 Byte RE to Select the correct type of ECU in the upper left Sc window Select Device by ensuring the box has A c IBM_PRELOAD D Since each version of ECU s uses a different communication protocol it is important to specify lt Q Eurol 2 400 Eurol2 402 edt Select Map f 3 WJ ENG402 TAB 12 10 2004 01 24 76466 Byte a tick In It Next specify in which data directory PRIDE 1 TAB 12 11 2004 05 47 76466 Byte Send Map to ECU the map is located Make sure the correct directory is highlighted in the upper right corner _ Select Directory Exit
60. n Now open the throttle valve fully and click OK to set the maximum position The system will confirm click OK Do not move the throttle valve before you have confirmed the position Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 26 of 67 Ocr Control Systems Ole Buhl Racing UK Ltd 5 LOG INTERFACE All ECU s but Euro 1 Euro 2 features an on board data logger with a memory capacity of 8 16 Mb It can log any data from any ECU input or data calculated by the ECU Sampling rates can be selected individually for each channel logged An analysis software package is supplied by 2D allowing the user to visualise the logged data 5 1 SETTINGS To access the data logger options click on LOG INTERFACE in the E Iw Enable factory name ECT Main menu When the window EFI LOG INTERFACE opens ees click MAIN and then SETTINGS a iterii ional Select your preferred options but always select 2D Windows 5 2 RECEIVE Click DATALOGGER and then RECEIVE Logger Download elect Device S Data can be downloaded at a typical rate of 2 5 Mb per euro een New Even EUROT aa En 809 DeLete Event EURO6 407 196 1909 BR CROFT EXHTMP LDDFILES MASS OFFICE minute Create a directory by clicking on NEW EVENT SUZ P2 Size bytes
61. n in a clear area of a display screen select Min timer interval lt 0 1 Fastest 0 c Timein File Output order for Log Store and Strip Chart if you want to alter the Device ID in file acquisition order Descriptions Press F3 or click on the Log Icon to open the Log Property window Click to select a new log file or to append data to an existing file Set the Log Timer to zero for maximum sampling rate ECT EFI Communication Tool supported by your PC s parallel port File Data Display Learn Map manager Windows 7 ZE Ready E F2 Store Grouse d F4 Pot Off Ke Data is stored in a comma file which can be analysed in either Excel or converted into a 2D data file You can type a brief description of the test Click OK to start logging data Press F3 again to stop logging The Icon on the main toolbar shows the logging status Refer to section 1 4 5 3 Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 60 of 67 Ocr Control Systems Ole Buhl Racing UK Ltd 9 21 ECU STATUS Use a display screen to check the status of the ECU in use Click your right mouse button in a clear part of the display screen and then select Device Information A window now opens with information on e ECU version e Firmware version e Maps loaded Ol
62. nd to return to ECT s main screen Note When you Zero a channel the ECU applies an offset to the current settings and recalculates the corrected values in a post processor This leaves the live channel value unchanged and hence you will see no change in its value on a display screen The correction is only applied to the existing values during the logger download Adding a channel or changing a sampling rate the maximum available Log mas time 714803 logging time is displayed in the window LOG MAX TIME In this example data can be logged for 11 hours 39 minutes and 3 seconds Depending on the settings in the ECU setup map the recording either stops when the memory is full or the data is cleared and the recording just continues When you have selected all the channels you wish to log you must define how you want to activate the logger Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 29 of 67 DESTA contro systems Ole Buhl Racing UK Ltd In TRIGGER MODE you can select between Trigger e Disable Logging switched off Trigger Mode Min Switch Channel 2000 Trigger Channel May e Ex Switch Logging is activated by external switch RPM 5000 Delay 1 0 1 e Switch Channel Logging when channel thresholds are true ee ___ e Continuous Logging
63. ng UK Ltd The information logged to your PC will be stored as a comma file in your User folder within the main ECT MOD folder ECT can automatically convert the recorded data to 2D s seg data format Recorded data can therefore be visualised Serial Port Settings Advanced options using 2D s WinaRace data analysis software V Enable leam tools Enable 45 4P menu To enable this feature click Displays When the Property f W Disable Pot after Store Window opens click on Main then Settings and finally kd Enable factor name Advanced Options Tick the box Automatic conversion from LOG ETL file to 2D format hd Automatic conversion from LOG ETL file to 20 format Start logging data from the selected display screen by pressing F3 storing the data to your PC In the Log Property window you have the following options Log Property e Append Last Add new log to existing file Append Last e New File Create a new log file CACORE Cancel e Time In File Add time stamp for each sampling of data M Time in File s Min timer interval lt 0 1 Fastest o1 sec e Min timer interval Set sampling interval in seconds or mses HH MM 55 000 specify 0 for fastest possible sampling rate Device ID in file replacement string if occurs in a string var e Device ID in file ECU status is included in log file Descriptions e Description Add your comments to this log file fC
64. ns within the fuel injection self learn map for all ECU s and stored corrections within the boost pressure map and the ignition map for Euro 6 and Euro 12 Select which type of reset function you require and then select which learn map to reset and click OK Select Device from list v Reset functions 4 15 THROTTLE POSITION CALIBRATION ai Z Select Learn Map 1 ei Reset Min max adjusting procedure 7 S 7 Throttle position learn The Min max adjusting procedure is used to calibrate the range of 1 ear tenpessok 7 J the throttle potentiometer in all ECU s apart from Euro 1 s You can only use this feature if you have selected the manual throttle calculation method in the ECU Setup Map Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 25 of 67 Ocr Control Systems Ole Buhl Racing UK Ltd Before you carry out the calibration use the Analogue display screen to check that the raw data of the potentiometer s working range is within the recommended 50 1 000 bits value as displayed in the TPSI window To adjust the minimum setting make sure any throttle stop screws are backed off fully Click OK adjusting the minimum position The system will confirm click OK Do not move the throttle valve before you have confirmed the positio
65. nstalled on your hard drive Double click on the efiusbcan_drv folder to enter it e Click on the EFIUSBCAN icon The driver will now install e In the Server programme ensure the USB option is selected as shown on the previous page Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 12 of 67 DESTA contro systems Ole Buhl Racing UK Ltd 3 USING ECT With the data files and communication settings finalised its time to configure the ECT Modular programme e Open the ECT Modular programme from the icon on your desktop or from the All Programmes option from the main windows Start button ECT Modular opens as a Gi ECT Main Menu Eg Line Communication Interface setup Device setup Profiles Displays Map Editor Mem Interface LoG Interface Components arrangment Language Exit ES el Ou SIZ RR toolbar at the top of your screen as show below e LINE toggles the default PC communication link between default ON LINE and OFF LINE e COMMUNICATION INTERFACE SETUP gives access to the server address Under normal conditions do not alter this setting e DEVICE SETUP gives access to the system database This is for experienced ECT users only e PROFILES allows you to select between display screens for various ECU versions e DISPLAYS gives you
66. o uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 34 of 67 Oc Control Systems 6 4 AVAILABLE ITEMS Data in the map file is divided into various groups relevant to their function You can scroll though the groups with the arrow keys or mouse When you see the group you were searching for click on it and press Enter or double click it to display its content You can use a speed search too Type the first letter or two of a group i e FU Ole Buhl Racing UK Ltd ECT EFI Communication Tool 550 1 TAB CH File Data Display Leam manager Map manager Windows _ Map loaded from ECU oo Map Information On Line n Pot of vailable items 3D Fuel Spark Advance Maps Boost Control ETB Idle Control ETB Throttle Position Control Filters Fuel Cranking Fuel Cut Off Fuel Individual Injectors Trims Fuel Injection Phase Fuel Limits Fuel Staged Injectors Idle Speed Iqnition Individual Cylinder Trims Iqnition Main Maps Knock Control Lambda Closed Loop Lamhdaa CLinsed Tonn Standard for FUEL The cursor jumps to this group Press Enter or double click to display its content Use the TAB key to move the cursor to the contents of the group or click on the parameter with your mouse The items available in the group are constants calibration tables 1 dimensional arrays and maps 2 dimensional arrays To open a table or
67. of windows 9 16 DISPLAY LAYOUT DESCRIPTION To change the display description first select a layout in Select Display from List from the main display manager menu Change the text in Descriptions Click Update Description to save changes Click Exit to return to main menu 9 17 COPY DISPLAY To copy an existing screen display click Copy Display Browse through the files and directories to find the display layout database file to copy Click on the file to mark it and then click Open Type a name for the copied file and press Enter Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 59 of 67 DESTA contro systems Ole Buhl Racing UK Ltd 9 18 RENAME DISPLAY To rename a display first select a layout in Select Display from List Click Rename Display type a new name for the display and click OK The display will now appear in the display list under its new name 9 19 DELETE DISPLAY To delete a display first select a layout in Select Display from List Click Delete and click OK to confirm The display will be deleted from your PC s hard disk 9 20 LOGGING DATA All data displayed on a selected display screen can be logged in a file on your PC s hard disk Log Property f Append Last f New File Cancel eae Click your right mouse butto
68. on OAEFB37B00200 yellow label 2 EFLO6 Plastic USB interface released 06 2008 3 EFPO2 USB CAN opto isolated interface released 09 2012 1 1 INSTALLATION ECT Modular 3 7 23 should be installed either from a CD supplied by Ole Buhl Racing or having downloaded the setup file from www obr uk com under Support Software If installing the software from an OBR supplied disc you will see the following folders by exploring the disc 1 2D Handbooks Handbooks for 2D products 2D licenses A guide to the difference license options available for 2D Winarace software 2D Products A guide to all of 2D s latest motorsport products Dash Data logging files Configuration files for 2D s range of loggers and dashboards ECU Data files Configuration files for EFI ECU s EFI Technology ECU A guide to all the EFI ECU s available EFI SetupHelper Automatic software installer PCM Installation OBR s power control module software Pricelist 2012 OBR s 2012 price list 0 SetupDepot Individual EFI software installations manual installation 1 sr Ee ME a E WinARace 2006 1 2D s free version of its popular WinARace software to be used with ECU internal data logging You will also find last minute updates for the program and an installation and registration instruction file j setuphelper To start installing ECU modular 3 7 23 insert the CD in your CD drive If you have selected to explore the di
69. on parameters Gain 1 Offset 1 Gain 2 Offset 2 nn nh Gei Display Format Conversion type Unit oun DEC Vmin Number from 1 to 9 0 Number from 0 to 9 Point Decimal separator jw Unit Enable Click OK to add this new channel to your display screen Ole Buhl Racing UK Ltd Roughwood House Highwood Nr Ringwood Hampshire BH24 3LE United Kingdom Telephone 44 0 1425 47 88 22 Telefax 44 0 1425 47 88 66 sales obr motorsport co uk www obr motorsport co uk Page 55 of 67 Oc Control Systems 9 9 ADD LED Since each version of ECU s uses a different communication protocol it is important to specify from which ECU you want to display data Click on the arrow in SELECT TABLE to select the ECU type and version you are using Scroll through the available channels in search of your desired channel To ease the search type the name of the channel you are looking for in CHANNEL and press Enter To select the channel click on it when it appears Click on CONTROL to access the LED configuration Click on either GREEN or RED to select the colour of the LED Click to select the strategy for the LED Click CONVERSION to access the channel data configuration Click UNIT ENABLE to enable or disable the channel engineering unit DISPLAY FORMAT changes the number of digits before and after the decimal point IMPORTANT Do NOT alter any other data in this section without consu
70. on sought its name in the STRING aa A E CAN Data Addr Description User Mame Factory Name EXPRESSION and press Enter You e Engine Revolutions RPM Remo can also search for it manually using Data Type Conversion Type Default Value Display Format Unit M DEC 0 H nn Amt the slider bar Gain Offset 1 Gain z Offset 2 Dlogger Dog mas Hz Bytes Min graph val blas graph val Cs Cs Km db bm mm Stack Datapro settings Channel Name Channel Number User Level You can change the USER NAME and ESPD E No PIN Code 15 default channels H Dam Offset 1 Gain 2 Offset 2 Units Code requirements Do NOT change the FACTORY Mew Delete last Data Result Number of Bytes E E NAME E E xik Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 64 of 67 Oc i Control Systems Ole Buhl Racing UK Ltd If you want to change the specification of a channel to suit a different application and input the gains and offsets have to be altered Please contact us before changing any settings within DEVICE SETUP or any of the gain or offset parameters For Euro 6 and 12 users a channel can be logged by the onboard data logger if it has a tick in the DLOGGER box The channel s number of bytes and the maximum allowed samplin
71. orsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 66 of 67 Ocr Control Systems Ole Buhl Racing UK Ltd e The stored self learn map can be reset from the main menu selecting LEARN and then LEARN FUNCTIONS Furthermore switching the VBATT KEY Ignition on without starting the engine fully open and close the throttle valve 3 times and then wait in excess of 20 seconds without starting the engine also resets the learn map e The learn map is created in RAM Switching VBATT KEY off but leaving the VBATT DIR isolator on stores data from RAM into flash e Downloading an engine map from any location in the ECU allows you to mix a created learn map with the base fuel map Select YES when asked Perform corrections based on Learn Map e Remember to reset the learn map when you have transmitted a new engine map with a corrected base fuel map to the ECU Uor For the full range of OBR products support and services visit us online at Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 67 of 67
72. ort co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 24 of 67 DESTA contro systems Ole Buhl Racing UK Ltd 4 12 RECEIVE FUEL LEARN Select Device Select Directory 9 c IBM_PRELOAD bd E12 356 REITER ETB 0035 EURO EURO12 407 EURO12 407 PRIDE EURO12 409 EURO1 430 EURO6 407 ajEURO96 310 Since each version of ECU s uses a different communication protocol it is important to specify from which ECU you want to receive the map Select the correct type of ECU in the upper left window Select Device Upload ECU gt PC Next specify the data directory in which you want the map to be located Make sure the correct directory is highlighted in the upper right corner Select Directory In section Select Source Map select from which map location you want to download the learn map Click UPLOAD ECU PC to start receiving the map When are asked for a file name for the map you can choose any key combination except lt space gt and You may choose to use the existing file name again overwriting the existing file 4 13 LEARN FUNCTIONS This section gives access to various functions of the learn system Since each version of ECU s uses a different communication protocol it is important to specify with which ECU you want to communicate Select the correct type of ECU in the upper left window Select Device from list 4 14 RESET You can reset the stored correctio
73. r engine map too Load the map and mark the map cells in the new map to be replaced by the new data Press CTRL V to paste the new data Click or press F8 to save the changes or F11 to discard changes If you have to copy complete sections from one map to another it is possible to export whole calibration tables and maps by the click of a single button From the main menu open the map editor and load a map from either the ECU or your PC s hard disk Open the editor once again and load a second map Click on WINDOWS and click on TILE VERTICAL Now go to the group from which you want to export data and open the calibration table or the map Repeat for the procedure for the second map Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 49 of 67 DESTA contro systems Ole Buhl Racing UK Ltd When you see the same map in both the left and right side of the screen e g Fuel injection map click the EXPORT or EXP Data tabs on the map from which you want to export the data The complete map including breakpoints is now being copied to the other map All copied values if different from the imported map are highlighted in red To undo or discard changes select the map which has imported data and click or press F11 To then save changes click or press
74. r motorsport co uk DESTA contro systems Ole Buhl Racing UK Ltd The installer will then start to install the first programme ECT Modular 3 7 23 You will then be asked to select which language you require English or Italian Installer Language CG Please select a language ECT v Next you are given the option of installing a desktop Icon ECT Setup Choose Components Choose which features of ECT you want to install TECHNOLOGY Check the components you want to install and uncheck the components you don t want to install Click Next to continue Select components to install EET ECT Shortcuts Description Space required 15 3MB L ap L zeg You are then asked to specify the destination folder for the installation If you have had any previous versions of ECT or ECT Modular installed then select C ECT ECT modular will then work with your existing Editor Device and User folders If this is a fresh installation you have the option to select suggested installation path Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 6 of 67 DESTA corro systems Ole Buhl Racing UK Ltd ECT Setup H m Choose Install Location Choose the folder in which to install ECT TECHNOLOGY Setup will install ECT in the followin
75. sc select the setuphelper icon from the CD under EFl_SetupHelper or as downloaded from the website and select Run Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 4 of 67 CSR contro systems Ole Buhl Racing UK Ltd This will launch the Setup Helper shown below Select Next and then ensure you have all three programmes selected as shown Welcome EFI Setup Helper CL tility to facilitate the installation of EFI s applications om Vig D TECHNOLOGY Press Nest to continue ay EH Setup Helper Selection List of Setup JW ECT Modulare v 3 7 23 0 w ECU Communication Server wv 2 6 13 0 h EFI Technology Drivers v 1 2 2 0 W PseudoProgrammer v 0 5 11 1 zs ores Select Next again You will then get a summary of what will be installed Click Next E EFI Setup Helper Summary The following Setup will be installed EFI Technology Drivers v 1 2 2 0 ECT Modulare v 3 230 ECU Communication Server v 2 6 13 0 Pseudo Programmer w 0 5 11 1 Cancel Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 Roughwood House Highwood Telefax 44 0 1425 47 88 66 Nr Ringwood Hampshire BH24 3LE United Kingdom Page 5 of 67 sales obr motorsport co uk www ob
76. the new map To load a map working online with the ECU click on Map Manager and an select ECU Setup Map Look for the small square next to Map loaded from EC U lap loaded from El Device ooo Map sl General Map Information vallable items Click on the arrow in the DEVICE window and click on the ECU configuration you are using Click on the arrow in the MAP window and select the map Loading a map from your PC click on ECU SETUP MAP then click on FILE and finally click on LOAD FROM FILE Make sure the window LOOK IN displays the data directory related to the ECU in use Click on the map and then click OPEN An ECU setup map consists of 3 files all with the same name but different extensions e One without extension containing information about required descriptor file commentary file notepad file and data file e One with NTP extension a notepad file in which you can include information about the engine sensors etc e One with ECF extension the actual data file If the ECT cannot find the file without extension it has to ask you which descriptor file you want to load The editor uses the descriptor file to visualise the data from the engine map The descriptor file is given a unique name identifying it to the type and version of ECU The ECU setup map descriptor file extension is CDS Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Tele
77. ting Font INS Sans Serif E Fore Color es Back Color Cd Tie Foxe Cle BR Conversion i Ss En D 2 Orientation Property OK Name UP Unit DOWN jw Name LEFT jw Unit RIGHT Exit the data Property Window Can T able Channel Selection Select Table EURO6 402 Default channel name Static Tab Addr EI Absolute Run Can Setting General Conversion AcceCntlOLCond AEd MAP AF AITPS String expression sought Default channel name Custom channel name Absolute lap Absolute Number of Laps Static Tab Address on display 520 Default description Custom description Click on GENERAL to change the text and background colour font style and size Click NAME UP if you want the channel name on top of the data Click NAME LEFT if you want the name to the left of the data Click UNIT DOWN if you want the channel unit on top of Click UNIT RIGHT if you want the unit to the right of the data Click CONVERSION to access the channel data Property Window CO nfig u ratio n Conversion Parameters Default conversion parameters __CanSeting Click UNIT ENABLE to enable or disable the channel Gain 1 Offset 1 ganz Offset 2 General engineering unit Def conv type Def unit name DISPLAY FORMAT changes the number of digits before and after the decimal point IMPORTANT Do NOT alter any other data in this section without consulting us first DEI Custom conversi
78. unication protocol it is important to specify eUROT 430 EURO6 407 from which ECU you want to receive the map Select the correct type of ECU in the upper left window Select Device Next specify the data Select Descriptor vw Upload ECU gt PC E12SD402 directory in which you want the map to be located Make sure the correct directory is highlighted in the upper right corner Select Directory In Select Descriptor you must select which descriptor file is selected The editor uses the descriptor file to visualise the data from the engine map The descriptor file is given a unique name identifying it to the type and version of ECU and whether the engine load is throttle based AN or pressure based SD In the section Select Source Map select from which map location you want to download the engine map Click UPLOAD ECU PC to start receiving the map You may be prompted for a password Type the correct password to proceed If you do not know the password you cannot receive the Map Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 21 of 67 DESTA contro systems Ole Buhl Racing UK Ltd When are asked for a file name for the map you can choose any key combination except lt space gt and You may choose to use the ex
79. ured in each fuel map breakpoint is adjusted automatically until the measured lambda value corresponds with the target value Adjustments are stored in a separate map called the learn map in the ECU This map has identical breakpoints to the fuel map but instead of listing pulse width the corrections are listed as multiplication factors between 0 and 2 where 1 is the neutral value Learn maps can be downloaded to the PC for analysis and transmitted back to the ECU Note Learn files save with the file extension LRN 4 11 TRANSMIT LEARN Since each version of ECU s uses a different communication protocol it is important to specify to which ECU you want to transmit the learn map Select Device Select Directory E12 356 REITER Sc lBMPRELOAD el ETB 0035 1a Select the correct type of ECU in the upper left window EDRO12407 ona Select Device see i Bruno ien Select Learn Map File Next specify in which data directory the map is located SE ST Make sure the correct directory is highlighted in the upper Select Destination Learn Map right corner Select Directory Exit The learn maps are listed in the Select Map section Click on the square box to select the desired map Click on TRANSMIT to transmit the learn map to the ECU Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsp
80. when ECU is switched ON The triggering channel must be one of the logged channels and is most commonly selected as either the engine RPM or the car speed In MIN and MAX you specify the activation and de activation values DELAY sets in 1 10 of a second the delay for activation and de activation of the logger When you have created a logger setup you can save it to a file Click on FILE then SAVE and type a file name Click OK to save the file These files are saved in DEVICE DEV directory for the ECU used To transmit the logger setup to the ECU click on Update in ECU When the ECU logger has been programmed this message appears Logger setup successfully updated in ECU 5 4 CLEARING LOGGER MEMORY When you transmit a configuration file to the logger the memory will be cleared 5 5 CONVERT LOGGED DISPLAY DATA TO 2D FORMAT Data can also be logged directly onto your PC Working with any display screen you can store data from all windows on the screen into a file on your PC s hard drive by pressing F3 ECT EFl Communication Tool Fie Data Display Learn Map manag Windows ZE On Line Ga a F4Poat Of F5 Leam default On LE Engine On Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 30 of 67 Ocr Control Systems Ole Buhl Raci
81. y buttons to increase or to decrease the cell values or e Type an offset value positive or negative in the window CORRECTION Press Enter to confirm or e Type a percentage correction positive or negative in the Window CORRECTION Press Enter to confirm Click F11 to discard changes or F8 to save the changes Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 46 of 67 DESTA contro systems Ole Buhl Racing UK Ltd 6 19 GRAPHIC DISPLAY PROPERTY Double click on either the horizontal or the vertical breakpoints to bring up the graphic Graph properties display property window You can personalise the meee lem layout of the display by modifying EE nn e Background colour Cursor color e Grid colour Line color e Cursor colour Highl line color e Line colour Highl line thickness E e Highlighted line colour p Cancel e Highlighted line thickness Click the button with the function required and select the desired colour Click OK to confirm 7 PRINT To print the contents of a map click on FILE and then click on PRINT The print function allows map details to be printed directly or imported to a file see Output device You are also given the option of what you wish to print To print the complete map select all the boxes i e
82. z GC ECT Editor EJ Euro6 400 Euro6 407 ech C System EURO12 407 EURO12 407 PRIDE wi ee EUROE 407 4 6 RECEIVE SETUP MAP This section is not relevant for Euro 1 Since each version of ECU s uses a different communication protocol it is important to Teor specify from which ECU you want to receive the OS Fee map Select the correct type of ECU in the upper left window Select Device Next specify Ole Buhl Racing UK Ltd Telephone 44 0 1425 47 88 22 sales obr motorsport co uk Roughwood House Highwood Telefax 44 0 1425 47 88 66 www obr motorsport co uk Nr Ringwood Hampshire BH24 3LE United Kingdom Page 22 of 67 DESTA contro systems Ole Buhl Racing UK Ltd the data directory in which you want the map to be located Make sure the correct directory is highlighted in the upper right corner Select Directory In Select Descriptor you must select which descriptor file is selected The editor uses the descriptor file to visualise the data from the engine map Click UPLOAD ECU gt PC to start receiving the map When are asked for a file name for the map you can choose any key combination except lt space gt and You may choose to use the existing file name again overwriting the existing file Diagnostic data Reset me i 4 7 RESET DIAGNOSTIC DATA Select Device This section is relevant for Euro 1 and Euro 96 ECU s only To reset the diagnostic m

User Manual - OBR

Contents

Download Pdf Manuals

Related Search

Related Contents