SL1524LD LED Street Light Controller (Waterproof) User`s manual
Contents
1. 100 100 5 The setup range of every time interval power and default before factory shipment Controller distinguishes daytime or night from checking open circuit voltage of solar panel When voltage is below 2 5V which lasts 15seconds it is 12V system and we regard it as sunset When voltage is over 2 5V 1V which lasts 15seconds it is regarded as sunrise 24V x 2 Consumers can setup different light control identification point according to different solar panel and using circumstance Announcement 1 L1524D is used for solar panel which is maximum output voltage is 50V battery maximum voltage is 35V The load will be off when its voltage on battery is over 16 5V 24V x 2 SL1524LD built in big power and step up LED driver please be sure that LED module number when LED connects in series LED number range should be 5 15pcs for 12V system and maximum power is 60W When LED module is in series and its numbers are in 10 15pcs maximum power is 120W The more LED module connects in series the less bright they are If LED numbers are too less which will cause LED lamp damaged and not constant System voltage LED numbers Max power 12V 5 15 60W 24V 10 15 120W SL1524LD driver default is 1 5A please setup LED driver current which you need before connection Otherwise If current is too big it will damage LED module LED current is determined by LED connection in series and in parallel2. For example lamp cap is made up of 30pcs 1W Led if it is for 12V system Led number in series should be within 5 15pcs The LED number in series will choose even number in order to make lamp cap look symmetrical and here are two connection ways a Distributing into three units connects 10pcs LED in series for each unit then connect 3 units in parallel Every units of LED current is 300Ma total current of LED cap is 3 300mA 900 mA b Distributing into five units connects 6pcs LED in series for each unit then connects five units in parallel LED current is 300Ma for each unit total current of LED cap is 5 300mA 1500 mA We can see total current is different after different connection in series or in parallel We must confirm LED connection before installing lamp cap and set up driver rated current through programming device then connects LED cap Technical data k SS SL1524LD Current range Battery voltage 12V 24V Auto Input Solar panel voltage lt 50V Max charging current 10A LED driver max output voltage 55V LED driver max output power 12V 60W__ 24V 120W Output LED driver output current 1 5A 0 3A 3A LED driver converting efficiency 90 95 Battery reverse protection Yes Battery overvoltage protection 16 5Vx1 x2 LED driver output short circuit protection Nes Protection Solar panel reverse protection Yes Battery reverse discharging protec
3. time interval for PWM light adjustment which makes LED Street light more intelligent and saves much electricity 6 With temperature probe outside temperature compensation is more accurate 7 More advanced charging and discharging controlling calculation which increases using efficiency of solar panel and extends battery longevity 8 High power density all is aluminum shell volume is smaller but better performance 9 SL1524LD has infrared wireless receiving and sending function which can achieve wireless programming to controller by the SLO2 10 Consumers can adjust LED driver current with SLO2 programming device and no need to make specially Note Remote is optional part to customer If users want to change default parameters Please buy remote or let us know detailed demand before factory production Installation diagram O O a ga SL1524LD Solar Charge Controller Boost LED Driver Inside Max Output Voltage 55V Max Output Current 3A ww 0Z 9 ww 0p 69 90 00 mm 120 00 mm 1 Controller outer size 120x69 4x20 5 mm Installing hole diameter 3 2 mm 2 Confirming system voltage is 12V or 24V before connecting Checking all wires and avoid controller being damaged because of short circuit then connect controller according to diagram 3 First please connect battery positive and negative battery indicator will be lighting if right connection lf battery indic
4. SL1524LD LED Street Light Controller Waterproof User s manual Dear users Thanks for using the product Please read the manual carefully before using it SL1524LD Controller combined big power and step up LED driver with water resistant street light controller which makes the installation use and maintenance of LED Street light system more convenient which makes system work more reliable Executive infrared programming device SLO2 can check and set all technical data of controller SLO2 programming remote can communicate with controller by infrared and finish the setting of controller floating LED working current LED working time LED s working power of different time While finishing setting parameter on SLO2 pressing the button Send one time and finishing controller parameter setting It does improve the efficiency of LED Street light system For detailed function information of SLO2 please read its manual SL1524LD Function 1 Epoxy resin sealing processing which increased its nature of being anti thrown shock resistant waterproof damp proof anti corrosive waterproof and achieve IP68 level 1 System voltage is 12 24V automatically identification 2 Anti reverse protection Intelligent open circuit protection short circuit protection of LED driver 4 SL1524LD built in high precision step up LED driver which can drive Max output voltage 55V Max output power 120W for 24V System Max driving efficiency is 95 5 Four
5. ator does not light please stop operating Please solve problem with reference of malfunction operation 4 Please connect LED module to the load Note Factory default current of LED driver is 1 5A if consumers use LED module which its current is smaller than 1 5A please do not connect LED module with the load you must use infrared programming device SLO2 to reset LED driver current LED driver current its rated value can not be bigger than that of LED module It will damage LED if driver rated current is too big 4 At last connecting solar panel charging indicator will be lighting if it is correct connection which also means battery is charging Blinking means battery is full charged and floated 6 Try to make wire shorter between battery and controller wire current density can not be bigger than Ame 7 SL1524LD Controller s parameter can be amended by SL02 programming device Otherwise LED working time will be 14hrs at the first interval of system default output power is 100 time is OH LED driver current is 1 5A 8 The setup parameter can be sent to controller with Send button on remote The Read button has the function of showing controller s setup parameter current battery voltage solar panel voltage temperature and LED lamp current on SLO2 Status indication and function Indicator Status Function On Solar panel has voltage and it is charing batte
6. earance is not being damaged and we will return or repair after our confirmation to damaged product 4 lf any loss is caused of unreasonable system design or parameter setup we are not responsible for this consequence Fault diagnosis Phenomenon Reason and solution battery is reverse connection or wire connection is loosely Solar panel voltage is bigger than identification Load is not on when sunset charging indicator is till on point of light control please check if solar panel surface is surrounded by powerful sunshine Battery is under voltage load will work after battery charging is full on the second day Please check if LED module is connected Load is not on when sunset load indicator is blinking slowly reversely wire connects off performance and parameter is right or not Please check if solar panel is connected reversely or loosely Battery indicator is not on Load is not on when sunset battery indicator is blinking slowly Charging indicator is not on when there is sunshine Factory Inspection Certificate Production name Solar charge controller Model SL124LD Inspector Production Date See product Origin China The product is quality conformance after inspection before shipment
7. en 3 time interval operation is finished If controller has no dawn lighting function the load will not work and restart until the second night 3 Load works when it is dark minimum step up power is 0 of rated power Maximum step up power is 100 of rated power stepping 10 Load does not work at any time interval if the power sets to 0 If load power sets to 100 the load will light completely in the time interval System default is 100 4 Dawn Lighting means load starts working in N hours before dawn which isn t lighting until sunrise dawn lighting before sunrise which is not fixed time controller will adjusted automatically according to time at night in different season It will take 3 days for controller to identify the time before dawn Dawn lighting function is not so exact before the time If you don t use dawn lighting function please set operating time into 00h Setup data Setup time range Default Operating time at the first segment in the evening O1h 15h 14h Operating power at the ist time segment in the 00 100 100 evening Operating time at the 2nd time segment in the evening 00h 14 h 00 h Operating power at the 2nd time interval in the evening 00 100 100 Operating time at the 3rd time interval in the evening 00h 14 h 00 h Operating power at the 3rd time interval in the evening 00 100 100 Operating time from dawn 00h 14 h 00 h Operating power from dawn 00
8. ry Of Solar panel voltage is low or O voltage or reverse rial PY Indicator connection Blinking slowly Battery is floating charging On Battery works normally H B Off Battery disconnected or battery reversely connected attery meag Blinking slowly Battery is under voltage Blinking fast Controller is over voltage On Load is working normally LED dri ae Off Load is off indicator Blinking slowly Load is open circuit Note When receiving and sending data load indicator is used for indicating receiving and sending status Working mode introduction Load is distributed 4 time interval to work when it is sunset Every time interval and power can be set freely by SL02 programming device diagram is as below gt first period dawn gi ne secdnd period 0 night aytime From daytime to night 1 Minimum time is 00h and maximum time is 14h system default for first time interval is 14Hrs other interval is 00h If setup time is more than that of the whole night Even if the setup time does not finish and the load will be off when it is sunrise Any time interval will be set to 00h and move to next time interval directly If setup value at the 1st interval is over 14Hrs and it will show 15Hrs and load is not controlled by sunshine when entering into universal controller mode The load has output in 24hrs when battery voltage is enough 2 In the evening the load will be off wh
9. tion ug Under voltage protection 11 2V x2 24V 25 C 9V 12V Under voltage resumption 12 6V x2 24V 25 C 11 7V 13 3V Standby loss 12Vs11mA 24VS11mMA Float charging voltage 13 8V x2 24V 25 C 13V 15V Add 0 6V on the Absorbing charging voltage 14 4V x2 24V 25 C basis of float charging Charging control voltage o Others and R a G samovicell e Light control identification voltage Night 2 5V Daytime 3 5V x2 24V 1V 10V Light control identification time 15sec Working temperature range 30 C 60 C Protection grade IP68 Controller dimension 120mmx69 4 mmx20 5mm Net Weight 2759 Warranty 1 e We guarantee to replace return and repair controller in 7days after sales e We guarantee to repair and replace in a month after sales e We guarantee to repair controller in a year after sales 2 If itis unable to confirm using date the warranty period is 18months from factory shipment it is not free of charge if beyond warranty period Using our company product consumers can share on premium service all the time no time limit 3 If the reason of damaged controller is as following mentioned controller maintenance is not free e Not to follow user s manual to operate e Beyond product using standard technical data eBeing repaired or remade by consumers themselves e The parts are old because of bad circumstance e Moving shipping or storing in wrong way eFor returned replaced and repaired service we demand that controller app
Download Pdf Manuals
Related Search