Probasics Zzz-PAP Heated Humidifier
Contents
1. eeeeeeeeeeeereeeen PMI WARRANTS ITS PRODUCTS TO THE ORIGINAL PURCHASER TO BE FREE FROM DEFECTS IN 8 Technical Description MATERIAL AND WORKMANSHIP FOR ONE YEAR IF WITHIN SUCH WARRANTY PERIOD ANY SUCH PRODUCT SHALL BE PROVEN TO BE DEFECTIVE SUCH PRODUCT SHALL BE REPAIRED OR REPLACED AT PMI S OPTION THIS WARRENTY DOES NTO INCLUDE ANY LABOR OR SHIPPING CHARGES INCURRED IN REPLACEMENT PART INSTALLATION OR REPAIR OF ANY SUCH PRODUCT PMI S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY UNDER THIS WARRANTY SHALL BE LIMITED TO SUCH REPAIR AND OR REPLACEMENT FOR WARRANTY SERVICE PLEASE CONTACT THE DEALER FROM WHOM YOU PURCHASED YOU PMI PRODUCT IN THE EVENT YOU DO NOT RECEIVE SATISFACTORY WARRANTY SERVICE PLEASE WRITE DIRECTLY TO PMI AT THE ADDRESS ON THE BACK PAGE PROVIDE DEALER S NAME ADDRESS MODEL NUMBER DATE OF PURCHASE INDICATE NATURE OF THE DEFECT AND IF THE PRODUCT IS SEARIALIZED INDICATE THE SERIAL NUMBER PMI WILL USE A RETURN AUTHORIZATION THE DEFECTIVE UNIT OR PARTS MUST BE RETURNED FOR WARRANTY INSPECTION USING THE SERIAL NUMBER WHEN APPLICABLE AS INDENTIFICATION WITHIN 30 DAYS OF RETURN AUTHORIZATION DATE DO NOT RETURN PRODUCTS TO PMI WITHOUT PRIOR CONSENT C O D SHIPMENTS WILL BE REFUSED PLEASE REPAY SHIPPING CHARGES IMPORTANT SAFEGUARDS SAVE THESE INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING DANGER To reduce the risk of electrocution Always press the power switch the rear of the humidi2. F 2 approximately 102 F 3 approximately 109 F 4 approximately 117 F 5 approximately 124 F 6 approximately 140 F The system is ready for use Consult the CPAP user s manual for operating instructions Danger In order to avoid the destruction or damage to the CPAP equipment or even the hazard of electric shock when the water chamber is connected to the outlet port of CPAP DO NOT fill water from the outlet port of the water chamber Users should not overfill the water chamber Always ensure the water level is no higher than the marking for maximum volume 5 Cleaning 5 1 Heater Clean the heated humidifier base by wiping it with a damp cloth Allow the heater base to air dry before connecting the power cord Inspect the heater and power cord for any damage and replace it if necessary 5 2 Water Chamber 1 Power off the device and allow the heater and water to cool 2 Disconnect the flexible tubing from the water chamber Press down on the water chamber and slide it out of the heater Empty the remaining water 3 Use the extraction tool to remove the chamber base Match the indent on the extraction tool to the remark on the water chamber Use the dotted line on the tool as the pivot and flip it over to remove the base 4 E 4 Usea mild detergent to wash all the chamber parts Rinse all the parts with clear water and allow them to air dry components are also dishwasher safe 5 All items of the chamb
3. which the other device s are connected Consult your homecare provider for help This system has been tested and compliance to the following volunteer standards FDA 1 2 Intended use The Zzz PAP Integrated Heated Humidifier is for use with the Zzz PAP Mini CPAP system It has been designed to increase the humidity of the air from the CPAP therapy relieving the symptoms of dry throat and nasal passages that some people may experience NOTE Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide 6 Service If the heated humidifier malfunctions or doesn t work correctly for any reason contact your homecare provider immediately Never try to open the enclosure of heated humidifier The heated humidifier requires servicing by qualified maintenance personnel 7 Troubleshooting The table below lists troubleshooting solutions for the problems that may happen If the problem persists contact your homecare equipment provider Problem Possible Causes Solutions Power on indicator 1 Power cord not plugged into a 1 Plug in the power cord to a working not lit working AC outlet AC outlet 2 Power switch is not turned on 2 See Setup procedure and turn the 3 PCBor indicator worn out power on 4 Fuse or circuit breaker blown 3 Contact your homecare provider 4 Replace fuse reset circuit breaker or contact an electrician Heater on indicator 1 heat
4. PR BASICS Aq 2u 1 4 1 INOK 104 pepiAoJd mo t gt lt A 3 15 South Main Street Integrated PAM Heated Humidifier Marlboro New Jersey 07746 www pmiusa biz Owner s Manual 666005 6130 V1 0 Probasics Zzz PAP with Integrated Heated Humidifier Model No 9S 003 Series Item No 7501 Please read the instruction manual before use LIMITATIONS AND EXCLUSIONS THE WARRANTY SHALL NOT APPLY TO PROBLEMS ARISING FROM NORMAL WEAR OR FAILURE TO ADHERE TO THE ENCLOSED INSTRUCTIONS IN ADDITION THE FOREGOING WARRANTY SHALL NOT APPLY TO SERIAL NUMBERED PRODUCTS IF THE SERIAL NUMBER HAS BEEN REMOVED OR DEFACED PRODUCTS SUBJECTED TO NEGLIGENCE ACCIDENT IMPROPER OPERATION MAINTANENCE OR STORAGE OR PRODUCTS MODIFIED WITHOUT PMI S EXPRESS WRITTEN CONSENT INCLUDING BUT NOT LIMITED TO MODIFICATION THROUGH THE USE OF UNAUTHORIZED PARTS OR ATTACHMENTS PRODUCTS DAMAGED BY REASON OF REPAIRS MADE TO ANY COMPONENT WITHOUT SPECIFIC CONSENT OF PMI PRODUCTS DAMAGED BY CIRCUMSTANCES BEYOND PMI S CONTROL PRODUCTS REPAIRED BY ANYONE OTHER THAN AN AUTHORIZED PMI DEALERS SUCH EVALUATION SHALL BE SOLELY DETERMINED BY PMI THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES IF ANY INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULR PURPOSE AND SHALL NOT EXTEND BEYONG THE DURATION OF THE EXPRESS WARRANTY PROVIDED HEREIN AND THE REMEDY FOR VIOLA
5. TIONS OF ANY IMPLIED WARRANTY SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT PURSUANT TO THE TERMS CONTAINED HEREIN PMI SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER THIS WARRANTY SHALL BE EXTENDED TO COMPLY WITH STATE PROVINCIAL LAWS AND REQUIREMENTS ALL PRODUCTS LEAVE OUR WAREHOUSEIN BRAND NEW CONDITION IT IS THE CUSTOMER S RESPONSIBILITY TO EXAMINE ALL SHIPMENTS FOR DAMAGE IMMEDIATELY UPON ARRIVAL COUNT THE PACKAGES AND SIGN FOR SAFE DELIVERY SIGN ONLY FOR WHAT YOU RECEIVE IF MERCHANDISE IS DAMAGED CALL CARRIER AND SECURE DAMAGE INSPECTION REPORT YOU HAVE 15 DAYS TO SECURE DAMAGE REPORTS OTHERWISE YOU MAY LOSE YOUR PRIVILEGE OF FILLING A CLAIM FOR LOSS OR DAMAGE LIMITED WARRANTY Contents Important PMI WARRANTS THIS PRODUCT TO BE FREE FROM DEFECTS IN MATERIALS AND Note Caution and Warning Statements WORKMANSHIP 1 Introduction nsin eini uade reete sa 2 Product sodio tb oats PLEASE NOTE THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW Ses ISCAS OM eR 5 APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4 1999 4 es a tain ila 6 do p eee nee 7 THIS WARRANTY IS EXTENDED ONLY TO ORIGINAL PURCHASER USER OF OUR PRODUCTS Ge SOIVIC B corda ete Lost oia cn ened 7 Troubleshooting
6. bed in this manual Use this product only under physician s direction Do not use the equipment with accessories other than those provided by your homecare provider respiratory therapist or physician Never operate this product if a it has a damaged cord or plug b it is not working properly c it has been dropped or damaged d it has been dropped into water Return the product to your homecare provider for repair or replacement Keep the power cord away from heated or hot surfaces Never block the air openings of this product or allow objects to fall or be inserted into the air vent openings or place it on a soft surface such as bed or couch where the air openings may be blocked This device SHALL NOT be used if the room temperature is warmer than 95 Fahrenheit to prevent the temperature of air delivered to the patient over 104 Fahrenheit CAUTION Use the Zzz PAP Integrated Heated Humidifier only with the Zzz PAP CPAP system FDA approved accessories NOTE U S Federal law restricts this device to sale by or on the order of a licensed physician GROUNDING INSTRUCTIONS This product should be grounded In the event of an electrical short circuit grounding reduces the risk of electric shock by providing an escape wire for the electric current This product is equipped with a cord having a grounding wire with a grounding plug The plug must be plugged into an outlet that is properly installed and grounde
7. ber to the fill line NA with distilled water approx 450 ml 3 Press down and slide the chamber into place Make sure the silicon connector on the inlet connector fit securely over the CPAP device air outlet Silicon Connector Note Make sure the water chamber is pushed to the end to press against the heater plate switch At the same time the heater on indicator will be lit to indicate the heater plate starts to warm Note The heater will be automatically turned off while the water chamber is removed from the heater platform Heater Plate Switch 4 Connect the 6 flexible tubing to the outlet connector on the water chamber
8. cable collection point for the recycling of electrical and electronic equipment For more detailed information about the recycling of this product please contact your local city office household waste disposal service or the retail store where you purchased this product 1 Introduction This manual should be used for initial set up of the system and saved for reference purpose 1 1 General Information This system has been tested and successfully approved to the following standards EN60601 1 EN60601 1 2 EMC Warning Statement This equipment has been tested and found to comply with the limits for medical devices to the EN 60601 1 2 2004 These limits are designed to provide reasonable protection against harmful interference in a typical medical installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to other devices in the vicinity However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to other devices which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving device Increase the separation between the equipment Connect the equipment into an outlet on a circuit different from that to
9. d DANGER improper use of the grounding plug can result in a risk of electric shock If repair or replacement of the cord or plug is necessary do not connect the grounding wire to either flat blade terminal The wire with insulation having an outer surface that is green with or without yellow stripes is the grounding wire Check with a qualified electrician if the grounding instructions are not completely understood or if in doubt as to whether the product is properly grounded If it is necessary to use an extension cord use only a 3 wire extension cord that has a three blade grounding plug and a 3 slot receptacle that will accept the plug on the product Replace or repair a damaged cord GROUNDING METHOD For 120V System Only ADAPTER GROUNDED OUTLET e e METAL SCREW gu 11 POUNG Ta OUTL GROUNDING 7 ET BOX GROUNDING SCREW PIN A B C 10 8 Technical Description ic NOTE CAUTION AND WARNING STATEMENTS Item Specification Heater Settings 1 to 6 from 86 F 140 F Pressure Drop 0 2cmH20 60LPM Humidity Output 10 40mgH20 L Operating Environment Temperature 50 F 95 F Humidity 10 90 RH Atmospheric Pressure 609 768mmHg Transport Storage Environment Temperature 4 F 158 F Humidity 10 90 RH Atmospheric Pressure 609 768mmHg Classification Class I Type BF IPXO Not suitable for use in the presence of a flammable a
10. er are subject to normal wear and tear and may eventually be replaced Replace the chamber assembly as necessary 2 Product description Baffler Extraction Tool Heater Plate Heater Plate Switch Water Chamber Fill Line Flow Direction Baffler Extraction Tool Heater Plate Heater Plate Switch Control Knob Power On Indicator Green LED Heater On Indicator Yellow LED Inlet Port with Silicon Connector Outlet port AC Power Cord Power Socket Inlet Power Jumper Cord Power Socket Outlet Power Switch Locking Tab C Heater Platform Fill Line 3i Outlet Port 52 Silicon Connector Flow Direction Water Chamber Removable Base Plate Power Jumper Cord S 778 x Power Switch Power Cord Heater ON Indicator 05 x Power Socket Inlet Control Knob Power ON Indicator The water chamber contains the water for humidification Its removable base plate allows itself ease for cleaning Symbol indicates the maximum level of water that water chamber can contain Symbol Indicates the air flow direction The baffler can prevent water spillage due to improper shaking Open the water chamber for cleaning Warms the water in the water chamber When the switch is pressed against the water chamber the heater plate will start to work This control knob graduated from 1 to 6 is used to adjust the heating temperature of the heater plate from 86 F to 140 F When l
11. er plate over heated 1 Contact your homecare provider for will not light at all 2 indicator worn out assistance 2 Contact your homecare provider for assistance There is no air flow 1 CPAP device is not powered on or 1 Refer to your CPAP user manual through the mask working correctly 2 Reconnect the flexible tubing 2 Flexible tubing is not connected correctly right 3 Unblock the flexible tube 3 Flexible tube is blocked Condensation in 1 The heater plate setting is too 1 Adjust the control knob to lower mask or flexible high temperature setting tube 2 operating environment or 2 Remove any air conditioner which position of heated humidifier is not may nearby the heated humidifier acceptable the room temperature Or keep room temperature above is too low 57 F Water Leakage 1 Assembly of water chamber is not 1 Remove the water chamber from the correct heated humidifier empty out the 2 Water chamber or removable base water and reassemble the water plate is defective or broken chamber again make sure the removable base plate is aligned correctly to fit into water chamber and fill as described in the manual Test for leakage 2 Replace the water chamber assembly 5 Connect the other end of the flexible tubing to your mask 6 Adjust the heater temperature to the desired setting by the control knob The 1 6 setting corresponds to the temperature as follows 1 approximately 86
12. fier base to the off position immediately after use Do not use while bathing Do not place or store product where it can fall or be pulled into a tub or sink Do not place in or drop into water or other liquid Do not reach for a product that has fallen into water Unplug immediately Do not reach into the water or other liquids if product falls into water or other liquids Unplug it immediately WARNING To reduce the risk of burns electrocution fire or injury to persons Do not operate CPAP Continuous Positive Airway Pressure which is used for the treatment of Obstructive Sleep Apnea before mask and humidifier installed Disconnect the humidifier from CPAP unit when not in use water entering the CPAP unit may result in electric shock hazard or damage to the CPAP unit Do not use if water comes in contact with the CPAP unit or enters the tubing Heated Humidifier is not for use with patients whose supraglottic airways have been bypassed Do not operate with blanket clothing or any other fabric material or under the humidifier Do not remove water chamber while humidifier is heating Do not touch the heater plate for 30 minutes after the device is powered off and unplugged This product should never be left unattended when plugged in and powered up Close supervision is necessary when this product is used by on or near children or the elderly Use this product only for its intended use as descri
13. it this indicates the humidifier is powered on and ready for operation When lit this indicates the heater base is warming the chamber Connect to the outlet port of the CPAP device Connect the flexible tubing here Connect to an AC outlet providing main power to the heated humidifier Connect the AC power cord here Connect the heated humidifier and the CPAP device Connect the power jumper cord here Power the Zzz PAP heated humidifier ON or OFF 3 Installation 3 1 Set Up 1 Place the CPAP device on the heater platform Position the CPAP device so that the four feet match up with the four recessed areas in the platform and the rubber tab at the back of the platform slips into the slot in the rear of the CPAP unit beneath the power socket locking the device securely into place 2 Place the CPAP and heated humidifier base on a flat surface and at a lower level than your sleeping position 3 Connect the power jumper cord to the power socket outlet on the back of the heater and the AC inlet on the back of the CPAP device 4 Connect the AC power cord to the power socket inlet on the back of the heated humidifier base and plug it into main outlet NOTE The plug is also serves as a disconnect device 4 Operation 4 1 Operating instruction Daily Use 1 Power on the heater by pressing the On Off switch on the rear of the heated humidifier base The power on indicator will be lit green light 2 Fill the cham
14. nesthetic mixture No AP APG Protection Continuous operation Compliance Standard EN60601 1 NOTE 1 The specification is also suitable for other areas operating with same power supply 2 Consult your homecare provider for other technical documents x 4 PB DANGER Danger indicates an immediately hazardous situation which will result in death or Model No 95 006000 serious injury if not avoided Power Requirement 120VAC 50 60Hz 0 9A For 120V system WARNING Warning indicates a potential hazardous situation which will result in death or serous see rating label on the product 220V 240VAC 50 60Hz 0 5A For 230V system injury if not avoided Fuse Rating T2A 250 VAC CAUTION Caution indicates a potential hazardous situation which will result in property damage Dimensions Heater 10 x 6 8 x 1 6 25 5 x 17 2 x 4 cm or destruction of equipment if not avoided Water Chamber 5 9 x 4 5 x 4 2 14 9 x 11 5 x 10 6 cm NOTE Note indicate some tips that user should pay attention to Weight Heater 0 84 Ib 380g Water Chamber 0 53 Ib 240 g Water Capacity 450ml SYMBOLS BF symbol indicate this product is according to the degree of protecting against electric shock for type BF equipment Attention should read the instructions before use Grounding terminal Fill line Air flow direction Disposal of Electrical amp Electronic Equipment WEEE This product should be handed over to an appli
Download Pdf Manuals
Related Search