STC-TGL2M User`s Manual Toll Free Customer Support 1-888
Contents
1. www wildviewcam com Toll Free 888 304 6125 Open view image with major parts indication STC TGL2M Battery Cover Passive Infrared Sensor PIR Test Indicator LCD Display Screen Burst Mode d Camera Sensor Test Swtich Picture Quality Switch Time Out Switcl www wildviewcam com Toll Free 888 304 6125 Camera Lens Low Battery Indicator SD Card Slot Flash Flash Control Switch Lock Hole STC TGL2M Picture Image Capacity HL BE UE 1200 iog aes eae mm fos ow 3 16MB 26 40 8 32MB 52 80 16 64MB 104 160 32 128MB 208 320 64 256MB 416 640 128 512MB 832 1280 256 NOTE Picture Image Capacity Chart provides approximate number of images or AVI movies based on resolution setting and the size of memory card These figures may vary depending on the amount of detail in the image www wildviewcam com Toll Free 888 304 6125 STC TGL2M Camera kit contents e Model STC TGL2M Digital Scouting Camera e Camera driver e User Manual e 1 5M USB cable e Strap www wildviewcam com Toll Free 888 304 6125 STC TGL2M Battery amp memory installation Warning Do not use different Voltage lead acid battery other than the one specified in this section Doing so will damage the camera and will void the warranty The Wildview STC2. www wildviewcam com Toll Free 888 304 6125 30 STC TGL2M e Avoid dropping the Wildview scouting camera on to hard ground Do not disassemble the Wildview Scouting camera e Do not mix new and old batteries e Do notopen the camera for unauthorized service This could cause serious damage to the unit and will void the warranty This camera is a precision electronic device Do not attempt to service this camera yourself as opening or removing covers may expose you to dangerous voltage points or other risks Caution When camera is switched off if there is any residual power left in the camera it will take an extra picture to discharge the left over power in the camera Under low lighting condition the flash will go off WF043A R2 Print in China www wildviewcam com Toll Free 888 304 6125 31
3. TGL2M Digital Scouting Camera is designed to operate using alkaline batteries for optimum performance NOTE Always have camera in OFF position when installing or removing batteries Batteries C cell The internal battery compartment accepts 4 C cell batteries Be sure to use high quality brand name alkaline batteries Install batteries in correct polarity as noted inside battery compartment www wildviewcam com Toll Free 888 304 6125 STC TGL2M 12V Lead Acid external battery The STC TGL2M is equipped with an external power jack designed to accept a barrel plug cable to attach toa sealed lead acid battery sold separately Battery cable and complete 12V Lead Acid battery kits are available wherever Wildview scouting cameras are sold or call toll free 888 304 6125 Only Wildview external battery accessories are recommended e Insert the battery pack plug into the DC 12V jack at the bottom of camera housing e Turn on the camera by sliding the power switch to PIR position Please make sure the voltage and polarity are correct before connection Incorrect voltage or polarity will damage the camera Memory Options Your Wildview scouting camera is equipped with 16MB built in SDRAM memory The camera is also equipped with an expandable media card slot capable accepting up to 512MB SD card sold separately With no memory www wildviewcam com Toll Free 888 304 6125 9 STC TGL2M card inserted into
4. the slot the camera will use the built in 16MB SDRAM memory If a SD card is inserted into the slot then the camera will bypass the built in memory and utilize the SD memory The front counter display will show the number of images on the built in memory unless the expansion card is inserted at which point the counter will only show the number of images in the expansion card Inserting SD card Make sure camera is in the OFF position whenever adding or removing memory e Insert SD memory card in to the SD card slot completely and in the correct direction as shown on the inside of the housing e To remove the SD memory card depress the SD card and pull out the card gently SD cards must be clean no images from other sources www wildviewcam com Toll Free 888 304 6125 10 STC TGL2M Definition e Time out To set the amount of preset time in minutes the camera will sleep between PIR triggering e Resolution The resolution selection that you have selected o High Select this option to capture a 2 0M pixel image quality o Low Select this option to capture a 1 3M pixel image quality e Date Time To set date and time stamp in the picture e Flash Auto On Off mode www wildviewcam com Toll Free 888 304 6125 11 STC TGL2M Burst To set number of picture the camera will take per PIR triggering o 1P Single image capturing per PIR triggering o 2P Two images continuous capturing per PIR triggering o 3P Three i
5. Ez STC TGL2M User s Manual Toll Free Customer Support 1 888 304 6125 www wildviewcam com Version 1 3 08 06 STC TGL2M For Customer Service or Warranty Information Call Toll Free 888 304 6125 WILDVIEW P O Box 535189 Grand Prairie Texas 75053 5189 www wildviewcam com Wildview Scouting Camera Limited Warranty Your Wildview Scouting Camera is covered by a One Year Limited Warranty on parts amp labor from the date of purchase The warranty covers defects in workmanship amp materials The warranty does not apply to units which have been damaged or abused intentionally or unintentionally Tampering with or altering the unit will void the warranty Any unauthorized service will void warranty Original sales receipt must be produced for any warranty service Questions call 888 304 6125 www wildviewcam com Toll Free 888 304 6125 STC TGL2M Manual Contents Camera overview Camera kit contents Battery and memory Installation Definition Programming Mounting the camera Viewing images Saving and Deleting images Memory compatibility chart Technical Specs General Information 11 13 16 20 23 26 27 30 www wildviewcam com Toll Free 888 304 6125 STC TGL2M Camera overview Front view Side view CX LII Ld 0 J J
6. OT attempt to replace the batteries before you save the images in your PC Once the battery is drained completely or if you attempt to replace the battery all images in the internal SDRAM memory will be lost www wildviewcam com Toll Free 888 304 6125 25 STC TGL2M SD Compatibility Chart The following cards have been tested and approved for use in the Wildview STC TGL2M model PQI 32MB 64MB 128MB 256MB 512MB San Disk 32MB 64MB 128MB Panasonic 32MB 64MB 128MB Toshiba 32MB 64MB 128MB 256MB 512MB King Mate 32MB 64MB 128MB 256MB 512MB Lexar 512MB Kingston 128MB 256MB 512MB Kodak 128MB 256MB 512MB Dan Elec 128MB 256MB 512MB Viking 128MB PNY 128MB 256MB 512MB Proper camera operation cannot be guarantee when using memory card NOT listed above www wildviewcam com Toll Free 888 304 6125 STC TGL2M Technical Specifications System Requirements and Compatibility e Windows 98 98se 2000 Me XP e Pentium Ill 450MHz or equivalent processor e 128MB SDRAM or above e VGAV Video Card with 32MB RAM for minimum Color 16 bit or higher e An available CDROM driver and an available USB Port e 600 MB free hard disc space If you have any questions regarding your PC specifications please call your PC manufacturer www wildviewcam com Toll Free 888 304 6125 27 STC TGL2M Camera Features and Specification Image sensor 1 3 mega pixels 2 0 mega pix
7. d in the memory o Delete One picture a Press SET button to enter delete setting Display will show ESC b Press UP or DN to select d ONE delete one c Press SET to delete the image Press UP www wildviewcam com Toll Free 888 304 6125 23 STC TGL2M or DN until screen shows ESC then press SET again to exit d This will only delete the last image saved in the memory o Delete All picture a Press SET button to enter delete setting Display will show ESC b Press UP or DN to select d ALL delete all c Press SET to delete all images and display will show DONE and exit to count down mode automatically o Format a Press SET button to enter delete setting Display will show ESC b Press UP or DN to select Ft format c Press SET to confirm and display will show DONE and exit to count down mode automatically www wildviewcam com Toll Free 888 304 6125 24 STC TGL2M o ESC To exit delete setting 2 Simply remove the battery from the battery compartment This will delete the image stored in the internal SDRAM memory CAUTION Do not remove the battery until you have down loaded all the images in the internal SDRAM Once the battery is removed all images in the internal SDRAM will be deleted This does not apply to images stored in SD card RED LED indicator will blink when battery is low Turn off the camera Down load the pictures immediately DO N
8. els interpolation Built in 16MB SDRAM memories for image storage External memory support SD memory card up to 512MB Resolution Options 2 0M 1 3M QVGA Video Auto white balance and auto expose Auto On Off Flash light strobe control 4 digits LCD Image counter Battery low indicator Green Test LED indicator Focusing 5 ft to Infinity 4 P glass lens with IR coating Effective viewing Angle 52 deg www wildviewcam com Toll Free 888 304 6125 28 STC TGL2M PIR detection angle 48 deg Low power consumption Standby current 4mA Capture current 120mA Interface type USB 1 0 Power C size alkaline Batteries x 4 Image format Standard JPEG And Motion JPEG AVI www wildviewcam com Toll Free 888 304 6125 29 STC TGL2M General Information Storing conditions Operating Environment 14 to 104 deg F 10 to 40 deg C 20 85 relative humidity non condensation Special care instructions The camera is designed to be weather resistant Never attempt to immerse the unit to water or any other liquid This will damage the unit and void the warranty Use a soft lens cloth for cleaning lens Avoid touching lens with fingers Remove dirt or stains with a soft cloth dampened with water or neutral detergent Keep the Wildview scouting camera in a dry and cool dust free environment or container when it is NOT used Take the batteries out when the Wildview scouting camera is NOT to be used over a long period
9. f the camera e Connect your camera to the PC by the USB cable the PC will recognize the new device and set up the configuration of the PC automatically Front LCD on your camera will show the word USb NOTE Users of Windows 98 must install camera driver prior to connecting the USB cable www wildviewcam com Toll Free 888 304 6125 21 STC TGL2M e If your computer doesn t run automatically please click Start button and choose Run and then browse the CD drive and click Setup Viewing the images on your computer e Slide the power switch to OFF location e To view the images simply plug one end of the USB cable into an available USB port on your computer e Plug the other end of USB cable into the camera The camera will automatically power ON Front LCD screen will show USb e Atthe same time your computer will recognize the camera as mass storage device and found under MY COMPUTER www wildviewcam com Toll Free 888 304 6125 22 STC TGL2M Saving and Deleting images SAVING IMAGES To save images on to your PC simply copy and paste or drag and drop from the SDRAM memory to your PC desk top DELETING IMAGES There are two ways to delete the images from the internal SDRAM memory 1 After you down load image into your desk top you can delete the image in the SDRAM Unplug the USB Cable from camera Slide the power switch to PIR position LCD screen will display the number of images capture
10. ink Press UP or DN to adjust month f Press SET button to enter date setting Date amp DD will blink Press UP or DN to adjust date g Press SET button to enter year setting Date amp YY will blink Press UP or DN to adjust year www wildviewcam com Toll Free 888 304 6125 14 STC TGL2M h Press and hold SET button for 2 seconds to exit the setting mode and into PIR count down mode Display will show date and number of picture taken Once the program setting has been completed slide the power switch to OFF position until you are ready for field use NOTE Date amp Time setting will be lost whenever battery is removed from camera Don t forget to re set the Date amp Time stamp after you replace the battery www wildviewcam com Toll Free 888 304 6125 15 STC TGL2M Mounting the camera It is recommended to mount the camera 4 5 ft off the ground with the camera pointed at a slight downward angle Be sure to avoid mounting the camera facing east or west as the rising and setting of the sun could produce false triggers and overexposed images Clear branches and other debris away from the front of the camera so as not to block the camera lens or PIR sensor 40 20 CAMERA 4 5ft 30 FT sis EFFECTIVE DISTANCE 30 FEET HORIZONTAL PIR Coverage Area Diagram www wildviewcam com Toll Free 888 304 6125 16 STC TGL2M Mounting the camera with the supplied st
11. mages continuous capturing per PIR triggering o AVI 10 seconds video clip per PIR triggering FULL When memory capacity is full this front LCD screen will show FULL www wildviewcam com Toll Free 888 304 6125 12 STC TGL2M Programming The following setting must be performed before you turn on the camera 1 Select the time out interval by sliding the time out toggle switch to the desire preset time interval in minutes 1 5 10 20 minutes Select the resolution setting by sliding the resolution toggle switch to the desire resolution setting Hi Lo resolution Select the Flash mode Slide the switch to either Auto On Off position a Auto Flash on based on surround lighting condition b On Flash on for every image captured c Off No Flash will go off Select Frame mode Slide the switch to 1 2 3 AVI position If you choose AVI mode the camera will automatically switch to 1 picture mode if it detect low light source www wildviewcam com Toll Free 888 304 6125 13 STC TGL2M 5 Turn on the Camera to set the Date Time stamp a Slide the power switch to PIR position b Press and hold SET button for 2 seconds to enter date amp time setting mode c Time and HH will blink Press UP or DN to adjust hour d Press SET button to enter minute setting Time and MM will blink Press UP or DN to adjust minute e Press SET button to enter month setting Date amp MM will bl
12. rap Camera TREE TRUNK Buckle e Insert the strap through the strap slots on the rear housing e Wrap the strap around the mounting surface Secure the strap and tighten the buckle in order to secure the camera www wildviewcam com Toll Free 888 304 6125 17 STC TGL2M In order to obtain proper weather resistance please make sure that both door latches are securely locked in place Testing the camera coverage area One of Wildview Scouting Camera s features is the ability to test the coverage area e After mounting the camera open front housing and slide the power switch to Test position The front LCD will display the word tESt e Close the front housing e Walk around in the front of the camera to see if you have mounted camera in the proper position A green indicator light on the front will blink on when you have intruded the coverage area e Adjust the camera position as needed and repeat testing until the desired coverage area is achieved www wildviewcam com Toll Free 888 304 6125 18 STC TGL2M e When you have completed the testing the coverage area open the front housing and slide the power switch from Test position to PIR position Front LCD counter will show 0000 The camera will enter count down mode for 1 minute and front green indicator will start blinking giving you one minute to leave the coverage area Then camera will enter PIR detection mode NOTE Make sure you slide the po
13. wer switch from TEST mode to PIR mode before you leave the field Otherwise the Camera will not take any pictures Switch use Do not move the switch from TEST directly to PIR Doing so will cause the camera to not operate Slide the switch to OFF Wait for the front LCD screen to turn off then continue to slide the switch to PIR www wildviewcam com Toll Free 888 304 6125 19 STC TGL2M Viewing images Viewing images by computer download The Wildview Scouting Camera is a plug and play USB storage device This means users of Windows 2000 ME and XP operating system need not install the camera driver This camera is not MAC compatible The CD ROM included in this package contains the camera driver for older operating system only Attention The software CD ROM packaged with the camera is designed for PC s only not MAC compatible Playing this CD ROM on a stereo or CD player may cause damage to it Driver installation e Unplug the USB cable from PC e Insert the CDROM in CD driver of your PC e The auto run program will execute www wildviewcam com Toll Free 888 304 6125 20 STC TGL2M e Follow the instructions shown on screen from your PC to completely install the driver and application program e Ifthe existing DirectX version on your PC is lower than version 8 and if you have problem viewing the image with the standard software provided by Microsoft then you should install DirectX 8 e Restart windows e Turn of
Download Pdf Manuals
Related Search