Chapter 1
Contents
1. See p 1 23 10 Testthe printer onina ana naea a aa aa a aE a AET A aiaei See p 1 24 11 Testthe interface with the COMputer cccecsscccsssecsscecssteessseessrsecenreessseeessseesenreseats See p 1 25 12 Install the printer driver ccceccsccccssecsscecssscecsesceceeceeesesseescsesescseesenresssaseecsueeserseseaes See p 1 26 1 11 Setup and Connections 1 Install the printer on the paper feeder Option Align the installation holes on the bottom of the printer with the positioning pins on top of the paper feeder and slowly lower the printer into place Check that the connector on top of the paper feeder is properly connected to the connector on the bottom of the printer Connector Optional Paper Feeder PF 16 Positioning Pins 1 12 2 Remove the process unit protective cover 1 Open the printer top cover all the way Top Cover Process Unit Protective Cover Process Unit Chapter 1 Installing the Page Printer 2 Liftthe process unit out of the printer The drum in the process unit is sensitive to light Do not expose the drum even to normal office lighting 500lux for more than five minutes Process Unit 1 13 Setup and Connections 3 Pull and remove the process unit protective cover and give the process unit a horizontal shake of 4 to 5 times Process Unit Protective Cover Process Unit 4 Install the process unit in the printer In doing so carefully align the2. After SIMM has been installed in the printer use the following procedure to check that installation has been performed properly 1 38 Chapter 1 Installing the Page Printer Testing Extended Memory 1 Check that the power switch is off plug the power cord into the printer and turn the power on 2 Wait for the printer s ON LINE indicator to light and the message display to read Fa ciiy then press ENTER STATUS key briefly 3 If installation has been performed properly a status page will be printed Check the Memory in the upper right Information on the SIMM installed in slot is shown here There is no problem if total memory has increased The printer is shipped from the factory with 4096 KB 4 MB of memory 1 39
3. Insert the SIMM into the socket on the printer s main board Take precautions that no foreign substances such as metal chips or liquid get inside the printer during the installation process Operation of the printer during the presence of a foreign substance may lead to fire or electric shock Be sure to turn off the printer s power and disconnect all cables when installing SIMM in the printer Failure to do so may lead to electric shock Chapter 1 Installing the Page Printer Draw the main circuit board all way out of the printer as follows 1 Turn the printer s power off Unplug the printer s power cable and disconnect it from the host computer Screws 1 35 Expanding Memory 1 36 3 Pull the main circuit board all the way out of the printer Before pulling the main board out clean the area on the table etc at the back of the printer s rear panel Foreign objects if accidentally stuck to the back of the main board may cause serious damage to the printer Socket Chapter 1 Installing the Page Printer 4 Insert the connector end of the SIMM into the socket Carefully push the board upright until it snaps into place Make sure that the catches at the ends of the socket fit into the holes at the ends of the SIMM board 1 37 Expanding Memory 5 To remove the SIMM carefully pull the end catches sideways slightly and tilt the SIMM to the left as shown then pull the SIMM out of the socket
4. broken Notes on Application Software The computer and printer have been successfully connected by the procedures up to this point In order to print from software run on the computer it is necessary to install a printer driver on the computer to which the printer is connected After the printer driver is installed be sure to make proper printer settings from within the software 1 25 Setup and Connections 12 Install the printer driver A CD ROM containing a printer driver for Windows Windows 3 1 Windows 95 and Windows NT 3 51 4 0 is supplied with this printer Once this printer driver is installed on the computer it is possible to make various settings for this printer from within Windows applications It is also possible to control options and printing from within Windows For each of these operating systems the printer driver is located in the folder on the CD ROM The steps for installing this driver are given below Read this in conjunction with the manual supplied with Windows For details on how to install the printer driver under Windows NT read the file README TXT in the CD ROM s root directory Installing Under Windows 95 1 Insert the supplied CD ROM into the CD ROM drive of the computer 2 Click on Start with the mouse on the Windows 95 Task Bar and align the cursor with Settings Click on Printers among the items displayed Ey Brogens i Doumer a Loit Pana jk BEEE
5. guides at the both ends of the process unit properly with the slots in the printer 1 14 Chapter 1 Installing the Page Printer 3 Install the toner container 1 Take the toner container from the bag Shake the toner container with the protective seal orange colored facing up as shown in the figure five times or more to thoroughly mix the toner inside Shake five or more times Protective Seal Orange colored 2 Carefully remove the protective seal as shown in the diagram Toner Container 1 15 Grooves Setup and Connections 4 Check that the toner container is installed in the correct position and push forcefully on the top of the toner container at PUSH HERE 4 Close the top cover Close the top cover 1 16 Add paper Chapter 1 Installing the Page Printer Try as much as possible to use fresh paper which has just been opened Paper which has been stored long periods contains moisture and may result in sheets sticking together and or paper jams For specifications on the paper which can be used with this printer refer to Appendix B Paper Selection 1 Pull the paper cassette all the way out of the printer 2 Cassette Cover 1 17 Setup and Connections 3 Adjust the position of the paper stopper located at the rear of the cassette While holding up the paper stopper slide the paper stopper to the desired paper size 4 Adjust the position of the paper guides
6. located on the left and right side of the cassette Align the paper guides to the desired paper size by lifting the paper guides so they slide Move the side guides inward to where they just touch the edges of the paper Do not load more paper than will fit under the load limits on the top of the paper guides The cassette will hold approximately 150 sheets of paper with a 80 g m 21 Ib basis weight or with a thickness of 108 microns Load Limit 1 18 Chapter 1 Installing the Page Printer 5 Close the cassette cover Cassette Cover 6 1 19 Setup and Connections 6 Open the paper stopper on the face down tray Raise the paper stopper on the face down tray as shown in the figure 7 Open the face up output tray when the tray is being used Use the face up output tray when you wish paper to be stacked with the printed side facing up reverse order The face up output tray is located on the back side of the printer Use it by opening as shown in the figure Face up output tray 1 20 Chapter 1 Installing the Page Printer 8 Connect the printer to the computer Before performing this step be sure to turn off the printer s power switch and unplug the power plug from the power outlet Failure to do so may result in electric shock A standard Centronics parallel interface connector Ey is located on the rear side of the printer For pin connections please refer to Appendix C Option Interf
7. Chapter 1 Installing the Page Printer Chapter 1 Installing the Page Printer This chapter uses illustrations to explain the names of parts of this printer how to use it its environmental requirements and how to install it Environmental Requirements of the Page Printer 1 2 Unpacking and INSpection eeen 1 6 MOVING the Printer cccccceccscecssecccsecsersecsteessseesstseeeseeeseas 1 8 Names of Parts onia auat aariaa aN nits 1 9 Setup and COnnectoOnS eree 1 11 Expanding MemMOry sssssssriersrieeirrreiierirrierierineierine nerenin 1 32 Environmental Requirements of the Page Printer Environmental Requirements of the Page Printer Places to Avoid Avoid installing the printer in locations subject to Direct drafts of hot or cold air Direct drafts from outside Avoid locations near doors leading outside Sudden temperature or humidity changes Sources of high temperature for example near stoves or radiators Excessive dust Vibration Ammonia or other harmful fumes If you are planning to fumigate the room or make liberal use of insecticide remove the printer first Excessive sunlight or humidity Lack of ventilation Low air pressure e g located more than 2000 meters 6500 feet above sea level Basic requirements The printer will work best if it is installed in a location that is Near the computer If the parallel interface is used to connect the printer to the computer the conne
8. Start Button 1 26 Chapter 1 Installing the Page Printer 3 The printer folder will open Double click on Add printer Printers e x File Edit View Help 4 The Printer Wizard screen will appear Click on Next gt 5 A screen for selecting the printer to be either a local printer or network printer will appear Select the appropriate connection and click on Next 6 Next Click the manufacturer and model of your printer screen will appear At this point select Have Disk located at the lower right See the figure for Step 7 7 Enter CD ROM Drive Name as the source from which to copy the file and click on OK 1 27 Setup and Connections Add Printer Wizard Install From Disk as CD ROM Drive Namely z _ Browse 8 Select Kyocera FS 800 click on Next gt and follow the on screen instructions to install Once the driver has been properly installed a Kyocera printer icon will be added to the Printers folder Note When printing under Windows 95 be sure to set the emulation of this printer to HP Laser et 5Si default setting 1 28 Chapter 1 Installing the Page Printer Installing Under Windows 3 1 1 Insert the supplied CD ROM into the CD ROM drive of the computer 2 Double click on the Control Panel Program Manager Main Hg Clipboard Print Manager Viewer 3 Double click on Printers Control P
9. ace Slot Cover Parallel Interface Connector 1 21 Setup and Connections Parallel Interface Connection 1 22 Plug one end of the printer cable into the connector on the printer marked with a E parallel symbol Close the clips on both sides to fix the connector in place Printer Cable Rear panel Plug the other end of the printer cable into the computer s parallel Centronics interface connector This connector is usually labled PRINTER For details refer to the hardware manual for the computer Chapter 1 Installing the Page Printer 9 Attach the power cord Be sure the printer s power switch is turned off Note Only use the power cord supplied with the printer 1 Plug the power cord into the power cord connector on the rear side of the printer Power Cord Connector Power Cord 2 Connect the other end of the power cord into a power outlet Be sure to connect the ground wire of the printer to ground 1 23 Setup and Connections 10 Test the printer 1 24 Use the following procedure to test the printer and print out a status page indicating factory settings For details on the indicators and keys on the printer s control panel please refer to Chapter 2 The Control Panel 1 Turn on the printer s power switch It does not matter whether the computer s power is on or off st will be displayed in the message display of the printer Note An error message Fop over Cin w
10. anding memory Printer memory can be expanded to up to 36 MB by installing optional extended memory chip SIMM in the slot Note The expansion memory should be installed only by a Kyocera authorized dealer or Kyocera certified technician Kyocera shall not be liable for damage due to improper installation of the expansion memory Memory Required by the Printer Environment It may be necessary to extend memory depending on the operating environment of the printer Please refer to the table below for minimum memory requirements in various environments Environment 300 dpi 600 dpi HP Laser et 5Si KP DL resource protection Po 10 MB 1 32 Chapter 1 Installing the Page Printer The description given below is intended for service personnel Precautions on the Handling of Extended SIMM Static electricity which may accumulate in the human body through walking on carpets or other such surfaces is the enemy of SIMM loaded with many semiconductor chips Pay attention to the following things before installation to protect memory chips against damage from static electricity Do not remove the SIMM from their anti static bag until immediately prior to installation Eliminate any static electricity from your body through grounding before touching the SIMM Be absolutely sure when handling the SIMM to hold them by the substrate without touching the printed connector section 1 33 Expanding Memory Installing SIMM 1 34
11. anel Settings Help e gt va GP P Color Ports Mouse Desktop S Keyboard International Date Time 386 Enhanced Drivers 1 29 Setup and Connections 4 Click on Add gt gt 5 A screen for List of Printers will appear From the choices click on Install Unlisted or Updated Printer inter Default Printer Installed Printers gt Use Print Manager 5 List of Printers Install Unlisted or Updated Printer 1 30 6 Chapter 1 Installing the Page Printer Click on Install 7 The Install Driver menu will appear Enter CD ROM Drive Name and click on OK Install Driver Insert unlisted updated or vendor provided printer driver disk in CD ROM Drive Name 4 Set As Default Printer gt Use Print Manager List of Printers Install Unlisted or Updated Printer Refer to the Readme txt file at the root directory of the CD ROM and browse to the directory which contains the appropriate drivers for your country Select Kyocera FS 800 from the printers displayed and click on OK Once the driver has been installed close the Control Panel by clicking on Close 1 31 Expanding Memory Expanding Memory The printer comes standard equipped with 4 MB of main memory However more complex pages can be printed and processing speed increased by expanding the printer s memory There is one slot available in the printer for exp
12. ce surrounding the printer Continued use without enough space may cause heat to build up within the printer resulting in fire 30 cm 11 8 inches 40 cm 15 7 inches 5 cm 2 inches 25 cm 9 8 inches 50 cm 19 6 inches 1 5 Environmental Requirements of the Page Printer Basic handling precautions Removing or changing parts other than disposable parts is prohibited For repairs contact the Kyocera dealer from which you purchased the printer When moving the printer to a new location contact the Kyocera dealer from which you purchased the printer Using this printer to print currency or negotiable bonds is in violation of the law Unpacking and Inspection 1 6 Remove the printer from the package according to the steps given below After removing the printer check that nothing is missing against the list of packaged contents 1 Place the box containing the printer on a flat stable surface 2 Remove the User s Manual Toner Container and other items located on top of the spacer and remove the spacer 3 Carefully remove the printer Chapter 1 Installing the Page Printer List of packaged contents Contents of Printer Box Printer FS 800 Power Cord Toner Container TK 16H User s Manual Cleaning Cloth Kyocera Digital Library CD ROM 1 7 Moving the Printer Moving the Printer Note the following items when moving the printer Be sure to lift the printer gently keeping it
13. cting cable should be shielded type and not be longer than 3 meters 10 feet Chapter 1 Installing the Page Printer Level and well supported Place the printer on a sturdy table or desk Do not place the printer on an unstable cart stand or table The printer may fall causing injury or serious damage to the printer Near an AC wall outlet preferably one that can be used for the printer alone see section Power Supply on next page Only use this printer under the voltage listed on the serial number label attached to the rear panel of the printer Power requirements are Voltage 120 V U S A 220 240 V European countries Australia Asia 10 at each voltage Frequency 60 Hz 120 V 2 50 Hz 220 240 V 2 Max 5 6 A at 120 V or Max 2 8 A at 230 V The outlet should be earthed or an adapter should be used If an extension cord is used the total length of the power cord plus extension should be 5 meters 17 feet or less e Well ventilated not too hot or cold and too damp or dry 10 C to 32 5 C ideally about 23 C 50 F to 90 5 F ideally about 73 4 F 20 to 80 ideally 60 If you install the printer where the temperature or humidity is outside the above ranges you may not get the best print quality and there will be an increased chance of paper jams 1 3 Environmental Requirements of the Page Printer Power Supply 1 4 The printer should not be on the same power circuit as an a
14. horizontal to prevent toner from soiling the inside of the printer 1 8 Names of Parts Chapter 1 Installing the Page Printer Face Down Output Tray Face Up Output Tray Control Panel Paper Cassette Sub Tray Manual Feed Tray Us Power Cord OK Connector Parallel Interface Connector Power Switch Slot Cover for Installation of Optional Interface 1 9 Names of Parts Interior View Top Cover Process Unit Toner Container Release Lever Green 1 10 Chapter 1 Installing the Page Printer Setup and Connections Set up the printer according to the following steps 1 Install the printer on the paper feeder Option cece eee eeeeteeeteeeeeeeeteeeeeetees See p 1 12 2 Remove the process unit protective COVEL ce ccc terete titties tietieesteeteeteeeas See p 1 13 3 2 Llnstalk the Tone ricOntaine ln sinen ann a ajndece tate eaviabean tahece apari See p 1 15 A CloSe the tOp COVEN vseceeisiasheevg deeds aiaa aa a a a a aa aai See p 1 16 5 Add pa O a i a a a a a a aaa a Ta aA a aar a ARNA See p 1 17 6 Open the paper stopper on the face dOWN tray ssssssssessriseiseiesiiersriierierienisrieeinerens See p 1 20 7 Open the face up output tray when the tray is being used nescsccsrecscecrirer See p 1 20 8 Connect the printer to the COMpUtET 0 0 eect ee eee tee tee Entiat EAEE EEEE EE Ennn nenene See p 1 21 9 Attach the power Cordi msiingie a A a aaae a i aeaiia
15. ill be displayed in the printer s message display unless the top cover on the printer is properly closed or the process unit is correctly installed If this happens check that the top cover is properly closed and the process unit is correctly installed 2 Wait until the ON LINE indicator lights and Fs i4 appears in the message display If the ON LINE indicator is off make it light by pressing the ON LINE key 3 Press the ENTER STATUS key Information such as the memory allocation etc currently set for the printer will be printed on a page in a list If the status page prints without problems you can tell that the developer unit and paper feed cassette are installed properly For details on the contents of the status page see Chapter 2 Chapter 1 Installing the Page Printer 11 Test the interface with the computer In order to check that the printer and the computer are properly connected you must print by sending an actual command from the computer 1 Turnon the printer s power switch and turn on the computer s power as well 2 Wait until the ON LINE indicator lights 3 Enter and execute the following command at the DOS prompt on the computer screen ECHO R STAT EXIT gt PRN If this causes the printer to print a status page then the printer and computer are properly connected If this does not print a status page check that the printer cable is properly connected The cable or one of the connectors may also be
16. ir conditioner fluorescent light copier or shredder because these devices generate electrical noise on the power line If it must share a power circuit with equipment like this a high frequency noise filter or isolation transformer is advisable Filters and transformers are available commercially Avoid using plug multipliers to connect a large number of devices on the same circuit as the printer If the power from the outlet itself appears to be unstable a line stabilizer should be used In places where the voltage tends to fluctuate it may be necessary to install a voltage regulator As the disconnect device is not incorporated in the printer s AC primary circuit an easily accessible socket outlet must be provided near the equipment Da kein Trennschalter in den Wechselstrom Primarkreis des Druckers eingebaut ist muB eine leicht zugangliche Steckdose in der Nahe des Gerates vorhanden sein Grounding Surrounding space Chapter 1 Installing the Page Printer Be sure to connect the ground wire for the printer s power supply to the ground terminal of the power outlet to a copper pole buried at least 65 cm 25 inches in the ground or to a water pipe approved by the water department for use as a ground Never use a gas pipe as a ground as this may result in fire Space surrounding the location where the printer is installed is required as shown below for purposes of ventilation and maintenance Be sure to secure enough spa
Download Pdf Manuals
Related Search