HFB 300
Contents
1. HFB300manual GB 15 05 2008 15 54 Pagina 1 a SL ENGLISH 5 IMPORTANT MESSAGES AND FREQUENTLY ASKED QUESTIONS Except handsets what kind of devices can the handsfree communicate with Besides pairing with a handset for receiving and making phone calls the handsfree can also communicate with PDA and computer that equipped with Bluetooth For example when communicating with a computer through a USB Dongle users can chat and or listen music over the Internet 2 Red LED blinking Low battery indicator please recharge your battery as soon as possible 3 Can t power up the device after charging more than 20 minutes For the first time the device should be charged at least 40 minute prior tuning on It is recom mended that the battery should be fully charged before using the device 4 Without charging indicator When the battery runs off or the handsfree has not been used for a while the Red LED may take a while to light up after the charger connected 5 Can t hear anything on handsfree you should check the followings Handsfree is power on Handsfree has paired with a handset Handsfree should connected with a handset except the handset only supports Handsfree Profile e Handsfree and handset are within 10m Handsfree and handset should have good single strength 6 How many devices can a handsfree pair with Handsfree can pair with up to 8 devices please refer section 2 4 2 for details 7 Han2. uses and can Do not allow children to play with your Bluetooth Handsfree Speaker since it contains small radiate radio frequency energy and if not installed and used in accordance with the instructions parts that could become detached and create a choking hazard may cause harmful interference to radio communications However there is no guarantee that This device contains a Li polymer battery Please keep it away from fire anytime including interference will not occur in a particular installation If this equipment does cause harmful interfe discarding the device or the battery may explode rence to radio or television reception which can be determined by turning the equipment off and lt e The Handsfree Speaker especially the embedded battery must be properly disposed or may be on the user is encouraged to try to correct the interference by one or more of the following recycled contacts your local recycling centers for disposal methods measures e Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help CAUTION Any changes or modifications not expressly approved by the grantee of this device could void the user s authority to operate the equipment RF exposure warning The equipment complies with FCC
3. charger has been inserted the device is in normal operation 3 During a call the existing connection between the device and the mobile phone will be reset after inserting the charger The call will be transferred back to the mobile phone momentary The device will try to re establish the connection automatically Sometimes the user needs to short push K2 to reconnect the device 2 1 2 Battery Information Once fully charged the battery for HFB 300 supports continuous talk time up to 5 5 hours and standby time about 500 hours 2 When the battery is low the device beeps once every 20 seconds and the Blue and Red LEDs alternate every 3 seconds charge the battery as described above Note that over charging will reduce battery life If a fully charged battery is left unused it will lose power over time Extreme temperature either too hot or too cold will also affect its ability to charge capacity and lifetime HFB300manual GB 15 05 2008 15 54 Pagina 9 ENGLISH Iu 2 2 Mounting your Handsfree It is easily to mount on the dashboard of the car with mounting dock and double side sticker or use Sun visor Clip to fix the Handsfree device on the sun visor over driver s seat It can be more flexible to use the Handsfree in the car or carry out to the office and home Fixing the mounting dock Plug the part to the inlet then tear the paper off the Double side Sticker paste the mounting dock on the right place
4. on the vehicle Put the device in the mounting dock Note that the char ging port that is on the device and the gap that is on the mounting dock must be at the same direction p a Charging port Mounting dock Inlet Double side sticker Fixing the vent mount clip If using the Vent Mount Clip insert the clip in the vent in the car Note that the microphone of the Handsfree can t aim at the vent to avoid noise in talking mode za XN A bom Mount Clip Fixing the sun visor Fix the mounting dock and the Sun visor Clip and then clip to the sun visor in your vehicle Note that the microphone of the Handsfree must aim at the sound bearing Y 2 3 Turn On Off Handsfree Turn on the Handsfree Long press Kl you will hear 2 power up tones Blue LED gives 3 quick blinks then Blue LED gives blink per 3 seconds Red LED is off This indicates the handsfree is power on Turn off the Handsfree Long press KI you will hear 2 power down tones Red LED will blink 3 times then all LEDs are off This indicates the handsfree is power off 2 4 Pairing Connecting your Handsfree with Bluetooth Equipment 2 4 1 Pairing your Handsfree with Bluetooth handset Before making and answering calls you must pair your handsfree and phone Paring sets up a uni que relationship between your handsfree and your handset The handset will memorize the hands free s unique ID or passkey This ensure
5. remain in the pairing mode for about 2 minutes If paring cannot be finished within 2 minutes the handsfree will enter into the standby mode without Bluetooth connection in this case You need to repeat the above steps 2 5 to restart the pairing process 2 4 2 Pairing your Handsfree with Other Bluetooth Equipment In addition to Bluetooth phone your handsfree can also pair with other Bluetooth equipment for realizing short distance wireless communications HFB300manual GB 15 05 2008 15 54 Pagina 11 ENGLISH ae Similar pairing procedures described in the previous Section can be used You can follow the user guide of the Bluetooth equipment to complete paring operations on the equipment side This handsfree can paired with up to 8 Bluetooth equipments including mobile handsets The corres ponding 8 sets of pairing information are recorded by the handsfree Each paired equipment can wireless communicated with the handsfree after setting up a Bluetooth connection Please check Section 2 4 4 on procedures to set up a Bluetooth connection 2 4 3 Erase all Paired Records This handsfree can paired with up to 8 Bluetooth equipments When Handsfree in the Paring Mode long press K4 it will erase all paired profiles and quit pairing mode At this time Blue LED gives blink per 3 seconds 2 4 4 Connecting Disconnecting your Handsfree with Bluetooth Equipment When the handsfree communicates with a Bluetooth equipment with H
6. 2 Dialing Mute Talk Talk Press K4 and K3 Key Tone LED Pattern 2 together Unmute Talk Mute Press K4 and K3 Key Tone LED Pattern 2 together HFB300manual GB 15 05 2008 15 54 Pagina 17 C Iu ENGLISH Table 4 Transfer Functions 4 MAINTENANCE HFB 300 is well designed communications devices careful maintenance and proper use will extend FUNCTION CURRENT STATUS OPERATION HANDSFREE INDICATOR f S VEN p P the product life and keep their elite performance in delivering voice Following maintenance roce dures may be helpful to you HANDSET AUDIO TONE LED INDICATOR necu T HANDSET HF AUDIOTONE Always turn off power and keep your device in a safe place when it is not in use Ea Talk Talk Long press K2 Key tone LED Pattern e Keep the device dry away from water precipitation humidity moisture and various liquids that handset may corrode electronic circuits If your device gets wet turn it off immediately and wait until Call transfer Talk Talk Long press K2 Key tone LED Pattern 2 the device gets dry completely before using it handset t s ande Keep the device away from dusty and dirty places Otherwise the mechanic and electronic parts could be damaged en dow Power indiration Do not store the device in high temperatures above 30 C or in direct sunlight FUNCTION CURRENT STATUS OPERATION HANDSFREE INDICATOR Extreme high temperature could degrade performance reduce battery lifetime a
7. Blue LED gives 3 quick blinks per 2 seconds and the Red LED is off 2 5 2 Adjusting Handsfree Volume In the talking mode you can short press K3 K4 to increase decrease your speaker volume and the Blue LED gives 3 quick blinks per 2 seconds You can repeat the above operation to speaker volu me to a desirable level Note For most Bluetooth headset handsfree volume control will synchronize with the handset That is your handsfree volume can also be controlled your handset vice versa However this may not be always true due to variations on handset implementations chosen by different manufactures 2 5 3 Mute You can mute or un mute an ongoing call by simultaneously quick pressing K3 and K4 The Blue LED gives 3 quick blinks per 2 seconds and the Red LED is off 2 5 4 Transferring Calls to from your Handset Transferring calls to your handset long press K2 Blue LED gives blink per 3 seconds Red LED is off Transferring calls from your handset short press K2 and Blue LED gives 3 quick blinks per 2 seconds 2 5 5 Voice Dialing If your mobile phone supports voice dialing you can make a call via voice dialing from your Handsfree Voice Dialing Long press K4 you will hear key tone and Blue LED gives 3 quick blinks per 2 seconds then follow your handset user guide to complete voice dialing Cancel Voice Dialing Short press K4 The Blue LED gives 3 quick blinks per 2 seconds and the Red LED is off 2 5 6 Advanced Call Function
8. ESO Se amp Bluetooth AV Service is disconne PAN IP 192 168 50 1 BTHF102 00 13 04 83 00 2E 4 Enter passkey 0000 and confirm to pair the Handsfree with your computer 5 After paired a red V will be there before BTHF202 IVT and Handsfree will connect Bluetooth AV Service automatically 3 IVI Corporation BlueSoleil Nain Window File View My Bluetooth My Services Tools Help OSE ESBS BOVSBeENn Bluetooth AV Service EMEN O DL aai PES p 3 2 o 00 PAN IP 192 168 50 1 Device search completed 6 After connected Start Windows Media Player and configure the speaker interface to be Bluetooth AV HS Audio 7 Restart Windows Media Player and you can listen to the music with Handsfree 8 If you want to chat via Online Messenger or VoIP software you must disconnect Bluetooth AV Service and connect Bluetooth Headset Service Right click BTHF202 and choose Disconnect gt Bluetooth AV Service 9 After disconnected right click BTHF202 and choose Connect gt Bluetooth Headset Service IVI Corporation BlueSoleil Nain Window File View My Bluetooth My Services Tools Help OS Ee Bae BSsoewe amp Bluetooth Headset Service o D o P Bluetooth Headset Service Bluetooth AV Service is disconne PAN IP 192 168 50 1 I0 When connecting there are some indicative tones from Handsfree short press K2 to receive the conn
9. RF exposure limits set forth for an uncontrolled environment The equipment must not be co located or operating in conjunction with any other antenna or transmitter HFB300manual GB 15 05 2008 15 54 Pagina 5 C Iu ENGLISH Contents 1 INTRODUCTION 1 1 Bluetooth Technology I INTRODUCTION 4 Bluetooth is an internationally standardized technology supporting short distance wireless com I 1 Bluetooth technology 4 munications Any two Bluetooth compatible equipments such as mobile phone PDA PC headset I 2 Bluetooth handsfree system 4 mouse keyboards printer etc can wirelessly communicate with each other via Bluetooth connec l 3 Product features 4 tion To ensure worldwide compatibility Bluetooth operates on the globally available ISM Industrial I 4 Package content 5 Scientific and Medical frequency band Within 2 4 GHz and 2 48 GHz Bluetooth transmits data up l 5 Overview 5 to either 10 meters CLASS Il mode or 100 meters CLASS mode using 79 frequency hopping 1 6 Definitions on key press duration 5 channels Though line of sight is not required Bluetooth connections could be subject to interferences from 2 USING YOUR HANDSFREE 6 obstructions such as walls human bodies and other electronic devices In addition due to varia 2 Battery charging and usage 6 tions on product implementation it is likely that Bluetooth equipments from different manufactu 2 1 1 Battery charging 6 res have interoperability iss
10. The company reserves rights to make any changes and improvements to the product described in Warning Users should not make changes or modify the device in any way Changes or modifica this document without prior notice tions without expressly approved by the party responsible for compliance could void the user s authority to operate the device Notice Please make sure your mobile phone supports Bluetooth profiles and network operator supports This device complies with part 15 of the FCC Rules Operation is subject to the following two the functions described in this manual otherwise the relative functions cannot be realized on this conditions 1 This device may not cause harmful interference and 2 this device must accept any Handsfree device interference received including interference that may cause undesired operation Safety Use the charger that comes with package FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT Check the laws and regulations on the use of mobile phones and handsfree equipment in the This equipment has been tested and found to comply with the limits for a Class B digital device areas where you drive Always give full attention to driving and pull off the road and park before pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection making or answering a call if driving conditions require against harmful interference in a residential installation This equipment generates
11. andsfree Profile the Bluetooth connection between two equipments shall be established in advance If two Bluetooth equipments have been paired recently you can simply reconnect them Connecting your Handsfree with Bluetooth Handset Initiating a request from either the handsfree or the handset can set up Bluetooth connection The detailed operations are as follows Initiating connection request from the Handsfree Place the handsfree close to the Bluetooth handset and then short press K2 2 Initiating connection request from the Bluetooth handset Place the handsfree close to the Bluetooth handset and then follow the handset user guide to find the handsfree and send connection request After connecting you will hear a connecting tone and then Blue LED gives 3 quick blinks per 2 seconds Disconnecting your Handsfree with Bluetooth Handset When handsfree connected with bluetooth handset you can disconnect them as follows Long press K2 2 Refer to handset s manual to initiate the connection from the handset side After disconnecting you will hear a disconnecting tone and then Blue LED gives blink per 3 seconds 2 5 Call Functions 2 5 1 Call Before dialing both your handsfree and handset must be power on And you also need to ensure your handsfree and handset has been linked with Bluetooth connection Answer Call Short press K2 Reject Call Long press K4 End Call Short press K2 Redial Long press K3 The
12. dsfree can not be found when a handset tries to pair with it Your handsfree may not be in the pairing mode please refer section 2 4 1 for details 8 Do the paired handsfree or the paired handset need to be repaired power off No Please note that for the handset supports handsfree profile the handsfree and the handset must be connected first Refer section 2 4 4 for details 9 Voice dialing does not work First check the handset supports voice dialing function make sure you have recorded the voice tag Please note that noisy environment will affect voice dialing 10 Can t realize any functions In the course of using sometimes the Handsfree cannot work properly by some wrong opera tions At this time connect the charger to the power outlet plug the mini USB connector of the charger to handsfree s charging port to start charging for a few seconds Then release the charger from the handsfree and the power outlet and turn on the handsfree to restart WWW CALIBER NL HFB300manual GB 15 05 2008 15 54 Pagina 3 C Iu ENGLISH Declaration Certification and Safety Approvals Without written permission from original manufacturer reproduction transfer distribution or This product has been tested and found to comply with Bluetooth BOB requirements part 15 of storage of part or all of the contents in this document in any form is prohibited FCC rules R amp TTE Directive 99 5 EC or CE marked requirements
13. ection Il After connected start your Skype and configure the audio interface to be Bluetooth AV HS Audio Then you can chat via Online Messenger or VoIP software S ION Skype IN Options gee General Audio In Windows default device n Privacy Audio Out Windows default device Windows default device Realtek AC97 Audio Bluetooth AV HS Audio A Sounds Ring PC speaker Notifications Ringing v Let Skype adjust my sound device settings Sound Devices H Hotkeys ey Connection Xx Advanced f Call Forwarding amp Voicernail o Learn more how to set up your audio settings amp Make a test call to Skype answering machine Save Cancel If the driver you used is not IVT BlueSoleil such as the software that comes with package please referring to the user guide lt gt HFB300manual GB 15 05 2008 15 54 Pagina 15 ENGLISH ae 3 QUICK USER GUIDE 3 1 LED patterns LED Pattern Blue LED gives blink per 3 seconds Red LED is off LED Pattern 2 Blue LED gives 3 quick blinks per 2 seconds Red LED is off LED Pattern 3 Blue and Red LEDs alternate continuously LED Pattern 4 Blue and Red LEDs alternate every 3 seconds LED Pattern 5 All LEDs are off 3 2 Quick User Guide You can follow the instructions listed in Table 1 6 below to operate your handsfree devices Please refer section 1 5 and 1 6 for details of key and k
14. ed call functions 10 2 6 Connecting your handsfree with USB dongle E 1 3 Product Features i e Bluetooth vl 2 compliant interference tolerable with WLAN devices 2 Quick User guide e Class Il operation range up to 10 meters 3 Led patterns 13 ee eh eee l e Best in class voice quality ensured by cutting edge noise suppression and echo cancellation 3 2 Quick user guide 13 techniques 4 E EE 16 Voice dialing and user friendly operation keys ideal for car drivers to make receive calls Supports call waiting conference functions 5 Important messages and frequently asked questions 17 Se ee een Better portability with internal rechargeable Li ion battery e Talk standby time up to 5 5 500 for HFB 300 hours with internal battery e Easy to mount with stylish mounting dock Sun visor Clip hang strip and Double side Sticker Robust performance fast connection accurate and sensible search of devices in range Stylish portable lightweight mini sized suitable for vehicle and office environment HFB300manual GB 15 05 2008 15 54 Pagina 7 ENGLISH ae 1 4 Package Content HFB 300 Mounting dock Optional Double Side Sticker Sun visor Clip Optional e 12 24V Car Charger or Traveling Charger Optional User Manual 1 5 Overview 2 Red Blue LED 8 Charging Port I Speaker 6 Button K4 4 Button K2 5 Button K3 3 Button KI 7 Microphone l Speaker 2 Red Blue LED f
15. ey press duration definitions Note your handsfree devices can only talk to paired Bluetooth handsets For handsets supporting HFP only you also need to establish Bluetooth connection between your handsfree and your phone before making and answering calls Table Power on off FUNCTION CURRENT STATUS OPERATION HANDSFREE INDICATOR HANDSET o O AUDIO TONE LED INDICATOR Table 2 Pairing Connections FUNCTION CURRENT STATUS OPERATION HANDSFREE INDICATOR CO Power Off Very long press KI 2 power up tones and then pairing tone mE Pairing Mode Long press K4 NENNEN LED Pattern Power on Pairing Mode Follows your handset connecting tone LED Pattern 2 user guide to complete pairing procedure Passkey is 0000 Short press K2 or setup connection from the handset Enter LED Pattern 3 pairing mode Erase all paired profiles Pair handsfree with handset Connect LED Pattern 2 handsfree with handset Disconnect Standby connect Table 3 Call Functions connecting tone EE m HANDSFREE INDICATOR disconnected disconnected Standby connect Long press K2 or refer to handset s manual to initiate the connection from the handset side FUNCTION CURRENT STATUS OPERATION HANDSET AUDIO TONE LED INDICATOR Ln I E a E we wc E G sod oc Ro Rs I M Voice Dialing Standby Standby Long press K4 LED Pattern 2 Cancel Voice Voice Dialing Voice Dialing Short press K4 Key Tone LED Pattern
16. nd wrap or melt the certain plastics HANDSET ae AUDIO TONE LED INDICATOR Do not store the device in too cold place under 5 C Moisture could form inside E the device when you take it to a warm place This could damage the internal electronic circuits ow power Except power Beep every 20 seconds LED Pattern 4 i i warning off e Avoid dropping knocking and shaking the device The mechanical parts and the internal electronic circuits could be broken Table 6 Advariced Call Functions Avoid using hash chemicals cleaning solvents and any other strong detergent to clean the device You may use a clean and slightly damp cloth to clean the device lt FUNCTION CURRENT STATUS OPERATION HANDSFREE INDICATOR Always take to device to the nearest authorized service facility for repairing if it is malfunctioning Disassembling modifying and replacing components yourself could degrade HANDSET HF LED INDICATOR product performance cause damages and terminate warranty Held active Talk Call Waiting Long press K3 LED Pattern 2 call and accept incoming call End active call Talk Call Waiting Short press K2 LED Pattern 2 and answer new call Toggle held call Talk Call on hold Long press K3 LED Pattern 2 and active call End active call Talk Call on hold Short press K2 LED Pattern 2 and accept hold call Conference Talk Call on hold Long press K4 LED Pattern 2
17. or indicating device status 3 Button KI for turning on off device 4 Button K2 for receive end call 5 Button K3 for adjusting speaker volume up 6 Button K4 for adjusting speaker volume down 7 Microphone for picking up your voice 8 Charging Port for connecting to the travel or car charger to charge the battery of device 6 Definitions on Key Press Duration Short press SP press and release a button quickly Long press LP press and hold a button for at least 3 seconds then release Very long press VP press and hold a button for at least 6 seconds then release 2 USING YOUR HANDSFREE 2 1 Battery Charging and Usage 2 1 1 Battery Charging This device contains a rechargeable Li Polymer battery First time charging time is about 4 hours Later on recharging time is around 2 3 hours Detailed charging procedures as follows Connect the car charger to the cigarette lighter 2 Plug the USB Cable in PC 3 Referring to Figure 2 plug the connector of the charger to handsfree s charging port to start charging Both the Red and Blue LEDs will be on during charging Once the Red LED turns off the battery is fully charged and you should disconnect the charger from the handsfree and the power outlet Note It is recommended to charge your device when it is not in use 2 Please note that inserting charger will cause a device reset When the device is in charging the
18. s If your mobile phone has call waiting conference functions this Bluetooth Handsfree can support the function by following operations I A new call comes in While you are in talk Long press K3 to hold active call and accept incoming call 2 Short press K2 to end active call and answer new call 2 When two calls in progress one is active and the other is on hold Long press K3 to toggle hold call and active call 2 Short press K2 to end active call and accept hold call 3 Long press K4 to make conference The Blue LED gives 3 quick blinks per 2 seconds and the Red LED is off 15 05 2008 15 54 Pagina 13 HFB300manual GB ENGLISH 2 6 Connecting your Handsfree with USB Dongle Before pairing and connecting you must ensure the USB Dongle has already connect with PC and IVT BlueSoleil driver has been installed in PC Detailed operation procedures are as follows Press and hold KI for at least 6 seconds until the Blue and Red LEDs alternate continuously You will hear 2 power up tones 2 more power up tones to indicate that the Handsfree has successfully entered the paring mode 2 Start IVT BlueSoleil Click My Bluetooth gt Bluetooth Device Discovery on main menu to search the Bluetooth device in range 3 In the result of search right click BTHF202 and choose Pair Device X IFI Corporation BlueSoleil Nain Window File View My Bluetooth My Services Tools Help OS Ea B
19. s that a unique and encrypted wireless link between your handsfree and handset will be used during calls Detailed operation procedures are as follows Place your handsfree close to your Bluetooth handset and ensure your handsfree is power off your handset is power on 2 Press and hold KI for at least 6 seconds until the Blue and Red LEDs alternate continuously You will hear 2 power up tones and a pairing tone to indicate that the handsfree has successfully entered the paring mode 3 Following your phone user guide to active Bluetooth device search on the phone side on your phone screen you will see a list of Bluetooth equipment found by the phone at the end of the searching process 4 Select this Bluetooth Handsfree from the list for HFB 300 the sign is BTHF202 and initiate pairing following handset s on screen prompts 5 Continue to follow on screen prompts to enter passkey 0000 and confirm to pair the hands free with your handset Once the pairing procedure is completed you will hear a connecting tone and then Blue LED gives 3 quick blinks per 2 seconds It indicates that the handsfree device and the handset are paired and connected Note If pairing is successful handsfree s Red LED is off The Blue LED gives 3 quick blinks per 2 seconds If paring is failed the Blue and Red LEDs alternate continuously for about 2 minutes You need to go back to above steps 3 5 to repeat the paring process 2 Your handsfree will
20. ues In that case you may consult with manufactures to check product 2 1 2 Battery information 6 compatibility 2 2 Mounting your handsfree 7 2 3 Turn ON OFF handsfree turn 8 Note that there could be some restrictions imposing on using Bluetooth devices in some coun 2 4 Pairing Connecting your handsfree with bluetooth equipment 8 tries Please check with your local authorities 2 4 1 Pairing your Handsfree with Bluetooth handset 8 2 4 2 Pairing your Handsfree with Other Bluetooth Equipment 8 1 2 Bluetooth Handsfree System 2 4 3 Erase all Paired Records 3 This Bluetooth handsfree system is a specially designed product allowing car drivers to make and 2 4 4 Connecting Disconnecting your Handsfree with Bluetooth Equipment receive calls without holding a mobile phone It provides a clean wireless audio connection with 2 5 Call functions 9 your Bluetooth mobile phone and PDA The product can also be used in the office or home besi 2 5 Call 9 des of vehicle environment 2 5 2 Adjusting handsfree volume 10 In addition to vehicle environment applications this portable equipment supported by an internal 2 5 3 Mute i rechargeable Li ion battery can also be used in office environment as normal handsfree equipment 2 5 4 Transferring calls to from your handset 10 to make receive phone calls without bothering holding the mobile handset It can also be placed 2 5 5 Voice dialing 10 beside a Bluetooth enabled PC to make voice calls over the Internet 2 5 6 Advanc
Download Pdf Manuals
Related Search