Home

English-US

1. Troubleshooting guide TROUBLE TROUBLESHOOTING TIP been connected securely into wall outlet or grounded extension cable or strip Power switch should be in the ON position and LED is lit Check that the Brightness and or the Contrast adjustments of the Display have not been turned down to minimum levels NO SIGNAL The signal cable should be completely message on screen connected to the video card computer The video card should be completely seated in its slot and the computer is switched ON Display image is not centered too small or too large in PC mode Vertical or Horizontal noise is present in the picture Adjust Clock and Phase in the OSD Push the down key in front side or Auto key in remote controller WEEE Symbols Correct Disposal of This Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of w
2. a damp cloth for cleaning and do not allow moisture or liquids to enter vents 32 Attachments Use only UL Listed Vicon recommended attachments to prevent unit damage and personal injury 33 Water and Moisture Use only products designed for outdoor environments where they will be exposed to water or moisture 34 Accessories Do not place the unit on an unstable surface to avoid falling Use only UL Listed Vicon recommended mounting accessories 35 Ventilation Do not block ventilating slots and openings as they ensure reliable operation Do not place the unit near a heat source or into an enclosure unless recommended by Vicon 36 Grounding Only products equipped with a 3 prong grounded plug should be inserted into a grounded power outlet Contact an electrician to replace an obsolete outlet Do not force a plug into a non grounded outlet 37 Power Cord Protect ion Power supply cords should not be routed in trafficked areas or in tight spaces where they will be pinched or used to bear weight Allow some slack in the cord where it enters the unit 38 Lightning Disconnect the product from its power source and cable system when possible to prevent damage due to lightning and power line surges 39 Power Lines e Do not locate outside cables over power or utility lines where they can fall and make direct contact Contact with power lines can be fatal 40 Overloading Do not overload wall outlets and extension cord
3. ee erie amete asus Bo PU um Et Eee RU 18 WM A P uno 19 This Monitor was Manufactured by ISO 9001 Certified Factory Important Safeguards Indoor Use GRAPHIC SYMBOL EXPLANATION The lightning bolt symbol alerts the user to the presence of dangerous voltage that may present the risk of electric shock CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRICAL SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The exclamation point symbol alerts the user to the presence of important operating and maintenance instructions WARNING To reduce a risk of fire or electric shock do not expose this product to rain or moisture 26 Read Instructions Read all safety and operating instructions before the product is operated 27 Retain Instructions Retain all safety and operating instructions for future reference 28 Heed Warnings Pay attention to all product warnings 29 Follow Instructions Follow all operating instructions 30 Installation and W iring The equipment and all devices connected to it shall be installed and wired in accordance with the National Electrical Code ANSI NFPA 70 31 Cleaning Do not use caustic abrasive or aerosol cleaners a For units that CAN BE DISCONNECTED from the power source use a damp cloth for cleaning b For units that CANNOT BE DISCONNECTED from the power source use
4. its front facing downward on a soft cloth A 2 Assemble the Stand Base into the Stand Body in the correct direction using the included screws in the accessory box e Stand Base Stand Body FS4x12 screws A 3 Once assembled take the monitor up carefully and face the front side B Positioning your display Adjust the position of the panel in various ways for maximum comfort Tilt Range 3 15 ud 15 N N Connecting with external equipment Rear Connection DC12V IN AUDIO IN VGA DVI HDMI pU op quee Controls and functions FRONT KEY CONTROL SOURCE jo MENU AUTO y Pr f P TT 1 SOURCE 3 Selects VGA DVI and HDMI inputs Selects an option in the OSD 2 MENU EXIT Activates or exits the OSD Moves previous menu or status in the OSD 3 AUTO VW and A Moves another option in the OSD The up A button converts the aspect ratio as 16 9 or 4 3 The Auto A button is auto adjustment function in the VGA input 4 VOL lt gt Adjust the volume and menu settings The VOL button is the Sound off function 5 I Turns the power ON or OFF There will be a few seconds delay before the display appears 6 POWER LED Turned on Blue color No signal Red color Turned off LED off Controls and functions OSD MENUS All monitor pages sound and settings can be adjusted and changed from OSD menus How to Adjust SD Menu 1 Press the PAIRING MENU button to enter the OSD men
5. will not occur in a particular installation If this equipment does cause interference to radio and television reception which can be determined by turning equipment off and on the user is encouraged to try and correct the interference by one or more of the following measures Reorient the receiving antenna Relocate the equipment with respect to the receiver Relocate the equipment away from the receiver Plug the equipment into a different electrical outlet so that the equipment and receiver are on different branch circuits If necessary the user should consult the dealer or an experienced radio television technician for additional suggestions The user may find the following booklet prepared by the Federal Communications Commission helpful Interference Handbook Bulletin CIB 2 This booklet is available from the U S Government Printing Office Superintendent of Documents Mailstop SSOP Washington D C 20402 9328 ISBN 0 16 045542 1 N Warning Power must be removed from this unit before removing circuit modules or cables ZN Caution This unit contains circuit cards with integrated circuit devices that can be damaged by static discharge Take all necessary precautions to prevent static discharge Installation Before setting up the monitor ensure that the power to the monitor and other attached devices are turned off X Notice Stand screws are optional A Connecting the stand A 1 Place the monitor with
6. Installation and Operation Manual XX 204 55 00 VM 6215LED 1 High Definition LED Monitor LISTED Commercial CCTV Video Equipment 2C88 Vicon Industries Inc 131 Heartland Boulevard Edgewood NY 11717 Tel 631 952 2288 Fax 631 951 2288 Toll Free 1 800 645 9116 24 Hour Technical Support 800 34 VICON 800 348 4266 UK 44 0 1489 566300 Vicon Industries Inc does not warrant that the functions contained in this equipment will meet your requirements or that the operation will be entirely error free or perform precisely as described in the documentation This system has not been designed to be used in life critical situations and must not be used for this purpose WWW Vicon security com Document Number 8009 8204 55 00 Issued 0614 Product specifications subject to change without notice Copyright 2014 Vicon Industries Inc All rights reserved Contents Important Safeguards nenne 23 Do A A on ES E E ee 4 ESO NOC O ee ee E E E 5 liic m 6 Connecting with external equipment ccccconcnncccccconcccnnnnoconncnnnnnoncnnonannnnnnnannnnnnanonononanenoss 1 Controls a a MAC ONS RR ee po 12 Mounting QUITE T n 13 D SUB connector pin assignment anne een 14 Power management E ee a 15 A ee een 16 IMjeFe iesiiece 17 v1 9 8 lace Ios PHP ONE usse iata andi teaches aceti
7. WIDE OSD TIMER INPUT SELECT gt HDMI Om v R iY El NO HDMI HDMI 1928x1888 68Hz 1928x1888 6BHz Options Functions Value Korean Japanese Chinese English German French Spanish Italian OSD Horizontal Moves OSD left right on the screen 0 100 White Balance Adjusts color automatically Yes No Input Select Selects input signal VGA DVI HDMI Factory Reset Resets monitor setting Yes No DCR Dynamic Contrast Ratio The language of OSD menu can be Language di selected 12 Mounting Guide WALL MOUNTING OPTIONAL The LCD monitor is suitable for wall mounting by using the VESA 100 standard wall mount not included in the delivery M4x10 screws ZN Attention You must use four M4x10 screws to assemble this monitor and the wall mount bracket AN Warning If user use longer than M4x10 it may cause the damage on the unit Please follow instructed bolt size amp length AI D SUB connector pin assignment gt PIN ASSIGNMENTS 3 BLUE VIDEO 11 GROUND 4 GROUND 12 SDA for DDC 5 GROUND 13 H SYNC or H V SYNC 6 RED GROUND 14 V SYNC 7 GREEN GROUND 15 SCL for DDC 8 BLUE GROUND D SUB ACCESSORIES Power cord Power adaptor User manual HDMI Cable Stand FS4x12 screws 2EA Stereo cable Wall mount Optional SAS GUN e Ads Power management This monitor features a power management system to power down upon recei
8. ding d Circuit Overloading Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring Appropriate consideration of equipment nameplate ratings should be used when addressing this concern e Reliable Earthing Reliable earthing of rack mounted equipment should be maintained Particular attention should be given to supply connections other than direct connections to the branch circuit e g use of power strips Cautions CAUTION The power supply cord is used as the main disconnect device ensure that the socket outlet is located installed near the equipment and is easily accessible ATTENTIONN Le cordon d alimentation est utills comme interrupteur g n ral La prise de courant doit tre situ e ou install e proximit du mat riel et tre facile d acces CAUTION TO SERVICE PERSONNEL POWER SUPPLY CORD IS USED AS MAIN POWER DISCONNECT DEVICE IN THIS PRODUCT UNPLUG THIS PRODUCT FROM THE WALL OUTLET BEFORE REMOVING THE BACK COVER AND SERVICING EMISSION CHARACTERISTICS TESTED BY SEMKO THIS PRODUCT HAS BEEN TESTED AND HAS SHOWN COMPLIANCE WITH THE NATIONAL SPECIFICATIONS SUCH AS SWEDISH MPR 1990 10 MPR gt NEVER REMOVE THE BACK COVER Removal of the back cover should be carried out only by qualified personnel DO NOT USE IN HOSTILE ENVIRONMENTS To prevent shock or fire hazard d
9. e Company and the return shipment is prepaid in accordance with policy The Company will not be obligated to repair or replace equipment showing abuse or damage or to parts which in the judgment of the Company are not defective or any equipment which may have been tampered with altered misused or been subject to unauthorized repair Software supplied either separately or in hardware is furnished on an As Is basis Vicon does not warrant that such software shall be error bug free Software support via telephone if provided at no cost may be discontinued at any time without notice at Vicon s sole discretion Vicon reserves the right to make changes to its software in any of its products at any time and without notice This Warranty is in lieu of all other conditions and warranties express or implied as to the Goods including any warranty of merchantability or fitness and the remedy specified in this Warranty is in lieu of all other remedies available to the Purchaser No one is authorized to assume any liability on behalf of the Company or impose any obligations on it in connection with the sale of any Goods other than that which is specified above In no event will the Company be liable for indirect special incidental consequential or other damages whether arising from interrupted equipment operation loss of data replacement of equipment or software costs or repairs undertaken by the Purchaser or other causes This warranty ap
10. here and how they can take this item for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal 7 Shipping Instructions Use the following procedure when returning a unit to the factory 1 Call or write Vicon for a Return Authorization R A at one of the locations listed below Record the name of the Vicon employee who issued the R A Vicon Industries Inc 131 Heartland Boulevard Edgewood NY 11717 Phone 631 952 2288 Toll Free 1 800 645 9116 Fax 631 951 2288 For service or returns from countries in Europe contact Vicon Industries U K Ltd Brunel Way Fareham PO15 5TX United Kingdom Phone 44 0 1489 566300 Fax 44 0 1489 566322 2 Attach a sheet of paper to the unit with the following information Name and address of the company returning the unit Name of the Vicon employee who issued the R A R A number Brief description of the installation Complete description of the problem and circumstances under which it occurs Unit s original date of purchase if still under warranty Q 90 02 09 UG 3 Pack the unit carefully Use the original shipping carton or its equivalent for maximum protection 4 Mark the R A number on the outside of the carton on the shipping label 18 Vicon Standard Equipment Warranty Vicon Ind
11. ncorporated into the site wiring b For 230 VAC units with a plug the outlet must be installed near the unit and be easily accessible 48 For Devices Requiring a Separate Power Supply All devices requiring a separate power supply shall be powered by a UL Listed Class 2 Power Supply 49 Lithium Batteries Only WARNING Fire and burn hazard Do not recharge disassemble heat above 212 F or incinerate Keep battery out of reach of children and in original package until ready to use Dispose of used batteries promptly Risk of explosion if battery is replaced by incorrect type Dispose of used batteries according to the instructions 50 For Rack Mounted Units Only The following precautions apply to all rack mounted units a Elevated Operating Ambient If installed in a closed or multi unit rack assembly the operating ambient temperature of the rack environment may be greater than room ambient Therefore consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature Tma specified by the manufacturer NT Important Safeguards Indoor Use Cont b Reduced Air Flow Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised c Mechanical Loading Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loa
12. o not expose the unit to rain or moisture This unit is designed to be used in the office or home Do not subject the unit to vibrations dust of corrosive gases KEEP INAWELL VENTILATED PLACE Ventilation holes are provided on the cabinet to prevent the temperature from rising Do not cover the unit or place anything on the top of unit gt AVOID HEAT Avoid placing the unit in direct sunshine or near a heating appliance TO ELIMINATE EYE FATIGUE Do not use the unit against a bright back ground and where sunlight or other light sources will shine directly on the monitor BE CAREFUL OF HEAVY OBJECT Neither the monitor itself nor any other heavy object should rest on the power cord Damage to a power cord can cause fire or electrical shock FCC Notice Note Complies with Federal Communications Commission Rules amp Regulations Part 15 Subpart B for a Class A digital device WARNING This equipment generates and uses radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instruction may cause interference to radio and television reception It has been type tested and found to comply with the limits for a Class A computing device in accordance with the specification in subpart B of part 15 of the FCC rules which are designed to provide reasonable protection against such interference in a commercial installation However there is no guarantee that interference
13. plies to all sales made by the Company or its dealers and shall be governed by the laws of New York State without regard to its conflict of laws principles This Warranty shall be enforceable against the Company only in the courts located in the State of New York The form of this Warranty is effective May 4 2012 THE TERMS OF THIS WARRANTY APPLY ONLY TO SALES MADE WHILE THIS WARRANTY IS IN EFFECT THIS WARRANTY SHALL BE OF NO EFFECT IF AT THE TIME OF SALE A DIFFERENT WARRANTY IS POSTED ON THE COMPANY S WEBSITE WWW VICON SECURITY COM IN THAT EVENT THE TERMS OF THE POSTED WARRANTY SHALL APPLY EXCLUSIVELY 19 MEMO Vicon Industries Inc VICON INDUSTRIES INC 131 HEARTLAND BLVD EDGEWOOD NY 11717 8315 www vicon security com 631 952 2288 1 800 645 9116 Fax 631 951 2288 Vicon Europe Headquarters Brunel Way Fareham PO15 5TX United Kingdom 44 0 1489 566300 Fax 44 0 1489 566322 Vicon Germany Kornstieg 3 D 24537 Neumuenster Phone 49 0 4321 8790 Fax 49 0 4321 879 97 Far East Office Unit 5 17 F Metropole Square 2 On Yiu Street Shatin New Territories Hong Kong 852 2145 7118 Fax 852 2145 7117 Internet Address www vicon security com L39ME0366 REV 00
14. pt ofthe VESA DPMS The display power management signaling from a VESA DPMS video card The VESA DPMS compliant video card performs this signaling system through not sending horizontal vertical or sync signal This monitor enters an appropriate mode through identifying each of the three modes of the signaling system POWER CONSUMPTION Mode Power Consumption No Si o Signal amp Aw Turned Off LED INDICATOR The power management feature of the monitor is comprised of three stages Turned on blue no signal red and turned off LED off Mode LED Monitor Operation Turned On Blue Normal Operation No Signal R Not Operation ed Turned Off Off Not Operation a4 Ga Specifications 21 5 Diagonal AM TFT Type Active Matrix Pixel pitch mm 0 24825 H x 0 24825 V LCD Brightness 250cd m Typical Contrast ratio 1000 1 Typical Viewing angle 170 160 H V Resolution H x V 1920x1080 60Hz E Horizontal 31 80kHz requenc Vertical 56 75Hz Digital Visual Interface DVI 1 0 amp HDCP 1 2 VGA RGB PC HDMI Visual Interface HDMI 1 3 Active Displa id 476 64mm x 268 11mm Area H x V Packing Dimensions 565mm x 415mm x 125mm WxHxD 22 24 x 16 34 x 4 92 Net 4 67 kg 10 3 Ibs Gross 6 47 kg 14 26 Ibs 12V 2 1A Electrical Ratings 100 240V 50 60Hz gt gt NOTE Technical specifications are subject to change without notice 16
15. s to prevent risk of fire and electric shock 41 Object and Liquid Entry Never probe through or spill liquid into enclosure openings to prevent risk of fire or electric shock 42 Servicing Refer all servicing to qualified service personnel 43 Damage Requiring Service Obtain service when a The power supply cord or plug is damaged b Objects have fallen or liquid has been spilled into the product c The product is not designed for outdoor use and has been exposed to water or moisture d The product does not operate per the operating instructions Perform Vicon recommended adjustments modifications and troubleshooting only to avoid unit damage and personal injury e The product has been dropped f The product shows a significant change in performance 44 Replacement Parts Use only Vicon specified replacement parts or an approved equivalent to prevent unit damage and injury 45 Safety Check Request safety checks to be performed following repair or maintenance to verify proper operation 46 ESD Precaution Take all normal electrostatic discharge precautions to avoid component damage during installation and operation 47 For 230 VAC Devices Only When the disconnect device is not incorporated in the equipment or when the plug on the power supply is intended to serve as the disconnect device follow the guidelines below a For permanently connected 230 VAC units a readily accessible disconnect device must be i
16. u Find the item you desire using AUTO W A buttons Press SOURCE G3 button to go to the sub menus Change to the value you desire using lt gt button Return to the higher menu level using PAIRING MENU Press PAIRING MENU button to get out of OSD Menu Ox pr 2 99 mw 1 PICTURE e S BAIGHTNESS Om if 58 CONTRAST 3 Clas E 50 GAMMA r OD Options Functions Value Brightness The brightness of screen can be adjusted 0 100 The contrast of screen can be adjusted 0 100 Gamma The Gamma of screen can be adjusted 0 50 Controls and functions 2 COLOR COLOR PRESET ML je sRGB 6500K 9300K RED Om E GREEN EL MEE BLUE EL NENNEN Red Red color ofthe screen is adjusted 0 100 10 Controls and functions 3 TRACKING PHASE VERTICAL ee Col CH o Options Functions Value Horizontal The screen moves Left or Right 0 100 Vertical The screen moves Up or Down Clock Adjusts the vertical noise of screen image Phase Adjusts the number of horizontal picture elements Sharpness Adjust sharpness of the picture 4 VOLUME VOLUMI VOLUME ome JE 59 Options Functions Value Audio volume is adjusted 0 100 Mute Audio volume is muted ON OFF 11 Controls and functions 5 SET UP SETUP LANGUAGE gt ENGLISH WHITE BA OSD HORIZONTAL a Cima JE 58 DER OFF 0SD VERTICAL amp e Cm 4 3 OR WIDE b
17. ustries Inc the Company warrants your equipment to be free from defects in material and workmanship under Normal Use from the date of original retail purchase for a period of three years with the following exceptions 1 Monitors all models One year from date of original retail purchase 2 Uninterruptible Power Supplies Two years from date of original retail purchase 3 VDR 700 Recorder Series One year from date of original retail purchase 4 V5616MUX One year from date of original retail purchase 5 Arecont Cameras One year from date of original retail purchase 6 FMC series fiber optic media converters and associated accessories Lifetime warranty 7 For PTZ cameras Normal Use excludes prolonged use of lens and pan and tilt motors gear heads and gears due to continuous use of autopan or tour modes of operation Such continuous operation is outside the scope of this warranty 8 Any product sold as special or not listed in Vicon s commercial price list One year from date of original retail purchase Date of retail purchase is the date original end user takes possession of the equipment or at the sole discretion of the Company the date the equipment first becomes operational by the original end user The sole remedy under this Warranty is that defective equipment be repaired or at the Company s option replaced at Company repair centers provided the equipment has been authorized for return by th

English-US

Contents

Download Pdf Manuals

Related Search

Related Contents