User Manual Of Smart Charger (２０A) for 51.2V (16
Contents
1. terminal with Included 1 pcs SOA Andersen connector Make sure the charge DIY wire will be acceptable for 20A Max charge current Warning Wrong polarity will damage the charger and Batteryspace are not responsible for the damage or losses caused by misusing Note Anderson connector has no difference in male and female which can mate each other CHARGE E The Battery range is between 20AH to 120AH M Reverse Polarity Protection M Short Circuit Protection E No trigger voltage requirement Built in cooling fan to ensure charger long service life Nx Dmension LxWxH 282mm 11 1 x 158nm 6 2 x 78nm 3 1 Mix Wight 8 Olbs 0 6 3650erams How to use 1 Turn on Make sure the pack voltage is suitable for charger Then connect to the pack with correct polarity 2 Check the voltage of the AC input is suitable for the input voltage of the charger or not 3 The charger start ramp charging after auto testing in 1 minutes 4 Indicating LED signification 5 Power indicating and battery test LED Green LED Fully charged Correct Polarity Connection Red LED Charging Wrong polarity Connection Orange LED 90 fully charged 6 Turn off After Battery is fully charged must disconnect the AC power supply before disconnect battery Operation environment Above the sea level lt 2000m Ambient temperature 10 C 50 C Ambient humidity 5 70 RH Storage temperature 10 C 60 C Without conductive dust Without ex2. User Manual Of Smart Charger 20A for 51 2V 16 cells LiFeP04 Battery Pack 110V only SB50A Anderson connect or AA Portable Power Corp AA Portable Power Corp http www batteryspace com Address 825 S 19 St Unit A Richmond CA 94804 Tel 510 525 2328 Fax 510 439 2808 Email Sales batteryspace com Prepared amp Approved by RongW i Liu 06 18 12 a mon If failure or error of this instrument could result in a critical accident of the system install a external protection circuit to prevent such an accident In order to prevent instrument damage or failure protect the power line and the input output lines from high currents by using fuses with appropriate ratings Power supply In order to prevent instrument damage or failure supply power of the specified rating In order to prevent electric shock or instrument failure do not turn on the power supply until all of the wiring is completed Never use the instrument near inflammable gases In order to prevent fire explosion or instrument damage never use this instrument at a location where inflammable or explosive gases or vapour exist Never touch the inside of the instrument In order to prevent electric shock or burns never touch the inside of the instrument only authorized service engineers can touch the inside of the instrument to check the circuit or to replace parts High voltage and high temperature sections inside the instrument are extremely da
3. ngerous Never modify instrument In order to prevent accident or instrument failure never modify the instrument Maintenance In order to prevent electric shock burns or instrument failure Only authorized service engineers may replace parts In order to use this instrument continuously and safely conduct periodic maintenance Some parts used in this instrument have a limited service life and may deteriorate over time Wiring precautions Introduction AA Portable Power Corp http www batteryspace com specialized in the research amp development of the intelligence battery charger in the long terms The series battery charger is based on MCU technology with pulse charging mode the charging voltage has temperature compensation automatically It could be used in the various electric cars the field of tourism railway mine post and telecommunication Main Feature INPUT m AC input voltage 99 to 121 VAC single phase E Input frequency 45 to 63 Hz E Efficiency 72 min at rating power 115Vac 60Hz OUTPUT mM CCCV charging mode E Cut off voltage 58 2VDC E 204 current Max E Charge terminal 4 long 8AWG wire SBD0A Andersen connector SP50A Anderson plug dimension LxWxH 1 9 48 0mm x 1 5 38 Omm x 0 6 15 Omm Included 1 pcs 1 9 x 1 5 x 0 6 SBDOA Anderson connector without wire for DIY use Tip In order to match up the charger s connector You may connect the battery pack charge
4. plosive dust Without corrosive gas and steam damaged to metal and isolator keep away from rain and snow OAE A E A A AE IE aE i Mounting slop S5 degree Maintenance and service The charger must be set at ventilated dry and dust less place to prevent the reduction of the performance of the charger For technical support please contact us via sales batteryspace com
Download Pdf Manuals
Related Search