MMT225 User`s Manual VA1_20100120
Contents
1. MMT225 User s Manual 3 3 Bluetooth optional The MMT225 provides users to extra add Bluetooth function Users can install the Bluetooth driver under the operating system Windows XP To facilitate installation of the touch screen driver you should read the instructions in this chapter carefully before you attempt installation 1 Insert Driver CD and follow the path to select the Drivers XP Step 2 Bluetooth optional Step 2 Bluetooth optional 2 Double chick the icon Setup a setup 3 Follow the installing procedure and press OK 24 Drivers Installation2. sensitive components that the MMT225 must be properly grounded The brightness of the flat panel display will be getting weaker as a result of frequent usage However the operating period varies depending on the application environment Turn OFF the system power before cleaning Clean the system using a cloth only Do not spray any liquid cleaner directly onto the screen Although the touchscreen is chemical resistant it is recommended that you spray the liquid cleaner on a cloth first before wiping the screen Avoid using sharp objects to operate the touchscreen Scratches on the touchscreen may cause malfunction or internal failure to the touchscreen The flat panel display is not susceptible to shock or vibration When assembling the MMT225 make sure it is securely installed Do not open the system s back cover If opening the cover for maintenance is a must only a trained technician is allowed to do so Integrated circuits on computer boards are sensitive to static electricity To avoid damaging chips from electrostatic discharge observe the following precautions Before handling a board or integrated circuit touch unpainted portion of the system unit chassis for a few seconds This will help to discharge any static electricity on your body When handling boards and components wear a wrist grounding strap available from most electronic component stores Trademarks Acknowledgments AXIOMTEK is a trademark of
3. AXIOMTEK Ltd PC AT VGA are trademarks of International Business Machines Corporation Intel is registered trademarks of Intel Corporation MS DOS Microsoft C and Quick BASIC are trademarks of Microsoft Corporation VIA is a trademark of VIA Technologies Inc SST is a trademark of Silicon Storage Technology Inc UMC is a trademark of United Microelectronics Corporation Other brand names and trademarks are the properties and registered brands of their respective owners Table of Contents T SAT JADDIOVAIS Salety CHAPTER 1 INTRODUCTION ee 1 1 General Description 1 2 Package LIS oto dresse RH oic 1 3 606 1 4 DIMENSIONS ile ki 1 5 VO CHAPTER 2 SYSTEM SETUP 2 1 System Configuration 2 2 OSE Se WING courbe 2 3 Mount 23 istumassa tata maana dada 2 32 es detto baeo 2 9 9 Desktop Stand samaiset CHAPTER 3 DRIVERS INSTALLATION 3 1 SYSE M eaa 3 2 TOUC SEES EM asetades 92 1 3 2 2 Driver Installation Windows 3 3 Bluetooth optional Vi Vii MEMO MMT225 User s Manual CHAPTER 1 INTRODUCTION chapter contains the general information and detailed This specifications
4. IK AXIOMTEK MMT225 22 TFT Medical Grade LCD Monitor User s Manual Disclaimers This manual has been carefully checked and believed to contain accurate information AXIOMTEK Co Ltd assumes no responsibility for any infringements of patents or any third party s rights and any liability arising from such use AXIOMTEK does not warrant or assume any legal liability or responsibility for the accuracy completeness or usefulness of any information in this document AXIOMTEK does not make any commitment to update the information in this manual AXIOMTEK reserves the right to change or revise this document and or product at any time without notice No part of this document may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of AXIOMTEK Co Ltd Copyright 2009 AXIOMTEK Co Ltd All Rights Reserved December 2009 Version A1 Printed in Taiwan Safety Approvals Marking UL60601 1 EN60601 1 FCC Class B FCC Compliance This equipment has been tested in compliance with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are meant to provide reasonable protection against harmful interference in a residential installation If not installed and used in accordance with proper instructions this equipment might generate or radi
5. R 2 SYSTEM SETUP This chapter details the system parts and components with figures It includes m System Configuration m OSD Setting m Wall Mount VESA Desktop Stand methods 2 1 System Configuration The MMT225 provides display control on screen display The descriptions of the functions are listed below 1 Monitor switch Press this button to turn on off the monitor 2 Power LED When the light is green the power is on flash when the power is turn off 3 SEL To increase the value of selected item 4 SEL To decrease the value of selected item 8 System Setup MMT225 User s Manual 5 Menu Press this button to turn on off the OSD On Screen Display 6 Auto Adjusted Return This button is auto image adjustment and return System Setup 9 MMT225 User s Manual 2 2 OSD Setting The MMT225 provides OSD On Screen Display to adjust brightness contrast clock et al Please follow the steps are listed as below 1 Please press the Menu button on the OSD keypad You could see General menu If you want to adjust sub item you could press the Menu button on the OSD keypad 2 Please press the SEL button on the OSD keypad You will entry Audio menu You could adjust volume or mute 10 System Setup MMT225 User s Manual 3 Please press the SEL button on the OSD keypad You will entry Color menu If you want to adjust sub item you could pre
6. al that customer can install as below Step 1 Prepare the parts of desktop stand Screw A Screw B Screw C System Setup 15 MMT225 User s Manual Step 2 Assemble the desktop stand Fix the screws as marked on the bottom side of chassis Use Screw A Step 3 Fix the screws as marked on the back side of chassis Use Screw B 16 System Setup MMT225 User s Manual Step 4 Assembly the hinge cover and fix the screws as marked on the back side of chassis Use Screw C System Setup 17 MMT225 User s Manual Step 5 Finish 18 System Setup MMT225 User s Manual MEMO System Setup 19 MMT225 User s Manual CHAPTER 3 DRIVERS INSTALLATION 3 1 System MMT225 supports Windows XP To facilitate the installation of system driver please carefully read the instructions in this chapter before start installing The installation method of the touch and Bluetooth optional are listed below 3 2 Touch Screen The MMT225 uses the 5 wire analog resistive There are the specification and driver installation which are listed below 3 2 1 Specification 5 wire Analog Resistive type Touch Screen Controller PenMount 6000 USB Touch Screen Controller IC USB interface 1024 x 1024 10 bit A D converter inside Power Input celo Active 24 6 Idle Mode 13 4mA 20 Drivers Installation MMT225 User s Manual 3 2 2 Driver Installation Windows XP The MMT225 provid
7. ate radio frequency energy and cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user 15 encouraged to try to correct the interference by one or more of the following methods Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment to another outlet of a circuit that doesn t connect with the receiver 4 Consult the dealer or an experienced radio TV technician for help Shielded interface cables must be used in order to comply with the emission limits Safety Precautions Before getting started please read the following important safety precautions The MMT225 does not come equipped with an operating system An operating system must be loaded first before installing any software into the computer Be sure to ground yourself to prevent static charge when installing the internal components Use a grounding wrist strap and place all electronic components in any static shielded devices Most electronic components are sensitive to static electrical charge Disconnect the power cord from the MMT225 before any installation Be sure both the system and external devices are turned OFF A sudden surge of power could ruin
8. e MMT225 the bundled package should contain the following items MMT225 1 Driver CD x1 Medical Power Adapter x1 USB cable x 1 Audio cable x 2 VGA cable x 1 Wall mount kit Desktop Stand Kit optional VESA ARM optional you can not find the package or any items are missing please contact AXIOMTEK distributors immediately Introduction 3 MMT225 User s Manual 1 3 Specifications Display 22 LCD Max Resolution 1680 x1050 Brightness 300nits Max Colors 16 7M View Angle H 178 V 178 Front Bezel Plastic ABC Control OSD On Screen Display control pad on front side IO outlets 1 x Audio 1 x VGA 1 x DVI 1 x USB Slave for DSC T S Vv VVV v v 2 x USB Host 1 Composite 1 x S Video Mounting Support Wall mount and VESA FPMPMI mounting Operating Temperature Range 0C 45 C Relative Humidity 20 90 non condensing Vibration 5 to 500 Hz 2 0 G random Introduction gt MMT225 User s Manual 1 4 Dimensions This diagram shows you dimensions and outlines of the MMT225 0000009 s 7 2 N Introduction MMT225 User s Manual 1 5 I O Outlets Please refer to the following illustration for I O locations of the MMT225 6 Introduction MMT225 User s Manual s Introduction MMT225 User s Manual CHAPTE
9. es a touch screen driver that users can install it under the operating system Windows XP To facilitate installation of the touch screen driver you should read the instructions in this chapter carefully before you attempt installation 1 Insert Driver CD and follow the path to select the Drivers XP Step 1 Touch gt Step 1 Touch 2 Double chick the icon Setup Driver 3 Follow the installing procedure and press OK Drivers Installation 21 MMT225 User s Manual 4 Click Start menu and select PenMount Utilities and then PenMount Control Panel pops out PenMount Control Panel Device Multiple Monitors Tools X About bi Penmount Control Panel version 93 Installed Device s Device 0 6000 U56 Support E mail penmointiseed net tw Support Website http penmount cam b 5 Select the Standard Calibrate tab Device 0 PenMount 6000 USB Calibrate Setting Edge Compensation About Advanced Plat calibration data Standard Calibration Advanced Calibration Turn off EEPROM storage 6 Calibration 22 Drivers Installation MMT225 User s Manual To adjust the display with touch panel click Calibration and follow the calibrate point to do calibration there are five points on screen for calibration Fri Ey Touch the red square 7 Press Drivers Installation 23
10. of the MMT225 Chapter 1 includes the following sections General Description Specification Dimensions I O Outlets Package List General Description MMT225 is a Medical Grade LCD Monitor It adopts 22 300nits 1 1 The WSXGA LCD display and numerous signal interfaces including DVI VGA S Video Composite Audio in and 3 USB 1 slave 2 hosts There is an OSD function making you ease adjustment on screen image The MMT225 has more comfort safety and environmental protection for humanized amp health consideration those would be the benefit that users can get Medical grade Product Design The features of the MMT series are low noise operation low power consumption and high reliability And the MMT225 conforms UL60601 1 EN60601 1 and FCC class B Thus it is best suited for medical environment applications gt Introduction 1 MMT225 User s Manual gt Spill and dust resistant The MMT225 has water proof design of the IP65 front panel and IPx1 whole enclosure so the entire system is protected from water drip damages gt Multi Display Mode supports Support VGA 640 x 480 SVGA 800 x 600 XGA 1024 x 768 SXGA 1280 x 1024 and WSXGA 1680 x1050 gt Multi signal inputs Support VGA S video Composite DVI Audio in 3 USB ports 2 x type A 1 x type B so the MMT225 can receives TV and PC signals 2 Introduction MMT225 User s Manual 1 2 Package List When you receive th
11. ss the Menu button on the OSD keypad Red Green 1 4 Please press the SEL button on the OSD keypad You will entry Languages menu MMT225 support 8 languages English French German Spanish Italian Japanese Russian and Chinese mh EELA CD Tf ene T System Setup 11 MMT225 User s Manual 5 Please press the SEL button on the OSD keypad You will entry Tools menu If you want to adjust sub item you could press the Menu button on the OSD keypad me Out Position 6 Please press the SEL button on the OSD keypad You will entry Exit menu If you want to leave the OSD you would press menu Digital V H 5 S Video NT665 22W 091125V1 1 12 System Setup MMT225 User s Manual 2 3 Mount Methods There are several mounting ways for the MMT225 Wall VESA and Desktop mountings 2 3 1 Wall Mount The MMT225 provides wall mount kit Please follow the steps as below Prepare all parts for installing the wall mount kit A STS mire 4 Dirt Step 2 Assemble the wall mount kit by using screws to fix the back System Setup 13 MMT225 User s Manual 2 3 2 VESA mount The MMT225 provides two types of VESA mount 75mm x 75mm and 100mm x 100mm 14 System Setup MMT225 User s Manual 2 3 3 Desktop Stand The MMT225 provides desktop stand option
Download Pdf Manuals
Related Search