Manual - EUSSO Technologies, Inc.
Contents
1. VDSL2 Converter User s Manual FCC Certifications FC This Equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CEN Wain CE This equipment complies with the requirements relating to electromagnetic compatibility EN 55022 Class A for ITE the essential protection requirement of Council Directive 89 336 EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility Company has an on going policy of upgrading its products and it may be possible that information in this document is not up to date Please check with your local distributors for th2. SL2 Converter The converter does not require any software configuration Users can immediately use any feature of this product simply by attaching the cables and plug power on There is some key limitation on the Ethernet over VDSL2 networking please check the following items e The device is used for point to point connection only and allows data and voice work on the same telephone lines e The two RJ 11 connectors one for voice device connection like telephone and the other one for network line connection This device is an ideal client access unit for the applications of apartment hotel campus and hospitality Integration with the Internet access Concentrator the total infrastructure could be a perfect solution for multi media local Internet This structure could support many multi media applications like VOD Video on Demand Distant education Internet caching server and so on Therefore most of the traffic will be limited on the local phone line network instead of flooding to the Internet Another application for the converter is used for LAN to LAN extension through the normal telephone line Connect to I nternet Access Concentrator In order to build up a local Internet in apartment hotel campus and hospitality environment the Internet Access Concentrators need to be placed in the wiring center MDF room and connect to the telephone line system On the other hand you need to install a converter on the indi
3. e latest information No part of this document can be copied or reproduced in any form without written consent from the company Trademarks All trade names and trademarks are the properties of their respective companies Copyright 2007 All Rights Reserved Unpacking I nformation Thank you for purchasing the Ethernet over VDSL2 converter Before installation please check that your package contains the following items i One Ethernet over VDSL2 converter 2 One power adapter 3 One telephone line 4 One user s manual Introduction General Description The VDSL2 supports the signal conversion between traditional Ethernet and innovative VDSL2 technology The device is a right solution to integrate current Ethernet application with the new building phone line networking technology like hotel office and apartment environment The EoVDSL2 port supports symmetry and asymmetry data transmission bandwidth up to 50Mbps and transmission distance up to 1000ft It is ideal for providing video on demand and multi media service to apartment hotel and campus without rewiring cable consideration Moreover the distance expansion also provides wide range coverage The converter is plug n play without any software to configure and also fully compliant with all kinds of network protocols Moreover the rich diagnostic LEDs on the front panel provide the operating status of the system The cable specifications of the conn
4. ection are listed as following 10BASE T Category 3 4 or 5 UTP STP 100BASE TX Category 5 UTP STP Ethernet over VDSL2 Twisted pair telephone wires The drawing listed below is typical application for the Ethernet over VDSL2 converter Master Phoreline Slave Key Features e Complies with I EEE802 3 10BASE T standard e Complies with EEE802 3u 100BASE TX standard e Compliance with VDSL2 ITU T G 993 2 e Supports 1 RJ 11 port for Ethernet over VDSL2 e Provides 1 RJ 11 port for telephone connection e Provides 2 RJ 45 ports for 10 100Mbps Ethernet e Provides 1 Dip Switch for mode selection e Voice and Data work on the same telephone line e EoVDSL2 port supports maximum bandwidth 100Mbps 50Mbps downstream upstream over 1000ft 300m e Long Reach VDSL2 performance around 7Mbps downstream over 5000ft 1500m e Mini size design 120 x 75 x 25mm Provides rich diagnostic LED indicators e External Power Adapter The Front Panel cm nee vo See ewe ow nit sane VOSU2 Converter The Rear Panel Demet na sco heme t rome wos Dip Switch Settings Pin1 Pin2 Pin3 Pin4 Side Mode Rate limit SNR ON Slave CPE Fast No limit 6dB OFF Master CO Interleave 50 20 Mbps 9dB Pin1 Master slave switch Master CO EoVDSL2 converter acts as Master Central Office CO side Slave CPE EoVDSL2 converter acts as S
5. lave Customer Premise Equipment CPE side Pin2 Impulse noise protection Fast mode Direct data transmission with latency less than 1 ms Interleave mode Provides communication protection for up to 250ms impulse noise with latency less than 6 ms Pin3 Rate limit control No limit Provides up to 100Mbps 50Mbps line rate in short line 50 20 Mbps Line rate limited to 50 20Mbps Pin4 General protection 6dB Original channel noise protection with 6 dB SNR QdB Better channel noise protection with SNR up to 9 dB Note SNR Signal Noise Rate Signal Noise Switch on this pin depends on your network demand LEDs Definition LED Status Operation Power Green The device is powered on Off The device is powered off Green The port is connected VDSL Blinking Green Data transceiving Off No valid link on this port Green The port is connected 10 100M Blinking Green Data transceiving Green The device acts as Master mode Mester Off The master mode is off Green The device acts as Slave mode Slave The slave mode is off Once the converter connects to a power source the LEDs of 10 100M will blink once and the converter begins looking for other converter automatically During searching the VDSL LEDs keeps blinking it will stop blinking after success detection Installing and Using VDSL2 Converter Installing the Ethernet over VD
6. nnector for telephone connection 1 DIP switch for selective transmission modes Interface LED Power 1 VDSL 1 LAN 2 indications Master mode 1 Slave mode 1 Emission FCC Class A CE VCCI Class A Operating Operating 0 40 C 32 104 F Temperature Storage 10 70 C Operating 10 90 non condensing Storage 5 95 Operating Humidity 61NB VE6840 204
7. vidual client side and connect to the Concentrator through the telephone lines When deciding where to put the converter then you must ensure e It is accessible and cables can be connected easily Cabling is away from sources of electrical noise such as radios transmitters and power lines and fluorescent lighting fixtures e Water or moisture cannot enter the unit e Airflow around the unit and through the vents in the side of the case is not restricted company recommend that you provide a minimum of 25mm clearance To prolong the operational life of your units e Do not place objects on top of any unit or stack e Do not obstruct any vents at the sides of the case Installing Network Cables After placing the converter on the desktop then we need to know how to connect the device to network Station Connections with Telephone Wires Connect the network adapters in stations to the converter s RJ 45 port through category 3 4 or 5 UTP STP cables There are two RJ 11 phone jacks one for telephone set connection and the other one is used for phone line network connection If you have telephone wall jacks at home then all you need to do is connecting the RJ 11 network port to the wall jack through telephone wires Product Specifications IEEE802 3 standard IEEE802 3u standard Ethernet over VDSL2 VDSL2 ITU T G 993 2 Standard 2 RJ 45 10 100Mbps Ethernet ports 1 RJ 11 connector for EoVDSL2 1 RJ 11 co
Download Pdf Manuals
Related Search