ONE TECHNOLOGIES MIGHTY BOX User Manual Firmware
Contents
1. Notice the drive shown as hda is the one in the upper slot of the MIGHTY BOX while hdd is the disk located in the lowest slot of the system To setup a disk as single drive chose a filesystem ext2 ext3 FAT32 or NTFS from the dropdown menu and click on Format After formatting is finished the volume will automatically be mounted Repeat this procedure to configure more disks NOTICE If you want to use the encryption function you have to chose ext2 as filesystem It is the only one supporting data encryption If you plan to use the user quota management you have to select ext2 or ext3 as file system NTFS or FAT32 do not support the quota function Mighty Box Manual S is ONE ONE Technologies FAT32 is not recommended for formating large hard disks like the internal disks used inside the Mighty Box This option is intendet to be used for USB Flash devices located at the backside of the Mighty Box like USB Pendrives etc You can use NTFS if you do not want to make use of the encrytion or the quota management and if you prefer to have a file system more compatible to Microsoft Windows based computers Below the table of disks you will find the spindown function settings According to your browser size or display resolution you might have to scroll down to see it Disk Utility Device Name Type Mount Point Status EneYPtEPassword F ormat een Karen ES Type Form2. guest share END LIST Step 2 3 User Management In this step the new user testuser can be assigned to a user groups In the right windows all available user groups will be shown As long as no own user groups are created only the default guest share group will be displayed here Once you have created own user groups you can select them and add the user by clicking Add All groups the user belongs to will be shown in the left window To remove the user from a group select it from the left window and click on Remove to remove the user from the group Mighty Box Manual sdg ONE ONE Technologies Click on next when finished Step 3 3 Share Permission Step 3 3 Share Permission testuser Access Granted Access Denied md share folder public END LIST z lt Read Only END LIST lt lt Writable In the last step you can configure for which share the user shall have access and in which way he will have access to it To do so select a share from the right window and click on READ ONLY if the user shall have the possibility to access the shared folder without the permission to write into it WRITABLE if you want to grant full access to this folder share Repeat this until all shares the user shall be able to use are listed in the left window All remaining shares in the right window will not be accessible by this user
3. User Groups To create a new user group select Add Group from the Quick Setup menu Step 1 3 em Add Group O J Group Name testgroup Wizard Add User Add Group Add Share ONE TECHNOLOGIES www one lechnhologies com Quick Setup Enter a name for the new user group in the first step and click on Next Mighty Box Manual 20 ONE ONE Technologies step 2 3 Group Member testgroup Member Non member END LIST admin guest share END LIST Remove gt gt In the second step you can specify which users shall be included in the new group Select the users you want to include from the right window and click on Add to add the user to the member list To remove a user from the member list select the user from the left window and click on Remove Click on Next when finished Step 3 3 ohare Permission testgroup Access Granted Access Denied END LIST lt lt Read Only md share folder public END LIST In the third step it is possible to grant access to a folder share to the whole group Doing so results in all group members inheriting these permissions accordingly Click on Confirm to save and create the settings for this user group Shares Step 1 3 l ee e Add share ONE TECHNOLOGIES O E www one lochnologies cam Share Name testshare Quick Setup Path mnt idel sys W
4. After the configuration of the RAID set has been finished successfully the RAID menu screen will appear showing information about the new RAID set on top of the screen You can see the RAID level the file system and the size of the RAID There is also information about the already used capacity system files at this time Instead of the selection buttons for RAID level and file system two new buttons will be shown REMOVE RAID and EXCHANGE DISK REMOVE RAID press this button to remove the RAID This will erase all data stored on the RAID and the disks will become available for another configuration again EXCHANGE DISK In case a disk fails during operation in a RAID 5 you can select the defective disk by ticking its checkbox and click on Exchange Disk afterwards Doing so allows you to exchange the defective disks by a new one which will be integrated into the RAID 5 as replacement disk The rebuild process will automatically start and will restore the data lost with the defective disk After rebuild has been successfully ended all data will be available as it was before the previous disk failed Rebuilding the data can take several hours depending on the amount of data which has to be rebuilt Mighty Box Manual alze ONE ONE Technologies Disk Utility Enc rypt Password Format Device Name Type Mount Point Status Scandisk Umount Health TotalSize RE encrypt raid ni EI 900
5. Click on save after you changed any settings to make them permanent Mighty Box Manual 24 ONE ONE Technologies File and Print File Server Setting Character set Latin 1 Western European CP1252 EE ON i ER Windows Setting Users and Groups Enable E File and Print l Workgroup WORKGROUP File Server Share Management Description MIGHTYBOX Printer Server AjaXplorer WINS Server Optional System A Network Service FIF Server Setting Maintenance Enable EI Log File Enable FTP with TLS a Port Number 21 NFS Server Setting Enable Guest Access Setting Enable Enable Quota Guest user Quota MB Save File Server Menu Select the File Server menu to configure the settings for providing files in your network Character set Choose the correct character set for your location from the drop down list Windows Setting Enable Activate this checkbox to make the Mighty Box available in windows networks Workgroup Enter the name of your windows workgroup in which the Mighty Box shall be included Description Name of the Mighty Box which will be seen in the windows network WINS Server If it is necessary to specify a WINS server in your network you can enter its IP number here FTP Server Setting Enable Activate this checkbox to make the Mighty Box available as FTP Server Enable FTP with TLS Activate this checkbox if you want to use TLS encryption for FTP transfers Port Number Ent
6. Both information will then be obtained from your DHCP server and will be used by the Mighty Box accordingly If you do not use a DHCP server or want to configure the Mighty Box manually with an IP address besides the DHCP range set the option to Use following IP Address and Use following DNS Server Address Enter the IP numbers in the appropriate fields and click on save to confirm your entries MAC Address Shows the MAC address of your Mighty Box Mighty Box Manual 27 ONE ONE Technologies Wireless Settings Wireless Settings Wireless Enabled E O E AP STA mode AP Mode ONE TECHNOLOGIES www one lechnoloegies cam SAD MIGHTYBOX Users and Groups File and Print Hide SSID E System Y LAN Settings Country Region ETS Europe Korea Australia Wireless Settings Channel E Time Settings Information Wireless Mode 802 11B G mixed default Disk Usage Maintenance Authentication Mode OPEN b Log File Encryption Type NONE Save Select the Wireless Settings menu to configure the WLAN function of the Mighty Box Wireless Enabled If you want to use the WLAN function of the Mighty Box activate the Wireless Enabled checkbox AP STA mode Select the WLAN mode you want to use Choose AP Mode if the Mighty Box shall behave as an access point This means that client computers or other WLAN enabled devices can connect to the Mighty Box d
7. Transmit Rate According to the selected wireless standard the Mighty Box supports all transmission rates covered by these two standards If a client device is limited to a lower speed rate the Mighty Box will automatically adjust the used transmission speed accordingly You have the possibility to fix this soeed rate to a Mighty Box Manual 28 ONE ONE Technologies fixed value if you detect problems with older client devices Keep in mind that changing the rate to a fixed value will cause the Mighty Box only to use this rate for all devices Authentication Mode The Mighty Box supports different authentication modes for a secure authentication between Mighty Box and client device Select the mode you want to use and pay attention to the modes available on your client devices Encryption Type According to the authentication mode selected in the previous setting the possible choices will change By default the authentication mode is set to OPEN and encryption is set to NONE This can be used to test the basic function after enabling the WLAN function It is NOT RECOMMENDED to be kept afterwards since this will enable every device to communicate with your Mighty Box without the need of any keywords or password phrases After the initial test please change the authentication type immediately and use safe passwords for encryption Click on save to confirm your settings and activate or deactivate the WLAN function NOT
8. Setup menus wizard you will not get a step by step wizard but all settings on one page This is comfortable for users already knowing how to setup new users User Management admin ONE TECHHOLOGIES mete hora www_one loachnologios cam O E guest share Existing Users aa Users and Groups User Management Group Management File and Print system User Name Network Service S Maintenance RE L Log File Please type your password again Description optional C Create Shared private Folder Shared Private Folder Location mntidel sys Enable Quota of MB Only for system hard disk and ext2 ext3 file system Groups Delete User The list on top of the screen shows the already existing users Select one of them to see its settings and or change them e g new password etc To add a new user select ADD USER from the existing users list Fill the blank fields with the information of the new user like user name and password Enable Create Shared private Folder if the new user shall get its own private folder and select the volume where it shall be stored As indicated the quota function for the private folder is only available if the folder path is on the system volume and the file system is ext2 or ext3 Click on save if all information is correct and the user shall be created To delete a user from the system simply select the user from the list and click on the Delete U
9. apply them by clicking on Confirm If you find any errors you want to correct you can use the Back button to go back to the previous menu pages again If you want to leave the Quick Setup Wizard without making any changes to the system you can click on Cancel to discard all changes and keep to the current settings This option is available on all wizard pages The basic configuration is now done Before head on creating new users by using the next wizard from the setup menu it is recommended to check the hard drive configuration first and if necessary to change it according to your needs Reason for this recommendation Changing the configuration of the hard drives inside the Mighty Box might result in a loss of all recent configurations This will happen if the changes include the system disk For example changing the hard drive configuration from JBOD mode to RAID Level 5 including all available hard disks will delete the existing configurations To check and if necessary change the disk configuration click on the yellow Administration menu button located at the lower border of the browser frame Administration Doing so brings up the sub categories of the administration menu on the left side of the window Mighty Box Manual ONE Technologies System Information Product Name MIGHT YBOX Ge O E Firmware Version 20100615 1734 OneTechnologies 4bay_rt2561 Product Vendor ONE Technologies L
10. been finalized and the device is ready If your local area network LAN provides a DHCP server the Mighty Box is using it to receive an IP number to work with by default If DHCP service is not present in your LAN the device will use its predefined IP number 192 168 1 100 To start with the configuration of the device start a web browser on a computer located at the same network as the Mighty Box itself Enter the shown IP number in your browsers address field Example http 192 168 xxx xxx The Mighty Box will answer by presenting its login screen in your browser ONE TECHNOLOGIES wewione lechnologies cam Username admin Password seese For username as well as password enter admin This is the preconfigured administrator account which can be used for the first login and configuration You should change the administrator password into a secure and secret password after finishing the first setup After a successful login to the System you ll see the system information Mighty Box Manual 4 ONE ONE Technologies System Information Produktname MIGHTYBOX e E O E Firmware Version 20100615 1734_OneTechnologies_4Abay_rt2561 Produkt Hersteller ONE Technologies Quick Setup IPAdresse 192 168 214 181 MAC Adresse 00 14 D7 05 01 14 RAID 108MB 1430804MB HDD3 128MB 234729MB HDD1 264MB 468440MB 06090929Q The information page shows a quick summary of the basic hardware configuration of the Mighty Box It shows the i
11. by using the drop down lists of each component NOTICE If you select time and date manually these settings will be lost when powering off the Mighty Box This will happen because the device has no buffer batteries for keeping this information during power off mode Opposite all other information which is static data date and time are not static and therefore cannot be Mighty Box Manual gf ONE ONE Technologies stored on the systems hard drive After starting up the device again you will have to reenter date and time Using a time server allows the Mighty Box to update date and time every time it is starting up automatically 6 Step Summary ONE TECHNOLOGIES ONE www one technologies com Quick Setup Wizard Add User Add Group Add Share Step 6 6 Wizard Setting Confirmation Current Settings Uu Language English Hostname MIGHT YBOX Automatic Obtain IP Address IP Address Subnet Mask Default Gateway Automatic Obtain DNS Server ae Secondary Others Date and Time 1 1 2010 5 41 AM Time Zone Greenwich NTP Server time_nist gov New Settings English MIGHTYBOX Automatic Obtain IP Address Subnet Mask Default Gateway Automatic Obtain Primary Secondary Others 1 1 2010 5 41 AM Greenwich time nist gov EES SN KE In the sixth and last step you see an overview and a comparison of the old current and new settings You should now have a final check on your new settings and if they all are correct you can
12. clicking on Clean below each table Log files allow e g to check user activities like access time and downloaded files by FTP etc 2010 ONE Technologies GmbH Germany Mighty Box Manual 36 ONE
13. it becomes available in the destination device list Select the correct drive from the destination list and click on Backup Now to perform a backup immediately If you prefer to have a scheduled backup choose the schedule time and click on Schedule to activate the scheduled backup plan Mighty Box Manual 30 ONE ONE Technologies NETWORK SERVICE DHCP Server Settings DHCP Server Setting Enable Server ET ONE TECHNOLOGIES 2 Se www one fachnologies cam O E DHCP Client Slide subnet Mask optional Users and Groups l File and Print Default Gateway optional System Network Service DHCP Server Secondary DNS optional Bonjour Blorrent Others DNS optional Media Server Primary DNS optional rece DHCP IP Address Start 192 168 1 2 M aintenance Log File DHCF IP Address End 192 168 1 50 Maximum Lease Time 1 Day M Save DHCF lease list Static IP The Mighty Box can be configured as DHCP server too If you do not have another DHCP server in your network and want to use the ease of network IP management by DHCP or you may want to setup a separate network click the enable server checkbox Attention If you want to use the Mighty Box as DHCP server the system must be configured with a fixed IP number before this function can be activated Enter all network data in the following fields All entered data will be provided to the client devices after establishing a connection to yo
14. restrictions public folder Step 3 3 NES Access testshare Grant access to all Allowable IP Subnet o IP Address END LIST Add Subnet The next step shows the menu to define the NFS access in your network If you use NFS as access protocol you can define which IP number or network range shall be allowed to access the share To add single addresses select the IP Address option and enter the IP number of the client Click on add to add the entered number to the Allowed IP Subnet list To include a subnet to the list select the Subnet option and enter the start and end IP number in the fields Click on Add to include it to the list To remove a single IP or an IP range select it from the left window and click on remove If you do not want to restrict NFS access activate Grant access to all to allow every client to access the share by NFS Click on Confirm to save your settings and create the new share Mighty Box Manual 22 ONE ONE Technologies Administration Menu To access the Administration Menu click on the yellow button The submenus of the administration menu will appear on the left side of the window Each of the listed submenus will offer its own submenus after selecting it from the list User and Groups Click on User and Groups to see the two submenus User Management and Group Management Other than in the
15. ways to do so 1 Create each user manually by using the administration menu s Chapter Administration menu 2 Use the Create User Wizard from the setup menu for a step by step guided setup which will be explained here Select the Setup menu by clicking the green button at the bottom of the window and chose Quick Setup and Add User Mighty Box Manual 18 ONE ONE Technologies Step 1 3 Add User User Name testuser Password Seen es Please type your password again EE testuser for demonstration Fl Create Shared private Folder Shared Private Folder Location mnt idel sys There are three steps to go through to create a new user Step 1 3 Add User Enter a name for the new user in the User Name field Enter a password for this user in the Password field and repeat it in the next field to avoid mistyping If you want to you can enter a description as reminder or information optional If this user shall get an own private folder you can select this option here and define the volume where the folder shall be located by selecting one from the list If this user shall have a limited capacity for his private folder you can activate the quota function here and enter the maximum capacity he is allowed to use in Megabytes Note Quota function is only available if the file system is ext2 or ext3 Step 2 3 User Management testuser Member Non member END LIST
16. D Just a Bunch Of Disks RAID Redundant Array of Independent Disks To see which kind of RAID has been configured you have to change to the RAID Setting menu The Mighty Box can be configured in different ways JBOD each hard drive will appear as single individual volume RAID some or all hard drives will be combined into a RAID The RAID appears as one volume As a new function in the June 2010 firmware version also combinations of both JBOD amp RAID are possible in the following combinations 2 HDs in RAID 1 or RAID O and 2 HDs as single volume in JBOD 3 HDs in RAID 5 or RAID O and 1 HD as single volume in JBOD A combination of two RAIDs e g 2x RAID 1 is not possible Explanation of the RAID Levels JBOD Each drive will show up as individual volume no RAID LINEAR All disks setup as LINEAR volume will be combined as total capacity and will be shown as one large volume In this case it does not matter if they have the same size or not since all of them are used as single drives That means All data stored to a LINEAR volume will be stored on the first disk unless there is no capacity left Then the second disk will be used etc None of the data will be split between the drives The advantage is to combine some smaller drives to one large volume without losing capacity There is no increase of speed or any data security RAID 0 All data will be split to all disks That means that all data is partially s
17. ICE Changing the settings from enabled to disabled or vice versa forces the Mighty Box to reboot to activate the new WLAN status Also the MAC address will change between WLAN adapter MAC address and LAN adapter MAC address If you use a DHCP server it may detect the Mighty Box as a new device because of the new MAC address and assigns a new IP number to it If your browser will not return to the login screen automatically please check the IP number shown on the Mighty Box front panel display and use this number to access the Mighty Box again Time Settings Time Settings Date Month 5 Day Year 2010 ONE TECHNOLOGIES E www one lachnologies com O Time Hour q Minute 5J DM l T Se E Time Zone GMT 01 00 Amsterdam Berlin Bern Rome Vienna M Users and Groups File and Print NTP Server Default time nistgov e System _ LAN Settings User Define Wireless Settings C Enable DST Daylight Saving Time Time Settings Information ES Disk Usage Network Service Maintenance Log File This menu allows to configure the time and date used by the Mighty Box for log file entries and also for data information Select the time zone of your location from the drop down menu and your preferred time server under NTP Server You can use one of the predefined time servers from the list or click on User Define and enter a server of your choice Save your settings and click on Update Time to receive the actual date and time If y
18. OLOGIES wW one technologies com Please select statistics information Summary e ees pr Disk Name Capacity Used Free Disk Usage oi SES and oups 7 ES SS EE idevimd 953874MB 93MB 953781MB 0 System Idevisdb USB2 1909MB 1030MB 879MB 53 SI Ss SE dev sda USB1 OMB REE Bs Slt idevinda 475909MB 425MB 475484MB 0 Time Settings Information Refresh Disk Usage Network Service Maintenance Backup Source public og File Destination USB2 Backup Now Schedule none e DAM e OAM e schedule In this menu you can check the recent status of disk usage The table shows information about every volume available in the system By default the menu opens with the summary table If you want to see how many data is stored by each user you can change the view by selecting Users from the pull down list on top of the table The information will change to user based disk usage If quota function has been activated the percentage of quota usage will be available too Since the content of the public folder is subjected to change very often because it is the most used folder the Mighty Box offers the possibility to backup the data stored inside the public folder to an external storage device To use this function a formatted USB storage device external hard disk or USB pen drive etc has to be connected to one of the USB ports at the rear side of the Mighty Box As soon as it has been detected by the system
19. ONE Technologies ONE TECHNOLOGIES MIGHTY BOX User Manual Firmware Version 201005xx and later Content PCC e A EE 3 BEEN ge hi cel goes a e KE 3 OS E TE 3 Tiken E en WEE 4 Mond BOTTONE erran E E A 5 Quick setup by using the SETUP MENU esssssssssssssrssersnssrnnerensrrresernnsrersstrnseresrtessresrtrertreseresrteserereeereene 6 1 Step Language Setting 6 2 Step Password Setting 7 3 Step EE 7 A Step Internet Protocol Settingei 8 5 Step Time Eegeregie 8 GI Step umman 9 CONMEUration e WEIEN 12 Setting up a RAID in the RAID Setting menu 14 Users Groups and ENEE 18 sen oe 2 0 U EE 19 Step Fo U er Manat ement E 19 Step y3 Share gn EE 20 BE GROWS EE 20 DA e 21 Administration VICI EE 23 BEE Gi ee AEE E AEE EE ener EAE ene a ee A EEA E ee A A eee 23 GOUD eae 24 SISCH Le RG II E 25 Mighty Box Manual sde ONE ONE Technologies FS SCP E E 25 Share Ee EE EN 26 Printer EEGENEN 26 ER dee 27 SEENEN 27 BOCK gel 27 MMS SSS ea cctes castorate ant ects chiectss E toes tedan os dun basen tcnoe deve stones aactarakGdanneretornntccecterse 28 FMVS SO INDE asvrctananrcetoresskcacecenctreedaqhsancduaadarauncdmedcntdenedentenrcuna EE 29 ARO AUN DEE 30 BI 30 NETWORK SERVICE E 31 Melen EN FO OU SE UNE esceisenr nie anon eutdon sate ta nesiceeuaucat N A 32 BEO i E 33 Media SO E 34 MAINTENANCE MENU EE 34 EEDA I E e EN 34 Ba CONE O aa rasan aaaneccneitasogaaneseaessecteoenenstoaenwcseasesaeacccsese
20. Setting Firmware Upgrade SAVE CONFIGUEALON Factory Reset Log File To restore a previously saved configuration click on brows to locate the configuration file on your local computer and select it Click on Restore to start the restoring process Factory Reset ONE TECHNOLOGIES www one lechnologies Com Users and Groups O E Caution You will lose all user data Factory Reset To restore the factory default settings click the Factory Reset button File and Print System Network Service Maintenance Disk Utility RAID Setting Firmware Upgrade Save Configuration Restore Configuration Tactory Reset Log File If you want to restore the default factory values and settings of the Mighty Box click on the Factory Reset button Doing so will restore all settings to the factory default values Mighty Box Manual 35 ONE ONE Technologies Log File Samba Log User From Time Information 2010 08 08 22 22 28 0 smbd version 3 0 25a started Ga ONE TECHNOLOGIES www one technologies com Users and Groups File and Print System Network Service Maintenance Log File FTP Log DHCP Server Log System Log Administration Log The system writes several information into log files These log files can be displayed here Select the log file you want to see from the menu and the information will be displayed in a table You can clean the listing by
21. Xplorer ONE TECHNOLOGIES O E Please install the AjaXplorer software into public and Aa ie ee reboot the system Users and Groups File and Print File Server Share Management Printer Server AjaXplorer System Network Service Maintenance Log File This menu will become active after the AjaXplorer software has been installed on the Mighty Box The AjaXplorer allows cloud access to your Mighty Box by simply using a web browser This feature is supplied as additional add on Please refer to the separate instructions provided with the add ons SYSTEM LAN Settings LAN Settings Hostname MIGHTYBOX ONE TECHHOLOGIES O E k A EE cat wm P Address Setting 5 Obtain IP Address automatically Te e Use following IP Address sers and Groups l Fie and Print IP Address 192 166 2 1 10 System Subnet Mask 255 6255 8255 80 __LAN Settings Default Gateway 132 Be Bu it Wireless Settings ES ee EET Time Settings Obtain DNS Server Address automatically Information e Use following DNS Server Address ge Disk Usage Pane Network Service Maintenance F Secondary Log File Others MAC Address Save Enter the LAN Settings menu to configure your Mighty Box network settings Hostname Enter the name the Mighty Box will use to show up in your network environment IP Address Setting If you use a DHCP server in your network you can select Obtain IP Address automatically and also Obtain DNS Server Address automatically
22. at Scandisk Umount TotalSize Jencrypt idewhdd ntfs mntide4 mounted ext scan Umount PASSED ME i GBytes idewhde nifs mntides3 mounted 500 GBytes scan Umount PASSED My v00 idew hdb s mntide2 mounted sc mount les encrypt dev hda mntidet mounted z i EUS GBytes ormat Refresh It is possible to spin down hard disks after a special period of time without usage You can enter this period in minutes here and click save to activate it NOTICE This function only affects non system disks If you configure your Mighty Box as JBOD NAS with all disks used separately only three disks will spin down after the specified time The system disk will stay active If you configured a RAID containing all disks the spin down function will have no affect since the system files are included in the RAID volume Mighty Box Manual 13 ONE ONE Technologies Setting up a RAID in the RAID Setting menu Depending on the recent configuration of your Mighty Box the following screen can appear in different ways 1 If all disks have already been formatted and mounted as individual volumes the following screen will appear RAID Setting ONE TECHNOLOGIES O E RAID system cannot be activated If need to set up raid system must remove system data on the hard disk www one lochnelegies cam Users and Groups File and Prin
23. e In a 4BAY system with four disks inserted the following configurations are possible a JBOD all disks will be shown individually b RAID in level 1 JBOD one disk will be mirrored to the second disk the remaining two disks will be shown individually c RAID in level O all disks will be combined to one large volume Mighty Box Manual Se ONE ONE Technologies d RAID in level O JBOD two or three disks will be combined to one large volume the remaining disks will be shown as individual drives e RAID in level 5 three disks will be combined to one large volume the fourth disks will be used to store rebuild data Only the capacity of three disks can be used to store data f RAID in level 5 JBOD two disks will be combined to one large volume another is used for related rebuild data and the fourth disk is not included in the RAID set and will be shown as individual drive To get more information about the differences advantages and disadvantages of the different RAID modes refer to the RAID chapter below Initial configuration After all cables have been connected and the device has been prepared for the first start like mentioned above you can power on the system by pressing the power button located at the front side of the Mighty Box Push the button until the device starts It can take several minutes until the boot procedure has finished As soon as you can see an IP number in the device display the boot process has
24. e for creating a RAID set O S Mighty Box Manual 15 ONE Technologies Disk Utility ONE TECHNOLOGIES Device Name Type Mount Point Status Encrypt Password Format Umount Health TotalSize www one tochnologies com 1 18 E Users and Groups dev ndd none unmount PASSED Bi File and Print OOOO ytes System Network Service Maintenance Soe i J l d Detail Feck Utiity dev ndc none unmount PASSED RAID Setting Firmware Upgrade r Save ee ration Restore Configuration dev hdb unmount Urnount Detail Factory Reset PASSED Log File ee J l H ah idevinda mntfide1 mounted PASSED Detail Focal The disk utility shows the single disk as NTFS formatted volume while the rest is yet unused To create a RAID set just select the disks to be included in the RAID menu and select the appropriate RAID level you want to use and click on CREATE RAID Confirm the information message and the RAID will be configured Depending on the selected level and the size of the included disks this process can take a while The disk status will indicate the progress of the process Mighty Box Manual 16 ONE ONE Technologies RAID Setting Raid level RAID 5 File system NTFS Raid Size 931 GB Raid Used 93 MB WDC WD5000AATS WDS000AAJS WDS5000AAJ5 WDS5000AAJS OOYFAO OOYFAO OOYFAO OOYFAO 500 GBytes 500 GBytes 500 GBytes 500 GBytes
25. e until the door begins to close Close the door to completely insert the drive and to push it into the connectors Keep in mind that this system is only suitable for SATA hard disks Inserting PATA IDE devices will damage the connector backplane To exchange a disk in an already configured system please refer to the appropriate chapter below and follow the instructions not to damage your configuration and to lose your data stored on the Mighty Box At last switch on the Mighty Box by pressing the power button on the rear side of the product The device is now ready for its first start Before you start You should take some time to think about a suitable configuration Depending on what purpose you intent to use the Mighty Box for there are several different configuration possibilities The offered RAID modes are combinations of data protection and speed improvement JBOD is also offered in case you just want to use the individual disks separately Changing the RAID mode always means reconfiguring the disks and therefore deleting all information stored at that time So please take some time to decide which the most suitable configuration for you is In a 2BAY system with 2 drives inserted the following combinations are possible a JBOD both disks will be shown as individual volumes b RAID in level 1 one disk will be shown since the other is always an exact copy of it c RAID in level O both disks will be combined to one large volum
26. encnomaneeeseeceee roe 35 R st re Configuratii cciasdsscsccsesniecencascaseseosouneteatunaswendesnnanassasbiaiwbdeereseansdiceseunnstsauchaweneesspeecnnneseasabanens 35 PACOY RO E 35 LOS UM 36 Mighty Box Manual SE ONE ONE Technologies Setup and configuration Package Content Mighty Box NAS system Quick start manual Network cable RJ45 Antenna Power supply and Power cord Keys for un locking the trays Hardware Setup Take the Mighty Box and its components out of the product packaging Place the Mighty Box on a flat and secure area Apply the antenna to the box by screwing it on the antenna socket at the rear side of the box Connect the included power supply with a current source 220 230V Connect the power supply with the Mighty Box Please pay attention to the correct direction of the plug Connect the Mighty Box with your network RJ45 network cable included The wired network connection is necessary for the first configuration of the Mighty Box Adding Removing or Replacing hard drives The trays are usually locked in delivery status The locks show the red indicator plate Use the small keys or the tip of a ball pen to move the slider to unlock status The flaps will remain without function as long as they are in locked status As soon as the tray is unlocked the flaps will open the tray and pull out the hard drive when pulling Remove the hard drive and insert another one Push the drive insid
27. er the port number to use for the FTP transfer port 21 is the common standard NFS Server Setting Enable Activate this checkbox if the Mighty Box shall provide access by the NFS protocol Guest Access Setting Enable Activate this checkbox to enable guest access Doing so will provide a guest share folder which can be accessed by guests without user account Disabling this option will delete the guest share folder user and group Enable Quota To limit the storage capacity in the guest share folder enable this option and enter the maximum size of the guest folder This option is only available if the file system is ext2 or ext3 After all settings have been configured click on save to confirm and save all changes Mighty Box Manual 25 ONE ONE Technologies Share Management Share Management md2_share_folder Disk ou coos ONE public testshare Existing Shares Users and Groups File and Print File Server t Share Management Share Name Printer Server AjaXplorer Path mntfidel sys System HDesrtpton Network Service Optional Maintenance Windows FTP Access NFS Access Save SEIS Shae Log File The share management allows to change or delete existing shares and to create new shares To delete a share select it from the list and click on Delete Share To add a new share select ADD SHARE from the list and enter a share name in the Share Name fie
28. g ONE TECHNOLOGIES O E wwwione lechnelogies cam Users and Groups File and Print System Network Service DHCP Server Bonjour Blorrent Media Server Maintenance Log File MAC Address Existing Static IP Static IP Address ED Clean form END LIST Delete Static IP Enter the IP number you want to reserve under Static IP Address and enter the MAC address of the corresponding device Click on Save to add this IP number to the list of reserved numbers To delete an existing static IP select it from the list and click on Delete Static IP Bonjour Setting ONE TECHNOLOGIES ONE www one lechnelogies cam Users and Groups File and Print System Network Service DHCP Server Bonjour Blorrent Media Server Maintenance Log File Bonjour Setting Enable ITunes Enable save If you want to use the Mighty Box in an Apple Macintosh network you can enable Bonjour to make the system visible at Macintosh computers If you want to stream music files to Apple iTunes activate the iTunes Enable checkbox Doing so will create a folder named music inside the public folder The Mighty Box can then be found by iTunes and will provide all files inside the music folder inside iTunes for streaming Mighty Box Manual 32 BTorrent ONE Technologies B Torrent Max bandwidth down KB s 5 a a tra lt O E wW h technologie
29. he Refresh button to update the download information immediately 33 Mighty Box Manual ONE Technologies Media Server Media Server ONE TECHNOLOGIES O E Media Path l i media WWW one Teena ogai com Media Scan Time minite 60 Users and Groups SAVE File and Print kaua System Network Service DHCP Server Bonjour Blorrent Media Server Maintenance Log File To use the Mighty Box as an UPnP Media Streaming Server you can install an add on package which will install the media server components After the media server has been installed you can use this menu to configure the path or folder in which the media files are located for streaming Media Scan Time Enter the number of minutes for the interval the Mighty Box scans the content of the media folder for changes If you copy new media files to the streaming folder they will be available at streaming clients after the next scan interval Click on Save to store your settings MAINTENANCE MENU For information about DISK UTILITY and RAID SETTINGS please refer to Chapter XXX Firmware Upgrade Firmware Upgrade Current Firmware Version 20100615 1734_OneTechnologies 4bay 2561 ONE TECHNOLOGIES O E p wewoone lechnologies cam Upgrade File Durchsuchen PUparade Users and Groups File and Print System Network Service Maintenance Disk Utility fare eee RAID Setting Firmware Upgrade Save Configuration Rest
30. ing system of the Mighty Box Typ File system of the disk ext2 ext3 FAT32 NTFS or none Mighty Box Manual 10 ONE ONE Technologies Mount Point mount point in the internal operation system of the Mighty Box Status mount status of the disk mount unmount raid used Encryt Password Format Type Format In this column the file system can be selected and the disk can be formatted afterwards If needed the disk can be set to encrypted so data can only be accessed inside this device This option is only available if the file system is set to ext2 or ext3 After checking the option box you have to enter a password to activate the encryption of this disk Scandisk this function will start a scan of your disk to check it for possible errors Unmount this button will unmount a device It is only available for USB disks or USB pen drives connected to one of the rear USB ports of the Mighty Box to allow a secure removing of the devices Health The Mighty Box can read out S M A R T information from the hard drive if this feature is provided by the disk So PASSED or FAILED will represent the last results from S M A R T reading Click on Detail to see the complete S M A R T report Total Size shows the total capacity of the corresponding disk In the shown example the Mighty Box is configured with two disks set up as RAID and two more disks configured as independent disks in JBOD mode formatted as ext3 file system JBO
31. irectly and access the internal storage volumes according to their user settings Additionally the Mighty Box provides access to your network for all connected devices Choose STA Mode if the Mighty Box shall behave as a regular WLAN enabled client device This means the Mighty Box can be connected to an already existing access point in your network Other clients cannot directly connect to the Mighty Box but access through the network is possible SSID Enter the SSID name which shall be used to find the Mighty Box in the wireless network Hide SSID Activate this checkbox if the SSID shall not be visible when other devices are scanning the wireless network If the SSID is hidden only devices knowing the name can establish a connection to the Mighty Box Country Region Select the WLAN standard according to your location from the pull down list Channel Select a channel number from the list The Mighty Box will use this channel to communicate with other wireless devices Change the number if other devices in your nearer location are already using this channel number This may reduce connection problems or slow data transfer Wireless Mode By default the Mighty Box supports both transfer standards 802 11B and 802 11G and detects the supported speed of connected clients automatically If devices are not correctly identified you may want to select a fixed standard from the list Usually this is not needed and should be kept as Mixed
32. isers and Grou e IP Address 197 166 271 181 File and Print MAC Address 00 14 D7 05 01 14 LHL Servi RAID 108MB 1430804MB letwork Service aE eee Mantena HDD3 128MB 2347 29MB al CR ho 264MB 468440MB Select Disk Utility from the Maintenance menu list System Information Product Name MIGHTYBOX petra pared ape ete eget O E Firmware Version 20100615 1734_OneTechnologies_4bay_rt2561 Product Vendor ONE Technologies File and Print MAC Address 00 14 D7 05 01 14 a sem Servi RAID 108MB 1430804MB etwork Service Wa 3 Ps Sea ae ile UEP Pe hE HDD1 264MB 466440MB Disk Utility RAID Setting Firmware Upgrade Save Configuration Restore Configuration Factory Reset Log File After the system has read and checked the recent hard drive configuration the Disk Utility will be shown This can take several seconds depending on the configuration The Disk Utility is helpful in checking the recent configuration status Disk Utility aan 8 IS E E Encrypt Password Format Se Se Ham Wich POINT TL CANIS moun MEANN Ulalo Device Name po Point Status Type Format Scandisk Umount Health TotalSize encrypt idev hdd ex3 v E PASSED Format llencrypt idewihde ext3 mntide3 mounted ex3 ea PASSED _lencrypt idev hdb ex3 ial PASSED SU C encrypt idevihda imntfidet ex3 EE PASSED Format PRefresh The table shows the following information Device Name device name in the internal operat
33. izard oes eer ne een al eat Sar ee ee Add User Description Optional testshare for demonstration Add Group Add Share To add a new folder share select Add Share from the Quick Setup menu Mighty Box Manual 21 ONE ONE Technologies Enter a name for the new share and select the volume where it shall be located from the pull down menu named Path Enter a description if needed it s optional Click on next to proceed Step 2 3 Windows FTF Access testshare C Grant access to all Access Granted Access Denied END LIST lt lt Read Only admin guestshare lt Writable testuser quest share testgroup Remove gt gt END LIST The prefix denotes Group Name The second step allows you to select which user or user group marked with shall have access to this share Like in the user management you can specify in which way users and or groups can access this share Select users or groups from the right window and click on Read Only to add them with read only access to the Access Granted list or click on Writable to grant full access To remove a user or group from the Access Granted list select the user or group from the left window and click on Remove If you want to create a folder with no access restrictions you can activate the Grant access to all option In this case everybody will be able to access this folder share without any
34. ld Select the volume on with the share shall be created from the drop down list The description field is optional Clicking on Save will create the share To configure the Windows FTP Access and NFS Access for a share select it from the list and click on the corresponding button to enter the appropriate configuration menus Clicking on Clear Form sets all fields back to blank in case you entered wrong information you do not need to delete the field manually Printer Server Setting Printer Server Setting l x Enable FJ EH e eene E usbipo Description optional Canon iP6000D Users and Groups ES File and Print ee File Server Share Management Ponter Server AjaXplorer System i Network Service Maintenance Log File The Mighty Box allows making a regular USB printer accessible via LAN and WLAN To use this function connect a USB printer to one of the USB port on the rear side of the Mighty Box and activate the enable checkbox Printer Name shows the printer name used by the Mighty Box system Description shows the name or description of the printer if supported by the printer Click on save to confirm your settings The printer is now accessible as network printer in windows networks To make it show up in Macintosh networks select Enable Bonjour additionally in the Network Service menu Mighty Box Manual 26 ONE ONE Technologies AjaXplorer Aja
35. nstalled firmware version of the device as well as its IP number and MAC address Additionally the actual hard drive configuration is shown including information on used and free capacities of each existing volume Menu Buttons By clicking one of the main menu buttons located at the base of the window further menus can be accessed Setup SETUP menu Pressing the setup menu button will lead you to additional menus which are intended to be used for setting up the basic configuration users user groups and folder shares Administration ADMINISTRATION menu The administration menu offers the detailed configuration of the system System Info SYSTEM INFO Pressing this button will lead you to the basic configuration overview as shown directly after logging in to the system Exit EXIT Use this button to log off from the system Power Off POWER OFF This button can be used to shutdown and power off the device as well as forcing a restart of the system Mighty Box Manual s5 ONE ONE Technologies Quick setup by using the SETUP MENU For a quick and easy initial setup of the system the usage of the wizards provided inside the Setup menu is recommended Click on the green Setup menu button at the bottom of the screen and choose the option Quick Setup from the side menu afterwards system Information Produktname ONE TECHNOLOGIES Ste FER www one lechnologies cam O E Firm
36. ore Configuration Factory Reset Log File _ If a newer firmware is available download or save it to your local computer Click on browse in the Firmware Upgrade menu and locate the firmware file on your computer and select it Click on the Upgrade button to start uploading the file to the Mighty Box and initiating the upgrade process The system will restart after the upgrade has finished Mighty Box Manual 34 ONE Save Configuration ONE TECHNOLOGIES www one lochnologies cam Users and Groups File and Print System Network Service Maintenance Disk Utility RAID Setting Firmware Upgrade save Configuration Restore Configuration Factory Reset Log File ONE Technologies Save Configuration You can Save Download the configuration file to your PC_To save the server configuration click the Save button To save your actual settings to your local computer for backup reason click on save to download a configuration file containing all settings of the Mighty Box Restore Configuration Restore Configuration You can Restore Upload a previously saved configuration file from your PC To restore the ONE TECHNOLOGIES O E server configuration select the file you wish to restore and click the Restore button www one technologies com Restore File Users and Groups Restore File and Print System Network Service Maintenance Disk Utility RAID
37. ou want to setup date and time manually choose none from the NTP Server list Doing so will enable the date and time fields Now date and time can be entered manually This is not recommended because the Mighty Box does not have a battery buffered memory which could store and update date and time when the Mighty Box is switched off Date and time entries will get lost every time the system is switched off Therefore it is recommended to use a time server In this case the system will update and adjust these settings while starting up automatically Mighty Box Manual 29 ONE ONE Technologies Information System Information Product Name MIGHTYBOX CO E O E Firmware Version 20100615 1734_OneTechnologies 4bay_ 2561 Es Product Vendor ONE Technologies Users and Groups IP Address 192 168 1 10 File and Print MAC Address 00 14 D7 05 01 23 System RAID 93MB 953874MB _ LAN Settings usp OMB OMB bd HDD1 425MB 475909MB Information Disk Usage Network Service Maintenance Log File Select the Information menu to get an overview of some important system information You see product name and firmware version as well as the product vendor Also the actual IP number and MAC address is shown Further you see information about the disk configuration and the disk usage for each volume For detailed information about the disk usage the next menu will help Disk Usage Disk Usage Last Checked 8 8 2010 22 28 06 ONE TECHN
38. rs etc in your network you can leave the obtain IP address automatically option active In this case the device will get his IP address and the appropriate DNS server information from your DHCP server If one or both information has to set up manually check the use following option and enter the information on IP number subnet mask gateway and DNS server addresses at least one is needed secondary and others are optional After finishing your IP settings click on Next to proceed with the next step AI 5 Step Time Sttings Step 5 6 Time Settings ONE TECHNOLOGIES O E www one tochnologies com Date Month 1 Day 1 Year 2010 Quick Setup Time Hour 5 Minute 41 AM Wizard Time Zone GMT Greenwich Mean Time Edinburgh London X Add User Add Group NTP Server ga Default time nist gov v Add Share User Define Ea Dei Cancel In this step you can change the time settings of the Mighty Box It is highly recommended to use a time server to set up time and date To do so please choose the correct time zone from the drop down menu and choose one of the provided time servers from the list You can also enter a dedicated time server by clicking on User define and enter the servers address in the according field If you want or need to set up the time and date information manually choose none from the time server list Doing so sets the Date and Time selection menus active and allows you to set time and date
39. s com Max bandwidth up KB s 1 Users and Groups Save File and Print System RER Service Open torrent file Durchsuchen DHCP Server Torrent File Location _BONJOUL BTorrent Add Media Server Maintenance Log File The Mighty Box has an integrated BTorrent client You can use this function for unattended bit torrent downloads Set the maximum bandwidth for up and download in KB s in the first two fields to limit the bandwidth usage for BT transfers By entering a limit you can assure that there is enough bandwidth left for other connections and data transfers from users To initiate a BT download download the seed file to your client computer and click on the browse button in this menu and select the seed file on your computer Click on add to upload the seed file to the Mighty Box The information provided by the seed file will be shown in a list of all queued downloads B Torrent Max bandwidth down KB s 5 Max bandwidth up KB s L Durchsuchen Open torrent file Torrent File Location Add Percentage Download Upload Client Status 0 kb s 0 stop Start Ste ID Name Size 1 000 3 2 1 Win_x86_install_deexe torrent 144 3MB 0 D kb s Click on start to start the download The downloaded file can be found in the btdown folder inside the public folder once it is finished To stop a download click on Stop and if you want to delete a download from the list click on Delete Use t
40. ser button If you want to add the new user as a member to an existing user group click on Groups to show the available user groups and use the add and remove buttons to change the membership settings Mighty Box Manual 23 ONE ONE Technologies User Management testuser Member Non member quest share EN END LIST ENDLIST RER Ea Sat Click on save to confirm your settings or choose Cancel to leave the menu without making any changes Groups Similar to the User Management you will see all group settings on one page Group Management i o e guestshare eco ONE testgroup ADD GROUP Existing Groups Users and Groups User Management Group Management File and Print System Group Name Network Service a ma alete C Maintenance Ea Weis La BESS Log File To change the members of a group select it from the list and click on Members to see a list of all users included in this group You can now add or remove users from the group To delete a group select it from the list and click on Delete Group To create a new group select ADD GROUP from the list and enter a group name in the Group Name field Click on save to create the new group If you want to add some users to the new group select it from the list and click on Members to get to the member list
41. t System Network Service Maintenance Disk Utility SSE RAID Setting Firmware Upgrade Save Configuration Restore Configuration Factory Reset RAID system does not exist laa ae dev hda dev hdb dev hdc dev hdd WDS5000AAJS WDSO00AAJS WDS000AAJS WDS5000AAJS OOYFAO OOYFAO OOYFAO OOYFAO 500 GBytes 500 GBytes 500 GBytes 500 GBytes The disk status shows RAID system does not exist since all disks are already in use and mounted as single volumes On top of the hard drive overview the button Remove system data is now available If you want to change the configuration from JBOD to RAID you have to remove the existing data from the disks by clicking the Remove system data button Doing so will delete ALL existing data from ALL disks After the system and all other files too have been removed the Mighty Box will perform a restart Login to the system and select the RAID Settings menu again System Information Product Name MIGHTYBOX GE e O E Firmware Version 20100615 1734_OneTechnologies 4bay 2561 Product Vendor ONE Technologies EE IP Address 192 168 21 193 Network Service MAC Address 00 14 D7 05 01 23 Maintenance Log File Found New Disk Please Format Mighty Box Manual 14 ONE ONE Technologies The menu will offer different options now RAID Setting ONE TECHNOLOGIES ONE Raid level RAIDO RAD1 RAIDS Linear File system EXT2 2 EXT3 NTFS Sys
42. tem Network Service Create raid system Maintenance Disk Utility 3 RAID Setting Disk Status Firmware Upgrade Save Configuration RAID system does not exist Restore Configuration Factory Reset Log File WDC WDC WDC WDS000AAJS WD5000AAJS WD5000AAJS OOYFAO OOYFAO OOYFAO 500 GBytes 500 GBytes 500 GBytes 500 GBytes Now all four disks are available for creating a RAID set Tick the checkboxes of all disks you want to include in your RAID System Depending on the number of disks you select the possible RAID levels will change Selecting two disks only let the RAID O RAID 1 and LINEAR option become available Selecting three or four disks let the RAID 1 become unavailable because RAID 1 can only be configured with two disks Therefore RAID O LINEAR and now also RAID 5 are available If you do not use all disks for creating your RAID set the remaining disks can be formatted as single volumes by using the DISK UTILITY afterwards 2 If one or more disks have been already formatted as individual volumes the menu will look like the following example RAID Setting Raid level RAID 0 RAID 1 RAID 5 Linear File system EXT EXT3 NTFS Disk Status RAID system does not exist dewhda WDS5000AAJS WDS000AAJS WDS5000AAJ8 WDS5000AAJ8 OOYFAO OOYFAO OOYFAO OOYFAO 500 GBytes 500 GBytes 500 GBytes 500 GBytes Here the first disk has already been used as a single volume The remaining three disks are availabl
43. tored on different drives Due to the parallel distribution the speed of read write processes will increase compared to a single drive The disadvantage of a RAID 0 is that it offers no data security If one drives fails all data is lost since each drive stores only a part of each file The total capacity is the combined capacity of the included drives if capacity of all drives is the same If drives of different sizes are used the total capacity is the smallest capacity multiplied with the number of drives To setup a RAID 0 a minimum of two drives is needed RAID 1 RAID 1 is also called mirroring Exact two drives are mirrored which means the data stored on one disk will automatically be copied to the second drive as well If a drive fails all data is still provided on the mirror drive The total capacity of a RAID 1 is the capacity of 1 hard disk Mighty Box Manual hie ONE ONE Technologies This RAID Level provides the highest data protection level but has no advantage in speed or performance To setup a RAID 1 two disks are needed and they should be the same size Otherwise the smaller disk size is the one which can be used RAID 5 To setup a RAID 5 at least three disks are needed One of the disks will be used to store parity data which will be used to rebuild data after a defective hard drive has been replaced The biggest advantage of RAID 5 is to have a good data protection without losing too much capacity Only the capacit
44. ur network Since all network information fields are optional you can choose which settings will be configured automatically at the clients side and which will not All data which is not entered here must be configured manually on the client devices So it is recommended to enter subnet mask default gateway and primary DNS server as minimum information DHCP IP Address Start Enter the start IP address which shall be used to configure clients DHCP IP Address End Enter the last IP address available for distribution to clients Make sure that the static IP number of the Mighty Box itself is NOT included in the DHCP number range The range between start and end address will define the maximum number of clients which can be configured for network access Maximum Lease Time Specify the time an IP number will be reserved to a dedicated client device If you use a lot of different devices choose a short period so the numbers can be reassigned to other devices soon To check how many clients have been connected to the box and IP numbers have been reserved at the moment click on DHCP lease list to see a table of all used IP numbers If you want to make sure that one or more devices will always receive the same IP number regardless of the lease time settings you can reserve dedicated numbers to these device Click on Static IP number to get to another submenu Mighty Box Manual 31 ONE ONE Technologies Static IP Settin
45. want to change it right now or maybe already have changed it simply click on Next to keep the current password If you want to change the password enter the new password in the first field and repeat it in the second field to avoid mistyping Also here confirm the changes by clicking on Next 3 Step Hostname ONE TECHNOLOGIES ONE www one technologies com Quick Setup Wizard Add User Add Group Add Share Step 3 6 Hostname Setting MIGHTYBOX NOTE The Hostname is the name given to the server by which Window based machine may access Hostname Back f Next ECO e cO O By default MIGHTYBOX will be the name the Mighty Box will use for identification in your local network You can change the hostname of the device here if you want to or keep it by clicking on Next to go on with the next step Mighty Box Manual ONE Technologies 4 Step Internet Protocol Settings Step 4 6 Internet Protocol Setting Shei cine tone ONE iets a Shoat ot IP Address Obtain IP Address automatically Quick Setup Use following IP Address Wizard IP Address Add User Add Group Subnet Mask Add Share Default Gateway DNS Server Obtain DNS Server Address automatically Use following DNS Server Address Primary Secondary Others Back a cance This menu allows you to configure the network settings of your Mighty Box If you are using a DHCP server often present in internet route
46. ware Version Quick Setup i s Produkt Hersteller IP Adresse MAC Adresse HDD4 HDDS HDD HDD1 MIGHTYBOX 20100505 1031 _OneTechnologies 4bay 2561 ONE Technologies 1927 163 21 205 00 14 07 05 01 14 123MB 704175MB 128MB 234729MB 123MB 704175MB 160MB 466440MB Choose Wizard from the submenu Now you will be lead through 6 easy steps of configuration LU Step Language Setting ONE TECHNOLOGIES ONE www one teochnologies com Quick Setup Wizard Add User Add Group Add Share Mighty Box Manual Step 1 6 Preference Language Setting admin Language Preference Engilish O 009g Please choose your preferred language from the drop down menu and confirm your selection by clicking on Next All menus will be shown in your selected language from now on ONE Technologies 20 Step Password Setting ONE TECHNOLOGIES ONE www one technologies com Quick Setup Wizard Add User Add Group Add Share Step 2 6 New Password Setting admin New Password DUT Seseeeeeeegeeegeeg Please type your password again NOTE If you do not wish to change the password click Next button to advance to the next step Back Ip Next SR DO In the second step of this wizard you will be asked to change the password of the user currently logged in here admin This would be the right time to change the preconfigured admin password into a secure and secret password If you do not
47. xd e Uno ab idewihdd none N e Bie PASSED Detail j GBytes Format encrypt raid 500 i l gt T 1 LIF idewhde none Ze e Bee PASSED GBytes encrypt raid apa i 500 est MM cap Urrira d idewihdb none ised e SLO MULUS PASSED Detail GBytes Elencrypt idevihda ntfs mntide1 mounted ex3 v ES ME asso E 2 e e GBytes ormat PRetresh As soon as a RAID set has been created it will also been shown in the disk utility All RAID member disks will be shown as raid used in the status column Users Groups and Shares To grant access to the Mighty Box for different people each of them needs to be set up as a user in the Mighty Box system If you have to manage many users the system allows creating user groups Users can be collected into groups to grant or deny access for the whole group at once Rules applied to a user group will become active for all users belonging to that group So user management can be easier using groups if you have many users to manage Shares are folders created on the Mighty Box which can be accessed by users according to their user settings You can control who can access a share and who cannot By default there are two users already existing admin and guest share Both of them belong to the system and cannot be removed or renamed To enable other users in your network to access the Mighty Box new users have to be created in the system There are two
48. y of one disk is lost regardless of setting up a RAID with 3 or all 4 disks If one hard disk fails it can be replaced by a new one and the RAID 5 system will start to restore the lost data be recalculating them using the parity data and the remaining hard drives When setting up a RAID in Level 0 1 or 5 the resulting capacity is related to the smallest hard disk included in the RAID Example Setting up a RAID O with 1x 250GB and 1x 320GB disks the resulting usable capacity will be 500GB 2x 250GB the remaining part of the 320GB drive 80GB will be inaccessible Therefore the usage of equal sized hard disks is recommended for setting up RAID systems To setup disks as individual disks JBOD the DISK UTILITY is the correct menu to use If you want to create a RAID the RAID SETTINGS menu is the one to use Configuration of JBOD volumes Please select the Disk Utility from the maintenance menu After some seconds the following menu will appear Disk Utility Encrypt Password Format Scandisk Umount Health TotalSize Device Name Type Mount Point Status Type Format encrypt Idevihdd ntfs mnt ided mounted ex3 vo ES Baler MA er Format encrypt fdevinde ntfs mntfide3 mounted ex3 ES RS passe Sr A encrypt E E SS wem 500 fdevihdb ntfs mnt ide2 mounted ES MEE passe GEL GBytes AIS fdev hda ntfs mntfide1 mounted XLS can Urmount
Download Pdf Manuals
Related Search