Spring Clamp Terminal Block Model Q6TE
Contents
1. A MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE 1 8 12 OFFICE TOWER Z 14F HARUMI CHUO KU 104 6212 JAPAN NAGOYA WORKS 1 14 YADA MINAMI5 HIGASHI KU NAGOYA JAPAN MODEL Q6TE 18S U JE MODEL CODE 13JT72 IB NA 0800204 B 0506 Spring Clamp Terminal Block Model Q6TE 18S User s Manual 1 Overview This manual explains how to use the spring clamp terminal block model Q6TE 18S hereinafter referred to as the Q6TE 188 The Q6TE 18S shall be used attached to a Q Series terminal block type I O module or an intelligent function module Since the Q6TE 18S uses a spring clamp it does not require screw tightening which greatly reduces the number of wiring procedures Be sure to carefully read QCPU User s Manual to ensure the safe and correct usage of this product before using it 2 Compatible Models The Q6TE 18S can be used with the following models Model type QX10 QX28 I O module QY10 QY18A QY70 QY80 Q62DA Q64DA Intelligent function module Q64AD Q68ADV Q64TCRT Q64TCRTIBW Q64RD QX40 QX40 S1 QX70 QX80 QY22 QY40P QY50 QY68A QX48Y57 QI60 Q68DAV Q68DAI Q68ADI 3 Specifications Specifications Applicable wire size 0 3 to 1 5 mm AWG22 to 16 Wire strip length 8 to 11mm Mounting screw tightening torque range 0 66 to 0 89 Nem Weight 0 07kg 4 Removal of Terminal Block and Installation of Q6TE 18S 1 Removal of terminal block e Unscrew the two terminal block mounting screws situated at the2. t might be broken Circular shaped hole oy Wire strip length 8mm to 11mm 1 2 Cable removal Insert the tool into the corresponding square shaped hall until it stops Pull the wire out of the hall completely 6 External Connections The terminal numbers of the Q6TE 18S correspond to the terminal numbers on the compatible module For the signal names corresponding to the terminal numbers when connected to an external device please refer to the User s Manual of the module to use 7 External Dimensions Q6TE 18S Installed on a module Example QX10 nn L o OCE om o a 0 0 O 0 Os T OcO A DO oO Os a a ps OsO 9 O0 N DO CS O0 D OO O0 a DO N Orel Oro a A N Ore p _27 23 J 90 1 06 0 91 3 54 i Unit mm inch The depth of the module installed with a Q6TE 18S is equivalent with the factory default dimensions for that module Printed in Japan on recycled paper
3. top and bottom of the terminal block e Gently remove the terminal block 2 Installation of Q6TE 18S e Attach the Q6TE 18S to the module e Tighten the terminal block mounting screws within the specified torque range gt Terminal block Module Q6TE 18S CUTTY LI E I Terminal block mounting screw 5 Cable Installation Procedure 1 Cable Installation Insert the tool into the square shaped hole which corresponds to the terminal you wish to use While the tool is inside the hole insert the wire into the circular shaped hole as shown below Remove the tool from the square shaped hole taking care not to remove the wire After the wire has been clamped gently pull the wire to confirm that it is secure Square shaped hole Caution 1 Take care that the wire strip length is between 8mm to 1imm If the wire strip length is too long this will expose the bare wire which increases the risk of electric shock or short circuit If the wire strip length is too short this will result in the wire not being securely attached 2 When mounting removing the cable make sure to use the dedicated tool i e a tool dedicated to spring clamp terminal block and insert the tool vertically into the hole If a general slotted screwdriver is used instead of the dedicated tool or the tool is not vertically inserted the spring clamp terminal part or terminal block resin par
Download Pdf Manuals
Related Search