Vandal Proof / Lightweight Fixed Dome IP Camera Installation Guide
Contents
1. Vandal Proof Lightweight Inner Cover Inner Cover Unscrew the Module fastened Screw with the screwdriver as indicated in the figures below Vandal Proof Lightweight Step 3 Press the sides of the Snap on Camera Module and detach it from the Dome Camera s Housing Plate Vandal Proof Lightweight NOTE Users may use a coin to A screw off the conduit entry block for the Vandal Proof Fixed Dome IP Camera 14 Step 4 Attach the Camera Housing Plate s base to the In Ceiling Mount s top plate aligning the camera s rear cable entry with the entry hole on the In Ceiling Mount s top plate Align the three Captive Screws with the mating screw holes on the Camera Housing Plate s base Then tighten the three Captive Screws as shown in the right figure Step 5 Position the supplied adhesive backed Ceiling Sticker Diameter 176 mm onto the ceiling where the Camera will be mounted and cut the ceiling hole using the template as a guide Step 6 Insert the Dome Camera with the attached In Ceiling Mount into the ceiling hole and run the Ethernet Cable through the desired cable entry Vandal Proof Step 7 Secure the Unit to the ceiling NOTE Do Not over tighten the three fixing screws If using a power tool the slip clutch should be set to the lightest setting or the clamps could be damaged The In Ceiling Mount s Wing Clamps will draw the Dome Camera Housing2. The Standard Pendant Mount is supplied with four M8x30 Hex Head Machine Screws for the convenience of installation by fastening the Pendant Mount with other metal part together Spring Washer 8 Plain Washer 8 Step 6 Thread the Ethernet Cable through the entry of the Dome Camera s Housing Step 7 Rotate the joint of Dome Camera Housing into the entry of the Pendant Mount aligning the screw hole of the joint with the one of the Pendent Mount Step 8 Fix the camera housing with the supplied Spring Washer 8 M8x16 Hex Head Stainless Steel Screw Pendant Tube Washer Rubber Washer 8 and Washers Step 9 Attach the Snap on Camera Module to the Dome Camera Housing and tighten the Module fastened Screw 29 30 Step 10 Connect the RJ 45 Cable to the Camera Module to access the camera for viewing video and then adjust the Dome Camera lens to a desired angle NOTE The zoom level and focal A length might be different with the Dome Cover on In this case adjusting zoom level and focal length through the Dome Cover is recommended Step 11 Put the Inner Cover back to the Camera Module Step 12 Close the Dome Cover and tighten the two Captive Security Screws Installation Completed Cable Gland Installation Kit Cable Gland Installation For Vandal Proof Dome Indoor housing cable connection can be protected from water damages by installing the all in one cable with a cable gland 1
3. 18 Step 16 Align the 3 holes in the Trim Ring with the Retaining Nut on the In Ceiling Mount and snap the Trim Ring in place to complete the installation 1 3 4S Mount Electrical Box Before installing the IP Dome Camera in the 4S Electrical Box please unscrew and open the Dome Cover with the Security Torx Follow the steps below to install the 4S Mount Electrical Box Figure 4 4S Mount Electrical Box pn E GEN daags Pa Housinc Step 1 Run the wires Ethernet and power through the 4S Mount Electrical Box AN NOTE The Power Cable is omitted if using PoE Step 2 Disassemble the Dome Camera s Inner Cover see the illustration in 1 1 Hard Ceiling Step 3 from the Camera Module Step 3 Detach the Snap on Camera Module from the Dome Camera s Housing Pleat by unscrewing the Module fastened Screw first Then press the sides of Camera Module and pull it slightly out of the Housing Plate 20 Step 4 Thread the Power and Ethernet Cables through either the side conduit entry or back conduit entry Then fasten the Dome Camera s Housing Plate on the Electrical Box with the two screws Vandal Proof Lightweight Step 5 Connect the power and Ethernet Cables to their connectors on the Camera Module Step 6 Attach the Snap on Camera Module into on the Dome Camera s Housing Plate Screw on the Module fastened Screw to secure the Camera Module Step 7 Access the camera browser viewer for vi
4. Plate to the ceiling board until it is completely flush with the board Lightweight 15 Figure 3 Bottom View of installed In Ceiling Mount Vandal Proof Lightweight Step 8 Attach the Snap on Camera Module to the Dome Camera Housing Plate For Vandal Proof IP Dome Camera please install the Camera Module with the terminal blocks facing the side cable entry Step 9 Tighten the Module fastened Screw Step 10 Connect the Ethernet Cable to the camera s network connector Refer to the Camera Quick Guide for details regarding the Camera Connector Definition Step 11 Access the Camera Browser viewer for viewing images Please refer to Chapter Accessing Camera in IP Camera User s Manual for further details Users can also use the Camera s BNC Connector for video output while choosing BNC as one of the streaming options in advance Step 12 Adjust the Camera to a desired angle by adjusting the Pan Tilt Rotation Pan adjustment range is nearly 360 rotation angle range approaches to 270 Tilt angle is adjustable between 10 90 NOTE Adjust the Lens carefully within the limits mentioned above or the cables underneath would be harmed Step 13 Adjust the Zoom Ring Screw to set the desired zoom subsequently modify the Focus Ring Screw to set the desired focal length Step 14 Reinstall the Plastic Inner Cover Step 15 Close the Dome Cover and tighten the two Security Screws
5. Proof Lightweight Step 3 Press both sides of the Inner Cover and remove it from the Camera Module Vandal Proof Lightweight Inner Cover Inner Cover Step 4 Unscrew the Module fastened Screw with the screwdriver as indicated in the figures below Vandal Proof Lightweight Step 5 Press the sides of the Snap on Camera Module and detach it from the Dome Camera s Housing Plate as indicated in the figures below Vandal Proof Lightweight Step 6 Mark the positions of the four screw holes on the base of the Dome Camera at the chosen installation location Vandal Proof Lightweight Type 2 Step 7 In the marked locations drill each hole slightly smaller than the supplied Screw Anchors Step 8 Put the supplied Anchors into these drilled holes Step 9 Fasten the Dome Camera s Housing Plate with the four supplied Self tapping Screws Vandal Proof Lightweight N NOTE Be sure to fix the Self tapping Screws with the Rubber Washers Vandal Proof Lightweight Step 10 Thread the cables Power Ethernet Audio Alarm through either the side conduit entry or back conduit entry as illustrated below Users may use a coin to screw off the conduit entry block for Vandal Proof IP Dome Camera Side Conduit Entry Back Conduit Entry AN NOTE The Power Cable is omitted if using PoE Step 11 Connect the ports on the Camera Module with their cables wires respectively as shown in the
6. Silicone Rubber Ring 2 Cable Gland Cable Gland First insert the silicone rubber ring into the cable gland body from the top as shown on the right Before starting the installation of the all in one cable with the cable gland please refer to section Hard Ceiling installation gt Step 1 9 for camera housing installation Then follow the instruction below Step 1 Loosen the thread lock sealing nut from the cable gland body and insert the all in one cable from the side with the network connector starting from the biggest size connector to the smallest size connector 4 Th read Lock Sealing Nut 31 32 Step 2 Insert the all in one cable to the cable gland body from the bottom starting from the biggest size connector to the smallest size connector as well Step 3 Twist in the thread lock sealing nut a little bit back to the cable gland body Step 4 Insert the all in one cable to the side conduit entry again starting from the biggest size connector to the smallest size connector Step 5 Attach the Snap on Camera Module into the Dome Camera Housing and screw the Module fastened Screw tightly with the screwdriver to secure the Camera Module Step 6 Plug in the connectors to their corresponding ports Then adjust the cable lines and twist in the cable gland body to the side conduit entry After the cable gland body is in fasten the thread lock sealing nut until the cable is completely cove
7. Vandal Proof Lightweight Fixed Dome IP Camera Installation Guide Indoor Outdoor Ver 1 3 003B02WXZXA3 Table of Contents INGOOF Camera INStAllAtiOn eg i0 enorme vebersnar nerede Elei ASA 3 1 1 EI eNO aeaa E ce tenn ean ae 3 1 2 In Ceiling T Bar Mountng sse see eee eee e ee 11 1 3 AS Mount Electical BOX EE 19 1 4 COrner eE Le eege 22 Outdoor Camera NEEN UE Le TEE 26 2 1 Standard Compact Pendant Mounting sese ee e e ee e 26 Cable Gland Installation css sss sss s sse eee eee eee 31 Mini Dome Mounting Kit Installation sss sss ss sss ss esse sees eee eee eee e 34 1 1 Indoor Camera Installation Hard Ceiling The Fixed Dome IP Camera can be installed directly on the wall or ceiling Please note that the wall or ceiling must have enough strength to support the IP Dome Camera Items Needed e Vandal Proof Lightweight Fixed Dome IP Camera e Ethernet Cable e DC Jack Cable required without PoE e Self tapping Screws supplied e Rubber Washers supplied e Plastic Screw Anchors supplied Tools Needed e Tools for drilling e Screwdriver Follow the steps below to install the IP Dome Camera Step 1 Unpack the Vandal Proof Lightweight Fixed Dome IP Camera package and take out the IP Dome Camera Step 2 Release the two Captive Security Screws with the supplied Security Torx and open the Dome Cover Vandal Proof Lightweight Figure 1 Captive Security Screw Vandal
8. amera module and detach it from the Dome Camera s Plate 35 36 Step 5 Thread the cable through the back conduit entry of the Dome Camera s Plate Then fix the Dome Camera s Plate to the mounting kit by screwing on four supplied M4x8 Machine Screws at the positions shown in the right figure Step 6 Connect the Ethernet Cable to the camera as shown in the right figure Step 7 Place the camera module back to the Dome Camera s Plate and tightens the Camera Fastened Screw with the screwdriver Step 8 Put the Dome Cover back to the camera and tighten the Captive Security Screws at each side of the cover
9. dal Proof Lightweight Step 16 Put the Inner Cover back to the Camera Module Vandal Proof Lightweight Step 17 Replace the Dome Cover back For Vandal Proof IP Dome Camera please align the arrow mark on the Dome Cover with the one on the Housing as shown in the left figure below For Lightweight Fixed Dome IP Camera please align the arc area on the Dome Cover with the back conduit entry as shown in the right figure below Vandal Proof Lightweight Step 18 Screw on the two Captive Security Screws on the side of the Dome Cover tightly to fasten the Dome Cover Camera installation is complete Vandal Proof Lightweight 1 2 In Ceiling T Bar Mounting The indoor Dome Camera can be mounted with the optional accessory In Ceiling T Bar Mount The items and tools needed for in ceiling installation are listed as follows In Ceiling Mount Package Contents i SN In Ceiling Mount Trim Ring Ceiling Sticker In Ceiling Mount Dimension Unit mm Tools Needed e Tools for drilling e Phillips Screwdriver e Security Torx provided TN 11 Follow the steps below to install the In Ceiling T Bar Mounting Step 1 Release the two Captive Security Screws with the supplied Security Torx and open the Dome Cover Vandal Proof Lightweight Figure 2 Captive Security Screw Vandal Proof Step 2 Press both sides of the Plastic Inner Cover and remove it from the Camera Module
10. e Step 2 Drill six holes on the wall and the ceiling to install six M4 plastic anchors Fix the Corner Mount on the Ceiling by fastening six M4 Self tapping Screws in the Plastic Anchors Step 3 Place the Dome Camera s Housing Plate in the Corner Mount NOTE Detach the Snap on Camera Module before placing the Dome Camera s Housing Plate into the Corner Mount 23 24 Step 4 Thread the RJ 45 Cable through the Dome Camera s Housing Plate Step 5 Tighten the four M4 Mechanical Screws to install the Dome Camera s Housing Plate in the Corner Mount Step 6 Place the Camera Module into the Dome Camera s Housing Plate until there is a click sound Step 7 Tighten the Module fasten Screw on the Camera Module to fix the Camera Module on the Dome Camera s Housing Plate Step 8 Connect the RJ 45 Cable to the Camera Module and then adjust the Dome Camera lens to a desired angle NOTE The zoom level and focal length might be different with the Dome Cover on In this case adjusting zoom level and focal length through the Dome Cover is recommended Step 9 Install the Inner Cover on the Camera Module Step 10 Place the Dome Cover back in position and tighten the two Captive Security Screws with the supplied Security Torx 25 Outdoor Camera Installation The Outdoor Vandal Proof Fixed Dome IP Camera could be mounted on the wall with the Standard Compact P
11. endent Mount for monitoring convenience Standard Compact Pendant Mounting Standard Pendant Mount Package Contents e M8x16 Hex Head Stainless Steel Screw x1 e Rubber Washer 8 x1 e Pendant Tube Washer x1 e Spring Washer 8 x5 e Plain Washer 8 x4 e M8x30 Hex Head Machine Screw x4 e Sponge x2 Compact Pendant Mount Package Contents e M8x16 Hex Head Stainless Steel Screw x1 e Rubber Washer 8 x1 e Pendant Tube Washer x1 e Spring Washer 8 x1 e Sponge x1 Standard Pendant Mount Dimension 348 K Unit mm Compact Pendant Mount Dimension 184 Unit mm Tools Needed e Tools for drilling e Tools for screwing e Security Torx supplied Follow the steps below to install the Standard Compact Pendant Mount Step 1 Unscrew the two Captive Security Screws with the supplied Security Torx Driver and open the Dome Cover Step 2 Press both sides of the Inner Cover and remove it from the Camera Module 2 28 Step 3 Unscrew the Module fastened Screw as indicated in the right figure Step 4 Press the sides of the Snap on Camera Module and detach it from the Dome Camera s Housing as indicated in the right figure Step 5 Fasten the Standard Compact Pendant Mount onto the wall securely Run the Ethernet Cable through the Standard Compact Pendant Mount as shown in the right figure M8x30 Hex Head Machine Screw for Standard Pendant Mount only
12. ewing images Please refer to the Dome Camera User s Manual for further details Users can also use the Camera s BNC Connector for video output while choosing BNC as one of the streaming options in advance Step 8 Position the camera at a desired angle through PTZ adjustment Please refer to the last section for illustration Step 9 Adjust the camera s zoom level and focal length via Zoom and Focus Ring Screws Step 10 Replace the Dome Cover back For Vandal Proof IP Dome Camera please align the arrow mark on the Dome Cover with the one on the Housing as shown in the left figure below For Lightweight Fixed Dome IP Camera please align the arc area on the Dome Cover with the back conduit entry as shown in the right figure below Vandal Proof Lightweight Step 11 Screw on the two Captive Security Screws on the side of the Dome Cover tightly to fasten the Dome Cover Camera installation is complete 21 1 4 Corner Mounting Corner Mount Package Contents Corner Mount M4 Plastic Anchors x6 M4 Self tapping Screws x6 M4 Mechanical Screws x4 Corner Mount Dimension 75 1 DZ es Unit mm Tools Needed e Tools for drilling e Phillips Screwdriver e Security Torx Supplied 22 Follow the steps below to install the Corner Mount Step 1 Match the Corner Mount at the ceiling corner Please note that the Dome Camera s Housing Plate installing holes are in position as the right figur
13. figures below Vandal Proof Lightweight Step 12 Attach the Snap on Camera Module into on the Dome Camera Housing Plate and screw the Module fastened Screw tightly with the screwdriver to secure the Camera Module AN NOTE For Vandal Proof IP Dome Camera please install the Camera Module with the terminal blocks facing the side cable entry as shown in the left figure below Vandal Proof Lightweight Mod IECH BTA CAN R E ais Step 13 Access the Camera Browser viewer for viewing images Please refer to User s Manual for further details Users can also use the Camera s BNC Connector for video output while choosing BNC as one of the streaming options in advance Step 14 Adjust the Camera s Pan Tilt Holder to a desired angle as shown below Pan adjustment range is nearly 360 rotation angle range approaches to 270 Tilt angle is adjustable between 10 90 Pan Adjustment Tilt Adjustment A NOTE Adjust the Lens carefully within the limits mentioned above or the cables underneath would be harmed Please tighten the Camera s Pan Tilt Holder Screw to secure the desired tilt angle after adjusting Vandal Proof Lightweight Step 15 Adjust the Camera s zoom level and focal length via Zoom and Focus Ring Screws NOTE The zoom level and focal length might be different with the Dome Cover on In this case adjusting the zoom level and the focal length through the Dome Cover is recommended Van
14. red After the above steps are completed please refer to section Hard Ceiling installation gt Step 13 18 for the remaining steps to complete camera installation 33 34 Mini Dome Mounting Kit Installation Mini Dome Mounting Kit 69PNX32X1M01 is designed to work with various kinds of pendants and tubes AN The Mini Dome Mounting Kit cannot be used for Vandal Proof Fixed Dome IP Camera Supported Model e Lightweight Fixed Dome IP Camera Dimensions of Compatible Pendant Tube e NPT e NPT 1 Mini Dome Mounting Kit Package Contents e Mini Dome Mounting Kit x1 e M4x8 Machine Screws x6 e M4x14 Machine Screws x4 e Silicone Rubber Ring x1 Items Needed e IP Camera e Ethernet Cable e DC Jack Cable required without PoE Tools Needed e Screwdriver e Security Torx supplied in the camera package ON Follow the steps below to install the camera onto the mounting kit Step 1 Fix the mounting kit onto the pendant tube NOTE If NPT 4 mounting accessory is used with the Mini Dome Mounting Kit please fit the supplied Silicone Rubber Ring on the mounting kit BEFORE fixing the mounting kit to the pendant tube Step 2 Remove the Dome Cover from the camera by loosening the two Captive Security Screws with the supplied Security Torx Step 3 Loosen the Camera Fastened Screw with the screwdriver as shown in the right figure Step 4 Press and hold the sides of the c
Download Pdf Manuals
Related Search