USER MANUAL - Falcon Technical Ltd
Contents
1. Portable Satellite Internet USER MANUAL For ASTRA 2 at 28 2 E Internet Portable satellite internet y 411 eae WWW ez et a CO u k ae WORLD LASS TECHNOLOGY About EZ Net Congratulations on your new purchase and welcome to the world of EZ Net Satellite Internet EZ Net is the simplest touring satellite internet system to set up and operate This guide will take you through the simple process required to get you online as soon as possible The EZ Net Satellite Internet Kit includes everything you need to get high speed broadband internet on the move Each kit includes the EZ Net diamond dish iLNB sturdy lightweight tripod with ground fixings a EZ Net elevation and alignment kit all the necessary leads and connections as well as a satellite modem and WiFi router The product can easily be transported and stowed away in the supplied carry bag and is quite possibly the lightest most portable product currently available on the market Please note that it is important to retain your receipt or proof of purchase so that we are able to assist and deal with any enquiries you may have EZ Net is a product and brand name of Falcon Technical Ltd using our patented smart satellite finding technology For more information on EZ Net and our products please visit our website www ez net co uk Get in touch EZ Net c o Falcon Technical Limited Hill Farm Northwich Road Dutton Cheshire WA4 4LE UK UK Enquiries2. Play Tool Status Configuration Overview alae Bear amp Modem State Error 001 Awaiting installer action Software Version 2 2 4 19 Terminal Installation est Outdoor Unit v 2W_Ka_ ILB2210 _ _75cm_ ANT2010 Spot Beam v 22 Antenna Pointing Restart Skip Pointing Click Skip Pointing to skip the pointing procedure use if the dish was already correctly pointed Setting Up the Point amp Play Tool The Point amp Play tool helps you to point the antenna correctly During the pointing procedure the Point amp Play tool can produce various sounds each having a specific meaning described below You will thus need to put on the headphone during the pointing procedure Ensure that the volume of the Point amp Play tool is not set too loudly otherwise damage to your hearing may occur Possible tones are P K l High uninterrupted tone correct tone Y The dish points to the correct satellite and is receiving the strongest signal you have the optimal pointing position 10 Medium or high interrupted tone The dish points to the correct satellite but does not receive the strongest signal so far As soon as you hear this tone you are sure that the antenna points to the correct satellite i i T Hi Low uninterrupted tone The dish is not pointing to a satellite or points to a wrong satellite fi n Do not stand in front of the iLNB of the antenna dish during poi
3. 01928 759 239 International 44 0 1928 759 239 Email contact ez net co uk Package Contents Thanks for purchasing EZ Net the easy to use satellite internet system With your purchase you will find the following contents ne Diamond Dish amp Arm Tripod amp Pegs iLNB Twin Coax Cable amp Point amp Play Kit Elevation Meter Connectors amp Compass Satellite Modem Mains Adapter Network Cable WiFi Router 12V to Mains Carry Case amp Mains adapter Inverter Getting Started Dish Setup When setting up the tripod take into account the orientation of the dish it should be pointing in a southeasterly direction and the dish must have a clear view towards the satellite without any buildings trees that may hinder the signal 1 Loosen the fixing clamp on the tripod stand and push the legs downwards 2 Extend the feet of the tripod stand as far as they will go for maximum stability and tighten the fixing clamp 3 Ideally the tripod should be placed on reasonably level ground so that the tripod is vertical use the ground anchor pegs to secure the tripod 4 Attach the LNB arm to the dish using the two wing nuts on the rear of the dish 5 Mount the dish on the tripod and use the compass to align one of the tripod legs so that it is in the azimuth direction indicated by the dish pointing table included with the kit 6 Rotate the dish so the LNB arm is pointing in the same d
4. engineer copy or manipulate the patent registered technology included with our products and any party who may breach these conditions set herewith will he subjected to legal action to the full extent of the law in his or hers jurisdiction All EZ Net products are covered by a 1 year warranty against any hardware defects ONLY Any damages or accidental breakages to have been caused ill th th f thi t The contents of this publication are believed to be correct at the time of going to press however any information Details products or services may be supplemented modified or withdrawn without notice Another innovative product from Falcon Technical Ltd Hill Farm Northwich Road Dutton Cheshire WA4 4LE Tel 01928 759 239 a amma 16
5. the tripod thumbwheel to lock the dish in position 12 Checking the Pointing Make sure you can still hear the continuous high pitch tone then briefly place your hand between the iLNB and the dish The tone will change but as soon as you remove your hand you need to hear the continuous high pitch tone again When the antenna is correctly pointed the message Correct satellite pointed optimally appears on the screen of your computer as shown below You can now proceed Overview Modem State antenna pointing Correct satellite pointed optimally 0 0 dB below maximum measured level When the antenna is not optimally pointed the message Correct satellite not pointed optimally is displayed instead Finishing the Pointing 1 Turn off the Point amp Play tool 2 Remove the TX cable from the Point amp Play tool and reconnect it to the iLNB 3 Back at your computer in the status page of the modem click Finish Pointing Antenna Pointing Finish Pointing Software Download The modem continuously checks for software updates If the software is up to date this step is skipped automatically if a newer software version is available download will start automatically Software Download Currently Running Software Version 2 2 4 19 Downloading version 2 2 6 15 9 complete Please wait t Once the download is complete the new software is installed automatically Software Download status Downloaded version 2 2 6 15 Wr
6. aler even if you dont purchase a new product Further collection facilities are listed on the homepage of www swico ch B Information on Disposal for Business Users 1 In the European Union If the product is for business users and you want to discard it Please contact your EZ Net dealer who will inform you about the take back of the product_ You might be charged for the costs arising from take back and recycling _ Small products and small amounts might be taken back by your local collection facilities 2 In other Countries outside the EU If you wish to discard this product please contact your local authorities and ask for the correct method of disposal The batteries supplied with this product contains traces of Lead For EU The crossed out wheelie bin implies that used batteries shouldnot be put to the general household waste There is a separate collection system for used batteries to allow proper treatement and recycling in accordance with legislation Please contact your local authority for details on the collection and recycling schemes For other non EU countries Please contact your local authority for correct method of disposal of the used battery WARRANTY DISCLAIMER EZ Net is a trademark of Falcon Technical Ltd All technology and techniques used to build and deliver our products are intellectual property of the above named company or its associated partners It is against copyright laws to attempt to extract reverse
7. e To proceed you need to access the web interface of the modem To do this you can connect a computer to the spare RJ45 network socket on the router or use WiFi Make sure the modem is turned on and properly connected to the WiFi router and that the router and power lights on both are on To use WiFi search for available WiFi networks and look for one named EZ NET and connect to this network There is no password by default Once connected to the WiFi start your internet browser Internet Explorer Chrome Mozilla Firefox Opera Safari etc on your computer Type 192 168 1 1 in the address bar of the browser and press Enter http 192 168 1 1 If this is the first time setting the system up the terminal installation page automatically opens CEE status Configuration Overview Modem State Error 001 Awaiting installer action Software Version 2 2 4 19 Terminal Installation est Outdoor Unit 2W_Ka_ ILB2210 _ _75cem_ ANT2010 Spot Beam w 22 Antenna Pointing Start Pointing Skip Pointing If you are setting the dish up again after having moved location Status page will open automatically instead select Terminal Installation in the left hand menu and then click the Restart button at the bottom to restart the complete installation procedure Pointing the dish Enable Pointing Mode on the Modem Click Start Pointing to start the pointing procedure and proceed to the next section Setting up the Point amp
8. irection and then tighten the thumbscrew 7 Once the dish is secured on the tripod it should look like the image FIG 3 Do not overtighten the thumbscrew at this point as rotation will be required for the final step in tuning Mounting the iLNB Mount the iLNB in the clamp and position so that the is vertical with the seam in the case in line with the dish arm as shown below Do not connect any leads until your satellite dish is firmly on the tripod Setting the Elevation Attach the magnetic base of the elevation meter to the black wedge on the arm of the dish and switch the meter on Use the dish pointing table included with the kit to look up the elevation angle that applies to your location or to the city closest to your location Pull the dish adjustment handle outwards to allow the elevation of the dish to be changed with the dish face starting at vertical slowly tilt the top of dish back until the correct elevation reads on the i elevation meter as shown on the right Release the dish adjustment handle so that it locks the dish in position Connecting the iLNB to the modem The twin coax cable is supplied with waterproof connectors on one end and standard connectors on the other end Make sure the waterproof connectors are used at the dish end Indoor Connectors Outdoor Connectors for modem for iLNB Connect the coax cable marked with the RED band to the socket marked TX on the iLNB and connect the coax cab
9. iting downloaded software to flash The modem reboots automatically Now you can proceed to the next step Validation of the Installation You may need to refresh the page of your browser manually after the reboot 13 Validation of the Installation Once pointing has been finished and the software updated if required the following screen is shown Terminal Installation Outdoor Unit v 2W_Ka_ ILB2210 _75cm_ ANT2010 Spot Beam v 22 Antenna Pointing v Software Download v 2 2 6 15 Validate Installation Finish Installation Once validation is complete the following screen is shown Menu Status Status Configuration Overview ethernet Interface Satellite Interface Modem State network layer initialization Soar Une Demodulator 32 4 dBm E No 4 8 dB Ka Astra2 Device Software Version 2 2 6 15 Terminal Installation Logfile sein cents Ec ayda Outdoor Unit 2W_ Ka _ ILB2210 75cm _ ANT2010 lest Spot Beam v 22 Antenna Pointing Software Download w 2 2 6 15 gt Installation Z Finish Restart Click Finish to go to the Status Page 14 The modem is now ready for operation and all LED indicators on the status page are green Ethernet G Satellite Software Configuration Overview Ethemet Interface Satellite Interface Modem State operational hie ite Demodulator 32 4 dBm E No 4 8 dB Ka Astra2 Device Software Version 2 2 6 15 Hardware Terminal Installa
10. le marked with the BLUE band to the other socket on the iLNB At the modem end connect the coax cable marked with the RED band to the socket marked TX iLNB on the modem and connect the coax cable marked with the BLUE band to the socket marked RX iLNB on the modem TO w C Ce r GG Aine um ms Dos LN BEET s lt Cable with BLUE band Cable with RED band The modem and router must be installed inside in a dry location The modem itself can be installed in three ways as illustrated in the picture below e Wall mounted Note screws for wall mount installation are not included e Horizontal e Vertical mounted on the included stand The WiFi router also has holes on the back allowing it to be wall mounted if required Connecting the WiFi Router to the modem Attach the antenna to the WiFi router and connect the red network cable from the LAN socket on the modem to the socket on the WiFi router that is next to the antenna Now connect the 240V mains power adapter to the modem Connect the 240V mains adapter to the WiFi Router P7 Modem Mains Adapter Router WiFi Adapter 24V output 12V output CAUTION Ensure correct adapter is used with each device If using 12 Volt power plus the mains adapters into the mains inverter connect the inverter input to your 12 Volt source observing the correct polarity and switch the inverter on Connecting to the modem web interfac
11. nnect to it 15 End of Life Disposal A Information on Disposal for Users private households 1 In the European Union Attention if you want to dispose of this equipment please do not use the ordinary dustbin Used electrical equipment must be treated separately and in accordance with legislation that requires proper treatment recovery and recycling of used electrical and electronic equipment Following the implementation by member states private households within the EU states may return their used electrical and electronic equipment to designated collection facilities free of charge In some countries your local retailer may also take back your old product free of charge if you purchase a similar new one Please contact your local authority for further details If your used electrical or electronic equipment has batteries or accumulators please dispose of these separately beforehand according to local requirennents_By disposing of this product correctly you will help ensure that the waste undergoes the necessary treatment recovery and recycling and thus prevent potential negative effects on the environment and human health which could otherwise arise due to inappropriate waste handling 2 In other Countries outside the EU If you wish to discard this product please contact your local authorities and ask for the correct method of disposal_ For Switzerland Used electrical or electronic equipment can be returned free of charge to the De
12. nting Keep the space between the iLNB and the antenna dish clear Using the Point amp Play Tool To use the Point amp Play tool 1 Remove the TX connector red band from the iLNB and connect it to the Point amp Play tool 2 Connect the earphone to the Point amp Play tool Make sure the Point amp Play tool is still switched off iu iu Vertical Pointing elevation The correct elevation angle was already set when setting up the dish You can use the elevation meter to verify that the elevation angle still corresponds to the value you have found in the dish pointing information and adjust if necessary Horizontal Pointing rotation azimuth Switch on the Point amp Play tool by slowly turning the volume wheel until the green LED illuminates Put on the earphone and adjust the volume if necessary Now the actual pointing procedure can start If the correct elevation and rotation have been set you should hear a high uninterrupted tone if this is not the case adjust the rotation of the dish until you hear the highest possible continuous pitch tone detection of the correct satellite Slowly move the dish left and right across the correct direction and listen for the tone to change Make sure you position the dish in the middle of the highest tone range If you don t hear a tone check that the battery is the Point amp Play tool is not dead Once you have the dish positioned with the high tone tighten up
13. tion Interface Statistics Logfile Diagnostic Report Interface J bytes packets errors dropped Test RX 72795 549 0 0 Ethernet Interface TX 205720 445 0 0 ee Rx 19214 85 o 0 atellite Interrace Tx 152 a 3 You are now ready to surf the internet Adding security to the WiFi router By default there is no security on the WiFi router you can add a password as follows 1 Make sure you are connected to the EZ NET WiFi network and type 192 168 2 1 in the address bar of the browser and press Enter 2 Login with the username admin and password admin 3 On the top menu select Advanced and then Security under Wireless settings 4 Inthe drop down menu for Security mode select WPA2 PSK and leave WPA Algorithm on Auto 5 Enter the password you want to use in the Pass Phrase box and click the blue Apply button You don t need to put anything in the Access Policy section Wireless Security and Encryption Settings The Wireless Security and Encryption Settings page allows you to make detailed security configurations to prevent unauthorized access and monli Select RANGEMASTER Security Mode WPA2 PSK N WPA WPA Algorithms TKIP AES Auto TKIP AES ee 8 63 ASCII or 64 Hexadecimal Key Renewal Interval 3600 seconds Access Policy my o ooo e Add a station MAC The router will restart and you will then have to use the password you set to co
Download Pdf Manuals
Related Search