User`s Manual
Contents
1. BPU 350SATA BPU 350SATA 3 5 Hard Drive Cage specification User s Manual Hotswap S SHDD O O Aluminum Design with Conductive Dissipation Grooves HDD Interface SATA SAS Weight tas yO SATA Cable Included 5pcs Order Information Model Number UPC Code BPU 350SATA BLACK Black 846813022606 BPU 350SATA RED Red 846813000604 BPU 350SATA BLUE Blue 846813000598 BPU 350SATA SILVER Silver 846813000611 BPU 350SATA BPL Plastic 846813016087 lockable handle iStarUSA Powered by iStarUSA Group 727 Phillips Drive City of Industry CA 91748 Tel 888 989 1189 Email sales istarusa com Introduction Hardware Information Front View Create more space for hard drive with hot swap capability by using the BPU 350SATA HDD cage series that supports RAID 1 0 1 0 5 configuration for high performing data recovery or redundancy application Its aluminum construction translates into lighter system weight and better heat dissipation The 80mm fan also help keeps hard drives at maximum performance temperature D 1 D 2 D 3 D 4 D 5 D 6 D 7 Features Aluminum Frame Aluminum cover Interface Support SAS I and SAS II SATA I SATA II SATA III High performance transfer rate up to 6 0 GB s for SAS amp SATA hard drives e Plug amp play hot swappable e SATA 15Pin amp 4Pin Power connectors LED for P S HDD access Fan sensor amp Buzzer Power Control Switch 3 stage temperature alarm2. RAID Configuration amp Setup procedure please follow the user manual instructions from your SAS SATA Controller Card or Motherboard Accessories e 5 SATA cables Screws Optional Accessories HD Trays Model Number UPC Code Black BPU HSTRAY BLACK Red BPU HSTRAY RED 846813000635 846813000659 846813000642 846813000673 846813000628 Blue BPU HSTRAY BLUE Silver BPU HSTRAY SILVER Plastic BPU HSTRAY iStarUSAcare We will help you navigate our website to find the information that you need Go to www istarusa com and click on live chat bubble above the Search Bar Our technicians are standing by to take your questions Visit http istarusa com support and you will receive a technical IEN support ticket to help track your requests from the beginning to the end Or you can contact us 888 989 1189 FCC and CE Radiation Norm FCC This equipment has been tested and found to comply with limits for Class B digital device pursuant to Part 15 of Federal Communications Commission FCC rules CE This equipment has been tested and found to comply with the limits of the European Council Directive on the approximation of the law of the member states relating to electromagnetic compatibility 89 336 EEC according to EN 55022 Class B FCC and CE Compliance Statement These limits are designed to provide reasonable protection against frequency interference in residential installation This equipment generates uses and
3. can radiate radio frequency energy and if not installed or used in accordance with the instructions may cause harmful interference to radio communication However there is no guarantee that interference will not occur in television reception which can be determined by turning the equipment off and on The user is encouraged to try and correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver connect the equipment into an outlet on a circuit different from that to which the receiver is connected to CAUTION The Federal Communications Commission warns the user that changes or modifications to the unit not expressly approved by the party responsible for the compliance could void the user s authority to operate the equipment BPU 350SATA
4. pin setting JP 1 a a wt s at s 2 5 or 3 5 Hard Drive Disk to the trays Installation 1 Insert 2 5 or 3 5 Hard Drive into the HDD Tray from the cage 2 Use the provided screws and fasten HD into highlighted 2 5 or 3 5 holes to the cage trays 3 Make sure Secure with screw holes from the Bottom of 2 5 or 3 5 Hard Drive s 4 After the screw installation slide the HDD Tray back to the HDD Canister Base 5 Next follow the Quick Installation in next page for the rest of the Setup 3 5 HD Screw Holes 2 5 HD Screw Holes HD Tray Bottom View 3 5 HD Screw Holes BPU 350ATA BPU 350SATA Quick Installation Procedure 1 Open up the handle bar from the tray take out the HD trays from the HD cage Secure all screws to the HD attached with HD tray Place the hard drive tray s with HD installed back into the cage unit Push the handling bar into closed position Connect all necessary data and power cable onto the rear end of cage unit Make sure that the date cables connected to the motherboard side as well 6 Turn onthe Power of your computer and wait until Operating System finish loading up 7 Turnon all necessary HD1 HD4 Power Button s for each Hard Drive installed ae y Note For steps 6 if the operating system installed with a HD inside of HD cage please make sure you do turn on the Power from the cage switches D1 D2 D3 D4 or D5 For optional
5. settings amp reset switch for buzzer alarm D 1 D 5 Power Switch amp HDD LED Power On LED indicates Blue Purple color blinking for HDD access D 6 Reset Switch amp Overheat LED Power On LED indicates Blue Overheat default 552 C LED indicate Red and buzzer alarms Press the Reset Switch D 6 to stop the alarm for 3 minutes e 8cm cooling fan X1 D 7 Fan senor LED Fan On LED indicates Blue Fan Off LED indicates Red and buzzer e Dim 8 11 L X 5 75 W X 4 96 H inch e Patent products with advanced structure design Patent balance handle No skew in out problem amp avoid the abrasion during connection e Precisely connection on connector alarms Press the Reset Switch D 6 to stop the alarm If you want to switch off the Alarm function press the Reset Switch D 6 for more than 6 seconds until 3 beeps comes out then the Alarm function stopped BPU 350SATA BPU 350SATA BPU 350SATA Hardware Information Rear View Power Pow et 2 15 j HDI HDS POWER1 4pin Power connector POWER2 15pin Serial ATA Power connector may use any two type of power connector HD1 HDS 7pin Serial ATA Signal connector JP1 Temperature setting jumper default 552 C J5 FAN RPM Switch HIGH amp AUTO Optional Every time when you turn on the power the fan runs for 10 seconds and then stop It will run again when temperature reaches 402 C J6 HD LED Switch default Enable JP1 Jumper
Download Pdf Manuals
Related Search