Networking your Wholehog 3 to your Visualizer computer
Contents
1. 1 Crossover ethernet cable cat 5 Wholehog Visualizer Connectivity Drivers on your Computer Visualizer Program ESP Vision Wyg MSD Capture Use custom address range Address Range Start 172 31 192 0 Address Range End 172 31 255 254 One network option and probably the easiest is to set your console to act as a DHCP server That means that your console can distribute all of the TCP IP settings needed for a successful network connection to your visualizer computer Important Ensure that you are running Wholehog software Version 3 0 or greater Note This document is specifically for connecting to a dedicated ESP Vision visualizer computer If you are using a different visualizer then the instructions in Part 3 will not apply However Parts 1 and 2 will be useful in setting up your console with your visualizer computer Part 1 Configuring your console s network settings 1 Press the SETUP key and select CONTROL PANEL from your main toolbar This can also be accessed from the Start menu 2 In the Control Panel select the NETWORK tab 3 Ensure that the settings are at as listed below Your HogNet Adaptor should list your console s or computer s Ethernet port Select Use default IP settings Under DHCP Boot Server Enable DHCP and Boot Server will need to be selected 4 Press OK contol Panel v3 00 b 2417 Network Lal sada HogNet Adapter DHCP Boot Server anes Keyboa2. 2 In the Control Panel select the NETWORK tab 3 From the drop down menu your HogNet Adaptor should list your console s Ethernet port this especially important to setup correctly when using Hog3PC on a computer with multiple network adaptors 4 Select Use Default IP settings 5 Under DHCP Boot Server select Enable Boot Server only 6 Press OK 6 Connecting a Wholehog console with your Visualizer computer 2009 Cat West High End Systems Your Control Panel should look something like this Panett v3 0 0 Db Z24171 s Network HogNet Adapter DHCP Boot Server Intel R PRO Network Connection wv Enable DHCP and Boot Server 00 19 d2 4 eat bs ress i KY Enable Boot Server only Link State Up Link Speed 54Mbps Rx Packets 84382 Tx Packets 53988 Use custom address range Rx Errors 0 Tx Errors 0 Rx Drops 0 Tx Drops 0 Address Range Start 172 31 128 1 Use defaut IP settings Address Range End 172 31 191 255 Obtain an IP address using DHCP Use custom P settings IP Address 172 31 0 1 Gateway 172 31 0 1 Netmask 255 255 0 0 DNS 1270 0 1 S w oK x cae Part 3 Launching the Visualizer This section uses ESP Vision as the example If you are using a visualizer that is not ESP Vision consult your Visualizer s manual for launching instructions specific to your visualizer 1 Log i
3. Description Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks C Show icon in notification area when connected Notify me when this connection has limited or no connectivity 6 Another window will open select Obtain an IP Address Automatically and also Obtain DNS address automatically It should look like the screenshot below internet Protocol TCP IP Properties ix pmm v General Altemate Configuration You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address Obtain DNS server address automatically Use the following ONS server addresses 3 Connecting a Wholehog console with your Visualizer computer 2009 Cat West High End Systems 7 Click OK and close all network windows Note You may see an information message on your computer that says you have Limited or No Connectivity to the internet This is not an error the Wholehog 3 will not give you access to the internet Part 3 Launching the Visualizer This section uses ESP Vision as the example If you are not using ESP Vision consult your Visualizer s manual for launching instructions 1 Log into your patched sho
4. If you are using a different visualizer then the instructions in Part 3 will not apply However Parts 1 and 2 will be useful in setting up your console with your visualizer computer Part 1 Configuring your console s network settings 1 Press the SETUP key and select CONTROL PANEL from your main toolbar This can also be accessed from the Start menu 2 In the Control Panel select the NETWORK tab 3 From the drop down menu under Adaptor Configuration the adaptor should be configured for your console s or computer s Ethernet port 4 Select Obtain an IP address using DHCP 5 Under DHCP Boot Server ensure that Enable DHCP and Boot Server is not selected 6 Press OK Control Panel v3 0 0 b 24174 HogNet Adapter 5 DHCP Boot Server Intel R PRO Network Connection v Enable DHCP and Boot Server MAC 00 19 d2 Link State Up Link Speed 54Mbps Rx Packets 84375 Tx Packets 53981 FE Rx Enors 0 Tx Brors 0 Rx Drops 0 Tx Drops 0 Address Range Start o 0 0 0 Use defaut IP settings Address Range End 255 255 255 255 gee ae rai os Enable Boot Server only KY Obtain an IP address using DHCP Use custom P settings 9 Connecting a Wholehog console with your Visualizer computer 2009 Cat West High End Systems Part 2 Configuring your Visualizer Computer 1 Click your computer s START Button and select My Network Places 2 In th
5. Description Transmission Control Protocol Internet Protocol The default wide area network protocol that provides communication across diverse interconnected networks C Show icon in notification area when connected Notify me when this connection has limited or no connectivity 5 Connecting a Wholehog console with your Visualizer computer 2009 Cat West High End Systems 6 Another window will open select Use the following IP address with these settings IP Address 172 31 0 2 Subnet Mask 255 255 0 0 Default Gateway 172 31 0 2 It should look like the screenshot below Internet Protocol TCP IP Properties General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings C Obtain an IP address automaticall Use the following IP address IP address Subnet mask Default gateway Use the following DNS server addresses Preferred DNS server Altemate DNS server 7 Click OK and close all network windows Note You may see an information message on your computer that says you have Limited or No Connectivity to the internet This is not an error the console will not give you access to the internet Part 2 Configuring your console s network settings 1 Press the SETUP key and select CONTROL PANEL from your main toolbar This can also be accessed from the Start menu
6. High End Systems Inc Networking your Wholehog to your Visualizer computer A guide to establishing a network connection with Wholehog 3 Hog iPC Roadhog Full Boar and Hog3PC This document is intended as an addition to the Visualizer Connectivity Application Instructions which can be found online and in the Wholehog User Manual DHCP Boot Server iy Enable DHCP and Boot Server Page 2 Instructions for connecting via your console s internal DHCP Server Enable Boot Server only Use custom address range Address Range Start 172 3 Address Range End Network HogNet Adapter Intel R PRO Network Connection MAC 00 19 d2 4 Page 5 Link State Up Link Speed Px Packets 84382 Tx Packets Instructions for manually configuring your Rx Errors 0 Tx Errors 0 tesa i caret network settings between console and Visualizer ny Use default IP settings l Obtain an IP address using DHCP Use custom IP settings IP Address 172 31 0 1 1 Netmask 255 255 0 0 Use default IP settings Page 9 Instructions for Networking your console to your Visualizer via a Router KY Obtain an IP address using DHCP Use custom IP settings Cat West High End Systems Updated 2 9 2009 DHCP Boot Server Setting your console as a DHCP server to Enable DHCP and Boot Server network with your Visualizer computer Enable Boot Server only What you ll need in addition to the console
7. e new window click View Network Connections from the left pane under Network Tasks Alternatively open your computer s Control Panel and select Network Connections 3 Locate your Local Area Connection and right click on it 4 From the drop down menu select Properties 5 In the new window that opens select Internet Protocol TCP IP and click Properties See screenshot below Local Area Connection Properties General Advanced _ Connect using B9 Intel R PRO 100 VE Network Conne IPEER This connection uses the following items Client for Microsoft Networks CI inter Sharing for Microsoft Networks E Y Intemet Protocol TCP IP Description Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks C Show icon in notification area when connected Notify me when this connection has limited or no connectivity 6 Another window will open select Obtain an IP Address Automatically and also Obtain DNS address automatically It should look like the screenshot below pmm v General Altemate Configuration internet Protocol TCP IP Properties ix You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically U
8. nto your patched showfile on your console before starting your Visualizer 2 After launching ESP Vision choose Hog 3 as your DMX source DMX Source x Please select your DMX source Lok cae 3 The visualizer will then launch along with your connectivity driver You can see the status of your connection in the Wholehog DP window The process will look like these screenshots below S Wholehog DP Status Apply Status Locating Wholehog Network eee Session Locos Info Connecting on port 6600 Configuration Port 6600 User Number 1 ae 2 21 7 Connecting a Wholehog console with your Visualizer computer 2009 Cat West High End Systems Connecting a Wholehog console with your Visualizer computer 2009 Cat West High End Systems Networking your Wholehog to your a Visualizer using a Router Obtain an IP address using DHCP oe ad i What you ll need in addition to the console Q wowose Ct 2 Non crossover patch Ethernet cables Wholehog Visualizer Connectivity Drivers on your Computer Visualizer Program ESP Vision Wyg MSD Capture Placing a pre configured router in the network between your console and your visualizer computer will allow the router to set compatible TCP IP settings Important Ensure that you are running Wholehog software Version 3 0 or greater Note This document is specifically for connecting to a dedicated ESP Vision visualizer computer
9. rd Intel R PRO Network Connection WwW KY Enable DHCP and Boot Server Wings MAC 00 13 42 00 a Enable Boot Server only Link State Up Link Speed 54Mbps mb MIDI Rx Packets 84434 Tx Packets 54102 Fi Use custom address range Tx Erors 0 Rx Errors 0 Time and Date 2 S Rx Drops 0 Tx Drops 0 Address Range Start 1 72 31 1920 m Auto Launch Use defaut IP settings Address Range End 172 31 255 254 a Obtain an IP address using DHCP System Info Use custom IP settings 2 Connecting a Wholehog console with your Visualizer computer 2009 Cat West High End Systems Part 2 Configuring your Visualizer Computer 1 Click your computer s START Button and select My Network Places 2 In the new window click View Network Connections from the left pane under Network Tasks Alternatively open your computer s Control Panel and select Network Connections 3 Locate your Local Area Connection and right click on it 4 From the drop down menu select Properties 5 In the new window that opens select Internet Protocol TCP IP and click Properties See screenshot below Local Area Connection Properties General Advanced _ Connect using B9 Intel R PRO 100 VE Network Conne IPEER This connection uses the following items Client for Microsoft Networks CI inter Sharing for Microsoft Networks E Y Intemet Protocol TCP IP
10. rt 6600 Pot 6600S User Number User Number mn 2 21 2 21 11 Connecting a Wholehog console with your Visualizer computer 2009 Cat West High End Systems Note 1 The original Roadhog does not have networking capabilities as the Full Boar does In order to communicate with a Visualizer you will need a DMX to USB device Consult your visualizer manufacturer for more information regarding this Note 2 When connecting a Full Boar console to a visualizer computer please use the Hog Net Ethernet port Note 3 If you want to run Hog3PC and your Visualizer on the same computer no networking will be necessary Keep in mind that HES FPS does not recommend running both Hog3PC and ESP Vision or other visualizer on the same computer These programs can be processor heavy so HES FPS cannot guarantee the stability of either system if both are run simultaneously on the same computer 12 Connecting a Wholehog console with your Visualizer computer 2009 Cat West High End Systems
11. se the following IP address Obtain DNS server address automatically Use the following ONS server addresses 10 Connecting a Wholehog console with your Visualizer computer 2009 Cat West High End Systems 7 Click OK and close all network windows Note You may see an information message on your computer that says you have Limited or No Connectivity to the internet This is not an error the Wholehog 3 will not give you access to the internet Part 3 Launching the Visualizer This section uses ESP Vision as the example If you are not using ESP Vision consult your Visualizer s manual for launching instructions 1 Log into your patched showfile on your console before starting your Visualizer 2 After launching ESP Vision choose Hog 3 as your DMX source UMA Source Please select your DMX source Hog 3 p 3 The visualizer will then launch along with your connectivity driver You can see the status of your connection in the Wholehog DP window The process will look like these screenshots below S W n 0O n O E f p x Status we Apply Status Locating Wholehog Network Session Info Connecting on port 6600 Configuration pot 6500S User Number 1 ly 2 21 Wholehog DP 1932 x S Wholehog DP 1932 x Status Apply Status Spp Status Loading Show ciae Runin PPP g Info Loading Fisture Data Info Outputs Active Configuration Configuration Po
12. ure Q wonm eaissooe These instructions will help you to manually configure compatible Q momona TCP IP ranges on both your console and your Visualizer IP Address 172 31 0 computer The example below shows you one possible 255 255 0 0 compatible configuration but you may choose to use a different range Important Ensure that you are running Wholehog software Version 3 0 or greater Note This document is specifically for connecting to a dedicated ESP Vision visualizer computer If you are using a different visualizer then the instructions in Part 3 will not apply However Parts 1 and 2 will be useful in setting up your console with your visualizer computer Part 1 Configuring your Visualizer Computer 1 Click your computer s START Button and select My Network Places 2 In the new window click View Network Connections from the left pane under Network Tasks Alternatively open your computer s Control Panel and select Network Connections 3 Locate your Local Area Connection and right click on it 4 From the drop down menu select Properties 5 In the new window that opens select Internet Protocol TCP IP and click Properties See screenshot below Local Area Connection Properties General Advanced Connect using E9 Intel R PRO 100 VE Network Conne This connection uses the following items M E Client for Microsoft Networks iw e ang re nA i v aA Intemet Protocol TCP AP
13. wfile on your console before starting your Visualizer 2 After launching ESP Vision choose Hog 3 as your DMX source ic ws DM Croerre K UMA S0Urce Please select your DMX source Hog 3 p oma 3 The visualizer will then launch along with your connectivity driver You can see the status of your connection in the Wholehog DP window The process will look like these screenshots below S W no n og f p Ee Status we Apply Status Locating Wholehog Network Session Info Connecting on port 6600 Configuration Port 6600 E User Number 1 2 21 Wiotehog DP 1937 El SWIET x Status Apply Status TE Status Loading Show Shane Hunan PPP g Session Connected Session Connected Info Loading Fixture Data Info Outputs Active Configuration Configuration Port 8600 Port 6600 User Number User Number 1 sal 2 21 v2 21 4 Connecting a Wholehog console with your Visualizer computer 2009 Cat West High End Systems Manually Configuring your network settings between your Wholehog and Waa your Visualizer computer HogNet Adapter Intel R PRO Network Connection Yv Mac 0019424 What you ll need in addition to the console Link State Up Link Speed 54Mbps Fi Packets BEERS eee 1 Crossover ethernet cable cat 5 Rx Brors 0 Tx Bors 0 Wholehog Visualizer Connectivity Drivers on your Computer Rx Drops 0 Tx Drops eas g suazer Program ESP Vision Wyg MSD Capt
Download Pdf Manuals
Related Search