SAT-201 User Manual
Contents
1. Pin Function Cable colour code if supplied by Satamatics 1 OV cable screen Screen 2 Voltage In VIN Red 3 OV VIN Orange 4 OUT2 Yellow 5 OUT Green 6 IN2 Blue 7 INI Purple 8 Rx Grey 9 Tx White 10 OV VIN Black 11 Rx GPS Brown 12 Tx GPS Pink 11 2 Interface functions VIN VIN Tx Rx Tx GPS Rx GPS INA OUTn Satamatics Ltd External power input 9 6V to 32V RS232 serial control data interface transmit Tx and receive Rx lines o 9600bps asynchronous optional parity o Control function for configuring the unit o Data function for message input output RS232 serial GPS test interface transmit Tx and receive Rx lines 38400bps asynchronous optional parity Used for software download Not available during normal operation 2 off inputs individually configurable as o Digital input 32V maximum with falling edge interrupt capability o Switch input internal pull up used with external switch to ground with falling edge interrupt capability o SAT 101 compatible digital input low voltage with falling edge interrupt capability o Analog input 12 bit ADC 0 to 2 5V o SAT 101 compatible digital output low voltage 2 off digital open drain outputs 250mA max sink current suitable for driving relays indicators etc Page 17 of 22 KOsatamatics SAT 201 User Manual MAN 0019 Issue 2 11 3 General Purpose I O Figure 5 shows a conceptual drawing of one of t2. Safety Warnings U D U No user serviceable parts inside Refer servicing to qualified service personnel The equipment contains no replaceable fuses Retain the safety and operating instructions for future reference Observe all warnings on the equipment and in the operating instructions Follow all operating and user instructions Connect the equipment to a power supply only of the type described in the operating instructions or marked on the equipment The unit should be located away from power lines Maximum permissible exposure MPE limits This equipment complies with FCC OET bulletin 65 general population uncontrolled exposure limits as applied to RF energy from a Mobile device A mobile device being defined as a transmitting device designed to be used in other than fixed locations and to be generally used in such a way that a separation distance of at least 20 centimetres is normally maintained between the transmitter s radiating structures and the body of the user or nearby persons Satamatics Ltd Page 5 of 22 KOsatamatics SAT 201 User Manual MAN 0019 Issue 2 3 REGULATORY AND TYPE APPROVAL INFORMATION 3 1 European Compliance The equipment is designed tested and declared to conform to the following European directives and standards 1999 5 EC CE mark R amp TTE includes directives 89 336 EEC EMC and 73 23 EEC LVD Relevant Standards EN301 489 20 v1 2 1 2002 11 EMC Testin
3. position it then identifies the best Ocean Region to use and proceeds through the sequence of states referred to in Section 12 If for some reason the unit is not able to obtain a valid GPS reading after two minutes it will follow the sequence using the default Ocean Region AORE If you wish to check the overall system operation it will be necessary to ensure that the terminal is activated on a known gateway and that you have access to the application running there so that you can view the received data If you do not have access to an application of your own it is possible to set up your terminal on one of the Satamatics websites in order to perform end to end testing Please consult your service provider for details of the activation that has been put in place for your terminal If you do not have access to the application it is still possible to check the local operation of the terminal and its installation by using the following sequence In this case it will then be necessary to check the application part of the system later With the SAT 201 in position apply power to the unit and monitor the indicator Initially it will either be off or will be in the D off state and will then cycle through the following states RED OFF OFF OFF D Off RED OFF GREEN OFF Acquiring Bulletin Board GREEN GREEN RED RED Demodulating Bulletin Board GREEN ORANGE GREEN OFF Acquiring Traffic Channel Once it has acquired th
4. K satamatics SAT 201 User Manual Document No MAN 0019 Issue No 2 Dated 16 June 2005 KOsatamatics SAT 201 User Manual MAN 0019 Issue 2 COPYRIGHT Copyright in this document is vested in Satamatics Ltd This document is issued in confidence for the purpose only for which it is supplied It must not be reproduced in whole or in part except with the consent in writing of Satamatics Ltd and then only on the condition that this notice is included in any such reproduction Revision History Date Issue Comments 19 April 2005 1 Initial Issue 3 1 Minor changes to European Compliance Statement 16 June 2005 2 11 3 Included warning regarding lO devices default state 14 Minor Change to Product Information Page 2 of 22 Satamatics Ltd KCsatamatics MAN 0019 Issue 2 SAT 201 User Manual CONTENTS 1 LEGAL INFORMATION aaa AKWA ANAWAKA aaa WAKIWA NAA kak AAAA ARAARA 4 LI NOtUCS gt gt gt gt eepemmzZanz zmmmm aces ees 4 1 2 Limited Wanane ee ai eee a hee ed ae ie 4 VE E Baelen ln LTE A TA 2Goverming ET 4 2 SAFETY WARNINGS wanaamini aaa waa kk RAKR Kak KAKA AR RRA AA KA KK aaa Kawa Nawawi 5 2 1 EE CHEN A Ee E 5 3 REGULATORY AND TYPE APPROVAL INFORMATION cc eceeessseeeeeseseeeeessseeeeenseseeees 6 3 1 European Compliance ssssssseniteneseeetttttttetttttt tnte ttrt tttE EEEN EAS EEEE EEEEEE ESSE EEEEEEER EESE E EEEE ES EESE EEEE 6 3 2 FCC Autorisation 6 3 3 IN
5. LE UNDER ANY CONTRACT NEGLIGENCE STRICT LIABILITY OR OTHER LEGAL OR EQUITABLE THEORY FOR ANY LOSS OF USE OF THE PRODUCT INCONVENIENCE OR DAMAGES OF ANY CHARACTER WHETHER DIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL INCLUDING BUT NOT LIMITED TO DAMAGES FOR LOSS OF GOODWILL WORK STOPPAGE COMPUTER FAILURE OR MALFUNCTION LOSS OF INFORMATION OR DATA CONTAINED IN STORED ON OR INTEGRATED WITH ANY PRODUCT RETURNED TO SATAMATICS LTD FOR WARRANTY REPAIR RESULTING FROM THE USE OF THE PRODUCT RELATING TO WARRANTY SERVICE OR ARISING OUT OF ANY BREACH OF THIS LIMITED WARRANTY EVEN IF SATAMATICS LTD HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES THE SOLE REMEDY FOR A BREACH OF THE FOREGOING LIMITED WARRANTY IS REPAIR OR REPLACEMENT OF THE DEFECTIVE OR NON CONFORMING PRODUCT 1 4 Governing Law The laws of England and Wales shall govern this one 1 year warranty Some countries do not allow the exclusion or limitation of incidental or consequential damages or exclusions or limitations on the duration of implied warranties or conditions The above limitations may not therefore apply to you This warranty gives you specific legal rights and you may also have rights that vary by country Page 4 of 22 Satamatics Lid KCsatamatics MAN 0019 Issue 2 SAT 201 User Manual 2 SAFETY WARNINGS AN BEFORE APPLYING POWER TO THE EQUIPMENT the user must read all instructions RJ If in any doubt consult suitably trained service personnel 2 1 General
6. Ltd Page 3 of 22 KOsatamatics SAT 201 User Manual MAN 0019 Issue 2 1 LEGAL INFORMATION 1 1 Notice Information in this document is subject to change without notice Satamatics Ltd makes no warranty of any kind with regards to this material including but not limited to the implied warranties of merchantability and fitness for purpose Satamatics Ltd shall not be liable for errors contained herein or for incidental or consequential damages in connection with the use of this material No part of this document may be photocopied reproduced or translated to another language without prior written consent of Satamatics Ltd The Satamatics logo is a registered trademark of Satamatics Ltd All other trademarks belong to their respective proprietors 1 2 Limited Warranty Satamatics warrants that the SAT 201 product will be free from defects in material and workmanship for a period of one 1 year from date of purchase During the warranty period Satamatics Ltd will at its option either repair or replace products that prove to be defective If a defect exists at its option Satamatics Ltd will repair the product at no charge using new or refurbished replacement parts or exchange the product with a product that is new or which has been manufactured from new or serviceable used parts and is at least functionally equivalent to the original product A replacement product assumes the remaining warranty of the original product or 90 days whichever is th
7. MARSAT Type Approval kk kk k k kk k kek kk ka k KEK KE KE KA KA KA KA KA KA KA KAK KA 6 3 4 Limitations on intended operating environment EEE kk k kk kk k 6 SAT 201 GENERAL DESCRIPTION uana AAA AAA AAA AAA KAKAA WAKAKA deg 7 INSTALLA TION eege eege ees Ee Edge dees 8 5 1 POWemREQUIFSINGINS yk y al n ketin kak Wan l ENEE AER Ee Sg 8 92 AA UA AAA AUNA MAA KAA AOA DIA NA 8 Did Location a a a a aea a aaa aaa a a aaa 9 SA MOUNN E 10 D D AP e EE 12 5 6 Operational Check EE 12 6 FUNCTIONALITY SE 13 7 MODES OF OPERATION 4 i annaa annan nA axak kk GENEE Wek waanikwa 13 8 FACTORY DEFAULTS eeh 13 9 MAINTENANCE AND SUPPORT INFORMATION 2 cccceseeeceeeseeeeeenseeeeeeesnaeeeenseaeseeeesnaes 14 01 CIGAMING n kya WAA aan dete at eaten ea dake ka kaw nn EE 14 9 2 Technical Support and Information 14 10 SPECIFICATIONS E 15 11 INTERFACES E 17 11 1 Interface Connector Pinot 17 11 2 Interface LA Pa Ya lel teuer 17 11 3 General Purpose yy mmn e o og ogg 18 12 INTERPRETING THE INDICATOR uuukkkknkkkkkkkkk kk kk KAK KK KAK KK KARA KK K KA AK KK KA AK KK KA RR KK KIRAR KK KA ARK 19 13 APPENDIX eebe keyl a k dek xi kk kak r ekl EEN EEN 20 13 1 CE Declaration of Conformity 0 00 0 cece kk wama kk kk kk k ka KA KA KA KA KAKA KA KAKA KA 20 14 Product INFOMATION cee ce eeeeee cece eee ee ee neice eee ne AKA eae nnee kaka kaka kaka AE KAWA KAKA WARA KA WARA WA WARA WAA HAAA eee 21 Satamatics
8. Page 14 of 22 Satamatics Ltd Ksatamatics MAN 0019 Issue 2 10 SPECIFICATIONS Physical Dimensions Weight Colour Connector Environmental Temperature Humidity Vibration Shock survival Ingress Protection Rating Freguency Range Transmit Receive GPS Elevation Angle Range Transmitter EIRP Modulation Tx burst duration User data rate Message length Receiver G T Modulation User data rate Message length Channels Time To First Fix Typical Cold start Hot start Accuracy SA Off Position CEP 2D Altitude Dynamic capability Velocity Acceleration Maximum update rate Satamatics Ltd SAT 201 User Manual 112mm diam x 45 75mm height Does not include mounting threads extensions 350g UN0332 Coconut 12 way plug Bulgin 400 Series Buccaneer compatible 40 C to 70 C lt 95 40 C 5 20Hz 1 92m s random noise 20 500Hz 3dB octave random noise Half sine 6ms 300ms IP66 when interface connector is correctly mated 1626 5 MHz to 1660 5 MHz 1525 0 MHz to 1559 0 MHz 1575 42 1 0 MHz 0 to 90 0 9dBW 2 level FSK 256Hz tone spacing 8s Global Beam 10 bits per second Global beam Up to 84 bits per burst 2 25dB K at EL 30 32 ary FSK 20Hz tone spacing 9 bits per second Up to 1000 bits 12 45s lt 8s GPS was off for less than 2 hours 4m Typical maximum 18000m maximum 515m s lt 4g 1s Page 15 of 22 SAT 201 Use
9. acquires the Bulletin Board and subsequently the Traffic Channel From power on to demodulating the Traffic Channel may take up to 7 minutes NOTE The indicator can be disabled off state or enabled via script control The indicator may therefore not come on when power is applied Contact your authorised dealer for details of any script that may have been programmed into the SAT 201 Satamatics Ltd Page 19 of 22 KCsatamatics SAT 201 User Manual MAN 0019 Issue 2 13 APPENDIX A 13 1 CE Declaration of Conformity Declaration of Conformity Manufacturer SATAMATICS Ltd Gloucester Road Tewkesbury Glos GL20 STT UK Product Identification Product description Inmarsat D Mobile Earth Terminal MET Model number SAT 201 The product is in conformity with the following directives and associated amending directives based on test results using harmonised standards R amp TTE Directive 1999 5 EC including o Low Voltage Directive 73 23 EEC o EMC directive 89 336 EEC Automotive Directive 95 54 EC Harmonised Standards Used Radio standards per Article 3 2 ETSI EN 301 426 v1 2 1 EMC standards per Article 3 1b ETSI EN 301 489 20 v1 2 1 ETSI EN 301 489 1 v1 4 1 Safety standards per Article 3 1a EN 60950 1 2001 Additional Information Technical file held by SATAMATICS Ltd Gloucester Road Tewkesbury Glos GL20 STT UK We SATAMATICS hereby declare under our sole responsibility that the equipm
10. d void the user s authority to operate this equipment Page 6 of 22 Satamatics Ltd Kcsatamatics MAN 0019 Issue 2 SAT 201 User Manual 4 SAT 201 GENERAL DESCRIPTION The SAT 201 is a compact single unit low data rate satellite terminal designed to operate over the INMARSAT satellites using the INMARSAT D protocol With an integral GPS receiver the SAT 201 provides low cost satellite communications for applications such as asset tracking telematics and SCADA exception reporting If you do not need battery backup solar panel power inputs or 4 20mA analogue output drivers then this is the solution for you Four INMARSAT satellites provide Global Coverage with each satellite covering an Ocean Region IOR AOR E AOR W or POR On power on or waking up a terminal first tunes to the Bulletin Board channel which contains information on the traffic channels currently in use From the traffic channel service ID mapping posted on the Bulletin Board the terminal determines on which traffic channel to expect its messages and re tunes to this channel Data rate for the forward channel to terminal is approximately 9 user bits per second with typical message delivery latency of about 3 minutes Return channel from terminal information is returned in bursts containing up to 80 user bits of information The data rate is approximately 10 user bits per second with typical message delivery latency of about 30s assuming the termi
11. e checked IDLE In certain circumstances the terminal will enter IDLE mode For example where GPS is not required and the current Traffic Channel frame contains no forward messages addressed to the unit GPS ONLY Similar to IDLE mode except that GPS is active enabling the terminal to monitor its position and compare for example against a Geofence STATIC Normal D operation where the terminal cycles between RECEIVE IDLE and TRANSMIT as appropriate GPS is not enabled MOBILE Similar to STATIC mode except that GPS is also enabled 8 FACTORY DEFAULTS The terminal is shipped with Factory Defaults set When power is initially applied the script timer alarm and operation definitions are cleared the terminal then powers up acquires the GPS position and tunes to the best ocean region for the terminal location Once the terminal has acquired the D satellite signal it transmits a single position report burst Satamatics Ltd Page 13 of 22 KOsatamatics SAT 201 User Manual MAN 0019 Issue 2 9 MAINTENANCE AND SUPPORT INFORMATION 9 1 Cleaning Dust and finger marks can be removed using a soft damp cloth Avoid using domestic cleaning products 9 2 Technical Support and Information For technical support product queries and information please contact your equipment supplier or authorised dealer Authorised dealers and general information about Satamatics products and services can be found at http Awww satamatics com
12. e longer for you All Hardware or part thereof that is replaced by Satamatics Ltd shall become the property of Satamatics Ltd upon replacement Satamatics does not warrant that the operation of the equipment or firmware will be uninterrupted or error free For warranty service or repair the product must be returned to a service facility designated by Satamatics Ltd quoting the information contained in Section 14 Failure to do so could invalidate or delay any warranty repair 1 3 Limitation of Warranty The foregoing warranty shall not apply to defects resulting from improper or inadequate maintenance by the Buyer Buyer supplied software scripts or interfacing unauthorized modification or misuse operation outside of the environmental specifications for the product or improper installation EXCEPT FOR THE ONE 1 YEAR LIMITED WARRANTY SPECIFIED HEREIN THE PRODUCT IS PROVIDED AS IS WITHOUT ANY WARRANTY OF ANY KIND INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND NON INFRINGEMENT If ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD THE DURATION OF SUCH IMPLIED WARRANTY SHALL BE LIMITED TO NINETY 90 DAYS EXCEPT AS EXPRESSLY COVERED UNDER THE LIMITED WARRANTY PROVIDED HEREIN THE ENTIRE RISK AS TO THE QUALITY SELECTION AND PERFORMANCE OF THE PRODUCT IS WITH THE PURCHASER OF THE PRODUCT TO THE MAXIMUM EXTENT PERMITTED BY LAW SATAMATICS LTD IS NOT LIAB
13. e traffic channel the unit will cycle through the following two states in normal operation GREEN GREEN GREEN OFF Demodulating Traffic Channel GREEN OFF OFF OFF Idle part of TC Frame The terminal will transmit its initial report LED turns orange for ten seconds after successfully completing the above states The total process to transmission will normally take between three and six minutes Providing that your terminal has been activated and set up within an application the data will be available within about one minute of the actual transmission although this is dependent on the operation of the software being used by your service provider as well as the link to the Satamatics server Your service provider will be able to supply you with further details regarding the normal use of the terminal as well as scripts and forward channel use A IMPORTANT The foregoing only applies to terminals that are set at Factory Default and with the default script installed see Section 8 If you are unsure about the state IL of your terminal you should consult your service provider Page 12 of 22 Satamatics Ltd KCsatamatics MAN 0019 Issue 2 SAT 201 User Manual 6 FUNCTIONALITY For full functional details on the SAT 201 contact your authorised dealer 7 MODES OF OPERATION SLEEP Extremely low power mode D and GPS functions are switched off IDLE mode is entered periodically so that external voltage can b
14. ent identified above complies with all the essential requirements of the directives Signed Title J Hatherall Engineering Director Satamatics Ltd i AWIR Z Page 20 of 22 Satamatics Ltd KCsatamatics MAN 0019 Issue 2 SAT 201 User Manual 14 PRODUCT INFORMATION It is essential that the following information be completed at the time of installation purchase to ensure that any future warranty claims are dealt with as expeditiously as possible DATE OF PURCHASE PURCHASED FROM SAT 201 ISN DISTO O 2 SAT 201 SERIAL NUMBER IMPORTANT PLEASE KEEP IN A SAFE PLACE FOR FUTURE REFERENCE NOTES Dealer Satamatics Ltd Page 21 of 22 Satamatics Ltd Corporate Head Office Tel 44 0 1684 278610 Fax 44 0 1684 278611 info satamatics com www satamatics com Satamatics USA Tel 1 877 SAT MATD Tel 1 877 728 6283 info satamaticsSUSA com www satamaticsUSA com
15. g EN 60950 1 2001 Electrical Safety R amp TTE ETSI EN 301 426 v1 2 1 2001 10 Radio Approval ETSI EN 301 489 1 v1 4 1 The Declaration of Conformity can be found at APPENDIX A 3 2 FCC Authorisation The following information is provided on the device covered in this document in compliance with FCC regulations Q Model number SAT 201 Company Name Satamatics Ltd Gloucester Road Tewkesbury GL20 5TT UK Also see MPE statement in Section 2 1 3 3 INMARSAT Type Approval The SAT 201 has been certified for operation on the Inmarsat Network Inmarsat Certificate Number DST002 3 4 Limitations on intended operating environment The SAT 201 can be used in a wide range of control and monitoring applications When third party equipment is attached such third party equipment and all cabling must be of suitable design and installation to ensure that the overall system complies with the requirements of the appropriate CE directives Guidance notes for the installation and use of the SAT 201 must be strictly followed Satamatics exercise due diligence to ensure that the equipment is suitable for use in stated applications but ultimate responsibility for the compliance of a complete system must rest with the prime contractor at a site where local conditions may require additional EMC precautions be taken WARNING Changes or modifications to this unit not expressly approved by the party Wi responsible for compliance coul
16. h The further away from the Equator the SAT 201 is the lower the degree of elevation will be above the horizon If you plan to install the SAT 201 in a partially enclosed environment test operation before committing to a permanent installation On vehicles the SAT 201 should be located on the highest point possible free from obstructions and safe from damage during normal operation of the host vehicle For installations exposed to shock and or vibration use a mounting scheme that isolates the unit from the excessive shock and or vibration Choose a location that is not near radar installations other satellite communication equipment and or microwave dishes to prevent RF jamming Avoid mounting on hot surfaces Satamatics Ltd Page 9 of 22 KOsatamatics SAT 201 User Manual MAN 0019 Issue 2 5 4 Mounting n If possible try the installation before drilling any holes or fixing cable Record the ISN number of the unit for future reference Q The SAT 201 may be mounted by utilising either the three outer M4 mounting holes Figure 2 or the M25 thread on the base Figure 3 D If using the three outer mounting holes recommended for installations exposed to shock and or high vibration Drill a central 40mm hole to pass the connector and base mounting thread through Position the SAT 201 and mark the location of the three mounting holes Drill three 4 5mm mounting holes Secure the SAT 201 in place using M4 No 8 screws and nuts D
17. he general purpose inputs INs Digital in Digital out High voltage Digital in Digital in falling edge interrupt High voltage Digital in falling edge interrupt Analogue in Figure 5 SAT 201 general purpose Input block diagram Figure 6 shows a conceptual drawing of one of the general purpose Outputs OUTs Figure 6 SAT 201 output block diagram IMPORTANT The factory default configuration disables the SAT 201 outputs OUT1 and OUT2 To use these outputs the user must ensure that they are Co configured as open drain outputs Failure to do so will cause unexpected results Page 18 of 22 Satamatics Ltd KCsatamatics MAN 0019 Issue 2 SAT 201 User Manual 12 INTERPRETING THE INDICATOR A single status indicator is provided on the SAT 201 The indicator goes through 4 states every 2 seconds generating the patterns in the table below State 1 State 2 State 3 State 4 Meaning RED RED RED RED Fault RED OFF OFF OFF D OFF RED OFF GREEN OFF Acquiring Bulletin Board GREEN GREEN RED RED Demodulating Bulletin Board GREEN ORANGE GREEN OFF Acquiring Traffic Channel GREEN GREEN GREEN OFF Demodulating Traffic Channel GREEN OFF OFF OFF Idle part of TC Frame ORANGE ORANGE ORANGE ORANGE Transmitting GREEN RED ORANGE OFF Software download in progress Normally from power on the indicator will go from flashing red D OFF through to flashing green as the SAT 201 first
18. nal has already synchronised to the traffic channel Figure 1 SAT 201 D Terminal Mounting is via 3x M4 No 8 bolts or central M25 thread on base Cable entry is from the centre base connector details are given in section 11 Satamatics Ltd Page 7 of 22 KOsatamatics SAT 201 User Manual MAN 0019 Issue 2 5 INSTALLATION A IMPORTANT Installation and service should only be carried out by suitably qualified Co service personnel Local working practices and regulations for wiring and installations must be adhered to at all times 5 1 Power Requirements The equipment is powered from an external DC supply of 9 6V to 32V The DC supply must be capable of providing a maximum VA of 9 6W for example 1A 9 6V or 0 3A 32V External power is connected via the 12 way connector see section 11 for connector details and pin connections When installing the SAT 201 adequate circuit protection must be provided as required by local regulations IMPORTANT If connecting to an external battery the SAT 201 requires an external fast acting fuse connected in series with the ve supply at the battery end of the cable Input voltage Fuse Rating Minimum wire gauge 9 6 to 32 VDC 1A 24 AWG 7 0 2 IMPORTANT If an external AC DC Adaptor is used to power the equipment it must meet the requirements of EN 60950 1 The output of the Adaptor must also meet the SELV limits of EN 60950 1 Uz tb 5 2 Cable I
19. o not over tighten Alternatively secure using screws appropriate to the mounting surface Do not over tighten Q If using the M25 base mounting thread Drill a 26mm hole to pass the connector and mounting thread through Secure using M25 nut Do not over tighten U 120 117 9 57 5 M4 CLEARANCE HOLE 3 POSITIONS Figure 2 SAT 201 M4 Drilling Diagram not to scale Page 10 of 22 Satamatics Ltd KCsatamatics MAN 0019 Issue 2 SAT 201 User Manual 108 2 45 10 8 M25 THREAD HEIGHT 3mm THICK FOAM WASHER Figure 3 SAT 201 M25 Drilling Template not to scale 60 FOAM WASHER O D 39 FOAM WASHER I D Figure 4 SAT 201 Foam Washer Dimensions not to scale Satamatics Ltd Page 11 of 22 KOsatamatics SAT 201 User Manual MAN 0019 Issue 2 5 5 Applying Power Before connecting the SAT 201 to an external voltage source ensure that the polarity is correct and the voltage source at the input to the SAT 201 is between 9 6V and 32V See Section 11 1 for connector pin out description See Section 5 1 for further details and requirements regarding the power source Check the circuit in particular fuses and or circuit protection devices Always ensure that the ground connection is connected before power is applied 5 6 Operational Check When the SAT 201 first powers up it includes instructions to start its GPS receiver After it has acquired its GPS
20. r Manual Ksatamatics MAN 0019 Issue 2 GPS test interface not available during normal operation Interface Baud rate Parity data bits stop bits Control amp Monitoring Interface Baud rate Parity data bits stop bits Data Interfaces 2 x Inputs 2 x Outputs Power Consumption Typical Sleep Receive incl GPS Transmit Power Supply Voltage Page 16 of 22 Asynchronous serial RS232 38400 bps N 8 1 Asynchronous serial RS232 9600 bps N 8 1 Individually configurable as o Digital input 32V maximum o Switch input internal pull up used with external switch to ground o SAT 101 compatible I O low voltage o Analog input 12 bit ADC 0 to 2 5V Open drain output 250mA max sink current 0 5mW 1 5W 6W 9 6V to 32V smoothed DC Satamatics Ltd KCsatamatics MAN 0019 Issue 2 SAT 201 User Manual 11 INTERFACES The interface connector is a 12 way plug that mates with a Bulgin Buccaneer 400 series socket Bulgin part numbers for the mating connector are PX0410 12S 6570 SA3179 1 pack of 10 SA3179 pack of 10 Contact Bulgin for crimp tool details 13027 Connector Solder contacts Crimp contacts Insertion extraction tool PON gt Items 1 2 amp 4 can be purchased as a kit from your equipment supplier or authorised dealer Satamatics part number 00925 11 1 Interface Connector Pinout The connector has the following pin connections
21. t is recommended that cable routing is planned and operation tested before committing to a permanent installation The maximum cable diameter must not exceed 7mm Q As standard the SAT 201 is supplied without cable or mating connector See section 11 for mating connector details Suitable cables and or connectors can be purchased separately from your equipment supplier or authorised dealer a When routing the cable avoid sharp edges and pinches D Be aware of the minimum static bend radius of the cable D Mechanical pressure on the cable may cause loss of functionality or even a short circuit and subsequent damage to the terminal Use only shielded cables for connecting to peripherals Using shielded cables ensures that the appropriate EMC classifications are maintained Page 8 of 22 Satamatics Ltd KCsatamatics MAN 0019 Issue 2 SAT 201 User Manual 5 3 Location The SAT 201 is only weatherproof if the interface connector is correctly mated with a Bulgin 400 series Buccaneer connector Please consult your dealer if you are in any doubt The SAT 201 should be located with an unobstructed clear view of the sky The SAT 201 should be mounted on a flat horizontal surface Consider the position of the satellites The Inmarsat satellites are in geostationary orbits above the equator i e in the Northern hemisphere the satellites are located to the South in the Southern hemisphere the satellites are located to the Nort
Download Pdf Manuals
Related Search