Model No. 2MCE-24P Two Machine, Cuts Only
Contents
1. the ST300 XXX XXX means hold the two keys down simultaneously The 5 SOFTKEYS are located just below the Display 4 2MCE 24P Two Machine Cuts Only Editor 3 5 INSTALLATION ST300 S SM VTR DDR CONTROLLER 1 Plug one end of a 9 conductor RS422 serial cable into the 9 pin connector VTRI VTR2 VTR3 on the rear of the ST300 Plug the other end of the cable into the 9 pin remote connector on the Video Server 2 Connect the 5 12 12 VDC POWER SUPPLY into the POWER connector on the rear of the ST300 Plug the Power Supply into a wall outlet 90 VAC to 240 VAC 3 Check SETUP MENU prior to using the ST300 to confirm proper Record mode and other User settable modes SELECT RECORDER Press SHIFT VTR1 SHIFT VTR2 SHIFT VTR3 or SHIFT VTR4 to select the RECORDER The VTR s LED will flash SELECT PLAYER Press VTR2 VTR3 to select the PLAYER The VTR s LED will turn on NOTE Selecting a PLAYER VTR will automatically put the RECORDER VTR into EE mode The selected PLAYER VTR indicator will turn on and remains on when the RECORDER is selected REFERENCE VIDEO INPUT Connect Black Video or the Tri level Sync for 24P editor to the Reference Video BNC on the rear of the 2MCE NOTE The ST300 will allow edits without sync SET THE VTR S COLOR FRAME MODE 1 Set the color frame on the RECORD DECK to ON 22. Press PREROLL to save the current value and exit OR Press ESC to exit without saving Installation is complete 6 2MCE 24P Two Machine Cuts Only Editor RECORDER VTR DDR 7 REFERENCE VIDEO BLACK BURST 2MCE t comas POWER GPI IN OUT Connection Diagram RESET PIN 1 5v PIN 3 GND POWER SUPPLY 2MCE 24P Two Machine Cuts Only Editor 4 8 OPERATION a TRIM AN IN OUT POINT 1 Press TRIM or TRIM The display will prompt Enter Time Select IN OUT 2 Enter the amount of trim using the numeric keypad The top row of the display will show the entered amount 3 Press IN to trim the IN Point Press OUT to trim the OUT Point The trimmed time will be displayed on the bottom row of the display CLEAR AN OUT POINT Press CLR OUT to clear the OUT point The OUT key indicator will turn off The OUT Point on Recorder and Player will be cleared to 00 00 00 00 GOTO IN OUT POINTS 1 Press GOTO The GOTO key Indicator will turn on 2 The display will prompt for IN or OUT 3 Press IN to goto the IN Point Press OUT to goto the OUT Point OR Press ESC to exit without searching CRASH RECORD NOTE Check the Record option in the Setup Menu It should be set to Crash Record 1 2 3 Select the Recorder Press SHIFT RECORD if the option in the Setup Menu is set to Rec only Press RECORD PLAY if the option in the Setup Menu
3. 5 VDC 2 5v DC 7 Ground 3 Ground 8 Ground 4 12 VDC 9 Ground 5 12 VDC GPI IN OUT CONNECTOR 15 Pin D Type Female DB15F Pin 1 GPI 1 Out Pin 9 GPI 1 In 2 GPI 2 Out 10 GPI 2 In 3 GPI 3 Out 11 GPI 3 In 4 GPI 4 Out 12 GPI 4 In 5 GPI 5 Out 13 GPI 5 In 6 GPI 6 Out 14 GPI 6 In 7 GPI 7 Out 15 GPI 7 In 8 Ground 17 2MCE 24P Two Machine Cuts Only Editor KEY LAYOUT 8 AEN HOLA jog LHS CAERA 953 14185 dud WAD asses 330 Gra p JH WAIA Jens LHI ino W19 KAD WIL WAIN TL 1 NOILLVONDIANOD 00515 2MCE 24P Two Machine Cuts Only Editor 18 9 DNF CONTROLS LIMITED WARRANTY DNF Controls warrants its product to be free from defects in material and workmanship for a period of one 1 year from the date of sale to the original purchaser from DNF Controls In order to enforce the rights under this warranty the customer must first contact DNF s Customer Support Department to afford the opportunity of identifying and fixing the problem without sending the unit in for repair If DNF s Customer Support Department cannot fix the problem the customer will be issued a Returned Merchandise Authorization number RMA The customer will then ship the defective product prepaid to DNF Controls with the RMA number clearly indicated on th
4. PREVIEW FUNCTION 1 2 3 4 5 Select Recorder VTR Record mode must be Assemble or Insert Set the IN point by manually entering a time using the numeric keyboard OR By pressing IN and marking the current tape time Set OPTIONAL OUT point using the same procedure as IN OR Set the OPTIONAL OUT point by pressing SHIFT OUT The display will show the current PLAYER duration Manually enter the desired duration using the numeric keypad Press OUT to save the entered duration OR Press ESC to exit without saving the entered duration Press SHIFT AUTOEDIT The machine will preroll to the IN Point The second line of the display will show Prerolling The machine will go into PLAY mode At the IN point the record ready channels will go into EE mode The second line of the display shows Autoedit At the OUT Point the record ready channels will go into playback mode Press STOP at anytime to abort the Preview 2MCE 24P Two Machine Cuts Only Editor Reference 5 SETUP MENU Press MENU The MENU indicator will turn on Turn the Wheel to select item to change Press ESC at anytime to exit SETUP MENU The MENU indicator will turn off MENU MODES Turning Wheel clockwise RECORD MODE Press MENU to select the desired record mode Lockout Crash Full Only in INSERT mode Press the associated Softkey locat
5. Set the color frame on the PLAYBACK to OFF 3 Set the VTRs Capstan Lock Set Capstan Lock on the Recorder to 2FD 2MCE 24P Two Machine Cuts Only Editor f SET THE RECORD DELAY 1 Press MENU The MENU key indicator will turn on 2 Turn the wheel until RECORD DELAY is displayed 3 Enter Record Command latency delay time in frames using the numeric keypad Typical value for SONY BVW75 is 3 frames 4 Press ESC to exit the SETUP MENU The MENU key indicator will turn off g SET THE RECORD MODE 1 Press MENU The MENU key indicator will turn on Turn the wheel until REC is displayed 2 Press MENU to toggle between LOCKOUT ASSEMBLE CRASH and INSERT record modes 3 In INSERT mode press the SOFTKEYS to select Video Audiol Audio2 Audio3 or Audio4 NOTE The 5 SOFTKEYS are located just below the Display 4 Press ESC to exit the setup menu Indicator will turn off h SET THE VIDEO STANDARD 1 Press MENU The menu indicator will turn ON 2 Turn the wheel until Video Standard is displayed 3 Press the softkey a key underneath the desired standard 24P NTSC or PAL to select a video standard to perform edits in 4 Press ESC to exit the setup menu i SET PREROLL VALUE 1 Press SHIFT PREROLL The display will show the current Preroll Value 2 Enter the desired Preroll Value using the numeric keypad The display will show the entered value 3
6. is set to Rec Play The record VTR will begin recording immediately There is no preroll in the Crash Record mode The RECORD key indicator will turn on Press STOP to end recording RECORD indicator turns off 2MCE 24P Two Machine Cuts Only Editor e PERFORM AN EDIT 1 2 3 4 5 6 7 8 9 10 NOTE Select the PLAYER VTR Set the IN point by manually entering a time using the numeric keyboard OR By pressing IN and marking the current tape time Set OPTIONAL OUT point using the same procedure as IN OR Set the OPTIONAL OUT point by pressing SHIFT OUT The display will show the current PLAYER duration Manually enter the desired duration using the numeric keypad Press OUT to save the entered duration OR Press ESC to exit without saving the entered duration Select the RECORDER Set the IN point by manually entering a time using the numeric keyboard OR By pressing IN and marking the current tape time Press PREVIEW to preview the edit Press REC to perform the edit The RECORDER and PLAYER will preroll then synchronize At the IN point the RECORDER will go into record At the OUT time the RECORDER will terminate record During the edit in INSERT mode press the Softkeys to punch desired channels into and out of record Press STOP at anytime to abort the edit OR For OPEN ENDED edits press OUT to terminate the edit Upon successfull
7. keypad Press OUT to save the entered duration OR Press ESC to exit without saving the entered duration Press REC to perform the edit The PLAYER will cue to the IN time The RECORDER will preroll The PLAYER will Slo Mo at the selected speed The RECORDER will go into play At the IN point the RECORDER will go into record At the OUT time the RECORDER will terminate record During the Edit turn the wheel to change the Slo Mo speed During the edit in INSERT mode Press the Softkeys to punch desired channels into and out of record 10 2MCE 24P Two Machine Cuts Only Editor 11 11 Press STOP at anytime to abort the edit 12 For OPEN ENDED edits press OUT to terminate the edit 13 Upon successfully completing the edit The RECORDER IN Point will be set to the record out time The RECORDER VTR will cue to its IN Time 14 Press OFF SPEED to disable off speed edit The SLOMO key indicator will turn off PREVIEW AN EDIT NOTE PREVIEW and REVIEW functions apply to INSERT and ASSEMBLE edit modes only 1 Press PREVIEW to preview the edit The PREVIEW key indicator will turn on 2 At the IN point the record ready channels will go into EE mode At the OUT point the record ready channels will go to playback mode 3 Press STOP at anytime to abort Preview 4 Upon completion the PREVIEW key indicator will turn off REVIEW AN EDIT Review mode is only available after a successful edit has been c
8. 12843 Foothill Blvd Suite D Sylmar CA 91342 818 898 3380 voice 818 898 3360 fax www dnfcontrols com Model No 2MCE 24P Two Machine Cuts Only Editor With 24P Editing Capability USER MANUAL 2MCE 24P Two Machine Cuts Only Editor 1 Table of Contents 1 REVISION HISTORY GETTING STARTED 2 DESCRIPTION STANDARD FEATURES DEFINITIONS 3 INSTALLATION ST300 S SM VTR DDR CONTROLLER B SELECT RECORDER C SELECT PLAYER D REFERENCE VIDEO INPUT E SET THE VTR S COLOR FRAME MODE F SET THE RECORD DELAY SET THE RECORD MODE H SET THE VIDEO STANDARD I SET PREROLL VALUE 4 OPERATION A TRIM AN IN OUT POINT B CLEAR AN OUT POINT C IN OUT POINTS D CRASH RECORD E PERFORM AN EDIT F PERFORM AN OFF SPEED EDIT PREVIEW AN EDIT H REVIEW AN EDIT I ONE MACHINE AUTOEDIT J ONE MACHINE AUDOEDIT PREVIEW FUNCTION REFERENCE 5 SETUP MENU 6 FUNCTION TABLE 7 SPECIFICATIONS RS422 SERIAL CONNECTOR POWER CONNECTOR GPI IN OUT CONNECTOR 8 KEY LAYOUT DNF CONTROLS LIMITED WARRANTY Manual Version Iud 112103 Document ID MCE 24P_User_Manual doc 2MCE 24P Two Machine Cuts Only Editor O 0 Eom Eom E wn 14 14 16 17 17 17 17 18 19 1 REVISION HISTORY 100903 1 0 Original document 112103 1 1 Added DNF Controls Limited Warranty 3 2MCE 24P Two Machine Cu
9. D SHIFT REC Places VTR in the Record mode selected by RECORD MODE in the SETUP MENU One button record RESET TAPE DEL TIME MODE Reset the Tape Time to 00 00 00 00 on the currently selected VTR TIME REWIND Press and HOLD to shuttle Release key to stop Set WIND Speed in MENU SHUTTLE SHUTTLE Select SHUTTLE mode and enable the Wheel STOP STOP Press once to STILL frame VTR Press again to put VTR into STOP mode TIME MODE TIME MODE Press to toggle between Timecode TC VITC VT or Tape Timer SELECT TM display modes TIME PRESET SHIFT Press to enter Time Preset Press ENTER to load Time Generator Generator Preset TIME MODE OR press ESC to exit without saving 16 2MCE 24P Two Machine Cuts Only Editor 7 SPECIFICATIONS Power Size Weight Real Panel Connectors Display Jog Shuttle Wheel 90 VAC to 265 VAC adapter supplied with IEC connector L x W x H 12 x 6 x 1 5 front 3 0 rear 4 165 VTR2 VTR3 VTRA All DB9F GPL diiit desit Se HARE DBFISF POWetz RUIT DB9M AUX ces eua dns DB9F Easy to read 4 line back lit LCD display User adjustable contrast With mechanical detents RS422 SERIAL CONNECTOR 9 Pin D Type Female DB9F Pin 1 Frame Ground 6 Receive Common 2 Receive A 7 Receive B 3 Transmit B gt 8 Transmit A gt 4 Transmit Common 9 Frame Ground 5 Spare POWER CONNECTOR 9 Pin D Type Male DB9M Pin 1 5v DC 6
10. al or other types of damage resulting from the use of the product HEE 19 2MCE 24P Two Machine Cuts Only Editor
11. e customer s shipping document The merchandise is to be shipped to DNF Controls 12843 Foothill Blvd Suite D Sylmar CA 91342 USA Failure to obtain a proper RMA number prior to returning the product may result in the return not being accepted or in a charge for the required repair DNF Controls at its option will repair or replace the defective unit DNF Controls will return the unit prepaid to the customer The method of shipment is at the discretion of DNF Controls principally UPS Ground for shipments within the United States of America Shipments to international customers will be sent via air Should a customer require the product to be returned in a more expeditious manner the return shipment will be billed to their freight account This warranty will be considered null and void if accident misuse abuse improper line voltage fire water lightning or other acts of God damaged the product All repair parts are to be supplied by DNF Controls either directly or through its authorized dealer network Similarly any repair work not performed by either DNF Controls or its authorized dealer may void the warranty After the warranty period has expired DNF Controls offers repair services at prices listed in the DNF Controls Price List DNF Controls reserves the right to refuse repair of any unit outside the warranty period that is deemed non repairable DNF Controls shall not be liable for direct indirect incidental consequenti
12. ed below the display to toggle Video V Audiol A1 Audio2 A2 Audio3 A3 Audio4 A4 on off SLOMO SPEED Press MENU to select the desired speed range RANGE 100 gt 200 or 0 3 200 SLOMO PRESET Press MENU to select the desired mode UPDATE or STATIC UPDATE When exiting OFFSPEED mode the last used speed is saved in the Preset Speed register STATIC The Preset Speed register is NOT updated when the wheel is turned Upon entering OFFSPEED mode the slomo speed 15 always restored to the preset value set by SHIFT SLOMO MAX WIND SPEED Press MENU to select the desired maximum wind speed WIND MODE Press MENU to select the desired wind mode LATCH or HOLD LATCH Fast wind is initiated and maintained with a momentary key press HOLD Fast wind is initiated and maintained only while key 1s pressed Upon releasing key wind mode terminates VIDEO STANDARD Press a Softkey to select the desired video standard PAL NTSC or 24P RECORD Press Softkey to select single button or 2 button record RECORD REC Only RECORD PLAY DISPLAY SOFTWARE The version number for the currently installed software 1s displayed VERSION CLEAR MEMORY Press DEL to clear the controller s internal memory Press ESC to exit without clearing memory SET FACTORY Press DEL to initialize the controller to factory defaults DEFAULTS Press ESC to exit without initializing controller to factory defaults 14 2MCE 24P Two Machine Cut
13. ompleted 1 Press REVIEW to review the previous edit The REVIEW key indicator will turn on 2 The RECORDER will preroll to the original IN point then play the edit At the OUT point the RECORDER will post roll 2 seconds then stop 3 Press STOP at any time to abort Review The REVIEW key indicator will turn off 2MCE 24P Two Machine Cuts Only Editor 12 ONE MACHINE AUTOEDIT 1 2 3 4 5 Select the RECORDER VTR Record mode must be Assemble or Insert Set the IN point by manually entering a time using the numeric keyboard OR By pressing IN and marking the current tape time Set OPTIONAL OUT point using the same procedure as IN OR Set the OPTIONAL OUT point by pressing SHIFT OUT The display will show the current PLAYER duration Manually enter the desired duration using the numeric keypad Press OUT to save the entered duration OR Press ESC to exit without saving the entered duration Press AUTOEDIT The recorder will preroll to the IN point The second line of the display will say Prerolling The recorder will be put into PLAY mode At the IN Point the recorder will go into Record The second line of the display shows AUTO EDIT At the OUT point the recorder goes out of Record and does a 2 second postroll then goes into STOP mode Press STOP at anytime to abort the autoedit 2MCE 24P Two Machine Cuts Only Editor 13 ONE MACHINE AUDOEDIT
14. s Only Editor TCSOURCE Press MENU to select RECORDER or PLAYER as time source during edit RECORDER is default and recommended setting EDIT MODE Press MENU to select the EDIT MODE or MODE2 MODEI All IN amp OUT marks will use Timecode as time type regardless of the TIME MODE selection MODE2 The currently selected TIME MODE will be used when marking IN amp OUT RECORD DELAY Manually enter the VTR Manufacturer s record latency in frames 0 99 15 2MCE 24P Two Machine Cuts Only Editor 6 FUNCTION TABLE AUTOEDIT AUTOEDIT Set IN time and Optional OUT Time Press AUTOEDIT and Recording VTR DDR performs an Autoedit using Assemble or Insert recording AUTOEDIT SHIFT AUTOEDIT Set IN time and Optional OUT Time PREVIEW Press AUTOEDIT SHIFT and Recording VTR DDR performs a preview of the Autoedit FFWD FFWD Press and HOLD to shuttle Release key to stop Set WIND Speed in MENU GOTO GOTO Search the VTR to the contents of the currently displayed IN or OUT In or OUT point or entered time JOG Select JOG mode and enable the Wheel OFFSPEED SHIFT OFFSPEED Play offspeed Turn wheel to change speeds PLAYBACK PREROLL PREROLL Preroll the VTR to the contents of the currently displayed Cue Point PREROLL SHIFT PREROLL Enter desired Preroll Value Press ENTER to save entry VALUE OR press ESC to exit without saving entry RECOR
15. ts Only Editor Getting Started 2 DESCRIPTION The 2MCE 24P is a two machine Cuts Only editor with the ability to perform 24P edits for HD media Fast easy to use news style editing Easy to read 4 line display quickly shows in out and duration Numeric keypad provides quick and easy entry of in out and duration Performs off speed Edits Change Source speed during edit Hot punch Video and Audio channels during edit STANDARD FEATURES Record Edit Play Stop Rewind Fast Forward Jog Shuttle Preroll GoTo Trim Trim Clear OUT Point Preview Review Off Speed Edit Video Reference input provides frame accurate edits Set IN amp OUT points by manually entering desired time OR By MARKing tape location Trim and TRIM keys and numeric keypad provide a fast and easy way to trim IN and OUT times Trim by frames second minutes or hours Easy to perform off speed edits Select source playback speed Set Source IN point Set Recorder IN and OUT point Perform the edit Change Source speed during edit During INSERT recording hot punch Video Audiol Audio2 Audio3 amp Audio 4 Punch In or Punch Out Optional 7 GPI Inputs and 7 GPI Outputs DEFINITIONS Q Throughout this document VTR DDR VDR amp Video Server will be referred to collectively as VTR Q The Two Machine Cuts only Editor will be referred to as the 2MCE Q Words surrounded by brackets for example ENTER are keys
16. y completing the edit The RECORDER IN Point will be set to the record out time The PLAYER IN Point will be set to the PLAYER out time The RECORDER and PLAYER will cue to their respective IN times and park Prior to performing an Edit the time type of the IN and OUT are checked If they are not both Tape Time or Time Code an Error message is displayed and the Edit is aborted 9 2MCE 24P Two Machine Cuts Only Editor f PERFORM AN OFF SPEED EDIT 1 2 3 4 5 6 7 8 9 10 Select the PLAYER VTR Press OFF SPEED The OFF SPEED indicator will turn on Press OFF SPEED again to disable off speed edit Turn the wheel to select the PLAYER s playback speed Select 0 00 for STILL frame To slo mo the VTR and select a slo mo speed press SHIFT OFF SPEED Turn the wheel Press STOP when done Set the IN point by manually entering a time using the numeric keyboard OR By pressing IN and marking the current tape time The PLAYER OUT Point is ignored Select the RECORDER Set the IN point by manually entering a time using the numeric keyboard OR By pressing IN and marking the current tape time Set the optional OUT Point by manually entering a time using the numeric keyboard OR By pressing OUT and marking the current tape time OR By pressing SHIFT OUT The display will show the current RECORDER duration Manually enter the desired duration using the numeric
Download Pdf Manuals
Related Search