MVA-24/24WD1/24WD2 User`s Manual
Contents
1. Beat Sonic NO 000001 MVA 24 24WD1 24WD2 User s Manual Thank you for your purchase of MVA 24 The following document is written to describe the installation process of this product Vehicle Application Model Year 2003 2006 Model Chassis Code UCF30 UCF31 Features 1 Can remove the factory unit and attaach 2 DIN size aftermarket head unit navigation with the amplifier 2 Can hear the sound from Woofer Tweeter Front and Rear door spealers 3 Can use the OEM NAV TV as it is However cannot display anything while driving 4 Can adjust the TV channel and the volume using the OEM steering switch 5 Can display the image on the OEM screen items needed are not included 6 The color of the supplied panel is similar to the OEM head unit Cautions 1 Not compatible with cars without the factory steering switch 2 May cause a noise when using key on key off with a certain unit 3 Channel up down on the steering wheel corresponds to TV channels only when the OEM head unit displays TV Otherwise the channel button do not function 4 Not compatible with Lexus LS430 5 Cannot exchange the OEM navigation and display with this adaptor About the aftermarket head unit 1 The aftermarket head unit has to have the speaker outputs 2 Because of the 2ch OEM amplifier the effect from the additional unit such as fader DSP cannot work properly Only when used by Multi Vision fader DSP w2. SE L QE e F Rear R oe CO pa Black Ground Blue White Amp Remote O f 4 a Red Ignition Power ACC Yellow Battery Constant Orange IIlumination Dimme 20PIN S77 Coupler EA 12PIN x Coupler 4 A Junction SPIN ke VL E Coupler Coupler z Please connect it with that when TYR there is AUX input a new head unit Precautions BEFORE Installation Process Always disconnect the negative terminal of the vehicle battery and drain all capacitors before installation Use the masking tape to label the wires passing near the metal part of the car After the installation make sure the brake lamps headlights turn signals and wipers work properly Before starting installation verify that the original audio system in the vehicle is fully functional This kit will not remedy any issues that existed before the installation or faults in the original systems in the vehicle Caution LD Removal of the Factory OEM Audio Head Unit 1 Remove the switch panel below the OEM unit 2 hooks 2 LOEM unit EAO o 2 Remove the center compartment 3 screws 6 hooks Remove the switches from the center compartment 3 Remove the OEM unit 2 bolts 2 hooks c Remove the hazard switch from the OEM unit 2 screws L3 Antenna
3. cable connections Connent an antenna cable to A the right bottom of the trunk Remove the wiring harness attached to A radio tuner then attach to the extension cable Extend the antenna plug to C the back of the unit through the wiring hole located in B the back of the backseat How to display the image from the new heat unit on the OEM To display the image from the new head unit on the OEM AVC1 or VTR adaptor not included is neede Connect AVC1 to the OEM TV tuner located in A the right bottom of the trunk Attach AVC1 to the video cable then connect with C the back of the unit through the wiring hole located in B the back of the backseat Attach the video cable to the new head unit video output or the rear monitor output Do not connect anything to AVC1 sound input Please see Basic operation for information on how to display the image from the new head unit on the factory screen
4. f extreme temperatures for installation Any damages resulting to the automobile of aftermarket audio systems as result of inproper installations or careless installation prodecures are not covered by any warranty nor are we responsible for any injuries or damages resulting Caution rom the installation process Please observe caution when performing installation Beat Sonic USA 14778 Beach Blvd La Mirada CA 90638 Tel 714 944 1085 Fax 714 944 1085 amp 2 Installation of adaptor CX 1 Amplifier Remote wire 1 When listening to audio from the TV Depending on the manufacture of using AUX input and when turning off model of the aftermarket radio the audio from the TV while the new head referece and names of the amplifier unit is off connect to ACC remote trigger wire may differ 2 When no remote terminal for the new Prease refer to the instructions as head unit is available and when New Head Unit a provided by the respective audio controlling audio from the TV regardless unit to be installed of turning on off the new head unit i connect to ACC through the switch Please make ALL of the following connections for proper operation O ET Front 5 R
5. ork with the additional unit About the factory system 1 Cannot use the factory unit s features such as VICS and FM multiplex telecasting etc 2 Cannot use rear controller 3 Cannot use CD changer and optional DVD changer 4 Can use the audio functions such as DSP Equalizer and POS on the factory Multi Vision screen 5 Channel up down on the steering wheel corresponds to TV channels only when the OEM TV Otherwise the channel buttons do not function 6 Cannot use the factory FM AM radio Need to attach the supplied antenna cable from the trunk to the back of the unit when listening to FM AM radio using the new head unit 7 About the navigation sound Can hear the navigation sound when the front speaker on the right on the passenger s side is muted Control the navigation sound and the volume by the MENU on the navigation screen Attached panel color MVA 23 OEM Color MVA 23WD1 Light Brown Color MVA 23WD2 Medium Brown Color Specification Installation 2 DIN 40mm Width x 26 5mm Height x 82mm Depth Weight 150g only adaptor Included in this kit Audio Electronic Adaptor Face Plate Brackets L R Antenna Cable Mount all components in locations that will not inhibit safe driving or obstruct the motions of the various components of the vehilce function Be cautious so as not to damage wires piping tanks and other areas as Donot installed in the vehicle Avoid wet dusty or areas o
Download Pdf Manuals
Related Search