RL 7 2+1 - RL 7 Monospeed
Contents
1. ATTENTION Before maintenance or repairing works switch always the engine off and take the candle connection away 8 CONTROL SIGNS MB TRANSMISSION FITTING THROTTLE LEVER ey SPEEDS SELECTOR ONLY RL7 2 1 9 SAFETY WARNINGS 1 This machine has been designed and manufactured for being used by one operator only and is driven by means of the appropriate handlebars Any other use is not permitted 2 Before the machine is operating read the Use and Maintenance manual thoroughly so that you are fully aware of all the operating controls and safety aspects of the machine Before starting the engine be sure that speeds selector is in position F and the SAFETY DEVICES are well working and fitting Without these cares the operator might work in a danger situation DON T SABOTAGE THE ENGINE STOP SAFETY DEVICE AND THE DISENGAGEMENT DEVICE THE MACHINE MIGHT BECOME EXTREMELY DANGEROUS 3 Do not under any circumstances transport people or objects on the machine 4 Always ensure that the machine s safety devices are correctly mounted and in perfect working condition 5 Before use check that all the controls in particular the clutch the Motor stop and the brakes if fitted are in good working order 6 Any modification or spurious parts being fitted without the Manufacturer consent will nullify the guarantee and any possible resulting damage will not answered for 7 This machine must not be used2. Oil is at the right level in the gear box pic part A Hold the clutch control lever lifted pic 2 Make sure that the gear shift lever is in the F NEUTRAL position pic 4 part A only RL 7 2 1 Turn the accelerator lever of 1 4 to the idling speed position pic 3 part B with cold engine engage the starter device Hold the start handle pic part C of the recoil starter with one hand only and pull smoothly until the ratchet gear engages and then pull sharply Once the engine starts the rope has to be left gently as far as completely wound Once the engine starts put the accelerator lever pic 3 part B to the idling position and let the engine warm up Release the clutch control lever pic 2 part 1 Make sure that the gear shift lever part 2 is in the neutral F position pic 4 part A only RL 7 2 1 3 Turn the accelerator lever pic 3 part B until the engine runs idle or is in the STOP position 4 Turn the engine stop switch 5 Close the fuel cock if it is present NO ma Part A ONLY ON RL7 2 1 Pic 4 11 CONTROLS UTILIZATION ACCELERATOR CONTROL LEVER For Sinopower 168F engine For Honda GC160 engine Leverup IDLING Lever back IDLING and ENGINE STOP Lever down MAXIMUM SPEED Lever forward MAXIMUM SPEED ENGINE STOP SWITCH CLUTCH CONTROL LEVER Lever DOWN the clutch is engaged motorhoe moves forw
3. MAIN PARTS 1 Accelerator 2 Clutch and disengagement lever 3 Handlebar adjustment 4 Gear shift lever RL 7 2 1 5 Adjusting screw for spur height 6 Blades 7 Tiller guard 8 Handlebar 9 Spur 10 Transport wheel RL 7 TECHNICAL DATA Recoilstarter Transmission by chain with an opening guard hood RL 7 241 Gear box in oil bath with 2 forward speeds and reverse Belt clutch with stretcher Dry air filter or in oil bath Fully adjustable handlebar 60 80 cms tiller with side discs Transport wheel 17 EQUIPMENT AND ACCESSORIES Boran TILLER SIZES i 80 cms tiller with guard side discs RL 7 MONOSPEED ACCESSORIES Adjustable ridger with coupling Descriptions figures and technical features mentioned herein are non binding for the Manufacturer These are mentioned as mere information The Manufacturer reserves the right to make any change at any time without being bound to update this publication Copyright of MECCANICA BENASSI S p A 11 ATTENTION For your safety please follow these instructions Wear guard ears Strong noise may damage the hearing During working vibrations may give you aching to hands and arms It is always better stopping working every 10 minutes as lack of sensibility may be dangerous GB CE DECLARATION OF CONFORMITY In compliance with CEE 89 392 regulations and subsequent changes CERTIFICATE OF ORIGIN MECCANICA BENASSI S p A 1 44040 DOSSO FE via
4. by children or inexperienced persons 8 Before operating the machine check that the area is clear and free of debris and that there are no people within the working area danger zone The operator will be held responsible for the safety of third parties if these are found within the working area of the machine Do not use the machine under these conditions 9 Keep clear of cutting blades at all times while the machine is in operation Pay particular attention when reversing keep hands and feet clear 10 Use the machine only with the handles in the correct working position This allows a safe working distance between the operator and operating area 11 Use only original accessories and spare parts to guarantee safety and correct operation of the machine 12 Stop engine before refuelling and remove ignition key if fitted 13 Handle the fuel with care to avoid spilling on the machine clean any spillage immediately 14 Never refuel in confined places in vicinity of open flames or near the source of sparks No smoking 15 Before starting the engine check that all the controls are in the idle position 16 Do not smoke when starting the engine 17 Do not run the machine in a confined area as toxic exhaust gas can kill 18 Plan your work before commencing 19 Do not use the machine when you are tired 9 SAFETY WARNINGS 20 Engage the clutch gradually sudden engagement could cause the machine to rear up 21 The area next to
5. the engine exhaust will most likely reach temperatures above 80 Attention Danger of scalding 22 Always wear close fitting clothes and anti slip shoes or boots For safety reasons avoid using loose clothing 23 Make regular checks that all bolts and nuts are well tightened 24 Keep the area of work clear and clean 25 Only use the machine in clear visibility 26 Avoid working with blunt cutting blades 27 Pay maximum attention and use good sense when operating the machine 28 If you hit any objects during work stop the machine and check for any damage immediately 29 During movement to and from the area of work disengage the Power Take Off P T O 30 Pay attention when reversing the machine not to trip over anything If you loose your balancer release the handlebars immediately the Motor stop or the disengagement will immediately stop the machine 31 Do not under any circumstance attempt to by pass the motor stop device or remove the disengagement device The machine would result having no safety precautions and would be extremely dangerous 32 Do not travel down hill with the clutch disengaged or the gears in idle 33 The machine s speed must always suit the conditions and the environment 34 Do not perform cleaning or maintenance operations of the machine when the engine is running 35 Avoid sharps turns when travelling up hill down hill or across steep slopes 36 In steep descents do not disengage the drive and d
6. the spur depth 2 by screw 3 BELT ADJUSTMENT Remove the guard casing Pic 1 Part A unscrewing part B pic 1 Verify that belt is well pulled with clutch lever down Pic 2 Part C while with the same lever Lin ap up belt is free to move inside pulleys Pic 3 Part E e On the contrary it is necessary put the engine in its right position a little bit unscrewing 1ts screws Pic 3 Part D by sliding it along slots of its support Done this adjustment fix the engine and fit the guard casing again Pic 1 Part A IMPORTANT JA SA o lt Jar i a o NE NL It is better that this adjustment is done by a specialized persons Pic 2 Pic 3 TILLER GUARD CASING The tiller is protected by a guard Part 1 and its widenings Part 2 that must be always fitted when working In compliance with safety and accident prevention regulations guards must be always fitted before starting the use of the motorhoe verifying that screws are very well tightened A 13 MAINTENANCE GEAR BOX only RL 7 2 1 IMPORTANT Change oil after the first working hours running in Oil has to be change when the engine is hot to facilitate its draining Remove the breather cap pic 1 part 1 Remove the drain plug pic 1 part 2 placed at the bottom part of the gear box and let the oil drain off Then refit the drain plug again Fill fresh oil with the following features AGIP DI
7. ESEL SIGMA SAE 30 Check the oil level when the machine is going to be used and change it every 300 working hours For what the engine concerns read carefully the manufacturer s booklet GEAR BOX Whenever the machine needs maintenance or overhauling use only original spares of the manufacturer to ensure always the best reliability to the machine ENGINE Follow carefully the instructions contained in the relevant use and maintenance booklet During the running in and in the first working hours of the machine avoid heavy jobs and follow the instructions 14 ASSEMBLY AND DISASSEMBLY TILLER f The tiller is fixed to the transmission shaft by screws A The tool holder shaft has got a cylinder profile so that the tiller may be quickly fitted Clean tiller hubs and the tool holder shaft Lubricate this in order to make easy its assembly and disassembly Fit tiller hubs 1 and disc 2 on the tool holder shaft fixing them by screws 3 and nut 4 NOTE The cutting part of blades must be always put fi towards the running direction RUNNING Each time you start working verify that screws DIRECTION and nuts are well tightened 10 15 TRANSPORT Moving the machine for a short way use the small transport wheel or fit a pair of side travel wheels In other situations put the machine on a pallet after a good fastening and load it on a truck by a forklift 16 TECHNICAL FEATURES
8. Statale 325 DECLARES under is own responsability that the item called MOTORHOE Model RL 7 From series no 700000001 The number is printed on the machine s gearbox is manufactured by the above company in compliance with basic safety and health safeguard requirements specified in the regulation CEE 89 392 and subsequent changes For checking the conformity with the above regulations have been examined the following CEN rules UNI EN 709 98 A1 2000 Dosso Italy the Ist June 2004 MECCANICA BENASSI SPA L Amministratore Unico oe IF YOU NEED SPARE PARTS PLEASE PUT YOU IN TOUCH WITH MECCANICA ms INI YA 9 WY R GE Sorat ENASSE srs DOSSO FERRARA ITALY Via Statale 325 Tel 0532 848091 Telefax 0532 848272 www benassi meccanica com e mail info benassi it HOW TO DO TT CLEARLY SPECIFYING IN WRITING a NAME OF THE MACHINE b FRAME NUMBER c POSITION CODE NUMBER AND DESCRIPTION d QUANTITY FOR ANY SPAREPART YOU NEED CONSULTING THE RELEVANT SPAREPARTS BOOK
9. ard or in reverse if selected Lever UP the clutch is disengaged motorhoe stops Setscrew for belt tension regulation part 1 N B BEFORE USING THE MACHINE IT IS IMPORTANT TO VERIFY CAREFULLY THE GOOD WORK OF THE SAFETY DEVICE GEAR SHIFT LEVER only RL 7 2 1 Hold the clutch lever UP part 1 Move the gear shift lever in the required position part 2 See plate pic 4 part A page 5 RL 7 2 1 3 Accelerate by the lever part 3 pull down the clutch lever slowly part 1 and the motorhoe starts running 4 To disengage the speeds keep the clutch lever up and move the lever part 2 to neutral position WARNING Always keep the clutch control lever UP when gears are shifted 6 12 ADJUSTMENTS HANDLEBAR ADJUSTMENT IMPORTANT Handlebar is adjustable in height and on the side ways with the possibility to block it in the wished position do this by the nut 1 After blocking the handlebar check that teeth of the blocking device are well connected Vibrations during the work may give aching to hands and arms It is always better stopping working every 10 minutes as the lack of sensibility may be dangerous WHEEL ADJUSTMENT In working transport wheel must be raised For the transport of motorhoe remove the lock pin 1 lower the wheel 2 and fit again the lock pin 1 using the upper hole IMPORTANT Spur support can move slowly in a side way 1 It is possible to change
10. ccanica BENASSI v oie 44040 DOSSO VIA STATALE 325 FERRARA ITALY TIPO The CE mark ison the engine support right side POTENZA KW ANNO 200 gt 3 CONDITIONS AND USE 4 WARRANTY This manual gives you general information on how this machine should be used and maintained For any technical problem please call Your confidential dealer This machine has been designed to be used in compliance with what specified in the machine descriptions and safety warnings of this instructions manual gt Any other use is not allowed The manufacturer is not responsible for damages caused by any use then the intended use The user is fully responsible for any possible risk gt Use maintenance and repair clauses prescribed by the manufacturer are also integral part of the machine intended use Only people familiar with this machine and well aware of its hidden risks can use repair and maintain it The manufacturer is not responsible for damages caused by non authorized changes made on this machine Besides warnings mentioned in this manual please also comply with general regulations on safety and accident prevention of EEC and the country in which this machine will be operating gt gt gt B Descriptions figures and technical features mentioned herein are non binding for the Manufacturer These are mentioned as mere information The Manufacturer reserves the right to make any change at any time without bein
11. ePATR AP e GB ME 05 05 a i F CCIAT MECCANICA BENASSI sn MOTORHOE RL 7 241 RL 7 Monospeed 1 FOREWORD Pag 0 2 IDENTIFICATION AND MARKING Pag O 3 CONDITIONS AND USE Pag 1 4 WARRANTY Pag 1 READ THIS MANUAL CAREFULLY 5 MACHINE STARTING Pag 2 6 PACKAGE OPENING Pag 2 dd a 7 WARNING SIGNS Pag 2 This manual cannot be either reproduced or released without the 8 CONTROL SIGNS Pag 3 manufacturer s prior written consent 9 SAFETY WARNINGS Pag 3 4 PRINTED IN ITALY 10 ENGINE START UP ENGINE STOP Pag 5 1 a FOREWORD 11 CONTROLS UTILIZATION Pag 6 12 ADJUSTMENTS Pag 7 8 13 MAINTENANCE Pag 9 14 ASSEMBLY AND DISASSEMBLY Pag 10 15 TRANSPORT Pag 11 This symbol is used to highlight an important safety information If 16 TECHNICAL FEATURES Pag 11 this information is ignored people are in danger either of possible injures even serious ones or death 17 EQUIPMENT AND ACCESSORIES Pag 11 IMPORTANT 18 WARNINGS CONFORMITY DECLARATION Pag 12 This term highlights special precautions to be taken in order not to ENGINE damage the machine Use and maintenance instructions of the engine are mentioned in the relevant manual copy of which is always supplied with every machine 2 IDENTIFICATION AND MARKING IMPORTANT NOTE Always mention the machine serial number when calling our technical service or when ordering spare parts MARKING Marking example quer Me
12. es are concerned regulations of our supplier will apply and applications for possible technical service should be addressed to the local specialized technical service centres A ECCANICA T q Q lt cyat BENASSI spa DOSSO FERRARA ITALY Via Statale 325 Tel 0532 848091 Telefax 0532 848272 www benassi meccanica com e mail info benassi it 5 MACHINE STARTING READ CAREFULLY THE WHOLE MANUAL BEFORE MOTORHOE STARTING NOTES The manufacturer aims improving both design and quality of his products As a consequence even though this manual includes latest and most up dated information available when printed there might be small differences between your machine and the information of this manual For any doubt or uncertainties on this manual please call our authorized dealer This manual is an integral part of this machine and should always accompany this machine when sold 6 PACKAGE OPENING IMPORTANT Keep the motorhoe away from the carton Opening it in the upper side loosing the part 1 and getting the handlebar ready 2 as you may See in the picture WARNING read carefully instructions on page 7 8 WARNING Comply with what specified in control warnings and warning DANGER Blades and rotating parts in operation Keep hands and feet away signs ATTENTION LLI Read use instructions DANGER Keep children away x from the machine
13. g bound to update this publication Copyright of MECCANICA BENASSI S P A If in doubt on causes and possible solutions for a certain trouble please call our authorized dealer This should be absolutely done during the warranty period since any repair made by non authorized workshops makes this warranty null and void Bear always in mind that the authorized dealer has all special tools technical specifications and spare parts necessary for properly fixing the machine Therefore he should be called in case of any doubt on maintenance specifications and or procedures Some pages of this manual might not be perfectly right due to misprints or production changes For this reason call Your dealer before being perfectly familiar with this machine and personally maintaining this machine For further information on use and maintenance of this machine ask your authorized dealer for the proper technical manuals Our materials have a 12 months warranty coverings and electrical parts are not included The manufacturer agrees on replacing those parts considered as faulty free of charge Purchaser will be charged with labour costs necessary for repairing the machine and possible transport costs Both the warranty claim and the returned piece should always be addressed to our Spare Parts Department and accompanied by regular freight bill mentioning all the machine details As far as materials available on the market especially engin
14. o not change gear 37 When possible avoid working up or down hill Always travel across the slope 38 Do not work on very steep slopes max 30 39 Avoid overfilling the fuel tank It is important that the working position of the operator is always behind the handlebar 40 If there is fuel in the tank avoid tilting the machine during maintenance or adjustment 41 During use keep the hot sections of the engine 1 e cylinder head exhaust etc clean to avoid a build up of debris that will overheat the engine 42 Whenever possible stop the machine on level ground 43 When stopping on unlevelled ground engage Istgear up hill or reverse gear down hill 44 If leaving the machine for a long time ensure it 1s inaccessible to children and inexperienced people Close the fuel tap af fitted 45 Do not leave the machine with the engine running 46 The maintenance instructions of the machine must always be carefully followed and worn parts replaced when necessary 47 If the machine is to remain unused for some time clean it accurately and insert the appropriate protections 48 Apart from the previous items it is necessary to take heed of the specific safety norms in force in the Country where the machine is operating 10 ENGINE START UP Follow the instructions contained in the engine s USE AND ppo MAINTENANCE booklet ng Before starting the engine up always check the following There is fuel in the tank
Download Pdf Manuals
Related Search