DS-SERIES
Contents
1. www avsi fluxia com NY fluxia DS SERIES Dimmable LED Ceiling Panels Item ref 154 926UK 154 927UK 154 928UK User Manual an NS group brand NY fluxia A Caution Please read this manual carefully before operating Damage caused by misuse is not covered by the warranty Introduction Thank you for choosing Fluxia dimmable LED ceiling panels for your lighting installation The panels and accessories supplied are intended for professional use only and should be fitted by a qualified electrical installer Please use the following instructions as a guide when installing these products Package contents LED ceiling panel Dimmable LED driver Ceiling suspension kit User manual If any parts or accessories are missing contact your dealer immediately Safety Fluxia LED panels are professional mains powered items and should only be installed by a qualified electrical installer All mains connections must be made in accordance with the appropriate safety regulations Do not attempt to use alternative power supplies or power more than one panel from a single driver To prevent the risk of fire or electric shock do not expose any components to liquids or moisture Avoid impact extreme pressure or heavy vibration to the housing No user serviceable parts inside Do not open the panel A Warning The LED driver supplied with this panel must be earthed Placement Ensure adequate support from ceiling or grid structure for2. the weight of all panels to be suspended Do not place heavy weights on top of the panel Allow enough slack in cables and connections for servicing and access Cleaning Clean the LED panels periodically for efficient performance using a clean dry anti static cloth A lightly damp cloth may be used to remove stains allow the panel to dry completely before use Do not use solvents on any part of the housing DS series LED Ceiling Panels User Manual NY fluxia Installation Fluxia LED panels will sit directly into the T bars of a standard modular ceiling grid Ensure the correct size format for the ceiling scheme If there is no ceiling grid a panel may be hung from the ceiling using the suspension kit supplied The kit comprises 4 steel cables 4 flanged ceiling anchors with screws and 4 M10 fasteners This kit enables suspension of the LED panel for up to 1m from the ceiling To suspend the panel from the ceiling note the 4 threaded studs which are fitted near to each corner of the LED panel Mark out fixing points on the ceiling corresponding to these studs Depending upon the ceiling material it may be possible to drill through the ceiling to allow excess steel cable to be fed into the ceiling void Otherwise each steel cable will need to be cut to length Each ceiling anchor requires 3 fixings which will depend upon the ceiling type and material wood screws are supplied for timber ceilings Position the flanged ceiling
3. anchors against the markings on the ceiling mark out the 3 holes and fix each anchor securely to the ceiling Fix each of the M10 fasteners to the 4 threaded studs on the upper edge of the LED panel and push one end of a steel cable into the narrow end until it stops The cable will lock so that it cannot be pulled out but this can be released if necessary by pushing the narrow end of the fastener inward Whilst supporting the panel thread the opposite end of each steel cable into its corresponding ceiling anchor and through until the correct height adjustment is achieved Again the locking anchors can be adjusted in turn by pushing the narrow end inward to release the cable DS series LED Ceiling Panels User Manual NV fluxia Connection Each LED panel is supplied with a dimmable LED driver The input side of this driver must be connected to the mains supply by a qualified electrical installer All relevant wiring regulations must be observed when connecting to the mains power supply and this driver must have a proper Earth connection for safety Insulate any exposed wiring connections CONNECT TO LED PANEL BLUE NEUTRAL LED DIMMER DRIVER BROWN LIVE Input 100 2402 50 60Hz AA y fluxia YELLOW GREEN EARTH CONNECT TO 0 10V DIMMER IF REQUIRED The output side of the LED driver has 2 wires One is an EL power lead which connects with its counterpart on the LED panel and the other is a male DC5521 jack socket which
4. can receive 0 10Vdc control voltage for PWM dimming When the DC5521 jack is not connected the LED driver operates as normal at full output to the LED panel If a standard 0 10Vdc dimmer is connected to the DC5521 jack the LED panel will operate as a dimmable luminaire Specifications 154 926UK 154 927UK 154 928UK 600 x 600mm modular ceiling tile Power supply 100 240Vac 50 60Hz Voltage 30 42Vdc Dimming control 0 10V Housing material PMMA plastic amp aluminium LED lifespan gt 50 000 hours LED colour Cool white Colour temperature 2800K 4200K 6200K Total luminous flux 2950 m 3100Im 3250Im Luminous efficacy 611m W 641m W 67Im W Colour rendering index CRI Ra 81 Beam angle gt 120 IP rating IP20 Dimensions 595 x 595 x 15mm Weight 3 56kg Electronic equipment and should not be disposed with other household or commercial waste at the end of its useful life X Disposal The Crossed Wheelie Bin symbol on the product means that the product is classed as Electrical or tu The goods must be disposed of according to your local council guidelines Errors and omissions excepted Copyright 2014 AVSL Group Ltd DS series LED Ceiling Panels User Manual
Download Pdf Manuals
Related Search