User`s manual User`s manual - Pdfstream.manualsonline.com
Contents
1. between the jointer of the water inlet hose and the water faucet and the installation of the water inlet hose are firm so as to prevent dropping from improper installation position Dismantle the water inlet hose 1 Close the water faucet 2 Press the locking lever Push down the slider Then pull of the water inlet hose Locking level Slider If the machine is used frequently the jointer of the water inlet hose can be kept on the faucet to prevent damaging the fixing screw 1 Preparation before washing Preparation before washing 1 Connect the water inlet hose 2 Confirm that the washing machine is earthed reliably Then insert the power plug into the receptacle Do not connect the earth terminal to the gas pipe and tap water pipe 3 Put down the drain hose Pay attention to followings before washing the laundries Confirm if there s special requirement for the laundries Clear the pocket Take out the coins sand hairpins etc oT Q AO Fasten the buttons and zippers The quantity of the laundries shall not exceed the rated value The big laundries like the jeans shall be put in loosely Y When the pulsator is running the buttons of the laundries may cause noise For the sake of discretion please put the laundries with buttons into other laundries RR N a Check if the laundries are applicable for washing with machine b Divide the laundries with2. after it has supplied water for 2 times during the whole process Open and close the top lid once The machine does Not wash not act Is there power failure Is the power plug inserted tightly Please use it when there s power supply Insert the power plug tightly Fill water to the preset position Not spin Is the water level reached preset position Is the power plug inserted tightly Is the top lid closed reliably Are the laundries set flat Insert the power plug tightly Close the top lid There s abnormal sound inside the machine Is the machine slanting Are the laundries put slantingly in spinning Are there any foreign materials Adjust the machine to be even Reorder the laundries and close the top lid Remove the foreign materials The water tap leaks Is the screw of the jointer of water inlet hose loose or awry Fasten the screw of the jointer properly Common phenomena Phenomena Explanation The spinning is intermittent when it starts Balance the laundries to avoid slanting The wash procedure pauses The cloth sensor is detecting the cloth It will start adding water after about 48 seconds Select SPIN program but it does not work The program is setting the drain time A certain period is needed before it starts spinning The pusaltor pauses during washing rinsing or adding w
3. etc e The handicapped or children without care shall not use the machine e Keep the machine away from direct sunlight and heat source like the heater Please keep the lint filter in good condition and install it to proper position during washing If the lint filter is lost or damaged please contact the local after sales service department of our company 2N The front cover of lint filter dismantle gt The back cover of lint filter e To protect your laundries and washing machine please take out all of the coins buttons sand hairpin and other foreign materials before washing lt P ob e Please check if the water faucet is open and if the connection of the water inlet pipe is proper Itis suggested to use foamless washing powder Installation and adjustment Please install and adjust the machine according to the requirement of the manual It is very important to your security and correct operating the machine Install the inner cover component 1 Open the top lid of the washing machine 2 Put the inner cover component on the outer tub cover aiming the inner cover shaft to the installation hole of the corresponding outer tub cover shaft groove 3 Firstly insert the inner cover shaft of one side into the corresponding outer tub cover shaft groove then push the another inner cover shaft into the corresponding outer tub cover shaft groove Please install to designated position to guarant
4. keep pressing RESERVATION CALEFACTION Button for morethan 2 s If the decimal pointof digitron is lighted it means heating function is selected The initial temperature isabout 30 C and you can selectyour desired value ina switching sequence 30 C 40 off 20 If keep pressingthe RESERVATION CALEFACTION button formore than 2 s again the temperature indicatorturns off andthe Reservation can be selected you can selectreserved time After the machine startsrunning if selection orcancellation of heating function isdesired you should switchoff the power and reselect 11 PROGRAM m E E EENE NENEN E WATER LEVEL on the power Ifthe START PAUSE button is not pushed the washing machine will automatically switch off the power after 5 minutes a a a POWER ON OFF START u m a PAUSE After the power is switched on push it to Start the machine During working push it to pause working During pause push it to resume working PROGRAM selection button Following automatic programs are available for selection PROGRAM STANDARD QUICK POSTHASTE Super Super quick wash of the laundry under 1 kg Applicable situation Common washing ouka an high efficiency wash for light soil JEAN Washing the relatively big and thick laundries FIBER COTTON WOOLLEN SILK Washing the textile Washing the chemical fiber laundries Washing the cotton textiles W
5. reservedwash cycle andthe indicator turnson e Tochange the running program or cancelthe reservation you should cutoff the supply and reselect e Confirm the heating function Keep pressing the RESERVATION CALEFACTION button for morethan 2 s the heating indicatorturns on red e Keep pressing the RESERVATION CALEFACTION button for morethan 2 sagain the heating indicator turns off and heatingfunction is cancelled After the machinestarts running ifselection or cancellation of heating function is desired you should switch offthe power andreselect 6 Push the START PAUSE button ae START PAUSE 5 Close the lop lid 6 Finish washing we As the top lid opened the Washer will automatically give an alarm After finishing wash it will alarm and stop running exclusively during supplying water and rinsing automatically 14 7 Disposal after washing After using please clean the lint and foreign materials of the lint filter etc in time Otherwise it may influence your using the machine Please first pull off the power plug from the receptacle before cleaning Clean the detergent box and set it on The lint filter must be used during washing the control panel seat e It must be cleaned in time after each using 1 The method of dismantle Push it up aslant and gently 2 The method of install install it upwards and aslant Lint filter and push it in 1 Rotate the inner tub with hand till the lint filter r
6. Fuzzy Computerized Automatic 1 Washing Machine User s manual This manual is for XQS60 78H Please read this manual carefully before using Retain it for future reference W 0030804888A CONTENTS Names OF the PANTS seciccascwesses ose secscasceweecdestdavekreicoeteanegetentes 1 Safety precautions ccccecccecccececeeeeseceeeceeeceeeseeeseeeseeeeenees 2 Installation and adjustment cecceeceeeeeeeeeeeeeeeeeeeeeeeeees 4 Install the water inlet NOSC ee eeeeeeeeeeeeeeteeteeteeeeeteeaeenees 6 Preparation before washing cceccesceeeeeeeseeeeeeeeeeteees 8 Put inthe laundries osceno arininn ona ennvererrncnbaas 9 Put in the detergent c ccceccesceeeeceeeeeeeeeeneeeeeteeeteeeeenees 9 Use the operation buttons cceccccccscecssescsseecseeeesseeesaees 10 Close the top lid niiina 14 Finish washing 2 ccecccecceeceeeeeeeceeeeeeeeeeeeseeeaeeceeeaeeeeseaeenaees 14 Disposal after WaShiNg 2 cesccecececeeeceeeceeeeeeeeeereeereeaeeneees 15 Trouble shooting Answer to question 16 Packing list Specification c ccccceeceeeeeeeeeeeeeeeeeeeeeeeeeeenes 17 Description of heating function 1 Heating function can be selected for STANDARD QUICK JEAN and POSTHASTE programs but it s unavailable for RINSE process 2 If heating function is selected for water levels 1 or 2 it begins to heat after water reaches the
7. ashing the woolen textiles WATER LEVEL button The washing machine can detect the laundries automatically After detection it will set the water level to suitable value among 4 6 8 and 10 automatically You can also set water level by yourself After the machine is started J it will not set water level automatically You shall push the start pause button to make new setting If there s water inside the tub the machine cannot detect the e laundries and will display water level 6 If wet laundries are put in it may display water level 10 You must set suitable water level by yourself e If POSTHASTE programs selected it will display water level 3 When water level 2 is reached in water filling it will perform washing while filling water When water level 3 is reached it will change to normal washing During operation of wash and rinse program you can push down the water level button to add water When you release the button or it reaches the overflow water level the machine will stop adding water b Steps o veng the operation buttons and description of the steps a A ae ee a we OSES we we o Unut ae eee POWER N Fu UzZzY o Bo ONOFF Tene ome Q ae nse S orto g z ooun Oe sen TART Six PAUSE ee l a 1 SOAK A i PROGRAM F WATERLEVEL 1 Push the POWER ON OFF button to switch on the power IL POWER ON OFF 2 Push the PROGRAM button to select s
8. ate Twist the fastening nut as per the indication of the figure to seal up the exit end face of the faucet See to Figure 5 remark Before installation the threading is 4mmabove the upper surface of the nut After installation the threading is 2mm above the upper surface of the nut see to figure 6 About 4mm before twisting About less than 2mm after twisting Figure 4 Figure 5 Figure 6 Connection between the water inlet hose and the washer 1 Do not take off the water absorption cushion Please check if the cushion is dropped or damaged before each usage If it happens nut of the water please contact our after sale department immediately inlet hose 2 Put the nut of the water inlet hose on the valve jointer 3 Fasten the nut Swing it gently to confirm if it s suitable jointer of the water absorption water inlet valve cushion Connection between the jointer of the water inlet hose and the water inlet hose 1 Push down the slider Insert the water inlet hose into the jointer the jointer of the water inlet hose 2 Hang the lock lever to the jointer Release the slider till a click Locking levei sound is heard Check the connection between the jointer of the water inlet hose and the water faucet 1 Swing the hose gently to confirm if it is fastened stable 2 After installation open the faucet to check if it leaks 3 Do not bend the hose with overstrain 4 Before each usage please check if the connection
9. ater It is to avoid splashing during water filling There may be some water flowing out of the drain hose in the first use of the machine It is the water remained in the performance inspection by the factory When the power plug is inserted computer board indicator is switched on and the machine starts working It is the special resume function In the case of power failure or the power plug is loose during washing the machine can save the running program and resume the program after the power supply is recobered You do not need to set the program again The actual heating temperature may have discrepancy with the setting level This is the normal phenomenon The actual heating temperature is also influenced by the atmosphere temperature the water temperature for wash and the water hardness 16 Packing list Name Quantity Storage position User s manual One Inside the document bag Warranty manual One Inside the document bag Components of the water inlet hose The end connecting to thewashing machine Jointer connecting the water ey hose and the waterfaucet The end connecting to thewater inlet hose jointer Water inlet hose 1 piece Water inlet hose joint 1 piece Inside the accessory bag Bottom plate 3 wey Between the upper cushion of the washing machine package and the upper seal of the package carton Tapp
10. eaches the position convenient for you to take it off Pull it up to dismount 2 Push it down to install 3 Clean the filter screen after washing n Ss Dismantle a Dismantle ra i L instal l A Dismantle Install The filter screen of the water inlet valve is likely to be If the cabinet is dirty wipe it with wet cloth blocked by foreign materials and influence the water Do not flush it directly with water inlet Wipe it with neutral detergent Please clean it with brush every two months e Do not wipe it with thinner petrol alcohol etc 1 After washing close the water faucet If needed you can dismantle the water inlet hose 2 Do not store water in the washing machine for a long period Drain the water completely after each using 3 Be sure to pull off the power plug before maintenance 4 Hang up the power cord and drain hose 5 Wipe off the water drops on the surface of the machine and inside the tub Open the top lid for some time about 1 hour then close the top lid 15 Trouble shooting Answer to question If there s breakdown please pull off the power plug before checking The following phenomena are not breakdowns sometimes Please confirm again before sending it to repair If there are real breakdowns please come to the special maintenance department or after sale service department of our company Do not repair it by yourself Phenomenan The digitron displays E0 The reason The
11. ee there are no dropping or abnormal sound in opening and closing of the inner cover and the operation shall be smooth Do not dismount the inner cover component after washing _ Outer tub cover Sa Outer tub cover shaft groove Kus Inner cover shaft 7 a CO 44 Inner cover component ETS Figure 2 Figure 1 Install the bottom plate After opening the package please lean the washing machine gently down on soft items like towel cloth blanket etc Install the bottom plate to the bottom of the machine with eight screws by a cross screw driver then lift the machine up gently See to the figure oe Bottom plate SS Soft items Screw Adjust the Installation position The largest allowable slope of the shank base of the machine is 1 The slanting or rough ground will result in unstable running or stoppage of the machine Please adjust it with following methods Confirm it s horizontal Hang the lead line to check if it is horizontal Adjust the adjustable leg 1 To twist the adjustable leg please first lift up the side of the leg slightly loosen the adjustable nut and twist the leg 2 Afteradjustment fasten the nut Usage the drain hose The drainage shall be smooth with the drain hose 4 If extra drain hose is needed please make separate 1 The height of the drain hose shall be less than purchase The inner diameter of the extra hose shall 10cm or the drainage will not be sm
12. infest color from other laundries c Put those laundries difficult to absorb water into water with hand d For those laundries with heavy soil please first remove the dirt like mud or dust For the parts with heavy soil please apply detergent in advance which can make it easier to remove the soil e For those laundries that may get lint ball and those with long fur turn it over before putting in f Do not put those laundries polluted by chemicals directly into the washing machine 2 Put in the laundries The capacity of washing of the machine refer to the largest weight of the standard laundries under dry condition that can be washed in one time Laundries quantity in one washing cycle shall be lower than the rated capacity The largest capacity of this machine is 6 0 kg The thickness size type of the cloth will influence the actual washing capacity It is suitable to put in reasonable amount of laundries and the laundries can be turned round in washing for one time washing Do not select the higher than 4 water level for laundries less than 1 0kg so as to avoid splashing of water 3 Put in the detergent Access for detergent and washing powder Access for softener ve How to use the whitener Fill water to decided level Dilute the whitener with container Pour it slowly into the washing tub Avoid using whitener on laundries with colour or pattern as they are prone to lose colour The wh
13. ing screws Inside the accessory bag Inner cover component Inside the accessory bag bd Fuzzy Computerized Automatic Washing Machine Specification Rated washing spinning capacity 6 0kg 6 0kg Water level Water quantity about W12L 2 16L 3 20L 4 25L 5 29L 6 33L 7 38L 8 42L 9 47L 10 50L Injection pressure 0 03MPa 0 78MPa 1 7
14. itener shall not touch the laundries directly Refer to the user s manual for the usage and quantity of the whitener For powder whitener please dissolve it before use Put the washing powder and softener into the detergent box directly as Indicated in the left figure After that please close the detergent box Refer to the following list for the usage of the detergent the standard dosage of the detergent and the water quantity How to use softener See to the manual of softener for the usage and dosage When adding softener into the softener inlet of washing powder box note that it shall not exceed the lower side of the cap Do not leave the softener for long period after adding itinto the box Otherwise it may be solidified and block the inlet As the softener is easy to solidify please clean the box frequently You shall clean it each time you use reserve function Before use softener you must select to sterilize function How to use the washing powder Directly dissolved in the machine not applicable for fuzzy program and reserve wash 1 Fill small quantity of water 2 Add the powder Run for 30 seconds to dissolve it completely 3 Put in the laundry Select suitable water level The instant dissolving of the washing powder 1 Prepare warm water of 30 C and a container 2 Add the powder while stirring to fully dissolve it In selecting The super quick program it is sugge
15. le is loose be sure to have it replaced by the technicians ofour special shop or our agent or the after sales service department to avoidany risk Keep the prong of the power plugclean If dust is foundon the power plug please wipeit off withdry cloth In case the washing machine is installed on ground Do not use water with temperature higher than 50 C with carpet be careful not to block the ventilation hole with carpet The ventilation holes at the bottom Soft items Do not put the machine at damp place like the Do not wash water proof laundry like the raincoat bathroom Never wash it with water Do not bike covers down textiles etc To avoid abnormal put wet laundries on the front control panel board Vibrations in spinning and damages to the laundries Do not let the machine share one receptacle with other electric appliances If the power plug is damaged or the plugging into the receptacle is loose do not use the plug any more S Safety precautions a Do not put hand into the rotating tub It is dangerous even if the rotation speed is slow Take special care of the children Keep children away from the washing machine to avoid them climbing on 9S Do not decompose repair or alter the machine by yourself Do not put any hot or heavy items such as the kettle with hot water on the washing machine e Do not wash laundry with volatile materials such as thinner petrol
16. ne have no reaction Digital tube During sensing it displays During operation of programs it displays the remained time minute or remained times of the corresponding procedure RINSE button Push the RINSE button to set the rinse and disinfect procedure During STANDARD and JEAN programs push the RINSE button to set different rinse times 0 1 2 3 4times During FIBER COTTON WOOLLEN and SILK programs push he RINSE button to select rinse procedure but the rinse times cannot change During QUICK POSTHASTE programs push the RINSE button the machine have no reaction During STANDARD program the machine is set to save water program If you push he rinse button before starting operation it will change to water storage rinse program 10 SPIN button Push the SPIN button to set the spin procedure During STANDARD and JEAN programs push the SPIN button to set different spin time from 0 to 9 minutes During FIBER COTTON WOOLLEN and SILK programs push the SPIN button to select spin procedure but the spin time cannot change During QUICK POSTHASTE programs push the SPIN button the machine have no reaction CHILD LOCK FUNCTION Push and hold the WATER LEVEL button and SPIN button then push down the POWER ON OFF button The digitron displays CL You can continue setting desired washing procedures Af
17. ogram for the woolen textiles Separate the laundries that are not colorfast from other laundries in washing The pulsator will not rotate unless the water is filled to 3 water level The soak procedure can work in cooperation with automatic programs like standard jeans fiber and cotton There is intermittent pulsator stirring during soak e After the machine starts operation you can only set the program and procedure during washing and can not make setting in other cases 4 Press WATER LEVEL button select suitable water level oe i WATER LEVEL After switching on the power the washing machine will execute fuzzy program automatically to detect the cloth After defection it can set the water level automatically To select other water level first push the START PAUSE button then push the WATER LEVEL button to set the water level Refer to water level button in Page 11 for selection 13 5 Push the RESERVE CALEFACTION button to select suitable reserve wash program RESERVE CALEFACTION After switching on the washing machine reserved wash programwill be automatically set inactive If you desire a washcycle to endat a reservedtime you can press the RESERVATION CALEFACTION button to seta reserved wash program Refer to The button of RESERVATION CALEFACTION on page 11 e Confirm the reserve program Page 11 ima When RESERVATION becomesactive the nixie tube displays thetime to the endof the
18. ooth and cost not less than 30mm and the length shall not exceed such long time that the machine may stop at mid 4 5m way 2 Do not step on or press the drain hose 3 If the drain hose is too long cut it at mid point To make 5 If the extra hose is too long cut smooth drainage cut the front end of the hose slantingly it either at A or at B point Install the water inlet hose Confirm the water faucet water faucet suitable water faucet not suitable The exit end face of the faucet It is required that the front end shall be longer than 10mm The exit end face of the faucet shall be flat and smooth If not please file it to avoid leakage Connection between the water inlet hose jointer and the water faucet 1 Press the lower end of the lock lever and push down the slider Take off the water inlet hose jointer from the water inlet hose component See to Figure 1 2 Loosen the screw till the water faucet can be accessed Put the jointer of the water inlet hose on the faucet See to Figure 2 If the faucet is too large and the jointer can not be set on the water faucet please loosen the four screws and take out the bushing in the jointer The front end of the faucet must be smooth otherwise it may leak water See to Figure 3 water inlet hose jointer Slider Screw knife PIa 5 Ly Bushing water inlet hose Figure 1 Figure 2 Figure 3 3 Fasten the four screws evenly See to Figure 4 4 Take off the namepl
19. r absorption cushion Inner tub Handle Front control board Cabinet Power cord N Base frame Drain hose Adjustable leg T aie Fixed leg 3 pieces oe Back cover Adjustable leg film Meaning and description of the symbols Warning sign Contents marked with that symbol are related to the safety gt of the product and the personal safety of the users Please operate in strict conformity to the contents otherwise it may cause damage of the machine or injure the personal safety of the user Forbidden sign Contents marked with that symbol are actions forbidden to perform Performing of those actions may result in damage of the machine or injure the personal safety of the user is i Safety precautions In normal usage of the washing machine the power Please plug the plug on special 220V AC receptacle plug shall be ready to be pulled or plugged with hang Be sure to use single phase three pins receptacle Be sure to pull the plug off and close the water faucet Ensure the earthing prong of the power receptacle is when occurring power failure delivering the maching earthed reliably Use leakage protector if possible setting the machine idle or cleaning the machine do not plug or pull the power plug with wet hand WD Do not bend stretch twist bind the power cord by force or reform it Do not pressor clamp it with heavy items If the power cord and power plug are bad or the receptac
20. set level and begins to wash when the set temperature is reached for water levels 3 6 itbegins to heat upon water reaching level 2 it continues water supply and gently agitates while heating to the set temperature then it begins STANDARD washing for waterlevels above 6 the cycle is after water reaching level 2 it begins to heat meanwhile water supply continues until level 6 water supply stops and it continues heating to the set temperature then it begins to wash while water supply is resuming the hot water temperature then is good for detergent active enzyme function and for the clothes to bein an optimum detergent concentration witha good washing effect The subsequent washing while water supply can facilitate dirt flushing and removing water supply stops when reaching the set level then it continues to wash STANDARDly For high water levels only the water amount below level 6 can be heated to the set temperature then it washes and supplements water to the set level 3 This washing machine provides 3 temperature selections of 20 C 30 Cand 40 C Names of the parts Top lid component Inner cover component Detergent box liquid whitener inlet Control panel Outer tub cover Balance ring Top lid handle Round cover Attachment block 2 pieces Pulsator Water inlet valve Lint Filter Wate
21. sted to adopt liquid detergent instead of washing powder to guarantee the washing effect The powder is more prone to pollute the laundry than the detergent Therefore please use it with suitable quantity It is suggested not to use high sudsing detergent Washing powder with poor quality or long time storage maybe caked Please pay attention to cleaning the detergent box in time 4 Use the operation buttons a Description of the function of buttons Mode and meaning of the indicators Flashing indicate the running program On indicate the program about to run or indicate the selected mode SOAK button Push the SOAK button to set he soak procedure During STANDARD and JEAN programs push the SOAK button to set different soak time 10 20 30 40 minutes During FIBER and COTTON programs push he soak button to select soak procedure but the soak time cannot change During QUICK POSTHASTE WOOLLEN and SILK programs push the SOAK button the machine have no reaction WASH button Push the WASH button to set the wash procedure During STANDARD and JEAN programs push the wash button to set different wash time from 0 to 25 minutes During FIBER COTTON WOOLLEN and SILK programs push the WASH button to select wash procedure but the wash time cannot change During QUICK POSTHASTE programs push the wash button the machi
22. ter setting push down the START PAUSE button The child lock function is activated All of the buttons are locked and cannot make selection Release the child lock function push down the WATER LEVEL and SPIN button at the same time for more than 1 second After a beep sound the child lock function is released Push the ON OFF button to switch POWER ON OFF button on the power When the power is on push it again to switch off the power Push the ON OFF button to switch RESERVE REMAIN time indicator digitron During sensing it displays During reserve procedure it displays the remained reserve time in hours During operation of programs it displays the remained time minutes If the remained time exceeds 99 minutes it adopts A at tens place to represent 100 minutes b to represent 110 minutes For instance A3 represents 103 minutes In case of abnormal phenomenon it displays the abnormal symbol see to Page 16 Time HER EN y minutes Ora Tater D RESERVE CALEFACTION Wi RESERVATION CALEFACTION button Press RESERVATION CALEFACTION button to set reservation or heating Function During machine running thedigitron indicates the cycle remaining time in minutes Press RESERVATION CALEFACTION button the digitron willlndicate the remaining reserved time tocycle end in hours Thedigitron will indicate the runningstate of the machine Heating function can beselected if
23. top lid is opened during reserve procedure How to settle Close the top lid The drainage cannot work or is too slow The digitron displays E1 Is the drain hose put down Is the drain hose blocked Put down the drain hose Open and close the top lid once Clean the foreign material Open and close the top Lid Once It stops running in midway The digitron displays E2 The top lid is not closed Close the top lid The safety switch acts and the spinning cannot work The digitron displays E3 Are the laundries put slantingly Is the machine slanting Reorder the laundries Close the top lid The machine will start running after 10 seconds of being placed horizontally The water filling does not work or is slow After about 40 minutes later the digital displays E4 Is the water tap opened or is there water supply failure Is the water inlet valve blocked Is the water pressure too low Open the water tap Push the Start Pause button once Clean the water inlet valve then push the Start Pause button once Push the Start Pause button once The digitron displays E5 The temperature sensor is fallen Please contact the after sales service department The digitron displays E6 The water level sensor is bad Please contact the after sales service department The digitron displays F5 The water level drops to the replacement point
24. uitable automatic program E PROGRAM After switching on the power the machine will set STANDARD program automatically To select other automatic program push the PROGRAM button till the relative indicator is on Refer to the PROGRAM button on Page 11 for the selection For instance select POSTHASTE program for laundries with small quantity and light soil In selecting the e e e e e e e program the machine will execute fuzzy program to select water and wash FIBER O STANDARD time according to the cloth and weight of the O COTTON Oo QUICK laundries The full procedure is controlled wooLLEN POSTHASTE automatically sik Jean 3 Push the SOAK WASH RINSE OR SPIN button to select suitable procedure 12 After switching on the power the washing machine will set to common program including wash rinse spin automatically To sdect other procedures push the SOAK WASH RINSE or SPIN button to select the time of soak wash and spin and the times of rinse After switching on the power if you push one of the button among WASH RINSE and SPIN the digitron of the former procedures will turn off automatically The former procedures will not run For instance after switching on the power If you push the SPIN button first it will execute spin singly after starting Even there s no water in the tub a certain period is required before spin starting Donotuse the soak pr
Download Pdf Manuals
Related Search