User Manual
Contents
1. are connected to the OUT reader for exit inside the premises Pressing the bypass switch or presenting the authorized cards will release the strike Clocked data will be sent from both the IN and OUT reader to Time Logger s database if connection is good Outside for Entrance Wiring Illustration Slave Reader Set u Jumper setup for slave 12V tol 2V amp G6 toG 4 o EE A i lt _Z TO ELECTRIC LOCK Q J m E T _Z 10 POWER 9 12V 600mA Q x J _z TO BYPASS SWITCH Inside for Exit D RX TX GND INI IN2 OUT 12V 12V G LOCK G NO COM NC X TX to RX amp RX to TX pe Chey TO COMPUTER see section 4 Terminal Layout for wiring instruction Master Reader Set u Sefup the jumper blocks according to section 3 ae Setup the MASTER amp ACTION card from the master reader in Time Logger OUT Use the ACTION CARD to authorize the ID cards Mode of operation in Setup Reader C CLOCK Mode Single reader all logged records will be stamped as clock entries 2 QUICK START 2 1 Configuring the jumper blocks according to your needs see section 3 2 2 Set up your MASTER and ACTION card according to appendix A section 1 Remember to remove the CLRM jumper after setting up the MASTER and ACTION card 2 3 Remove all authorized key card see appendix A section 4 Present an authorized card to the TL2730U the green LED and relay will turn on as set by TMRO TMR1 and TMR2 with a be2. the MASTER and ACTION card memory TMR2 TMR1 TMRO FUNCTION OFF OFF OFF Relay on for 1 second on authorization granted OFF OFF ON Relay on for 2 seconds on authorization granted OFF ON OFF Relay on for 5 seconds on authorization granted OFF ON ON Relay on for 10 seconds on authorization granted ON OFF OFF Relay on for 20 seconds on authorization granted ON OFF ON Relay on for 50 seconds on authorization granted ON ON OFF Relay on for 100 seconds on authorization granted ON ON ON Relay state is toggled on each authorization granted ON Jumper shorted OFF Jumper opened T a ae 222220 NS CU Jumper setting for 7 slave reader oo E 4 DIMENSIONS AND TERMINAL LAYOUT Dimensions J One mounting holes of diameter 5mm 10mm 20mm 86mm ll gt i Three mounting holes of diameter 4mm E E O CO Vv Front View side View Rear View Terminal Layout a LLI Tp pepe Ua NORMAL CLOSE o COMMON RELAY Te NORMAL OPEN ND TO ELECTRIC LOCK Sc OUT GND 9 12 300mA DC IN OPEN SW BYPASS SWITCH GND DATA TO PC DB9 PIN 2 5 DATA FROM PC DB9 PIN 3 s GND DB9 PIN 5
3. TL2730U QuickProx Standalone Access Controller for 2 30 ID cards including Master amp Action Card Time Logger User Manual V1 0 1 INTRODUCTION The TL2730U proximity access controller is a cost effective solution for 2 728 users for access control and time recording A 9 to 12V DC supply is required to power the reader which has a current consumption of less than 300mA 600mA for dual reader There are three modes of operation in Setup Reader COM1 VEA s Reader Options WV Reader is connected A IN Mode Single reader use TL2730U for entrance ee _ PC based TIME LOGGER with PC ON aaa T a For audit trail and attendance reports Corim Cancel bw In this mode only a single controller is installed outside the premises An Electric strike can be connected A bypass switch is installed inside the premises pressing it will release the strike While connecting the TL2730U s RS232 port to the computer and running the Time Logger software Windows the program will stamp the clocked date time and card ID into the computer database and show up the associated picture with the specific ID on the computer screen for attendance reports B OUT Mode Dual reader use a TL2730U for Entrance another TL2730U for Exit PC based TIME LOGGER with PC ON In this mode one TL2730U is installed outside the premises for entrance Another TL2730U is installed inside the premises for exit An electric strike and a bypass switch
4. ep sound On the other hand if an unauthorized card is presented to the TL2 730U the green LED and the relay will have no action but with a long beep sound An input contacts is provided if it is shorted the unit will respond the same as an authorized card read Goto 2 6 if use the Time Logger for granting authorization keeping card information and reporting See section 3 5 and 4 2 in Time Logger s User Manual for details 2 4 Use the ACTION card to authorize the ID cards see appendix A section 3 2 5 Record the authorized ID card number and the associated personnel This is for removing the authorized card number in case of card losing 2 6 Power off the reader 2 7 Connect the RS232 cable straight through from the computer to the terminal block of RS232 port See Terminal Layout 2 8 Power on the reader 2 9 Turn on the computer 2 10 Insert the Time Logger CD into your computer s CD ROM drive The Installer will start by itself automatically If the Installer doesn t start automatically you can run the setup exe program to install the software 2 11 The detailed installation manual for the Time Logger will be automatically installed into your computer when you install the application software Follow the installation instruction to finish the installation and follow the Installation Manual of Time Logger from Start for details of Time Logger s Setup Installation Manual of Time Logger from Start Manal
5. fF Time Logger 4 Favorites SS Documents amp Settings A Find amp Help ZI Run amp Log Off RY Shut Down Start 5 hae gy Time Logger r Time Logger Quick Start 5 Insert the CD ROM to the computer to ADD Cards 6 Uploading the and Edit Card Information authorization table to the reader Time Logger Sele Actions Database Setup Card 2 Login the Time Logger to start SETUP G Logout Edit Card Information net Password g Print Cards 1 Setup the password eJ i ae Hide to systray d Print Member List for LOGIN first fl Erit About Time Logger 4 Define the workgroup Group Definition 3 Setup the RFID reader Readers Present the ID cards fo the reader if the com port set up correctly the record will be shown on the screen Offline Reader Manager Hide On Startip 4 tacord s a 4ug 18 2005 Thu PM 03 10 51 273357 OUT Entance DENIED Aug 18 2005 Thu PM 03 11 21 367563 IT Entrance DENIED Aug 18 2005 Thu PM 03 11 28 373357 DUT Entance DENIED Aug 18 2005 Thu PM 03 11 30 373357 IN Entrance DENIED hl l fAug2005 Tho PM 03 45 07 3 JUMPER SETTING There is a 5 position jumper block for configuring the operation of the unit JUMPER POSITION FUNCTION TMR2 TMR1 To select the relay on time with authorization granted TMRO RVSE ON to reverse the operation of the relay CLRM ON to clear
Download Pdf Manuals
Related Search