JA-63 „Profi“ User manual
Contents
1. 00 if left disarmed Automatic disarming is also programmable See part 4 4 for details Fast arming without access code can be disabled by the installer The JA 60F battery powered wireless keypad will stop indications 10sec after the most recent key entry Alarm system JA 63 Profi 5 MGK51504 3 2 Disarming On the keypad enter your user code On the remote control RC 4x press the G button e system will beep twice e if there are 3 beeps important information is indicated and will be displayed on the keypad Examples o FAILURE LED is flashing press the N key to view the cause o ALARM LED and zone number is flashing alarm in the memory Be careful and check the house e if you enter the premises when the system is armed the entrance delay countdown will start after you trigger a delayed detector ARM LED will flash and beeps will sound if programmed so 3 3 Panic Alarm If you are in danger you can trigger the silent panic alarm to inconspicuously call for help While in Panic alarm mode the control panel can send a voice message an SMS message and data to a central monitoring station via a telephone line depends on installation settings Panic alarm can be triggered e On the keypad press the panic key and then enter your Tr access code ee On the remote control RC 4x press the and 6 buttons simultaneously The remote control can be switched by installer to a Panic mode in whi2. and disarmed separately by their own codes and remote controls or if the main control panel will rule the sub control panel Ask your installer for explanation on how to operate your system if a sub control is panel installed 3 10 Appliance control The system can be used to control an electrical appliance light heating ventilation etc In such a case users can operate the device Locally with keypad entering F81 ON or F80 OFF Remotely by phone keypad or by SMS messages the control panel must be equipped with GSM communicator for this feature Installer can program that this feature will work only when the entry is followed by a user code 4 User s settings Following section is designated for the system supervisor who knows the master code All programming sequences can be terminated before completed by N key 4 1 New master code The master code is used by the supervisor The factory default master code is 1234 and you should program your own four digits code Code programming is only possible when the system is disarmed To change an existing master code enter F 5 xxxx yyyy Yyyy where xxxx is the existing and yyyy is the new master code new code must be entered twice to avoid an error Example Existing code 1234 will change to 6723 entering F 5 1234 6723 6723 Alarm system JA 63 Profi 8 MGK51504 4 2 User codes setting There can be up to 14 different user codes for individual use
3. codes are empty as a factory default and should be programmed by the supervisor see section 4 2 Alarm system JA 63 Profi 4 MGK51504 Master code Is an extra 15 access code for the supervisor It can operate the system and it also allows for the programming of the other user codes and to enter the user mode see section 4 Factory default master code is 1234 The supervisor should change it after installation Service code Is an extra code used by the installer to enter the programming mode End users are not usually told this code If an invalid access code is entered more than four times in a given period of time it will trigger a Tamper alarm on the control panel 3 1 Arming On the keypad enter your user code or press the fast arming button On the remote control RC 4x press the button e system will beep once and the exit delay countdown will start e ARMED indicator will flash during exit delay e you should leave the protected area within the duration of the exit delay If there are 4 beeps while arming the system is indicating an unusual situation and the keypad will display the specific information ALARM and a zone number the zone is not ready opened door etc check the indicated item b some detectors are bypassed done by supervisor see part 4 5 Note supervisor can program an automatic arming for a desired time for example the house will be armed automatically at 21
4. conditions of this Limited warranty Jablotron Ltd warrants this product to be free from defects in design material and workmanship at the time of its original purchase by a customer for a subsequent period of two 2 years Should your Product need warranty service please return it to the dealer from whom it was purchased Conditions 1 The warranty is valid only if the original receipt issued to the original purchaser by the dealer specifying the date of purchase is presented with the Product to be repaired or replaced Jablotron reserves the right to refuse warranty service if this information has been removed or changed 2 This warranty does not cover any failure of the Product due to misuse including but not limited to use in other than the normal and customary manner in accordance with instructions for use and maintenance of the Product Nor does this warranty cover any failure of the product due to accident modification adjustment improper repair or acts of God 3 This warranty does not apply to batteries nor modules of other suppliers e g SIM card of the GSM provider 4 The warranty provided does not affect the consumers statutory rights under applicable national legislation in force nor the consumer s rights against the dealer arising from their sales purchase contract Alarm system JA 63 Profi 2 MGK51504 Note features of this system can be substantially modified by programming during installation The
5. system JA 63 Profi 15 MGK51504 Notes Alarm system JA 63 Profi JABLOTRON CREATING ALARMS JABLOTRON ALARMS a s Pod Skalkou 4567 33 46601 Jablonec nad Nisou Czech Republic Tel 420 483 559 911 Fax 420 483 559 993 Internet www jablotron com 16 MGK51504
6. JA 63 Profi User manual Contents ONO Limited waran iVe e a aran eaa eae aaaea erae ae p aaae apartada aeaaea Aaaa aea aaar an EEan aan aaa Aaaa IndicatorS 1 2111111111111111 Controlling the system 3 1 Arming 21112 112212 3 2 Disarming 3 3 Panic Alarm 3 4 To stop ALARM 3 5 Home arming 3 6 Door opening See ORA SP 3 7 Alarm memory reading rss aen plane EP PIE AO A PERE 3 8 Split syste iarMing ei Ad A NEW A sential A WO A RA SE R a 3 9 Subsystem arming 3 10 Appliance control User s settings gt 4 1 New master code iin dza r RE AEO REA RO A aA EE ERa PARANA ns 4 2 User COdESSOUING ei EA AR ARA ER A ann Ad a deci avers EA 4 3 Internal clock setting 4 4 Automatic arming disarming 4 5 BYDASS we awe A tees m Digital communicator 22 em se nesneneaneaana aaa ana adta aea aKa ia pan aan aaa aa ana awa tanaan epea aaa ANA 5 1 JA 60GSM Dialer MOGUIC ccccccccccssccessseceesseeccesseeccsseecceseeecessseeccssaeeceseeceseseceseeeessaes 5 2 JA 65X Telephone communicator 2211211 5 2 1 Telephone numbers for voice message sending 5 2 2 Telephone communicator testing System teStiNg zzz a a aaa ea Battery replacement se Eee Enrollment of the control panel to UC 2xx modules 1 css eres Limited warranty Subject to the
7. are recorded into the control panel s memory along with the time and date The complete system history can be viewed using a PC with Comlink software Alarms and failures can also be viewed on the keypad by entering F 4 will show the last recorded alarm or failure Press key 4 multiple times to go deeper in to the memory 3 8 Split system arming The system can be split by the installer into two independent sections A B and a shared section corridors stairs a main door This allows for a particular user to arm and disarm only a particular section of the house with his her code or remote control exactly as in a non split system Arming of sections A and B is indicated by I I symbols on the keypad The shared section will be armed automatically when A and B sections are both armed With the master code the supervisor can arm and disarm both sections If the master code is entered the system will arm if completely disarmed or disarm if any section is armed Entering F1 master code will control only section A and F2 master code only section B this is true only when fast arming is disabled by the installer Note partial Home arming is not possible if the system is split Alarm system JA 63 Profi f MGK51504 3 9 Subsystem arming In a large building a sub control panel can be enrolled to the JA 63 The subsystem reports all alarms and failures to the main system The installer can program if the systems will be armed
8. ch pressing of any button will trigger the Panic alarm e By pressing this large sized panic button the RC 22 can be installed on the wall under a desk etc 3 4 To stop ALARM If an alarm is triggered when you are present you can stop it by entering your access code or by pressing button o on the remote control e Sending of voice and SMS messages will cease after the alarm is stopped All corresponding report codes alarm triggering amp stopping will be sent to the central monitoring station e f user does not stop the alarm it will stop automatically after the programmed period and the alarm memory indicator will activate The control panel will return to the same mode as before the alarm Alarm system JA 63 Profi 6 MGK51504 3 5 Home arming The installer can program particular detectors so that they will be automatically bypassed in the so called Home partial arming This allows for people to stay in the particular part of the house after arming To arm partially e On the keypad press home arming button H will indicate the Home partial arming on the keypad To disarm a partially armed system enter your user code or press the or O button on the remote control 3 6 Door opening An electrical door lock if installed can be controlled via the alarm system e Press the door opening button on the keypad to release the 3 7 Alarm memory reading All events arming disarming alarms failures
9. ge the arming e Factory default setting all instructions are set for no action To exit user mode press the N key 4 5 Bypass The supervisor can bypass switch off particular zones potential sources of alarms while in the user mode If a zone is bypassed it can t trigger an alarm To switch the control panel to the user mode enter F 0 master code User mode will be indicated by a U on the keypad To set up bypass 1 Press key 1 to open the bypass menu 2 With key 1 and 7 you can scroll all potential alarm sources wireless detectors are distinguished with the symbol 9 3 Select the source detector wired input which you want to bypass and a either press key 2 for 2 seconds to bypass the source for the next arming period confirmed by flashing Battery LED b or press key 3 for 2 seconds to bypass the source permanently confirmed by the Battery LED being permanently lit Alarm system JA 63 Profi 10 MGK51504 c multiple pressing and holding of the keys 2 or 3 will switch the bypass on off on off 4 By repeating step 3 you can bypass all required alarm sources To close the Bypass menu press the N key If anything is bypassed when arming four beeps will sound and b will be displayed on the keypad during the exit delay and partial arming will be recorded to the memory All bypasses selected with key 2 next arming period bypasses will switch off automatically with the first following di
10. he control panel l indicated event Tamper Failure or Battery wretesssren was caused by the outdoor wireless siren Sub control indicated event Alarm Tamper Failure or panel Battery was caused by the sub control panel Alarm system JA 63 Profi 3 MGK51504 indicated event Tamper or Failure was caused by the telephone line indicated event Tamper or Failure was caused d digital bus by a device keypad or PC connected to the digital bus Telephone line communication wireless keypad lost connection with the control failure panel error self testing error call installer tab 1 88 display specifies mode of the control panel authorized supervisor can test bypass zones change user mode batteries record voice messages program tel numbers and adjust internal clock in this mode C eme emeen C ea eenma arming AA key pressed waiting for more data to complete the entry cl programming i i i tab 2 3 Controlling the system The system can by controlled by keypads remote controls or by a PC with the Comlink Software User codes Can be used to arm and disarm the system or to reset an alarm There can be up to 14 different user codes for individual users The system stores to its memory which code was used for which operation as well as the time amp date of usage This data can go to a Central monitoring station and can also be viewed using a PC with Comlink software All user
11. installer should instruct the users how to operate and test the system 2 Indicators The alarm system s status is indicated on the keypad There can be multiple keypads in the system and in such a case all keypads will have identical functions A keypad s LED indicators and display inform the user about the conditions of the system LED indicators COMFORT Alarm alarm triggered by an intruder smoke gas etc Tamper opened cover damaged detector excessive number of attempts to enter code etc ein Fault power loss lost communication with a detector etc view details by pressing N ZSALL34 Battery battery of the device specified on the display is low See battery replacement section information received from a wireless item or wireless communication of the keypad in progress Armed continues armed slow blinking exit delay fast blinking entrance delay SYSTEM JA 60 Power coniinues AC power 8 back up battery O K blinking failure AC or back up battery off control panel is not powered 88 UD specifies event source es wireless indicated event Alarm Tamper Failure or c detector 12 Battery was caused by detector number 12 indicated event Alarm Tamper Failure or ee Battery was Ra by wired zone number 2 wireless indicated event was caused by wireless w controller remote control keypad Panic button controller 3 number 3 indicated event Tamper or Failure was caused canualipene by t
12. line signals Alarm system JA 63 Profi 11 MGK51504 Example to store tel number 0 123456 to memory no 2 enter 7 0 FO 12345 F2 To delete a telephone number enter 7 FO Fy where y is a memory number from 1 to 4 To exit user mode press the N key 5 2 2 Telephone communicator testing Testing is possible in the user mode To switch the control panel to the user mode enter F 0 master code User mode will be indicated by a U on the keypad Entering 89 will cause the communicator to send voice message number 2 to all programmed telephone numbers It will also send an SMS message if programmed The telephone line signals will be audible from the control panel s built in speaker during the test if the dialer is triggered by an alarm in normal operation it will call silently Testing can be terminated with the N key Notify the people who will be called before testing To exit user mode press the N key 6 System testing The supervisor should test the system monthly For testing the control panel should be in the user mode Enter FO master code to switch to the user mode U will be indicated on the keypad No alarm can be triggered while in the user mode and any triggering of a detector a remote control or a panic button will be indicated on the keypad Note some detectors for example the wireless motion detector in normal mode can not send the next triggering information until 5 minutes after the previous triggering wa
13. llment of the control panel to UC 2xx modules The wireless control panel can send data to UC 216 UC 222 and UC 260 output modules To enroll the JA 63 control panel to the UC 2xx switch the control panel to the user mode entering FO master code switch the UC 2xx to learning mode see its manual enter 299 on the alarm system keypad the control panel will enroll press the N key on the keypad to exit User mode Alarm system JA 63 Profi 13 MGK51504 code index User codes and controllers user name section A B notes o Master code supervisor 9 N o a R GIN _ e m m p _ Q _ gt o mk O N O o o R o Q o o N Q Telephone communicator setting memory calling to tel number notes 1 A Pein Pager Timers exit delay sec entrance delay sec alarm duraton min Notes Alarm system JA 63 Profi MGK51504 Detectors detectors section position location in the house reaction _ ____ type A B S a ao WIRELESS DETECTORS fee a _ a ae a oe a a _ WIRED INPUTS instant D delayed F fire P panic T tamper N next delayed Alarm
14. rs The system stores to its memory which code was used for what event and when This data can go to a Central monitoring station as well and can also be viewed by a PC with Comlink software All user codes are empty as a factory default and the supervisor should program them entering F 6 XXxx yy zzzz where xxxx is the master code yy is the user code index from 01 to 14 and zzzz is the new user code Example If the master code is 1234 and the user 3 new code should be 5277 enter F 6 1234 03 5277 To delete a particular user code enter 0000 as the new code combination 0000 can not be used as a valid code Example If the master code is 1234 the user 3 code can be deleted by F 6 1234 03 0000 Notes e You can program new codes only when the system is disarmed e The supervisor should record the codes to the table on last page of this manual it should be kept hidden in a safe place e If the system is split the supervisor can change the user codes but can not change to which section the particular code belongs only the installer can change this 4 3 Internal clock setting The control panel has a built in real time clock All events are stored to the event memory including the time amp date The clock should be set after installation but the supervisor can set the clock while in the user mode To switch the control panel to the user mode enter F 0 master code User mode will be indicated by a U on the keypad To se
15. s sent It is possible to switch such a detector to the testing mode by opening and closing its cover See the particular product manual for more details If anything does not work during testing call the installer To exit user mode press N 7 Battery replacement All the battery powered items perform regular battery testing If the lifetime of the battery is near the end the system will indicate the need for battery replacement Battery indicator and the item address will be shown on the keypad When any detector or keypad asks for new batteries they should be replaced in a week To replace batteries either call the installer or do the following e switch the control panel to the user mode entering FO master code Alarm system JA 63 Profi 12 MGK51504 open the cover of the detector keypad replace its batteries with new ones use only corresponding size and good quality alkaline batteries Wait for approximately 20 seconds before inserting batteries close the device s cover and test its function to exit User mode press the N key on the keypad Note normal battery life in wireless items is about 1 year Exposure to a very cold temperature frequent triggering or low initial battery capacity can shorten the battery life Recommendations the system should be annually inspected by a professional installer The control panel and the outdoor siren back up batteries should be replaced with new ones after 5 years 8 Enro
16. sarming e The existing bypass setting can be checked or modified in the bypass menu All bypasses can be deleted by key 4 in the bypass menu They can also be deleted by the programming mode opening or if the control panel is disconnected from the power completely AC amp back up battery To exit user mode press N 5 Digital communicator 5 1 JA 60GSM Dialer module If the control panel is equipped with a JA 60GSM communicator please look at the JA 60GSM user manual for details about user s setting 5 2 JA 65X Telephone communicator If the control panel is equipped with a JA 65X telephone communicator and if the installer enabled the supervisor to modify the communications settings only then will the following programming be possible 5 2 1 Telephone numbers for voice message sending Up to 4 telephone numbers can be programmed in the user mode To switch the control panel to the user mode enter F 0 master code User mode will be indicated by a U on the keypad Store telephone numbers for voice message by entering 7 XX XX Fy where xx XX telephone number y memory number from 1 to 4 A telephone number can have a maximum of 16 digits A dialing pause can be entered with FO Note enter a pause FO after the last digit of a number which is calling a mobile phone This way the number will be called only once and the dialer will not check the line signals some mobile phone systems do not generate standard telephone
17. t the clock enter 4 hhmmDDMM YY where hh hours mm minutes DD day MM month and YY year Example at 21 30 on March 19 2005 enter 4 21301903 04 To exit user mode press N Alarm system JA 63 Profi 9 MGK51504 4 4 Automatic arming disarming The system can automatically arm and disarm for a requested period of a day While in the user more up to ten instructions time 8 action can be programmed in the period of one day To switch the control panel to the user mode enter F 0 master code User mode will be indicated by a U on the keypad To program automatic arming enter 64 nahh mm Actions table a no splitting split where n instruction number from 0 to 9 no action no action a action see the actions table arm all arm all hh hours from 00 to 23 disarm disarm all mm minutes from 00 to 59 partial arming arm A Example to program an automatic complete disarm disarm A 1 2 3 4 partial arming arm B 5 6 arming of the system at 21 15 everyday disarm disarm B enter 64 0 1 21 15 Notes e fany automatic action is selected it will be preformed everyday at the programmed time following the internal control panel clock e The automatic arming and disarming can be overridden manually anytime by a user code or a remote control e Ifthe control panel is in the requested arming mode before the action time the programmed action will not chan
Download Pdf Manuals
Related Search