Gateway EnOcean/LonWorks RXZ95.1
Contents
1. 16 20 Siemens Building Technologies Impact on the system TO T1 T2 T3 All temperatures 0 0 C after Power fail Power up Room unit sends current temperature after about 20 to 30 minutes RXC polls the gateway 0 0 C and sends value to the system Frost alarm 0 0 C This state continues until all EnOcean room units have transmitted a valid temperature This takes about 20 to 30 min but may take longer than an hour should short breakdowns occur If a room unit does not send e g exhausted frost alarm is maintained until that room unit sends as well With each simultaneous power failure of the RXC and the gateway the system triggers frost alarm for 20 to 30 minutes The same applies to power up CM2N1661en 03 RXZ95 1 LON Gateway EnOcean LonWorks 2012 08 20 Sources of errors Mounting Notes for the radio reception Commissioning EnOcean connection LonWorks commissioning Disposal E Siemens Building Technologies The devices are supplied in an operational status Installation is made by means of anchors and screws not included to the smooth wall surface or by means of screws to an installation socket For operation a separate external 868 MHz receiving antenna is required included in delivery e The antenna with magnet foot should be mounted on the center of a 180 mm x 180 mm metal plate galvanized sheet steel e n rooms the antenna should be mounted 1 m below the2. Sensor 4 Sensor 5 nviLeamsSensar k 040 0 0 0 0 0 0 0 D 0 0 D D 0 E E nviRiequest O AG_NORMAL E nyo lam ensor 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 nvaFileDirectory 4002 nvoStatus 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Automatic Update When the learn telegram is received bit 0 is automatically reset Additional room units Repeat procedure set bit 1 1 to learn in Sensor 1 set bit 2 1 to learn in Sensor 2 etc 14 Function check gateway room unit SRCA 16 1 01 PluginDevice 6 E x Location Sica Description Default Device N s CPs Device i J rviMultiOut 1 Fb 1 nnn EnviMultiQut 2 Fb 1 nnn EnvoHVAETemp 1 2530 iE iE iE SHCA 16 1 l Made bject Sensor Sensar 1 Sensor Sensor 3 Sensar 4 Sensar 5 Senzor Sensors Sensors Sensar 3 Sensar 10 Sensar 11 Sensar 12 Sensor 13 Sensor 4 Sensar 15 El Automatic Update Update All Close nivoldultiiut 1 1 SET OFF 0 0 0 00 nvoldultiiut 2 1 SET FF 0 0 0 00 nvaSetpaint 1 342 nvoHVACTemp 1 Receive room temperature from room unit nvoSetpoint 1 Receive setpoint offset from room unit 14 20 Siemens RXZ95 1 LON Gateway EnOcean LonWorks CM2N1661en 03 Building Technologies Workflow with RXT10 and SBT generic plug in 2012 08 20 Sources of errors o eo eo N e
3. connection to the network see step 10 SCPTmaxSendTime Heartbeat room unit Recommendation Same as RXC gt Default 2700 s 45 min Note relating to SCPTmaxSendTime With the default setting of 0 0 s OFF and in the event the RF link breaks down faults no light etc the temperature value in the RXC will change to invalid when the heartbeat has elapsed When using a setting greater than 0 0 s the temperature value received last will be transmitted 6 gt Apply Question transmit to device Answer with YES Network gt Disconnect Attached offnet T Make RXT10 bindings Datapoint Gateway RXC Room Temperature nvoHVACTemp x nviSpaceTemp Setpoint Offnet nvoSetpoint x gt nviSetpointOffset Network Connect online Assign devices and install RXZ95 1 LON Gateway EnOcean LonWorks CM2N1661en 03 Workflow with RXT10 and LNS plug in 2012 08 20 Step Procedure 10 Learn in the room units Open Plug in Device gt Configure gt ThermokonLNSPlugln Device Configuration gt OK gt YES Click button next to SensorlD gt Learn in gt Press button on the room unit i Thermokon Sens a Ei x E File Extra Help Learn in r Sensor O 0 Please press learn in button at the sensor amp Sensor 1 iversal Temperature sensor ORG 7 Sensor 2 iversal temperature range with SCPTminRnge anc iy Sensor 3 Result 81 73 36 4 Sensor 4 Sensor ID 00 81 73 36 Sensor 5 DO amp S
4. F1 Gateway receives no telegrams from the room unit F2 RXC receives no LONWORKS telegrams from the gateway Siemens Building Technologies nvoHVAC Temp nvi nvoSpace Temp TR Possible causes gt Room unit exhausted gt poor light conditions Check documentation on room unit gt RF link faulty gt distance interference emitters Check documentation on room unit gt Room unit not incorrectly learned in in the gateway SensorlD gt Room unit faulty Impact on the system When UCPTenoceanRcvTm has elapsed nvoAlarmSensor is set evaluation optional TO T1 Last valid value from TO otherwise 0 0 C T2 With SCPTmaxSendTime gt T1 Without SCPTmaxSendTime gt invalid 327 7 C after RXC heartbeat has elapsed 60 min T3 Ditto if 0 0 C gt frost alarm Possible causes Gateway has no power power fail Bus interruption Error in configuration of gateway Gateway faulty GUD Impact on the system TO T1 T2 Invalid 827 7 C after RXC heartbeat has elapsed 60 min power fail gateway nvo temp p 0 0 C until room unit sends again up to approx 20 min Ohne SCPTmaxSendTime gt T2 last valid T2 SCPTmaxSendTime lt approx 20 min T2 0 0 C frost alarm SCPTmaxSendTime gt approx 30 min T2 last valid T2 T3 Ditto at 0 0 C gt frost alarm 15 20 RXZ95 1 LON Gateway EnOcean LonWorks CM2N1661en 03 Sources of errors 2012 08 20 F10 Power up Power fail system
5. ceiling e The antenna should be vertically aligned downwards e Minimal distance to the wall 90 mm e Distance to other transmitters e g GSM DECT wireless LAN EnOcean etc min 2 m e The antenna cable shall be routed in an electric conduit e Avoid crushing of the antenna cable The minimal bend radius of the cable is 50mm e Asfor the cable installation avoid the use of an active pull up device otherwise the sheathing or on the connectors may damaged For details on positioning of the EnOcean room units refer to data sheet CM2N1660 Wireless room units are sending time or event controlled telegrams to the gateway The gateway verifies the incoming telegrams and outputs them directly via its LONWORKS interface Each telegram allows a precise allocation and consists of the format type of the telegram data sender ID 32bit In order to assure a correct evaluation of the measuring values by the gateway it is necessary to have the devices learned in by the gateway This is done automati cally by means of a learn button at the room unit or manually by input of the 32bit sensor ID and a special learning procedure between room unit and gateway For details refer to the data sheet of the EnOcean room units CM2N 1660 In order to press the service pin the lid must be opened The device is classified as waste electronic equipment in terms of the European Directive 2002 96 EC WEEE and should not be disposed of
6. vC E D z D EC countries and CH ABS white similar to RAL9010 173g 248g Supply LonWorks bus Connector for antenna RXZ95 1 LON Gateway EnOcean LonWorks CM2N1661en_03 Technical data 2012 08 20 Dimensions Dimensions in mm 166 1M09 i 42 5 45 5 e e o z T 34 2500 19 20 Siemens RXZ95 1 LON Gateway EnOcean LonWorks CM2N1661en 03 Building Technologies Dimensions 2012 08 20 20 20 2008 2012 Siemens Switzerland Ltd Subject to change Siemens RXZ95 1 LON Gateway EnOcean LonWorks CM2N1661en_03 Building Technologies Dimensions 2012 08 20
7. HVACTemp C 25 30 nvoSetpoint 1 12 Ei 9 20 Siemens RXZ95 1 LON Gateway EnOcean LonWorks CM2N1661en_03 Building Technologies Workflow with RXT10 and LNS plug in 2012 08 20 Workflow with RXT10 and SBT generic plug in Infrastructure Basis Step Source Engineering with RXT10 and XIF Import 10 20 Siemens Building Technologies PC with DESIGO infrastructure RXT 10 version 4 or higher Download EasySens SRC Receiver zip Extract and save LON application 2_LON Software 1_deutsch EasySens Funk Empfangsmodule SRC04_SRC65 FT T srca_16_ 1 Ofisrca 16 1 01 XIF apb nxe xfb xif Download from the DESIGO RX intranet https intra industry siemens com bt global en business building comfort systems desigo ra Pages des ra units aspx TabcardNo 6 Set up the gateway with the RXT10 tool by following the standard procedure for integration of third party devices for details refer to User Manual RXT10 CM110669 Step 1 Procedure Device gt Add Select tab Device Type From selection menu Device Type select PLG Plug In Support On the Device list highlight PluglnDevice x Overview Application Device Type Settings Selected Application Device Type P G Plug In Support Device Description none PlualnDevice LN 5 Plug In Device LNS J POWERED Plug in Device for LNS Flug In Support Select tab Overview to enter the loca
8. SIEMENS enocealr DESIGO RXC Gateway EnOcean LonWorks For use with DESIGO RXC 1 661 1661P01 1661P02 RXZ95 1 LON Devices systems with LONWORKS communication Wireless receiver with LONWORKSO interface FTT10A Evaluation of up to 16 EnOcean room units Operating voltage AC DC 24 V CM2N1661en 03 2012 08 20 Building Technologies Use Type summary Ordering Equipment combinations EnOcean room units 2 20 Siemens Building Technologies Note With the RXC room controllers wireless room units can be used in place of the QAX3x standard room units One of the wireless technologies used is EnOcean Here the room unit is powered by a solar cell A battery is only needed if light conditions are poor The gateway requires a separate AC DC 24 V supply not in the scope of delivery Integration ot the EnOcean room units QAX9x x into the system is made via the RXZ95 1 LON EnOcean LONWORKS gateway It handles up to 16 EnOcean room units The telegrams received via radio are converted to LONWORKS standard network variables SNVT Product number Stock number Designation RXZ95 1 LON 955842 Z7100 Gateway EnOcean LONWORKS An external antenna is included in the delivery When ordering please give quantity designation product number and stock number When ordering please give Product number and Stock number Example 10 Gateways EnOcean LONWORKS RXZ95 1 LON 55842 Z100 Pro
9. al p Bee ets General settings General settings Display settings Sensors settings Lower set point change K Upper set point change K Fan speed Presence key min Receive time min Receiver settings Receiving LED Flashes Heartbeat Function Nv s s lO x 13 0 3 0 60 Po o H Flashing with each telegram received 2700 Receive time Sending interval Function not available with the RXT10 For monitoring the RF link to the room unit optional 2700 s 45 min 5b Configure the gateway select tab Switch settings y Thermokon Sensortechnik GmbH ENG STC FTT PlugInDevice 6 File Extra Help Recommendation Same as RXC gt Default O x eneral Genesal settings Display setting ensors a Q Button settings Long press time Dim Sending interval s Step value 9 5 Blind shu Teletiram up Telegram up Telegram STOP Telegram idle mode Reverse time ms Drive time s SET UP wl 100 E o SET DOWN QD ser sroP vj fo o SET NUL v 0 500 H 100 Functions not available with the RXT10O Siemens RXZ95 1 LON Gateway EnOcean LonWorks Building Technologies Workflow with RXT10 and LNS plug in 7 20 CM2N1661en 03 2012 08 20 Building Technologies Step Procedure 5c Configure t
10. as unsorted municipal waste The relevant national legal rules are to be adhered to Regarding disposal use the systems setup for collecting electronic waste Observe all local and applicable laws 17 20 RXZ95 1 LON Gateway EnOcean LonWorks CM2N1661en 03 Mounting 2012 08 20 Technical data General device data Housing protection Ambient conditions CE conformity Standards Enclosure Weight Connection terminals 18 20 Siemens Building Technologies Operating voltage Power consumption Interface Antenna connector Antenna included in delivery Terminals Cable entry Mounting Protection Temperature Humidity Electromagnetic Compatibility Radio and Telecommunications Terminal Equipment Directive DC 15 24 V AC 24 V 10 0 5W 0 82VA LONWORKS Transceiver FTT free topology FME female External antenna with magnetic stand Screw terminals max 1 5 mm M20 for 1 cable max D 8 mm or 2 cables max D 7 mm Wall mounting IP42 to EN60529 20 60 C max 70 r h non condensing 89 336 EEC R amp TTE 1999 5 EC Reduction of hazardous 2002 95 EC substances Electromagnetic compatibility Emission Immunity Telecommunications EN 61000 6 2 EN 61000 6 3 ETSI EN 301 4893 V 1 4 1 Home and building electronic systems EN 50090 2 2 HBES Registration for radio operation Material Color Without with packaging 1661209 o al TT E v sng g sng pug
11. duct number Stock number Designation QAX95 1 Wireless and battery less room unit with EnOcean interface temperature sensor QAX96 1 55623 H101 Wireless and battery less room unit with EnOcean interface temperature sensor with setpoint adjuster QAX95 4 Wireless and battery less room unit with EnOcean interface temperature sensor QAX96 4 55623 H105 Wireless and battery less room unit with EnOcean interface temperature sensor with setpoint adjuster QAX97 4 55623 H106 Wireless and battery less room unit with EnOcean interface temperature sensor with setpoint adjuster freely programmable button and 2 stage switch QAX98 4 55623 H108 Wireless and battery less room unit with EnOcean interface temperature sensor with setpoint adjuster freely programmable button and 5 stage switch The RXZ95 1 LON can be used in all systems with LONWORKS communication RXZ95 1 LON Gateway EnOcean LonWorks CM2N1661en_03 Use 2012 08 20 Topology LONWORKS O PXX L Jil PXC00 19 Ll 2 2 5 pe RXC O LIE Room unit 1 Temperature setpoint Integration of EnOcean room units into DESIGO RXC Mechanical design LED Power LED EnOcean communications Siemens RXZ95 1 LON Gateway EnOcean LonWorks Building Technologies Topology Desigo Insight Room unit 3 Total max Temperature setpoint 16 room units fan speed presence Screw terminals Service pin Service LED for commissioning Connect
12. ensor 6 amp Sensor 7 I amp Sensor 8 Learn in sensor a xi Sensor 9 v Would you like to take the Sensor ID 00 81 73 36 eT Button function Sensor 10 Sensor 11 Sensor 12 Sensor 13 11 Function check gateway room unit Thermokon Sensortechnik GmbH ENG STC FTT PlugInDevice amp File Extra Help g General Is Sensor settings Sensor 0 AB Sensors Sensor 0 General sensor settings Sensor 1 Device Universal Temperature sensor ORG 7 Sensor 2 Universal temperature range with SCPTminRnge and SCP Sensor 3 Sensor ID no 81 173 36 Learn in p s Sensor 4 Sending interval NY s s Sensor 5 Maximum output 9 5 100 Sensor 6 Lower temperature range C b Sensor 7 Upper temperature range C 40 Sensor 8 Temperature offset K Sensor 9 Network variable Type SNVT Sensor 10 o ES amp Sensor 11 nvoMultiOut 1 stwvr setting 7 m amp Sensor 12 nvoMultiOut 2 SNVT setting Sensor 13 Button function Sensor 14 Button 1 Notused gt Not used i Button 2 Notused gt Not used Button 3 Notused gt Not used Button 4 Notused gt Not used ll Visualisation M Monitor on Network access t Onnet connection to network Device state Online connection to device nviMultiOut 1 Fb o o 0 nviMultiOut 2 Fb o o 0 Write nvo
13. etpoint adjuster spega econtrol sunblind actuator spega econtrol sunblind actuator spega econtrol anti glare controller spega econtrol switch sensor spega ecantral thermo controller spega ecantral web command module spega ecantral web switche Th OF Cancel Select device template srca 16 1 01 gt OK Available Device Templates E x Device templates For plug ins cerca 16 1 O1 Programmid xSFFFADAB DSSUAUB 0 sten 55 1 1 Pragrammid OxSFFFAD 4600860420 sten 55 1 2 Pragrammld OxSFFFAD 4600660421 stca 55 1 1 Pragrammild Q43FFFAD 4600660424 thanas scc 1 Pragrammid O2SFFFAD 55008604077 sica hwl 15 1 z Programmld amp 3FFFADU ATOE 60409 OF Cancel Select function ThermokonLNSPlugln Device Configuration gt Click OK Select Plug in Function l x Available Functions Function Description tein Saeed Select a device Plug In Echelon LHS Report Generator LPALonvPlugn HAE Plugin amp ppLib V1 HAE Plugin AppLib v7 SBT Generic Plug In Thermokon SRHC FTT Hre reuister Plugin Close Confirm message by selecting YES 6 20 Siemens RXZ95 1 LON Gateway EnOcean LonWorks CM2N1661en 03 Building Technologies Workflow with RXT10 and LNS plug in 2012 08 20 Step Procedure 5a Configure the gateway Select tab General settings Thermokon Sensortechnik GmbH ENG STC_FTT PlugInDevice amp File Extra Help gt g Gener
14. he gateway select tab Sensor 1 16 y Thermokon Sensortechnik GmbH ENG STC FTT PlugInDevice_6 E Bl xl File Extra Help bs ee fs Sensor settings Sensor 0 a Sensors EL NM General sensor settings Sensor 1 Device Universal Temperature sensor ORG7 ve Sensor 2 Universal temperature range with SCPTminRnge and SCPTmaxRnge 7 Sensor 3 Sensor ID n0 00 00 00 Learn in Sensor 4 Sending interval Nv s s x w Sensor 5 Maximum output 94 oz Sensor 6 Lower temperature range C Sensor 7 Upper temperature range C joo zd Sensor 8 Temperature offset K x Sensor 9 Network variable Type SNVT Sensor 10 amp Sensor 11 nvoMultiout 1 ISNVT_setting amp Sensor 12 nvoMultiOut_2 ISNVT setting _ lt _ gt gt lt _ __ Sensor 13 Button function w Sensor 14 Button 1 Sensor 15 Button 2 Button 3 Button 4 Visualisation Monitor on Network access K Offnet no connection to network Device state Offline no connection to device nviMultiout 1 Fb 1 nviMultiut 2 Fb NEN nvoHvVACTemp C nS nvoSetpoint c nvoMultiOut 1 nvoMultiOut 2 Function not available with the RXT10 Device For room units QAX95 x QAX96 x select setting 7 SensorlD For offline engineering the EnOcean ID of the room unit can be entered here if desired Normally it is learned in online with
15. industry siemens com bt global en business building comfort systems desigo ra Pages des ra units aspx TabcardNo 6 Set up the gateway with the RXT10 tool by following the standard procedure for integration of third party devices for details refer to User Manual RXT10 CM110669 Step Procedure 1 Device gt Add Select tab Device Type From menu Device Type select PLG Plug In Support On the Device list highlight PluglnDevice x Overview Application Device Type Settings Selected Applic ation Device Type PLG Plug In Support Description none FPluglnDevice LAS Plug In Device LNs f POWERED Plug in Device for LNS Plug In Support 2 Select tab Overview and enter the location Confirm by clicking OK 5 20 RXZ95 1 LON Gateway EnOcean LonWorks CM2N1661en_03 Workflow with RXT10 and LNS plug in 2012 08 20 Step Procedure 3 RXT Select lt no networkinterface gt w Enocean workflow tbp DESIGO RXT10 2 Project Edit View Device Tools Network Window Help D co el eb Et SB is Bs XC S on Lom _xiet dt gt tena networkintetace gt jm LONT MIC 852 1 nn MIC 852 1 005 Network Connect Attached offnet 4 Device gt Configure gt ThermokonLNSPlugln Plug In gt OK Installed plug ins E E X Select a device plug in spega econtrol shading controller spega econtrol sistema MCT5 spega econtrol sistema MC spega econtrol temp sensor spega econtrol s
16. ine 11 Assign devices and install 12 Device gt Configure gt OK x Available Functions Function Description Browse Device Browse amp Configure the Device x Select a device Plug In Echelon LHS Report Generator LPALonvPlugn HAE Plugin amp ppLib V1 HAE Plugin AppLib v7 SBT Generic Plug In Hre reuister Plur Close 13 Learn in the room unit Select Node Object X Location Sica Description Default Device Nis CPs Device SRCA_16_1_01 Mae NodeO bject Sensar L Sensar 1 Sensor Sensor s Sensar 4 Sensor Senzor Sensor Sensors Sensar 3 Sensori Sensar 11 Sensar 12 Senzar 13 Sensar 14 Sensar 15 zi Automatic Update Update All Close DAQ NORMAL E rrva amp larmmSensar 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 E rvaFileDirectery 4002 E nvo5tatus 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 13 20 Siemens RXZ95 1 LON Gateway EnOcean LonWorks CM2N1661en 03 Building Technologies Workflow with RXT10 and SBT generic plug in 2012 08 20 Step Procedure Double click nviLearn gt Set Bit 0 1 to learn in Sensor 0 gt Press button on the room unit Location Sica Description Default Device NVs CPs Device SHLCA 16 1 l Made bject Sensar U Sensori Sensor Sensor s Sensor 4 Sensar 5 Senzor Sensor Sensor Sensar 3 Sensar 10 Sensar 11 Sensar 12 Sensor 3
17. or for antenna 1661206 01 3 20 CM2N1661en 03 2012 08 20 System requirements Software LNS Plugin Device resource files Thermokon_DRF24 exe LONWORKS application Software source documentation Thermokon LNS Plugln FT5000 Template srca 16 1 01 Functions Monitoring and configuration gateway room units For use with RXT10 tool or standard LNS tool The device resource files contain information about supplier specific configuration parameters and network variables UNVTs and UCTPs Prerequisite for installation is LONMARK resource files version 13 00 or alternatively LonMARK resource file API version 2 3 bothersome installation srca 16 1 O1 XIF NXE XFB XIF PDF if SRC FTT plug in is not used LNS plug in device resource files LONWORKS application Download from the DESIGO RX intranet https intranet10 sbt siemens com https intra industry siemens com bt global en business building comfort systems desigo ra Pages des ra units aspx TabcardNo 6 LONMARK resource files version 13 00 Download from http www lonmark org technical resources resource files Plug In Thermokon LNS Plug In 1 0 4198 23662 setup exe Environment for engineering tool Limitations 4 20 Siemens Building Technologies Integration of QAX95 x QAX96 x The RXT10 tool or a standard LNS tool can be used Integration of QAX97 x QAX98 x A standard LNS tool must be used With a DESIGO system it is not possible
18. rt Generator LPALanvPlugin HALE Plugin amp ppLib V1 HAC Plugin amp ppLib v z SBT Generic Plug In He register Plug in Close RXZ95 1 LON Gateway EnOcean LonWorks CM2N1661 Workflow with RXT10 and SBT generic plug in 11 20 en 03 2012 08 20 12 20 Siemens Building Technologies Step Procedure 6 Configure the gateway Select Node id al Location Sica Description Default Device Nis CPs LNS SRLA 15 1 Ul NodeObyect SCPT bypassT ime Node bject Sensar U SLPT drive Time Moda bject Sensori El l aa CP iter me NodeDbiect minS endTime ode jec j eal SCPT stepv alue NodeO bject 5 0 sensor 4 UCPT enoceanRicyT m Moda bject bl sensar 5 LICPTFanSpdStages Made bject 3 Sensar E5 LICPT generalCP1 NodeO bject 1 0 0 0 0 0 0 0 Sensor UCPTlongPressT ime Model bject 1 0 20 2020 Sensar 8 UCPTreverseDelay NodeQ bject Sn Sensor 8 LICPT spl ax alue NodeO bject 3 00 Sensor10 UICPT spMiriv alue NodeUbject 3 00 11 UCPT sunblindD Ow Mode byect SET DOWN 1 ensar T1 LICPT sunblindl DLE NodeQbject SET MULT sensar 12 LICPTsunblind5 T OP Node bject SET_STOP n sensor 3 UCPT sunblindLIP NodeO bject SET_UP 100 0 Senzori 4 Sensorl 5 Bi Automatic Update Update All Close SCPTmaxSendTime sending interval LONWORKS Recommendation Same as RXC gt Default 2700 s 45 min UCPTenoceanRcvTm Receive time For monitoring the RF link to
19. the room unit optional UCPTspMax MinValue Setpoint Offset 3 K default 7 Configure the gateway Select Sensor Sect 0 15 Location Sica Description Default Device Nye CPs LN5 SHLA 15 1 Ul MadelIbiect nvoHVACTemp 1 5CPTmasRin Sensor U 40 00 Sensar U mvaHVACTemp 1 5CPTminRnge Sensor U 0 00 Sensorli nmvaHVACTemp 1 5CPTtempUE Sensor 0 0 00 Sensor 2 nvaM ulti utL_1_1 S5CPTrvType Sensor PID 0 0 0 0 0 0 Sensor 3 nvoldulidut 2 1 5CPTmvTupe Sensor Q PID C CEDECEDED Senscil4 ELEM marO ut sensori i 00 0 ESCPT maxSendT ime Sensor l TO sensors UCPT devicel ype Sensaor U sensor 6 UCPTdiContig Sensor 0 0 0 0 0 Sensors LULPTenaceanlD Sensor U 0 0 0 0 Sensor Sensar 3 Sensor 1 0 Sensor 1 Sensor 2 Sensar 13 Sensor 4 Sensar 15 gt Automatic Update Update All Close SCPTmax minRnge Measuring range of temperature sensor 0 40 C default SCPTmaxSendTime sending interval LONWORKS Recommendation Same as RXC gt Default 2700 s 45min RXZ95 1 LON Gateway EnOcean LonWorks CM2N1661en 03 Workflow with RXT10 and SBT generic plug in 2012 08 20 Step Procedure 8 gt Close gt Active Plug in finish Network gt Disconnect Attached offnet 9 Make RXT10 bindings Datapoint Gateway RXC Room Temperature nvoHVACTemp x gt nviSpaceTemp Setpoint Offnet nvoSetpoint x gt nviSetpointOffset 10 Netwok gt Connect onl
20. tion Confirm by clicking OK RXT Select lt no networkinterface gt g Enocean workflow tbp DESIGO RXT10 2 Project Edit View Device Tools Network Window Help Dee amp b A E uH X 57 e oa LON1 NIC S52 1 005 Network Connect Attached offnet RXZ95 1 LON Gateway EnOcean LonWorks CM2N1661en 03 Workflow with RXT10 and SBT generic plug in 2012 08 20 Siemens Building Technologies Step 4 Procedure Device gt Configure gt SBT Generic Plug In gt OK Installed plug ins E x Select a device plug in Echelon LAS Report Generator LPACanvPlugin HL Plugln amp ppLib 1 HL Plugin amp ppLib V2 SBT Genenec Plug In h Select function Import XIF gt OK Select Plug in Function l x Available Funcions Function Description riportestt I Get the Lon interface out of device or read it Conficure Devize trom a tle Browse Device nk hs Select a device Plug In Echclon LHS Report Generator LPALonvPlugin RSC Plugin amp ppLib V1 R amp C Plugin ppLib V2 SBT Generic Plug In He regisler Plug in Clase gt Read XIF File gt Select path for srca 16 1 01 XIF gt OK gt Select Plug in gt Close Device gt Configure gt OK depending on plug in Configure Device x Available Functions Function Description L anfigure Device Browse Device Browse amp Configure the Device x Select a device Plug In Echelon LNS Repo
21. to integrate additional EnOcean products such as buttons presence detectors etc via the RXZ95 1 LON gateway with the RXT10 tool Reason In the gateway temperature and setpoint adjustment are available as static network variables However additional functions are configured dynamically and the RXT10 does not support dynamic network interfaces e RXT10 does not support the multifunctional button of the QAX97 4 und QAX98 4 room units For technological reasons the control performance of an RXC room controller in connection with an EnOcean room unit is inferior to that with a standard QAX3x room unit RXZ95 1 LON Gateway EnOcean LonWorks CM2N1661en 03 System requirements 2012 08 20 Workflow with RXT10 and LNS plug in Infrastructure Basis Note Step 1 Source Step 2 Source Step 3 Source Engineering with RXT10 and LNS plug in Siemens Building Technologies PC with DESIGO infrastructure RXT10 version 4 or higher The following components must be installed in the order indicated Installation of LONMARK resource files version 13 00 or higher http www lonmark org technical_resources resource_files Installation of device resource files Download from the DESIGO RX intranet https intra industry siemens com bt global en business building comfort systems desigo ra Pages des ra units aspx TabcardNo 6 Installation of Thermokon plug in Download from the DESIGO RX intranet https intra
Download Pdf Manuals
Related Search