V. 03 - Velleman
Contents
1. Wluxibe NUXILED 3000 DMX CONTROLLED LED STROBE LX306 USER MANUAL C LX306 User Manual 1 Introduction To all residents of the European Union Important environmental information about this product This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm the environment Do not dispose of the unit or batteries as unsorted municipal waste it should be taken to a specialized company for recycling This device should be returned to your distributor or to a local recycling service Respect the local environmental rules EE r in doubt contact your local waste disposal authorities Thank you for choosing Luxibel Please read the manual thoroughly before bringing this device into service If the device was damaged in transit don t install or use it and contact your dealer 2 Safety Instructions This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children shall be supervised to ensure that they do not play with the appliance Never let the device run unattended Do not crimp the power cord and protect it against damage Warning If the power cord is damaged it must be replaced by the manufacturer its service ag2. 005 Blackout 006 249 Flash rate slow to fast 250 255 Full on 7 Auto Programs 000 010 No Function 011 040 Auto 0 041 070 Auto 1 071 100 Auto 2 101 130 Auto 3 131 160 Auto 4 161 190 Auto 5 191 220 Auto 6 221 255 Auto 7 8 Auto speed 000 255 Auto speed slow to fast 9 Dimmer 000 255 0 100 10 Strobe 000 005 No Function 006 255 Strobe Slow to Fast V 03 30 07 2014 8 Velleman nv LX306 8 Cleaning and Maintenance Before starting any cleaning or maintenance activities 1 Unplug the device s power cord from the outlet 2 Let the device cool down Cleaning e Clean the external optics with a soft cloth e Always be sure to dry all parts completely before plugging the unit back in e Cleaning frequency depends on the environment in which the unit operates i e smoke fog residue dust dew e Do not immerse the device in any liquid Maintenance e All screws should be tightened and free of corrosion e The housing the lenses the mounting supports and the installation location e g ceiling Suspension trussing should not be deformed modified or tampered with e g do not drill extra holes in mounting supports do not change the location of the connections e Mechanically moving parts must not show any signs of wear and tear e The electric power supply cables must not show any damage Have a qualified technician maintain the device e There are no user serviceable parts apart from the fuse e Refer to an authori
3. electronics world and currently distributes its products in over 85 countries All our products fulfil strict quality requirements and legal stipulations in the EU In order to ensure the quality our products regularly go through an extra quality check both by an internal quality department and by specialized external organisations If all precautionary measures notwithstanding problems should occur please make appeal to our warranty see guarantee conditions General Warranty Conditions Concerning Consumer Products for EU e All consumer products are subject to a 24 month warranty on production flaws and defective material as from the original date of purchase e Velleman can decide to replace an article with an equivalent article or to refund the retail value totally or partially when the complaint is valid and a free repair or replacement of the article is impossible or if the expenses are out of proportion e You will be delivered a replacing article or a refund at the value of 100 of the purchase price in case of a flaw occurred in the first year after the date of purchase and delivery or a replacing article at 50 of the purchase price or a refund at the value of 50 of the retail value in case of a flaw occurred in the second year after the date of purchase and delivery e Not covered by warranty o all direct or indirect damage caused after delivery to the article e g by oxidation shocks falls dust dirt humidity
4. shipping costs e The above conditions are without prejudice to all commercial warranties The above enumeration is subject to modification according to the article see article s manual Velleman nv Legen Heirweg 33 9890 Gavere Belgium www velleman eu V 03 30 07 2014 10 Velleman nv
5. 005 No effect macros 006 042 Macro 1 slow to fast 043 085 Macro 2 slow to fast 086 128 Macro 3 slow to fast 129 171 Macro 4 slow to fast 172 214 Macro 5 slow to fast 215 255 Macro 6 slow to fast Channels 1 2 3 and 4 are available in 5 channel mode 6 channel mode channel Function Value Percent Setting 1 Flash 1 000 005 Blackout 006 249 Flash rate slow to fast 250 255 Continuous blinder effect 2 Flash 2 000 005 Blackout 006 249 Flash rate slow to fast 250 255 Continuous blinder effect 3 Flash 3 000 005 Blackout 006 249 Flash rate slow to fast 250 255 Continuous blinder effect V 03 30 07 2014 7 Velleman nv LX306 4 Flash 4 000 005 Blackout 006 249 Flash rate slow to fast 250 255 Continuous blinder effect 5 Flash 5 000 005 Blackout 006 249 Flash rate slow to fast 250 255 Continuous blinder effect 6 Flash 6 000 005 Blackout 006 249 Flash rate slow to fast 250 255 Continuous blinder effect The LEDs can be controlled in 6 segments 1 2 3 4 5 6 4 T 10 channel mode channel Function Value Percent Setting 1 Flash 1 000 005 Blackout 006 249 Flash rate slow to fast 250 255 Full on 2 Flash 2 000 005 Blackout 006 249 Flash rate slow to fast 250 255 Full on 3 Flash 3 000 005 Blackout 006 249 Flash rate slow to fast 250 255 Full on 4 Flash 4 000 005 Blackout 006 249 Flash rate slow to fast 250 255 Full on 5 Flash 5 000 005 Blackout 006 249 Flash rate slow to fast 250 255 Full on 6 Flash 6 000
6. ance of 0 5 m between the device s light output and any illuminated surface e The maximum ambient temperature is 40 C Do not operate the device at higher temperatures V 03 30 07 2014 2 Velleman nv 3 LX306 General Guidelines Refer to the Velleman Service and Quality Warranty on the last pages of this manual Keep this device away from dust and extreme temperatures Make sure the ventilation openings are clear at all times For sufficient air circulation leave at least 1 2 5 cm in front of the openings y Protect this device from shocks and abuse Avoid brute force when operating the device v Familiarise yourself with the functions of the device before actually using it Do not allow operation by unqualified people Any damage that may occur will most probably be due to unprofessional use of the device All modifications of the device are forbidden for safety reasons Damage caused by user modifications to the device is not covered by the warranty Only use the device for its intended purpose All other uses may lead to short circuits burns electroshocks lamp explosion crash etc Using the device in an unauthorised way will void the warranty Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer will not accept responsibility for any ensuing defects or problems Mechanical wear and LEDs are not covered by warranty A qualified technician s
7. and by the article as well as its contents e g data loss compensation for loss of profits o consumable goods parts or accessories that are subject to an aging process during normal use such as batteries rechargeable non rechargeable built in or replaceable lamps rubber parts drive belts unlimited list o flaws resulting from fire water damage lightning accident natural disaster etc o flaws caused deliberately negligently or resulting from improper handling negligent maintenance abusive use or use contrary to the manufacturer s instructions o damage caused by a commercial professional or collective use of the article the warranty validity will be reduced to six 6 months when the article is used professionally o damage resulting from an inappropriate packing and shipping of the article o all damage caused by modification repair or alteration performed by a third party without written permission by Velleman e Articles to be repaired must be delivered to your Velleman dealer solidly packed preferably in the original packaging and be completed with the original receipt of purchase and a clear flaw description e Hint In order to save on cost and time please reread the manual and check if the flaw is caused by obvious causes prior to presenting the article for repair Note that returning a non defective article can also involve handling costs e Repairs occurring after warranty expiration are subject to
8. d software version Address 001 512 Sets product s DMX address Channel 1 Ch 1 channel strobe 5 Ch 5 channel intensity duration rate effect macro 6 Ch 6 channel Flash 1 6 10 Ch 10 channel Flash 1 6 auto programs auto speed dimmer strobe M amp S Mode Master Selects Master mode Slave Selects Slave mode Temp xx C Displays product s internal temperature V 03 30 07 2014 5 Velleman nv LX306 Power Linking The LX 306 supports power linking You can power up to 6 devices at 230 V Never exceed this number Power linking cords can be purchased separately DMX Linking You can link the device to any DMX controller with a standard DMX serial connection If you use another DMX compatible product with the LX306 you can control each device with a single DMX controller 7 2 Stand Alone Mode In stand alone mode the device runs one of the built in programs To set the device to stand alone mode 1 Unplug any connection from the DMX input of the device 2 Press MENU until lt Auto gt is displayed and press ENTER 3 Use UP and DOWN to select the built in program and press ENTER 7 3 Master Slave Mode The master slave mode allows for connecting several devices to a single master device in a daisy chain All slave devices will then work synchronously with the master device The first device in the daisy chain functions as the master device To set the devices to master slave mode 1 Unplug any connection from the DMX in
9. ent or similarly qualified persons in order to avoid any hazard Make sure that the available voltage does not exceed the voltage stated in the specifications of this manual This device falls under protection class I It is therefore essential that the device be earthed Have a qualified person carry out the electric connection Be very careful during the installation touching live wires can cause life threatening electroshocks Do not use the device when damage to housing or cables is noticed Do not attempt to service the device yourself but contact an authorised dealer or service agent Always disconnect mains power when device not in use or when servicing or maintenance activities are performed Handle the power cord by the plug only Caution device heats up during use Do not touch hot surfaces Let the device cool down sufficiently after switching off before handling Indoor use only Keep this device away from rain moisture splashing and dripping liquids Never put objects filled with liquids on top of or close to the device Do not stare directly at the light source as this may cause e epileptic seizure in sensitive people e temporarily loss of sight flash blindness e permanent irreversible eye damage e Use an appropriate safety cable to fix the device e g VDLSC7N or VDLSC8N e Install the device at a minimal distance of 0 5 m from flammable and explosive objects or substances e Respect a minimum dist
10. f devices on a serial data link is 32 devices e A DMX terminator is recommended for installations where the DMX cable has to run a long distance or is in an electrically noisy environment e g discos The terminator prevents corruption of the digital control signal by electrical noise The DMX terminator is simply an XLR plug with a 120 Q resistor between pins 2 and 3 which is then plugged into the XLR output socket of the last device in the chain 7 Operation The device can be used in the following modes e stand alone mode e master slave e with a DMX512 controller 7 1 Control Panel Navigation Access the control panel functions using the four panel buttons located directly underneath the display From left to right Button Function MENU to access the menu quit the current function without saving the setting or quit the menu UP to scroll upward in a list of functions or options or increase a value DOWN to scroll downward in a list of functions or options or decrease a value ENTER to confirm and save a selected option or value Menu name Options Description Auto Auto 0 7 Speed 001 100 8 automatic programs and speed adjustment Static Dimmer 000 255 Sets the intensity of the light output Strobe Selects the strobe frequency BackLite On 10S Sets the amount of time the control panel 20S backlight stays on 30S Info Auto Test Sets product in test mode FixHours Fixture running time 0 9999H Default OH Version Vx x Shows the installe
11. hall install and service this device Do not switch the device on immediately after it has been exposed to changes in temperature Protect the device against damage by leaving it switched off until it has reached room temperature This device is designed for professional use on stage in discos theatres etc Lighting effects are not designed for permanent operation regular operation breaks will prolong their lives There may be some smoke or a particular smell when the device is activated for the first time This is normal and any smoke or smell will gradually disappear Use the appropriate current and power supply see Technical Specifications Keep this manual for future reference Features die cast light housing special for rental companies DMX controlled via 1 5 6 or 10 channels for simple or advanced controlling 1 channel mode strobe 5 channel mode dimmer strobe strobe rate macros segment control 6 channel mode strobe for each segment 6 10 channel mode strobe for each segment 6 auto program auto program speed master dimmer shutter pre programmed stand alone effects built in programs with speed adjustment and master slave mode flicker free 400 Hz clear LCD display for easy menu setting o O O O V 03 30 07 2014 3 Velleman nv LX306 5 Overview S a m display amp iii jma safety ring ji gt J j j J 3 pin 5 pin XLR XLR powercon fu
12. ith a DMX controller 1 Press MENU until lt Channel gt is displayed and press ENTER 2 Use UP and DOWN to select a channel and press ENTER 3 Press MENU until lt Address gt is displayed and press ENTER 4 Use lt UP gt and lt DOWNS gt to set the DMX start address and press ENTER Start addresses Use the table below to define the correct address The table shows the settings for units 1 to 3 Apply the same principle for the other units Channel mode First unit Second unit Third unit Highest start address 1 Start address 1 2 1 1 3 2 1 512 Channel Lei 2 2 3 3 V 03 30 07 2014 6 Velleman nv LX306 Channel mode First unit Second unit Third unit eee as 5 Start address 1 6 1 5 11 6 5 508 Channel 1 5 6 10 11 15 6 Start address 1 7 1 6 13 7 6 507 Channel 1 6 7 12 13 18 10 Start address 1 11 1 10 21 11 10 503 Channel 1 10 11 20 21 30 7 5 DMX Channel Values 1 channel mode channel Function Value Percent Setting 1 Flash 000 005 Blackout 006 249 Flash rate slow to fast 250 255 Continuous blinder effect 5 channel mode channel Function Value Percent Setting 1 Flash intensity 000 005 Black out 006 255 Minimum to maximum 2 Flash duration 000 255 Flash duration 15 990 ms 3 Flash rate 000 005 No flash 006 255 1Hz 30 Hz 4 Special effects 000 005 No effect 006 042 Ramp up 043 085 Ramp down 086 128 Ramp up down 129 171 Random 172 214 Lightning 215 255 Spikes 5 Pixel control 000
13. oad limits determining the installation material to be used Have the material and the device itself checked regularly Do not attempt to install the device yourself if you lack these qualifications as improper installation may result in injuries e Make sure there is no flammable material within a 0 5 m radius of the device e Have a qualified electrician carry out the electric connection e Connect the device to the mains with the power plug All devices must be powered directly off a grounded switched circuit and cannot be run off a rheostat or dimmer circuit even if the rheostat or dimmer channel is used solely for 0 to 100 switching e The device has a power output to supply power to another device When connecting several devices in a daisy chain via this output make sure that the total current does not exceed the power line s V 03 30 07 2014 4 Velleman nv LX306 nominal current Use power cables with an adequate section The installation has to be approved by an expert before the device is taken into service DMX 512 Connection e When applicable connect an XLR cable to the female XLR output of a controller not incl and the other side to the male XLR input of the device Multiple devices can be linked through serial linking The linking cable shall be a dual core screened cable with XLR input and output connectors e Maximum recommended serial data link distance is 500 meters 1640 ft Maximum recommended number o
14. put of the master device the first device in the chain 2 Connect the DMX input of the first slave device to the DMX output of the master device 3 Connect the DMX input of the subsequent slave devices to the DMX output of the previous slave device Master 1 Set up the unit as described in the section Stand Alone Mode above 2 Press MENU until lt M amp S Mode gt is displayed and press ENTER 3 Use UP and DOWN to select lt Master gt and press ENTER Slave 1 On each slave device press MENU until lt M amp S Mode gt is displayed and press ENTER 2 Use UP and DOWN to select lt Slave gt and press ENTER 7 4 DMX Mode The DMX mode allows you to control the device with any universal DMX controller e All DMX controlled devices need a digital start address so that the correct device responds to the signals This digital start address is the channel number from which the device starts to listen to the DMX controller The same starting address can be used for a whole group of devices or an individual address can be set for every device e When all devices have the same address all the units will listen to the control signal on one particular channel In other words changing the settings of one channel will affect all devices simultaneously If you set individual addresses each device will listen to a separate channel number Changing the settings of one channel will only affect the device in question To set the device to work w
15. se in out in out in out 6 Installation Choose a suitable mounting spot Mount the device in the desired angle using the included bracket Connect the power cord to the mains Disconnect after use Mounting the Device e Have the device installed by a qualified person respecting EN 60598 2 17 and all other applicable norms e The carrying construction must be able to support 10 times the weight of the device for 1 hour without deforming e For truss mounting use an appropriate clamp not incl and fit an M10 bolt through the centre of the folded bracket e The installation must always be secured with a secondary attachment such as a safety cable e g VDLSC7N or VDLSC8N The secondary attachment shall be designed and mounted in such a way that no part of the device can fall if the primary attachment fails e Make sure that the safety cables can carry 10 times the weight of the device Make sure that the maximum height of drop is limited so that no injuries can occur If the safety cables are long wrap them around the truss multiple times to reduce the height of drop to a safe level e Never stand directly below the device when it is being mounted removed or serviced Have a qualified technician check the device once a year and once before you bring it into service e Install the device in a location with few passers by that is inaccessible to unauthorised persons e Overhead mounting requires extensive experience calculating workl
16. zed dealer for service and or spare parts Replacing the fuse Only replace the fuse by a fuse of the same type and rating 1 Unplug the device s power cord from the outlet 2 Use a flat head screwdriver to remove the fuse holder 3 Remove the damaged fuse and replace with the same type of fuse 4 Insert the fuse holder back in its place and reconnect power 9 Technical Specifications power supply 100 240 VAC 50 60 Hz powerCON in and out power consumption 460 W LED source 882 x 0 5 W SMD 6500 K colour temperature 6500 K beam angle 120 DMX in and output 3 and 5 pin XLR dimensions 455 x 221 x 103 mm weight 4 5 kg Fuse T5A 250 V Use this device with original accessories only Velleman nv cannot be held responsible in the event of damage or injury resulting from incorrect use of this device For more info concerning this product and the latest version of this manual please visit our website www luxibel com The information in this manual is subject to change without prior notice COPYRIGHT NOTICE The copyright to this manual is owned by Velleman nv All worldwide rights reserved No part of this manual may be copied reproduced translated or reduced to any electronic medium or otherwise without the prior written consent of the copyright holder V 03 30 07 2014 9 Velleman nv LX306 Velleman Service and Quality Warranty Since its foundation in 1972 Velleman acquired extensive experience in the
Download Pdf Manuals
Related Search