Scala Rider Q2 Manual
Contents
1. Gebrauchsanleitung Guide d Utilisation Guida di Avvio Guia de Usario CARDO User Guide SCALA RIDER QGQ2_A5_021 indd 1 2 19 08 1 51 36 PM C AR DO scala rider 02 Congratulations and thank you for having chosen the scala rider Q2 Bluetooth Headset for bikers This Manual will help you operate the headset but you should first familiarize yourself with the Bluetooth functionality of your cellular phone and or GPS device before using the scala rider Q2 The retail box of the scala rider Q2 contains one headset unit When paired with another scala rider Q2 the headsets can be used as an Intercom at a range of up to 1 640 ft 500m The scala rider Q2 offers the following uses 1 Bluetooth headset for mobile phone communication supporting headset and Handsfree profiles 10m range 2 Bike to Bike Intercom Communication with another Q2 unit up to 1 640 ft 500 m range in Full Duplex mode purchased separately 3 Turn by Turn GPS Navigation instructions and Streaming Audio from compatible Bluetooth devices 4 FM Radio built in FM radio receiver with six preset stations The scala rider Q2 can establish an audio connection with one Bluetooth device at a time Please read the section Using the Headset to see how you can switch the audio connection between the paired devices Mobile phones that do not support the Bluetooth Handsfree profile may prevent you from using the Red2. there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct For additional information please visit our website at the interference by one or more of the following measures www cardosystems com FAQ www cardosystems com faq or contact us at support cardosystems com Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Phone USA and Canada 1 800 488 0363 Consult the dealer or an experienced radio TV technician for help International 4989 450 36819 Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Federal Communications Commission FCC Statement 15 21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user s authority to operate the equipment FCC RF Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment End users must follow the
3. tion Cardo will not be responsible for any physical damages irrespective of reasons conditions or circumstances including malfunctioning of the Device and all risks associated with operating it rest solely and entirely with the user of this Device irrespective of whether the Device is used by the original purchaser or any third party Cardo hereby notifies you that using this Device may also be in contraven tion to local federal state or national laws or regulations and that any use of the Device is entirely at your sole risk and responsibility 1 You your heirs legal representatives successors or assigns hereby voluntarily and forever release discharge indemnify and hold harmless Cardo from any and all litigation claims debts demands actions and li ability which may arise directly or indirectly from using the Device for any distress pain suffering discomfort loss injury death damages to or in respect to any person or property however caused WHETHER ARISING FROM THE NEGLIGENCE OR OTHERWISE and which may hereafter accrue to you on some future date as a result of said use to the fullest extent permitted by law 2 You fully understand and assume the risks in using the Device including risk of negligent acts or omissions by others 3 You confirm that you are physically capable to use the Device and that you have no medical conditions or needs that may infringe upon your abili ties to do so in a safe manner You
4. 3 seconds Call being initiated or in progress FM Radio ON There are six pre set Radio stations available on your scala rider Q2 While the Radio is on tap the MC Button to cycle between saved 1 red flash every 3 seconds Battery is low 00 2 red flashes every 3 seconds Call being initiated or in progress FM Radio ON and battery is low While the Radio is on press and hold the Volume Up or Volume Down Button for three seconds or until you hear the next station on your headset Searching for a New FM Radio Station Solid red Headset is being charged Pressing Volume Up will search upwards higher frequency Pressing Volume Down will search downwards lower frequency Once a station is found searching stops and you can hear the station Your headset is equipped with a high quality FM Radio receiver This section explains how to enjoy the functions of the FM Radio To save this station refer to the following section The scala rider Q2 enables you to listen to FM Radio while you are To continue searching press the Volume Up or Volume Down Button not receiving audio from another audio source again for three seconds While listening to the radio you do not have to worry about missing You may still continue to listen to the current unsaved station any calls as the headset automatically mutes the FM Radio and Pressing the MC Button in this case will switch to the next saved switches to Bluetooth headset operation when an incoming
5. Red Light begins flashing rapidly indicating it is in Intercom Pairing mode 4 Repeat Step 3 again for the second scala rider Q2 headset Both headsets should now be flashing rapidly in Red VI Within a few seconds both headsets will show a solid Red light for two seconds and then begin flashing slowly in Blue SECONDARY BUDDY PAIRING requires three scala rider Q2 headsets Once you have paired the Main scala rider Q2 to the Primary Buddy headset repeat the procedure above to pair the Main scala rider Q2 to the Secondary Buddy headset NOTE The Main scala rider Q2 is able to communicate with either the Primary Buddy or the Secondary Buddy The Primary Buddy and Secondary Buddy are not able to communicate directly via Intercom NOTE If the Pairing process is not completed within one minute the headset will return to Standby mode STEP 2 Optional SET UP FOR RIDER TO PASSENGER INTERCOM PAIRING There are two ways that the scala rider Q2 can be used for Rider to Passenger communication A Both Rider and Passenger are using scala rider Q2 headsets To Pair the two headsets follow the Steps listed in the section above titled PRIMARY BUDDY PAIRING B The Rider is using a scala rider Q2 and the Passenger is using a scala rider headset i e a scala rider a scala rider FM or a scala rider TeamSet Driver unit headset To Pair the two headsets 1 Starting with the scala rider headset turned OFF press an
6. THE ABOVE AND RENOUNCE ALL RIGHTS TO FUTURE CLAIMS AND DE MANDS AGAINST CARDO AS DEFINED ABOVE www cardosystems com m QGQ2_A5_021 indd 12 2 19 08 1 52 10 PM
7. call is station received or when you decide to initiate a call When the conversation is over the headset automatically tunes back in to the FM Radio Turning the FM Radio On While no call is on the headset either mobile phone call or Intercom call press and hold the MC Button on your headset for three seconds SS 6 m QGQ2_A5_021 indd 9 2 19 08 1 52 06 PM Saving an FM Radio Station The FM Radio is equipped with a memory capacity of six stations e Select the station you wish to replace by tapping the MC button until you find the station you want to replace CARDO scala rider 02 NOTICES e Search for a new station as described above 15 105 b e Tap the MC Button within 20 seconds of finding the station to This equipment has been tested and found to comply with the limits save the current station for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against If you don t save the station the Radio will exit search mode without harmful interference in a residential installation This equipment saving the current station You can still continue to listen to the generates uses and can radiate radio frequency energy and if current unsaved station Tapping the MC Button in this case will not installed and used in accordance with the instructions may move to the next saved station cause harmful interference to radio communications However
8. confirm that you are at least eighteen 18 years of age and that you have been advised of the risks associated with the use of the Device You further confirm that you will not consume any alcohol that may affect your alertness or any mind altering substance and will not carry use or consume these substances before or during the use of the Device mr __ QGQ2_A5_021 indd 11 2 19 08 1 52 09 PM C AR DO scala rider 02 NOTICES 4 You fully acknowledge our warnings and understand that a risks and dangers exist in using the Device while in traffic including but not limited to injury or illness strains fractures partial and or total paralysis death or other ailments that could cause serious disability c these risks and dan gers may be caused by the negligence of the manufacturers or its agents or any third party involved in designing or manufacturing the Device d these risks and dangers may arise from foreseeable or unforeseeable causes You hereby assume all risks and dangers and all responsibility for any loss es and or damages whether caused in whole or in part by the negligence or other conduct of others including the Company 5 You confirm that you have read this release of liability and fully under stand its terms and that you have given up substantial rights by not return ing the Device for a full refund see refund
9. Buttons 2 While charging the Red Light turns on it may take up to 15 seconds until the Red Light turns on When charging is complete the Red Light will turn off scala rider02 CA2RDO Rider to me Passenger Embedded Sg Full Duplex FM Radio Intercom l Connection Bike to Bike Intercom w 500 meters ai 1 640 ft scala riderQ2or AI ee scala rider hd Family Headset Se Mobile Phone SET UP FOR BIKE TO BIKE INTERCOM PAIRING The scala rider Q2 can be paired with up to two other headsets for Intercom communication referred to in this guide as Primary Buddy and Secondary Buddy Pairing is a one time process Once the headsets are paired during this Setup Procedure they will remain paired and automatically recognize each other whenever they are within range NOTE The scala rider Q2 allows you to speak via Intercom to one Buddy headset at a time SSS QGQ2_A5_021 indd 3 2 19 08 1 51 54 PM CA2DO scala rider 02 SETUP AND CONFIGURATION PRIMARY BUDDY PAIRING requires two scala rider Q2 headsets If either headset is turned OFF turn it ON by pressing and holding the CTRL Button until the Blue Light flashes three times N Make sure that both headsets are now flashing slowly in Blue Uo Pick up one headset and simultaneously press and hold the CTRL Button and MC Button for at least six seconds until the
10. begin immediately TROUBLESHOOTING THE INTERCOM First make sure your microphone is located properly in front of the center of your mouth The scala rider Q2 is designed for use in loud environments Please make sure to test the Intercom functionality in a LOUD environment such as next to an idling motorcycle Please also verify that the headsets were paired together properly by following the instructions in the relevant Setup sections Setting Voice Connect Intercom preference Primary vs Secondary Buddy The headset s Voice Connect feature allows you to start a Buddy Intercom call by simply speaking into the microphone You can define which of the two Buddy headsets you wish to connect to when using Voice Connect Intercom NOTE The Primary Buddy has priority by default To toggle the Voice Connect Intercom between Primary and Secondary Buddy Press and hold the Volume Up Button for three seconds and you will hear a beep SETUP AND CONFIGURATION e One beep Voice Connect set to Primary Buddy e Two beeps Voice Connect set to Secondary Buddy Enable Disable Voice Connect feature Press and hold the Volume Up and Down Buttons simultaneously until you hear a beep The default status is Voice Connect enabled NOTE The Enable Disable Voice Connect feature affects both the Intercom and the mobile phone functionality PHONE FUNCTIONS Short press the CTRL Button or speak loudly any word of your choice Answ
11. d hold the CTRL button until the Red Blue lights begin rapidly alternating 2 Starting with the scala rider Q2 turned ON simultaneously press and hold the CTRL Button and MC Button for six seconds until the Red light begins flashing rapidly indicating it is in Intercom Pairing mode 3 Within a few seconds the scala rider Q2 will show a solid Red light for two seconds and then begin flashing slowly in Blue NOTE If the Pairing process is not completed within one minute the headset will return to Standby mode NOTE When using a scala rider headset as a Passenger headset Voice Connect Intercom can be initiated only by the scala rider Q2 headset Manual Connect Intercom can be initiated from either headset RESET INTERCOM PAIRING You can delete all of the headset s Intercom pairings at any time ee QGQ2_A5_021 indd 4 2 19 08 1 51 56 PM SETUP AND CONFIGURATION scala rider 02 KS NARDO 1 Place the scala rider Q2 into Intercom Pairing mode following the instructions in the PRIMARY BUDDY PAIRING section above 2 Once the Red Light begins flashing rapidly press and hold Volume up for three seconds 3 The Red and Blue Lights will flash five times confirming that the Reset Pairing was successful SET UP FOR MOBILE PHONE CALLS PAIRING If you have a Bluetooth enabled mobile phone and would like to make and receive phone calls using the scala rider Q2 you must first pair your headset to the mobile ph
12. er a call Short press the MC Button or remain silent for 15 seconds Short press the CTRL Button During Standby short press the CTRL Button and state the name of the person you wish to call This feature is supported only by mobile phones that support the Voice Dial feature Redial Press and hold the Volume Down Button for three seconds Reject a call Terminate a call Voice Dial NOTE If your Bluetooth mobile phone is paired to a Bluetooth GPS device not directly to the scala rider Q2 some of the above Phone functions may not be compatible When the headset is on an active phone call any Buddy Intercom call request will be rejected automatically Once the phone call audio link drops you can initiate and accept Buddy Intercom calls e QGQ2_A5_021 indd 8 2 19 08 1 52 06 PM SETUP AND CONFIGURATION SUPPORT NOTICES scala rider 02 KS NARDO to turn on the radio The radio tunes in to the last radio station you were listening to With some phones you should wait a few seconds after ending a call before turning on the Radio Turning the FM Radio Off While the radio is turned on press and hold the MC button for three seconds to turn the Radio off None Headset is off Alternating Red blue flashes Mobile phone GPS Pairing mode Rapid Red flashes Intercom Pairing mode 1 blue flash every 3 seconds Standby No call is in progress SIN n Switching Preset FM Radio Station 2 blue flashes every
13. ial and Call Reject features Full duplex calls allow you to speak and hear the other party speak simultaneously INTRODUCTION CONTENTS OF RETAIL BOX lt Volume Up Charging Jack Volume Down CTRL Control Button Power On Power Off e Answer End MC Multi Connection e Radio On Off change stations e Initiate Terminate Buddy Intercom call with Primary or Secondary Buddy Helmet Clamp Right Speaker OCO long cord gt no a Sliding Plate Microphone tisi Left Speaker short cord NOTE The use of two speakers may be illegal in certain jurisdictions Please check the local regulations and act accordingly eee QGQ2_A5_021 indd 2 2 19 08 1 51 45 PM CONTENTS OF RETAIL BOX BEFORE USING Wall Charger Allen Wrench Velcro Pads Extension Pad Carry Pouch Microphone Sponge User Guide including Warranty and Registration form IMPORTANT The scala rider Q2 is a water resistant device designed for use under moderate rain or snow conditions However the headset is not waterproof and should not be used under severe weather conditions The cover tongue protecting the Charging Jack should be kept tightly closed at all times to prevent moisture from entering the device Make sure that the headset is fully charged for at least five hours before initial use 1 Connect the wall charger to the headset s Charging Jack located between the two Volume
14. nd receive calls through the headset you must now pair your mobile phone to your GPS device by following your GPS ATTACHING and or mobile phone s instructions Slide the headset downwards along the NOTE If the Pairing process is not completed within two sliding panel until a clicking sound indicates minutes the headset will return to Standby mode that the headset is locked in place REMOVING Your headset can be removed for Press here to remove charging and storage by pressing The microphone speaker clamp must be mounted onto the your finger gently against the tab helmet Once mounted the headset unit can be attached or and sliding the headset up with detached from the microphone speaker clamp at any time the other hand We recommend that you remove the Attaching the Clamp to the Helmet headset from the helmet when not in use 1 Use the enclosed Allen Wrench to Allen Wrench loosen the two screws on the Back _ Plate Back Plate 2 Slide the Back Plate between the internal padding and the external shell of the helmet If the external shell is too thick use the supplied plastic Extension Pad by loosening the screws and fitting the Extension Pad between the Back Plate and the main body of the clamp The microphone must be positioned vertically not horizontally in front of the center of the mouth with the yellow sticker pointing towards the mouth Attach the speakers to the Velcro inside your helmet opposite y
15. ntil both sides are quiet for 30 seconds or MC BUTTON CONNECT Single tap the MC Button A Buddy Intercom call will be established To end the Buddy Intercom call single tap the MC Button again To start a Buddy Intercom call with the Secondary Buddy while the headset is on Standby MC BUTTON CONNECT MC Button Double tap the MC Button A Buddy Intercom call will be established To end the Buddy Intercom call double tap the MC Button again NOTE When using a scala rider Headset as a Passenger headset Voice Connect Intercom can be initiated only by the scala rider Q2 headset Manual Connect Intercom can be initiated from either headset Failed Connection On the scala rider Q2 if you attempt to start a Buddy Intercom call with a Buddy that is already on a Phone GPS Intercom call you will hear a double beep indicating the Buddy is busy Reconnecting the Intercom If the scala rider Q2 and its Intercom Buddy headset go out of range and disconnect from each other the scala rider Q2 will automatically try to reconnect to its Intercom Buddy for five minutes a fp QGQ2_A5_021 indd 7 2 19 08 1 52 05 PM C AR DO scala rider 02 You can manually reconnect at any time by pressing the MC Button single tap for Primary Buddy and double tap for Secondary Buddy Receiving Intercom calls If you are not speaking with any one once the other party tries to initiate a Buddy Intercom call the call will
16. o the phone after pairing is complete The scala rider Q2 headset will automatically connect to the last phone connected to the headset SET UP FOR BLUETOOTH GPS DEVICE PAIRING If you have a Bluetooth enabled GPS device and would like to transmit navigation instructions and sounds from the GPS device through the headset s speakers you must first pair your headset to the GPS device NOTE Not all Bluetooth enabled GPS devices allow connections to Bluetooth headsets like the scala rider Q2 Please consult your GPS device s User Manual for more information TO PAIR THE SCALA RIDER Q2 TO A BLUETOOTH GPS DEVICE 1 Turn on your GPS device 2 With the scala rider Q2 headset turned ON press and hold the CTRL Button for at least six seconds until the Red and Blue Lights begin rapidly alternating SS QGQ2_A5_021 indd 5 2 19 08 1 51 57 PM 3 Search for Bluetooth headsets on your GPS device by following 3 Adjust the clamp s location so the device s instructions Please consult your GPS device s User that the microphone is located Manual for more information in front of the center of your 4 If your GPS device prompts for a PIN or Passkey enter 0000 mouth with the yellow sticker four zeros pointing towards your mouth and MCO INCORRECT 5 Your GPS device will confirm that pairing has succeeded The A U ee an headset will begin flashing slowly in Blue 6 If you wish to use a Bluetooth mobile phone to make a
17. one NOTE If you have a compatible Bluetooth GPS device you wish to use with the scala rider Q2 please skip this step and continue ahead to STEP 4 SET UP FOR BLUETOOTH GPS DEVICE Pairing is a one time process Once the headset is paired to a specific mobile phone during this Setup Procedure they will remain paired and automatically recognize each other whenever they are within range If the connection between the phone and headset is lost tap the CTRL button to reconnect the devices TO PAIR THE SCALA RIDER Q2 TO A BLUETOOTH MOBILE PHONE 1 Turn on your phone and make sure its Bluetooth function is activated 2 With the scala rider Q2 headset turned ON press and hold the CTRL Button for at least six seconds until the Red and Blue Lights begin rapidly alternating 3 Search for Bluetooth devices on your phone by following the phone s instructions Please consult your phone s User Manual for more information 4 After a few seconds the phone will list the scala rider Q2 as a discovered device Select it and follow your phone s instructions to accept the pairing 5 When prompted enter 0000 four zeros as your PIN or passkey 6 Your phone will confirm that pairing has succeeded and the headset will begin flashing slowly in Blue NOTE If the Pairing process is not completed within two minutes the headset will return to Standby mode With some mobile phones you may need to tap the CTRL button to connect the headset t
18. option below Disclaimer of Warranty CARDO DISCLAIMS ALL EXPRESS AND IMPLIED WARRANTIES WITH REGARD TO THE ENCLOSED DEVICE INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND NON INFRINGEMENT THE DEVICE AND ITS ACCESSORIES ARE PROVIDED AS IS AND AS AVAILABLE WITHOUT WARRANTY OF ANY KIND BEYOND THOSE ASSUMED IN THE ENCLOSED MANUAL Limitation of Liability IN NO EVENT SHALL CARDO BE LIABLE FOR ANY SPECIAL INDIRECT PUNITIVE INCIDENTAL EXEMPLARY ORCONSEQUENTIALDAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM THE USE OF THE DEVICE WHETHER BASED ON BREACH OF CONTRACT TORT INCLUDING NEGLIGENCE PRODUCT LIABILITY OR OTHERWISE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES YOU ACKNOWLEDGE AND AGREE THAT THE LIMITATIONS SET FORTH ABOVE ARE FUNDAMENTAL ELEMENTS OF THIS AGREEMENT AND THE DEVICE WOULD NOT BE PROVIDED TO YOU ABSENT SUCH LIMITATIONS SOME STATE STATUTES MIGHT APPLY REGARDING LIMITATION OF LIABILITY RETURN FOR FULL REFUND IF YOU ARE UNWILLING TO ACCEPT AND AGREE TO THE ABOVE CONDITIONS YOU MAY RETURN THIS DEVICE TO CARDO FOR A FULL REFUND PROVIDED THAT YOU DO SO NO LATER THAN 7 BUSINESS DAYS FOLLOWING THE PURCHASE OF THE DEVICE proof of purchase required AND SUBJECT TO THE WRAPPING BE ING INTACT WHEN DOING SO PLEASE REFER TO THIS SECTION BY NOT RETURNING THE DEVICE FOR REFUND WITHIN THE PE RIOD PROVIDED YOU ARE EXPLICITLY IN AGREEMENT WITH
19. or air jointly referred to as Vehicle requires your complete and undivided attention Cardo Systems Inc including its Officers Directors Affiliates Parent Company Representatives Agents Contractors Sponsors Em ployees Suppliers and Resellers jointly referred to as the Company or Cardo strongly advises you to take all necessary precautions and remain alert to the traffic weather and road conditions if you choose to use the scala rider Q2 headset including all derivative models irrespective of its commercial name or branding the Device and stop your Vehicle on the roadside prior to initiating or receiving calls Any publications advertise ments announcements or similar notes that refer to using the Device while riding a Vehicle are solely intended to address its technical capabilities and should not be misconstrued as if encouraging users to operate the Device while actively involved in traffic By way of purchasing this Device and not returning it for a full refund see below you are irrevocably releasing indemnifying from any liability loss claim and expense including attorneys fees and holding Cardo harm less for any bodily injuries harm or death as well as losses or damages in goods to any Vehicles including your own or to any property or asset that belong to you or to third parties any of which may result from using the Device under any circumstances or conditions and irrespective of jurisdic
20. our ears short speaker cord for left ear amp long speaker cord for right ear or use the supplied Velcro pads QGQ2_A5_021 indd 6 2 19 08 1 52 02 PM SETUP AND CONFIGURATION scala rider 02 c NARDO GENERAL USAGE GENERAL FUNCTIONS DESIRED RESULT REQUIRED ACTION Turn on the Press the CTRL Button steadily for at least three headset seconds Turn off the Press the CTRL Button steadily for at least three headset seconds Increase the Short press the Volume Up Button volume Decrease the volume Short press the Volume Down Button AGC Automatic Gain Control In addition to manual Volume Control the scala rider Q2 will automatically increase and reduce its volume according to ambient noise and driving speed AUDIO SOURCES AND PRIORITIES The different Audio Sources that are connected to the scala rider Q2 are prioritized as follows Highest 1 Mobile phone Audio GPS device Incoming outgoing calls GPS audio and navigation instructions 2 Primary Buddy Audio and Secondary Buddy Audio Lowest 3 FM Radio A high priority Audio Source will always interrupt any lower priority Audio Source Le Mobile phone call interrupts Intercom call Intercom call interrupts FM Radio Making Intercom calls To start a Buddy Intercom call with the Primary Buddy while the headset is on Standby you can either VOICE CONNECT Start talking A Buddy Intercom call will be established and stay on u
21. specific operating instructions for satisfying RF exposure compliance This transmitter must not be co located or operating in conjunction with any other antenna or transmitter e _ __ __ m QGQ2_A5_021 indd 10 2 19 08 1 52 08 PM NOTICES scala rider02 CARDO European CE Notice The scala rider Q2 headset the Product is in conformity with the following essential requirements of Council Directive 1999 5 EC referred to as R amp TTE Directive Articles 3 1a 3 1 6 and 3 2 The Product is manufactured in accordance with Annex Il of the above directive Declaration of Conformity DOC The scala rider Q2 headset is compliant with and adopts the Bluetooth Specification 2 0 and has successfully passed all interoperability tests that are specified in the Bluetooth specification However interoperability between the device and other Bluetooth enabled products is not guaranteed WAIVER AND GENERAL RELEASE By using the scala rider Q2 you will waive substantial legal rights including the right to sue Please read the following carefully before using the device If you do not accept all terms of this agreement you should immediately return the product for a full refund By using the headset you agree to be bound to this agreement and forfeit the right to sue Using a communication device while riding a motorcycle scooter moped ATV quad bike or any other vehicle or equipment whether on land water
Download Pdf Manuals
Related Search