PG5 User Manual - Automation Products Group, Inc.
Contents
1. PG5v108 hex created 11 15 09 gt Fixed Bar Graph when recalibrating gauge using the range function in the menu gt Fixed Glitch with Updating Range and re zeroing gauge in Mode 000 PG5v109 hex created 12 11 09 gt Fixed Glitch with entering mode 2 and returning to mode 3 for special calibration units which changed the units of measure gt Fixed Hi and Low resolution glitch with different units of measure Automation Products Group Inc APG PET Behe APG Providing tailored solutions for measurement applications Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 25 PG5 APG Automation Products Group Rev A1 3 10 1025 West 1700 North Logan on 84321 Phone 435 753 7300 Fax 435 753 7490 www apgsensors com CE DECLARATION OF CONFORMANCE PG 5 MODEL DIGITAL PRESSURE GAUGE Prepared By Test Specification Test Method Manufacturer Test Location 1 CERTIFICATION I HEREBY CERTIFY THAT March 30 2009 Elden Tolman Product Development Engineer Automation Product Group Inc 1025 West 1700 North Logan UT 84321 EN 61326 2002 ICE 61000 Automation Products Group Inc 1025 West 1700 North Logan UT 84321 815 West 1800 North Logan UT 84321 The measurements shown in this test report were made in accordance with the procedures given in European Council Directive 89 336 EEC The equipment was passed and the test performed according to European2. 21 23 Firmware Release Notes ccccccccccccccccccceceessssssssseeees 24 25 CE Declaration of Conformance ccccessessttssennensees 26 27 APG Automation Products Group Inc APG Providing tailored solutions for measurement applications 2 Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev A1 3 10 PG5 e Warranty and Warranty Restrictions APG warrants its products to be free from defects of material and workmanship and will without charge replace or repair any equipment found defective upon inspection at its factory provided the equipment has been returned transportation prepaid within 18 months from date of shipment from factory THE FOREGOING WARRANTY IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES NOT EXPRESSLY SET FORTH HEREIN WHETHER EXPRESSED OR IMPLIED BY OPERATION OF LAW OR OTHERWISE INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE No representation or warranty express or implied made by any sales representative distributor or other agent or representative of APG which is not specifically set forth herein shall be binding upon APG APG shall not be liable for any incidental or consequential damages losses or expenses directly or indirectly arising from the sale handling improper application or use of the goods or from any other cause relating thereto and APG s liability hereunder in any case is expre
3. No degradation of performance or loss of function is allowed below the performance level specified by the manufacturer when the device is used as intended The performance level may be replaced by a permissible loss of performance During the test degradation of performance is allowed If the minimum performance level or the permissible performance loss is not specified by the manufacturer then either of these may be derived from the product description and documentation and what the user may reasonably expect from the device if used as intended Performance Criteria C Temporary loss of function is allowed provided the function is self recoverable or can be restored by the operation of controls Automation Products Group Inc APG APG Providing tailored solutions for measurement applications Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 27 PRODUCTS GRO UP INC APG Providing tailored solutions for measurement applications APG Automation Products Group Inc Tel 1 888 525 7300 1 435 753 7300 Fax 1 435 753 7490 e mail sales apgsensors com www apgsensors com Automation Products Group Inc 1025 W 1700 N Logan UT 84321 To order additional copies of this manual ask for APG part number PN9003384 Rev A1 3 10
4. Off Button Primary Function Press and hold for 1 second to turn on off the gauge Secondary Function Press once to access the main setup menu Z Button Primary Function Press to zero the gauge reading the reading must be less than 5 of full scale in order to zero the gauge Secondary Function Cycles through the options in the setup menus S Button Primary Function Cycles between the current maximum and minimum pressure readings Secondary Function Used to accept the displayed option while in the setup menus Secondary Function Resets the peak hold reading when the peak hold feature is enabled APG Automation Products Group Inc ase gr APG Providing tailored solutions for measurement applications 4 Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev A1 3 10 PG5 PSI FULL ACCESS MENU YES BAR KPA CUSTOM ONLY CUSTOM MBAR INHG INH20 MMHG MAXMIN z S lt 120 psi SELECT MULTIPLIER PSI BAR KPA CUSTOM KGCM 2 CUSTOM ONLY MPA FTH20 UNITS P HOLD OFF CMHG ADVSET AUTO OFF 2 MIN 4 MIN 8 MIN 16 MIN 32 MIN DEC PL HI RES LO RES SAMPLE SLOW MEDIUM FAST BAR 0 SET BAR GRAPH 0 BAR100 SET BAR GRAPH 100 DEFAULT SET RANGE ALSET SET ANALOG LOW SET PRESSURE AH SET SET ANALOG HIGH SET PRESSURE ALCAL SET ANALOG LOW CALIBRATION AHCAL SET ANALOG HIGH CALIBRATION z fe Aut
5. P HOLd When the Peak Hold is enabled the gauge will display the peak or maximum pressure reading since the gauge was powered on or the Max Min value was reset NOTE 1 When the Peak Hold feature is enabled a small box containing the words PEAK HOLD will be displayed in the upper left corner of the display Options Off or On Enabling the Peak Hold feature Step 1 Press the On Off button to enter the main setup menu Step 2 Press Z to cycle through the options until P HOLd is displayed Step 3 Press S to access the Peak Hold setting options Step 4 Press Z to toggle between OFF and ON Step 5 Press S to apply the displayed setting and return to main setup menu NOTE 2 The peak value can be reset by pressing S with the Peak Hold function enabled Automation Products Group Inc PG APG Providing tailored solutions for measurement applications i Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 11 PG5 Rev A1 3 10 e Advanced Settings AdVSET The Advanced Settings menu is used to customize the LCD display and to setup any optional features such as an analog output Auto Off AUTO This function is applicable to battery powered units only The Auto Off feature allows the user to designate the time of inactivity no buttons pushed until the gauge automatically powers down Options 2 MIN 4 MIN 8 MIN 16 MIN 32 MIN and OFF NOTE Selecting OFF disables t
6. adjustment to the Menu gt Added Range adjustment in the Menu gt Added Modes to Lockout the Menu and give limited access PG5v104 hex created 4 27 2009 gt Changed how Units are displayed when other than psi only that unit is displayed PG5v105 hex created 5 27 2009 gt Fixed conversion problems with units ftH20 cmHg gt Fixed Bar Graph zero and Full Scale to scale to the right pressure gt Fixed High and Lo Res for the different units and to have a dummy zero for correct units APG Automation Products Group Inc s age APG Providing tailored solutions for measurement applications 24 Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev A1 3 10 PG5 Firmware Release Notes continued PG5v106 hex created 6 19 2009 gt Renamed the SETUP options displayed for bargraph and analog output setup gt Made Max reading not reset using shortcut only allowed in MENU Reset gt By pressing S while not in Menu the max then min values are displayed gt Added Decimal Place while setting the bargraph to the psi equivalent gt Added Decimal Place for Analog Output Set points gt Renamed SETUP to ADVSET in Menu gt When changing range the value then overwrites the default multiplier for field calibration PG5v107 hex created 8 12 09 gt If Tare is enabled and not in the menu the Z button will rezero the pressure reading gt Added Units of Measure TONS for customer
7. APG Providing tailored solutions for measurement applications 8 Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev A1 3 10 e Units of Measure PG5 UNITS Allows the user to select the unit of measure to be displayed as the pressure reading Options For gauges over 120 psi PSI bAR KPA CUSTOM KGCM 2 MPA FTH20 cmHG pounds per square inch bar kilopascals see Using Custom Units on next page kilograms per cubic centimeter megapascals feet of water 60 F centimeters of mercury For gauges less than 120 psi PSI bAR KPA CUSTOM mbAR INHG INH20 mmHG pounds per square inch bar kilopascals see Using Custom Units on next page millibar inches of mercury inches of water 60 F millimeters of mercury Setting the Unit of Measure Step 1 Press the On Off Step 2 Press Z to cycle button once to enter the main setup menu through the options until UNITS is displayed Step 3 Press S to access the Units options Step 4 Press Z to cycle through setting options until the desired unit of measure is displayed Step 5 Press S to apply the setting and return to the main setup menu Automation Products Group Inc PG APG Providing tailored solutions for measurement applications Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 9 PG5 Rev A1 3 10
8. Notes PG5v100 hex Created 1 20 2009 First Release of Software PG5V101 hex Created 2 13 2009 gt Updated Zero function to read NOZERO when more than 5 of Full Scale gt Updated Tare function to read NOTARE when more than full scale and if gauge is in TARE T5 segment instead of T1 and shuts off when greater than full scale gt Fixed On Off button on Power Up to wait to be released before going into the Menu PG5v102 hex Created 3 16 2009 gt Added different sampling rates selectable from the Menu slow medium fast gt Disabled the lo res option for units with no decimal place in reading gt Fixed Peak Hold to Reset by pushing Select Button to reset the max value to the current reading gt Fixed the Leading Zeros when Peak Hold enabled and when using the Custom Multiplier in the Menu gt Locked Menu has peak hold enable disable with Select button not in Menu Menu has Units gt Ibs kg Newton gt Can Zero Reading Z button gt Fixed External Power Auto_Off Option and Sampling Rate gt Fixed ON OFF Button when Auto_Off enabled it went into the MENU reset the Flag when Auto Off shutdown gt Reset Auto Off timer every time the Zero or Select Button are pushed PG5v103 hex 4 7 2009 gt Added 4 options to setup the analog output from the menu and appear only with ouputs enabled gt Added fsw to units and changed to lockout all other units when calibration to other unit besides psi gt Added Bar Graph Zero and Full Scale
9. Operator s Manual PG 5 Full Access DOC 9003384 Rev A1 3 10 Automation Products Group Inc APG Providing tailored solutions for measurement applications Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com E mail sales apgsensors com PG5 Rev A1 3 10 Table of Contents I oe accel A EEA E EA A ERE 3 Programming the PGS msssrroriiasneiriiiieiiiiiier iiaiai iie 4 19 Menu Flow Chatt soooooaaaoeennnnnannnnnnnnnnnnnne nennen 5 Changing the Mode Setting ccccceceeeeeeeeseeesnsnnessnsssaees 6 Accessing Exiting the Setup Menu ssssssssssessssseeeee 7 Maximum Minimum Function sisisceciserixeciserixereiesosssssvinsvsenss 8 UniS OF WAS rosies tee 9 Using Custom UNG eo a sscensctespreuseeccerltee neea 10 Peak Hold Feature or5 c c 255 eee eee eee 7 Advanced SOTHAOG asset siossiade soc caddesaeicgrecdieceaiidueseerale 12 18 AUO aoi mierina a eee A EEE A ee A mrt oe 12 Decimal Place sinus nese meres ps ssn ro din Sinn oci nai 13 Sample Rale eain cheba hats AARNE ONT 14 Bar GrapPeirena trenani tastes 15 Range FG MISUI CIM sacs ol stinnsitatsiaastite dscns itedinmaesngitayaueeasas 16 Analog SEIDOINS essri tis dadidyitienananaxanasdnars 17 Analog Calibration raihsacemscedascaiis discs ais aint acyccctaent 18 Tare PRBS ais st55 ig hata icins Senatsesntite conten econ en rE 19 105 2 16 a ee nee PR OPER nA Ra TES REREAD RE Dn 20 Wiring the gl Ge Seeeenerener mate arm r tr mT TUne rR ene tr en yer ye
10. Standard EN 61326 2002 using method ICE 61000 aK Product Line Manager APG 4 3 09 Date Automation Products Group Inc APG Providing tailored solutions for measurement applications 26 Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev A1 3 10 PGS 1025 West 1700 North Logan UT 84321 Phone 435 753 7300 Fax 435 753 7490 wwwapgsensors com 2 SUMMARY OF RESULTS The PGS model digital pressure gauge has been found to be fully compliant with the following standards and specifications Radiated Emissions Radiated Immunity EN 61326 Class A 2002 EN 61326 2002 Pass EN 61326 Annex A 3 PERFORMANCE CRITERIA 3 1 3 2 3 4 Pass In the case of Radiated Emissions no significant readings were observed Performance Criteria A The device will continue to operate as intended No degradation of performance or loss of function is allowed below the performance level specified by the manufacturer when the device is used as intended The performance level may be replaced by a permissible loss of performance If the minimum performance level or the permissible performance loss is not specified by the manufacturer then either of these may be derived from the product description and documentation and what the user may reasonably expect from the device if used as intended Performance Criteria B The device will continue to operate as intended after the test
11. Using Custom Units CUSTOM The Custom Units setting allows the user to display a volumetric weight by applying a conversion factor to the pressure reading NOTE The conversion factor must be calculated using Pound per Square Inch psi as the base unit of measure Setting the Custom Units feature Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Step 9 Step 10 Calculate the conversion factor from psi to the desired unit of measure Press the On Off button once to enter the main setup menu Press Z to cycle through the options until UNITS is displayed Press S to access the Units setting options Press Z to cycle through the Units options until CUSTOM is displayed Press S to access the Custom Units setting A 5 digit conversion factor will appear with the first digit flashing Press Z to change the value of the flashing digit options 0 9 Press S to accept the flashing digit and advance to the next digit repeat steps 7 and 8 as necessary After the last digit is accepted by pressing S use Z to scroll through the custom units of measure LBF KN LBS KG and NEWTON Press S to accept the custom unit and return to the main setup menu PH Automation Products Group Inc age APG Providing tailored solutions for measurement applications Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev A1 3 10 PG5 e Peak Hold
12. ext digit repeat steps 7 and 8 until the desired 0 reading is fully entered After the last digit is accepted by pressing S the display will return to the main options menu Press S to reenter the Advanced Settings menu Press Z to cycle through the options until BAR100 is displayed Repeat Steps 5 7 to enter the Bar Graph 100 value Automation Products Group Inc APG Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 15 PG5 Rev A1 3 10 Full Scale Range Adjust RANGE Allows the user to adjust the reading at full scale pressure The reading can be adjusted by 10 full scale NOTE The pressure reading must be within 5 of the full scale value in order to make Range adjustments For example a 1000 psi gauge would need to be reading between 950 psi and 1050 psi in order to adjust the Range feature If the reading is not within 5 of full scale NOAdJU No Adjustment will be displayed when trying to adjust the Range Adjusting the Full Scale Range Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Ensure that the pressure reading is within 5 of full scale Press the On Off button to enter the main setup menu Press Z to cycle through the options until AdVSET is displayed Press S to access the Advanced Settings menu Press Z to cycle through the options until RANGE is displayed Press S to enter the Range adjust mode Press Z to increa
13. he Auto Off feature the gauge will then remain powered indefinitely as long as there is sufficient voltage being supplied 3 3V Setting the Auto Off feature Step 1 Press the On Off button to enter the main setup menu Step 2 Press Z to cycle through the menu options until AdVSET is displayed Step 3 Press S to enter the Advanced Settings menu Step 4 Press Z to cycle through the menu options until AUTO is displayed Step 5 Press S to access the Auto Off setting options Step 6 Press Z to cycle through setting options until the desired setting is displayed Step 7 Press S to apply the setting and return to main setup menu PH Automation Products Group Inc age APG Providing tailored solutions for measurement applications 12 Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev A1 3 10 PG5 Decimal Place dEC PL The reading can be set to display in High Resolution HI RES or Low Resolution LO RES mode Switching between high and low resolution will shift the displayed reading by one decimal place position NOTE When Low Resolution mode is enabled on a gauge with 0 decimal place positions the display will increment in factors of 10 Options HI RES high resolution or LO RES low resolution Setting the Decimal Place feature Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 APG Providing tailored solutions for measure
14. ment applications Press the On Off button to enter the main setup menu Press Z to cycle through the menu options until AdVSET is displayed Press S to enter the Advanced Settings menu Press Z to cycle through the options until dEC PL is displayed Press S to access the Decimal Place setting options Press Z to cycle between HI RES high resolution and LO RES low resolution Press S to apply the displayed setting and return to main setup menu Automation Products Group Inc APG HHG zs Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 13 PG5 Rev A1 3 10 Sample Rate SAMPLE Adjusts the rate at which the gauge takes sample readings NOTE Setting the Sample Rate to SLOW will help preserve battery life when applicable and will also help to smooth rapidly fluctuating readings Options SLOW 4x second MEdIUM 8x second FAST 16x second Setting the Sample Rate feature Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Press the On Off button to enter the main setup menu Press Z to cycle through the options until AdVSET is displayed Press S to access the Advanced Settings menu Press Z to cycle through the options until SAMPLE is displayed Press S to access the Sample Rate setting options Press Z to cycle through the setting options until the desired setting is displayed Press S to apply the displayed setting and re
15. omation Products Group Inc APG APG Providing tailored solutions for measurement applications g Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 5 PG5 Rev A1 3 10 Accessing the Mode Setting Step 1 Simultaneously press and hold the On Off button and the S button for approximately 3 seconds This will bring up the 3 digit mode number Step 2 Enter the desired mode number see mode definitions below by using Z to change the value of the flashing digit and S to advance to the next digit Mode Definitions Mode 000 Full Access Provides access to all menu settings If no buttons are pushed for 1 minute the gauge will revert back to Mode 003 factory default Mode 002 Limited Access Menu is locked Z button zeros the reading S cycles between the Max and Min readings On Off functions only on battery powered gauges Mode 003 Factory Default Full access except Full Scale Calibration is locked Mode 005 Locked Access All buttons locked except the on off button on battery powered gauges Automation Products Group Inc APG Providing tailored solutions for measurement applications 6 Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev A1 3 10 PG5 Z Button On Off Button S Button a a PH Logan UT 84321 BEER 888 525 7300 Automation Products Group Inc Accessing the Main Setup Menu Step 1 With gauge p
16. options Step 4 Press Z to toggle between OFF and ON Step 5 Press S button to apply the displayed options and return to main setup menu ESAT NOTE 1 When tare function is enabled the T5 symbol will appear in the lower left corner of the display WARNING Do NOT disconnect the gauge from the pressure fitting while the tare function is enabled The gauge may still be under pressure even though the reading shows 0 NOTE 2 If the maximum gross full scale pressure value is reached while the Tare feature is enabled the PGS will automatically disable the Tare feature and return to reading the gross pressure in order to help prevent the user from unwittingly overpressuring the gauge Automation Products Group Inc APG PET Bae APG Providing tailored solutions for measurement applications Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 19 PG5 Rev A1 3 10 Default dEFAUL Used to reset the gauge to the factory default settings Resetting the gauge to factory default settings Step 1 Press the On Off button once to enter the main setup menu Step 2 Press Z to cycle through the options until AEFAUL is displayed Step 3 Press S to access the Default options Step 4 Press Z to cycle between NO and YES Step 5 Press S to apply the displayed setting and return to main setup menu PH Automation Products Group Inc age APG Providing tailored sol
17. oss the load resistance with the output at 20mA Example If RL 250 ohm then drop is 0 02 Amps X 250 ohm 5 volts Therefore power supply minimum is 5 V 9 V 14 V NOTE 2 Completion of the earth ground Pin F is recommended for proper circuit protection Externally powered with 0 5 VDC or 0 2 VDC analog output EXCITATION A BE SUPPLY 6 Pin Connector B OUTPUT VOLTAGE c o OUTPUT EXCITATION F EARTH GROUND NOTE Completion of the earth ground Pin F is recommended for proper circuit protection Automation Products Group Inc APG Providing tailored solutions for measurement applications 22 Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev A1 3 10 PG5 Battery powered with 0 2 VDC output option The 0 2 VDC signal is accessed through a stereo jack connection on the back of the gauge 0 2 VDC Output Tip Output Body Center Tip mme _ Center Output Body No connection Note Not to scale NOTE 1 Do not connect to the stereo jack s case connection NOTE 2 To minimize the effect on the battery life the output should not be loaded with less than 100k ohms Automation Products Group Inc APG HH APG Providing tailored solutions for measurement applications i Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 23 PG5 Rev A1 3 10 Firmware Release
18. owered on press the On Off button once to enter the main setup menu Step 2 Press Z to scroll through menu choices max min units peak hold advanced settings tare default and exit Exiting the Main Setup Menu Step 1 While in the main setup menu press Z until EXIT is displayed Step 2 Press S to access the Exit options Step 3 Press Z to until YES is displayed Step 4 Press S to Exit the main setup menu and return to the standard operating mode Automation Products Group Inc PG HH APG Providing tailored solutions for measurement applications Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 7 PG5 Rev A1 3 10 e Maximum Minimum Reset MAXMIN Pressing the S button while in standard operating mode will cycle between displaying the current pressure reading the Maximum pressure reading and the Minimum pressure reading The maximum and minimum readings will be stored until the gauge is powered down or the max min readings are reset Resetting the Max Min readings Step 1 Press the On Off button once to enter the main setup menu Step 2 Press Z to cycle through the options until MAXMIN is displayed Step 3 Press S to access the Max Min reset options Step 4 Press Z to toggle between YES and NO until YES is displayed Step 5 Press S to reset the Max Min readings and return to the main setup menu APG Automation Products Group Inc ase gr
19. se the reading or press S to decrease the reading Press the On Off button to accept the adjusted reading and return to the main setup menu PH Automation Products Group Inc age APG Providing tailored solutions for measurement applications Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev A1 3 10 PG5 Analog Low AL SET amp Analog High AH SET Setpoints Allows the user to define the reading values associated with the Low Analog signal i e 4mA or OV and the High Analog signal i e 20mA 2V or 5V NOTE The analog signal can be spanned over any portion of the pressure range and can also be inverted by setting the Analog Low Setpoint as the higher pressure value Negative pressure values can also be used as either the Analog High or Analog Low Setpoints Setting the Analog Signal Span Step 1 Press the On Off button once to enter the main setup menu Step 2 Press Z to cycle through the options until AdVSET is displayed Step 3 Press S to access the Advanced Settings menu Step 4 Press Z to cycle through the options until AL SET is displayed Step 5 Press S to access the Analog Low setpoint value A 5 digit number will appear with the first digit flashing Step 6 Press Z to change the value of the first flashing digit options 0 9 or Step 7 Press S to accept the value of the flashing digit and advance to the next digit repeat
20. ssly limited to the repair or replacement at APG s option of goods Warranty is specifically at the factory Any on site service will be provided at the sole expense of the Purchaser at standard field service rates All associated equipment must be protected by properly rated electronic electrical protection devices APG shall not be liable for any damage due to improper engineering or installation by the purchaser or third parties Proper installation operation and maintenance of the product becomes the responsibility of the user upon receipt of the product Returns and allowances must be authorized by APG in advance APG will assign a Return Material Authorization RMA number which must appear on all related papers and the outside of the shipping carton All returns are subject to the final review by APG Returns are subject to restocking charges as determined by APG s Credit Return Policy Automation Products Group Inc PG APG Providing tailored solutions for measurement applications Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 3 PG5 Rev A1 3 10 Programming the PG5 Z Button On Off Button S Button Battery Meter Bar Graph Each of the three buttons on the PG5 performs multiple functions The primary function applies when in standard operating mode The secondary functions are used for programming operations and when special features such as Peak Hold are enabled On
21. steps 7 and 8 until the desired Analog Low reading is fully entered After the last digit is accepted by pressing S the display will return to the main options menu Step 8 Press S to reenter the Advanced Settings menu Step 9 Press Z to cycle through the options until AH SET is displayed Step 10 Repeat Steps 5 7 to enter the Analog High setpoint value Automation Products Group Inc APG PET Bae APG Providing tailored solutions for measurement applications Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 17 PG5 Rev A1 3 10 Analog Low AL CAL amp Analog High AH CAL Calibration Allows the user to calibrate or trim the endpoints of the analog signal output i e 4mA amp 20mA or OV amp 2V 5V Calibrating the Analog Signal End Points Step 1 Use acalibrated meter to monitor the analog output signal Step 2 Force a low analog output signal i e 4mA or OV either by adjusting the applied pressure or by adjusting the Analog Setpoints see Analog Setpoints on page 18 for details Step 3 Press the On Off button once to enter the main setup menu Step 4 Press Z to cycle through the options until AdVSET is displayed Step 5 Press S to access the Advanced Settings menu Step 6 Press Z to cycle through the setup options until AL CAL is displayed Step 7 Press S to access the Analog Low Calibration value A 5 digit number will appear with the firs
22. t digit flashing Step 8 Press Z to change the value of the flashing digit NOTE Increasing this 5 digit number will increase the output signal Changing the digit farthest to the left will produce the coarsest adjustment while each successive digit moving to the right will cause subsequently finer adjustments to the output signal Step 9 Press S to accept the value of the flashing digit and advance to the next digit repeat steps 7 and 8 until the desired Analog Output Signal displayed ont he meter After the last digit is accepted by pressing S the display will return to the main setup menu Step 10 Press S to reenter the Advanced Settings menu Step 11 Press Z to cycle through the options until AH CAL is displayed Step 12 Repeat Steps 5 7 to adjust the Analog High Calibration value PH Automation Products Group Inc age APG Providing tailored solutions for measurement applications 18 Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev A1 3 10 PG5 e Tare TARE Enabling the Tare function will set the current pressure reading as the zero reference pressure in order to measure a net change in pressure as opposed to measuring the gross pressure Enabling the Tare feature Step 1 Press the On Off button once to enter the main setup menu Step 2 Press Z to cycle through the options until TARE is displayed Step 3 Press S to access the Tare setting
23. turn to main setup menu PH Automation Products Group Inc age APG Providing tailored solutions for measurement applications Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev A1 3 10 PG5 Bar Graph 0 bAR 0 amp 100 bAR100 Settings Allows the user to define the reading values associated with 0 and 100 on the display bar graph Bars will appear disappear in 10 increments of the total span between the two values NOTE The 0 reference does not have to be the lower pressure setting 0 can be set as the higher pressure setting thereby causing the bar graph to increase as the pressure decreases Negative pressure settings can also be used as either the 0 or 100 reference points Setting the Display Bar Graph Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Step 9 Step 10 APG Providing tailored solutions for measurement applications Press the On Off button once to enter the main setup menu Press Z to cycle through the options until AdVSET is displayed Press S to access the Advanced Settings menu Press Z to cycle through the options until BAR 0 is displayed Press S to access the Bar Graph 0 value A 5 digit number will appear with the first digit flashing Press Z to change the value of the first flashing digit options 0 9 or Press S to accept the value of the flashing digit and advance to the n
24. utions for measurement applications 20 Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev A1 3 10 PG5 Wiring the PG5 Battery Replacement The battery is accessed by removing the single screw at the top of the battery cover on the back of the gauge NOTE Do not overtighten the screw when securing the battery cover Externally Powered No Output Externally powered gauges without an analog output are powered using an 1 8 inch stereo jack connector mate supplied on the back of the gauge The Tip connection is Power and the Center connection is Power WARNING Always turn off the supply power before inserting or removing the stereo jack plug Failure to do so can damage the gauge Supply Supply Body Center Tip Note Not to scale NOTE Do not connect to the stereo jack s case connection Automation Products Group Inc APG ope APG Providing tailored solutions for measurement applications Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 21 PG5 Rev A1 3 10 4 20 mA Option loop powered Process Controller aL EXCITATION Vin 6 Pin Connector EXCITATION p este c gz 4 20 mA D CURRENT LOOP F EARTH GROUND NOTE 1 The supply voltage must be sufficient to maintain a minimum of 9 VDC after dropping voltage acr
Download Pdf Manuals
Related Search