Phoenix AN0F Mobile NO DHCP SIP DIRECT_EN
Contents
1. AEQ PHOENIX AUDIOCODECS APPLICATION NOTE 0 F Connecting AEQ Phoenix Mobile units via Internet complex scenario configuration Through LOCAL network s DHCP not used manual NAT DIRECT SIP mode Adapted to Phoenix Mobile User Interface The most convenient and reliable way to connect an IP codec to a remote one through Internet is by means of a dedicated exclusive Internet access DSL cable modem In this application note a way to achieve the same result will be proposed when this is not possible as Internet access is shared with other equipments connected within a managed LOCAL LAN and DHCP is not available or convenient This application note describes the recommended procedure when AEQ SIP Proxy is not reachable or we don t want to use it and SIP signaling is used from end to end with no servers involved As we need to get access to Internet a shared resource in this case it is mandatory to contact the network administrator in order to have the required resources enabled and gather all the necessary information This document shows the specific steps to make this connection possible in the most general way possible although some verification procedures have been omitted in order to ease the reading and some particular situations may be easier to solve that the presented one For a detailed explanation of every step and for details on how to configure other options that may be more convenient for other cases the reading o2. 4 SENDING A TEST CALL TO PHOENIX MASTER We are going to go through the correct configuration of the system and prepare it to make a test call to a unit called phoenix Master and phoenix Master 2 codecs that AEQ maintains for our customers and that continuously transmits audio at the public IP address 212 170 163 189 Check that a set of headphones are connected to the front HP1 connection Main screen gt Menu gt ADVANCED gt 2 Contacts With the help of the user manual create a couple of new contacts with the following parameters Contact AEQMASTER_IP DIRSIP2 Module Type IP URI phoenixMaster2 212 170 163 189 Contact AEQMASTER_IP DIRSIP Module Type IP URI phoenixMaster 212 170 163 189 5061 and make a call In order to do so From the main screen Menu Select the Select contact line and choose Select contact AEQMASTER_IP DIRSIP2 or Select contact AEQMASTER_IP DIRSIP You can send the call by simply pressing the green key If the line Select contact presents a different name at its right just select this line and press select key The call book will be presented Just select AEQMASTER_IP DIRSIP or AEQMASTER_IP DIRSIP2 from the list press OK to close the list and then finally press the green key NOTE Have in mind that this Call book entry that is created in the unit by default APLICACIONES ELECTRONICAS QUASAR S A TEL 34 91 686 13 00 FAX 34 91 686 44 92 E mail aeqsales
3. optical and also acoustical if enabled will be activated at the destination codec that will either wait for the user to answer the call or automatically off hook if this mode is enabled and then establish the connection The LED next to TX PROG should become green lit and audio should be heard through the headphones The three first screen lines should be Connected lt equipment name gt lt remote IP_address lt coding scheme gt For more information and other configuration options please read the User Manual and Application Notes corresponding to other scenarios If you still have doubts please don t hesitate to contact one of our assistance services sat aeq es support aeaqbroadcast com APLICACIONES ELECTRONICAS QUASAR S A TEL 34 91 686 13 00 FAX 34 91 686 44 92 E mail aeqsales aeq es Web WWW aCq CU
4. Ether Otherwise please select this Highlight the Configure Interface line using the down arrow key press Select and configure the following e DHCP OFF Local IP type IP LOCAL address from 1 1 for example 172 26 5 59 Gateway type the Gateway IP address for Internet access from 1 4 For example 172 26 1 1 Mask type a valid Net Mask from 1 2 for example 255 255 0 0 DNS Server type a DNS IP address from 1 3 for example 172 26 1 1 SIP Proxy OFF Make sure that the STUN server is activated and with a valid address set as explained afterwards APLICACIONES ELECTRONICAS QUASAR S A TEL 34 91 686 13 00 FAX 34 91 686 44 92 E mail aeqsales aeq es Web WWW aeq eu 3 OTHER POINTS TO CHECK We are now going to quickly overview the rest of configuration menus where it is recommended to check that every parameter is correctly configured Coding Algorithm At the Wizard menu Sel Codec should be G722 for a start although you can change this at a later stage for better quality In order to change the coding algorithm by another pre selected one just select the Sel codec line press Select and select one within the new window shown In order to choose the particular coding modes in each list shown in the Sel codec menu go to Menu gt ADVANCED gt 6 Link profiles gt Select gt Options The audio routing will be most likely correct by default to send Mic 1 audio to the transmissi
5. aeq es Web WWW aCq CU AEQMaster_IP Module Type IP URI phoenixMaster sip aeq es allows connection through AEQ SIP server only with PROXY SIP option activated ON So it is not valid to connect to Phoenix Master test unit in this case DIRECT SIP mode and the above mentioned entries should be created e The top line at the screen displays usually very fast the status of the call and the different phases it goes through Calling Synchronizing and finally Connected e The second line shows AEQMASTER_IP DIRSIP2 o AEQMASTER_IP DIRSIP e The third line should show G722 or the current audio coding scheme If the remote unit is busy the top line will show Busy 486 e Verify that the LED at the side of TX PROG SYNC key is lit green as an indication that the communication has been successfully established and synchronized If the key above HP1 is activated illuminated and the corresponding fader is open the audio received from Phoenix Master should be heard at the headphones Once the connection is OK you can retry as many times as needed varying the selected audio coding scheme in order to get the best possible quality allowed by the network Wizard Menu gt Sel Codec The list of available coding algorithms can be created in Menu gt ADVANCED gt 6 Link Profiles gt Select 5 SENDING A CALL TO ANOTHER PHOENIX OR N ACIP COMPATIBLE CODEC The test call sent to Phoenix Master units has been automatic
6. ally answered In order to make a manual call to other codec you must configure the second one the same way as the first unit provided that it is also connected directly to a LAN with managed router If it is not just follow the corresponding Internet access application note Once the reporter equipment connects properly to AEQMaster_IP you can create for convenience new entries in the call book Menu gt ADVANCED gt 2 Contacts with the name and URI of the remote unit the same way it was done for Phoenix Master in the previous chapter and then easily make calls to them You can of course also send the calls without having previously created a Call Book entry from the main screen by pressing Menu to go to the Wizard Select the Call to line press Select and URI is selected Then type the desired destination URI in the line below select Enter URI then press OK and type the URI in For this APLICACIONES ELECTRONICAS QUASAR S A TEL 34 91 686 13 00 FAX 34 91 686 44 92 E mail aeqsales aeq es Web WWW aCq CU communications mode based on a SIP server you only need to introduce the name of the unit for example Phoenix_123 A URI for DIRECT SIP use has the following format lt codec_name gt lt public_IP_of_the_codec gt lt SIP port gt So if the unit configured as in this example is called from another unit they should dial as phoenix_123 212 170 180 170 5060 The call indications
7. f the rest of application notes as well as User Manual s chapter 4 is recommended 1 NETWORK ADMINISTRATION INVOLVEMENT We will need that the Network Administrator 1 Provides us with a valid internal IP within the local network for example 172 26 5 59 for sending SIP signaling as well as audio using RTP protocol Both IP will be the same in both cases and we will refer to it as LOCAL IP 2 Indicates us the Network Mask for example 255 255 0 0 3 Tell us the DNS server IP address for example 172 26 1 1 or a valid external DNS server for the country we are working at If it is not provided we will still be able to operate provided that we know the IP address of the SIP Proxy although it is always recommended to specify it by its DNS name 4 Provides the Gateway IP address as an example 172 26 1 1 APLICACIONES ELECTRONICAS QUASAR S A TEL 34 91 686 13 00 FAX 34 91 686 44 92 E mail aeqsales aeq es Web WWW aCq CU Indicates us the network Public IP address In most cases there will be a single public IP for SIP signaling and RTP traffic We will refer to it as PUBLIC IP for example 212 170 180 170 Opens the required ports for audio and signaling These ports are by default e SIP signaling PORT SIP LOCAL PORT 5060 e Ports for audio transmission and control RTP and RTCP protocols 5004 and 5005 respectively e STUN ports 3478 amp 3479 2 CONNECTING AND CONFIGURING THE EQUIPMENT The phy
8. on and send the received stream to HP1 headphone output You can however make sure of this from Menu gt ADVANCED gt 3 Audio Settings gt Select Configure the rest of parameters after reading the manual according to your particular needs DIRECT SIP configuration PROXY SIP OFF You can make sure that this is correct from the main screen Menu gt ADVANCED gt 5 Communications gt 3 SIP config gt 1 Parameters Check that user name is filled with a valid name for example phoenix_123 STUN Protocol 2 Activate ON This is important and recommended as it will ease connecting to other equipment that is behind a router in a local network 3 Server At the moment of writing this document the following STUN server is recommended stun voxgratia org IP 83 103 82 85 If the DNS Server field in the communications menu hasn t been configured you must substitute the STUN name by its IP 4 Port 3478 Press back key in order to go to 3 SIP config gt 2 Proxy and check 1 Activate OFF The rest of parameters within this screen are not applicable to this communication mode with no server involved APLICACIONES ELECTRONICAS QUASAR S A TEL 34 91 686 13 00 FAX 34 91 686 44 92 E mail aeqsales aeq es Web WWW aCq CU Press back in order to go to 3 SIP config go to 4 Call Settings and check that Media PORT is the one opened by the Network Administrator paragraph 1 6 5004 by default
9. sical connection will be done to a LAN port Connect the network cable to the LAN1 port at the back of the AEQ Phoenix Mobile Connect the other end to the Ethernet port to the router LAN port Connect at least a microphone and a pair of headphones to the front audio XLR connectors of the Phoenix Mobile Connect the power supply cable to the AEQ Phoenix Mobile If it is equipped with a battery pack and mains power is not available you can omit this step Press the ON button at the left side of AEQ Phoenix Mobile Verify that the main display is illuminated Verify at the back of the unit that the green LED at the right of the Ethernet port starts blinking indicating that the IP connection is active Configuring the Ethernet port and assignation of Program channel Make sure that we are selecting Program in the main screen the one representing faders and vumeters At the lower center area you should read Program Also by pressing MENU we enter the Wizard menu that should have a PROGRAM legend at the top center area If COORDINATION appears instead in any of both places just press Channel key and channel will be shifted to PROGRAM APLICACIONES ELECTRONICAS QUASAR S A TEL 34 91 686 13 00 FAX 34 91 686 44 92 E mail aeqsales aeq es Web WWW aCq CU Professional f Broadcast Main screen Wizard screen From main screen press Menu to access the Wizard menu Make sure that Select Interface shows IP
Download Pdf Manuals
Related Search