USER MANUAL E300BT
Contents
1. e Follow the steps described in this user manual see Charge and pair your headset on page 4 e Make sure that the LED light flashes blue and white alternately before you release the power on off button Do not stop holding the button if you see the blue LED only The mobile phone cannot find the headset e The headset may be connected to a previously paired device Turn off the connected device or move it out of range e Pairing may have been reset or the headset has been previously paired with another device Pair the headset with the mobile phone again as described in the user manual see Charge and pair your headset on page 4 Voice dialing or redialing does not work on my mobile phone Your mobile phone may not support this feature The other side cannot hear me on the mobile phone The microphone is muted Press volume track control button once to enable the microphone My Bluetooth headset is connected to a Bluetooth stereo enabled mobile phone but music only plays on the mobile phone speaker Refer to the user manual of your mobile phone Select to listen to music through the headset The audio quality is poor and crackling noise can be heard The Bluetooth device is out of range Reduce the distance between your headset and Bluetooth device or remove obstacles between them The audio quality is poor when streaming from the mobile phone is very slow or audio streaming does not work at a2. ONKYO eal Lit lt WD 2 lt 2 gt Contents 1 Important safety instructions 2 Hearing Safety 2 General information 2 2 Onkyo Bluetooth wireless headset 3 Box content 3 Other devices 3 Overview of your Bluetooth wireless headset 3 3 Charge and pair your headset 4 Charge the battery 4 Pair your headset 4 Multiple pairing 5 4 Use your headset 6 Connect the headset to a Bluetooth device 6 Manage your calls and music 6 5 Technical data 8 6 Notice 9 Declaration of conformity 9 Disposal of your old product and battery 9 Compliance with EMF 9 Trademarks 10 7 Frequently asked questions 11 EN 1 Important safety instructions Hearing Safety Danger To avoid hearing damage limit the time you use headphones at high volume and set the volume to a Safe level The louder the volume the shorter the safe listening time is Be sure to observe the following guidelines when using your headset e Listen at reasonable volumes for reasonable periods of time e Be careful not to adjust the volume continuously upwards as your hearing adapts e Do not turn up the volume so high that you can t hear what s around you e You should use caution or temporarily discontinue use in potentially hazardous situations e Excessive sound pressure from earphones and headphones can cause hearing loss e Using headphones with both ears covered while driving is not recommended and may be il
3. adset rie ol E Power on off music call control and NFC detection area 2 LED indicator 3 Microphone 4 Micro USB charging slot G Volume track control EN 3 3 Charge and pair your headset Charge the battery Note e Before you use your headset for the first time charge the battery for 5 hours for optimum battery capacity and lifetime Use only the original USB charging cable to avoid any damage e Finish your call before charging the headset as connecting the headset for charging will power the headset off 1 Plug one end of the USB cable into the charger or into the USB port of a computer 2 Plug the other end of the cable into the micro USB charging slot on the headset L gt When the headset is charging a white indicator light will be displayed L gt When the headset is fully charged the white light goes off Tip e Normally a full charge takes 2 hours Pair your headset The headset stores the last 4 devices in the memory If you try to pair more than 4 devices the earliest paired device is replaced by the new one There are two ways to pair your headset with your mobile phone 4 EN e Manual pairing e NFC pairing Manual pairing 1 Make sure that the headset is fully charged 2 Make sure that the headset is off 3 Press and hold the power on off button until the blue and white LED fla
4. blue LED flashes L gt The headset is reconnected to the last connected mobile phone Bluetooth device automatically EJ e If you turn on the mobile phone Bluetooth device or activate the Bluetooth feature after turning on the headset you have to reconnect the headset and mobile phone Bluetooth device manually e If your mobile phone Bluetooth device cannot reconnect automatically try to reconnect manually by clicking the headset s name again under the Bluetooth setting manual on your mobile phone Bluetooth device Note e If the headset fails to connect to any Bluetooth device within range in 5 minutes it will switch off automatically to save the battery life Manage your calls and music On off Task Button Operation Turnthe Power Press and hold for 2 headset on off seconds on Turn the Power Press and hold for 4 headset on off seconds off L gt The white LED is on for 1 5 seconds and then the headset is off Music control Task Button Operation Play or pause Music call Press music control once Adjust Volume track Press volume control once Skip forward Volume track Press and backward control hold Call control Task Button Operation Pick up hang Music Press once up a call call Reject an Music Press and incoming call call hold for 2 seconds Switch caller Music Press twice during a call call Mute unmute Volume Pres
5. ckaging easy to separate into three materials cardboard box polystyrene foam buffer and polyethylene bags protective foam sheet Your system consists of materials which can be recycled and reused if disassembled by a specialized company Please observe the local regulations regarding the disposal EN 9 of packaging materials exhausted batteries and old equipment Trademarks Bluetooth The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG Inc and any use of such marks by Gibson Innovations Limited is under license Onkyo is a registered trade mark of Gibson Brands Inc Other trademarks and trade names are those of their respective owners CSR s copyright and trademark notice 2013 CSR plc and its group companies The aptX mark and the aptX logo are trademarks of CSR plc or one of its group companies and may be registered in one or more jurisdictions N Mark The N Mark is a trademark or registered trademark of NFC Forum Inc in the United States and in other countries 10 7 Frequently asked questions My Bluetooth headset does not switch on The battery level is low Charge the headset cannot pair my Bluetooth headset with a mobile phone The Bluetooth is disabled Enable the Bluetooth feature on your mobile phone and turn on the mobile phone before you turn on the headset Pairing does not work Make sure the headset is in pairing mode
6. legal in some areas while driving e For your safety avoid distractions from music or phone calls while in traffic or other potentially dangerous environments General information To avoid damage or malfunction pE Caution Do not expose the headset to excessive heat Do not drop your headset e Headset shall not be exposed to dripping or splashing Do not allow your headset to be submerged in water e Do not use any cleaning agents containing alcohol ammonia benzene or abrasives e If cleaning is required use a soft cloth if necessary dampened with a minimum amount of water or diluted mild soap to clean the product e The integrated battery shall not be exposed to excessive heat such as sunshine fire or the like e Risk of explosion if battery is replaced by an incorrect type Replace only with the same or equivalent type About operating and storage temperatures and humidity e Operate or store in a place where temperature is between 15 C 5 F and 55 C 131 F up to 90 relative humidity e Battery life may be shorter in high or low temperature conditions 2 Onkyo Bluetooth wireless headset Box content USB charging cable ONKYO Quick start guide Other devices A mobile phone or device e g notebook PDA Bluetooth adapters MP3 players etc which supports Bluetooth and is compatible to the headset Overview of your Bluetooth wireless he
7. ll Make sure your mobile phone not only supports mono HSP HFP but also supports A2DP see Technical data on page 8 hear but cannot control music on my Bluetooth device e g play pause skip forward backward Make sure the Bluetooth audio source supports AVRCP see Technical data on page 8 For further support visit www onkyo headphones com 2015 Gibson Innovations Limited All rights reserved This product has been manufactured by and is sold under the responsibility of Gibson Innovations Ltd and Gibson Innovations Ltd is the warrantor in relation to this product Onkyo is a registered trade mark of Onkyo Corporation Other trademarks and trade names are those of their respective owners C 0890 HI E s ONKYO www onkyo headphones com
8. nd manufactured with high quality materials and components which can be recycled and reused a This symbol on a product means that the product is covered by European Directive 2012 19 EU H This symbol means that the product contains a built in rechargeable battery covered by European Directive 2013 56 EU which cannot be disposed of with normal household waste We strongly advise you to take your product to an official collection point to have a professional remove the rechargeable battery Inform yourself about the local separate collection system for electrical and electronic products and rechargeable batteries Follow local rules and never dispose of the product and rechargeable batteries with normal household waste Correct disposal of old products and rechargeable batteries helps prevent negative consequences for the environment and human health Remove the integrated battery Note Make sure the headset is disconnected from the USB charging cable before removing the battery If there is no collection recycling system for electronic products in your country you can protect the environment by removing and recycling the battery before disposing the headset Compliance with EMF This product complies with all applicable standards and regulations regarding exposure to electromagnetic fields Environmental information All unnecessary packaging has been omitted We have tried to make the pa
9. s volume the microphone track up and down in a call control button once at the same time Other headset indicator status Headset status Indicator The battery level is low The white LED flashes every 10 seconds for pairing The headset is ready The blue and white LED flashes alternately and connected not connected to a Bluetooth device The headset is paired The headset is on but The blue LED flashes every 8 seconds The blue LED flashes quickly EN 5 Technical data e Music time 7 5 hours e Talk time 8 hours e Standby time 170 hours e Charging time 2 hours e Rechargeable Lithium Polymer battery 120 mAh e Bluetooth 4 1 Bluetooth mono support Headphones Profile HSP Hands Free Profile HFP Bluetooth stereo supported Advanced Audio Distribution Profile A2DP Audio Video Remote Control Profile AVRCP e Supported audio formats SBC and apt X codec Operating range Up to 10 meters 33 feet e Auto power off Note e Specifications are subject to change without notice 8 EN 6 Notice Declaration of conformity Hereby Gibson Innovations declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC You can find the Declaration of Conformity on www onkyo headphones com Disposal of your old product and battery ab Your product is designed a
10. shes alternately 4 Turn on the Bluetooth function of your mobile phone L gt The headset is in pairing mode for 2 minutes D Pair the headset with the mobile phone For detailed information refer to the user manual of your mobile phone NFC pairing 1 Make sure you turn on the NFC function on your phone and your phone s screen remains active 2 Place your phone over the headset so that the NFC detection area of each device can touch each other 3 Pair the headset with the mobile phone For detailed information refer to the user manual of your mobile phone Note e Make sure your mobile phone has the NFC feature available and switched on Make sure your mobile phone is not in standby mode e Pairing with NFC is only suitable for Android mobile operating system 4 2 or above e Refer to the user manual of your mobile phone to identify its NFC detection area The following example shows you how to pair the headset with your mobile phone 1 Activate the Bluetooth feature of your mobile phone select Onkyo E300BT 2 Enter the headset password 0000 4 zeros if prompted For those mobile phones featuring Bluetooth 3 0 or higher no need to enter a password Pile 10 31 Settings Connectivity Settings Bluetooth Devices Found Add Onkyo E300BT Bluetooth device Multiple pairing The headset has a multiple pairing feature which can connect 2 devices sim
11. ultaneously and switch between each other Pair two devices manually 1 Pair your first device see Manual pairing on page 4 2 Press and hold the pairing mute button until the blue and white LED flashes alternately 3 Pair your second device 4 Then you can either e select Onkyo E300BT on the Bluetooth feature of your first device or e switch off the headset and switch it on again L gt The headset is now connected to two devices Pair two devices through NFC 1 Make sure you turn on the NFC function on your phone and your phone s screen remains active 2 Place your phone over the headset so that the NFC detection area of each device can touch each other 3 Pair the headset with the first device 4 Pair the headset with the second device L gt The headset is now connected to two devices Note e When you are listening to music on the first device and play the music on the second device simply pause the music on the first device The headset will be connected to and play music on the second device automatically e When there is an incoming call from one of your devices the music will pause on the other device automatically to receive the call and resume when you finish the call EN 4 Use your headset Connect the headset to a Bluetooth device 1 Turnon your mobile phone Bluetooth device 2 Press and hold the power on off button to turn the headset on L gt The
Download Pdf Manuals
Related Search