Installation Manual - Northern Tool + Equipment
Contents
1. 29 STATUS Ci LEARN RMT Go to control box Press and hold the remote and LEARN RMT buttons simultaneously for 5 seconds or until the alarm sounds Replace control box cover FCC Regulation This device complies with FCC rules Part 15 Operation is subject to the following conditions 1 This device may not cause harmful interference 2 This device must accept an interference that may cause undesired operation Transmitter distance may vary due to circumstances beyond our control NOTE The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment Such modifications could void the user s authority to operate the equipment Connecting Additional Devices Before You Begin Although GTO strongly recommends the use of additional safety devices we do not endorse any specific brand names Only use products that are certified and listed to be in compliance with any applicable UL safety standards Underwriters Laboratories and national and regional safety codes Call GTO Sales at 1 800 543 4283 for information on compatible products for your specific application PLEASE NOTE Contact Sensors Non Contact Sensors and Shadow Loops are not included with the Mighty Mule 500 NOTE Refer to the sensor manufacturer s instructions for information about installing t2. Correct 319V YJLSYW Insert 7 wires into corresponding color terminals Secure wires in terminals IF USING OPTIONAL SOLAR PANEL CHARGER INSTEAD OF TRANSFORMER GO TO PAGE 23 IMPORTANT Do NoT CONNECT BOTH SOLAR PANEL AND TRANSFORMER Transformer Wiring Installation Min 3 Ft Max 1 000 Ft GTO Transformer Mounts Here CAUTION Please call your power company before you dig Failure to do so could cause injury or even death Locate power outlet and identify wire path to control box Dig trench and lay wire from AC power source to control box NOTE If OUTLET is OUTSIDE use weatherproof cover Use only 16 guage multi stranded low voltage PVC sheathed wire RB509 NOTE DO NOT use telephone wire or solid core wire NEVER splice wires together We recommend running wire in PVC conduit 20 Control Box Installation Transformer Wiring Installation se Cut excess cable strip 1 2 off 2 wires twist ends Attach wires to transformer screw terminals SLAdNI yIMOd YMd xnv 4907 sLNdLNO TOULNOD 318V waLSVW AW Feed other end of low voltage wire 10 into box through Insert one wire into each 18VAC terminal Colors do not matter
3. Recommended reinforcement and gate bracket mounting examples Remove clevis pin from the gate bracket and support loose opener 13 Swing gate to CLOSED position check clearance binding by inspecting alignment TIP Turning the pivot bracket over gives more hole alignment options for the post pivot bracket assembly OPEN gate and re attach opener with clevis pin Check for level Secure post pivot bracket to post bracket when clearance is OK Clamp securely Step 5 in both open and closed positions Remove clamps post gate brackets and opener Then use a hammer and center punch to mark hole positions Drill holes completely through gate post and gate cross support Attach post bracket assembly to fence post NOTE Must be through bolted 14 Check for level Adjust post bracket if necessary Remove bolt excess length on post and gate bracket with hacksaw THIS IS THE END OF THE PuLL To Qpen HARDWARE INSTALLATION Skip THE PusH To Open HARDWARE INSTALLATION ON THE NEXT PAGE AND GO TO PAGE 19 To FINISH THE GATE OPENER INSTALLATION PTO Bracket gt Assemble post bracket parts NOTE A Push to Open Bracket Attach opener to gate bracket and secure with hardware re FM148 is required for this type of installation not included quired Reinforcement and Gate Bracket Mounting Steel Pipe Cut in Half a not supplied Gate A Bracket f A Wood or Metal Reinforcement not su
4. Never install any control device where a user will be tempted to reach through the gate to activate the gate opener 2 Be careful with moving parts and avoid close 5 Do not activate your gate opener unless you can proximity to areas where fingers or hands could see it and can determine that its area of travel is be pinched clear of people pets or other obstructions Watch the gate through its entire movement 3 Devices such as contact sensors safety edges and non contact sensors photo beams 6 Secure outdoor or easily accessed gate opener provide additional protection against entrapment controls in order to prohibit unauthorized use of the gate Push To Open Pull To Open Application Application Moving Gate Area Driveway NEVER install any control device within gray area NEVER install any control device within gray area A Important Safety Information A II After Installation p lt W n On Attach the warning signs included to each side of the gate to alert the public of automatic gate operation It is your responsibility to post warning signs on both sides of your gate If any of these signs or warning decals becomes damaged illegible or missing replace them immediately Contact GTO for free replacements The gate is automatic and could move at any time posing serious risk of entrapment No one should be in contact with the gate when it is moving or stationar
5. factory presets shown e 2 DIP Switch 1 Soft Start Stop The soft start stop feature slowly starts the gate as it begins to open or close and slows the gate as it comes to the opened or closed position This saves wear and tear on the gate and gate opener system DIP Switch 2 Warning Buzzer The warning buzzer alerts you when the gate opener is beginning to either open or close the gate It sounds for the first 2 seconds in each direction It also sounds a warning when the gate obstructs two times in one cycle Switching this to OFF only disables the open and close warning not the obstruction warning DIP Switch 3 Push Pull to Open If your gate opens into the property the DIP Switch is set to the OFF position factory setting If your gate opens out from the property the DIP Switch must be set to the ON position NOTE if you have a Push to Open gate application you will need a Push to Open bracket see Push to Open Instructions on page 16 25 DIP 1 ON __ Soft start enabled factory preset OFF Soft start disabled DIP 2 ON __ Buzzer warning enabled factory preset OFF Buzzer warning disabled DIP 3 ON __ Push to open OFF Pull to open factory preset DIP 4 ON __ Slave opens simultaneously with master OFF Slave opens after master factory preset NOTE Not applicable for single gate operator DIP Switch 4 Delay Simultaneous operation If set to ON the slave opens simultaneously with t
6. Cause Injury or Death 1 KEEP CLEAR Gate may move at any time 2 Do not allow children to operate gate or play in gate area 3 This gate is for vehicles only Pedestrians must use separate entrance Logo and warning labels 2 installed on each side of opener housing Technical Specifications Mighty Mule 500 E Z Gate Opener DRIVE e Low friction screw drive linear actuator rated for 5 F to 160 F 20 C to 71 C Use of heater bands on arm and control box will enhance performance in extreme cold temperatures e Powered by a 12 V motor with integral case hardened steel gear reducer Motor speed reduced to 260 rpm Generates 680 ft lb of torque at 12 V e Maximum opening arc of 110 Approximate opening time 90 20 seconds depending on weight of gate POWER e The system is powered by a 12 Vdc 7 0 Ah sealed rechargeable acid battery e Battery charge is maintained by a 120 Vac 18 Vac output transformer rectified to 14 5 Vdc 40 VA through the GTO control board Blade style control board fuse is rated for 15A NOTE The transformer should not be directly connected to any battery Do not replace fuses with higher ampere rated fuses doing so will void your warranty and may damage your control board e OPTIONAL Battery charge is maintained by GTO Solar Panel Charger float voltage of 14 5 Vdc output from a 10 7 8 x 10 1 2 solar panel Generates minimum of 5 W at 300 mA A gated diode on the con
7. link on page 9 farm tube wrought iron wood not recommended for solid surface gates IMPORTANT Check for Proper Gate Installation For the Mighty Mule to work properly gate must be plumb level set in concrete swing freely and not touch the ground and have good working hinges EELE T NEESS S o S o e OR CO SKA KK ia SSS A LXXXI E Z2 XX TX j P Vv aX TOS a Er D Secured Posts in Concrete B Plumb E Centerline Mounting C Free Swinging F Good Working Hinges ball bearing hinges are recommended on gates over 250 pounds Before You Begin Column Installation Information IF THIS OPENER WILL BE USED WITH GATES THAT ARE MOUNTED ON MASONRY BRICK OR ROCK etc COLUMNS READ THE FOLLOWING CAREFULLY BEFORE PROCEEDING A The simplest solution is to install the opener in a push to open configuration requires push to open bracket see accessory catalog The minimum clearance is easier to achieve and clearance is no longer a problem since the opener will be pushing the gate away from the column instead of pull ing it toward the column It is recommended that you place a steel plate between the opener mount ing brackets and masonry surface for additional strength B If a push to open installation is impossible due to traffic hazards terrain etc another
8. not allow children to operate gate or play in gate area This gate is for vehicles only Pedestrians must use a separate entrance A Important Safety Information A These warning labels should be found at the W A RN N G locations specified below If any of them are missing immediately contact GTO for replacements GTO DC SWING SERIES 500 Ih Conforms to UL 325 STANDARDS Maximum Gate 850 Ib 226 7 kg 18 ft 4 8 m c US Voltage 12 Vdc Frequency 0 Hz Power 25 W Class Il Ill and IV Vehicular Swing Gate Operator Serial Number XXXXXXXXXX TO MANUALLY OPEN AND CLOSE THE GATE 1 Turn control box power switch OFF 2 Disconnect front or rear mount from gate bracket 3 Pull opener away from front or rear mount Listeo XXXXXXX Disconnect operator ONLY when the control box power switch is OFF and the gate is NOT moving Moving Gate Can Cause Injury Or Death GTO Inc Tallahassee Florida USA Product identification and manual operation instruction label 1 installed ight hand sid trol box KEEP CLEAR Gate may move at any time a ii Do not allow children to operate gate or play in gate area This gate is for vehicles only Pedestrians must use a separate entrance Warning signs 2 enclosed to be installed on each side of the gate 3 5 feet above the bottom of the gate nae 5 OO E Z GATE OPENER ETETE 1 800 543 GATE 4283 www mightymule com AWARNING D MOVING GATE Can
9. or more contact sensors shall be located at the leading edge bottom edge and post edge both inside and outside of a vehicular swing gate system A hard wired contact sensor shall be located and its wiring arranged so that the communication between the sensor and the gate operator is not subjected to mechanical damage C A wireless contact sensor such as one that transmits radio frequency RF signals to the gate operator for entrapment protection functions shall be located where the transmission of the signals is not obstructed or impeded by building structures natural landscaping or similar obstruction A wireless contact sensor shall function under the intended end use conditions Bottom Edge Contact Sensor on both sides of the gate Post Edge Contact Sensor on both sides of the gate ENTRAPMENT ALARM UL 325 30A 1 1A The Mighty Mule 500 Automatic Gate Operator is designed to stop and reverse within 2 seconds when the gate comes in contact with an obstruction Additionally these operators are equipped with an audio entrapment alarm which will activate if the unit obstructs twice while opening or closing This alarm will sound for a period of 5 minutes or un til the operator receives an intended signal from a hardwired entry exit source e g push button control or keypad and the gate returns to a fully open or fully closed position Turning the power switch on the control box OFF and back ON will also deacti
10. 0 away from an ac power source you will need to use at least one Mighty Mule 5 watt solar panel to trickle charge the battery See the accessory catalog Do not use both transformer and solar If you have thin walled tube or panel gates see Recommended Reinforcement Examples in Quick Reference Guide after Step 3 of Mounting Opener to Gate section Depending on the type of gate a horizontal cross member or mounting plate may be needed to mount the front of the opener and gate bracket to the gate See Gate Bracket Mounting Examples in Quick Reference Guide after Step 3 of Mounting Opener to Gate section Surge protection for transformer Some types of installations require u bolts If the gate is a push to open refer to page 16 in Installation Manual Additional washers or a metal plate may be needed for wooden post Outlet in weatherproof cover Strain relief nuts for accessory devices If post is more than 6 bolts longer than 8 are needed With Gate in OPEN position using clamps secure opener to gate post and center cross member of gate Attach opener to gate bracket and secure with required hardware Steel Pipe Cut in Half not supplied Wood or Metal Reinforcement not supplied FRONT VIEW SIDE VIEW Mounting Plate Created for 1 Decorative Gate 4 required but not i supplied i yt d i d Remove excess bolt I ngth with hacksaw or bolt cutters i 1 1
11. GTO Inc GTO unless otherwise indicated All rights are reserved by GTO and content may not be reproduced downloaded disseminated published or transferred in any form or by any means except with the prior written permission of GTO Any reprinting of GTO publications is by permission only Copyright infringement is a violation of federal law Mighty Mule E Z Gate GTO are registered trademarks of GTO Inc America s DIY Automatic Gate Openers is a trademark of GTO Inc and are the exclusive property of GTO Inc GTO All rights are reserved by GTO and these marks may not be used in any for without the prior written permission of GTO 39 Men ype MULE LY 46 E Z GATE OPENERS For sales call toll free 1 800 543 GATE 4283 The GTO Inc Sales Department is open Monday Friday 8 00 A M 5 00 P M Eastern Time For technical service Call toll free 1 800 543 1236 The GTO Inc Technical Service Department is open Monday Friday 8 00 A M 7 00 P M Eastern Time FING GATES THAT OPEN 3121 Hartsfield Road Tallahassee Florida USA 32303 Telephone GTO Sales 1 800 543 GATE 4283 or 850 575 0176 Fax 850 575 8912 or GTO Technical Service 1 800 543 1236 or 850 575 4144 Fax 850 575 8950 www mightymule com
12. Q merh 500 o E Z GATE OPENER SUE RIAKI A LLY AOL Ate ORR NNS AEE SRS ATL O UN D n o U OO i HED TL BASEE SESSO Ss PELL H ESSESI ee SON SSS a P vee LTD fi QA OK DM UD Bi SR SOAK S SX SS gt INAN SN unin Oy NN SX Se ay ly REA he ILA ASS A Y BSS LIZA SSS EAS RSS L eRe 2 e OLON UE gl S OAA A AA SESSE 5 Easy installation Steps 1 Watch the Installation DVD and Read the Safety Information Technical Specifications and the Before You Begin sections in the manual 2 Install the Gate Opener and Control Box 3 Power the system using the AC Transformer or optional Solar Panel Charger Kit 4 Programming and customizing the system to your individual settings 5 Adding additional safety devices and access controls as A Warning A This equipment is similar to other gate or door equipment and meets or exceeds Underwriters Laboratory Standard 325 UL 325 However gate equipment has hazards associated with its use and therefore by installing this product the installer and user accept full responsibility for following and noting the installation and safety instructions Failure to follow installation and safety instructions can result in hazards developing due to improper assembly You agree to properly install this product and that if you fail to do so GTO Inc shall in no event be liable for direct indirect incidental special or consequential damag
13. Setting Obstruction Stall Force and Auto Close Time Setting Your Personal Code CONNECTING ADDITIONAL DEVICES Input Connections 10 10 10 10 11 11 12 12 13 13 16 19 19 20 22 22 23 25 25 26 26 27 27 28 28 30 31 Connecting Accessories Connecting GTO Automatic Lock Connecting Other Auxilary Devices 32 32 33 MAINTENANCE amp TROUBLESHOOTING Maintenance Tips 33 33 Troubleshooting Guide 34 Please Read This First Thank you for purchasing a Mighty Mule E Z Gate Opener GTO s do it yourself automatic gate opener When correctly installed and properly used your Mighty Mule E Z Gate Opener will give you many years of reliable service Please read the following information and watch the enclosed video to ensure you have the correct system for your particular needs Furthermore this manual and the DVD will enable you to properly install your Mighty Mule E Z Gate Opener The Mighty Mule E Z Gate Opener is designed for installation on a pull to open single leaf gate gates that open into the property By purchasing an accessory bracket the Mighty Mule E Z Gate Opener can accommodate a push to open single leaf gate gates that open out from the property The gate must not exceed 18 feet in length and weigh more than 350 pounds or exceed 8 feet in length and weigh more than 850 pounds please see Technical Specifications on page 9 The M
14. Substitute a Pin Lock for the clevis pin on the front mount of the gate opener to prevent unauthorized removal of the opener from the gate see accessory pages in back of this book A Important Safety Information A WARNING To reduce the risk of injury or death 1 pa W READ AND FOLLOW ALL INSTRUCTIONS Failure to meet the requirements set forth in the instruction manual could cause severe injury and or death for which the manufacturer cannot be held responsible When designing a system that will be entered from a highway or main thoroughfare make sure the system is placed far enough from the road to prevent traffic congestion The gate must be installed in a location that provides adequate clearance between it and adjacent structures when opening and closing to reduce the risk of entrapment Swinging gates must not open into public access areas The gate and gate opener installation must comply with any applicable local codes I Before Installation 1 Verify this opener is proper for the type and size of gate its frequency of use and proper class rating Entrapment Zones for a Pull To Open Application Gate in the Open Position Driveway 2 W n nN Make sure the gate has been properly installed and swings freely in both directions Repair or replace all worn or damaged gate hardware prior to installation A freely moving gate will require less force to operate and will enh
15. T button for 5 Press button on opener remote to fully close gate Open limit is seconds or until the alrm sounds set upon reaching the fully closed limit Test and if needed reset NOTE If your gate obstructs before it fully closes you may and start over need to increase the stall force See page 28 Resetting Open Gate Limit gt Press button on opener remote to close gate Hold the LEARN MASTER LIMIT button for 10 seconds or until the alarm sounds to clear Go back to setting open gate 27 limit step 1 at the top of this page Control Box Settings Setting Obstruction Stall Force amp Auto Close Time 33404 TIVLS a Turn the STALL FORCE arrow in the center of the potentiom Turn the AUTO CLOSE TIME arrow in the center of the potenti eter with small flat head screwdriver Adjust the sensitivity from the ometer with small flat head screwdriver Turning the pot all the way MINIMUM position up to the point where the gate operates without counter clockwise will turn the auto close feature off The minimum obstructing from its own weight or the wind conditions in your area auto close time is 3 seconds The maximum turn the pot all the way clockwise auto close time is 120 seconds IMPORTANT For safety reasons the obstructions setting or Stall Force on the Mighty Mule control board comes f
16. X OEO N S S Jl PSSM OAA LAS cS amp A gt gt A K KSSS P SRNA SY LDS SQ gprs BSS SRS ot lel D gt SS Qe Fa ESSES N IKROS DAR DARD NNSS aS ya N Vor EAN Se S I a S NX U N Secure post pivot bracket to post bracket when clearance is OK Step 5 in both open and closed positions SSSR OR XS PKL OOS ORR S MISS SRS ds BOS Sy SS SHEE SSIS ESTES LSE ESSES X x Remove clamps post gate brackets and opener Then use a hammer and center punch to mark hole positions Attach post bracket assembly to fence post NOTE Must be through bolted Control Box Installation Control Box Installation TOOR AL AT A OA a AR MO Vat alae Lae is a oak MD CAL lp MONO NOM Locate control box mounting area IMPORTANT Be sure to mount box at least 3ft from AC power and 3ft off the ground Position battery in control box as shown Connect battery leads from control board to battery IMPORTANT Red wire to Red Post positive and black wire to Black Post negative xA NY Twist each end of the gate opener power cable s 7 colored wires Feed cable 6 into box Tighten strain relief nut to secure cable Feed cable through strain relief nut Control Box Installation Control Box Installation
17. ance the performance of the opener and safety devices used with the system see page 10 Review the operation of the system to become familiar with its safety features Understand how to disconnect the opener for manual gate operations see page 2 This gate opener is intended for vehicular gates ONLY A seperate entrance or gate must be installed for pedestrian use see page 7 Always keep people and objects away from the gate and its area of travel NO ONE SHOULD CROSS THE PATH OF A MOVING GATE Pay close attention to the diagram below and be aware of these areas at all times Gate in the Open Position Entrapment Zones for a Push To Open Application Driveway A Important Safety Information A Entrapment Zones for a proper Pull To Open installation Zone leading edge of the gate and the fence post Zone 2 between the gate and the gate post Zone 3 the path of the gate Zone 4 the space between the gate in the open position and any object such as a wall fence tree etc Zone 5 pinch points between the opener and gate Il During Installation 4 If push buttons or key switches are installed they should be within sight of the gate yet located at 1 Install the gate opener on the inside of the prop erty and fence line DO NOT install an opener on the outside of the gate where the public has access to it least 10 feet from any moving part of the gate see diagram below
18. arnings for the consumer Because there are many possible applications of the gate opener the safety precautions and warnings contained in this manual cannot be completely exhaustive in nature They do however provide an overview of the safe design installation and use of this product CAREFULLY READ AND FOLLOW ALL SAFETY PRECAUTIONS WARNINGS AND INSTALLATION INSTRUCTIONS TO ENSURE THE SAFE SYSTEM DESIGN INSTALLATION AND USE OF THIS PRODUCT Precautions and warnings in this manual are identified with this warning symbol The symbol identifies conditions that can result in damage to the opener or its components serious injury or death Because GTO automatic gate openers are only part of the total gate operating system it is the responsibility of the consumer to ensure that the total system is safe for its intended use Manually Opening and Closing Gate A CAUTION The gate will move freely and uncontrolled when the gate opener is removed from the gate ONLY disconnect the opener when the control box power switch is OFF and the gate is NOT moving Disconnecting the Opener 1 Turn control box power switch OFF 2 Remove hairpin clip clevis pin and bushing from either the front or rear mounting point 3 Remove the opener from the mount The gate can be opened and closed manually when the opener is disconnected Front Mount J Clevis Pin oh Gate Bracket 2n Bushing Hairpin cip 7 NOTE
19. e systems with a maximum of 30 watts A second battery 7 amp tractor auto or deep cycle marine battery is recommended for solar and or high traffic applications if needed Consult Solar Panel Installation Instructions for further information The solar panel must be positioned facing the path of the sun Feed wire from solar panel through hole in knockout in and in an open area away from shade It should receive at least 8 control box hours of direct sunlight for a full charge IMPORTANT Mount the panel using IMPORTANT Requires 8 hours the curved pipe provided to maintain the proper angle to the sun of direct sunlight a day 23 SLAdNI 4aMOd AY YMd xny 43071 SLNdLNO TOYLNOD Insert RED wire into SOLAR positive terminal and Feed cable 10 into box BLACK wire into SOLAR negative terminal Wrong Secure with terminal screws NOTE All connections should be Solar Panels connect in PARALLEL weatherproofed using weatherproof splice kits available at hardware and electrical supply stores attach BLACK to negative solar terminal on control board attach RED to positive solar terminal on control board 24 Control Box Settings IMPORTANT Before making any changes to dip switches turn control box off
20. eam or any other accessory wired to this 6 blink Shorted terminal Try the remote If the remote works the problem is the accessory RF yellow Flickers Receiving 318 MHz Normal operation when remote or wireless keypad is used RF RF yellow OFF No 318 MHz RF Battery in Remote Received Program Remote Antenna Receiver Connections Antenna Receiver Power green OFF No AC or Solar Transformer Power e Breaker or GFI e Power at AC outlet e Output of Transformer e Voltage on wire at 18 VAC Input Solar e Solar Panel Wires Reversed Weather Solar Panel Placement Output of Solar Panel Voltage on wire at Solar Input Charge red ON Fast Charging Mode Battery Voltage should be 14 8 VDC when connected to the circuit board Charge red Fast Soak Charging Mode Battery Voltage should be 14 1 VDC when connected to the circuit board Blinking Charge red Slow Float Charge Battery Voltage should be 13 8 VDC when connected to the circuit board Blinking Charge red OFF Battery Not Being e AC power Charged e Transformer e Solar Panel e Charging Circuit 35 Repair Service If your Mighty Mule Gate Opener is not operating properly please follow the steps below 1 First use the procedures found in the Maintenance 3 If repair or replacement of your gate opener is amp Troubleshooting Guide see page 33 necessary the Service Department will assign a Return Goods Authorization RGA number to 2 If you are unable to sol
21. ed when the gate is at the fully open position At any other position activation of this input has no effect on gate operation e Activation of this input while gate at the fully open position will prevent gate from closing 6 CLOSE EDGE Typically for use with safety edge device e Activation of this input while the gate is closing will cause the gate to stop and reverse direction for approximately 2 seconds e Activation of this input while the gate is opening has no effect gate will continue to open e Activation of this input while gate is idle will prevent gate from closing OPEN EDGE Typically for use with safety edge device e Activation of this input while the gate is opening will cause the gate to stop and reverse direction for approximately 2 seconds e Activation of this input while the gate is closing has no effect gate will continue to close e Activation of this input while gate is idle will prevent gate from opening 31 Connecting Additional Devices 000008 Fi MASTER CABLE CONTROL INPUTS According to Application According to Application GTO Loop Detector GTO Photo Beams Mighty Mule Push Button Control Mighty Mule Vehicle Sensor Refer to Vehicle Sensor manual for additional connections Mighty Mule Keypad NOTE Connections are for typical applications There may be additional connection option
22. es or loss of profits whether based in contract tort or any other legal theory during the course of the warranty or at any time thereafter The installer and or user agree to assume responsibility for all liability and use of this product releasing GTO Inc from any and all liability If you are not in agreement with this disclaimer or do not feel capable of properly following all installation and safety instructions you may return this product for full replacement value READ ALL INSTRUCTIONS CAREFULLY AND COMPLETELY before attempting to install and use this automatic gate opener This gate opener produces a high level of force Stay clear of the unit while it is operating and exercise caution at all times All automatic gate openers are intended for use on vehicular gates only The Mighty Mule Gate Opener is intended for use with vehicular swing gates The opener can be used in Class I Class II Class III and Class IV Vehicular Gate Opener Class Categories Residential Vehicular Gate Opener Class I A vehicular gate opener or system intended for use in a home of one to four single family dwelling or a garage or parking area associated therewith Commercial General Access Vehicular Gate Opener Class II A vehicular gate opener or system intended for use in a commercial location or building such as a multifamily housing unit five or more single family units hotel garages retail store or other building servicing the
23. general public Industrial Limited Access Vehicular Gate Opener Class III A vehicular gate opener or system intended for use in an industrial location or building such as a factory or loading dock area or other locations not intended to service the general public Restricted Access Vehicular Gate Opener Class IV A vehicular gate opener or system intended for use in a guarded industrial location or building such as an airport security area or other restricted access locations not servicing the general public in which unauthorized access is prevented via supervision by security personnel Table of Contents PLEASE READ THIS FIRST IMPORTANT SAFETY INFORMATION TECHNICAL SPECIFICATIONS BEFORE YOU BEGIN Check Direction of Gate Swing Check Existing Gate Size and Material Check for Proper Gate Installation Column Installation Information Items Included Tools Needed Items Not Included GATE OPENER INSTALLATION Mounting Pull to Open Opener to Gate Mounting Push to Open Opener to Gate CONTROL BOX INSTALLATION Control Box Installation Transformer Wiring Installation Receiver Installation Gate Stop Installation SOLAR PANEL INSTALLATION CONTROL BOX SETTINGS DIP Switches Setting Pull to Open Closed Gate Limit Resetting Closed Gate Limit Setting Push to Open Open Gate Limit Resetting Open Gate Limit
24. grams kg Converting Temperature deg Celsius C x 1 8 32 deg Fahrenheit deg Fahrenheit F 32 1 8 deg Celsius For Your Records Please record the product serial number located on the right hand side of the control box and the date and place of purchase in the spaces provided below Refer to this information when calling GTO for service or assistance with your automatic gate opener Serial Number Date of Purchase Place of Purchase Remember to keep all receipts for proof of purchase 37 UT EUL aw 4 E Z GATE OPENERS Accessories are Available From Your Retail Store Solar Panel FM121 The Solar Panel is a 5 watt solar powered battery charger for use with the FM500 amp FMS502 gate operator systems Particularly suited for remote installations each Solar Panel comes with tubular steel support mounting clips wire connectors and 8 ft of low voltage wire see Low Voltage Wire for additional wire The Mighty Mule control board has clearly labeled terminal connections for easy installation of the Solar Panel Installation in some regions of the world will require multiple solar panels for adequate charging power Dual gates require a minimum of 10 watts of solar charging power 10 watt solar panels are available Push Button Control FM132 Unlit doorbell button for remote entry or exit control Wires directly to the control board and uses 16 gauge multi stranded dual conductor low voltage wire sold separa
25. he master If set to OFF the slave opens after the master NOTE Not applicable for single gate operator Control Box Settings to Open Closed Gate Lim to open go to pg 16 Press button on opener remote gate should start closing Press button on opener remote again when gate is in desired CLOSED position Press button on opener remote to fully open gate Closed limit is or until the alarm sounds set upon reaching fully open position Test and if needed reset NOTE If your gate obstructs before it fully closes you may and start over need to increase the stall force See page 28 LEARN IMAST LIMIT TA i lt Press and hold the LEARN MAST LIMIT button for 10 seconds or until the alarm sounds to clear Go back to the setting closed limit steps on the top of this page Press button on opener remote to open gate 26 Control Box Settings a in CLOSED position turn control box power switch Press button on opener remote gate should start opening Press but ton on opener remote again when gate is in desired OPEN position Press and hold the LEARN MASTER LIMI
26. he 16 gauge multi stranded dual conductor Low Voltage Wire is for connecting the AC powered transformer or the Solar Panel to the control board Also used for the connection of accessories such as locks keypads push buttons and other wired control devices This specially designed wire is UV treated PVC coated and ready for direct burial Available in 1000 rolls or special lengths Push to Open Bracket FM148 Required when Mighty Mule 500 502 gate operator s must push the gate open such as on a sloping driveway or where space prevents gate s from opening inward pulled open Order two PTO brackets for conversion of a dual swing gate installation Column Mount Lock Receiver 433IH For mounting the Automatic Gate Lock on brick columns walls or for other applications with limited space between gate and post Replacement Transformer RB570 Standard 18 volt 2200 mA AC transformer for maintaining the battery included with the Mighty Mule gate operator This is the only transformer approved for use with all UL325 Mighty Mule gate operator systems Garage Door Receiver RB709U The Garage Door Receiver allows you to use the same Mighty Mule entry transmitter to operate your gate operator and your garage door operator Compatible with most garage door operators If you have a question about any special order item just call 1 800 543 GATE The contents of all material available on this installation manual are copyrighted by
27. hese devices on a vehicular gate The Mighty Mule 500 will ONLY accept accessory devices with normally open dry contact output 30 Connecting Additional Devices NOTE e All control inputs are dry contact normally open inputs DO NOT apply external voltage sources to these inputs e All inputs are connected with respect to COMMON terminal e The status light will blink once when its corresponding input is activated C COM Circuit common reference for all logic input e Two 2 terminals to provide extra common connection point CYCLE Typically for use with doorbell button or hardwired key pad e Each activation at this input will cycle the operation as follows OPEN STOP CLOSE STOP OPEN G 3 SAFETY Typically for use with photo beam device loop detector or other non contact sensors e Activation of this input while the gate is closing will cause the gate to stop and return to the opened position e Activation of this input while the gate is opening has no effect gate will continue to open e Activation of this input while gate is idle will prevent gate from closing 5 4 EXIT Typically for use with exit loop or wand e Activation of this input will open the gate if it s not already at the open position e Activation of this input while at open limit will restart the auto close time if enabled s SHADOW Typically for use with loop detector device e This input is only monitor
28. ighty Mule E Z Gate Opener can be used on vinyl aluminum chain link farm tube and wrought iron gates Use on solid wood gates is not recommended Solid surface gates have a high resistance to the wind If the wind is strong enough the opener will obstruct and stop The Mighty Mule E Z Gate Opener accommodates extra transmitters digital keypads solar panels push buttons automatic gate locks and other access control products These optional accessories see the enclosed Mighty Mule Accessory Catalog are available at most stores Your store should be able to special order any accessory not in stock If your store cannot special order accessories please call the GTO Sales Department 800 543 GATE The Mighty Mule E Z Gate Opener features adjustable obstruction sensing This safety feature makes the gate stop and reverse direction within 2 seconds when it comes in contact with an obstruction MIN is the factory setting meaning the gate will exert the minimum force on an obstruction before it stops and reverses direction The Mighty Mule E Z Gate Opener also has an adjustable auto close feature After the gate reaches the fully open position it can be set to remain open up to 120 seconds before automatically closing Pressing the transmitter button at any time after the gate opens fully will cause it to close immediately OFF is the factory setting meaning the gate will stay open until you press the transmitter or
29. ith a transformer Actual cycles may vary slightly depending upon the type and condition of gate and installation Mighty Mule 500 Gate Capacity Cycle Chart Estimated number of daily cycles based on use with a transformer and one 1 12 Volt battery Number of Cycles Per Day 850 Ibs 135 125 NR NR NR NR NR 750 Ibs 145 135 125 NR NR NR NR 650 Ibs 155 145 135 125 NR NR NR 550 Ibs 165 155 145 135 NR NR 450 Ibs 175 165 155 145 NR 350 Ibs 185 175 165 155 250 Ibs 195 185 175 165 150 Ibs 205 195 185 175 100 Ibs 215 205 195 185 50 Ibs 225 205 195 5 6 10 12 Gate Length NOTE Ball bearing hinges should be used on all gates weighing over 250 lb a a D v 2 To determine the number of cycles the gate operator will perform using solar panels please see the specifications listed on page 23 or call 800 543 1236 or 850 575 4144 for more information An operation cycle is one full opening and closing of the gate These specifications are subject to change without notice Before You Begin Check Direction of Gate Swing Requires Push To Open Bracket FM148 NOT INCLUDED Your Property Your Property Pull to Open Option Push to Open Option Instructions begin on Instructions begin on page 13 page 16 Check Existing Gate Size and Material e Gate size Up to 18 feet or up to 850 Ibs See chart Type of gate material Vinyl aluminum chain
30. keypad etc again PLEASE NOTE TIf your application requires any of the following e Swing gates longer than 18 feet or weighing more than 850 pounds e Slide gates e Heavy duty or commercial uses e Professional installation Go to gtoinc com for a dealer or retailer near you or call GTO at 800 543 GATE 4283 or 850 575 0176 for information about our GTO PRO professional line of gate openers and accessories Our Sales Department will be glad to give you the name and phone number of a GTO PRO dealer near you BEFORE YOU BEGIN TO INSTALL YOUR AUTOMATIC GATE OPENER watch the enclosed video and read these instructions carefully and completely to become familiar with all parts and installation steps The video is only designed as an overview of the installation procedure You must read the installation manual for detailed instructions on gate opener safety and proper use of the gate opener MIGHTY MULE ie K E Z GATE OPENERS A Important Safety Information A Because automatic gate openers produce high levels of force consumers need to know the potential hazards associated with improperly designed installed and maintained automated gate opener systems Keep in mind that the gate opener is just one component of the total gate operating system Each component must work in unison to provide the consumer with convenience security and safety This manual contains various safety precautions and w
31. ng Sensor is designed for residential and agricultural applications and is compatible with most Mighty Mule automatic gate opener models see Sensor Box for model compatibility The Sensor is an electromagnetic sensor which offers hands free operation of the Mighty Mule Gate Operator with a 12 ft radius of detection of vehicles in motion Automatic Gate Lock Pull to Open FM143 A MUST for added security Solenoid driven with a steel housing Unlocks and locks automatically as gates open and close Used with Mighty Mule DC swing gate operating systems for maximum stability and security Comes with a keyed manual release Recommended for gates over 8 ft long Ideal for animal enclosures or high wind areas 38 Accessories are Available From Your Retail Store con t Wireless Entry Intercom Keypad FM136 Allows owner to screen guest at the gate before allowing access to the property Keypad also allows owner to give up to 25 programmable entry codes to family friends or approved delivery personnel Codes can be permanent of temporary Up to 500 feet reception Additional base stations available F3101MBC Replacement Battery FM150 Standard 12 volt 7 0 amp hour maintenance free battery for the Mighty Mule FM500 amp FM502 gate operator systems This is the only battery approved for use with the Mighty Mule FM500 amp FM502 gate operator systems Life expectancy is 2 3 years Low Voltage Wire RB509 T
32. option is to re hang the gate You may hang it on a post either in the center of the column or at the back corner or move the gate to the back corner of the columns C The most difficult solution is to cut a notch in the column to accommodate the opener and power cable This job is NOT for the inexperienced eA Column Mount Example Pivot Bracket gt B A B can not exceed 14 inches rr F Example If A is 2 then B can not exceed 12 Column Or Hinge Gate Receiver and Control Box Post Pivot Bracket 8 Nylon Cable Tie 14 3 8 Bushing 2 Ss Position Bracket 5 16 Lock Washer 1 5 16 Washer 1 Do P pan gt O 3 8 x 8 Bolt 4 3 8 x 3 Bolt 2 Demm 3 8 x 2 Bolt 1 5 16 x 1 3 4 Bolt 1 W o gt 2 Mounting Screw 5 Hairpin Clip 2 poa po 3 8 x 1 1 4 Clevis Pin 2 3 8 Washer 9 ae 5 16 Nut 1 3 8 Lock Washer 7 3 8 Nut 7 Before You Begin Tools Needed 5 16 Bit Pliers 9 16 ili wo Head gt Pen 1 2 wrench Flat Head Screwdriver Flat Head Measure Low voltage wire will be needed to run from the transformer to the control box length depends upon the distance between the transformer power supply and the control box See Transformer Wiring Installation on page 20 and the accessory catalog PVC conduit If your gate is more than 100
33. oss each terminal Connections to Slave Inputs Slave Arm Power Cable Slave Input ORG amp GRN BRN amp GRN voltage with wires disconnected 11 VDC each across each terminal Connections to Master Inputs Master Arm Power Cable Rev Counter Connections to Master Inputs Master Arm Power Cable Rev Counter Visual Feedback Symptom Diagnosis Status clear Cycle Terminal Disconnect the push button keypad intercom keypad or any other 1 blink Shorted accessory wired to this terminal Try the remote If the remote works then the problem is the accessory Status clear Safety Terminal Disconnect the loop detector photo beam or any other accessory wired 2 blinks Shorted to this terminal Try the remote If the remote works the problem is the accessory Status clear Exit Terminal Disconnect exit wand loop detector photo beam Knox box or any other 3 blinks Shorted accessory wired to this terminal Try remote If the remote works the problem is the accessory Status clear Shadow Terminal Disconnect the loop detector photo beam or any other accessory wired to 4 blinks Shorted this terminal Try remote If the remote works the problem is the accessory Status clear Close Edge Terminal Disconnect the edge sensor photo beam or any other accessory wired to this 5 blinks Shorted terminal Try the remote If the remote works the problem is the accessory Status clear Open Edge Terminal Disconnect edge sensor photo b
34. pplied FRONT VIEW SIDE VIEW Mounting Plate Created for 1 Decorative Gate 4 A required but not j gt Gate supplied N Bracket io a ment 1 i Remove excess bolt length with hacksaw or bolt cutters With gate in CLOSED position using clamps secure opener to Recommended reinforcement and gate bracket mounting gate post and center cross member of gate examples 2 minimum pinch point clearance Swing gate to OPENED position Check clearance binding by inspecting the alignment Secure post pivot bracket to post bracket when clearance is OK in both open and closed positions TIP Turning the pivot bracket over gives more hole alignment options for the post pivot bracket assembly Remove clevis pin from the gate bracket and support loose opener 16 RNS mae OS lt S RR YO SSS S CLOSE gate and re attach opener with clevis pin Check for level Clamp securely RX XA AY xX RRS RN ESS E ESS SERS XK AJ Al gt KX Rrr TSS RRN PNK SSR SRS TEES PRS NY Mark middle of post bracket slots on fence post Mark middle of gate bracket slots on gate cross support EENS SER PESASSE IESS RSS ROSSAS ESSES SESS NSA SONS b S AIA XO oe 5 PD gt or SOAS S I Ce ESTASS AS Cong DOS SS SASS Drill holes completely through gate post and gate cross support al PRG PARRY TREN
35. pray to the front and control board rear mounts to minimize this effect 33 Troubleshooting Guide If your gate opener does not function properly after it is installed use this guide before calling the GTO Service Department Audible Feedback Symptom 1 short beep upon activation 1 short beep upon power up Continuous Uninterrupted Alarm 1 beep with 10 seconds off 1 beep then 2 beeps 1 beep then 3 beeps 1 beep with 2 seconds off 2 beeps with 2 seconds off 3 beeps with 2 seconds off 4 beeps with 2 seconds off Diagnosis Blown Fuse Low or Bad Battery Loose Battery Connection Circuit Board Powered Up amp Ready Circuit Board Senses an Obstruction Low Battery Condition Master Motor Terminals Shorted Slave Motor Terminals Shorted Master Arm Limit Switch Error Slave Arm Limit Switch Error Master Arm Rev Counter Error Slave Arm Rev Counter Error 34 Fuse Battery Under Load Battery Harness Connections Normal Operation Path of Gate Gate for Level and Plumb Stall Force Adjustment Disconnect Safety Devices Rev Counter Fuses Battery Harness Connections Battery Under Load Connections to Master Inputs Master Arm Power Cable Motor Circuit Board Connections to Master Inputs Master Arm Power Cable Motor Circuit Board Connections to Master Inputs Master Arm Power Cable Master Input ORG amp GRN BRN amp GRN voltage with wires disconnected 11VDC acr
36. ption in mounted position OK secure Receiver in position to fence or post NOTE If mounting on metal fence mount receiver on a piece of wood Mounting the receiver on metal can cause intereference and the receiver may not work properly DO NOT mount upside down Gate Stop Installation Br gt lt lt S SA 6 DY N P A NY amp S i A Fully open gate Attach gate stop with one of the following Position gate stop with gate CLOSED to fence post Tighten e U bolts tube and chain link gates Not included fasteners Cut off excess bolt length e Wood lag screws flat aluminum wood supports Not included Do not tighten Solar Panel Installation Optional maximum number of gate cycles to 12 v single gate 5 watts solar charger 4 8 expect per day in a particular area 13 12 v single gate 10 watts solar charger 8 16 26 when using from 5 to 30 watts of 12 v single gate 15 watts solar charger 11 20 30 solar charging power see accessory 12 v single gate 20 watts solar charger 14 28 38 46 54 pages in back of this book The 12 v single gate 25 watts solar charger 17 36 figures shown are for winter 12 v single gate 30 watts solar charger 20 44 minimum sunlight and do not account for the use of any accessory items Accessories connected to your system will draw additional power from the battery NOTE A minimum of 5 watts of solar charging power is required for Mighty Mule 500 single gat
37. rom the factory set at MIN minimum In many installations this setting will need to be adjusted to overcome the weight and size of the gates ALWAYS KEEP SAFETY AT THE TOP OF YOUR LIST WHEN ADJUSTING OR SERVICING YOUR AUTOMATIC GATE OPENER Setting Personal Transmitter Code All GTO transmitters are set to a standard code at the factory and are ready to operate your GTO PRO Gate Opener For your safety and security however we strongly recommend that you replace the factory setting with your own personal code Follow the directions below Remove back cover of the opener remote Flip opener remote over Use small screwdriver to move switch es to random positions If you have more than one transmitter now is a good time to set them all with the same code 28 Control Box Settings Setting Personal Transmitter Code STATUS OE LEARN RMT Release the remote button then release the LEARN RMT button The new code is now programmed Fill in boxes below with your transmiter code for your records Example 123 45 67 8 9
38. s for applications that are not illustrated here 32 Connecting Additional Devices Connecting GTO Automatic Lock CONTROL OUTPUTS POWER LOCK AUX INPUTS PWR RLY GTO 18VOLT TRANSFORMER OR SOLAR Wire from Automatic GTO Lock GTO Lock GTO Lock Connection For use exclusively with GTO Lock FM143 or FM144 Connect the red and black leads from the lock to the GTO LOCK Connecting other devices to these terminals may cause incorrect terminal on the GTO PRO 2000XL control board operation and void your warranty You do not use the lock board with this control board Connecting Other Auxiliary Devices mag Locks Sirens Lights e These 2 terminals are normally open dry contact no voltage relay ouput e These 2 terminals are ON shorted whenever the gate is moving and OFF opened otherwise e These 2 terminals maximum rating is 24Vdc 1 Amp Maintenance amp Troubleshooting Maintenance Tips e On all gates weighing 250 Ib or more routinely e Clean the push pull tube with a soft dry cloth and grease the ball bearing hinges at least 4 times a year apply silicone spray to it at least once per month more frequently if the gates are near a coastal area e While oxidation is a normal part of weathering e Keeping a few mothballs in the control box will of equipment that is exposed to the elements we discourage insects from entering it and damaging the recommend you apply silicone s
39. safety instructions Make sure everyone who is using or will be around the gate and gate operator are aware of the dangers associated with automated gates In the event you sell the property with the gate operator or sell the gate operator provide a copy of these safety instructions to the new owner Should you lose or misplace this manual a copy can be obtained by downloading one from the Mighty Mule web site www mighty mule com by contacting GTO Inc at 3121 Hartsfield Road Tallahassee Florida 32303 or by calling 1 800 543 4283 and requesting a duplicate copy One will be provided to you for a nominal fee A Important Safety Information A As specified by Gate Operator Safety Standard UL 325 30A 1 1 automatic gate operators shall have an inherent entrapment sensing system and shall have provisions for or be supplied with at least one independent secondary means to protect against entrapment The Mighty Mule 500 utilizes Type A an inherent i e built in entrapment sensing system as the primary type of entrapment protection Also the Mighty Mule 500 has provisions for the connec tion of Type B2 protection to be used as the secondary type of entrapment protection and is recommended 1 For gate operators utilizing a contact sensor e g safety edge sensor Type B2 in accordance with UL 325 51 8 4 i Leading Edge Contact Sensor on both sides of the gate Se a ee VehicularGate A One
40. tely Pin Lock FM133 The Pin Lock substitutes for the clevis pin at the front end of the Mighty Mule gate openers Helps prevent theft of the operator from the gate while allowing quick release of the operator Key Chain Two Button Transmitter FM134 The Key Chain Mini Transmitter is a miniature version of the Mighty Mule entry transmitter and has the same adjustable code settings battery is included Single Button Transmitter FM135 The Mighty Mule entry transmitter with adjustable code settings is standard equipment with all Mighty Mule systems battery is included Digital Keypad FM137 The specially designed digital keypad can be easily installed as a wireless or wired keypad It can be programmed to use up to 25 different personal identification number PIN codes Each code is face programmable with additional security features built in Wired installations require 16 gauge low voltage multi stranded dual conductor direct burial wire sold separately Requires 3 AA batteries not included Mounting Post FM100 In Ground This black powder coated pedestal is designed to provide convenient access to your keypad wireless intercom or other access control device from your vehicle With its break down design it is easy to install and works well in most standard applications Surface Mount Flanges F102 and Extensions F103 for added height are available Mighty Mule Vehicle Sensor FM138 The Gate Openi
41. the hole SiNdLno JTOYULNOD of 2 pj S v4 8 v4 B Secure with terminal screws Plug in transformer to power outlet Use of a surge protector is highly recommended If outdoors use weatherproof box 21 Control Box Installation Receiver Installation FCC Regulation This device complies with FCC rules Part 15 Operation is subject to the following conditions 1 This device may not cause harmful interference 2 This device must accept an interference that may cause undesired operation Transmitter distance may vary due to circumstances beyond our control NOTE The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment Such modifications could void the user s authority to operate the equipment Install Receiver within 10 ft of control box longer lengths avail able call us NOTE NEVER splice receiver cable DO NOT run cable through metal conduit because the receiver signal range will decrease DO NOT run cable through conduit contain ing AC wire DO NOT place receiver within 3 feet of AC power e Tips 1 Mount the receiver high and above any obstructions fence pickets column caps etc 2 If radio control seems limited try moving the receiver 1 2 feet in each direction to reduce radio noise dead spots Check Receiver Remote signal rece
42. trol board prevents battery discharge NOTE NR indicates this size and weight combination is not recommended for the Mighty Mule 500 CONTROL e GTO microprocessor based control board is set for single leaf pull to open gate installations DIP switches can be adjusted to accommodate an optional kit for push to open gates see Accessory Catalog e Control board has temperature compensated circuits e A circuit on the control board regulates charging Sleep draw is 25 mA active draw is 2 to5 A e Auto memorization of digital transmitter code e GTO remote mounted RF receiver tuned to 318 MHz e Operator length with push pull tube fully retracted is 40 1 4 mounting point to mounting point Max stroke 22 e Adjustable auto close timer 15 to 120 s and obstruction sensitivity e Power terminal block accommodates a transformer or solar panels NOTE Do not use solar panel and transformer at the same time e DIP switches simplify setup of gate operator e Accessory terminal block fully compatible with push button controls digital keypads safety loops etc e Control board allows connection of safety edge sensors and photoelectric sensors e Audio entrapment alarm sounds if unit encounters an obstruction twice while opening or closing OPERATIONAL CAPACITY e The Gate Capacity Chart shows approximate cycles per day you can expect from the Mighty Mule 500 Automat ic Gate Operator when powered w
43. vate the alarm Wireless controls such as transmitters and wireless keypads will not deactivate the alarm A Important Safety Information A Required Safety Precautions for Gates Install Warning Signs Warning signs alert people of automatic gate operation and are required when installing the Mighty Mule 500 Automatic Gate Operator Furthermore a walk through gate must be installed if pedestrian traffic is expected near the vehicular gate We recommend using the GTO Bulldog Pedestrian Gate Lock Call the GTO Sales Department at 800 543 4283 for controlled access Bulldog Pedestrian Gate Lock recommended not included Contact Sensors Pedestrian Gate recommended not included Warning Sign Vehicular Gate Photo Beams Contact Sensors Photo Beams recommended not included recommended not included recommended not included GTO s inherent obstruction settings even when properly adjusted may not be sensitive enough to prevent bodily injury in some circumstances For this reason safety devices such as safety edge sensors or photoelectric sensors which stop and reverse gate direction upon sensing an obstruction are suggested for enhanced protection against entrapment Warning Signs AWARNING The warning signs at right must be installed on both sides of the gate see next page for details Moving Gate Can Cause Injury Or Death KEEP CLEAR Gate may move at any time Do
44. ve the problem call the you to track return of equipment GTO Service Department at 800 543 1236 or 850 575 4144 Refer to the serial number located 4 Include a copy of your receipt and securely pack the on the right hand side of the control box and date component s authorized for return to the factory of purchase when calling for assistance Write the RGA number issued to you on the outside of the package in LARGE BOLD PRINT Ship the package s freight prepaid to GTO Inc 3121 Hartsfield Road Tallahassee Florida USA 32303 NOTE Products returned to GTO without a Return Goods Authorization RGA number in LARGE BOLD PRINT on the outside of the package WILL NOT be accepted Items returned to GTO freight collect WILL NOT be accepted Items returned without proof of purchase will not be repaired under warranty The GTO Inc Technical Service Department is open Monday Friday 8 00 A M 7 00 P M Eastern Time Telephone 800 543 1236 Telephone 850 575 4144 Fax 850 575 8950 Web site www mightymule com E Mail techsupport gtoinc com Conversion Chart Converting Metric Units to English Equivalents When You Know Multiply By To Find Symbol centimeters 0 3937 inches in or meters 3 2808 feet ft or kilograms 2 2046 pounds Ib or Converting English Units to Metric Equivalents When You Know Multiply By To Find Symbol inches 2 5400 centimeters cm feet 0 3048 meters m pounds 0 4535 kilo
45. y Do not attempt to drive into the gate area while the gate is moving wait until the gate comes to a complete stop Do not attempt to beat the gate while the gate is closing This is extremely dangerous Do not allow children or pets near your gate Never let children operate or play with gate controls Keep the remote control away from children and unauthorized users store controls where children and unauthorized users do not have access to them KEEP GATES PROPERLY MAINTAINED Always turn power to operator OFF before performing any maintenance Clean the push pull tube with a soft dry cloth and apply silicone spray to it at least once per month Service the gate and gate operator regularly Grease hinges spray push pull tube with high quality silicone spray monthly and replace the battery every 2 3 years 8 10 11 12 To operate this equipment safely YOU must know how to disconnect the operator for manual gate operation see page 2 If you have read the instructions and still do not understand how to disconnect the operator contact the GTO Service Department Disconnect the operator ONLY when the power is TURNED OFF and the gate is NOT moving Make arrangements with local fire and law enforcement for emergency access Distribute and discuss copies of the IMPORTANT SAFETY INFORMATION section of this manual with all persons authorized to use your gate IMPORTANT Save these
Download Pdf Manuals
Related Search