hortus hsl-48
Contents
1. Test Nicht Betrete Urto Hazard Do Non Entrano WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE The exclamation point triangle is used to alert the user to important operating and or maintenance instructions Printed on recycled paper CAUTION Magnetic Field CAUTION Do not locate sensitive high gain equipment such as preamplifiers or tape decks directly above or below this unit Because this amplifier has a high power density it has a strong magnetic field which can induce hum into unshielded devices that are located nearby This field is strongest just above and below the unit If an equipment rack is used we recommend locating the amplifier s at the bottom of the rack and the preamplifier or other sensitive equipment at the top The lightning bolt triangle is used alert the user to the risk of electric shock Shadow ID Numbers Shadow ID numbers allow extra units to share the same ID and follow the settings of the main ID This is useful for larger systems for example anything above a 4 way stereo system where it is only necessary to set up one side of the system and allow the other unit to track it identically Using the shadow IDs in this way also reduces the apparent system complexity within software This is due to the fact that shadow IDs NEVER send back any settings to software and because of this will NOT appear in the list of connected units They can be2. thought of as listening to and acting upon all information addressed to them but not replying Up to 256 shadow units may be connected and assigned the same ID as the main unit but remember that the maximum total units on any network is 256 Shadow ID numbers are accessible when the units interface is configured and will appear after ID number 256 starting from 1 again but designated shadow IDs 2 3 4 5 Remote ID Number 1 Remote ID Number 2 Remote ID Number 3 Page 3 Page 18 User s Manual User s Manual HSL48 HSL48 1 Read all the SAFETY INSTRUCTIONS before using the product 2 This product must be earthed If it should malfunction or break down grounding provides a path of least resistance for electric current to reduce risk of electric shock This product is equipped with a cord having an equipment grounding conductor and a grounding plug The plug must be plugged into an appropriate outlet that is properly installed and earthed in accordance with all local codes and ordinance DANGER Improper connection of the equipment grounding conductor can result in a risk of electric shock 3 Do not use this product near water for example near a bathtub washbowl kitchen sink in wet basement or near a swimming poor or the like 4 This product should be located away from heat sources such as radiators heat registers or other products that produce heat 5 The product should be connected to a power supply only of
3. SL48 HSL48 I nput A Box A Name B o x A 3 Operations 1 Input Box Name Figure 1 Charactor Move 2 Preliminary Set up 1 Design your crossover To do this press MENU and use the BACK or NEXT key to select Xover sub menu and then press ENTER Use the BACK or NEXT key to select Program and then press ENTER 2 Note that when in a menu ENTER is always used to confirm selections 3 Use the EDIT keys on each output channel with the BACK and NEXT keys to select the high pass filters low pass filters parametrics etc Note that when designing a new crossover the high and low pass filters will be set to default values 4 Use the EDIT keys on each input channel with the BACK and NEX T keys to select the gain delay and parametrics available on each input 5 Setup output channed EQ parameter 6 Setup route of each channel and delay HPF LPF Limit parameter Fig 2 4 Fig 2 5 2 Input Delay The maximum available delay of each input is 1000 00mS Figure 3 MS I nput A Box A 0 0000Feet 0 0000Meter 0 000 mS D e l a y Page 7 Page 14 User s Manual User s Manual HSL48 HSL48 I nput A Box A P o l a r i t y No r ma l 5 Input Constant EQ There are 31 bands of constant equalisation available on every input Changing the filter frequency by first encoder Changing the filter gain by second encoder Confirm filter type by pressing ENTER Filter type 3 Input Polarity The po
4. The information contained in this manual is subject to change without notice No part of this manual may be reproduced or transmitted in any form or by any means electronic or mechanical including photocopying and recording of any kind HSL48 Loudspeaker Control System USER S MANUAL DSC48 HD lt BACK NEXT gt ENTER ESC MENU BYPASS PARAMETER DEFAULT 1 DEFAULT 2 DEFAULT 3 INPUT OUTPUT LIMIT 0dBu 48dBu MUTE LIMIT 0dBu 48dBu MUTE LIMIT 0dBu 48dBu MUTE LIMIT 0dBu 48dBu MUTE LIMIT 0dBu 48dBu MUTE LIMIT 0dBu 48dBu MUTE OUTPUT HSL48 Products Service Information Form Owner s Name Shipping address Street City Zip Code Country Phone Number Fax Number Email MODEL SERIAL NUMBER Place of Purchase Name of Dealer Full Address DATE OF PURCHASE Nature of the problem Be sure to describe the conditions that existed when the problem occurred and what attempts were made to correct it Other equipment in your system If warranty has expired payment method Cash Check Visa Master card number Signature Enclose this form with the defective unit Do not mail separately Page 1 Page 20 User s Manual User s Manual HSL48 HSL48 LIMITED WARRANTY THE WARRANTY For a period of one 1 year from the date of delivery to the original purchaser as shown on the original invoice or sales receipt HSL48 warrant
5. equency time ATT RES list 12 Output Low Pass Filter The low pass crossover filter on each output has a frequency range of 10Hz to 30kHz Figure 12 Filter type Frequency Slope F i l t e r L i n k R i l e y S l o p e 1 2 d B 0 c t Output 1 Box 1 LPF F r e q 10Hz
6. er Cord Receptacle accepted voltage 90 240V 50 60Hz 3 Ethernet RJ45 sockets Used for transmission of remote control data over long distance or multiple unit applications 4 Outputs balance XLR connectors 5 Inputs balanced XLR connectors 6 Fan AES Input The HSL48 has a full AES implementation built in as standard This allows the unit to both receive digital audio directly The switching of input can be performed independently and the inclusion of sample rate converters on the inputs allows the unit to accept sample rates from 32kHz up to 192kHz The AES inputs are marked on the rear panel for channels A amp B use input A and for channels C amp D use input C AES EBU inputs are selected through the AES menu Input Sub Menu Output Selection Pressing ENTER and then using the first control chooses either Analogue or Digital Press ENTER again to confirm Selection 8 Upload data from device firstly the data will be uploaded when connecting to device you can choose recall progran from device from the menu communications and do the same process as Fig 2 6 Fig 2 6 7 Downoad data to Device Choose Program menu communications then choose the program from PC and which memory you want to put at the device program 20 to 30 is protected you can down load data to these 10 memories with input password please get the password from your dealer Page 15 Page 6 User s Manual User s Manual H
7. ilter shapes including high and low shelves and bandpass EQ type EQ1 PEQ G a i n 0 0dB F r e q 10Hz Bandwidth 0 050ct Output 1 Figure 13 14 Output Limiter The limiter on each output has adjustable attack and threshold with a release time that is selectable to be a multiplier of the attack time For example as shown below the attack time is 0 3mS and Figure 14 Release Attack Threshold 14 Output Compressor The clip limiter on each output is designed to sit at a threshold just above the standard limiter and has a look ahead attack so that its threshold can never be exceeded The release time can be automatically linked to the high pass filter frequency so that it is set to a value appropriate for the outputs frequency range If this feature is enabled the display will show compressor Auto C l i p l i m 2 0dB Above R a t i o 1 1 Output 1 Box 1 Compresso r anual T h r e s h o l d 2 0 0dBu A t t 0 3ms Rel 8x M ode Output 1 Box 1 ompresso r c Release Attack Threshold Ratio Threshold Compressor Type Figure 14 1 Figure 14 2 M High Pass Filter Auto Attack Time Release Time lt 10Hz 31Hz 45mS x16 720mS 31Hz 63Hz 16mS x16 256mS 63Hz 125Hz 8mS x16 128mS 125Hz 250Hz 4mS x16 64mS 250Hz 500Hz 2mS x16 32mS 500Hz 1kHz 1mS x16 16mS 1kHz 2kHz 0 5mS x16 8mS 2kHz 32kHz 0 3mS x16 4mS Auto mode fr
8. ith the defective unit to an authorized service center They will handle the necessary paperwork and repair Remember to transport your unit in the original factory packaging 1 When sending an DSC48 HD products to the authorized service center for service be sure to fill out the service information form that is enclosed at the end of this manual and include it inside your unit s shipping pack Do not send the service information form separately 2 To ensure the safe transportation of your unit to the authorized service center ship it in an original factory packing container 3 Do not ship the unit in any kind of rack Ignoring this warning may result in extensive damage to the unit and the equipment rack Accessories are not needed Do not send the instruction manual cables and any other hardware CAUTION DSC48 HD lt BACK NEXT gt ENTER ESC MENU BYPASS PARAMETER DEFAULT 1 DEFAULT 2 DEFAULT 3 INPUT OUTPUT LIMIT 0dBu 48dBu MUTE LIMIT 0dBu 48dBu MUTE LIMIT 0dBu 48dBu MUTE LIMIT 0dBu 48dBu MUTE LIMIT 0dBu 48dBu MUTE LIMIT 0dBu 48dBu MUTE OUTPUT DSC48 HD lt BACK NEXT gt ENTER ESC MENU BYPASS PARAMETER DEFAULT 1 DEFAULT 2 DEFAULT 3 INPUT OUTPUT LIMIT 0dBu 48dBu MUTE LIMIT 0dBu 48dBu MUTE LIMIT 0dBu 48dBu MUTE LIMIT 0dBu 48dBu MUTE LIMIT 0dBu 48dB
9. larity or phase of each output may be switched individually as below Figure 4 or I nput A EQ1 GEQ 2 5 H z gt 2 0 H z 0 0dB 31 5Hz 0 0dB 0 0dB Figure 5 3 Setup the Input constant EQ 4 Setup input channel delay parameter and noisegate Fig 2 2 Fig 2 3 Delay MS 463 491ms Metres 161 666 Temp 29C 90F Feet 530 400 Time Temp I nput A Box A G a i n 0 DB 4 Input Gain The range of the control over the input gain is 40dB to 6dB in 0 1dB steps Figure 2 Gain Charactor Move Page 13 Page 8 User s Manual User s Manual HSL48 HSL48 Output 1 Box 1 G a i n 0 dB 8 Output Gain The range of the control over the output gain is 40dB to 15dB in 0 1dB steps Figure 8 Gain Output 1 Box 1 Name B o x 1 7 Output Box Name Figure 7 program running firstly please check the unit is connect to PC by RS485 1 Choose connecting from menu select comport by clicking ok You can use Search ID to find the connect devices also you can enter the unit ID manually It can save your time Fig 2 1 2 The Data currently use the unit will upload to Pc when they connected the screen of unit will shows computer connecting SOFTWARE GUIDE Charactor Move 6 Input Noisegate Figure 6 I nput A Box A N o i s e g a t e E n a b l e T h r e s h o l d 1 2 0 d B u The range of the Noisegate is 120dBu to 0dBu in 1dBu step
10. o supply new equipment in accordance with any earlier specifications DISCLAIMER OF CONSEQUENTIAL AND INCIDENTAL DAMAGES YOU THE OWNER ARE NOT ENTITLED TO RECOVER FROM HSL48 ANY INCIDENTAL DAMAGES RESULTING FROM ANY DEFECT IN THE HSL48 PRODUCT THIS INCLUDES ANY DAMAGE TO ANOTHER PRODUCT OR PRODUCTS RESULTING FROM SUCH A DEFECT WARRANTY ALTERATIONS No person has the authority to enlarge amend or modify this Warranty This Warranty is not extended by the length of time which the Owner is deprived of the use of product Repairs and replacement parts provided pursuant to the Warranty shall carry only the non expired portion of the Warranty THIS STATEMENT OF WARRANTY SUPERSEDES ALL OTHERS CONTAINED IN THIS MANUAL WEEE Mark If you want to dispose of this product do not mix with general household waste There are separate collection systems for used electronic products in accordance with legislation under the WEEE Directive Directive 2002 96 EC and is effective only within the European Union Service This unit has very sophisticated circuitry and should only be serviced by a fully trained technician This is why each unit bears the following label To prevent electric shock do not remove covers No user serviceable parts inside Refer servicing to a qualified technician Worldwide Service Service may be obtained from your local authorized service center To obtain service simply present your sales receipt as proof of purchase along w
11. parametric sections or input graphic equalisers 5 NEXT key moves forward through list of parameters 6 ENTER key enters the chosen menu confirms selections and changes filter types when editing parametric sections 7 ESC exits menus back to the default screen 8 Rotary Encoders Three encoders adjust the relevant parameters as displayed on the screen 9 INPUT EDIT buttons illuminate red when pressed and go into mute mode if press for I second it go in to every input channel EDIT mode 10 OUTPUT EDIT buttons illuminate red when pressed and go into mute mode if press for I second it go in to every output channel EDIT mode 11 INPUT METERS show dBu clipping point of digital to analogue converters Green LED illuminates from 48dBu to 0dBu yellow LED illuminates the clipping 12 OUTPUT METERS show dBu clipping point of digital to analogue converters Green LED illuminates from 48dBu to 0dBu yellow LED illuminates the clipping 13 Scene change recall key Press switch for 1 second processor will load default set program 14 WIFI antenna Please add WIFI antenna before turn on power Fig 2 7 Fig 2 8 9 Choose copy menu to copy data from the edited one to other input output channel 10 Modify Device choose interface menu to set up the start up information of the device 14 Page 5 Page 16 User s Manual User s Manual HSL48 HSL48 1 2 6 4 5 3 Rear Panel 1 Power Switch 2 Pow
12. qualizers Noisegate Input impedance 20 kohms Common mode rejection gt 70 dB 1kHz AD conversion 24 bit Sigma Delta 128 times oversampling linear phase Outputs 8 x XLR OUT electronically balanced Output voltage MAX 7 55 V 20dBu 6 bands parametric equalizers 16 shelving equalizer 6 bands Low Shelving equalizer Hi Shelving equalizer Output impedance lt 100 ohms Min load impedance 600 ohms DA conversion 24 bit Sigma Delta 128 times oversampling Frequency response 10 Hz 30 kHz 0 5 dB S N ratio 110 dB typical Distortion lt 0 01 4 Technical Specifications 5 Ethernet Connection HSL48 lt BACK NEXT gt ENTER ESC MENU BYPASS PARAMETER DEFAULT 1 DEFAULT 2 DEFAULT 3 INPUT OUTPUT LIMIT 0dBu 48dBu MUTE LIMIT 0dBu 48dBu MUTE LIMIT 0dBu 48dBu MUTE LIMIT 0dBu 48dBu MUTE LIMIT 0dBu 48dBu MUTE LIMIT 0dBu 48dBu MUTE OUTPUT Page 17 Page 4 User s Manual User s Manual HSL48 HSL48 1 4 5 2 3 6 7 9 11 12 8 13 10 1 Functions Front panel 1 LCD Screen Shows by default the name of the last recalled memory on the bottom line of the screen Also used to show all parameters as they are edited and all menu selections 2 BACK key moves backwards through list of parameters 3 MENU key activates the main menu 4 BYPASS will flatten the currently selected
13. s Page 9 Page 12 User s Manual User s Manual HSL48 HSL48 F i l t e r L i n k R i l e y S l o p e 1 2 d B 0 c t Output 1 Box 1 HPF F r e q 10Hz 11 Output High Pass Filter The high pass crossover filter on each output has a frequency range of 10Hz up to 30kHz Figure 11 Frequency Filter type Slope 10 Output Delay The maximum delay of each output is 1000 00mS Figure 10 MS 0 0000Feet 0 0000Meter 0 000 mS D e l a y Output 1 Box 1 Unlocking the Unit To unlock the unit press ENTER and then type the code in This can be entered by using the first control to select a character and the second control to move to the next character Press ENTER to confirm Forgotten the Password Don t panic Your unit can still be unlocked In an attempt to improve the security system on the HSL48 and prevent a standard master password from becoming common knowledge the super password is 666666 9 Output Polarity The polarity or phase of each output may be switched individually as below Figure 9 or P o l a r i t y No r ma l Output 1 Box 1 Page 11 Page 10 User s Manual User s Manual HSL48 HSL48 T h r e s h o l d 2 0 0dBu A t t 0 3ms Rel 8x M O d e L i m i t Output 1 Box 1 13 Output Parametric EQ There are six bands of parametric equalization available on every output4 The behaviour of each individual band can be changed to a variety of different f
14. s to the ORIGINAL OWNER of each new product provided it was purchased at an Authorized HSL48 Dealer that it is free of defects in materials and workmanship and that each product will meet or exceed all factory published specifications for each respective model HSL48 agrees to repair or replace at its discretion all defective parts at no charge for labor or materials subject to following provisions WARRANTY VIOLATIONS HSL48 shall take no responsibility for repair or replacement as specified under this warranty if the damaged product has been subject to misuse accident neglect or failure to comply with normal maintenance procedures or if the serial number has been defaced altered or removed Nor will HSL48 accept responsibility for or resulting from improper alterations or unauthorized parts or repairs This warranty does not cover any damage to speakers or any other consequential damage resulting from breach of any written or implied warranty DSC48 HD WARRANTY PROVISIONS HSL48 will remedy any defect regardless of the reason for failure except as excluded by repair or replacement HSL48 will remedy the defect and ship the product within a reasonable time after receipt of the defective product at an HSL48Authorized Service Center TO OBTAIN WARRANTY SERVICE In the event that an HSL48 product requires service the Owner must contact HSL48 or an Authorized HSL48 Service Center to receive an R A N Return Authorization Number and instruc
15. the type described on the operating instructions or as marked on the product 6 The power supply cord of the product should be unplugged from the outlet when left unused for a long period of time When unplugging the power supply cord do not pull on the cord but grasp it by the plug 7 Care should be taken so that object do not fall and liquid are not spilled into the enclosure through openings 8 The product should be serviced by qualified service personnel when A The power supply cord or the plug has been damaged or B Objects have fallen or liquid has been spilled into the product or C The product has been exposed to rain or D The product does not appear to operate normally or exhibits a marked change in performance or E The product has been dropped or the enclosure damaged 9 Do not attempt to service the product beyond that described in the user maintenance instructions All other servicing should be referred to qualified service personnel WARNING Do not place objects on the product s power cord or place it in a position where anyone could trip over walk on or roll anything over it Do not allow the product to rest on or to be installed over power cords of any type Improper installations of this type create the possibility of fire hazard and or personal injury SAVE THESE INSTRUCTIONS WARNING FEATURES Inputs 4 x XLR IN electronically balanced Input voltage MAX 7 55 V 20dBu 31 bands contant e
16. tions on how to return the product to the HSL48 Authorized Service Center or to the factory HSL48 or its Authorized Service Center will initiate corrective repairs upon receipt of the returned product Please save original carton and all the packing materials in case shipping is required All products being returned to the factory or service center for repairs must be shipped pre paid If the repairs made by HSL48 or the HSL48 Authorized Service Center are not satisfactory Owner is instructed to give written notice to HSL48 If the defect or malfunction remains after a reasonable amount of attempts by HSL48 to remedy the defect or malfunction the Owner shall then have the option to elect either a refund or replacement of said HSL48 product free of charge The refund shall be an amount equal to but not greater than the actual purchase price not including any taxes interest insurance closing costs and other finance charges minus reasonable depreciation on the product If a refund is necessary the Owner must make the defective or malfunctioning product available to HSL48 free and clear of all liens or other restrictions MODIFICTTIONS OF EQUIPMENT HSL48 reserves the right to modify or change equipment in whole or part at any time prior to delivery thereof in order to include therein electrical or mechanical improvements deemed appropriate by HSL48 but without incurring any liability to modify or change any equipment previously delivered or t
17. u MUTE LIMIT 0dBu 48dBu MUTE OUTPUT DSC48 HD lt BACK NEXT gt ENTER ESC MENU BYPASS PARAMETER DEFAULT 1 DEFAULT 2 DEFAULT 3 INPUT OUTPUT LIMIT 0dBu 48dBu MUTE LIMIT 0dBu 48dBu MUTE LIMIT 0dBu 48dBu MUTE LIMIT 0dBu 48dBu MUTE LIMIT 0dBu 48dBu MUTE LIMIT 0dBu 48dBu MUTE OUTPUT DSC48 HD lt BACK NEXT gt ENTER ESC MENU BYPASS PARAMETER DEFAULT 1 DEFAULT 2 DEFAULT 3 INPUT OUTPUT LIMIT 0dBu 48dBu MUTE LIMIT 0dBu 48dBu MUTE LIMIT 0dBu 48dBu MUTE LIMIT 0dBu 48dBu MUTE LIMIT 0dBu 48dBu MUTE LIMIT 0dBu 48dBu MUTE OUTPUT Page 19 Page 2 User s Manual User s Manual HSL48 HSL48 The information furnished in this manual does not include all of the details of design and engineering of this particular product not does it cover every possible application or situation concerning its usage which may occur during the installation operation or maintenance of said DSC48 HD product IMPORTANT THE PRODUCT REQUIRES CLASS 2 OUTPUT WIRING TO PREVENT ELECTRIC SHOCK DO NOT REMOVE TOP OR BOTTOM COVERS NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL DISCONNECT POWER CORD BEFORE REMOVING REAR PANEL COVER TO ACCESS GAIN SWITCH Shock Hazard Do Not Enter Choc Hasard N entrent Schocke Hazard
Download Pdf Manuals
Related Search