Home

Invacare Action 2 NG

image

Contents

1. After tilting the wheelchair to the point of equilibrium one assistant at the back holds the wheelchair up against the first step grasping the handles firmly to lift The second assistant lifts the wheelchair above the stairs while holding firmly a fixed part of the frame and holds it while the first assistant takes a step and repeats the opera tion The wheelchair must not be lowered until the last step has been passed and the chair is clear of the stairs To descend stairways Same operation as above however reverse steps as above N Warning Do not attempt to lift the wheelchair by any removable parts such as armrests legrests or footrests Avoid using an escalator which may lead to serious injury in the event of a fall for fixed backrest 1 6 Slopes It is recommended to avoid using ramps with a slope higher than 9 The wheelchair risks tipping over in the event of spinning or side movement figure 4 Upward slopes figure 15 Lean the upper body forward and your centre of gravity will move forward to a more stable position Now move the wheelchair forward with short quick pushes on the hand rims to maintain speed and direction control If you want to rest apply both brakes when stopping Downward slopes figure 16 Lean backward cautiously and your centre of gravity will move backward to a more stable position Now let the hand rims slide in your hands Be ready to react at any momen
2. We recommend that you take the wheelchair to your retailer at least once a year for a complete inspection Regular maintenance allows the identification and replace ment of defective and worn parts which improves the daily operation of your wheelchair Regular inspections to be performed by you or your assistants a General Make sure that the wheelchair folds and unfolds easily Make sure that the wheelchair moves in a straight line no resistance or deviation b Manual brakes Make sure that the manual brakes do not touch the moving tyres Make sure that the manual brakes operate easily Make sure that the joints are not worn and do not have play c Folding system Check the folding system for worn or distorted parts d Skirtguard armrest upholstery Make sure that all the fittings are properly tightened e Armrests Make sure that the armrests are firmly attached but easy to remove f Armpad Make sure that the armpads are in good condition g Seat and backrest upholstery Make sure that the upholstery is in good condition h Rear wheels Make sure that the wheel nuts and precision bearings are tight Make sure that the wheels are parallel to the frame i Handrims Check for rough patches j Spokes Make sure that the spokes are not distorted loose or bro ken k Castors Make sure that the axle is tight by turning the wheel the wheel must gradually come to a stop l Fork steering tube Make
3. Unwin a well known quality manufacturer of safety restraint devices for wheelchairs Restraint system manufacturer may improve its products please contact them for more details 12 4 1 Observations before transport of wheelchairs in vehicles We recommend that wheelchair users should transfer to the seat of the vehicle and use the installed restraint system of the vehicle whenever feasible The wheelchairs are tested in a basic configuration The use in other configurations has not been tested Please contact your dealer for further information Auxiliary wheelchair equipment is either secured to the wheelchair or removed from the wheelchair and secured in the vehicle during transit i e table trays Alterations or substitutions are not to be made to points of the wheelchair or to structural and frame parts without the written consent of Invacare A wheelchair anchored posture belt with metal buckle must be fitted across the wheelchair occupant in addition to the lap and diagonal occupant restraint 3 point belt Belt restraints are not to be held away from the body by wheelchair components or parts such as armrests postural restraints wheels etc Picture 22 The wheelchair must be securely fastened in the vehicle with an ISO 10542 2 approved 4 point belt system according to the methods described in the manual The occupied wheelchair must be tied down in an forward facing position with the parking bra
4. backrest photos 2 amp 2A 43 cm backrest height To save space when transporting folded and unoccupied operate lever A by pulling or pushing it and fold the top of the backrest To return to the initial position bring the top in the vertical position it locks automatically Za make sure that the backrest is properly locked in place before the user settles down in the wheelchair to prevent any injuries Reclining backrest 0 to 30 43 cm backrest height photo 4 The intended use of reclining backrest is to get a relaxing comfort position for the user It is not indented to be used in a dynamic situation and it should be used on horizontal sur face when the backrest is reclined especially when the bac krest angle is more than 10 Anti tippers are recommended for those who need to feel safer or have a specific usage Simultaneously pull the levers A to provides the same angle on both sides release the levers when you reach the desired angle Photo 3 There are 4 angles position by step of 10 Note Push on the backrest canes before operating the levers this is to release the auto locked security system Photo 3A Ate is recommended that this operation be performed only by the attendant Always make sure that the backrest is locked in place to ensure perfect safety for the user Keep away fingers from moving parts levers cylinders mechanisms etc to prevent injuries 17 18 The
5. can make However all the repairs except for inner tubes as well as some adjustments require specific technical training and therefore must be performed by your distributor The Invacaree Action e NG is designed for both indoor and outdoor use with the purpose of helping people who are not able to walk over a long distance Even though your Invacaree wheelchair has been designed to provide a long and trouble free life it is inevitable that wear tear and usage will eventually render the product unusable Invacare amp recommends that the average usable life of this product is five years providing the product has been correctly maintained according to the manufacturers recommendations e GENERAL GUIDELINES Safety and operating limits 1 1 Reaching an object from the chair 1 2 Transferring to other seats 1 3 Tilting 1 4 Tilting Kerbs 1 5 Stairways 1 6 Slopes 2 Operating instructions 2 1 Folding and Unfolding the wheelchair 2 2 Wheelchair propulsion 2 3 Lifting the wheelchair 3 Safety inspection and maintenance 3 1 Performance control 3 2 General inspection 64 Transportation 4 1 Test report 4 2 Observations 4 3 Restraint systems 5 Summary of warranty terms 5 1 Standard terms 5 2 Limitation of liability 66 Operating instructions for optimal safety TABLE OF CONTENTS Page NN DD 01 Ww v OO 10 10 N II 12 13 14 14 14 B DESCRIPTION OF YOUR WHEELCHAIR Prese
6. end Wrench X 2 Quick release axle 19 mm open end wrench mm open end wrench After sale and disposal recommendations It is compulsary to use original Invacare spare parts which you can buy through any Invacare dealer For repair please contact your local Invacare dealer Disposal the metal parts can be disposed of for scrap metal through recycling Plastic parts are disposed of as plastic scrap Disposal must be carried out in accordance with the respective national regulation Please apply to your municipal authorities local government for details about local disposal companies 3 3 Dimensions Min Max Min Max Picture Description valus miam a 1 Maximum Min Max YES Fixed armrest _Picture Description _value value height 200 260 jm 128 Backrest mm Seat effective 380 480 height ANE mm width mm including headrest Adjustable Maximum mm armrest ione 17 height mm P Overall Overall DS 0 585 685 lenght 1035 f gt lt i mm 1060 Notched Maximum armrest 130 dd 9 height mm P Width of Lenght A 09 Nic one Mad 820 845 Rear wheel Maximum gt ISA mm mm diameter 610 are 17 5 ked mm eur p ion istance between eight 935 front wheeland 495 520 Handrim t Wheels mm rear wheel diameter 520 t V d ia Armrests mm e mm p Footrests Height dom Backrest S gr
7. them forward to maintain stability and balance An accurate alignment of the wheels is essential for your safety figure 5 1 1 2 Leaning backward Position wheelchair as close as possible to the desired object so that you can simply pick it up by stretching your arm while sitting in the chair in a normal position figure 6 In any case do not lean backwards because you may cause the chair to tip figure 7 AN wami The hanging of additional load back pack or similar items onto your chair backposts can affect the rearward stability of your chair especially when used in combination with recliner backrests This can cause the chair to tip backwards causing injury Therefore Invacare strongly recommend the use of anti tippers available as an option when using your backposts with additional load back pack or similar items I 2 Transferring to other seats 1 2 1 Sideways transfer This may be done without assistance provided that you are sufficiently mobile and have a strong enough torso Move the wheelchair as close as possible to the seat to which you would like to sit with the castors pointed forward Lock the rear wheels by applying the brakes Fold both footplate up and push the footrest legrest to the side remove swing away the armrest to facilitate the transfer Shift your body towards the place where you want to sit while distribut
8. to slide between your body and the belt The manual brakes are only accessible to the attendant ope rate the handle A to lock the wheelchair in parking position For ease of use it is recommended that the clasp is kept in a central position where possible i e make adjustments to each side of metal buckle belt with double adjuster Please check your posture belt every week to ensure that it is in good condition no damage fraying etc and that it is securely fixed to the wheelchair Zi case the posture belt has to be replaced the new belt ZN The recommended distance between anti tippers small fixation should be conform to the scheme enclosed with each wheels and floor is 3 to 5 centimetres this adjustment is belt delivery the belt should be mounted and adjusted by required with reference to the position and diameter of the your regular dealer rear wheel Make sure that the belts do not get caught in the spokes of Push down the button C and adjust the wheels holding tube the rear wheel for the desired distance based upon the preset holes Not to be used as an alternative to a 3 point occupant res traint in a vehicle A metal buckle posture belt must be used ANis sure that the dog points locates in and protrudes in conjonction with the 3 point occupant restraint through its appropriate location hole in the frame tube in order to prevent any falls Note Make sure that the anti tipper wheel is ALWAYS loca Anti ti
9. Invacare Action NG UK User guide Foreword The information contained in this manual is subject to change without notice Some information is submitted under copyright all rights reserved Any information in this document cannot be photocopied or duplicated without prior written authorization by Invacare As the European and world s leading manufacturer of wheelchairs Invacare endeavours to supply a wide range of wheelchairs to meet all the needs of the user in everyday life However final selection of the wheel chair rests solely with the user and his her qualified health advisor Proper and efficient use of the wheelchair that you have chosen is based upon the medical prescription which was issued for you on the basis of your pathology and the nature of your disability Your wheelchair is especially designed to be used indoors and with certain restrictions outdoor Please look at Z N warning paragraphs Part A General Guidelines Please comply with traffic regulations Stamp of the Distributor Introduction Dear Customer Thank you for purchasing an Invacare wheelchair This model was designed to provide you with all the benefits and features to meet your needs Only quality components were selected for your wheelchair based upon rigorous inspections during the entire manufacturing process This manual describes the operating limits of your wheelchair maintenance operations and adjustments that you or your assistant
10. armrests with central fixation n 1 from now on are equipped with a support adjustable in 2 parts which enables you to reduce the plays and to facilitate the vertical tube extraction it is necessary to tighten or loosen the 4 screws B according to the anticipated result photo 9 19 20 Swing away removable n 2 photos 10 amp II This range of armrests can be swung away to facilitate transfers and disassembling during transport To swing the armrest away push down the dog point A reverse the procedure to reinsert making sure that the dog point B is properly engaged in its housing To remove the armrest swing it back completely and pull it up Reverse the procedure to reinstall The new design includes handle C and hollowed skirt guard D to facilitate front transfer Grip firmly the armrest handle take care of your nails on the skirt guard edges Push on your arms to easily lift yourself up and the attendant can help you to finalise the transfer to the place where you wish to sit In the event the armrest handle covers C become slippery it is recommended to request your dealer to replace them Reter to paragraph 1 2 2 Front transfer for safety instruc tions When folding back down ensure that it locks in place otherwise it can act as a long lever and could fatigue Note the armrests are mounted in pairs on the wheelchair whenever you remove them remember that you have a right and a lef
11. ary the handle upwards Once the brakes are engaged the wheelchair should not move at all Note brake adjustments are based upon the diameter and type of the wheels After repairing a flat tyre or in the event 23 of wear of the pneumatic or solid tyre you may need to adjust the brake s To adjust the brake s loosen the two screws B and slide the brake assembly to obtain the following value between the wheel and the brake shoe in unlocked position 24 2 6 Options 2 6 2 Safety equipment and options 2 6 Propulsion options Safety standard equipment Transit version photos 7 amp 18 the wheelchair is designed Posture belt to be driven only by the attendant To facilitate sideways transfers and save space the wheelchair is equipped with rear wheels of 12 315 mm with solid tyres Buckle fastener photo 19 to close the buckle engage part A into part B to open press C Straps should be adjusted to suit user insert into part B of Note Transit version equipped with a reclining backrest is the buckle and adjust the loop D based on the remaining always fitted with anti tippers length Ensure you are sitting correctly i e fully back in the seat and the pelvis is as upright and symmetrical as possible not forward on one side or tilted back Position the posture belt so that the hip bones can be felt above the belt As a guide adjust the length so that there is just sufficient room for your hand
12. backbrace B photos 4 amp 5 links the two push han dles and must always be in position on recliner version see paragraph 2 6 1 Avoid operating levers A photo 5 during a sideways transfer for example in order to prevent destabili sing the user s position To ensure safety for the user when backrest is reclined we recommend to use anti tippers available as an option Maintenance of reclining backrest mechanism varies with use Please contact your Dealer Based upon the development of your disability you can choose an Action NG backrest that meets your needs Please consult with your Dealer N Tre hanging of back packs or similar items onto your chair backposts can affect the rearward stability of your chair especially when used in combination with recliner backrests This can cause the chair to tip backwards causing injury Therefore Invacare strongly recommend the use of anti tippers available as an option when using your backposts to carry a back pack or similar items 2 1 3 Backrest upholstery Standard upholstery backrests e The padded backrest provides excellent daily comfort for the user who does not need specific support for the upper body In the event that the upholstered backrest slackens ask for a replacement from your Dealer 2 1 4 Footrest supports Standard footrest supports photo 6 swing away during transfers and can be removed during transport Operate lever A by push
13. distance see paragraph B 2 1 4 You can now sit down in the wheelchair Self propelling wheelchair propulsion is achieved through the use of the handrims mounted on the wheels The distance between the wheels axle position and the seat 2 1 2 Folding the chair figures 19 and 20 height can be adjusted to allow you to hold the handrims properly Fold and lock the footrest legrest toward the front of the Qualified medical and paramedical staff will be able to wheelchair provide you with advice regarding the propulsion which is best Swivel the plates into the vertical position Using both adapted to your disability hands take the centre front and back edges of the seat Any wheels adjustments to the set up of your wheelchair see upholstery and lift it Or tilt the wheelchair to one side paragraph 2 2 2 should only be performed at the direction of and close it using the handles on the backrest a competent person who has fully risk assessed the implication of any changes to the wheelchair configuration AN Warning Fold the wheelchair while keeping the seat upholstery upwards to avoid damage by the folding system Caution possible finger pinch 2 3 Lifting the wheelchair First fold the chair see paragraph 2 1 2 always lift the wheel chair by gripping the frame at the points A shown in the figure 21 AN Never lift the wheelchair by removable parts armrests footrests Ensure the backrest posts are secu
14. eelchair to a temperature higher than 40 C To avoid injury keep your fingers away from mobile parts ar mrests folding system legrests footrests and maintain good posture before lifting the wheelchair LN void operating on wet areas as well as gravel grass etc sand and sea water particularly damage ball bearings e DESCRIPTION OF YOUR WHEELCHAIR E PRESENTATION 1 1 Introduction Your wheelchair has been factory set before you purchased it However it must be specifically adapted to your needs The following detailed paragraphs describe the various functions and possible adjustments as well as available options You can make some adjustments yourself while others can be made only by your dealer Important based upon the selected model or options your new Action NG wheelchair may be not equipped with all of the components or options which are described in the following pages NB Some models or options are not be available in your country A This is a warning symbol it is essential that the instructions in these paragraphs are followed in order to prevent personal injury to yourself and others around you D This is an information symbol about possibility to contact your Dealer for more information 1 2 General description see photo Your wheelchair is made of various parts and this manual describes only the main parts We recommend that you become acquainted with the following terms in order to b
15. etter understand your wheelchair operation e The seat consists of the seat and backrest upholstery the backrest and armrests This unit is designed to provide optimal comfort e The swing away footrest support this is the suppor ting part between the frame and the footrest which swivels to facilitate transfers and can be removed during transport e The footrest consists of an adjustable tube and the footplate which supports the foot 15 e The folding frame consists of side frames and a folding system including the seat rails These parts constitute the frame which is the supporting component of the wheelchair and its strength is well tested checked at 125 kg e The rear wheel consists of the wheel axle and handrim The position of the rear wheels relative to the seated user determines the rearward stability and also the ease by wich the user can propel the wheelchair using the handrims They are mounted on wheel support brackets Changing the rear wheel position will have a significant impact on the stability of the user e The castor consists of the front wheel and the fork The castors provide front contact with the ground and determine the steering by the direction of the forks e The manual brake is a parking brake The two manual brakes are used to secure the wheelchair when stationary Backrest upholstery Armpad Backrest Armrest Rear wheel Seat upholstery Rear wheel support Rear whee
16. hair and outside it Any movement you make whilst sat in your wheelchair will move the combined centre of gravity Gc of you and the wheelchair Gw You will remain stable in the wheel chair whilst the line of your combined centre of gravity lies within the points of contact of the forward and rear wheels with the ground Weight Limit The maximum recommended weight of the user is 125kg However the level of activity is an essential factor For example an active user who weighs 75 kg may subject the wheelchair to more stress than user who weighs 100 kg To this purpose we recommend that you consult your retailer when choosing the model of wheelchair based upon your daily life style 1 1 Reaching an object from the chair The limitations on reaching out from a wheelchair indicated in the following diagrams have been calculated based on a representative sample of wheelchair users Only the arms should be extended beyond the seat of the wheelchair figure 2 In any case the body and head shouldn t remain without the boundaries of the seat figure 3 1 1 1 Leaning forward Do not extend your chest beyond the armrest figure 4 In order to reach an object in front of you you must lean and bend down therefore you must use the castors as a tool pointing
17. ing sideways and swivelling towards outside or inside in case there is not enough space To return to the initial position align the footrest support it locks auto matically To remove the footrest support simply pull up after unlocking the assembly Reverse the procedure to reassem ble while still in the unlocked position The distance between the lowest part of the footrest and the ground must be at least 40 mm Footrests photo 7 the footplate can be lifted during transfers footrests are height adjustable Loosen the screw A to adjust to the desired height firmly tighten the screw after adjustment Straps to ensure a good position of the feet the heelrest strips are adjustable by Velcro fasteners Note the standard footrest supports are mounted in pairs on the wheelchair whenever you remove them remember that you have a right side and a left side AN Never lift the wheelchair by the footrest supports Keep your fingers away from movable parts during folding disassembling or adjustment to prevent injuries 2 1 5 Armrests Removable Simple n I photos 8 amp 9 to remove armrests simply pull them up Previously press on the push pin C located at the bottom of the armrest vertical upright Reverse the proce dure to reinstall them To adjust their height 3 positions remove the screw A adjust to the desired height and repo sition the screw A tighten without forcing The
18. ing your weight to the arms and hands figures 8 amp 8A While moving from the wheelchair to the seat your body will have little or no support Where possible use a transfer board during transfers 1 2 2 Front transfer figure 9 If you are more or less able to stand up and if your upper body is strong and mobile enough you can transfer forward to another seat If you find this movement difficult we recommend that you obtain some assistance from an attendant or carer to ensure the transfer is as smooth and safe as possible Lock both brakes and ensure both castor wheels are facing the forward position Please note that the brakes should not be used in any case as support for transfers Fold the footplate up then grip firmly the armrest handle take care of your nails on the skirt guard edges Push on your arms to easily lift yourself up and the attendant can help you to finalise the transfer to the place where you wish to sit Warning Position yourself as close as possible to the place where you wish to sit When transferring position yourself as far back as possible in the seat to prevent breaking screws damaging the seat upholstery or causing the wheelchair to tip forward Lock the two brakes they should not be used in any case as support for transfers Never stand on the footrests when you are getting in or out of the wheelchair figure 10 I 3 Tilting bala
19. ke applied The wheelchair backrest should be positioned as close as possible to 90 degrees Please observe that even if these products and recommen dations are provided in order to increase safety injury to vehicle occupants still might occur in the event of a collision or other accidents and no guarantee is given in this respect Correct and incorrect placements of 3 point belt picture 22 4 2 Restraint systems picture 23A details A amp B Non contractual picture only for information Please refer to best practice recommended instructions from the safety belt manufacturer A Front restraints with straps picture 23A amp detail A Connect the front straps around the front part of the frame See location of the attachment labels 2 Release brakes and apply tension front straps by pulling the wheelchair backwards from the rear 3 Re apply wheelchair brakes B Rear restraints picture 23B for Self propelling I Attach the snap hooks on the rear straps to the rear orange ring A just below the backrest tube bracket 2 Tighten the straps C Posture belt I The posture posture belt is mounted on the back frame picture 24 2 Check that the posture belt on the wheelchair is correctly fastened If posture belt on the wheelchair is missing we recommend that the user should transfer to the seat of the vehicle if possible The posture belt should be used in addition to but never as a substitute fo
20. l axle Adjustable footrest tube Handrim P Manual brake Footplate Folding frame Swing away footrest Front wheel Adjustments 2 1 Seat 2 1 1 Seat upholstery Standard seats Nylon upholstery seat with or without Velcro fastener the Velcro fasteners are required for the proper positioning of the cushion photo please make sure that the cushion is properly positioned on the seat Depth adjustable seat fold the seat sightly Lift up the front part Pull into required depth e Padded seat it provides comfortable support to the user Standard seats are not adjustable in the event that they become slack it is recommended that you ask your dealer to replace them A Always use upholstery equipped with Velcro fasteners when you have a cushion in order to prevent sliding Adding a cushion to the seat will raise your height above the ground and can affect your stability in all directions If a cushion is changed it may also change the users stability Invacare provides a wide range of seat cushions adapted to your needs Please contact your dealer The upholstery and casing of the seat will wear please contact your dealer for possible replacement Dne sure that the seat is properly positioned on the 2 seat rails to provide safety and comfort for the user Keep your fingers away from movable parts to prevent injuries during folding and unfolding 2 1 2 Type of backrests Folding
21. lock the axle with an Imm open end key Nas make sure that the spacer D is in place Make sure that the axle and the locking balls are clean wipe out every month with a rag soaked with fine oil To prevent falls it is essential that the button A and the locking balls C are disengaged providing a perfect lock of the rear wheels The quick release axle is a precision part take care of shocks and clean regularly to ensure the good working of the mecha nism 2 4 Castors 2 4 1 8 wheels The front wheels are available in 8 200mm diameter Note refer to paragraph 2 3 1 for regular maintenance 2 4 2 Forks Two different fork positions are available based upon the selection of floor to seat height Please take advice from your dealer if you want to re place a fork or the castors or rear wheels 2 5 Brakes A Please make sure this adjustment is always done as 2 5 1 Manual brakes describe whatever the chair configuration is Solid tyre X 6 mm Pneumatic tyre X 5 mm The manual brakes photo 15 are designed to secure the wheelchair during long stops They are not intended to slow Firmly tighten the screws B after adjustment down the wheelchair or to be used as support during a Keep your fingers away from movable parts to prevent injuries transfer They must be operated simultaneously In order to brake push the handle A forward The handle folds back to facilitate transfers Draw as a prelimin
22. ncing on the rear wheels For greater safety this operation must be performed by an attendant The attendant should be aware of the required physical effort and use appropriate positioning in order to relieve the strain on his her back keep a straight back and bend your knees during this operation To tilt the wheelchair the attendant must firmly grab the han dles making sure both are properly fixed Warn the occupant in the wheelchair before tilting it and remind him her to lean backwards and make sure that both feet and hands of the user are clear of the wheels Place a foot on the footstep tube and move continuously until the chair reaches the equilibrium point At this stage the assistant will feel a difference in weight distribution which usually occurs at approximately 30 At this point the wheelchair can get over the obstacle easily Finally the attendant slowly and gradually lowers the front down to the ground while firmly holding the handles I Waren Be aware of detachable parts such as armrests or legrests they must NEVER be used as lifting supports as they may be inadvertently released resulting in possible injury to the user and or attendant Do not lower the wheelchair suddenly even if it is several centimetres from the ground as this may result in injury of the user 1 4 Tilting Kerbs To get on the pavement Method figure I1 The attendant positions the wheelchair in front of the
23. ndustrial de Celr 17460 Celr Girona Espa a 34 0 972 49 3200 Fax 34 0 972 49 32 20 Invacare Poirier SAS Route de St Roch F 37230 Fondettes France 33 0 2 47 62 64 66 Fax 33 0 2 47 42 12 24 Invacare Mecc San s r l Via dei Pini 62 1 36016Thiene VI Italia 39 0 445 380059 Fax 39 0 445 380034 Invacare Ireland Ltd Unit 5 Seatown Business Campus Seatown Rd Swords County Dublin Ireland 353 8107084 Fax 353 8107085 Invacare NZ 4 Westfield Place Mt Wellington Auckland New Zealand kundeservice 64 22 57 95 10 Fax kundeservice 64 22 57 95 01 Invacare AS Grensesvingen 9 0603 Oslo Norge kundeservice 47 22 57 95 10 Fax kundeservice 47 22 57 95 01 Invacare PORTUGAL Lda Rua Estrada Velha 949 4465 784 Le a do Balio Portugal 351 225105946 Fax 351 225105739 Invacare AB Fagerstagatan 9 163 91 Sp nga Sverige kundtj nst 46 0 8 761 70 90 Fax kundtj nst 46 0 8 761 81 08 Invacare B V Celsiusstraat 46 NL 6716 BZ Ede Nederland 3 0 318 69 57 57 Fax 31 0 318 69 57 58 Invacare Ltd South Road Bridgend Industrial Estate Mid Glamorgan CF31 3PY United Kingdom T Customer Service 44 0 1656 647 327 Fax Customer Service 44 0 1656 649 016
24. ntation l l Introduction 1 2 General description 2 Adjustments 61 Seat elements 1 1 Seat upholstery 1 2 Type of backrest 1 3 Backrest upholstery 1 4 Footrest supports 1 5 Armrests Frame 2 2 1 Side frame 2 2 2 Folding system 2 3 Rear wheel 2 3 1 24 wheels 2 3 2 Handrims 2 3 3 Axles 2 4 Castors 2 4 1 8 wheels 2 4 2 Front fork 2 5 Brakes 2 5 1 Manual brakes 2 6 Seating options 2 6 1 Propulsion options 2 6 2 Safety equipment and options 2 2 2 2 2 2 2 3 Specification and tool s 6 Standard wheelchair specifications 3 3 l 2 Tools for adjustments and regular maintenance Not supplied 3 Dimensions Page 15 15 16 16 17 18 18 19 20 20 20 21 21 21 22 22 22 22 23 23 24 24 24 26 26 e GENERAL GUIDELINES l Safety and operating limits For a safe operation of your wheelchair the following para meters should be observed Stability and balance Your wheelchair has been designed to provide the stability you need during normal daily activities Any movement in the wheelchair will have an impact on the position of the centre of gravity which may lead to the wheelchair tipping and a fall To improve your safety when you move a lot or you trans fer your weight from one place to another we recommend using seat belts Weight distribution figure 1 Many actions cause the user of a wheelchair to reach out lean over or move about within the wheelc
25. ot extend to the consequential costs resulting from fault clearance in particular freight and travel costs loss of earnings expenses etc Invacare shall not be liable for Natural wear and tear Inappropriate or incorrect use Defective assembly or setting up by the purchaser or third parties Defective or neglectful treatment Use of unsuitable spares Operating instructions for optimal safety Maximum user s recommended weight 125 kg Do not attempt to reach objects if you have to move forward in the seat Do not attempt to pick up objects from the floor by reaching down between your knees Do not lean over the top of the upholstery back to reach objects located behind you this may cause you to tip over Always engage both manual brakes simultaneously Manual brakes are parking brakes they must not be used in any way to slow down the wheelchair or as support during transfers Do not tilt the wheelchair down kerbs or steps without using an assistant Press down on the lower tube of the frame as well as pulling on the push handles Do not carry the wheelchair up or down stairway or esca lators with the user seated in the wheelchair with only one attendant This may cause serious injury Do not use the wheelchair unless it has the proper tyre pressure rear 350 kPa Do not overinflate the tyres this may cause the tyres to explode and cause bodily harm Do not expose the wh
26. ound to vera backseat 460 o 0 30 d Seat plane wolght i mm py 3 E when empty 16 5 17 2 g kg Height from ground to ue i Height User s front seat 485 s 80 1 without rear maximum Ni mm o wheel 660 weight 125 mm B kg Backrest Distance height between ae Turning boo uh Hs mm 430 footrest and 350 480 circle 870 doa 8 7 seat mm E Z LI mm removed pa y Kg kg Wheelchair bd m height when Cushion ylon 705 armrest and 250 350 depth 50 f Seat material BS EN backrest is EDANE p m Fire class folded mm nm mm L i 1021 1 2 27 Yes you can 1531661 UK V1 09 2009 Invacare France Operations SAS EM MEER a Route de Saint Roch 37230 FONDETTES Invacare Australia Pty Ltd I lenton Place North Rockes NSW 2151 Australia 61 2 8839 5333 Fax 61 2 8839 5353 Invacare n v Autobaan 22 8210 Loppem Brugge Belgium amp Luxemburg 32 50 831010 Fax 32 50 831011 Invacare AIS Sdr Ringvej 37 2605 Br ndby Danmark Zi kundeservice 45 0 3690 0000 Fax kundeservice 45 0 3690 0001 Invacare Aquatec GmbH AlemannenstraBe 10 D 88316 Isny Deutschland 49 0 75 62 7 000 Fax 49 0 75 62 7 00 66 European Distributor Organisation Invacare KleistsraBe 49 D 32457 Porta Westfalica Deutschland 49 0 31 754 540 Fax 49 0 57 31 754 541 Invacare SA c Areny s n Poligon I
27. pave ment facing forward Press down on the lower tube of the frame or on tipping levers delivered as an option as well as pulling on the push handles Attendant tilts the wheelchair backwards until the castors reach the pavement attendant pushes the wheelchair forward until the rear wheels are against the kerb and again pushes the wheelchair until the rear wheels climb over the kerb Method 2 figure 12 In this case the attendant stays on the pavement and tilts the wheelchair in a backwards position with the rear wheels against the kerb The attendant tilts the wheelchair bac kwards until it is balanced and pulls the wheelchair with a steady movement until the rear wheels climb over the kerb then he she lowers the castors while making sure that the chair is far enough on the pavement so that the castors do not fall into empty space To get off the pavement The attendant positions the wheelchair facing forward on the pavement and tilts it backwards until it is balanced then he she pushes the wheelchair forward until the rear wheels touch the road after getting over the obstacle then he she gradually lowers the castors to the ground 1 5 Stairways Because this is a difficult movement we recommend using two attendants one in front of the wheelchair and one behind the wheelchair N Warning we recommend that users over 100 kg in weight do not use this stairway manoeuvre To climb stairway figure 13
28. ppers photo 20 prevent back tipping which ensures ted out side the rear wheel volume safety when using a reclining backrest driving on slopes or All these adjustments and changes of position must be perfor 25 crossing obstacles These are removable push down the med by a professional technician because these can affect the eA ae pu dd E E stability and the safety of the user Please consult your dealer tube Safety optional equipment Anti tippers can remain in place when the wheelchair is not used perform a half turn by activating the button B and rotating 26 8 Specifications and tool s 3 1 Standard wheelchair specifications Maximum user weight Seat width Seat depth Floor seat height Rear wheel Castors Parking brake Backrest Armrests Footrest supports Seat upholstery Frame Wheelchair average weight 125 kg 38 40 5 43 45 5 48 cm 43 cm 48 5 cm 24 610 mm solid tyre 8 200 mm solid tyre Manual brake with indexed brake shoe Folding reclining Removable removable and swing away Removable and swing away Black nylon on reinforced upholstery Aluminium epoxy coated 16 5 kg 3 2 Tools for adjustments and regular maintenance not supplied Function Tool Brake 5 mm Allen key Footrest tube 5 mm Allen key Footplate 5 mm Allen key Simple armrests n I 4 mm Allen key 10 mm open end wrench Armpad T20 Torx key Castor 13 mm open
29. r an approved passenger restraint system 3 point belt D Fastening of 3 point belt vehicle safety belt device Although all three points may be anchored to the vehicle floor the diagonal belt passing over the users shoulder should be routed through a point above and behind the seated user which is fixed to the vehicle sides before passing down to the floor The 3 point belt should not be kept from the user s body by the parts of the wheelchair 13 14 Summary of warranty terms 5 1 Standard Invacare terms and conditions This is to certify that your manual wheelchair is warranted by Invacare for a period of 2 years for the frame and cross bars all others parts 2 years also but subject to the following conditions If a defect or fault is discovered the supplier dealer from whom the appliance was purchased should be notified imme diately The manufacturer will not accept responsibility for damage caused by misuse or non observance of the instructions set out in the user manual During the period of warranty any parts that have become defective due to faulty workmanship or materials will be renewed or repaired without charge by the Invacare dealer supplier The warranty will be forfeited should any unauthorised alteration be made to the equipment The Purchaser s statutory rights under the Consumer Protection Act are not affected 5 2 Limitation of liability This warranty does n
30. rely in place 10 Safety inspection and maintenance 3 1 Performance control As the user you will be the first to notice any possible operational defects with your wheelchair The following table indicates the easiest troubleshooting symptoms to identify and the preliminary inspection that you can perform In the event that the symptoms persist after adjusting the pressure in the tyres please consult your retailer The inner tubes of the wheels are the only components that you can repair yourself see paragraph B 2 3 If the screws and nuts are not tight enough or loose the axle fork angle is not perpendicular to the ground please consult your retailer to get a competent person to re set them to the correct position and tighten appropriately Recommended torque minimum M5 4 Nm M6 7 Nm amp M8 17 Nm The The The The Creaking Play in and th wheelchair wheelchair wheelchair te e i swerves swerves turns or Sie clinking Wheelchair Inspections to the to the left moves 8 right slowly Make sure that pressure in the e e e pneumatic tyre is correct cf B 2 3 Make sure that the e e e e bolts are tight Check the adjustment e e e on the fork angle Make sure that the 2 castors come in e e e contact with the ground at the same time 3 2 General inspection Your distributor who has the required technical expertise is responsible for any wheelchair repairs
31. sure that all the fittings are well tightened m Pneumatic and solid tyres Check the pressure of the pneumatic tyres Rear 350 kPa check the wear of the solid tyre tread n Cleaning and disinfection Cleaning Use only damp clothes and gentle detergent Do not use abrasive or scouring liquid Do not use high pressure cleaning devices on ball bearings front amp rear wheels fork axles Make sure you dry the wheelchair if it is wet e g after washing it or going out in the rain Disinfection Spray or wipe disinfection using a tested and recognised product is permitted Please pay attention to the manufacturer s instructions of the medical product disinfectant you are using Transportation Transport of wheelchairs in vehicles The Invacare Action NG has been tested for safety in colli sions according to ISO 7176 19 2001 Invacare Action NG can be used for transport in vehicles that have been specially adapted for this purpose The wheelchair must be securely fastened in the vehicle according to the methods described on the following pages Remember that the best solution is always to move the user from the wheelchair into a normal car seat and to stow the wheelchair safely and securely in a 11 separate compartment Test no S10757 Self propulsion Customer Invacare UK Ltd Date 24 04 2009 The safety restraint devices used in this test must be appro ved according to ISO 10542 We have chosen to work with
32. t side NTE lift the wheelchair by the armrests Keep your fingers away from movable parts during folding disassembling or adjusting to prevent injuries 2 2 Frame 2 2 1 Folding system It consists of two cross bars which integrates seat rails To fold and unfold your wheelchair see chapter A General paragraph 2 1 2 2 2 Side frame The sides or side frames are designed to accommodate the steering tubes for the castors and multiple adjustment wheel mounting for rear wheels These wheel mountings allow two height positions and two longitudinal positions Standard serial delivery with fixed or folding backrest Passive backward for better stability serial with reclining backrest and Transit 12 version AN The above information is given to the user for informa tion only Any wheels position of your wheelchair should only be per formed at the direction of a competent person who has fully risk assessed the implication of any changes to the wheelchair configuration Please consult your dealer All these adjustments and changes of position must be performed by a professional technician upon agreement by your prescribing physician Please consult with your dealer 2 3 Rear wheels 12 3 1 24 wheels The 24 610 mm rear wheels are spoked wheels They can be delivered with pneumatic or solid tyre A flat tyre photo 12 must be removed in order to be repaired Remove the rim assembly tyre and inner t
33. t to control speed and direction AN Warning The position of the rear wheel axle and the angle of your wheelchair s backrest are two of the key adjustments that can affect your stability whilst sat in the wheelchair see figure 14A Avoid turning suddenly and never try to climb and descend a ramp diagonally figure 17 eg Standard configuration N Warning It is recommended to avoid using ramps with a slope greater than 9 degrees and do not attempt to turn whilst on a slope The wheel position is usually factory set and should not be change unless by the direction of a competent person who must have assessed the impact of the change on your stability in normal use If your wheelchair is fitted with a recliner backrest it is recommended that anti tippers are also fitted and used whenever the backrest is reclined from the upright position Operating instructions 2 1 Unfolding and Folding the wheelchair 2 1 1 Unfolding the wheelchair figure 18 With one hand grab the armrest or the seat support tube on one side of the wheelchair and slightly tilt it towards you so that the rear wheel and castor lift from the ground With the other hand push on the seat tube until upholstery is fully extended and seat tube sits in receiver Then engage the two manual brakes open the footrest 2 2 Wheelchair propulsion legrest and check the ground clearance footrest ground
34. ube repair or replace the inner tube reinsert in the tyre and repo sition the assembly on the rim Comply with the inflation pressure specified on the sidewall of the tyre Note remember that in order to maintain the interchangea bility of the chair wheels equipped with quick release axles the pressure in the two tyres should be the same A Check and adjust the brakes to ensure they are still correctly positioned and function as required VAA exceed the pressure specified on the sidewalls of the tyre otherwise the tyre may explode and cause injuries Pneumatic tyres wear out In addition the roughness of the ground surface and driving have an impact on their 21 longevity Replace them regularly to avoid punctures caused by puncture Please consult with your Dealer 2 3 2 Handrims They provide the wheelchair propulsion They are made of anodized aluminium NIE are constantly in contact with your hands Make sure that they are not damaged 22 2 3 3 Axles The axles connect the wheels and frame Quick release axles photo 13 depress the button A and insert the axle in the wheel hub Position the assembly in the bearing B of the multiple adjustable wheel mounting until it locks in place The locking balls C must rise above the bearing No significant side clearance is allowed To reduce clearance as much as possible photo 14 remove the axle and adjust the nut using a 19 mm key then b

Download Pdf Manuals

image

Related Search

Related Contents

CATALOGUE - Le club de math dans les écoles  Artefacto de iluminación Hunter para exteriores Instrucciones de  VOTRE DOSSIER DE DEMANDE D`OUVERTURE  Betriebsanleitung - Sander Fördertechnik    Hansgrohe 31067821 Instructions / Assembly  Hardware Manual V1.6  5 - American Standard    

Copyright © All rights reserved.
Failed to retrieve file