Home

COR user manual

image

Contents

1. Optical connection meets class 1M laser safety requirements of IEC 60825 1 2001 and US department of health services 21 CFR 1040 10 and 1040 11 1990 when operated within the specified temperature power supply and duty cycle ranges Optical signal levels The optical output level is typically 1 dBm to both directions However the allowed optical input levels are different and are for forward input direction 5 21 dBm and for return input direction 0 dBm 21 dBm When testing the units it is advised in addition to a short fibre patch cable to use always an optical attenuator to guarantee system safe operation In most cases a recommended attenuator value is at least 5 dB Please check also that a high quality doped fibre attenuators are used air gap attenuators may cause difficulties on link association due to a poor reflection loss performance Optical signal routing inside the optical repeater module Forward input Return output Forward Return Return input 622 Mbps 2 5 Gbps 622 Mbps 1 25 Gbps Forward output e D 1550nm Ch15 COR series optical repeater user manual Technical specifications Optical forward path Received wavelenght Transmitted wavelenght Input level range Output power Forward path link speed Optical connector type Optical return path Received wavelenght Transmitted wavelenght Input level range Output power Return path link speed Optical connector t
2. Teleste Corporation Teleste Corporation Video Networks P O Box 323 FIN 20101 Turku FINLAND www teleste com WEEE directive Directive 2002 96 EC of the European Parliament and of the Council on waste electrical and electronic equipment WEEE obliges that producers appropri ately mark electrical and electronic equipment with the symbol indicating separate collection This obligation applies to the equipment put on the market in EU after 13 August 2005 Teleste devices which belong to the scope of the directive have been marked with the separate collection symbol shown below The marking is according to the standard EN 50419 The symbol indicates that the device has to be collected and treated separately from unsorted municipal waste User manual revision history note The latest version is always available in pdf format on our web site www teleste com COR series optical repeater user manual Notes COR series optical repeater user manual 10 COR series optical repeater user manual TELESTE www teleste com
3. a regulated output e g CPS231 Please refer to separate documention for module adapters and mains adapters CONTROL The permitted supply voltage range is 10 5 14 VDC The current con sumption is max 100 mA 12V DC The permitted operational tempera CMA021 module adapter 1 Grounding connector 2 Supply voltage connector Other interfaces are not in use Ge A SE CPS231 power supply with connector AWM eee LC VW 1 18AWGX2C 4 COR series optical repeater user manual Available ITU G 694 2 wavelength channels for COR units front view J all DOMH The optical connector type is SC APC 8 COR series optical repeater user manual Fibre connection COR optical repeaters are designed to operate on ITU specified CWDM optical channels Configurable properties are that wavelenght for forward direction and return direction can be choosen separately However in a typical CFO OP X system channel is the same to both directions The optical connector type is SC APC 8 When installing the fibre optic cable do not exceed the minimum bending radius when connecting cable to the system For correct optical operation ensure that Protect opened connectors always with dustcaps Use only 8 angle polished SC APC connectors other connector types will damage the interface Clean all connectors before mating by using metyl or isopropyl alcohol and dry connectors by compressed air
4. User manual COR Optical repeater for singlemode fibre COR series optical repeaters are meant for systems requiring extreme fibre transmission distances They provide an additio nal 20 dB link budget for any ITU T compliant CWDM wavel ength or standard 1310 nm used in a CFO system E P OPTICAL REPEATER Video Networks COR series optical repeater user manual 59300297 rev002 Contents COR 0ptical EENEG ee Gen EE EE ee COR optical repeater front panel eee ee eee eee na nana SEES ote ho ee EE e din n nai aa ne De tei nite a in il aa Frame INS Lai EU EI tse raceme em ve ae tec senate tient acto ee Were il elteren IERI ee ee eee a RR RR ee ee RIN RR CINE he eer Stand DEE EE ne EE leie OS CON BEE OPICA E le EE Si ele e Technical speci En CN ee eg TR En COR series optical repeater user manual COR optical repeater Configurable bi directional optical repeater to cover extreme transmission distances over singlemode optical fibre Welcome and thank you for purchasing Teleste s CFO Products COR repeaters are part of the extensive CFO OP X platform that complies to ITU G 694 2 CWDM grid Also basic 1310 nm operation is supported These non regenerative repeaters provide a cost effective way to cover extreme transmission distances over optical fibre Depend ing on system up to two or three repeater units can be connected in series to make a line in which each leg have a maxim
5. um of 20 dB link budget available for bi directional operation The COR repeaters are configurable products meaning that the operational wavelenght can be selected upon customer specification A typical repeater configuration supports fully bi directional operation but has also option to be defined for uni directional operation as well The COR repeaters are optically compatible with all earlier generation digital CFO video modems SMF 1310 nm and CWDM models The COR series fits into all standard CFO installation systems allowing both rack or standalone adaptor type operation The COR series is temperature hardened As with all CFO platform products these specific models do meet all typical EMC as well as other environmental and manufacturing related requirements e Bi directional operation in same wavelength e Complies to ITU G 694 2 CWDM grid e High performance e Same units for rack mount or stand alone e Mechanically compact and ruggedised e International EMC and environmental conformance e Compatible with all CFO installation systems e Optically compatible with older generation CFO video modems e g CFOx41 and CVM series COR series optical repeater user manual COR optical repeater front panel Mm 9 gt D w o 1550nm Ch15 COR Optical Repeater 1 Locking screw 4 pcs 2 Port 1 optical forward input return output SC APC 8 3 Port 2 optical return input forward output SC APC 8 4 Ser
6. vice connector RJ 45 female 5 Module indicator led 6 Handle with wavelenght and channel information See further information on dedicated sections COR series optical repeater user manual CAUTION THESE OPTICAL UNITS USES CLASS 1M LASER DIODE DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS APPLICABLE STANDARD IEC60825 1 2001 The COR units are configurable bi directional optical repeaters for CFO OP X platform that complies to ITU G 694 2 CWDM grid Frame installation The COR module is to be pushed along the guide rails into the installation frame e g CSR216 or 316 series and secured with the four locking screws The unit can be freely positioned in any slot in the frame The empty positions in the frame should be blanked off with cover plates The supply voltage is to be provided by a CPS384 or CPS390 power supply unit which are installed back of frame Module indicator led The COR contains a MODULE indicator which informs generic status of the unit Colour Green Normal operation Supply voltage is not in the permitted range or a hardware failure MODULE indicator operation rear view CONTROL Stand alone installation The unit can be installed for stand alone use by using a CMA021 module adapter installation for 1OHP wide CFO series units The module should be mounted to a vertical surface The 12 VDC supply voltage is supplied by the means of a separate mains adapter with
7. ype 1290 1330 and 1470 1610 nm configurable CWDM ch or 1310 nm 5 dBm 21 dBm 1 dBm 622 Mbps to 2 0 Gbps SC APC 8 1290 1330 and 1470 1610 nm configurable CWDM ch or 1310 nm 0 dBm 21 dBm 1 dBm 622 Mbps to 1 25 Gbps SC APC 8 General Supply voltage 12 V 100 mA Power consumption max 1200 mW Dimensions H x W x D 3U e 10HP 190 mm without CMA Weight 0 5 kg Operating temperature 34 74 C Storage temperature 40 85 C Humidity 0 95 non condensing EMC compatibility EN61000 6 3 EN50130 4 CE Notes Factory set upon customer configuration CWDM channels 11 18 or basic 1310 nm Class 1M Laser Product Typical values unless otherwise stated Application example Multiwavelenght CWDM system Wavelenght specific repeaters max 20 dB link budget max 20 dB link budget max 20 dB link budget Single wavelenght point to point system 20dB 20dB 20dB ISIO iim SZ RX gt repeater repeater x61 VEY Or pipe COR series optical repeater user manual 7 Copyright acknowledgements Information in this document is subject to change without notice and does not represent a commitment on the part of Teleste Corporation Copyright Teleste Corporation All Rights Reserved No part of this document may be reproduced transmitted stored in a retrieval system or translated into any other language without the express permission of

Download Pdf Manuals

image

Related Search

Related Contents

BETRIEBSanlEITung  Maretron FFM100 GPS Receiver User Manual  GOCLEVER QUANTUM 2 500 8GB Black  DH 40FR - HITACHI Power Tools  Serie PAF  Manual de usuario Lesiones      Notice - Castorama  Conditions utilisation plateforme marchés publics (pdf  

Copyright © All rights reserved.
Failed to retrieve file