User`s manual - TAG Heuer Timing Systems
Contents
1. PS almanac this allows fast synchronization WARNING When you remove the antenna connector firmly hold the connector Never draw by the cable 5 Remarks on GPS gt If GPS signal is Lost poor positioning of the antenna the printer indicates Synchro GPS lost The time of day The display of the time will flicker along with GPS LOST If the GPS signal is synchronised again the printer indicates repositioning of the antenna GPS Active Synchro GPS found Time of the day DEV 3 0 usec for example Remark Automatic resynchronization of the timebase of the CP 540 temporary loss of GSP signal is acceptable in conditions where the drift of the time does not exceed 100 usec 1 10 000 of a second In case of resynchronization the drift DEV is always printed If the drift value is over 100 usec the base time of the CP 540 is the reference for the rest of the time keeping The GPS can be switched OFF If the Docking is disconnected the printers indicates Docking disconnected Synchro GPS lost Time of the day When the Docking is reconnected the printer indicates Docking Connected with its serial number and Software version GPS Searching with GPS UTC Delta 16 sec GPS Active Synchro GPS founded Time of the Day DEV 2 4 usec for example 6 Information gt gt gt The GPS Docking has banana output connector to provide a signal TOP MINUTE which is us2. eful to synchronize other timing systems If the GPS is used only for the CP 540 it is recommended to wait 4 5 mins before to switching it OFF memorize the GPS precision The GPS Docking has an Input output Master Slave This mode of synchronization between several CP 540 s is very useful for the timekeeper to guarantee absolute precision between different systems For example System A Master and the back up system B Slave Connect the CP 540 A Master to CP 540 B Slave with the special cable HL540 11 The CP 540 A is synchronized with the Time of Day manually or with GPS The CP 540 B is automatically synchronized by the CP 540 A by choosing Master Slave in the Synchro Menu If the Main system A is disconnected or communication fails the back up system B will operate with its own time of base The Drift DEV described later Synchronization by GPS is also into the mode Thus if the Main System A is again operational it will take its main function as Master if the Drift is lower that 100 usec All information is of course printed How to charge the Docking accumulator The Docking could be charged alone or connected to a CP 540 Charge the docking with the power supply HL 540 1 from the CP 540 Connect the power supply to the POWER connector of the Docking connector 3 poles The LED located at the bottom of the Docking allows you to see the charging status o LED is red during the charge 6
3. el PROFESSIONAL TIMING DOCKING GPS User Manual Version 01 2009 1 General The GPS Docking is equipped with a Li lon accumulator ensuring exceptional autonomy to the Chronoprinter 540 even at very low temperatures 20 C 4 F A satellite detection module GSP ensures the automatic Time of Day synchronisation and precision control Power Output Top Minute Reset Antenna GPS Output Connector Master gt Slave Input System A Master gt Slave System A A ntenna GS Charge LED Connector RESET button in case of a problem with the Docking To RESET press the mini contact located under the identification plate of the Docking Use a small unfolded blunt instrument to gently depress Important recommendation e To guarantee the security of your timekeeping it is necessary to use your CP 540 with the internal batteries in a charged state e Do not forget to charge the Docking before its use see How to charge the Docking e If the system is not used for several days we recommend you to disconnect the Docking from the Chronoprinter and remove the batteries from the CP 540 e Do not forget to replace the red blanking plug into the DOCKING on the CP 540 to protect its connector e Protect the Docking with its original packing IMPORTANT It is essential to update the software inside the CP 540 Docking before initial use You will find the software version on our inter
4. hours for a complete charging o LED is green when the docking is fully charged When the CP 540 is used with the Docking the external power supply should be connected to the CP 540 WARNING The Docking should be not charged with a temperature lower that 0 C 32 F Remark The charging status of the Docking is displayed on the CP540 LCD if charged together If the Docking is too discharged the batteries of the CP 540 will power the system If the power is too low the Time on the LCD will flicked and the printer will print Low battery before to switching OFF automatically When the charge indicator of the Docking shows 50 on the LCD Docking Menu you still have at least 4 hours of autonomy 8 Technical specification General 00000 Accumulator O O O GPS 00000 Operating condition External power supply Top minute output Connector IN OUT Type Charging condition Charging current Precision 20 C to 60 C 12Vdc optocoupler for Master Slave 2 x RJ13 7 4V Li Po 2700mAh 0 to 40 C 500mA 5 5 hours 50 n seconds 50 x 10 9 sec Current consumption when activated 30 mA when GPS is actived 12 channels continuous tracking receiver Connector for external antenna UE TAGHeuer PROFESSIONAL TIMING TAG Heuer PROFESSIONAL TIMING 6A Louis Joseph Chevrolet 2300 la Chaux de Fonds Switzerland Tel 032 919 8000 Fax 032 919 9026 E mail info taghe
5. net site www tagheuer timing com Docking connection e Remove the DOCKING red blanking plug from the CP 540 which gives access to the docking connector e Place the DOCKING red blanking plug on the Docking at the reserved place under the female connector e Place the CP 540 on the DOCKING and press firmly to ensure a good connection 4 How to Use GPS e Carefully connect the GPS antenna cable in the socket 21 in its connector The GPS antenna must be installed in a clear open place outdoor with an unobstructed view of the sky in order to correctly receive the satellite signals generated by the GPS system e Menu GPS ON OFF o Select GPS ON and confirm o Select the time difference between GMT time and your time zone ex GMT 2 in the west of GMT or GMT 2 in the east of GMT o Validate your choice this information is stored in memory o The display shows initially GPS Searching then GPS Active as soon as it locates several satellites o GPS Searching is also printed with the indication GPS UTC Delta 16 sec Then GPS ready for Synchro o Validate 2 times under GSP to make the Synchro mode Synchro The synchronization of Time of the Day with the correct date is automatically made REMARK UTC TIME The time provided by the satellites is GPS terrestrial hours of a certain number of seconds 16 seconds since July 2012 This information is transmitted by satellites every 12 5 mins It remains in the G
6. uer timing com Http www tagheuer timing com
Download Pdf Manuals
Related Search