STORM Drone 4 Flying Platform (V2.0) USER MANUAL
Contents
1. Do not touch anything around 7 10 seconds until transmitter stop flashing and you will see the RX701 receiver have solid light that means binding has completed 8 On the transmitter go to MODEL gt FIXED ID turn it ON then press DN button to confirm the code then press ENT and press ENT again to confirm it will ask you to RUN choose YES and press ENT From now on your receiver is bound to this memory on your DEVO 7 Radio Controller Parameters If you reset your radio controller Devo 7 setting you can apply the setting below 1 2 MODEL gt TYPE gt AERO MODEL gt INPUT gt FM SW INH MODEL gt INPUT gt HLDSW HOLD FUNCTION gt TRVAD gt GEAR 100 100 FUNCTION gt TRVAD gt FLAP U100 D100 FUNCTION gt TRVAD gt GYRO 100 100 3 MODEL gt OUTPUT gt GEAR FMD and ACT FUNCTION gt SUBTR gt ELEV 0 MODEL gt OUTPUT gt FLAP MIX and ACT FUNCTION gt SUBTR gt AILE 0 MODEL gt OUTPUT gt AUX2 AUX2 and ACT FUNCTION gt SUBTR gt THRO 0 4 MODEL gt AMPLI gt 20 FUNCTION gt SUBTR gt RUDD 0 5 FUNCTION gt REVSW gt ELEV NORM FUNCTION gt SUBTR gt GEAR 0 FUNCTION gt REVSW gt AILE NORM FUNCTION gt SUBTR gt FLAP 0 FUNCTION gt REVSW gt THRO NORM FUNCTION gt SUBTR gt GYRO 0 FUNCTION gt REVSW gt RUDD NORM FUNCTION gt SA2. Never discharge batteries to below 3V per cell 9 Remove batteries when not using the drone 2 Copyright 2014 HeliPal com All Rights Reserved Package Includes 3 Copyright 2014 HeliPal com All Rights Reserved Circuit Diagram Motor 3 RX701 Receiver Red LED Behind Motor 4 White LED FRONT Controller CC3D Motor 1 Black Hex Blot Clockwise Unloc Anti Clockwise Lock Training Balls Silver Hex Blot Clockwise Lock od Anti Clockwise Unlock Anti Clockwise Behind Red LED Clockwise Propellers amp Hex Bolt Direction Circuit Diagram FLIGHT MODE FMD UP 0 Beginner Mode MIDDLE Sport Mode DOWN 2 Free Style Mode OG an Oo Forward Tum 2 Turn gt LAO Right Left Right Power Switch Battery Level Mode 2 Left Throttle Mode 1 Right Throttle Standard 4 Copyright 2014 HeliPal com All Rights Reserved Quick Start Procedure 1 Flight Mode FMD UP 0 0 means Beginner Model Easy to control 2 Throttle Down 3 Power On 4 Check Battery Level Mode 2 Transmitter Left Throttle Stick 5 Put it on a horizontal surface 6 Connect Battery and battery level monitor 7 Wait for 10 Seconds until blue LED blinks slowly 8 Throttle Down Rudder Right to unlock the system when you unlock the system propellers will start spinning Please be careful Mode 2 Tra
3. FE gt ELEV HOLD FUNCTION gt REVSW gt GEAR NORM FUNCTION gt SAFE gt AILE HOLD FUNCTION gt REVSW gt FLAP NORM FUNCTION gt SAFE gt THRO SAFE L100 FUNCTION gt REVSW gt GYRO NORM FUNCTION gt SAFE gt RUDD HOLD 6 FUNCTION gt TRVAD gt ELEV U100 D100 FUNCTION gt SAFE gt GEAR HOLD FUNCTION gt TRVAD gt AILE L100 R100 FUNCTION gt SAFE gt FLAP HOLD FUNCTION gt TRVAD gt THRO H100 L100 FUNCTION gt SAFE gt GYRO HOLD FUNCTION gt TRVAD gt RUDD L100 R100 6 Copyright 2014 HeliPal com All Rights Reserved
4. STORM Drone 4 Flying Platform V2 0 USER MANUAL FULLY ASSEMBLED with 2 4Ghz Transmitter included 1 Copyright 2014 HeliPal com All Rights Reserved DISCLAMIER Please read this disclaimer carefully before using this product This product is a hobby with motor but not toy which is not suitable for people under the age of 18 By using this product you hereby agree to this disclaimer and signify that you have read them fully You agreed that you are responsible for your own conduct and content while using this product and for any consequences thereof Before you fly the drone 1 Make sure all connections are good and keep children and animals away during firmware update system calibration parameter setup and the flight 2 Always fly the drone away from unsafe conditions such as obstacles crowds high voltage lines etc 3 Do not use in bad weathers such as rainy day snow windy more than moderate breeze hail lighting tornadoes hurricanes etc 4 Check whether the propellers and the motors are installed correctly and firmly before flight Make sure the rotation direction of each propeller is correct 5 Check whether all parts of the drone are in good condition before flight Do not fly with aging or broken parts 6 Never overcharge LiPo batteries Do not charge above 4 2V per cell When the battery is fully charged disconnect it from the charger 7 Never leave the battery charger unattended during charging 8
5. nsmitter Left Throttle Stick 5 Copyright 2014 HeliPal com All Rights Reserved Lost connection with radio controller Inside the drone there is a RX701 Receiver to connect your radio with controller to control the drone If the LED indicator is flashing RED rapidly then you need to do this re binding step below 1 Make sure you have NOTHING plugged into BATT port on the RX701 receiver 2 On the transmitter select MODEL gt FIXED ID press ENT if it is showing the code then press ENT again press one more time till it is showing RUN press R to choose NO press ENT again it s showing FIXID press R again to choose OFF then press EXT and turn off transmitter 3 Plug the bind plug into Batt port on the RX701 receiver with this plug still in BATT port and power up the drone you will see receiver flashing red slowly then means old code has been erased unplug drone battery and remove this bind plug 4 Now you need to activate the Fixed ID function Turn on transmitter and then make sure Throttle Stick is all the way down all trimming is neutral both corner FMOD switch and Throttle Switch is off pointing backward and all switches on the transmitter pointing upward then turn off transmitter 5 Connect drone battery the receiver will start flashing place drone on flat surface 6 Turn on transmitter you should see black box running on the transmitter screen do not touch anything or you will break the searching mode 7
Download Pdf Manuals
Related Search