Installation & User Manual V2.03
Contents
1. Connections A O U Volt Free Tamper Contacts 1 and 2 Wiring Diagrams W iring Diagrams with Fire Alarm Override 12V Linear Power supply Wired 485 Network 1 Connections l l A O Volt Free Q Tamper Contacts 1 and 2 mg z Door Exit Button g IM if Door Contact M 0V W hen the fire alarm is activated 0V removed from IP3 the door will be opened L Fire Alarm 0V Panel Common OV from the Fire Alarm Panel and the OV from the Door Control to avoid any ground loop issues Wiring Diagrams with Interlock connections 12V Linear Power supply Note Used ONLY for Wired 485 Network Connections A O l l l l 12V IP3 OV IP2 No IP1 com OP1 NC OP2 tte ae FF Wiring Diagrams FRY Door Exit Button g Contact N 0V Interlock OP to N Interlock IP on 42nd Door Olnterlock IP from G Interlock OP on 2nd Door 12V Sounder HN Volt Free Tamper Contacts 1 and 2 Se Controller 1 Configuration y Input and Outputs Number ily Input 2 Door Contact Input 2 Interlock Input ba Interjock Output Door Options E Toggle operation Ant talgate Timed Actions Locked Alarm Options Unlocked oor forced alarm Ml Intruder alarm door Card and pin Inactive Click the Doors Icon on the left hand toolbar Click Add New Door The Door is added to the Controller Configure the required Door2. The Door Control will then start to scan and enrol on a GSD controller Refer to the section Enrolling Door Controls for instructions on how to configure the GSD Windows Software Restoring Factory Settings Wi Pin amp Prox W i Pin 55 Restore Factory Default Settings Example Note The Door Control can not be defaulted while enrolled onto a GSD network pono The Door Control must first be disabled using the GSD windows software If the Door Control is enrolled onto the GSD Network Controller then the Default Engineer code will be set by the GSD windows Software If Engineer Code is lost Ensure the Door Control is disabled using the GSD windows software then remove the Security Caps See page 5 and hold down the X key during power up and enter the default Engineer Code 6666 immediately This will restore the factory settings Restoring Factory Settings Wi Prox Step Description 1 Present Programming Card 2 Times Programming Card x 2 Present Any Card Once Note Add a progrmming card to the Wi Prox Door Control The Door Control must be disabled first if it has been enrolled onto a GSD Network Controller Follow the below method to add a programming card to the Door Control Adding a Programming Card Step Description 1 Remove security caps and power down unit Power up unit and Present Any Card 2 times immediately This card is now the Programming Card for the unit Refit security caps Factor
3. settings Door Timers Alarm Options Door Options Timed Actions Inputs amp Outputs Click Save to transmit the changes to the GSD Controller Note Placing the mouse cursor over a door feature will display a description of the feature Assigning a Door Address on Wireless Network On the Controller screen Click Allow Doors to J oin this Controller All Door Controls that don t have an address start to beep out the next available address The Keys will also illuminate to indicate the address e g Keys 1 amp 5 will be ON for address number 15 1 2 Hit any key on the beeping Door Control to assign this address Present a Card on the beeping Proximity unit to assign this address W hen a Door Control is assigned an address all unassigned Door Controls will start to beep the next available address W hen all doors are assigned Click Secure Network Note While assigning door addresses leave the Controller Screen open or the network will be Secured automatically stopping doors from joining the network Assigning a Door Address on a Wired 485 Network Step Right Click on the Controller Icon select Manually Assign Addresses Follow Step 2 above to complete the process
4. 5 Network N SON j Door Exit Button Volt Free O Tamper Contacts 1 and 2 Sounder HN W iring Diagrams with External IP3 Function as A Note Used ONLY for Wired 485 Network Connections I I I I I 12V Linear Power supply Volt Free YC Tamper Contacts 1 and 2 Sounder Wiring Diagrams WA Card and Pin O Cardor Pin Lock Door Door Contact AN eN JA i H mel 4 es ts te ee ae A 0V Door Exit Button x a Wiring Diagrams EB Wiring Diagrams with W iring Diagrams with Interlock connections Alarm Panel Connections 12V Linear Door Exit Button ve 12V Linear Door Exit Button Pi a Power supply ts Power supply amp Door Contact Contact OV IP2 OV IP1 OV NO IP1 P1 COM on Alarm Panel NE SES Interlock OP to A Interlock IP on c l 9 2nd Door TIT AE mm Olnterlock IP from lt p E lt O ES Ah l Za O Arm Alarm Input 12V P3 gt 1 12V 1P3 I IP2 Interlock OP O I AN G on 2nd Door 12V Note Used ONLY for Wired 485 Networ th Connections nen nn Note Used ONLY for l A O 7 U Volt Free Tamper Contacts 1 and 2 Sounder and the OV from the Door Control to avoid any ground loop issues Only the Manager User can activate deactivate the Alarm Panel W hen the Alarm Panel is activated all other users are locked out u Wired 485 Network Sounder HE
5. Other products from GSD Stand alone products GSO also offers fully functional standalone door controls for less complex g lobal security devices door management This attractive design with modern aesthetics will complement any building 65D Oita Key Dac GSD Proximity Switch 05D Biometric switth ve SOS Features 50 users Access control Door monitoring Manager user fire and intruder alarm interface a i Backlighting E Mult format RFID reader IN Access 712 Tamper resistant FingerPrint 5 Amp relays indoor or outdoor use Robust polycarbonate housing with stainless steel keys Mounts onto a standard electrical back Dox Lli A Puta eels Initial Setup No of doors controlled AP r 12v to 24 12v to 24 12 to 24 2 Es Ac or 0C Kae Mu Installation Diagrams ED a 1 i 1 1 1 a ACCESS t 3 1 A Wiring Diagrams KD Enrolling Door Controls EY Wi Pin amp Prox 7 Wi Pin Wi Prox global security devices Technical Specs Power Suppl Current consumption Current consumption with load max Relay Contact Rating Operating Temperature Moisture Resistance Dimensions Flush Mount Surface Mount Number of Users Initial Installation The Door Control should be Factory Defaulted after installation This will restore all Belle settings to the Door Control and will unenrol it from any existing GSD Controller
6. y Default PIN codes The following PIN codes are the Factory Default Settings The Default Engineer code is 6666 User PIN 1111 Note The User PIN 1111 is deactivated when the Door Control is enrolled onto a GSD Network Controller W hen Surface M ounting the Door Control a Surface Mount Collar is required Fix Surface Mount Collar to wall ensure arrow is pointing upwards Surface Mounting After fixing Surface M ount Collar to wall as above and wiring is complete as per wiring diagrams on pages 6 11 the Door Control may then be screwed to Surface M ount Collar using security screws provided Both Security Caps are then clipped onto the Door 9 Control es To attach Security Caps Simply align the tabs into holes and push 1 on until click is heard Security Caps Installation Diagrams Flush Mounting Door Control is mounted to electrical pattress box using security screws provided Both Security Caps are then clipped onto Door Control To attach Security Caps Simply align the tabs into holes and push on until click is heard To release Security Caps push a screwdriver into slots on the side and pull forward Ag Wiring Diagrams W iring Diagrams with External Reader Function 12V Red amp Brown 12V Linear Datal Clock Power supply a Yellow amp White 0V External Data0 Data Reader Door Contact Note Used ONLY for Wired 48
Download Pdf Manuals
Related Search