Home

Allegro Bay Owner`s Manual

1. The bathroom also contains a 12 VDC vent fan which is controlled by an on off switch mounted on the bathroom wall Doors Caution Always secure the dead bolt lock while the motor home is in motion to prevent accidental opening of the entrance door The primary entrance door Figure 13 7 to the motor home is a radius door having a key lock and a dead bolt for additional security There is also a screen door Figure 13 8 associated with the entrance door the screen door will permit increased air circulation when the entrance door is open To enjoy this benefit the screen door is operated independently of the entrance door To protect the contents of the motor home and the very motor home itself it is prudent to lock the motor home when one is to be away for any length of time Both the key lock and the dead W bolt should be used for maximum security of the motor home Figure 13 7 Entrance Figure 13 8 Screen Door Door 136 ROUTINE MAINTENANCE Routine Maintenance 141 ROUTINE MAINTENANCE EXTERIOR CARE Important Damage caused by improperly performed maintenance or inadequate maintenance is not covered by your Tiffin Motorhomes Limited Warranty Washing The exterior Figure 14 1 of your new motor home is made of pre finished fiberglass Frequent washings and thorough cleanings are required to prevent damage to the motor home finish after exposure caused by damaging salts calcium chlor
2. 2003 by Tiffin Motorhomes Inc all rights reserved Printed in the United States of America Fourth U S Printing September 2004 20070531 ALLEGRO BAY OWNER S MANUAL Table of Contents Chapter 1 General Information Delivery 1 2 Dealer Responsibilities 1 2 Customer Responsibilities 1 2 Tiffin Motorhomes Limited Warranty 1 3 Major Equipment Manufacturers 1 3 Warranty Service 1 4 Owner s Information Package 1 5 Customer Relations 1 5 Specification Labels 1 5 Weighing Procedures for the Allegro Bay 1 7 Weight Distribution of the Motor Home 1 7 Chapter 2 Driving Safety Instructions Safety Considerations 2 2 General Warning 2 2 Prior to Departure 2 3 Driving 2 4 Fuels for the Motor Home 2 5 Liquid Propane LP Gas System 2 6 LP Gas Regulator 2 7 LP Distribution System 2 7 Recommended Precautionary Practices 2 8 Fire Safety 2 8 Fire Extinguisher 2 9 Smoke Detector 2 9 Emergency Exit Window 2 10 Parking Procedures 2 10 Towing Hitch 2 10 Chapter 3 Heating Air Conditioning Furnace 3 2 Air Conditioning System 3 3 Thermostatic Controls 3 4 Liquid Propane LP Tank 3 4 LP Tank Filling Practices 3 5 LP Gas Regulator 3 6 CO LP Gas Detector 3 6 Chapter 4 Major Appliances Accessories Refrigerator 4 2 Microwave Convection Oven 4 5 Air Filtration Fan 4 5 Cook Top and Optional Oven 4 5 TELEVISION SYSTEM OPERATION 4 7 ALLEGRO BAY OWNER S MANUAL Television An
3. 419 MAJOR APPLIANCES ACCESSORIES on the exhaust system yourself and do not modify temporarily or permanently the exhaust system at all Should any of these symptoms be experienced in the motor home one should IMMEDIATELY evacuate the motor home and seek medical help Shut down the motor home and do not attempt to operate it again until the source s of the CO are located and fixed The CO LP gas detector digital readout will display carbon monoxide readings from 30 to 999 parts per million PPM of CO in the ambient atmosphere within the motor home Under normal operating conditions in the motor home the display reading should be zero Besides taking CO readings every 30 seconds the CO LP gas detector also will indicate the status of the battery life with a LCD liquid crystal display icon and the operating condition of the sensor on the digital display by means of a beeping sound and a flashing red light The motor home owner should become quite familiar with these digital display readings and check them regularly and frequently The display will also indicate possible sensor malfunctions and low battery voltage conditions i e flashing red light and chirping of alarm In the event of an alarm the following steps should be taken quickly 1 Ifthe alarm signal sounds 4 beeps and flashing or solid red light operate the Test Mute button 2 Immediately move to a source of fresh air either outdoors or by and
4. E r omito attress buttons until the number you desire is displayed Remain still until the change is Remote Control complete When adjustment is complete the Sleep Number will stay lit for five 5 seconds and then the display will turn off If you decide to change your Sleep Number before the firmness adjustment is complete just press any button and the Firmness Control System will stop adjusting Then go to the Sleep Number you want If you don t already have your Sleep Number or would like to experiment with finding a different one follow the directions below 1 Lie down on your Sleep Number Bed in your normal sleep position holding your remote 2 Press and release any button to get the current Sleep Number setting Set the Sleep Number to 50 on the remote 55 CABINETS amp FURNITURE 3 Take time to evaluate your comfort 4 If you like the feel of the mattress at 50 go to step 5 If you find that this setting is too firm or too soft change your Sleep Number in increments of 5 Reevaluate your comfort level after each change Once you have found a Sleep Number setting where you feel comfortable log this number into your Sleep Journal 5 Try to sleep at this Sleep Number for a minimum of five nights It will take your body that long to become accustomed to a new sleep surface After five nights reevaluate your comfort level and log this into your Sleep Journal If you need to make adjustments repeat
5. This section outlines important recommendations to manage moisture in your motor home to avoid moisture related damage such as mold which is caused by moisture The materials and methods used to construct your motor home were selected in part to minimize air leakage and to create a weather tight exterior shell However in order to protect your investment and reduce the risk of moisture related 145 ROUTINE MAINTENANCE damage and costly repairs attention and care has to be taken to manage moisture inside your RV Note These are only suggestions intended to minimize moisture related issues with your motor home If any concerns arise contact Tiffin Motorhomes Service Department at 256 356 0261 Interior Care of Your RV Signs of excessive moisture can be obvious such as water droplets forming on surfaces or wet carpet Conversely signs of excess moisture can be subtle such as condensation forming on metal surfaces When symptoms appear it is important to timely determine the cause of the excess moisture and take appropriate corrective action to prevent moisture related damage Control Relative Humidity Monitoring and controlling relative humidity within the motor home is one of the most important steps to minimize the risk for moisture related damage Ideally relative humidity should be at 60 or less Relative humidity can be monitored utilizing a portable hygrometer Figure 14 4 a small device that measures temperature and r
6. AUTO To set the AUTO position a Manually adjust the motor home to the position desired b Then press the on switch one time to turn the controls off c Press the EXT switch five times d Press the RET switch five times All control panel LED lights will blink on and off e Press the ALL switch three times All the control panel LED lights will turn off f Turn the controls on and simultaneously push the ALL and RET switches 95 EXTERIOR FEATURES RETRACTION MODE 1 Assure that the slide out rooms are fully retracted i e they are in their inboard positions 2 Press the on off switch 29 3 Whether using Manual Controls or the Auto Position Controls simultaneously press both the AL switch and the RET switch and then release those switches The levelers will automatically retract to their fully retracted positions The leveler indicator LED light will blink red during this activity 4 Once the levelers are fully retracted the level indicator LED light green will be on continuously 5 Press the off switch to turn the power off to the control panel NOTE In becoming familiar with the leveling process consult both this Owner s Manual and the specific operating instructions that came with the particular leveling system to gain proficiency Important The leveling system should be cycled once a month or
7. After you have drained the black water tank immediately drain the gray water tank This procedure helps to flush the black water from the sewage hose When both of the tanks are empty flush them with a freshwater rinse before you close the valves The gray tanks are easily flushed by pouring a couple of gallons of water into a sink drain The drain outlet is engineered for quick release of the drain hose adapter Always close the gate valves and secure the end cap to prevent leakage while the motor home is in transit After draining the black water tank it is recommended to add a holding tank deodorant to help control the odor and break down the solids Follow the instructions given on the holding tank deodorant package When using dump stations for draining the holding tanks keep other travelers in mind Please practice good housekeeping Leave the dump stations in good order Above all do not pollute Sewer Connection and Camping When camping at parks with sewer connections it is important to keep the black water holding tank gate valve closed at all times except when dumping The gray water tank can be kept open while hooked to a sewer connection but again the black water tank must be kept closed This is done so that an ample quantity of liquid remains in the black water tank to provide a smooth flow through the gate and drain valves when dumping Sufficient liquid in the tank causes a swirling action that should take any accumulated
8. CD or optional equipment such as the Sirius Satellite Radio external CD changer or auxiliary sources push the Mode button to choose the desired play source Figure 4 15 AM FM CD Stereo System 4 10 MAJOR APPLIANCES ACCESSORIES Sound Settings Volume Rotate the VOLUME knob left or right Bass Treble Balance or Fadet Push the VOLUME knob to scan between the different sound controls Once the desired function is in the display area rotate the knob left or right to achieve the desire level Equalizer Push the EQ button to choose between preset equalizer settings Classic Rock DSP Off digital sound processor off Flat Pop and Jazz as indicated in the display area Mute Push the MUTE button to mute the volume level Press again to return to previous volume level Loudness Push the LOUD button to boost high and low tones at low volume levels Sirius Satellite Radio optional Note If your Sirius tuner is not activated call 1 888 539 747487 SIRIUS to activate The Sirius Tuner ID Number ESN is required during the activation process Follow the instructions below to access the Sirius Tuner ID Number ESN 1 Push the MODE button until SIRIUS appears in the display area Push the TUNE button until DIRECT appears in the display area Wait a few seconds and CH 000 will then appear in the display 3 Push the BAND button and the first 4 digits of the 12 digit Sirius Tuner ID Number ESN w
9. In Dashboard Fuse Blocks Should there be any electrical failure of these components or systems the first troubleshooting procedure should be to check the fuses and have available replacements to replace any blown fuses as may be warranted As an aid to extracting and or installing fuses in the fuse blocks one may wish to buy an inexpensive fuse puller at any electronics or hardware store This useful tool makes the installation or removal of fuses much easiet and prevents inadvertent damage to nearby fuses or the fuse block itself Whenever a fuse has been blown and is to be extracted and replaced it is good practice to examine the wiring going to that particular fuse to see if there is any noticeable degradation e g wiring insulation nicked missing or melted which may indicate damage beyond the fusing proper 79 ELECTRICAL FEATURES Warning Never replace a fuse with a fuse rated larger than that which originally came from the factory To do otherwise will cause serious damage overheating of the wiring and possible ignition of nearby materials resulting in a fire Seven Pin Towing Connector Your Allegro Bay is equipped with a standard 7 pin connector Figure 7 14 near the towing hitch at the rear of the motor home to supply the necessary circuitry to control a towed vehicle Tail Lic Plate The wiring of that and Running EEEN connector is shown in the Lights accompanying diagram 7 Way Round Conn
10. You may wish to keep the completed sheets in a three ring binder for your permanent record 152 MAINTENANCE DATA CHARTS RV Owner Maintenance Record Please enter the following information in the table for your future use Allegro Bay Year Model Tiffin Serial _ O Date Mileage Service Work Performed Performed by Cost Reproduction Master Copy this sheet and use copy to maintain your maintenance records You may wish to keep the completed sheets in a three ring binder for your permanent record 153 MAINTENANCE DATA CHARTS RV Owner Maintenance Record Please enter the following information in the table for your future use Allegro Bay Year Model Tiffin Serial _ O Date Mileage Service Work Performed Performed by Cost Reproduction Master Copy this sheet and use copy to maintain your maintenance records You may wish to keep the completed sheets in a three ring binder for your permanent record MAINTENANCE DATA CHARTS RV Owner Maintenance Record Please enter the following information in the table for your future use Allegro Bay Year Model Tiffin Serial _ O Date Mileage Service Work Performed Performed by Cost Reproduction Master Copy this sheet and use copy to maintain your maintenance records You may wish to keep the completed sheets in a three ring binder for your permanent record 155 MAINTENANCE DATA CHARTS RV Owner
11. _ O Date Mileage Service Work Performed Performed by Cost Reproduction Master Copy this sheet and use copy to maintain your maintenance records You may wish to keep the completed sheets in a three ring binder for your permanent record 159 MAINTENANCE amp DATA CHARTS 15 10
12. e Step 1 Locate the recommended tire pressure on the vehicle s tire information placard certification label or in the ownet s manual e Step 2 Record the tire pressure of all tires e Step 3 If the tire pressure is too high in any of the tires slowly release air by gently pressing on the tire valve stem with the edge of your tire gauge until you get to the correct pressure e Step 4 If the tire pressure is too low note the difference between the measured tire pressure and correct tire pressure These missing pounds of pressure are what you will need to add e Step 5 At a service station add the missing pounds of air pressure to each tire that is under inflated e Step 6 Check all the tires to make sure they have the same air pressure except in cases in which the front and rear tires are supposed to have different amounts of pressure If you have been driving your vehicle and think that a tire is under inflated fill it to the recommended cold inflation pressure indicated on your vehicle s tire information placard of certification label While yout tire may still be slightly under inflated due to the extra pounds of pressure in the warm tite it is safer to drive with air pressure that is slightly lower than the vehicle manufacturer s recommended cold inflation pressure than to drive with a significantly under inflated tire Since this is a temporary fix don t forge tot recheck and adjust the tire s pressure when you can
13. home The A B switcher box is located in the bottom shelf in the passenger overhead cabinet This switch will eliminate the need to manually change the coax cables from the tri pod hookup and the main satellite connection Figure 4 10 A B Switcher Box for Tri Pod Hookup MAJOR APPLIANCES ACCESSORIES Television Sets Your motor home is High Definition HD ready and is capable of receiving channels that are broadcasting in High Definition In order to receive a clear picture from your satellite dish you must install a high definition receiver and subscribe to high definition HD service Your motor home does not feature a manual switching box therefore in order to change from satellite to DVD or TV antenna please follow the directions listed below To Select Audio Video Input o Press the TV Video button on the remote control Select TV to view antenna or cable input To view channels from the TV antenna be sure the antenna booster switch is on It is located in the cabinet on the right above the dash Figure 4 11 Select DBS to view satellite input Select DVD to view main DVD player Figure 4 1 1 Antenna Booster Switch NOTE HD ready satellite receiver must be used for best results To Scan Antenna Cable Channels o Press the MENU button on the remote control o Select SETUP and press OK o Select Program Channel and press OK o Select ANT in o
14. simply follow the directions furnished with the CB radio Note Channel 11 is considered an emergency channel and monitoring this channel may give one information about road conditions accidents and related matters potentially affecting the travels of the motor home operator Figure 4 18 CB Antenna System To talk with someone simply press the push to talk switch and speak To listen to any reply release the push to talk switch and listen to the speaker Remember that communications are one way not two way simultaneously one must talk then allow some listening time for others to talk Consequently it s better to make brief transmissions and allow others to comment rather than making prolonged speeches and possibly not having anyone answer Observe the common courtesies see the owner s manual for more details and acceptable speech Several states have their Highway Patrols monitor the CB frequencies check for exact channels for each state of interest to learn about highway problems and emergencies Be aware of these throughout one s travels in the event that they may be needed Rear View Camera Monitor System The rear view monitoring system Figure 4 19 is provided to aid the driver in backing and parking the motor home A camera mounted on the rear of the vehicle feeds a televised view of the rear of the motor home to the monitor located in the front near the driver Figure 4 19 Rear View C
15. 1419 ROUTINE MAINTENANCE 4 The resulting figure equals the available amount of cargo and luggage capacity For example if the XXX equals 1400 lbs and there will be five 150 Ib passengers in your vehicle the amount of available cargo and luggage capacity is 650 lbs 1400 750 5 x 150 650 lbs 5 Determine the combined weight of luggage and cargo being loaded on the vehicle That weight may not safely exceed the available cargo and luggage capacity calculated in Step 4 6 If your vehicle will be towing a trailer load from your trailer will be transferred to your vehicle Consult this section to determine how this reduces the available cargo and luggage capacity of your vehicle Section Three Glossary of Tire Terminology Accessory weight The combined weight in excess of those standard items which may be replaced of automatic transmission power steering power brakes power windows power seats radio and heater to the extent that these items are available as factory installed equipment whether installed or not Bead Ihe part of the tire that is made of steel wires wrapped or reinforced by ply cords and that is shaped to fit the rim Bead separation This is the breakdown of the bond between components in the bead Bias ply tire A pneumatic tire in which the ply cords that extend to the beads are laid at alternate angles substantially less than 90 degrees to the centerline of the tread Carcass The tir
16. 9 3 Hydraulic Leveling J acks Optional 9 3 Leveling Control System 9 4 Electric Steps 9 6 Mirrors 9 8 Chapter 10 Interior Features Bedspread 10 2 Flooring 10 2 Ceiling 10 3 Window Treatments 10 3 Chapter 11 Plumbing Bath Features FRESH WATER SYSTEM 11 2 Monitor Panel 11 2 Kitchen Sink 11 2 Bath Sink Shower amp Accessories 11 2 Water Pump 11 3 City Water Connection 11 3 Filling the Fresh Water Tank 11 4 Sanitizing 11 5 Water Filter Optional 11 6 Water Heater Bypass System 11 6 Fresh Water Lines 11 6 WASTEWATER SYSTEMS 11 7 General Information 11 7 Toilet 11 7 P Traps 11 8 Black Water Holding Tank 11 9 Gray Water Holding Tank 11 9 Wastewater Disposal 11 9 Sewer Connection and Camping 11 10 No Fuss Flush 11 11 Exterior Shower 11 11 Chapter 12 Construction Features Construction Notes 12 2 Typical Floor Plan 12 2 Chapter 13 Windows Awnings Vents amp Doors Windows 13 2 Awnings 13 2 Vents 13 5 Doors 13 6 ALLEGRO BAY OWNER S MANUAL Chapter 14 Routine Maintenance EXTERIOR CARE Washing Waxing Seals Proper Sealants for Application Striping and Decals Roof Care and Maintenance Moisture Management Tire and Tire Safety Information Tire Pressure INTERIOR CARE Carpet Fabrics Walls and Ceiling Dashboard Woodwork and Floors Countertops Accessories Detectors Condensation 14 2 14 2 14 3 14 3 14 4 14 4 14 5 14 5 14 10 14 2
17. The water pump is now ready for automatic operation The pump will run when a faucet is open and stop when a faucet is closed 7 Never allow the pump to run for long periods of time without water being present in the supply tank as doing so may cause physical damage or blow fuses For no water output when the automatic demand system is used try the following a __SITUAT at Pump running but no water flow Te El Tank p 9 2 Clear the water line to the pump Check the pump switch Check the 12 VDC fuses Check the electrical connections Check the battery All of the water should be drained from the fresh water system when the motor home is not in use for extended periods For more detailed information regarding the water pump one should refer to the water pump manufacturer s brochure in your Allegro Bay Owner s Information Package Pump not running City Water Connection When connecting your motor home to city water be certain to use the water hose manufactured and labeled for potable water service this will assure that the hose selected for use will not alter the taste of the water 11 3 PLUMBING amp BATH FEATURES To connect the city water supply to the motor home connect one end of the hose to the city water supply Figure 11 5 this connection will usually be to a faucet or valve similar to your garden hose valve at home Turn the city water supply on for a few seconds to clear the line Once the hose
18. Treatments Throughout the Allegro Bay the window treatments consist of pleated day night window shades which have two sections Figure 10 4 When closing the shade the first section to become visible is the day section which is translucent and permits outside ambient lighting to come into the closed one encounters the night section which places a heavier more opaque material over the window to block out even more light from the outside The night setting Figure 10 5 is generally used in the evening or when a greater degree of privacy is sought All of the curtains installed in the Allegro Bay are to be dry cleaned only no water based cleaning agents are recommended as they may cause undue shrinking or Figure 10 4 Night top Day bottom fading of the fabric Shade On some windows mini blinds may be installed Instructions for the proper use and cleaning of any mini blinds will be found in the Owner s Information Package furnished with the Allegro Bay Figure 10 5 Night Portion of Shade 103 PLUMBING amp BATH FEATURES Plumbing amp Bath Fixtures 11 1 PLUMBING amp BATH FEATURES FRESH WATER SYSTEM Monitor Panel Figure 11 1 Monitor Panel time a monitor panel Figure 11 1 permits checking the approximate levels in the fresh gray and black water holding tanks the LP gas level and the condition of the house batteries The monitor panel is generally located in
19. button in Figure 4 1 controls the temperature adjustment of both the freezer and the refrigerator compartments the selections chosen will not change if the operation mode AC power or propane gas changes To select the desired degree of coldness push and hold the temp set button this will step through numbers 1 through 9 where 9 the coldest setting attainable Hold the button until the desired setting number is realized then release the button The mode button middle button in Figure 4 1 controls the operation mode of the refrigerator there is one automatic mode and three manual modes of operation To select the desired mode push the mode button and release it when the desired mode e g AU automatic AC AC powered LP propane gas mode DC DC electric In the automatic AU mode the refrigerator automatically selects the most efficient energy source available for operation Should a more efficient energy source become available during the operation of the refrigeration the automatic mode will then select it for continued operation of the refrigerator When 120 VAC power is available it will be selected and the display will show AU AC flashing in the display In about ten seconds the display goes off and only a power indicator light remains on If there is not any 120 VAC power available the display will flash AU LP to indicate that LP gas is the energy sourc
20. climates ambient relative humidity is greater than 60 year round add a dehumidifier drained to exterior to control humidity inside the RV during storage e Refer to other sections of this owner s manual for additional recommendations Modifications to your RV Consult Tiffin Motorhomes for guidance prior to making any modifications to your RV It is important that changes be completed by a qualified service firm to ensure moisture intrusion or accumulation problems do not occur Wet Areas Areas that are exposed to water spills or leaks should be dried as soon as possible and definitely within 24 48 hours Drying areas quickly minimizes the chance for moisture damage and possible mold growth which can begin to form colonies within 48 hours A variety of methods can be used to help the drying process e Remove excess water with an extraction vacuum e Use a dehumidifier to aid drying e Use portable fans to move ait across the surface e Because moisture is key to mold issues treat all signs of condensation and spills seriously and deal with promptly Failure to deal with a moisture issue promptly may cause mote sevete issues where none initially existed or may make a small problem much worse e Learn to recognize signs of mold don t paint over or cover up suspicious discoloration until you are sure it is not mold The affected surface must first be cleaned and dried residual staining may be painted e Be sure to understand an
21. e Prior to starting the motor home engine make sure that all lines e g water sewer and electrical power cords are disconnected and properly stowed e Assure that the leveling jacks are in the travel position e After entering the motor home make sure that the electrically actuated retractable step has properly operated to retract the step fully before starting the engine of the motor home Driving Various adjustments need to be made to assure the driver s comfort and the safety of the motor home before starting and moving the motor home these include e The driver should adjust the driver s seat the tilt steering the exterior rear view mirrors and the instrumentation panel lighting if nighttime for the driver s comfort and safety This is especially important for first time use so that the driver may become accustomed to the feel of the motor home and know where the various adjustments are located before the fact not after some need atises while the motor home is in setvice e The driver should be familiar with all gauges instruments switches and indicators on the instrument panel prior to driving Should the driver encounter any unknowns on the panel they should be investigated via the Owners Manual or Owner s Information Package prior to Figure 2 1 Driver s Side Dashboard amp Instrumentation Console 24 DRIVING amp SAFETY INSTRUCTIONS departure so that the driver fully un
22. for the following 12 VDC circuits All interior and decorative and overhead lighting water heater TV switching box slideouts power roof vents monitor panel and 12 VDC disconnect panel Auxiliary Start Switch a Ba start or emergency start switch Figure 7 2 located on the left side of the dashboard Figure 7 3 briefly connects the Allegro Bay coach batteries to the chassis batteries which in tutn allows the chassis batteries to borrow Figure 7 2 Auxiliary power from the coach Emergency Start Switch batteries to assist in starting the engine If the chassis batteries cannot themselves start the engine in Figure 7 3 Driver s Side Dashboard and Instrumentation the normal mode hold down the battery boost switch eis and retry starting the engine By using the battery boost switch while trying to start the Allegro Bay engine a jump start situation is realized between the coach and chassis batteries If the battery boost switch is required to start the engine on a regular basis have your Tiffin Motorhomes Dealership check the chassis batteries and the associated charging system Battery Inspection and Care As the batteries contain a significant and potentially lethal amount of electrical energy they must be handled with due diligence and care Some of the routine precautions include Warning Remove rings metal watchbands and any other metal jewelry before working around batteries If any metallic o
23. for with furniture polish to sustain the natural beauty and luster of the wood This procedure will also keep the cabinetry looking new prevent the wood from drying and reduce chances of accidental staining or aging Use area rugs and floor mats by the entrance door to trap dirt Use water and damp mop to clean the laminate flooring begin by vacuuming the floor to remove loose dust and dirt Then damp mop the floor with any standard laminate cleaning solution available through retail sales outlets e g Wal Mart Kmart Target or grocery stores The mop should be damp but not dripping To remove candle wax or chewing gum carefully scrape off when the material has hardened For further tips please see the manufacturer s information sheet in your Tiffin Motorhomes Owners Information Package Don t use any abrasives or abrasive cleaners on the laminate flooring Countertops To care properly for the countertops Figure 14 13 in your new motor home always use a heat pad or trivet to protect the surface from hot objects that may t h mar or damage the countertop surface Hot pans and heat producing appliances such as electric skillets when set directly on top of the countertop can possibly mar the beauty and finish of the product Additionally since heat producing appliances can also damage countertop seams it is essential to check with Tiffin Motorhomes to identify seam locations to avoid them during subsequent us
24. hold in place For further instructions to change the dust bag use the attachments and proper cleaning technique refer to the specific Owner s Manual located in your motor home Fabrics The fabrics Figure 14 11 used in this Tiffin motor home for the bedspread draperies headboard and valances contain fire retardant additives that may be damaged by use of improper cleaning products Cleaning instructions for these items are DRY CLEAN ONLY Water based products are not recommended for cleaning the fabrics in your new vehicle Most water based household cleaning products are not formulated for use on these fabrics E Figure 14 11 Typical Fabrics in the Bedroom and may cause excessive shrinkage or fading For best results 1429 ROUTINE MAINTENANCE the fabrics in this vehicle should be cleaned by a professional carpet and upholstery cleaner Spills spots or stains should be treated as soon as possible to avoid permanent damage to the fabrics If a spill occurs blot the fluid with a dry towel do not rub the spill as rubbing may cause the liquid to set in the fabric and cause a stain When attempting to clean a spot or stain always start from the outside and work inward to avoid spreading the stain further Some stains or soils are extremely difficult or impossible to be removed completely These stains should receive immediate professional attention Spills spots stains or soiled areas are the respons
25. in the RV for an extended period Severe Environments Prolonged use of your RV in severe environments for example in extremely cold or hot humid climates will require extra care and maintenance to avoid moisture related issues In both extremely cold and hot humid climates more attention needs to be focused on controlling relative humidity within the RV It also may require the use of a portable dehumidifier to manage relativity humidity within an acceptable range This is discussed further in the Interior Care of Your RV section If you have any questions about moisture related issues in the environment you plan to use the RV in for a majority of the time contact Tiffin Motorhomes Service Department at 256 356 0261 Storage of Your RV During those periods when your motor home is not in use cate must be taken to ensure moisture sources are addressed Ideal storage of your RV would be in an enclosed climate controlled environment When this is not possible the following steps should be taken to ensure moisture is controlled e Turn off all water sources e Turn off all combustion appliances e Drain the water tank s e Drain the water heater e Open all closets cabinet doors and drawers e Close all windows and entrance doors e Open a vent or a window enough to allow for some limited ventilation air flow but not so far as to allow snow or rain to enter 148 ROUTINE MAINTENANCE e When storing the RV in high humidity
26. is Figure 11 9 Sanitation Compartment with installed on the pipe Always drain the tank into an a ie a a and acceptable sewer inlet or dump station never dump tank contents into the environment 119 PLUMBING amp BATH FEATURES Whenever possible drain both the holding tanks prior to traveling The carrying capacity of your motor home will be reduced if water is left in the black or gray tanks each gallon of water transported adds about 8 3 additional pounds to the weight of the motor home The holding tanks should only be drained when they are at least 3 4 full Doing this will provide a sufficient volume of water to allow the complete flushing of waste materials in the drain lines and hose If the tanks are not 3 4 full add enough water to allow for sufficient flushing To empty the wastewater tanks connect the adapter supplied with your motor home to the drain hose If the adapter is lost or broken another one can readily be purchased from any RV supply store Once you have placed the adapter on the drain hose it can remain there for the life of the hose One end of the hose threads up through the hole in the bottom of the service compartment and the other end of the hose feeds into the sewer at the dump station Unscrew the cap from the drain Connect the hose with the adapter in place to the drain fitting Open the gate valve completely by pulling on the T handle The tank will start to drain as soon as the T handle is pulled
27. manufactured with a fiberglass roof Proper care and routine maintenance of your roof will assute many years of trouble free performance Please see Chapter 14 for details on recommended cleaning instructions On the Allegro Bay a roof ladder Figure 9 4 may also be included as an additional feature The ladder load limit 200 pounds is typically used to permit easy access to the roof for routine maintenance and periodic inspections The ladder may be hinged so that its lower half can be folded up onto the upper half when the motor home is in transit When folding up that ladder and securing it be sure that the ball lock pin is securely fastened through the locking device to FF secure the ladder Figure 9 4 Ladder Warning Do not exceed the maximum rating of the ladder i e 200 pound load limit Do not attempt to walk on the roof either while it is wet or when condensation is present from the air conditioning system as that surface would be quite slippery Hydraulic Leveling J acks Optional The following should be done prior to operating the leveling system Park the motor home on a reasonably level site free from obstructions and debris Warn near by personnel of the intended activity Put the motor home transmission in park and engage the motor home parking brake Turn the motor home engine off Don t extend any slide outs until the motor home is level Warning If the vehicle is equipped with a slide
28. must be available either from an external power line connection or from the onboard electrical generator For specific information regarding the use of the washer or the dryer consult the owner s manuals found in the Owner s Information Package Figure 4 20 Optional Carbon Monoxide LP Gas Detector Washer amp Dryer To protect the driver and other occupants of the motor home the Allegro Bay is equipped with a carbon monoxide liquid propane gas detector Figure 4 21 Carbon monoxide CO is a colorless odorless tasteless gas which when breathed bonds to the hemoglobin in the red blood cells and thus drastically reduces or 4 18 MAJOR APPLIANCES ACCESSORIES blocks the transfer of oxygen from the lungs to the rest of the body In sufficient concentrations CO kills by asphyxiation In lesser amounts CO makes the victim groggy lethargic and unable to think clearly or quickly CO is one of the products of combustion for many materials including petroleum based products e g gasoline diesel fuel propane butane among others Since many of the appliances and the engines associated with the motor home produce CO in their normal operations it is necessaty to assure that CO levels do not rise to dangerous levels within the motor home In sufficiently high concentrations CO can kill in minutes Figure 4 21 Carbon Monoxide LP Gas Detector Warning Carbon monoxide gas derived from products of combustion of gaso
29. nine volt battery operated detector The CO LP gas detector uses three AA batteries for its operation The batteries in the smoke and CO LP gas detectors need to be tested periodically and replaced when necessary usually semiannually When cleaning the case on any of the detectors use a damp cloth or paper towel Do not spray cleaners or wax directly into the case as this action may cause false alarms or hinder the normal operation of the detectors An inexpensive battery tester available from any local electronics retailer would be a good investment to make This tester would allow checking of the batteries in the various alarms any flashlights used in the motor home and batteries in other appliances e g portable radios MP3 players CD players PDAs and various electronic games which may be in the motor home during travels Condensation Important Since surface condensation within the motor home cannot be controlled by the manufacturer damage caused by condensation is not covered by the Tiffin 1432 ROUTINE MAINTENANCE Motorhomes Limited Warranty Damage may occur to your vehicle if excessive condensation exists Accumulation of condensation on surfaces within your motor home occurs when warm moist air contacts a cool surface It is most evident on the inside of windows but this problem can be controlled by the following procedure 1 Slightly open a window or roof vent to allow the moisture to escape from the m
30. obtain a cold reading Tire Size To maintain tire safety purchase new tires that are the same size as the vehicle s original tires or another size recommended by the manufacturer Look at the tite information placard the owner s manual or the 1412 ROUTINE MAINTENANCE sidewall of the tire you are replacing to find this information If you have any doubt about the correct size to choose consult with the tire dealer Tire Tread The tire tread provides the gripping action and traction that prevent your vehicle from slipping or sliding especially when the road is wet or icy In general tires are not safe and should be replaced when the tread is worn down to 1 16 of an inch Tires have built in tread wear indicators that let you know when it is time to replace your tires These indicators are raised sections spaced intermittently in the bottom of the tread grooves When they appear even with the outside of the tread it is time to replace your tires Another method for checking tread depth is to place a penny in the tread with Lincoln s head upside down and facing you If you can see the top of Lincoln s head you are ready for new tires Tire Balance and Wheel Alignment To avoid vibration or shaking of the vehicle when a tire rotates the tire must be properly balanced This balance is achieved by positioning weights on the wheel to counterbalance heavy spots on the wheel and tire assembly A wheel alignment adjusts the an
31. of and possible rupture of the water tank Since there is not an automatic shut off when filling the freshwater tank check the level from the monitor panel while filling the freshwater tank on the motor home The excess water should be vented onto the ground from an overflow pipe installed in the vent pipe when the capacity of that 114 PLUMBING amp BATH FEATURES tank has been reached This pipe is installed in the freshwater tank to prevent possible tank rupture from inadvertent overfilling All of the water should be drained from the freshwater system when the motor home is not in use for an extended period of time Sanitizing To assure complete disinfecting of the freshwater system it is recommended that the following procedure be performed on a new system on one that has not been used for a length of time or one that may have become contaminated This procedure is also recommended before long periods of storage such as during the winter months 1 Drain the freshwater tank by opening the drain valves There is one valve for each water tank All of the faucets should be in the closed or off position Prepare a chlorine solution using one gallon of water and one half cup of chlorine bleach 5 sodium hypochlorite solution Prepare enough of the chlorine solution to administer one gallon of solution for every 15 gallons of tank capacity For sanitizing this tank prepare 47 gallons of the chlorine solution This mixtu
32. of the motor home consult your chassis manual for information Fuels for the Motor home Your motor home is designed to have several types of petroleum derived fuels used in the routine operation of the motor home these require prudent and safe handling to assure safety of the motor home and its occupants namely Anytime the motor fuel Le gasoline or diesel depending on what the required model s fuel see Figure 2 2 or the LP tank is to be filled the motor home engine is to be turned off all pilot lights must be extinguished and appliances turned off Further during any filling operation or connecting disconnecting of any LP tanks a NO SMOKING policy should always be observed In a similar manner any other compatable devices of the motor home users e g butane camp lights propane lights Figure 2 2 and grills should be treated in a similar manner to assure the safety of all concerned Gas Tank Warning Liquid Propane LP gas containers gasoline or other flammable liquids are not to be placed or stored inside the motor home because a fire or explosion may occur LP gas containers are equipped with safety valves that may relieve Figure 2 3 Liquid Propane Tank 25 DRIVING amp SAFETY INSTRUCTIONS excess pressure by discharging gas into the atmosphere any containment of that vented LP gas constitutes an explosive hazard e NEVER use an open flame to test for LP gas leaks or to examine the fluid level
33. on the back of the Sirius Satellite Radio Tuner Box If your motor home is equipped with the optional tuner box you will find a green bar code label with the identification number Figure 4 16 in the owners information Figure 4 16 Sirius Satellite package Your motor home has a factory installed satellite antenna Identification Label standard but it may not have the optional tuner box If you wish to purchase the subscription but do not have the tuner box you may purchase the tuner box from Magnadyne All necessary cabling and antennas ate preinstalled If you have any questions concerning the Sirius satellite option you may contact Magnadyne Customer Care direct at 1 800 638 3600 SIR DLP2500 auwe Cable amp Telephone J ack The Allegro Bay contains an exterior cable jack and also a telephone hookup Figure 4 17 This telephone connection permits the owner to access external telephone services e g RV parks so that these services are available for use within the motor home proper Within the motor home there are several Figure 4 17 Cable amp Telephone Jack 4 13 MAJOR APPLIANCES ACCESSORIES telephone jacks e g living room for connecting telephone s as desired Water Heater Warning DO NOT APPLY 120 VAC POWER to or LIGHT the water heater until after the water heater is filled with water and the water lines and heater tank are purged of any trapped air Failure to do so will damage the water heater a
34. outside showers turning on both the hot and the cold water valves and flushing the toilet until the antifreeze solution is flushed out of the system and the water flow is clear Once the system has been flushed open the water heater supply valve and close the water heater bypass valve Open the freshwater tank supply valve from the pump and the icemaker valve Reinstall the optional water filter if used Be sute to close the fresh water tank drain valves to allow the tank to fill Washer Dryer Optional 1 Ze Flush the water pipes Reconnect the water inlet hoses to the corresponding hot and cold faucets then turn on both water faucets Plug in the washer dryer and or reconnect the power Run the washer through the Express cycle with 2 tablespoon of powder detergent or liquid equivalent to clean out the antifreeze This completes the process 14 38 MAINTENANCE amp DATA CHARTS Chapter Maintenance amp Data Charts 151 MAINTENANCE DATA CHARTS RV Owner Data Sheet Please enter the following information in the table for your future use Allegro Bay Year Model Tiffin Serial Appliance Model Number Serial Number Refrigerator Air Conditioner Water Heater Microwave Convection Electrical Generator Television Front Television Rear AM FM CD Stereo Home Entertainment Reproduction Master Copy this sheet and use copy to maintain your maintenance records
35. right until the desired radio station appears in the display Scan Tuning 1 Push the TUNE knob to scan every 5 seconds for a different radio station To stop scanning push the TUNE knob again Seek Tuning 1 Rotate the TUNE knob left or right then release to seek for a different radio station Weather Band Push the W BND button for instant weather band operation NOTE Push the MODE button to return to playback of other sources Programming AM FM Stations Select a radio station then select a button 1 2 3 4 or 5 and push and hold until it beeps The radio station is now programmed to that button Recalling Programmed Radio Stations Push button 1 2 3 4 or 5 to recall a pre programmed station Clock Settings Display Button Push and hold the DISP button until the clock is flashing in the display Adjusting the Minutes Rotate the TUNE knob to the Left to adjust the Minutes Adjusting the Hours Rotate the TUNE knob to the Right to adjust the Hours Note the AM PM indicator NOTE When correct time displays wait a few seconds to allow the time to program CD Operation Playing a CD Insert a CD label side up into the CD slot The CD will auto load and start playing NOTE If a CD does not auto load DO NOT FORCE into the slot as you may already have a CD loaded CD Track Selection Rotate the TUNE knob left or right to change the track 4 12 MAJOR APPLIANCES ACCESSORIES Ejecting a CD Push the
36. scales and only the rear wheels remain on the scales this provides the total weight of the motor home save for the front axle This weight should not exceed the total rating of the axles remaining on the scales The front axle weight is determined by subtracting the weight from the GVW that was obtained in the first step which was performed earlier The result should not exceed the listed front axle weight rating For a more thorough weighing of the motor home Chapter 14 contains more specific axle weight determinations Weight Distribution Throughout the Motor Home To assure the maximum stability of the motor home under static 1 e parked and dynamic 1 e moving conditions the distribution of the items to be carried and stored within the motor home and in the storage bays underneath the motor home should be performed in such a manner to strive for reasonably even side to side and front to rear dispersion of the entire weight of both the stored items and also the driver and expected passenger s during transit This process will assure that the motor home is not lop sided in weight distribution i e all the stored weight on one side and or mainly towards the front or the reat keeping a center of mass of the motor home essentially centered on a front to rear and side to side basis will also provide better control of the motor home when it is in motion 17 DRIVING amp SAFETY INSTRUCTIONS Chapter Driving amp Safety Instr
37. solid wastes with it Accumulation of solid wastes in the black water tank can be avoided by keeping the gate valve closed when connected to the sewer connection If the valve is open solid wastes may accumulate in the tank which may eventually result in costly repairs 11 10 PLUMBING amp BATH FEATURES Caution The gray water tank valve must be in the open position when operating the optional washing machine No Fuss Flush This vehicle may be equipped with a flushing system for the black water holding tank When draining your sewer tank attach a water hose to the sewer spray connection After the tank is drained leave the gate valve open and open the water valve to allow water to spray inside the black water tank this will clean the inside of the tank of any debris that may be left inside the tank After this is done disconnect the freshwater hose and close the gate valve Caution Be sure the gate valve is open when flushing the tank Do not use the same hose for the No Fuss Flush that is used for filling the fresh water tank Exterior Shower Your Allegro Bay has an exterior shower Figure 11 10 for your use and convenience outside That exterior shower is located in the service compartment which is located on the driver s side of the motor home The exterior shower feature allows you to do such things as rinse off sand or grass muddy shoes or bathe yourself outside of your motor home The f
38. steps 4 and 5 If after trying four different Sleep Number settings you have not found your ideal Sleep Number please call Select Comfort s Customer Service at 1 800 318 2231 A trained representative may be able to recommend adjustments make suggestions or pinpoint concerns that might be contributing to less than ideal comfort The cover of your Sleep Number mattress may be spot cleaned with carbonated water or mild detergent DO NOT dry clean the mattress cover or put it in a washing machine Also please DO NOT apply stainguard as it may cause yellowing of the fabric Select Comfort is a leader in the industry in the use of materials designed to inhibit the growth of allergens or microorganisms that in rare circumstances can form inside any mattress bedding pillow or upholstered product Advance antimicrobial safeguards are incorporated into every Sleep Number bed Key components of the mattress have been treated to protect the bed from contaminants such as mold mildew and bacteria growth The unique zip open design of the Sleep Number bed allows you to easily open and view the inside of your bed and ventilate or vacuum if you choose In rare instances under the right conditions mold or mildew can form inside many types of mattresses bedding or upholstered products Should this condition occur in your mattress please contact Select Comfort s Customer Service so they can work with you to return your bed to factory fresh conditio
39. systems The gray water system is for wastewater from the sinks and shower The black water system is for sewage waste from the toilet Each wastewater tank has its own control valve and both drain through a common sewer drain hose Toilet The toilet Figure 11 8 in the Allegro Bay motor home is a plastic one The toilet operates with water from either the fresh water tank with the water pump on or the city water supply Before using the toilet add water to the bottom of the tank Refer to the BLACK WATER TANK instructions elsewhere in this chapter The toilet flushes waste directly into the black water holding tank The toilet uses high velocity water injection to produce swirl effect in the bowl The greatest problem that causes stool solids to accumulate in the holding tank is lack of liquids Figure 11 8 Toilet When using your toilet it is wise to fill the toilet 3 4 full of water this will help wash the solids away from directly below the toilet and to assure complete dumping of 11 7 PLUMBING amp BATH FEATURES the holding tank To add water to the toilet bowl press down on the flush lever until the desired water level is reached To flush the toilet push down on the lever until the water swirls A small amount of water should remain in the bowl The toilet should be cleaned regularly for maximum sanitation and operational efficiency Clean the toilet bowl with a mild bathroom cleaner DO NOT USE CHLORINE
40. the motor home and to assure the proper operation of all factory installed components 2 A customer walk through is performed to familiarize the new customer with the motor home its systems and components and their proper and safe operation 3 Delivery of the Owner s Information Package which contains warranty cards and registrations for the vehicle and all factory installed components from other vendors and suppliers to Tiffin Motorhomes The detailed operation instructions and maintenance instructions on these components are also included in this package 4 Assisting the customer in completing the registration forms to avoid loss of warranty coverage The dealer should review the limited warranty provisions with the customer to stress the importance of completing the warranty cards and registration forms for the components in the motor home to enable the manufacturers to receive them within the prescribed time limits 5 Providing the customer with information regarding warranty and non warranty work on the vehicle and its separately warranted components Customer Responsibilities The customer is responsible for regular and proper maintenance of the motor home Properly maintaining your motor home will prevent conditions arising from neglect that are not covered by your Tiffin Motorhomes limited warranty The maintenance guidelines in this manual and any other applicable manual s should be followed It is your responsibility and oblig
41. the enclosed spaces Sidewalls ate constructed of aluminum or steel framing insulated with 1 2 thick block foam insulation Framing and insulation are laminated between interior d cor board and gelcoat zur fiberglass on the exterior to provide superior strength and rigidity I The insulation provides a sound deadening barrier from outside noises and more effective thermal control of the enclosed cabin in the motor home thus allowing greater efficiency of the heating and air conditioning systems Luan 4 Typical Floor Plan Although there ate many variations of the floor plans for the Allegro Bay a typical floor plan is presented to show the relative components of the Allegro Bay 122 WINDOWS AWNINGS VENTS DOORS Chapter Windows Awnings Vents amp Doors 131 WINDOWS AWNINGS VENTS DOORS Windows The windows Figure 13 1 on the Allegro Bay are of the sliding type Optional double pane windows also provide additional thermal control e insulation to maintain interior temperatures better In the optional double pane windows a dead air space filled with a dry inert gas is sealed between the two panes of glass this dead air space provides additional thermal insulation for the windows and prevents them from fogging internally Additionally there may be a reflective coating on the windows to reflect back a portion of the sunlight to reduce the heating of the m
42. the motor home Cooking appliances require adequate fresh air for safe operation Before using any cooking appliance make sure that an overhead vent or window is open and or turn on an exhaust fan Remember that any LP gas operated appliance in the motor home will be consuming oxygen in the motor home If the motor home is totally closed during such operation the oxygen level may be reduced and the associated carbon monoxide level may be increased thereby causing possible harm or death to the occupants through asphyxiation Always use these appliances with proper ventilation DANGER Notice DANGER IF YOU SMELL GAS YOU SHOULD IMMEDIATELY Extinguish any open flames pilot lights and all smoking materials Do not touch or operate any electrical appliances or switches Immediately shut off the gas supply at the main tank valve or supply connection Open doors windows and other ventilation openings then immediately leave the motor home to allow entrapped LP gas to dissipate Have the LP gas system checked to locate and fix the source s of the leakage TELEVISION SYSTEM OPERATION Television Antenna The Allegro Bay motor home is equipped with a retractable antenna Figure 4 8 for television TV reception of all VHF e channels 2 13 and UHF e channels 14 upwards channels To deploy the antenna for proper reception of TV signals turn the TV antenna crank clockwise CW to raise the antenna this shou
43. then turn on the thermostat in about a minute the furnace should begin to operate and warm or hot air should be coming through the ductwork To shut down the furnace turn the thermostat to the off position Even though the thermostat may be turned off the furnace system will continue to run for about a minute or so to permit a gradual cool down of the heating system which is normal On a regular basis thoroughly clean the complete furnace and air tube passageways to remove dust lint and any other possible obstructions Leak test the entire LP gas system at least semi annually Also check and clean the air blower system annually 32 HEATING amp AIR CONDITIONING Any access hatches to the furnace are for authorized service personnel only as there are no user serviceable parts on the furnace Accordingly do not attempt to tamper with the interior of the furnace Warning Be cautious when washing the exterior of the motor home water should never be sprayed directly into the furnace vent Should any water be forced beyond the rain baffles into the furnace vent the furnace may rust which in turn may cause improper combustion and produce unwanted by products of combustion Before the beginning of each travel season the furnace should be thoroughly cleaned and inspected Any obstructions debris or lint which may obstruct free air flow or impede the operation of the air citculation system should be removed
44. turned off or the thermostat loses power 1 e power failure the air conditioning system will resume operation at the last settings programmed into it when electrical power is restored Liquid Propane LP Tank The Allegro Bay is equipped with an ASME American Society of Mechanical Engineers approved LP tank Figure 3 4 which is equipped with an automatic pressure regulator This tank contains liquid HEATING amp AIR CONDITIONING propane fuel under high pressure As this fuel passes through the main valve and through the regulator it is converted into a gas and its pressure is reduced to a safe level for use within the motor home A LP gas distribution system distributes the gas to those appliances using such in the motor home The heart of this LP gas distribution system is the regulator and that regulator should only be adjusted by a qualified service technician Most of the problems encountered in lighting the pilots of these appliances are caused by regulator mis adjustments The major component of the LP gas supply is a manifold pipe which runs lengthwise underneath the motor home floor From this manifold the various gas appliances ate connected by copper tubing with flared fittings so that connections and disconnections can readily be made as needed Should any of the secondary tubing develop a leak either on the tubing proper or at the fittings do not attempt to splice any of these lines Instead have a qualifi
45. water levels of the batteries e Visually inspect the fire extinguisher s Every Three Months e Check LP gas lines for leaks with soap solution or leak detector e Clean the microwave hood exhaust fan filter and blades e Test smoke alarm carbon monoxide detector and CO LP gas detector e Check operation of windows latches and hinges e Clean the roof clean the roof ducted air conditioner filter or filters e Clean and inspect door and window seals reseal where necessary e Inspect and reseal around the tub and shower area where necessary e Lubricate the exterior door hinges and latches with a graphite silicone lubricant e Check clean and tighten battery cables and inspect batteries for proper fluid levels Every Six Months e Inspect the slide out for proper seal If realignment is necessary please contact an authorized Tiffin Motorhomes Service Center e Inspect all exterior rubber seals apply a UV inhibitor e g 303 Protectant as needed e Change the battery in the smoke detector e Rotate tires as recommended by the tire manufacturer e Check all gas appliances for proper operation e Have the LP system inspected by a qualified technician e Lubricate the movable parts on the entrance step e Change the batteries in both the smoke detector and the CO LP gas detector Annually e Inspection of roof seams and joints should be performed by an authorized Motorhomes Service Center If resealing is necessary
46. 1930 2060 2050 2310 zum S 55 60 65 70 T 80 85 specified speed of the motor home In this al TE as Fa es 00 23 E E E D_47 EL manner one can determine the appropriate cara aan a dae eaa as na ns REE D 4645 4910 5180 5440 5720 6000 6230 6490 6830 inflation pressures for each of the tires on the zos r PES To e as e os XRV LRF Lbs S 3340 3440 3540 3640 3740_ 3890 4030 motor home as a function of the loads they are aut Le tete ate He eHe s a Bm XRV f 3540 to carry on the trip s the motor home is to take wo um i eo T io a0 e nore 5 fao Whenever there is a significant change in the G PSI 75 80 85 90 95 100 LRG Los S 3595 3815 4035 4280 4545 4675 D 6790 7190 7630 8070 8555 8820 235 80R 22 5 XRV loading regimen of the motor home it would be wise to re calculate the load weights of the tires to assure optimal use of the motor home Figure 14 8 Typical Motor Home Tire Inflation Pressures 1426 ROUTINE MAINTENANCE Frequency of Checking Tire Inflation Pressures When one has determined the correct tire inflation pressures for each of the motor home tires as a function of the fully loaded condition of course and inflated the tires under cold i e tires haven t been driven for more than one mile conditions then the air pressures in the tires should be periodically checke
47. 3 14 28 14 28 14 29 14 30 14 30 14 31 14 31 14 32 14 32 14 32 ROUTINE MAINTENANCE SCHEDULES 14 33 Monthly Every Three Months Every Six Months Annually Winterizing De Winterizing 14 34 14 34 14 34 14 34 14 35 14 37 Chapter 15 Maintenance amp Data Charts Motor Home Owner s Data Sheet Motor Home Maintenance Record Motor Home Maintenance Record Motor Home Maintenance Record Motor Home Maintenance Record Motor Home Maintenance Record Motor Home Maintenance Record Motor Home Maintenance Record Chapter GENERAL INFORMATION GENERAL INFORMATION TIFFIN MOTORHOMES WHEREVER YOU GO WE GO Delivery Throughout the entire manufacturing process your Tiffin motor home has been regularly inspected by our qualified personnel to assure you of the finest product of the highest quality without exception However the final inspection at our factory is not to be the last one The pre delivery inspection and system check that your dealer performs ate the final inspections done to your particular motor home prior to your actually receiving your new Allegro Bay motor home Your dealer is also available to assist you in understanding the warranties and completing the necessary forms to activate the warranties for the various appliances and accessories installed in your motor home Dealer Responsibilities 1 A pre delivery inspection and systems check is performed to assure a thorough inspection of
48. A see the Weather Pro Power Awning Diagnostic Service Manual Dometic Corporation for illustration While one person holds the pull strap remove the bolt in the top of the right top casting see picture in the awning owner s manual for details The FRTA will retract 1 e roll in once the bolt is removed Walk the awning to its retracted position i e fully closed When the awning is fully retracted replace the bolt to prevent the awning from accidentally opening during travel NOTE After this procedure has been performed have the awning serviced by a Dometic Service Center or a qualified service technician before any further attempts are made to open the awning The manual patio awning is standard on the Allegro Bay Use the following directions to operate the manual awning properly Extending the Awning 1 Loosen the black adjustment lock knob on either side of the main arm of the awning Flip the travel lock latches upwards By using the pull rod provided with the awning reach up and pull the locking lever forward to release the awning Hook the rod unto the loop of the pull strap and pull Figure 13 5 Awning Fully Retracted Position the awning all the way out to its fully extended position Slide one rafter arm up until that arm snaps into place Push down on the main arm to remove any slack that may remain in the fabric of the awning then tighten the black adjustment knob Repeat this proce
49. Allegro Bay Owner s Manual Tiffin Motorhomes Inc 105 2 Street NW Red Bay AL 35582 U S A Phone 256 356 8661 E Mail info tiffinmotorhomes com 20070531 ALLEGRO BAY OWNER S MANUAL Volume A TIFFIN MOTORHOMES INC 105 2 Street NW Red Bay Alabama 35582 U S A Allegro Bay Owner s Manual ALLEGRO BAY OWNER S MANUAL TIFFIN MOTORHOMES INC Allegro Bay Owner s Manual O Tiffin Motorhomes Inc 105 24 Street NW Red Bay AL 35582 U S A Telephone 256 356 8661 Facsimile 256 356 8219 E Mail info tiffinmotorhomes com DISCLAIMER Many of the features and appliances described in this manual may or may not be reflected in the actual motor home purchased depending on the options and models selected by the motor home owner All items materials instructions and guidance described in this manual are as accurate as possible at the time of printing However because of Tiffin Motorhomes ongoing and dedicated commitment to excellence improvement of Tiffin s motor homes is a continuing process Consequently Tiffin Motorhomes reserves the right to make substitutions and improvements in its makes and models of motor homes without prior notification Substitutions of comparable or better materials finishes appliances instrumentation and instruction may be made at any time it is deemed prudent to provide the customer with the best possible motor home meeting the customer s requirements Copyright
50. EJECT button to eject a disc Pausing a CD Push the MUTE button to Pause disc press again to resume play CD Changer optional Load CDs Insert the CD magazine into the external CD changer Selecting the External CD Changer Push the MODE button until CDC appears in the display CD Selection Push button 1 or 2 to scroll through the selection of CDs in the CD changer If a CD is not in one of the trays the unit will continue until the next CD is found CD Track Selection Rotate the TUNE knob left or right to change the track Reset Button The radio panel or LCD display may fail to function normally due to the vehicle s battery condition and may require resetting the microprocessor if e The vehicle has been jump started from a dead battery condition e The vehicle battery becomes very low and is quick charged e The vehicle battery is removed and replaced Should this condition occur simply press and release the RESET button on the radio panel using the tip of a ball point pen All station programming should remain but you will have to reset the clock NOTE Your radio has Sirius satellite radio capabilities but this does not mean it is ready for immediate use As an option your radio may be equipped with a preinstalled tuner that will allow you to receive satellite radio after contacting Sirius and purchasing a subscription Activation of the tuner requires the Sirius identification control number located
51. For example accumulated dust or lint could possibly obstruct the orifices for the pilot light or may accumulate on the blower blades and unbalance the operation of the blower Additionally any debris in the ductwork when heated by the furnace could emit unpleasant odors or possibly become a fire hazard Consequently the furnace system including ductwork should be periodically cleaned annually is recommended unless the motor home is subjected to dust levels significantly greater than average in which case more frequent cleaning is recommended The Owner s Information Package provides recommended cleaning tips and procedures when needed a more thorough cleaning should be performed by a qualified service technician Air Conditioning System The factory installed air conditioning system is designed for 120 VAC power supplied either from the external power hookup cord or from the generator Any unnecessary interior heat loading e g exposure to direct sunlight for long periods of time transmittance of sunlight through the windows will work the air conditioning system harder and may compromise the desired results Accordingly if the air conditioning system is to be used park the motor home in a shady location whenever possible and close drapes on those windows exposed to direct sunlight Additionally any heat producing sources e g oven unnecessary lights within the motor home will work against the air conditioning system so strive to
52. GHING YOUR SINGLE AXLE RECREATIONAL VEHICLE RV To Obtain Individual Axle and Gross Vehicle Weights STEP 1d STEP 1b Scale Weight lbs lbs a lbs Step 1a GAW Step 1b GVW Step 1c GAW Step 1d From Owner s lbs lbs lbs lbs Manual GAWR GVWR GAWR Vehicle Weight GCWR GVW To Obtain Individual Wheel Position Weights STEP 2a STEP 2b STEP 2c Casa el One Side lbs lbs lbs Scale Weight Step 2a Step 2b Step 2c Calculate Other Ibs Ibs Ibs Side Weight Step 10 20 Step 1b 2b Step 1c 2c Tire Load Ibs lbs Ibs See Note 1 See Notes 1 amp 2 Inflation psi psi See Note 1 See Note 1 Note 1 From the tire manufacturer s load and inflation tables or the sidewall of the tires mounted on the motor home Note 2 If the motor home has duals read dual capacity from the tire and multiply by 2 two to obtain dual assembly load carrying capacity More detailed information can be found in the manufacturer s literature Figure 14 8 associated with the chassis and or the tires provided with the motor K INFLATION PRESSURES FOR MICHELIN TIRES home For example the following table x al 3 y 3 Load en Pressures an ee illustrates the inflation pressures for Michelin semen Range roots re Single 5 3 Tres Dul D 2 X we E PSI 35 20 45 50 55 60 65 tires as a function of the loads per position for a seso RD u 1920 0770
53. Innerliner separation The parting of the innerliner from cord material in the carcass Intended outboard sidewall The sidewall that contains a white wall bears white lettering or bears manufacturer brand and or model name molding that is higher or deeper than the same molding on the other sidewall of the tire or the outward facing sidewall of an asymmetrical tire that has a particular side that must always face outward when mounted on a vehicle Light truck LT tire A tire designated by its manufacturer as primarily intended for use on lightweight trucks or multipurpose passenger vehicles Load rating The maximum load that a tire is rated to carry for a given inflation pressure Maximum load rating The load rating for a tire at the maximum permissible inflation pressure for that tire Maximum permissible inflation pressure The maximum cold inflation pressure to which a tire may be inflated Maximum loaded vehicle weight The sum of curb weight accessory weight vehicle capacity weight and production options weight Measuring rim The rim on which a tire is fitted for physical dimension requirements Non pneumatic rim A mechanical device which when a non pneumatic tire assembly incorporates a wheel supports the tire and attaches either integrally or separably to the wheel center member and upon which the tite is attached Non pneumatic tire assembly A non pneumatic tire alone or in combination with a wheel
54. Maintenance Record Please enter the following information in the table for your future use Allegro Bay Year Model Tiffin Serial _ O Date Mileage Service Work Performed Performed by Cost Reproduction Master Copy this sheet and use copy to maintain your maintenance records You may wish to keep the completed sheets in a three ring binder for your permanent record 156 MAINTENANCE DATA CHARTS RV Owner Maintenance Record Please enter the following information in the table for your future use Allegro Bay Year Model Tiffin Serial _ O Date Mileage Service Work Performed Performed by Cost Reproduction Master Copy this sheet and use copy to maintain your maintenance records You may wish to keep the completed sheets in a three ring binder for your permanent record 157 MAINTENANCE DATA CHARTS RV Owner Maintenance Record Please enter the following information in the table for your future use Allegro Bay Year Model Tiffin Serial _ O Date Mileage Service Work Performed Performed by Cost Reproduction Master Copy this sheet and use copy to maintain your maintenance records You may wish to keep the completed sheets in a three ring binder for your permanent record 158 MAINTENANCE DATA CHARTS RV Owner Maintenance Record Please enter the following information in the table for your future use Allegro Bay Year Model Tiffin Serial
55. OR CAUSTIC CHEMICALS SUCH AS LAUNDRY BLEACH OR DRAIN OPENING TYPES AS THEY WILL DAMAGE THE SEALS IN THE TOILET AND DUMP VALVES Refer to the toilet manufacturer s owner s manual in your Allegro Bay Owner s Information Package for complete instructions and a detailed troubleshooting guide Caution It is important that you use as much water as possible with each flush This will help prevent tissue and other solids from clogging the holding tank outlet P Traps Each of the sink drains the shower drain and the washing machine drain if so equipped has a water trap P trap to prevent holding tank odors from entering the motor home These traps must have water in them to trap odors When the motor home is in motion the water in these traps may splash out of the sink and shower drains When the motor home is stored the water may evaporate from these traps allowing odors to enter the motor home If this occurs run water from the faucet into the drain thus allowing water to fill the traps again 11 8 PLUMBING amp BATH FEATURES Black Water Holding Tank The black water 1 e sewage holding tank is located directly beneath the toilet Before using the toilet you will need to treat the tank with water that is mixed with an odor controlling chemical These chemicals are readily available at any RV supply store Be careful not to spill the chemicals on your hands clothing or the carpet because such may cause a perm
56. air from escaping from the valve stems Tire Wear Balance and Wheel Alignment In addition to tire inflation considerations the tires should also be periodically examined for other types of normal wear and tear If installed and maintained properly all tires mounted on the motor home should wear in a smooth even pattern If the tires begin to show irregular wear patterns and the motor home alignment is still correct then sometimes just rotating the tires by changing wheel position and rotation of the tires will allow the tires to wear evenly Check with the chassis manufacturer Ford or Workhorse and its literature in the Owner s Information Package for particulars on maintaining proper wheel alignment Tire rotation should include the spare tire optional on some models in the rotation pattern and changing the direction of rotation of the tires Tires can be rotated front to rear and side to side Tire Cleaning Proper cleaning of the tires will assure maximum years of service A soft brush and the normal mild soap should be used to clean the tires Use care in applying any tire dressing product as these contain petroleum derivatives alcohol or silicones which may cause deterioration of the rubber possibly leading 1427 ROUTINE MAINTENANCE to cracking and accelerate the aging process In many instances it isn t the actual dressing itself but the reaction of that product with the antioxidant in the tire Heat can
57. amera Monitoring System 416 MAJOR APPLIANCES ACCESSORIES If the mode switch is in the manual mode the monitor will be on when the ignition switch is turned on If the mode switch is in the automatic mode the monitor will display the picture from the rear mounted camera only when the transmission is in reverse gear To use this system effectively please consult the owner s manual for this system this manual is in the Owner s Information Package Warning Do not view TV or video programs while driving Cleaning and General Maintenance 1 If your Allegro Bay has been parked in direct sunlight resulting in a considerable rise in temperature inside the motor home allow the unit to cool off before operating 2 When the casing becomes soiled clean it with a soft cloth dampened with a mild detergent solution Never use abrasive cleaners or chemical solvents as they might damage the casing Basic Reat View Camera Operation 1 Depress the POWER switch The picture appears on the monitor POWER indicator light up green To turn off the picture press it again to release The monitor becomes standby condition POWER indicator light up red 2 Adjust the VOLUME control 3 Adjust the picture contrast and brightness The DAY NIGHT selector switch should normally be kept in the DAY released position When you view the picture at night or in a tunnel etc depress the switch to make the pictu
58. an A C Saf T Alert CO LP Alarm Sharp Corporation Suburban Manufacturing Co The Dometic Corporation For those wishing mote information 800 646 8557 815 877 5700 248 350 7500 319 556 7730 541 942 3888 800 543 1219 612 574 5944 800 211 7262 800 334 4712 316 832 3400 800 383 0269 800 237 4277 423 775 2131 219 294 2017 www atwoodmobile com www atwoodmobile com www globaldenso com www flexsteel com www kwikee com www norcold com www onanindiana com www panasonic com www powergear com www airxcel com www safetalert com www sharp usa com www suburbanmanufacturing com www dometic com e g locations of authorized subsidiaries the following web site www rvamerica com data s_alist htm should be helpful This site provides complete alphabetic listings of all suppliers and vendors for all contemporary recreational vehicles and motor homes Warranty Service If any warranty service may be required that service needs to be completed during the warranty period basic watranty 12 months or 12 000 miles Tiffin Motorhomes warrants its unitized construction for 10 years and its laminations for 5 years Any service work performed after the expiration of the Tiffin Motorhomes watranties WILL NOT be covered by those warranties Exceptions may be made on an individual basis to this deadline on account of the unavailability of parts and or service appointment time where work is to be performed Howev
59. an overhead cabinet above the passenger s seat To use this monitor simply press the desired status button to obtain a read out of the fresh gray and black water tanks and the present condition of the batteries The empty indicator light will momentarily light when the button is pressed If the tank is full all of the lights will be on Lights are sequentially arranged to indicate fluid levels in approximately third tank increments For example if the tank selected is approximately two thirds full then the indicator lights E for empty 1 3 and 2 3 will all be lit at the same On the right hand side of the monitor panel is the water pump switch The switch controls the power going to the pump and is used to turn that power either on or off There are other water pump switches nearby the sinks in the kitchen and the bathroom to enable convenient use of the water system throughout the motor home Kitchen Sink The kitchen sink Figure 11 2 installed is a double bowl stainless steel sink equipped with two sink covers to provide additional counter space when the sink is not in use The faucet in the kitchen features a single handle control For the sink cleaning care consists of washing only with mild detergents and water polishing Bath Sink Shower amp Accessories The counter top in the bathroom Figure 11 3 is a solid surface When cleaning this surface typical bathroo
60. and special trim Radial ply tire A pneumatic tire in which the ply cords that extend to the beads are laid at substantially 90 degrees to the centerline of the tread Recommended inflation pressure This is the inflation pressure provided by the vehicle manufacturer on the Tire Information label and on the Certification VIN tag Reinforced tire A tire designed to operate at higher loads and at higher inflation pressures than the corresponding standard tire Rim A metal support for a tire or a tire and tube assembly upon which the tire beads are seated Rim diameter This means the nominal diameter of the bead seat Rim size designation This means the tim diameter and width Rim type designation This means the industry of manufacturer s designation for a rim by style or code Rim width This means the nominal distance between rim flanges Section width The linear distance between the exteriors of the sidewalls of an inflated tire excluding elevations due to labeling decoration or protective bands 14 22 ROUTINE MAINTENANCE Sidewall That portion of a tire between the tread and bead Sidewall separation The parting of the rubber compound from the cord material in the sidewall Test rim Ihe rim on which a tire is fitted for testing and may be any rim listed as appropriate for use with that tire Tread That portion of a tire that comes into contact with the road Tread rib A tread section running circumfe
61. and the last four numbers represent the week and year the tire was built For example the numbers 3197 means the 31 week of 1997 The other numbers ate marketing codes used at the manufacturer s discretion This information is used to contact customers if a tire defect requires a recall Tire Ply Composition and Materials Used The number of plies indicates the number of layers of rubber coated fabric in the tire In general the greater the number of plies the more weight a tire can support Tire manufacturers also must indicate the materials in the tite which include steel nylon polyester and others Maximum Load Rating This number indicates the maximum load in kilograms and pounds that can be carried by the tire Maximum Permissible Inflation Pressure This number is the greatest amount of air pressure that should ever be put in the tire under normal driving conditions 1416 ROUTINE MAINTENANCE Additional Information on Light Truck Tires Please refer to diagram below Maximum load Load amp inflation when used as a dual Severe snow Light conditions Maximum load amp inflation when Load inflation used as a single limits Tires for light trucks have other markings besides those found on the sidewalls of passenger tires LT The LT indicates the tire is for light trucks or trailers ST An ST is an indication the tire is for trailer use only Max Load Dual kg lbs at kPa psi Cold This info
62. anent stain Pull the toilet levers forward to allow the chemicals to mix with the toilet water Continue pulling the toilet levers until a depth of at least one inch of solution is directly under the toilet Release the levers and the waste tank is now ready for use Caution Use only approved RV odor controlling chemicals in the holding tanks Products containing ammonia and petroleum will damage the ABS plastic holding tanks and seals Gray Water Holding Tank The gray water holding tank is located in the underbelly of the vehicle It is primarily used for the drainage from the kitchen and bath sinks and the shower No special preparation is needed for the subsequent use of this tank Wastewater Disposal Both of the holding tanks terminate in a valve arrangement Figure 11 9 that permits draining each tank separately or together It is recommended to drain the black water tank first before draining the gray water tank This procedure permits the water from the gray tank to wash the black water residue from the drain lines and hose The valves that open to release the water are called gate valves The blade that closed the opening in the sewer drainpipes is connected to the T handle to release contents of the tank s when pulled The sewer line must be securely capped during self containment use to prevent leakage of waste materials onto the ground or pavement Do not pull the holding tank gate valve open when the protective cap
63. any fire department for information on having an extinguisher recharged in that particular locality DO NOT wait a long time to recharge an empty fire extinguisher you ll never know when it may be needed Should a fire occur inside or around the motor home evacuate the motor home quickly and calmly do not panic In the event of heavy smoke or extensive flames keep low crawl if you must and make your way to the nearest exit door emergency window and leave If the fire involves a fuel source e g motor fuel LP gas consider the probability of an explosion and move sufficiently far away to minimize personal harm If such is available immediately place a call to the local fire department or ask someone nearby to do so to report the fire Consider the cause and the consequences of the fire and the risks associated with possibly fighting the fire yourself before trying to extinguish it DO NOT expose yourself or others to unnecessary danger Figure 2 5 Fire Extinguisher Smoke Detector The Allegro Bay motor home is equipped with a battery operated smoke detector located on the ceiling in the living area of the motor home Read and become familiar with the operation and periodic testing of this En detector The smoke detector should be tested on a weckly basis before each trip and after any period of storage of the motor home If a low battery condition is noted or the alarm chirps to indicate a low battery condition imm
64. ation to return the vehicle to an authorized dealer for repairs and service To assist you in avoiding problems with your motor home it is recommended that you do the following 1 2 GENERAL INFORMATION 1 Read the warranty Go over it thoroughly with your dealer to make sure you understand all the terms and conditions of the warranty 2 Inspect the motor home do not accept delivery until after you have gone through the motor home with the authorized Tiffin Motorhomes dealer Ask questions about anything unfamiliar to you Be sure to review and check each item on that list and make sure that the Tiffin Motorhomes dealership does the same Do not sign the checklist until you have done this completely NOTE Some variations may exist between the sales literature and the actual specifics of your particular Allegro Bay in the areas of measurements weights or quantities Ask the dealer to define all the differences as desired or required 3 Please ask questions about anything you don t fully understand about your Allegro Bay Tiffin Motorhomes is here to serve you and assure that you have all the information necessary for your safe and enjoyable use of your new motor home 4 When you are taking delivery set an appointment for adjustments This appointment should be within two weeks after you accept delivery 5 You are responsible for and expected to use your Allegro Bay in a responsible safe manner Please take the time to familiar
65. aucet operates just as it would in your kitchen or bathroom In addition to the shower itself there is an outside courtesy light to permit Use of these amenities Figure 11 10 Exterior Shower in Sanitation Compartment under low light conditions 11 11 PLUMBING amp BATH FIXTURES 11 12 CONSTRUCTION FEATURES Construction Features 12 1 CONSTRUCTION FEATURES Construction Notes Your Allegro Bay manufactured by Tiffin Motorhomes is constructed of the finest materials available by well experienced craftsmen at the Tiffin Motorhomes manufacturing facilities in Red Bay AL Every cate and concern have been taken throughout the total manufacturing process to assure you of the finest motor home available in the marketplace today The Allegro Bay is built either on a Ford Freightliner or a Workhorse chassis Figure 12 1 The floor decking is constructed of 1 2 OSB board to provide desired rigidity and firmness in the floor of the motor home The floor is insulated with block foam to provide both thermal insulation and sound deadening to keep road surface noises from unduly entering the motor home The motor home roof is also insulated with block foam to Figure 12 1 Typical Chassis provide an adequate barrier to heat loss or gain through the roof In the Allegto Bay each sidewall is manufactured to provide essential Domediibergios an strength and durability and is also insulated to assure the comfort of _ _
66. bject tool jewelry etc contacts the positive battery terminal or any connection made to that terminal AND also contacts the negative terminal or any of its connections a SEVERE ELECTRICAL SHORT will occur which could result in an explosion fire and or personal injury Lead acid batteries contain diluted sulfuric acid which can be dangerous avoid direct contact with any battery fluids Always wear eye protection while servicing batteries 73 ELECTRICAL FEATURES Caution Disconnect the 120 VAC electrical power cord and the negative terminal from the coach batteries BEFORE working on the Allegro Bay electrical system Caution If the Allegro Bay ever requires any welding operations on the frame first disconnect the chassis batteries Failure to do so will destroy all of the chassis computer system When batteries ate not used for extended periods of time they will gradually lose their electrical charge Therefore it is necessary periodically to recharge the batteries to increase the operational lives of the batteries It is also necessary to check the external condition of the batteries on a regular basis Look for cracks in the battery case and cover Check the vent plugs and replace them if they are cracked or broken Keep the battery clean Since accumulations of dirt and acid residue around the battery terminals may provide an electrical path for discharging the battery the area around the terminals should be cleaned p
67. ble liquids and Class C e electrical services these ate typically the most likely types of fires to be expected in motor homes Read and understand the accompanying owner s manual on that extinguisher found in your Owner s Information Package and remember the location of the extinguisher In an emergency you won t have the time or presence of mind to do so then You may wish to purchase other extinguisher s e g for the rear interior around the generator outside etc at your discretion These types of fire extinguishers are pressurized mechanical devices and require that appropriate care be used in their safe storage and use The owner s manual will provide necessary guidance for the proper storage handling and use of the extinguishers Prudent preventive maintenance suggests monthly inspection of any fire extinguisher to assure that it is sufficiently pressurized 1 e the needle on the gauge is in the normal zone and that the mechanical components are not blocked in any way Do not test a fire extinguisher by partially discharging the unit this will cause a loss of pressure and may lodge some fire retardant materials in the valve mechanism and cause the extinguisher to continue to vent slowly down to zero pressure Rather if an extinguisher is ever partially used continue its use until the unit is completely discharged then have the fire extinguisher fully recharged at an appropriate service center one can call
68. cold and 5 Figure 4 3 Dometic Control Panel represents coldest For automatic mode operation press the AES Auto Gas mode selector to the right of the on off switch to turn on the AES Auto lamp just above that switch If 120 VAC is available the AC mode indicator lamp will illuminate to indicate that the 120 VAC is being used If 120 VAC is not available the Gas indicator lamp will illuminate indicating that the control has automatically switched to the GAS mode If the Check indicator lamp center of Dometic control panel illuminates and the Gas mode indicator lamp is off the controls have failed to ignite the burner in the GAS mode GAS operation may be reset by pressing the main power on off button first to the off position and then back to the on position Finally press the temperature selector button to select the desired temperature level in the refrigerator P 8 For operation in the LP Gas mode press the AES Auto Gas mode Figure 4 4 Dometic selector button to turn off the AES Auto lamp The GAS mode Refrigerator indicator lamp will then illuminate to indicate that the refrigerator is now being powered by LP gas Within 45 seconds the burner should be ignited and the unit operating normally However on the initial start up of the refrigerator it may take longer than 45 seconds to allow trapped air to be purged from the LP gas lin
69. compound this problem also INTERIOR CARE Important The fading of upholstery carpet and other interior fabrics is generally caused by excessive sunlight The drapes blinds or other shades should be kept closed when the vehicle is parked for an extended period of time to minimize the fading Normal deterioration of the appearance of such items caused by wear and or exposure to strong lighting is not covered by the Tiffin Motorhomes Limited Warranty Carpet A weekly routine of vacuuming the carpet and fabrics throughout the vehicle is recommended the vacuum system Figure 14 10 has a central connection Figure 14 9 within the motor home wherein a vacuum hose can be connected and the necessary vacuuming performed as desired Doing such will prevent an undue accumulation of dirt which can detract from the appearance of the carpeting and thus shorten its expected life Remember to empty or replace vacuum bags before they become overly full this practice will assure that sufficient vacuuming capability is readily available to handle any and all cleaning situations that may arise In catpet areas that receive the most sunlight keeping Figure 14 9 the curtains closed whenever possible will minimize Vacuum Hose Coupling Figure 14 10 fading Also act quickly when anything is spilled or dropped onto the carpet to Vacuum Cleaner prevent or minimize staining System To connect the cleaning hose raise the wall remote inlet val
70. cular motor home has a Dometic refrigerator with an optional ice maker or not there are some steps to be taken in winterizing the oprional ice maker associated with that refrigerator For the optional ice maker the proper steps to be taken are these 14 36 ROUTINE MAINTENANCE Dometic Refrigerator Ice Maker optional 1 2 ES 10 11 Shut off the water supply to the ice maker Place a shallow pan under the water solenoid valve Remove the inlet fitting to the ice maker water solenoid valve Then drain the water from the supply line Remove the plastic nut and water line from the outlet side of the water solenoid valve Then drain the water from that line Note Do not lose the metal insert from the plastic water line One recommended way to secure this insert is to place it into a zip lock bag seal the bag punch a small hole through the top of the bag above the zip lock insert any type of twist tie e paper coated flexible metal wire through the hole and then secure that bag to the outlet line for safekeeping Connect a source of compressed air up to 20 psig maximum onto the inlet fitting of the water solenoid valve Apply AC power to the solenoid valve for forcing the ice maker mold assembly through several harvest cycles Remove the plastic cover from the mold assembly The bail arm must be in the down or on position Start the harvest cycle with a flat blade screwdriver inserte
71. cutting board on top of the countertop to provide necessaty protection to the countertop Excessive heat may also damage the countertop therefore any pots or pans taken directly from the range or oven should not be placed directly on the countertop rather use trivets or some other form of fireproof heat insulators to hold very hot pots or pans on the countertop All drawers are equipped with metal slides to provide additional load bearing strength for the drawers and to permit effortless opening and closing of those drawers even when they are fully loaded These metal guides have a slight locking action when closed To open those drawers slightly lift up on the drawer handle and then pull the drawer open To close push the drawer closed until it clicks back into place i e the locking action is engaged As this cabinetry is typically of furniture grade quality any commercial furniture polish or cleaner can be used Do not try to soak these wooden surfaces with any water or any other liquid be sure to wipe up spills or residues of any fluids that contact these surfaces to preclude any staining or discoloration of the cabinet surfaces Furniture Kitchen Dining amp Living Room Areas On all the various floor plans of the Allegro Bay either a built in dinette booth Figures 5 3 4 or a free standing table Figure 5 6 is provided This dinette provides additional storage under the seat area of the booth in addition to provid
72. cylinder s and immediately consult an authorized service technician to determine what repairs are necessary Leaks may also be detected by noting the sulfurous odor 1 e rotten eggs associated with LP gas caused by an additive added to the normally odorless LP gas DO NOT search for a leak by using a match or open flame Warning When the motor home is not in use be sure to close the main LP gas valve at the tank When the LP gas tank is to be refilled close the main valve to preclude the chance of the pilot lights possibly igniting fumes from the LP fuel As some LP gas appliances e g refrigerator furnace water heater have Direct Spark Ignition DSI systems it is very important that these appliances be turned off when the LP gas is off The DSI boards will continue to work i e generate an ignition spark even when there is no LP gas available LP Gas Regulator The LP gas regulator is the most critical element of the LP gas distribution system The regulator converts the high pressure LP gas from the tank into a reduced pressure LP gas supply suitable for use in the various appliances in the motor home One should regularly inspect visually the regulator system If any damage or corrosion is noted contact an authorized service technician to inspect and repair or replace the regulator Do not attempt to adjust the regulator yourself the regulator has been pre set at the factory Only a qualified LP service technic
73. d Cleaning Tile and Wood Floors Most floors only require a mild detergent and warm water for cleaning More water on the floor is not always better for cleaning Use a damp cloth to clean on a regular basis rather than wet mopping each time For more information regarding the maintenance of the tile and wood floors see the section entitled Woodwork and Floors Storage and Other Isolated Areas within the RV Storage areas are more difficult to condition since the areas ate isolated from the main body of the RV The surfaces of these areas are more at risk for condensation and surface mold growth To minimize this risk clean storage areas regularly and allow an air space between stored items and the exterior wall to promote air circulation Use of Un Vented Combustion Equipment Un vented combustion equipment such as propane stovetops are a source of moisture within the RV For every gallon of fuel consumed approximately one gallon of water vapor is evaporated into the air Whenever possible operate an exhaust fan in combination with the use of any un vented combustion appliance within the RV Water vapor and other combustion byproducts should be vented to the exterior of the RV The RV owner should strictly follow use and maintenance instructions for safe operation of any combustion equipment particularly un vented equipment Exterior Care of Your RV The exterior shell of the RV is the primary weather and moisture barrie
74. d always be done only when the motor home is leveled If the motor home is not 35 HEATING amp AIR CONDITIONING level the tank may be overfilled 1 e more than 80 of capacity and thus subject the motor home to possible fire or explosion from resultant uncontrolled gas flows LP Gas Regulator As noted earlier the LP gas regulator is the heart of the LP gas distribution system This regulator reduces and controls the pressure of the gas on the outlet end to provide a constant supply of gas at a constant pressure to the gas operated appliances The regulator has a vent to relieve excess pressure on the inlet side of the regulator should excess pressure develop in the gas tank and connecting gas line to that regulator inlet The vent would normally release the excess LP gas to the atmosphere until the over pressurization condition is eliminated This vent should be regularly checked to assure that it is not clogged or obstructed If that vent is blocked from normal operation component or system failures may result If periodic visual inspection indicates any sign of corrosion or degradation contact a qualified service technician to repair the regulator as soon as possible DO NOT operate the LP gas system with any faulty component in place Occasionally the inherent moisture in the LP gas can cause a freeze up of the regulator when the gas passes through the regulator The regulator reduces the high pressure of the gas on its inl
75. d eliminate the source of moisture accumulation as a part of the clean up Otherwise the same issues will simply reoccur e Small amounts of mold should be cleaned as soon as it appears Small areas of mold should be cleaned using a detergent soapy solution or an appropriate RV household cleaner Gloves should be worn during cleaning The cleaned area should then be thoroughly dried Dispose of any sponges or rags used to clean mold 149 ROUTINE MAINTENANCE Tire and Tire Safety Information This portion of the Owner s Manual contains tire safety information as required by 49 CFR 575 6 The National Traffic Safety Administration NHTSA can be contacted at 1 888 327 4236 Their web site is http www safecar gov and their address is NHTSA 400 Seventh St S W Washington D C 20590 Section One The National Traffic Safety NHTSA has published a brochure DOT HS 809 361 that discusses all aspects of Tire Safety as required by CFR 575 6 This brochure is reproduced in part below It can be obtained and downloaded from NHTSA free of charge from the following web site http www nhtsa dot gov cars rules TireSafety ridesonit tires index html Studies of tire safety show that maintaining proper tire pressure observing tire and vehicle load limits not carrying more weight in your vehicle than your tires or vehicle can safely handle avoiding road hazards and inspecting tires for cuts slashes and other irregularities are the mos
76. d into the center of the small gear Turn the gear counterclockwise CCW when the hold switch closes the mold assembly will continue to operate through the harvest cycle During the water fill sequence of the harvest cycle the compressed air will blow out the water trapped in the solenoid valve Repeat the harvest cycle operation Le steps 7 and 8 several times Note Damage to the solenoid valve can occur if the AC power is applied for more than 20 seconds Reconnect and tighten the lines on the water solenoid valve The metal insert must be installed in the plastic water line going to the outlet side of the water solenoid Leave the water supply turned off until temperatures are above 0 F 18 C Dry out the ice maker mold assembly with a soft cloth Place the bail arm in the up off position De Winterizing 1 To de winterize your motor home open both of the low point drains to allow the antifreeze solution to drain from the water system 1437 6 ROUTINE MAINTENANCE Next close the low point drains and connect your motor home to the city water system Put water in the freshwater tank and pump at least one gallon through the water pump to remove the antifreeze from the water pump Keep the water heater supply valve closed and the water heater bypass valves open The supply valve for the freshwater tank from the pump must remain closed As in winterizing open the kitchen faucet bath faucet inside and
77. d loading information In addition this placard will show the vehicle s seating capacity for people and a statement regarding maximum cargo capacity Cargo Capacities For motor homes cargo can be added to the vehicle up to the maximum weight specified on the placard For motorized vehicles the combined weight of passengers and cargo is provided as a single number If fewer people are traveling more cargo can be added If more people are involved the weight of cargo must be reduced In any case remember the total weight of a fully loaded vehicle including passengers can not exceed the stated GVWR For motor homes the water and propane also need to be considered The weight of fully filled propane containers is considered part of the weight of the RV before it is loaded with people or cargo and is not considered part of the disposable cargo load Water however is a cargo weight and is treated as such If there If there is a fresh water storage tank of 100 gallons this tank when filled would weigh about 800 pounds If more cargo or people are being transported water can be off loaded to keep the total amount of cargo added to the vehicle within the limits of the GVWR so as not to overload the vehicle Understanding this flexibility will allow you the owner to make choices that fit your travel and camping needs When loading your cargo be sure it is distributed evenly to prevent overloading front to back and side to side Heavy items s
78. d tite pressure if your tires ate not cold Because tires are designed to be used on more than one type of vehicle tire manufacturers list the maximum permissible inflation pressure on the tire sidewall This number is the greatest amount of air pressure that should ever be put in the tire under normal driving conditions Checking Tire Pressure It is important to check your vehicle s tire pressure at least once a month for the following reasons e Most tires may naturally lose air over time 1411 ROUTINE MAINTENANCE e Tires can lose air suddenly if you drive over a pothole or other object or if you strike the curb when parking e With radial tires it is usually not possible to determine under inflation by visual inspection For convenience purchase a tire pressure gauge to keep in your vehicle Gauges can be purchased at tire dealerships auto supply stores and other retail outlets The recommended tire inflation pressure that vehicle manufacturers provide reflects the proper psi when a tire is cold The term cold does not relate to the outside temperature Rather a cold tire is one that has not been driven on for at least three hours When you drive your tires get warmer causing the air pressure within them to increase Therefore to get an accurate tire pressure reading you must measure tire pressure when the tires are cold or compensate for the extra pressure in warm tires Steps for Maintaining Proper Tire Pressure
79. d to make sure that they retain their proper pressures It is recommended that tire pressures be checked at least once a month every two weeks would be better and before any major trip On long trips the tires should be checked every drive morning On short trips a day or less the tires should be checked before one departs on the trip and again before one returns home Check tire pressures when they are cold that is the tires haven t been driven at all or at most less than one mile before being measured In this manner the tire pressure has not been increased by the heating associated with both tire sidewall and tread flexure associated with traveling If one must check tires that are warm or hot remember that they will necessarily read higher than normal Do not bleed these tires down to the cold pressure readings as they will probably then be underinflated when they are actually cool Don t make any adjustments to tire pressures when the tires are warm or hot if such can be avoided To make these tire pressure measurements it is recommended that one purchase a quality truck tire air gauge which has an angled dual head This type of gauge allows one to check inflation pressures of both the inner dual wheel which has the valve stem pointing towards one and on the outer wheel which has the valve stem pointing away from one Pressure sealing valve caps should always be used to protect the valve stems and prevent
80. de of Allegro Bay end caps ate also gel coated fiberglass To clean these fiberglass surfaces only use warm water and a mild cleanser gently wash with soft cloths Use of stiff bristle brushes or other harsh abrasives may cause scratches in the fiberglass surfaces Please note Tiffin Motorhomes is NOT responsible for the weathering oxidation of gel coated surfaces Lighted storage compartments are located on the exterior S sides of your Allegro Bay These external compartments provide ample additional space for your belongings while you are traveling When stowing materials in these storage compartments try to balance the resultant weight load from front to rear and from side to side this will keep the center of gravity of the motor home essentially unchanged and should not adversely affect the handling characteristics of the motor home when it is in motion Security Lights On the Allegro Bay an exterior security light Figure 9 3 is a standard feature A p light is installed on the passenger side of the coach to help light that side of the Allegro Bay for added protection This light can serve as a porch light when the motor home is parked and the awning is deployed so that various activities e g grilling visiting at dusk and later can be enjoyed by the motor home owners and their guests Figure 9 3 Security Light on Exterior 92 EXTERIOR FEATURES Roof amp Ladder The Allegro Bay is
81. ded AC receptacle Never operate the Allegro Bay if there is an electrical short present as an electrical short may deliver an electrical shock to anyone coming in contact with the exterior of the unit If you should feel even the slightest of electrical shock immediately Figure 7 5 120 VAC Receptacle disconnect the unit from the 120 VAC power source and locate the electrical fault Le 75 ELECTRICAL FEATURES ically it is a break in the groundine circuit y g Do not reconnect the 120 VAC power until after that electrical fault is fixed the grounding circuit must be continuous from the frame to the distribution panel to the power cord and to the earth ground so that electrical shock protection is realized 12 Volt DC VDC Receptacles Your Allegro Bay Motor Home is equipped with a 12 VDC receptacle Figure 7 6 conveniently located on the dashboard or bulkhead i e the round connector with a captive black cover as shown in the figure This 12 VDC receptacle can be used for providing power to various items such as cellular phones or personal computers or portable communications equipment This receptacle is usually found on the bulkhead in front of the passenger s seat so that it is conveniently available to be used by the personnel in the cockpit area Figure 7 6 12VDC Receptacle Ground Fault Circuit Interrupt GFCI Receptacles In the kitchen and bath areas there are 120 VAC GFCI receptacles F
82. derstands these items and their functions One should never adopt a learn as you go philosophy as there ate too many controls and switches to be understood before the motor home is actually used Please take the time to become thoroughly familiar with the entire instrument panel prior to using the motor home on the road Do not operate the cruise control function during any extreme weather situations e g snow ice sleet heavy rain or when road conditions are hazardous icy snowy winding roads city traffic or when a constant speed of the motor home is not possible or if traffic conditions don t warrant such Avoid driving the motor home through any standing water If deep enough such water can wet the brake pads and cause fading of the brakes Le loss of braking power and lead to excessive sliding or pulling to one side or another If one has driven through standing water at the first opportunity safely to do so check the braking action If braking has degraded lightly apply the brakes to allow the brake pads to dry don t use the motor home when the braking function is significantly reduced Know the limits of operation of the motor home Don t try to achieve excessive speeds climb overly steep hills traverse overly long grades attempt to use the motor home as an off the road OTR motor home rapidly switch lanes or rapidly accelerate or decelerate the motor home When in doubt about the handling characteristics
83. diately shut the unit off and call a trained service technician to make necessary repairs as soon as possible The Allegro Bay motor home is equipped with a forced air furnace fueled by LP gas The furnace is controlled by the wall mounted thermostat Figure 3 1 located inside the motor home this thermostat controls both the heating and air conditioning for the motor home In the heating mode the furnace heats air which in turn is circulated through ductwork in the floor of the motor home If any obstruction s block the floor vent s or air return register then the furnace will not function properly Therefore any items stored under the cabinets should be carefully stowed to prevent damaging or crushing the furnace ducting or blocking the warm air return When a furnace is being used for the first time there may be an initial burn off of manufacturing compounds or residues left on the heat exchanger or in the ductwork which could produce odors fumes and possibly some smoke This occurrence is normal and should not cause concern unless it persists for an excessive amount of time Figure 3 1 Thermostat To minimize the after effects of this burn off process the initial use of the furnace should be done with all the doors and windows open to permit normal air circulation to dissipate these possible odors and fumes For routine operation of the furnace set the thermostat to the desired temperature setting and
84. e If the gas doesn t ignite within 45 seconds the CHECK indicator lamp will illuminate and the GAS mode indicator lamp will go out To reset when the CHECK indicator lamp is illuminated press the main power on off button first to turn off the refrigerator then again to turn on the refrigerator again NOTE If successful operation isn t realized after one or two additional tries do not continue attempting to use the GAS mode MAJOR APPLIANCES ACCESSORIES Finally press the temperature selector button to choose the desired level of coldness in the refrigerator After initial start up the thermostatic control should be moved from the coldest setting to the desired temperature range usually 3 the mid point on the scale To turn the refrigerator off press the main power on off button to the off i e UP position this will shut off all DC power to the refrigerator including the interior light Microwave Convection Oven The Allegro Bay contains a mictowave convection oven Figure 4 5 All microwave ovens operate on 120 volt AC electrical power supplied either by the external electrical hookup or by the onboard electrical generator in the motor home Between the power source s and the microwave oven is a surge protector to protect the unit from electrical transients and power surges Touch pad controls on the microwave oven are used for operating the oven i e cooking
85. e The generator is conveniently located on the ee passenger s side of the Allegro Bay and is easily accessible Prior to starting or stopping the generator make sure that all the 120 VAC appliances are turned off After the generator has been started wait until the transfer switch has connected before turning on any of the appliances hei The generator can be started from either the remote start 2 switch located on the dash or directly at the generator Figure 7 8 Electrical Generator itself The hour meter installed on the generator records the number of hours of operation of the generator motor this elapsed time is needed for observing necessary maintenance schedules on the generator Caution Failure to turn off the 120 VAC appliances when starting or stopping the generator may damage the transfer switch and or electrical appliances For more detailed operating instructions of the generator and to determine necessary preventive maintenance schedules and procedures review the manufacturer owner s manual Inverter Converter When the 120 VAC power is not available either from the power cord or the generator the optional inverter converter Figure 7 9 may be used if such is installed in the Allegro Bay The control panel for the inverter converter is located above or near the entrance door xantrex PRO aa When the inverter converter is turned on it 8 ee transforms the 12 VDC
86. e 7 11 Circuit Breakers 78 ELECTRICAL FEATURES accompanying figure Be careful when working around these connections as an accidental electrical short to ground Le momentarily connecting the positive or hot terminal to any part of the chassis can be hazardous and harmful Towards this end don t store in this particular storage compartment anything which may move around in transit and subsequently cause any electrical short circuits or anything that is flammable Fuse Blocks Some of the electrical circuitry within the motor home is protected by various fusing systems Some of these fuse blocks are immediately accessible from the driver s side underneath the dashboard The electrical circuits protected by the under dash fuse block Figure 7 12 include headlights panel light for dashboard tail lights optional jacks turn signals cruise control engine computer accessory fuses heater and dash air conditioning Additionally there is another chassis fuse panel which works in conjunction with the chassis fuse panel and provides comparable protection for the above listed circuits Located beneath the access panel on the dashboard Figure 7 13 are two additional fuse panels these panels protect the following electrical systems mirrors optional satellite jacks camera optional power windows dash trim lighter map light optional power seats and radio Figure 7 12 Fuse Blocks Figure 7 13
87. e being used Should the refrigerator be a three way model and neither 120 VAC nor LP gas is available the display will flash AU DC to indicate that the refrigerator is being powered by a DC energy source the batteries Should there be any improper operation of the refrigerator the display will show various error codes the user should become familiar with those codes in the manufacturer s literature for the refrigerator Manual operation can also be selected by pressing the mode button for the desired type of operation In the LP mode either manual or automatic on initial start up of the refrigerator ignition of the propane gas may not occur for 30 seconds If gas ignition doesn t occur within 30 seconds the gas safety valve in the refrigerator will close Then either the refrigerator selects another mode of operation in the automatic mode or an audible alarm sounds in the manual LP mode which will remain on until the mode switch to cancel that alarm In this case push the on off switch two times to stop and re start the refrigerator then attempt the LP gas ignition process once more If the gas still doesn t ignite check the gas supply line and consult a qualified service technician Should a failure occur the display will indicate various failure codes to help the owner determine what fault or faults may have occurred so that they may be expediently addressed Not all failure codes wil
88. e desired position i e either in or out to activate the desired action of the slide out room and continue to be held down until the desired action is concluded NOTE The rocker switch for the slide out will only operate when the ignition switch is in the on position with the engine running and the park brake engaged Releasing the rocker switch before the slide out is fully extended or retracted will stop the slide out at some intermediate position bi atta sig NOTE The 30 Ampere circuit breakers for the slide outs are mounted on the firewall of the motor home Should they need to be re set one must go to the Figure 8 1 Slide Out firewall to do so Switches Operating Precautions Before the slide out room mechanism is to be used make sure that the motor home is parked and the leveling process has been properly completed Verify that no obstacles e g branches trees telephone poles 82 SLIDE OUT FEATURES power water hookups trash bins and the like are within a five foot space envelope of the slide out room to preclude damaging the slide out room when it is finally deployed Warning Before attempting any extension of the slide out room check outside and make sure that there is at least a five foot clearance around the area where the slide out room will be extended Extending the Slide Out Room 1 All windows in any slide out room must be closed and secured before that slide out r
89. e labels indicate the vehicle manufacturer s information including e Recommended tite size e Recommended tire inflation pressure e Vehicle capacity weight VCW the maximum occupant and cargo weight a vehicle is designed to carry e Front and rear gross axle weight ratings GAWR the maximum weight the axle systems are designed to carry For motor homes Both placards and certification labels are permanently attached to the vehicle door edge door post or glove box door You can also find the recommended tire pressure and load limit for your vehicle in the vehicle owner s manual Understanding Tire Pressure and Load Limits Tire inflation pressure is the level of air in the tire that provides it with load carrying capacity and affects the overall performance of the vehicle The tire inflation pressure is a number that indicates the amount of air pressure measured in pounds per square inch psi a tire requires to be properly inflated You will also find this number on the vehicle information placard expressed in kilopascals kPa which is the metric measure used internationally Vehicle manufacturers determine this number based on the vehicle s design load limit that is the greatest amount of weight a vehicle can safely carry and the vehicle s tire size The proper tire pressure for your vehicle is referred to as the recommended cold inflation pressure As you will read below it is difficult to obtain the recommende
90. e maximum load rating be molded into the sidewall of the tire If one looks at a tire sidewall one may see some typical information such as Max Load Single 3640 Lbs at 85 psi cold Max Load Dual 3415 Lbs at 85 psi cold The maximum load allowed for the size tire and load rating and the minimum cold air inflation pressure needed to carry that stated maximum load are noted on the tire Using less air pressure would reduce the load carrying capacity of the tire The amount of air pressure one needs depends on the weight of the fully loaded motor home Consequently one cannot determine the correct air inflation pressure unless one knows the actual weights of the motor home Weighing the Motor Home Earlier in Chapter 1 the procedures for weighing the motor home wete presented see pp 1 7 and 1 8 These procedures provided the weighing of a nonloaded 1 e not stocked with the possessions and provisions the user would normally have onboard for travel motor home Obviously any additional weight stored onboard inside and underneath the motor home will contribute to the overall weight of the motor home 14 24 ROUTINE MAINTENANCE If not stored uniformly throughout the motor home additional weight of the possessions and provisions of the motor home user will load each axle and each tire differently front to rear and side to side distribution of that additional weight Accordingly it is necessary to weigh the motor home fu
91. e motor home is equipped with a Class 3 5 000 pound towing hitch supporting a tongue weight of 500 pounds and an associated wiring connector The motor home is capable of towing light loads and instructions for such are found in the chassis manufacturer s literature in the Owner s Information Package provided with the Allegro Bay 2 10 DRIVING amp SAFETY INSTRUCTIONS As a towed vehicle being pulled by a motor home represents a greater complexity in driving for the driver e g driving turning backing parking one should not attempt such on the road without first practicing such e g in a vacant lot to master these skills The total weight of the motor home and any vehicle towed by TRES Y ci TEE that motor home must not exceed the Gross Combined 7 i Weight Rating GCWR When the motor home is being weighed remember to account for anticipated occupants and their locations in the motor home Any vehicles to be towed KS by the motor home should have adequate active braking Es The wiring connector provided is a standard seven pin connector see Chapter 7 for specific details on this connector Figure 2 8 Towing Hitch 211 HEATING amp AIR CONDITIONING Chapter Heating amp Air Conditioning 31 HEATING amp AIR CONDITIONING Furnace Warning Never attempt to modify the furnace To do so may cause fire explosion carbon monoxide poisoning or asphyxiation If the furnace is malfunctioning imme
92. e of the motor home Although surfacing may be repaired certain steps should ___ i be taken to protect it Figure 14 13 Countertop in the Kitchen Be sure to use a cutting board rather than cutting directly on the countertop surfaces Although minor scratches and cuts can be repaired a little care will assure that the countertop surfaces will keep looking new for years 1431 ROUTINE MAINTENANCE Avoid using harsh chemicals on the countertop Wipe the countertop with a damp cloth to remove water spots For most dirt and stains wipe with a damp cloth and use soapy water or glass cleaner e g Windex Do not expose the surface to harsh chemicals such as paint remover turpentine nail polish remover or any stove and drain cleansers If these chemicals should come into contact with the countertop surfaces immediately wash off these chemicals using appropriate safety measures to avoid injury Accessories The various metallic light fixtures Figure 14 14 bath accessories and faucets can be cleaned by wiping with a soft damp cloth Washing with warm water will remove dry water spots Do not use cleaners that contain harsh or abrasive chemicals Alcohol or other similar solvents should never be used Figure 14 14 Lighting Fixtures Detectors The CO LP gas detectors are self contained and DO NOT require any maintenance other than normal cleaning and periodic testing The smoke detector installed in the motor home is a
93. e space within these cabinets has been so designed to accommodate the typical sizes and configurations of food supplies e g cereal boxes condiments canned goods bottled liquids normally taken on travel trips Based on Tiffin Motorhomes extensive experience with travel requirements of the seasoned motor home users and from Tiffin Motorhomes own research and development in contemporary cabinet design requirements the resultant cabinets offer the greatest storage capacity possible In the bathroom and bedroom additional cabinets are available for storage of sundries and toiletries specific to these areas 52 CABINETS amp FURNITURE In the kitchen a color coordinated countertop Figure 5 2 is provided on top of the floor mounted cabinets To maintain the appearance of the countertop clean with a damp cloth If spotting occurs clean the countertop with a damp cloth and a mild liquid soap Should some dried on residue still persist let a damp cloth moistened with the liquid cleaner stand directly on top of that residue for 15 30 minutes to loosen the residue then clean that spot accordingly Please note that strong chemicals solvents and cleaners e g oven cleaner may damage the surface so do not use any products not specifically designed for countertop cleaning The countertop may be physically damaged too if proper care is not taken Do not cut anything e g vegetables fruits directly on the countertop rather use a
94. e structure except tread and sidewall rubber which when inflated bears the load Chunking The breaking away of pieces of the tread or sidewall Cold inflation pressure Ihe pressure in the tire before you drive Cord The strands forming the plies in the tire Cord separation The parting of cords from adjacent rubber compounds Cracking Any parting within the tread sidewall or inner liner of the tire extending to cord material CT A pneumatic tire with an inverted flange tire and rim system in which the rim is designed with rim flanges pointed radially inward and the tire is designed to fit on the underside of the rim in a manner that encloses the rim flanges inside the air cavity of the tire Curb weight The weight of a motor vehicle with standard equipment including the maximum capacity of fuel oil and coolant and if so equipped air conditioning and additional weight optional engine 1420 ROUTINE MAINTENANCE Extra load tire A tire designed to operate at higher loads and at higher inflation pressures than the corresponding standard tire Groove The space between two adjacent tread ribs Gross Vehicle Weight Rating GVWR The maximum permissible weight of this fully loaded motorhome Gross Axle Weight Rating GAWR The value specified as the load carrying capacity of a single axle system as measured at the tire ground interfaces Hitch Weight The vertical trailer load supported by the hitch ball
95. e used while the motor home is in motion those seat belts should be worn by all people driver passengers in the motor home at that time e While the motor home is moving lock all seats in the forward facing position to provide maximum safety for the users e While the motor home is moving no one inside should ever stand or kneel on seats e g young children 22 DRIVING amp SAFETY INSTRUCTIONS In the majority of states it is the law that seat belts must be used fastened snugly about the chest and hip areas anytime the motor home is in motion to provide desired protection in the event of a crash Any fire extinguisher s should be inspected on a monthly basis to assure that each extinguisher is properly charged and ready for operation Any smoke and or carbon monoxide CO liquid propane gas LP alarm s should be regularly inspected and tested If being used for the first time the smoke and or CO LP gas alarm should be properly activated and fresh batteries installed before the motor home is placed into service Prior to any trip the smoke and or CO LP gas alarm s should be manually tested to assure their correct operation Immediately replace any defective components e g weak batteries Never sleep in a motor home not having functional smoke and or CO LP gas alarm s Should an alarm or detector fail when in transit a suitable replacement can be purchased at most hardware stores superstores or drug stores While
96. ector Bargman Style Extra Aux Circuit Le Tum rere Make sure that any cable g Signals from the vehicle to be towed is wired correctly to common Electric Brakes mate properly with the 99 Front View Roar view connections shown in the White Common Ground 4 Black Battery Charge connector If in doubt Blue Electric Brakes 5 Red Stop 8 L H Turn Signal Green Tail Lic Plate amp Running Lights 6 Brown Stop amp R H Turn Signal 7 Yellow Extra Aux Terminal about proper wiring have a qualified service technician prepare and install the Figure 7 14 Seven Pin Towing Connector necessary cable to mate with the 7 pin connector on the motor home to assure proper operation subsequently when any vehicle is actually towed by the motor home When the towed vehicle is uncoupled from the motor home and the cable is disconnected from the 7 pin connector be sure to close the spring hinged cover plate on the connector to protect the contact pins from dirt ot debris In a similar manner protect the cable end from similar damage weather or debris one such method could be to place the connector end in a heavy gauge plastic bag e g polypropylene polyethylene etc and secure the bag tightly around the cable with a stout elastic band or tape and then mount the secured cable in a manner to keep it both from mechanical damage and water intrusion When the towed vehicle is again coupled to the motor home via the towing h
97. ed by the burner flame thereby causing a fire or explosion Accordingly please use extreme caution when re fueling the motor home The 12 VDC power supply e g 12 VDC system of the motor home auxiliary battery or converter must be on for the proper operation of the refrigerator For electrical operation of the refrigerator either the external electrical power line must be connected to the motor home or the on board electrical generator must be running to provide the necessary 120 volt AC power To operate the refrigerator in the LP gas mode the main LP gas valve must be open Norcold Refrigerator To start the Norcold refrigerator Figure 4 2 on the control panel Figure 4 1 press the main power on off button right hand button to the on position which starts the refrigerator in the automatic mode When this is done if 120 volt AC is available to the motor home the AC mode indicator light will light and indicate that the AC power is available to the motor home However if the 120 volt AC is not available then the gas mode indicator light will be illuminated indicating that the refrigerator will be operating on the LP gas Figure 4 1 Norcold Control Panel Figure 4 2 Norcold Refrigerator 4 2 MAJOR APPLIANCES ACCESSORIES supply To turn the refrigerator off push the on off button for two seconds to shut down the refrigerator The temp set button left hand
98. ed service technician run a new length of tubing to the appliance of concern and then have that line leak tested before placing Figure 3 4 Liquid Propane Tank it in normal operation again To remove repair or replace any gas operated appliance always close the main gas valve at the LP tank this measure will provide an additional element of safety to prevent gas leakage and possible subsequent explosion hazards However if a gas leak is noted or suspected turn off the main valve and keep the LP gas system off until that system is inspected by a qualified service technician as soon as possible Do not delay in addressing any possible gas leaks with appropriate service because of the inherent hazards to safety Warning When the motor home is not being used the main LP gas valve must be turned off Also turn off the main valve when the LP gas tank is to be refueled to avoid the possibility of ignition of fuel fumes by the pilot lights All gas valves on the gas operated appliances with Direct Spark Ignition DSI should also be in the off position during refueling and or maintenance operations DO NOT store LP motor fuel propane butane or other flammable liquids inside the motor home as these represent avery real fire hazard and possible threat to life LP Tank Filling Practices Any LP gas tank associated with the motor home should never be filled to more than 80 of total capacity filling shoul
99. ediately replace the battery It would be prudent to keep replacement batteries in the motor home for any in transit replacements so that Figure 2 6 Smoke Detector the smoke alarm capability is never compromised DO NOT disable the smoke detector for any transient false alarm e g cooking smoke dusty 29 DRIVING amp SAFETY INSTRUCTIONS furnace tobacco smoke rather ventilate the motor home with fresh air and the alarm will reset Emergency Exit Window In the rear of the motor home there is an emergency exit window in the bedroom this window is designed for an emergency exit when it is not practical to exit by the door also an emergency exit in the front of the motor home This window is readily noticeable by its red handle and the red EXIT label on that window To use this window as an emergency exit lift the handle and push outward on the window As required the window can be closed by pulling the window inwards and then lowering the handle to latch the window back in place When the motor home is to be parked it would be wise to note where this window will be so that this exit won t be blocked e g against a tree pole or wall Figure 2 7 Emergency Exit Parking Procedures To park the motor home in any unfamiliar terrain examine the prospective site for surface irregularities slopes ot inclines and other discontinuities i e stumps rocks external connections for power water sewage and also exa
100. eeze 3 Disconnect the inlet connection to the water pump in the sanitary service compartment under the motor home see Figure Figure 14 15 Winterizing 14 15 Attach the supplied vinyl hose via the plastic coupling Process on the hose to the inlet connection and hand tighten that connection do not ovet tighten 4 Place the other end of the hose into a gallon of freshwater system antifreeze one can refer to the local Tiffin Motorhomes dealer or representative for the freshwater antifreeze formulation for your specific area NOTE Do not use automotive antifreeze use only antifreeze approved for RV applications otherwise damage to the systems being protected may result 5 Turn on the water pump to start the flow of antifreeze Turn on each faucet one at a time and allow pure antifreeze to run through that piping Let about one cup drop into the drains to protect the traps 6 When all the antifreeze is withdrawn from the bottle disconnect the clear vinyl hose from the water pump inlet connection and reconnect the inlet line to the water pump This may require more than one gallon of antifreeze 7 When the winterizing process is completed turn the water pump off and then reconnect the water line Store the vinyl hose for future use 1435 ROUTINE MAINTENANCE 8 Open the water supply valve that controls flow from the pump to the tank to help prevent freezing on that water line Note Rememb
101. elative humidity Hygrometers are available at electronics or building supply stores Use exhaust fans the air conditioner and or a portable dehumidifier to manage moisture inside the RV to maintain relative humidity at 60 or less In cold climates relative humidity may need to be at 35 or less to avoid window condensation issues If the motor home is used the majority of the time in a hot humid climate it may be difficult to keep relative humidity below 60 A dehumidifier will help but is important to check the condensation water collection bucket regularly or discharge the condensation water directly to a Figure 14 4 Portable drain Hygrometer Avoid Drastic Thermostat Setbacks Cooler surface temperatures increase the potential for condensation and surface mold growth To minimize the opportunity for condensation to form on interior surfaces maintain a comfortable temperature in your RV and avoid nighttime setbacks of 10 degrees or more Drastic setbacks that reduce the indoor air temperature quickly can increase the chance for airborne moisture to condense on cool surfaces such as windows If you are away from your RV for an extended number of days it is recommended that you do not set the temperature back without taking other measures to manage relative humidity including operating a dehumidifier with a continuous drain Manage Window Condensation Window condensation issues can be identified by water or ice build up usual
102. ems E Mail Into titin essen O Vehicle Weight VW distribution Model Name 400H Freightliner Serial Number 2405 vear 2002 Proper weighing techniques to be used to weigh the uw ne vn west E me e a Jene vehicle number of sleeping positions multiplied by 154 pounds 70 kilograms Specific definitions for the following terminology PA FERNER GENERAL INFORMATION 105 2 Street NW Red Bay AL 35582 U S A Telephone 256 356 8661 Facsimile 256 356 8219 Motor Home Weight Information Weight Terminology and Definitions GVWR Gross Vehicle Weight Rating is the maximum permissible weight of this fully loaded motorhome SCWR Sleeping Capacity Weight Rating is the manufacturer s designated Cargo Carrying Capacity is equal to GVWR minus each of the following ccc UVW full fresh potable water weight including water heater full LP Gas weight and SCWR GCWR Gross Combination Weight Rating means the maximum allowable loaded weight of this motorhome and any towed trailer or towed vehicle Description Weight Kg Gross Vehicle Weight Rating 14 050 6 386 Fresh water weight of 106 gallons 8 3 Ibs gallon 3 8 Kg gallon 80 gallons 4 2 Ibs gallon 6 persons 154 Ibs person Note Dealer installed equipment and towed vehicle tongue weight will reduce CCC Gross Vehicle Weight Rating GVWR Mr Minus LP Gas This is the maximum p
103. en from the load and inflation tables provided by the tire manufacturer These air pressures may differ from those found on the certification label However they should never exceed the tire limitation for load or air pressure If you discover that your tires cannot support the actual weights the load will need to be lightened Tire Safety Tips Preventing Tire Damage e Slow down if you have to go over a pothole or other object in the road e Do not run over curbs or other foreign objects in the roadway and try not to strike the curb when parking Tire Safety Checklist e Check tire pressure regularly at least once a month including the spare e Inspect tires for uneven wear patterns on the tread cracks foreign objects or other signs of wear or trauma e Remove bits of glass and foreign objects wedged in the tread e Make sure your tire valves have valve caps e Check tire pressure before going on a long trip e Do not overload your vehicle Check the Tire Information and Loading Placard or User s Manual for the maximum recommended load for the vehicle Section Two Steps for Determining Correct Load Limit 1 Locate the statement The combined weight of occupants and cargo should never exceed XXX Ibs on your vehicles placard 2 Determine the combined weight of the driver and passengers that will be riding in your vehicle 3 Subtract the combined weight of the driver and passengers from XXX kilograms or XXX pounds
104. ents and to keep them clean and dry Close the cover on the power box if so equipped to avoid an unintentional disconnection and to keep the contents clean and dry Then switch the main breaker to the on position When properly connected the 120 VAC system provides power to all the 120 VAC circuits and outlets when the main breaker is turned on Circuit Breaker Boxes For the Allegro Bay the 120 VAC and 12 VDC breaker boxes Figure 7 1 are typically located beneath the refrigerator or in the bedroom inside the vehicle or in the storage box 7 outside the vehicle The circuit breakers and associated fuses are installed to protect the electrical system of the Allegro Bay from any overloads Do not attempt to change the electrical circuitry or to add appliances yourself Please consult an authorized Tiffin Motorhomes Dealership or Tiffin Motorhomes Incorporated in Red Bay AL to determine whether any changes you desire are appropriate and acceptable Tiffin Motorhomes qualified staff of electricians can readily determine whether any changes sought e 2 CB radio amateur radio satellite television receiver personal Figure 7 1 Circuit Breaker Box 72 ELECTRICAL FEATURES computer system and the like are possible or not and can advise you on how best to realize these enhancements Please note that the 12VDC fuses and breakers are located in a separate compartment adjoining the 120 VAC breakers Fusing is provided
105. er don t rely on the possibility of an exception please schedule any desired in warranty work before your wartanty expires 14 GENERAL INFORMATION Owner s Information Package The Owner s Information Package Figure 1 1 includes valuable documents about your Allegro Bay and its components and systems The Tiffin Motorhomes Allegro Bay Owner s Manual does not cover every possible detail of equipment standard and or optional installed on or in your vehicle By consulting the booklets and instruction manuals included in the Owner s Information Package you will learn how to operate maintain and troubleshoot these items safely and effectively As with all valuable documentation please keep them in a safe secure place for your later use and consultation When you complete and mail to the respective manufacturer s any warranty guaranty registration card s make a photocopy of both sides of each card prior to mailing and keep the photocopy in your permanent records for your Allegro Bay Motor Home Figure 1 1 Owner s Information Package Customer Relations If you wish to schedule maintenance or service or wish to order parts you should notify your local authorized Tiffin Motorhomes Dealership to set up an appointment If you are unsure of the location of your nearest authorized Tiffin Motorhomes Dealership please access the Tiffin Motorhomes website at www tiffinmotorhomes com and then click on the Dealer Loca
106. er the motor home also has an exterior shower therefore this system must be winterized as well If the motor home is equipped an optional ice maker and or an optional washer dryer the following additional steps should be taken Washer Dryer optional 1 With the washer dryer power in the off position put Y quart of RV type antifreeze in the drum then close the door Turn the Program Selector knob to spin Then turn the power on and let the machine go through the spin cycle for one or two minutes Turn the power off and then unplug the washer dryer or disconnect the power cord Shut off both water faucets and then disconnect the water inlet hoses from the faucets and drain them This completes the process Alternative Washer Dryer Winterization through the Freshwater System 1 If one is currently pumping antifreeze through the freshwater system follow these steps to winterize the washer dryer With the washer dryer power off turn the Wash Temperature knob to Warm Turn the Program Selector knob to Regular Wash located in the Cotton Heavy Duty section of the knob Then turn the power on When you see antifreeze in the drum turn the power off Then advance the Program Selector knob to Spin Turn the power on and allow the drum to spin for about 30 seconds Turn the power off This completes the process Depending on whether your parti
107. eriodically One can use an old toothbrush and a sparse amount of a diluted solution of baking soda sodium bicarbonate and water distilled or de ionized preferred tap water acceptable to clean and neutralize any acidic build up around the battery terminals If there is any foaming on the top of the battery this indicates that acidic residues are being neutralized Rinse the cleaned areas thoroughly with distilled or de ionized water tap water is okay too Avoid getting the baking soda solution into the battery fill plugs to each battery cell this would drastically reduce the effectiveness of the battery by neutralizing the sulfuric acid in the battery cells or worse kill the battery Dry the battery cables and terminals to prevent corrosion to protect those terminals further use a plastic ignition spray on the terminals Do not use grease on the terminals especially on the metal to metal connections as grease may act as an insulator and keep the battery electrical power from entering the cables If the batteries are not going to be used for an extended period of time they should be removed from the Allegro Bay and stored in a warm dry place IT IS STRONGLY RECOMMENDED that this service be performed by a qualified service technician as the process is usually too complicated for the average owner to perform For those who may wish to perform this service themselves the following procedure is described cc Mark the batte
108. ermissible weight of the motor home when it is fully loaded this motorhome WARNING Consult Owners Manual s for specific weighing instructions and towing guidelines including auxiliary brake requirements for any towed trailer or towed vehicle Revision Date 24 June 2002 Unloaded Vehicle Weight UVW This is the weight of the motor home as built at the factory with full fuel engine oil and coolants The UVW does not include cargo fresh water LP gas or any dealer installed accessories Figure 1 3 RVIA Weight Label Cargo Carrying Capacity CCC This is the maximum weight of all occupants including the driver personal belongings food fresh water waste water LP gas tools tongue weight of towed vehicle if any dealer installed accessories and the like The CCC is equal to or less than the GVWR minus the UVW Gross Combination Weight Rating GCWR This is the value specified by the chassis manufacturer as the maximum allowable loaded weight of the motor home with a towed trailer and or vehicle if any Sleeping Capacity Weight Rating SCWR This is the maximum weight capacity of the combined number of persons Le number of people multiplied by 154 pounds per person permitted to sleep within the vehicle Gross Axle Weight Rating GAWR This is the maximum allowable weight for a single axle system as measured at the tire ground interfaces The GAWR conside
109. ery disconnect panel Figure 7 4 is located near the interior step There is a rocker switch on the lower left hand side of the panel which can disconnect the battery when the motor home is to be stored for any appreciable time Pressing this switch downwards disconnects the coach batteries only not the chassis batteries This feature is designed to prevent the coach batteries from being drained during extended storage This switch also disconnects all the 12 VDC circuitry from the batteries thus removing the total electrical load from those batteries with the exception of the LP detector When the Allegro Bay is removed from storage press the switch upwards to reconnect the 12 VDC circuitry to the coach batteries again and the 12 VDC systems are now reactivated Figure 7 4 Battery Disconnect Panel 120 Volt AC VAC Receptacles Your Allegro Bay Motor Home is equipped with several 120 VAC receptacles Figure 7 5 located throughout the interior of the motor home These 120 VAC receptacles are of the three prong variety the third prong being a grounding pin which provides adequate grounding to protect one from any electrical shock For these receptacles to work properly do not use an adapter cheater or extension cord which defeats the function of the grounding pin For the same reason never remove or bend away the ground prong or pin from any three prong AC plug so that it would fit a two prong AC receptacle 1 e an ungroun
110. et side to a reduced pressure on its outlet side by permitting a controlled expansion of the gas through the regulator this gas expansion necessarily cools the gas by means of the Joule Thompson effect and if cooled enough may cause any moisture content to freeze To minimize or negate this possibility always keep the main valve to the LP gas tank closed when the system is not in use When the LP tank is empty keep the main valve closed until re filling is to be performed this process will keep any moisture laden air from back flowing into the gas system and trapping unwanted moisture in the LP gas tank If an empty LP gas tank has been exposed to the atmosphere for an extended time let a qualified service technician purge the tank before its next filling operation Important When a LP gas regulator is installed or re installed the regulator must always be installed with the gas diaphragm vent facing downwards For more information consult the manufacturer s literature in your Owner s Information Package that came with the motor home CO LP Gas Detector Since LP i e liquid propane gas is denser than air the LP gas will naturally settle to the lowest point in an enclosed space in the motor home this would be the floor Because of this fact the CO LP gas detector Figure 3 5 is necessarily mounted close to the floor To activate the LP gas sensor on this 36 HEATING amp AIR CONDITIONING detector for the first ti
111. fecting solution to stand in the system at least four hours Drain the system and flush it with freshwater The water system needs to be flushed with water repeatedly if necessary until there is no chlorine taste or smell left in the system To remove any excessive chlorine taste or odor that might remain prepare a solution of one 115 PLUMBING amp BATH FEATURES quart of vinegar to five gallons of water Rock the tank containing the solution by moving the motor home forward and backward several times to clean the tank then drain that tank and refill with clean water Water Filter Optional This unit may be equipped with an optional water filter Figure 11 6 which must be removed before disinfecting the freshwater system First remove the water filter cartridge The water filter is located in the sanitation compartment on the outside of the motor home The filter will remove chlorine ditt and other matter The filter will also eliminate most phenol or similar odors and tastes while delivering sparkling taste free water for drinking and cooking The filter is not guaranteed to remove the tastes and odors of iron and sulfur To remove these impurities one would need to chlorinate the water Replacement filters are available that will filter iron and sulfur Ask your dealer or RV supply center about purchasing an iron and sulfur filter if such is desired Figure 11 6 Water Filter Tf you are traveling in an area where
112. gles of the wheels so that they are positioned correctly relative to the vehicle s frame This adjustment maximizes the life of your tires These adjustments require special equipment and should be performed by a qualified technician Tire Rotation Rotating tires from front to back and from side to side can reduce irregular wear for vehicles that have tires that are all the same size Look in your owner s manual for information on how frequently the tires on your vehicle should be rotated and the best pattern for rotation 1413 ROUTINE MAINTENANCE A Tire Rotation Example For maximum mileage rotate your tires every 5 000 miles Follow correct rotation patterns Rear and Four Wheel Drive Front Wheel Drive Vehicles Vehicles FRONT FRONT N Pees ii dics ace Littiiiitid AAA i AE AAA 4 4 R D A P pi vs NAF LL LY ae NSE ES PAPA LL SSS tif a LELLI ES PON MAP Y NY i Py rer ZA LV SS PARDO ff APDIP SL IS PAZ SA FHIZITIRTLT 2122708 Fr TI gt in us AN X AN E 3 ur PPAF I SSS Tire Repair The proper repair of a punctured tire requires a plug for the hole and a patch for the area inside the tire surrounds the puncture hole Punctures through the tread can be repaired if they are not too large but punctures to the sidewall should not be repaired Tires must be removed from the rim to be properly inspected before being plugged and patched Tire Fundamentals Fede
113. grams are viewed featuring the Dolby Surround Sound system As this home theater system offers many entertainment options it is worthwhile to read the manual thoroughly before attempting extensive use of this system This system will also play CDs and MP3 disks among other media Figure 4 13 Home Entertainment Theater System Infrared Repeater The Allegro Bay may feature an infrared repeater Figure 4 14 which enables the owner to utilize the satellite remote control from various areas of the coach An optional infrared repeater will be located by an optional mid TV To utilize the infrared repeater locate the one inside the cabinet Figure 4 13 that contains the DVD player Peel the adhesive backing from the back of the infrared repeater and line the infrared repeater against the satellite receiver s infrared repeater This will allow the infrared repeater to operate when the satellite remote control is directed toward the infrared repeater situated next to the TV You will now have the convenience of changing the satellite receiver Figure 4 14 Infrared Repeater channels from various areas of the coach AM FM CD Stereo System Your motor home will be equipped with a Magnadyne AM FM CD Stereo system Figure 4 15 To properly operate the stereo system it is important that you read the information provided with the system To turn the unit on and off push the POWER button To select a Play Source such as the radio
114. has been flushed turn the supply off Connect the other end of the hose to the city water connections on the motot home Once the city water fill valve is opened water is supplied to the freshwater system including the hot water heater faucets and toilet Turn on the water supply and open all of the faucets to clear any trapped air within the plumbing lines within the motor home Once any air pockets have purged from the water lines and Figure 11 5 City Water Connection water flows freely close all of the faucets The city water supply is pressurized usually 60 80 psig therefore the water pump is not needed when the water system of the motor home is connected to the city water system To disconnect the motor home from the city water supply close the valve and remove the hose from the city water supply Disconnect the hose from the city water connection drain it and store the hose in the water compartment of the motor home Filling the Freshwater Tank The freshwater tank is normally filled from the city water connection The city water valve located in the service compartment near the water connection determines whether the city water is going through the motor home water system or into the freshwater tank Important Be sure the potable water fill cap is removed when filling the freshwater tank from a city water supply which is typically under 60 80 psig pressure Failure to do so may result in inadvertent expansion
115. heating water up to desired temperature For general maintenance of the water heater or specific information about select steps in operating the water heater please refer to the owner s manual for this appliance contained in the Owner s Information Package Warning DO NOT STORE any combustible or flammable substances near or adjacent to the water heater Provide adequate space for ventilation and air circulation Water Heater Storage If the motor home is to be stored during the winter months the water heater should be drained to prevent damage caused by freezing water contained in the water heater To drain the water heater first turn off all electrical power turn off the LP gas going to the water heater then turn off the water pump Open both the hot and the cold water faucets to drain the water lines and open the drain plug on the water heater to drain the entire system When re activating the water heater after the motor home is taken out of storage make sure that the entire water system including the water heater has been filled with water and the lines have been purged of any entrapped air before relighting the water heater Failure to do so may allow the water heating element to be turned on before such is immersed in water thereby causing the premature failure of the heating element and voiding the warranty 415 MAJOR APPLIANCES ACCESSORIES Pressure Relief Valve The relief valve for o
116. hese would leave a dull film on the floor Do not use any abrasive cleaners steel wool or scouring powders as these will degrade the floor surface Do not wax or polish your floor Laminate flooring when wet may constitute a slipping hazard so be careful when washing the floor and allow sufficient time for it to dry before having people walk over its surface Immediately wipe up any spills or water tracked in by wet feet to prevent any slipping on the floor 102 INTERIOR FEATURES For truly tough spots or stains use a well squeezed damp mop with laminate floor cleaner simply squirt and mop the affected surface Tough stains like shoe polish tar and asphalt driveway sealer can be removed with nail polish remover the active ingredient is acetone then wipe the treated area with a damp cloth Heavy traffic areas will benefit from the use of mats or throw rugs used near the entrances inside and outside to catch the dirt before it s tracked into the motor home For protection against denting the floor e g legs of fold away chairs one may wish to use floor protectors under such legs as warranted Ceiling The ceiling Figure 10 3 in the Allegro Bay motor home is covered with a padded vinyl headliner which can be easily cleaned with a damp soft cloth and a mild detergent Take care to clean around any vent areas to prevent any buildup of dirt grease or other accumulations Figure 10 3 Typical Ceiling Window
117. hould be placed low and as close to the axle positions as reasonable Too many items on one side may overload a tire The best way to know the actual weight of the vehicle is to weigh it at a public scale Talk to your RV dealer to discuss the weighing methods needed to capture the various weights related to the RV This would include weights for the following axles wheels hitch and total weight How Overloading Affects Your RV and Tires The results of overloading can have serious consequences for passenger safety Too much weight on your vehicle s suspension system can cause spring shock absorber or brake failure handling or steering problems irregular tire wear tire failure or other damage An overloaded vehicle is hard to drive and hard to stop In cases of serious overloading brakes can fail completely particularly on steep hills The load a tire will carry safely is a combination of the size of tire its load range and corresponding inflation pressure Excessive loads and or under inflation cause tire overloading and as a result abnormal tire flexing occurs This situation can generate an excessive amount of heat within the tire Excessive heat may lead to tire failure 1418 ROUTINE MAINTENANCE It is the air pressure that enables a tire to support the load so proper inflation is critical Since RVs can be configured and loaded in many ways air pressures must be determined from actual loads determined by weighing and tak
118. ian using specialized equipment should adjust the regulator LP Distribution System The primary LP distribution system in the motor home is a pipe manifold running the length of the motor home The secondary distribution lines running from this main distribution system are usually copper tubing with flare fittings If any of the gas lines break do not attempt to splice them always run new lines to 27 DRIVING amp SAFETY INSTRUCTIONS maintain the safety of the motor home It is strongly recommended that only qualified service technicians perform this work Remember the main valve at the LP gas tank must be closed whenever any gas appliance is to be installed removed or serviced this process prevents LP gas leakage which could result in a possible harmful explosion If the odor of LP gas Le rotten eggs is ever detected immediately discontinue use of any gas appliances and seek the services of a qualified service technician Recommended Precautionary Practices The following practices are recommended to assure continued safety and reliability of the LP gas system these are of course representative not necessarily exhaustive In all cases use common good sense in the use of the LP system e Visually inspect the LP fill valve before any refueling operation to look for foreign materials or debris remove as necessaty to assure a leak tight connection e Prior to any re fueling operation of the LP gas system shut off all the p
119. ibility of the owner and are not covered by Tiffin Motorhomes Limited Warranty Warning When cleaning the upholstery and fabric of the motor home do not use lacquer thinner nail polish remover laundry soaps or bleach Never use carbon tetrachloride or gasoline for cleaning purposes These substances may cause damage to the materials being cleaned and most are high flammable Walls and Ceiling The wall and ceiling coverings should be cleaned periodically to maintain a new appearance Use a non abrasive cleaner with a soft cloth on the walls Do not use solvents of any kind as those solvents may damage the surfaces being so cleaned Dashboard To keep the dashboard Figure 14 12 in like new condition follow these guidelines DO e Dust and clean the dashboard with a soft damp cloth or chamois wiping the service gently e Use a mild detergent and lukewarm water e Dry the surface after washing and rinsing by blotting with a damp cloth or chamois 1430 Figure 14 12 Dashboard of the Motor Home ROUTINE MAINTENANCE DO NOT e Use harsh chemicals that may damage the dashboard e Use cloths containing grit or abrasive particles or kitchen scouring compounds to clean or dust the dashboard e Subject the dashboard to hard direct blows e Use boiling water strong solvents or other such materials to clean the dashboard as they will soften the plastic Woodwork amp Floors The wood cabinetry should be cared
120. ide road tar tree sap insects and other foreign material Damage caused by exposure to these items is not covered by your warranty agreement Never wash the motor home in direct sunlight while the motor home is hot or with hot water Any accumulation of mud and dirt under the body can cause damaging rust on steel parts Corrosive materials such as those used for ice and snow removal and dust control also can accumulate on the underside of the motor home These Figure 14 1 Motor Home accumulations especially in vehicular areas where mud and other ee foreign materials could collect should be removed by flushing those areas e g the underside of the motor home regularly with water The chance of corrosion can be minimized with frequent washings of the motor home When washing the motor home make certain that the undercarriage and the wheel wells are thoroughly cleaned as well as the exterior of the motor home Do not use strong soaps or detergents for washing the motor home Always use a mild soap in warm water a commercially prepared product for automotive finishes or your local car wash to wash your motor home properly Be careful when using any pressurized washer to avoid loosening any exterior decals or sealants and the like After washing carefully inspect the caulking around the window frames and vents and any other joints to see if any seal separations have occurred Should any re caulking be necessary it is rela
121. igure 7 7 which provide greater protection against inadvertent electrical shocks These specialized GFCI receptacles provide both overload and short circuit protection for the user The electrical receptacles located in the slide out s are wired through the kitchen GFCI The exterior receptacles are wired through the bathroom GFCI Consequently if an appliance plugged into a slide out or exterior receptacle is not working check for a tripped GFCI in the kitchen or bathroom In addition these receptacles protect the user from ground faults between an electrically hot wire and ground The GFCI will not reduce the shock hazard if the short is Figure 7 7 GFCI between a neuttal and hot wite or two hot load wites Receptacle The GFCI should be tested at least once a month The 120 VAC electrical system must be on for the GFCI to be tested To test the GFCI the reset button needs to be pushed in fully before starting the test Push the test button this will cause the reset button to pop out which means that the protected circuits have been disconnected Push the reset button back in until a click is heard this will re activate the protected circuit If the GFCI is IE working properly the reset button will remain in the in position 76 ELECTRICAL FEATURES Electrical Generator The electrical generator Figure 7 8 can be found in an outside storage compartment underneath the motor hom
122. ill be displayed 4 Push the DISP button and the last 8 digits of your 12 digit Sirius Tuner ID Number ESN will be displayed 5 Push the TUNE button to exit Selecting Sirtus Push the MODE button until SIRIUS appears in the display Please be patient as it may take a minute to receive a satellite signal Manual Tuning 1 Push the TUNE button until NORMAL appears in the display 2 Rotate the TUNE knob to select a station from 01 182 Category Tuning 1 Push the TUNE button until CATEGORY appears in the display 2 Push button 1 or 2 to find the desired category 3 Rotate the TUNE knob and select a station Direct Tuning 1 Push the TUNE knob until DIRECT appears in the display 2 Rotate the TUNE knob and select the first digit 0 or 1 3 Push the TUNE knob again 4 Rotate the TUNE knob and select the second digit 1 8 5 Push the TUNE knob again 411 MAJOR APPLIANCES ACCESSORIES 6 Rotate the TUNE knob and select the third digit 1 9 The tuner will start playing the station you have selected when the third digit stops flashing Note Satellite radio signal may be blocked by trees buildings bridges or tunnels To operate the AM FM Weather Band push BAND button to select F1 F2 F3 AM1 AM2 or W weather band Manual Tuning 1 Rotate the TUNE knob left or right and hold until MANUAL appears in the display then release knob 2 Rotate the TUNE knob again left or
123. ilot lights e NEVER under any circumstances check for LP gas leaks with any type of open flame doing so would probably cause an explosion and subsequent fire e Periodically inspect visually the entire LP gas distribution system do so at least semi annually and before any major trips Should problems be noted seek the services of a qualified service technician to make necessary repairs and perform any maintenance Warning The LP gas distribution system in your motor home is designed for liquid propane LP gas ONLY DO NOT attempt to connect and use any natural gas or butane gas systems with this LP gas system Fire Safety As with any enclosed system containing the three required conditions for fire 1 e combustible materials oxygen ignition sources there will exist the possibility of fire Tiffin Motorhomes has taken every precaution and design practice to minimize or negate this possibility but the final determination rests with the owner and user of the motor home Accordingly it is in the best interests of the owners users and their guests to be aware of basic fire safety practices and procedures and those particular features that Tiffin Motorhomes has provided for fire safety 28 DRIVING amp SAFETY INSTRUCTIONS Fire Extinguisher The Allegro Bay is equipped with a fire extinguisher located inside next to the main entrance door see Figure 2 5 rated for both Class B i e grease gasoline diesel fuel flamma
124. ing additional sleeping facilities The sleeping area is realized by lowering the dinette table top and rearranging the seating cushions Specific directions for converting the booth dinette into a bed are as follows Figure 5 3 Dinette Booth Table 1 Remove the seat cushions 2 Remove the wooden fill blocks 3 Fold the table leg upwards while slightly lifting the table then allow the table to swing down and rest between the two booth seats thus forming the bed 4 A filler strip Figure 5 5 is attached to the seat portion via a long Velcro strip of the sofa Simply pull these two pieces apart The filler strip can be conveniently stored Figure 5 4 Dinette Booth Table Converted into Bed 53 CABINETS amp FURNITURE underneath the dinette until you are ready to re convert the bed back into a sofa 5 Re install the seat cushions and back rests to make up the mattress for the bed The living room contains a standard sofa Figure 5 7 which can be converted into a full bed for sleeping as required It may be one of two styles either a jack knife bed or an optional air coil hide a bed sofa sleeper The optional air coil hide a bed sofa sleeper includes an air pump It operates by depressing the black latch and unfolding the bed The sofa is custom coordinated with the d cor of the motor home To convert the sofa into a bed follow these directions 1 Remove the accent pillows 2 Under a seat cushion loca
125. intermediate position will lead to damage to the antenna itself or to the motor home When the TV antenna is raised and adjusted if the TV reception is weak blurred or of inferior quality examine the connections from the TV to the antenna and make sure that the power boost switch is actually on If the symptoms persist then consult your authorized service dealer Television Satellite Dish Control The Allegro Bay may be equipped with a TV Satellite Dish control system direct satellite television The television receiver dish is controlled by a controller in the vehicle which deploys the dish and permits its rotation so that the desired signals may be received Follow the directions in the Owner s Manual for this dish control mechanism to obtain the best orientation of the satellite dish for desired television reception There must be a clear line of sight to the southern sky Mountains buildings trees telephone poles etc can all block the satellite signal from reaching the dish igure 4 9 to permit access to A AAA Fiqure 4 9 TV Satellite Dish Tri Pod Hookup The tri pod hookup will use a high isolation A B Top Push Button Switch Figure 4 10 which will allow the user to switch between two input sources The A switch will allow the user to operate the optional coach satellite and the B switch will allow operation of an external portable satellite dish this dish is not included with the motor
126. it is the owner s responsibility and is not covered by the Tiffin Motorhomes Limited Warranty e Sanitize the fresh water system e Wax and buff all gel coat surfaces on the vehicle as described previously in this chapter 1434 ROUTINE MAINTENANCE Winterizing To store your vehicle for the winter months it is necessary to winterize the water system to hel you nths ty y p prevent freezing of this system To do this follow these instructions 1 Drain all the water from the water system including the holding tank s the hot water heater and the water tank also drain the optional water filter if installed For the holding tank s open the gate valve s to drain the tanks NOTE This procedure is to be performed only at a wastewater pumping station to prevent dumping of contaminated water elsewhere For the hot water heater remove the outside cover and then remove the drain plug When this tank is drained replace the drain plug and then replace the cover For the water tank open the green handled valve to drain the tank then close the green handled valve If an optional water filter is installed remove the filter cartridge and store it in a clean environment e g resealable plastic bag empty any excess water from the filter housing and replace the housing 2 Turn the hot water heater by pass valve located in the water service compartment to the by pass position to prevent filling the water heater tank with antifr
127. itch and the cable is again connected to the 7 pin connector make sure the resultant connection is tight and solid so that the connection won t jar loose during use Several supplemental methods to secure that connection have been used some of which include securing the connection with a strong rubber band or with Velcro type fasteners to provide a supplemental mechanical backup to the actual electromechanical connection 7 10 ELECTRICAL FEATURES Should a conversion adapter to convert the round seven pin connector to a flat four pin connector be needed such an adapter may be purchased from any RV after market store 7 11 SLIDE OUT FEATURES Chapter Slide Out Features 8 1 SLIDE OUT FEATURES SLIDE OUT OVERVIEW Warning BEFORE ACTIVATING THE SLIDE OUT FEATURES please read the slide out room instruction manual first Additionally the motor home must be parked and the leveling jacks must be used to level the motor home PRIOR to activating the slide out features General Considerations Please Note The Slide Out Room requires semi annual inspection i e every six months to assure that the slide out mechanism is properly aligned and functioning correctly Please make sure that this inspection is performed every six months to correct any possible misalignments The slide out room feature is actuated by means of a readily accessible rocker switch Figure 8 1 The rocker switch must be manually held down in th
128. ize yourself with the proper operation of the motor home and all its features before you attempt to use your motor home on the road Tiffin Motorhomes Limited Warranty The Tiffin Motorhomes limited warranty was provided to you by your authorized Tiffin Motorhomes dealer during the pre delivery inspection When you inquire about your Tiffin Motorhomes warranty please refer to this document Should you need or desire an additional copy or other information please contact Tiffin Motorhomes Incorporated 105 2 Street NW Red Bay AL 35582 U S A Telephone 256 356 8661 Facsimile 256 356 8219 E Mail info tiffinmotorhomes com Tiffin Motorhomes will be pleased to send you an additional copy or any other information requested as may be warranted Major Equipment Manufacturers The following list is a compilation of the vendors and suppliers of the major subsystems and components of your Allegro Bay This list is provided for your convenience and is not meant as a complete substitution of the 13 GENERAL INFORMATION literature and accompanying how to contact us information supplied by those vendors and suppliers in your Owner s Information Package see below for particulars Where appropriate web site information is provided for computer usets Atwood Mobile Products o LP Gas Water Heater Denso Corporation Flexsteel Industries Kwikee Notcold Inc Onan Corporation Panasonic Corporation Power Geat RV Products Colem
129. k Top 45 MAJOR APPLIANCES ACCESSORIES time for the unit to cool before re installing the covers over the cook top To light a cook top burner push down on the knob for that burner and turn counterclockwise to the ignite position Continue to hold down the knob fully until the spark ignites the gas and then continue to hold the knob down for another 5 10 seconds this additional time is required for the thermocouple to be heated sufficiently to activate the safety mechanism the thermocouple will automatically cut off the gas flow if the burner goes out Then release the knob and rotate it to the desired cooking setting To turn the cooking flame off turn the knob clockwise to the off position For additional safety and use precautions be sure to read the manufacturer s owners manual before using the cook top for the first time The optional oven Figure 4 7 has a piezoelectric ignition source rather than a pilot light to start the oven To light the burners turn on the gas control knob wait a couple of seconds then push the red DSI direct spark ignition button until a flame appears If the burner does not start after a few attempts discontinue the process let the released gas dissipate then try the process again The burner knobs operate in a counter clockwise CCW manner and must be gently pushed inwards as they are being turned If the oven doesn t have a piezoelectric igniti
130. kout condition indicator light on When the water eventually cools reset the system by turning the switch to the off position for at least 30 seconds then turn the switch back on If a lockout condition persists contact your authorized dealer 414 MAJOR APPLIANCES ACCESSORIES 120 Volt AC Electrical Operation 1 For electrical operation use the power switch on the water heater depending on the particular model that switch may be located either at the front or at the rear of the water heater 2 Completely fill the water heater with water and purge the hot water lines of any trapped air 3 Turn the power switch located on the water heater on NOTE Turning the power on to the water heater without having previously covered the water heating element with water may quickly burn out the element and void the warranty 4 After awhile check the water heater for proper operation the water temperature should be approximately 140 F 60 C 5 If the manual reset high temperature limit switch should trip the circuit breaker reset the switch by depressing the reset button use a pencil or other non metallic object to depress the reset button If the high temperature limit switch should again trip the circuit breaker contact an authorized service technician or an authorized dealer 6 Both the electrical and gas operations of the water heater may be used simultaneously to reduce recovery time of
131. l have an accompanying audible alarm so the owner should not rely solely on the audible alarm for fault indications NOTE To operate the refrigerator in the LP gas mode the 12 VDC power source must be operational otherwise the refrigerator will not operate on LP gas If the refrigerator is operating in the LP gas mode and the 12 VDC power is disconnected the refrigerator will cease operating 43 MAJOR APPLIANCES ACCESSORIES On the refrigerator the thermostat function controls both the gas and electrical operations this eliminates the necessity of resetting the temperature each time one switches from gas to electrical service or vice versa Press the temperature selector button until the light near the desired setting is illuminated 1 through 9 After initial start up the thermostat should be moved from the coldest setting to the desired setting which is usually around mid range on the scale i e 4 or 5 Dometic Refrigerator Optional To start the Dometic refrigerator gi 4 4 optional side by side shown in picture press the main power on off button left hand side of panel shown in Figure 4 3 to the down position Then press the temperature selector button right hand side of the panel until the desired setting is illuminated 1 e one has selected one of the indicator lamps each being numbered 1 through 5 where 1 represents
132. ld take about 10 15 turns until some resistance is noted Once the antenna has been raised slowly rotate the antenna to receive the best picture on the channel of choice this rotation is accomplished by pulling down on the directional handle with both hands until it disengages from the ceiling plate and then Figure 4 8 Television Antenna 47 MAJOR APPLIANCES ACCESSORIES rotating the antenna until optimal reception is realized If your location is within a metropolitan area you may need to rotate the antenna for each different station desired to aim the antenna towards each particular station If the location of the motor home is remote from any metropolitan area the antenna once positioned for a particular station should be adequate for all other stations capable of being received from that particular area Some experimentation may be required to determine the best setting for each location of the motor home and the stations desired to be viewed Prior to moving the motor home the TV antenna must be retracted To lower the antenna rotate the directional handle until the pointer on that handle is aligned with the pointer on the ceiling plate then turn the elevating crank counter clockwise CCW about 10 15 turns until some resistance is noted to lower the antenna and lock it into its retracted position for travel DO NOT partially lower the antenna it must be either fully deployed raised or retracted lowered any
133. lier Figure 6 1 Typical Motor Home Chassis TYPICAL CHASSIS ITEMS COVERED UNDER WARRANTY BY THE CHASSIS MANUFACTURER Steering Wheel Steering System Instrument Panel Engine Transmission Chassis Frame Axles Fuel Tank Suspension and Springs Front End Alignment is not covered Tires and Wheels Brakes Exhaust System Leaf Springs Alignment The Allegro Bay motor home you have purchased has been aligned at the factory prior to shipment to you During the first 10 000 miles of operation of your Allegro Bay the chassis will have a tendency to settle and readjust itself in response to the loading of your motor home Although it normally is not necessary to realign the Allegro Bay before the first 10 000 miles of use it is nonetheless recommended that you have the Allegro Bay alignment checked after the first loading of the motor home However if you feel that you have noted some discrepancy or anomaly in steering operation please contact your chassis manufacturer or call Tiffin Customer Service at 256 356 0261 to address your concerns 62 ELECTRICAL FEATURES Chapter Electrical Features ELECTRICAL FEATURES General Information There are two electrical systems in your Allegro Bay motor home these are the 12 volt DC VDC system and the 120 volt AC VAC system Most standard appliances require the 120 VAC system while the majority of the lighting systems used in the Allegro Bay use the 12 VDC system The elec
134. line LP gas and other petroleum based products is a deadly gas which can kill motor home occupants if allowed to accumulate in sufficient concentration Assure that all engine operations are not restricted tailpipes and exhaust ports should not be blocked or restricted in any way Additionally any accumulation of exhaust gases outside or underneath the vehicle should be avoided as such may enter the motor home through windows or vents be careful how and where the motor home is parked to avoid such conditions Regularly monitor outside conditions to assure that all exhaust gases can readily be dissipated and kept out of the motor home The most susceptible people to CO poisoning are unborn babies small children pregnant women senior citizens and people with cardiovascular or respiratory problems Consequently it is prudent to check the CO monitor regularly for normal operation and to remain aware of the symptoms of CO poisoning which include dizziness nausea vomiting muscular twitching throbbing in the temples incoherent thinking and speech weakness sleepiness and intense headaches Warning Never sleep in a motor home when the engine is running engine exhaust fumes could enter the motor home and cause disability or death Regularly check the exhaust system to note any leakage sites and if found discontinue use of the motor home until they are repaired by a competent qualified service technician Do not attempt repairs
135. lly loaded as the user would have it for travel including occupants Moreover it is necessary to weigh each tite position individually Overloading the motor home can produce problems with the tires wheels springs brakes drive train and other motor home assemblies In addition an overloaded motor home uses more fuel is more difficult to handle properly and can lead to driver fatigue more quickly In a worst case condition if any component should fail this could result in loss of control of the motor home and subsequent damage In certain states the Highway Patrol routinely weighs motor homes to check for overloaded axle weights Therefore there are many good reasons for assuring that the motor home is properly loaded and not overloaded this can be accomplished through a proper weighing of the fully loaded motor home One can find various places that have certified public scales where one s motor home can be weighed For example moving and storage company lots farm suppliers with grain elevators gravel pits recycling companies and large scale commercial truck stops ate some of the possible locations for weighing the motor home One can also check the Yellow Pages of the telephone book for scales public or weighers to determine other locations for weighing the motor home 1425 ROUTINE MAINTENANCE A brief overview of the procedure for weighing the motor home is shown in the accompanying figure WEI
136. ly at the base of the window The majority of these problems can be addressed by managing moisture generated inside the motor home Minor condensation issues are not unusual especially for RVs used in colder climates The key is to manage this small amount of moisture if evident by wiping the surface and as discussed in the Control Relative Humidity section maintaining a reasonable relative humidity within the unit To help minimize window condensation use exhaust fans vented to the outside avoid drastic changes in thermostat 146 ROUTINE MAINTENANCE settings do not use vent free heaters and use window coverings wisely For example make sure to open curtains or blinds during the day to allow air to circulate and warm the window surface Carpet Care and Moisture Management To keep your carpet serviceable and looking new for years to come the carpet should be cleaned when it shows signs of discoloration or traffic patterns A steam cleaning system should be used to clean the carpet unless other noted in your warranty information To manage moisture from the cleaning process the cleaning system needs to be capable of extracting the excess water from the carpet after it has been cleaned Important Be sure the carpet is thoroughly dry before closing up the RV for storage Water from the cleaning process can cause significant damage to the RV if the carpet is not completely dry before closing up the motor home for an extended perio
137. m accessories include a towel bar and a tissue holder I The single handled faucet in the bathroom was chosen to match the and using a soft cloth for subsequent drying and use care to prevent scratching or marring it The Figure 11 3 Bathroom 11 2 PLUMBING amp BATH FEATURES specified decor The bathing facilities installed may be a fiberglass shower or combination shower tub with a glass shower door or fabric curtain The tub faucet hose showerhead and bracket are fashion coordinated Water Pump The water pump is self priming and totally automatic operating on demand whenever water is required The water pump is used to pressurize the fresh water system i when the unit is not connected to city water The switches Figure 11 4 to this pump may be located in the bathroom monitor panel and or sanitation service compartment To start the water pump follow these instructions 1 Fill or partially fill the fresh water supply tank 2 Open the kitchen and bathroom faucets Figure 11 4 3 Turn the water pump switch on and allow the water to fill the water ae line and the hot water heater 4 Close each faucet after it delivers a steady stream of water close the cold water faucet first Leave the hot water faucets on until they also deliver a steady stream of water This procedure will assure that the water heater is filled with water 5 The water pump should stop running once all faucets are closed 6
138. me remove the sensor activation strip if such was not performed during the pre delivery inspection Please check the CO LP gas detector to verify that the detector was properly activated and is ready to provide the necessary protection If in doubt please contact any qualified service technician for more detailed assistance Warning Liquid Propane LP is extremely flammable and when contained explosive when mixed with air Consequently never check for leaks in LP gas lines or appliances with an open flame or sparking devices Do not use any ammoniated or chlorinated household type detergents for bubble testing possible leak sites these detergents may generate fissures or cracks on the metal tubing e g copper and flared fittings e g brass Have your LP gas system leaks repaired ONLY by a qualified service technician do not attempt these yourself Keep the main valve to the LP gas tank closed and all appliances turned off when the motor home is stored If any of the valves do not close leak tight by hand have those valves examined and repaired by a qualified service technician DO NOT under any circumstances attempt to use a faulty LP gas system and or appliances as such represents a safety hazard If the alarm persists in re arming and giving further alarms ventilate the motor home by opening doors and windows and then check for possible LP gas leaks If the leak cannot be readily found then close the main
139. me a heavy or prolonged rain or blustery winds are anticipated it would be advisable to close the awning Similarly if the awning is to be left unattended for any prolonged length of time it would be prudent to close that awning Retracting the Awning 1 Make sure that nothing e g nearby tree patio torches obstructs the intended movement of the awning 2 One can either use the control box or the key fob to retract the awning For the control box press the rocker switch downwards to retract the awning for the key fob press the retract button on the key fob either action will cause the awning to retract to its fully closed position If there is a remote switch inside the motor home one can retract the awning from inside the motor home by pressing that rocker switch downwards to the retract position NOTE If one wishes to protect the awning automatically from possible windy conditions which may damage the awning set the wind sensor switch on the console to the on usually upper position To disable this function set the wind sensor switch to the off usually down position 133 WINDOWS AWNINGS VENTS DOORS Emergency Retracting Procedure for the Awning If the automatic retracting of the awning isn t possible one may manually close the awning using the following procedure 1 Slide the pull strap provided into the utility slot of the Fabric Roller Tube Torsion Assembly FRT
140. mine the area immediately above the proposed parking site for obstructions e g tree branches and limbs signs overhead wiring If the motor home is to be backed into the proposed parking site strive to have that site be on the driver s left hand side as this will allow the driver to watch the rear of the motor home Back up slowly and use the side mirrors and the optional back up camera as a guide or better yet have another person outside provide supplemental guidance to help park the motor home When the motor home is finally situated shift the transmission into the park position and engage the emergency brake and then turn off the engine Activate the leveling jack system see Chapter 9 for more detail to level and stabilize the motor home If the motor home is to be powered externally connect the 120 VAC power to the motor home Turn on the LP gas valve at the LP tank Connect the fresh water supply and sanitize the water systems see Chapter 11 as needed Connect the waste drain hose to the external sewer hook up Start the refrigerator water heater and furnace as warranted Light the oven pilot light if so equipped as needed Certain appliances such as the refrigerator will not work properly if the motor home is not level so be sure to complete the motor home leveling process before activating any of the appliances Towing Hitch The Allegro Bay is fully capable of towing typical motor vehicles th
141. minimize their use The air conditioning system is the major consumption device of electrical power in the motor home When this system is being used in an RV park cumulative use of these air conditioning systems by the resident motor homes can create at times a bigger demand for electrical power than is actually available Accordingly at such times a brown out condition may arise this is when the AC voltage normally available drops to a lesser value e g 10 20 below normal or more Brown out conditions cause appliances to draw greater currents to make up for the reduced voltage thereby causing circuit breakers to trip or fuses to blow Under such conditions your own motor home 33 HEATING amp AIR CONDITIONING is not at fault simply reset your breakers and or replace your fuses Should such conditions continue one may wish in turn to reduce the electrical load in this case turn off the air conditioning system for awhile or start the electrical generator To cool the motor home the thermostat inside the Allegro Bay is used this is the same thermostat which controls the furnace functions described eatlier The air conditioned cooled air is emitted through the vents which are located in the roof throughout the entire coach The discharge and return air vents run parallel front to back on the ceiling Note that the return vents are similar to the air conditioning vents This system allows even distributi
142. n Hold the awning in the down position until you ate ready to roll up the awning BE CAREFUL the awning will try to roll up as soon as the locking lever is flipped to the ROLL UP position 4 Slide the pull strap to the center and by using that strap to control speed allow the awning to return to the side of the motor home Allow the strap to wind diagonally to prevent a bulge in the fabric of the awning 5 Tighten the black adjustment knob and flip the travel lock latch down Repeat this process on the other side of the awning The awning is now fully retracted and is ready for travel NOTE Be sure that the awning is fully locked into position on both arms before travel Failure to do so may cause the awning to deploy when the motor home is in motion Vents The kitchen has a 12 VDC Fantastic vent fan Figure 13 6 installed to exhaust kitchen odors and heat buildup from cooking The vent fan can also be used to change the air in the motor home e g if it becomes musty or smelly To operate the fan first turn the knurled knob to raise the external cover on the Figure 13 6 Exhaust Fan 135 WINDOWS AWNINGS VENTS DOORS outside of the fan then turn the fan on to the desired setting When the fan is turned off remember to close the outside cover on the fan by turning the knurled knob this will keep any form of precipitation or particulates e g dust pollen from entering the motor home
143. n If you have particular sensitivities to dust mites mold or mildew you should exercise care to minimize any direct exposure to these allergens Warning Note before traveling If you plan to travel with your SLEEP NUMBER mattress into mountainous regions either 1 temporarily disconnect the mattress from the pump hose to allow air to escape or 2 partially deflate the mattress chamber to a Sleep Number of 20 Rapid changes in altitude will affect the air pressure inside the mattress The chamber may be damaged if the pressure becomes too great 56 CABINETS amp FURNITURE 57 STRUCTURAL FEATURES Chapter Structural Features STRUCTURAL FEATURES Chassis Features The chassis Figure 6 1 of your Tiffin Motorhomes Allegro Bay was built and is warranted by Ford Freightliner or Workhorse the chassis manufacturers The operating instructions for the specific chassis are included in the Chassis Owner s Manual which is provided with your Allegro Bay and is a part of the Owner s Information Package furnished to you by your Tiffin Motorhomes Dealership Before you begin using your Allegro Bay please read and follow all recommendations for the proper care operation and maintenance of the chassis this will assure you of pleasant trouble free use of your motor home Should you have any questions about the chassis however you should contact your chassis manufacturer as noted in the literature described ear
144. nd may cause additional damage to the motor home Before the water heater is to be used first fill the fresh water system and purge the water lines to and from the water heater by opening all the hot water faucets until water steadily flows from each one and no spurting or hissing sounds are further heard The water heater holds 6 gallons of water and uses either the LP gas system or the 120 volt AC electrical system to operate the heater Proper and safe operation of the water heater requires that all safety information provided in the owner s manual be read and understood before placing the water heater in service Take the time to become familiar with this manual provided in the Owner s Information Package The water heater is designed for operation either with LP gas or 120 volt AC electricity Both modes of operation are now presented LP Gas Electronic Ignition Operation 6 Gallon Model 1 2 Turn the remote switch to the on position If the remote switch light stays on longer than 15 seconds turn the remote switch to the off position and wait 5 minutes Repeat Step One For 6 Gallon Models only For complete shutdown and also before any servicing a Turn the remote switch to the off position b Remove the red wire from the left hand terminal of the ECO switch ECO to valve If the water heater fails to operate because of high water temperature the heater will go into a loc
145. ng from inverter to converter When the Allegro Bay is connected to an external power soutce or the generator is being used to supply power the converter will automatically switch on to charge the 12 VDC batteries For more detailed information consult the manufacturer owner s manual located in the Owner s Information Package Automatic Transfer Switch Your Allegro Bay is equipped with an automatic transfer switch When the generator is turned on this switch automatically transfers from external power to generator power There will be a slight delay between the start of the generator and the electrical connection being made this delay allows the generator to reach normal operating speed without needing to supply a required load When the Allegro Bay is plugged into an external source a click will be heard in the transfer switch box this is a normal function and merely indicates that the unit is changing over from an external power source to the generator Resettable Circuit Breakers The resettable circuit breakers Figure 7 11 are located in the external storage compartment just forward of the entrance door When the circuit breakers are shut down or electrically tripped they must be manually reset These breakers protect the slide outs the AC ignition the electric step the 30 amp ignition system and the 12 VDC disconnect system As needed manually reset the circuit breaker or breakers as shown in the Figur
146. nter perform these inspections periodically and perform necessary tesealing when Figure 14 2 Seals of Windows and Doors necessary 143 ROUTINE MAINTENANCE Proper Sealants for Application The following sealants are recommended for specific sealing applications as noted in the table Recommended Sealants for Specific Sealing Applications SEALANT APPLICATION Plas T Cote Metal or fiberglass roof Surebond SB 140 Rubber laminated to metal roof and ALL SKYLIGHTS Carlisle 502 LSW Self Leveling Sealant Rubber roof over wood base Silicone Sealant To cover butyl and other sealants not to be used as the main sealant Parbond To seal across tops of windows and the like on exterior surfaces where silicone is not used Striping and Decals The striping and decals Figure 14 3 on your motor home normally require very little maintenance Treat these as you would any painted surface on your motor home Wash them with mild soap and warm water or any retail cat soap Never wash the motor home in direct sunlight while the motor home is hot or with hot water Rinse thoroughly to prevent accumulation of any soap residues Use caution with high pressure wash nozzles Keep such nozzles at least 18 inches from the edge of the decals during any washing operations If this is not followed high pressure water nozzles may cause the decals to loosen and subsequently to peel Test small sections of decals when using any type of cleaning solu
147. on for the returns instead of forcing an excess amount of return air through two smaller openings The even return system takes more of the hot air from the set i Figure 3 2 Round motor home thereby providing cooler air throughout the unit The air Vent Filter conditioning vents that are mounted on the ceiling are round vent filters Figure 3 2 that need to be periodically checked for dust accumulation When dust has accumulated on the filters remove them and wash in a mild detergent and warm water Thermostatic Controls The following is a brief overview of how best to use the thermostat Figure 3 3 For more detailed instructions please consult the thermostat literature in the Owner s Information Package The thermostat will have three switches that operate the Fan Mode Thermostat and Fan Speed To operate the Fan mode There are three levels Auto On and Off To operate the Thermostat There are four levels Cool Off Gas Heat ot Electric Heat To operate the Fan speed The levels range from low to high One can move the setting the level of power desired Figure 3 3 Thermostat A switch that allows one to increase or decrease the temperature of the coach is also positioned on the thermostat The user can set an exact temperature with this switch NOTE There is an approximate 2 minute time delay after selecting cooling function for refrigerant compressor to start NOTE If the Comfort Control is
148. on of tires has been the industry standard for the past 20 years Next number This two digit number is the wheel or rim diameter in inches If you change your wheel size you will have to purchase new tires to match the new wheel number Next number This two or three digit number is the tire s load index It is a measurement of how much weight each tire can support You may find this information in your owner s manual If not contact a local tire dealer NOTE You may not find this information on all tires because it is not required by law M S The M S or M S indicates that the tire has some mud and snow capability Most radial tires have these markings 14 15 ROUTINE MAINTENANCE Speed Rating The speed rating denotes the speed at which a tire is designed to be driven for extended petiods of time The ratings range from 99 miles per hour mph to 186 mph These ratings are listed below NOTE You may not find this information on all tires because it is not required by law 106 mph 118 mph For tires with a maximum speed capability over 149 mph tire manufacturers sometimes use the letters ZR For those with a maximum speed capability over 186 mph tire manufacturers always use the letters ZR U S DOT Tire Identification Number This begins with the letters DOT and indicated that the tire meets all federal standards The next two numbers or letters are the plant code where it was manufactured
149. on soutce light the oven by pushing inward on the oven control knob and rotating it CCW to the pilot on position then light the oven pilot light located at the back left hand side of the oven burner this may take a few seconds until the air in that line is purged and replaced with the LP gas Do not attempt to Fig re 47 Oven Optional adjust the oven pilot light as it has been factory adjusted and factory set To extinguish the oven pilot light when use of the oven is concluded push inwards on the oven control knob and turn that knob clockwise CW to the off position If the Allegro Bay is equipped with an optional oven that oven comes with a multi burner cook top having a bi fold countertop cover matching the same d cor as the counters in the motor home This bi fold cover both provides protection to the burners when they are not in use and additional counter space as needed Before any cooking on the cook top is attempted the bi fold cover must be folded up and back from the cook top so that the cooking surface is free and unobstructed Do not replace the cover immediately after using the cook top wait until those surfaces are cool to the touch before replacing the cover Never use the cook top range when the motor home is in motion As a safety feature the following label will be noted in the cooking area 4 6 MAJOR APPLIANCES ACCESSORIES Warning DO NOT USE cooking appliances as a heating source for
150. ontainer contains liquid propane under high pressure The liquid when it passes through the tank valve to a lower pressure vaporizes into a gas and then passes through a regulator to maintain a constant pressure This gas then is the actual fuel distributed through the LP gas manifold system to the LP based appliances used in your motor home Figure 2 4 Liquid Propane Tank 26 DRIVING amp SAFETY INSTRUCTIONS LP appliance lighting problems are typically caused by an improperly adjusted gas regulator NEVER attempt to adjust or reset the gas regulator yourself as an authorized service technician is needed to make these adjustments As a good preventive maintenance activity the regulator should be checked semi annually by a service technician and also before every extended trip Even though the LP gas system is leak checked and verified at the factory at the time of manufacture normal usage travel vibrations etc could loosen the fittings Consequently it is wise to check the gas fittings periodically for leak tightness One can daub some leak detector solution e g a liquid soap like solution on all the fittings connections and junctures when the system is under pressure Should there be any leaks small bubbles will appear at any leak sites Generally loose fittings can be tightened with non sparking tools to stop the leaks If this process doesn t work then one must shut off the main gas valve at the LP
151. oom is to be extended or retracted Also any loose materials or possible obstructions should be removed from the immediate slide out room area Make sure the motor home has been leveled Make sure that the battery is fully charged and connected to the electrical system Verify that there are no obstructions outside which may interfere with the operation of the slide out room Prior to moving the front slide out room in either direction make sure that the driver s chair is moved forward into the driving area as far as possible and is locked into position Make sure that the ignition switch is in the off position prior to using the slide out function if the ignition switch is on the slide out mechanism won t work Push the out portion of the rocker switch allow the slide out room to go to its fully extended position at this point release the rocker switch this locks the room into position Retracting the Slide Out Room 1 Ze Before attempting to move the motor home any slide out room s must be fully retracted Verify that the battery is fully charged and connected to the electrical system With the ignition switch in the off position push the in portion of the rocker switch allow the slide out room to go to its fully retracted position at this point release the rocker switch this locks the room into position 8 3 SLIDE OUT FEATURES Manual Operation Slide Out Room Your Power Gea
152. open door or window Do a head count to make sure that all people and pets within the motor home have moved to a source of fresh air too Do not reenter the motor home or move away from the source s of fresh air until the emergency responders have arrived the motor home interior is sufficiently aired out and the alarm has reverted to its normal monitoring function 1 e no alarms 3 Call the local emergency services i e 911 in most locales to summon help don t go back into motor home to make this call but use a cell phone if available or have someone else nearby make this call 4 Should the CO LP gas detector alarm again activate within a 24 hour period repeat Steps 1 through 3 and also call a qualified service technician to investigate the possible sources of CO e g fuel burning equipment and appliances to locate identify and fix such Warning Test the alarm s operation after each storage period before each trip or at least once per week during use 420 MAJOR APPLIANCES ACCESSORIES 421 CABINETS amp FURNITURE Chapter Cabinets amp Furniture 51 CABINETS amp FURNITURE Cabinets Your Allegro Bay contains cabinetry Figure 5 1 installed throughout the entire motor home from the driver s area through the kitchen dining areas and back into p the bedroom The cabinetry has been designed and l built to provide ample storage space and to be easily accessible and convenientl
153. or dry cleaning only as the bedspread was made with materials treated for stain resistance proper dty cleaning will prolong the life of these materials Minimizing exposure to unnecessary sunlight will prolong and preserve the richness of the colors of the fabrics so it is advisable to keep the shades closed on the sunny side of the motor home whether parked or in transit Figure 10 1 Typical Bedspread Flooring The living room and bedroom floor areas Figure 10 2 are carpeted with filament nylon carpeting treated with Scotchgard a stain resistant coating In the Owners Information Package there is additional literature from the manufacturer concerning the specifics of caring for the carpeting which if followed will prolong the appearance and life of the catpeting Please become familiar with the recommended care and cleaning of the carpeting to assure its prolonged life Laminate flooring is standard in the kitchen and bathroom areas of the motor home For routine cleaning vacuuming the floor of using a dust mop on it would normally be sufficient Figure 10 2 Typical Flooring Carpeting and Tile If more thorough cleaning is warranted the flooring can be wiped with a damp cloth Spills can be wiped up with a cloth In any sandy or gritty areas sweep or vacuum regularly to avoid undue scratching of the laminate surface Do not use any soap based detergents or mop and shine products as t
154. or wheel center member which can be mounted on a vehicle Normal occupant weight This means 68 kilograms 150 Ibs times the number of occupants specified in the second column of Table I of 49 CFR 571 110 1421 ROUTINE MAINTENANCE Occupant distribution The distribution of occupants in a vehicle as specified in the third column of Table I of 49 CFR 571 110 Open splice Any parting at any junction of tread sidewall or innerliner that extends to cord material Outer diameter The overall diameter of an inflated new tire Overall width The linear distance between the exteriors of the sidewalls of an inflated tire including elevations due to labeling decorations or protective bands or ribs Pin Weight The vertical trailer load supported by the king pin of a fifth wheel hitch Ply A layer of rubber coated parallel cords Ply separation A parting of rubber compound between adjacent plies Pneumatic tire A mechanical device made of rubber chemicals fabric and steel or other materials that when mounted on an automotive wheel provides the traction and contains the gas or fluid that sustains the load Production options weight The combined weight of those installed regular production options weighing over 2 3 kilograms 5 lbs in excess of those standard items which they replace not previously considered in curb weight or accessory weight including heavy duty brakes ride levelers roof rack heavy duty battery
155. otor home 2 Use a small dehumidifier which is also very effective in removing moisture from the air Condensation levels are highest during times when a person is cooking or taking a shower in the motor home but these occasions are not the only times condensation is present Walls and ceiling panels may become wet when the moisture accumulates on these surfaces Tiffin Motorhomes does not recommend the use of any catalytic heaters because of resulting extensive condensation ROUTINE MAINTENANCE SCHEDULES Important Always follow the chassis maintenance guidelines found in the chassis manufacturer s owner s manual All routine maintenance is the responsibility of the owner and is not covered by the Tiffin Motorhomes Limited Warranty Use the maintenance record found in Chapter 15 to record all performed maintenance as required Please note that any damage caused by improper or unperformed maintenance is not covered by the Tiffin Motorhomes Limited Warranty Items supplied by other manufacturers may require specific individual maintenance not listed herein Please refer to the manufacturers suggested maintenance guidelines in the Owners Information Package Important Cosmetic adjustments and alignments must be performed within the first three months from date of original purchase for warranty consideration Thereafter 1433 ROUTINE MAINTENANCE these items are considered routine maintenance Monthly e Check the
156. otor home interior and to reduce the effects of the sun s bleaching of interior fabrics curtains upholstery Pat both the driver s and the passenger s windows additional sun visors ate available to permit blockage of the sun s rays which may interfere with Figure 13 1 Windows on Driver s Side driving These shades can be deployed as needed and then moved out of the way when no longer desired In the bedroom one particular window Figure 13 2 will be marked with an EXIT label this is an emergency escape to be used only when normal exits are blocked or inaccessible To use this emergency Figure 13 2 Emergency Exit escape merely lift the red handles at the bottom of the window and push outwards to open the window Should it be necessary to use this exit please look for a secure footing when exiting so that no personal injury is sustained in the process It is also prudent when parking the motor home to be aware of where this emergency exit window will be situated so that it is not inadvertently blocked or impeded e g by a tree or pole from its normal intended operation should such become necessary Awnings Your Allegro Bay may be equipped with an optional power patio awning Figure 13 3 If so use the following directions to operate the awning properly We ther Pro NOTE You may first have to program the key fob which can remotely a activate the awning please con
157. out DO NOT OPERATE any room extension until the leveling and stabilizing procedure has been properly completed DO NOT RETRACT 93 EXTERIOR FEATURES the leveling system until the slide out room has been retracted NEVER operate the motor home leveling system when the slide out is extended Caution DO NOT LIFT the wheels of the motor home off the ground when leveling if done the motor home can lean forwards or backwards when supported only by the leveling jacks Never use the jacks to lift the motor home off the ground to change the tires or perform any under chassis maintenance these jacks are not meant for this type of service and this misuse would be very dangerous to the operator The Allegro Bay is equipped with hydraulic leveling jacks These jacks work in pairs Front right side left side and rear Before extending these motor home leveling jacks the engine must be running the ignition switch must be in the ACC position and the transmission must be in park The parking brake needs to be set and the tires blocked securely then the leveling jacks can be activated Leveling Control System The leveling system requires only minimal effort from the motor home user For manual leveling of the motor home perform the following steps EXTENSION MODE On the leveling system control panel Figure 9 5 press the on off switch to turn on the leveling system this will activate the cont
158. power to 120 VAC power i for the operation of lights appliances televisions and related items The 120 VAC power which is generated by the inverter converter is routed to Figure 7 10 Inverter Control Panel Figure u nn the electrical sub panel located next to the main breaker box under the refrigerator Senne ff inside the vehicle or in the storage compartment if outside the vehicle If your coach is equipped with the optional XM1800 inverter follow the instructions listed below 7 7 ELECTRICAL FEATURES e Use the Green Button to turn the inverter on off o If an external AC source is available generator shore the inverter will automatically pass the AC through whether the inverter is on or off o If the inverter is left on when external AC is turned off the inverter will remain on to power load o Make sure to turn the inverter off when storing DC disconnect switch does not disconnect the inverter e When in inverter mode use gray button to toggle between meters o Input Voltage DC voltage from the battery o Input Current DC amperage usage by inverter o Output Power Wattage used by loads The breakers in the sub panel are labeled to explain where the 120 VAC power is routed Generally the inverter converter supplies power to the microwave kitchen bath and bedroom receptacles and other select receptacles The inverter converter is equipped with an automatic transfer switch which allows automatic switchi
159. r Cable o Select Auto o Select All Channels Analog Only or Digital Only The television sets Figure 4 12 are located in different areas of the motor home Some are standard TV sets and some are optional TV sets depending on your specific floor plan All TV sets are High Definition The televisions are powered by 120 volt AC electricity therefore the motor home must either be plugged into an external source of AC power or using on board power from the generator Detailed operation of the television s is provided in the accompanying owners manuals found in the Owner s Information Package included with the motor home Genetic operations of the television would include a basic on off switch volume up down control channel up down selector and menu up down selector these functions are found both on the television set itself and on the accompanying Figure 4 12 Television Set 49 MAJOR APPLIANCES ACCESSORIES remote that comes with the television set If the motor home has been wired for satellite TV there should be an interior jack or jacks and an exterior jack to connect the satellite system Consult your owner s manual for the satellite system to determine the correct connections to be made Home Theater System The motor home may have a contemporary home theater system Figure 4 13 which offers true surround sound for the front television and also when DVD pro
160. r Over the life of the vehicle the shell will require regular care and maintenance in accotdance with other instructions for exterior cate The shell includes the roof sidewalls windows doors and under floor of the vehicle Particular attention needs to be devoted to ensure these components are maintained to ensure a tight barrier against bulk water intrusion The shell should be inspected er wu BE 5 z Figure 14 5 Inspecting Slide periodically for tears gaps and condition of sealants in accordance with this Out Gasket owner s manual Areas that require maintenance should be resealed utilizing 14 7 ROUTINE MAINTENANCE a similar high quality sealant used by the manufacturer Particular attention should be devoted to ensure the slide outs are functioning properly Each time a slide out is used it should be inspected to ensure proper operation and sealing Figure 14 5 The slide out gaskets should also be inspected to ensure proper sealing when the slide out is operated Use of Your RV It is important to remember that the square footage of an RV is significantly less than that of a single family residence This fact alone will elevate the relative humidity because there is less volume of air to help absorb or dissipate the humidity For example showering and cooking create a lot of humidity in a small area In these instances use of an exhaust fan and opening windows should reduce the relative humidity particularly when living
161. r slide out system is equipped with a manual override that allows one to extend or retract the room in the event of a loss of power Please Note If the slide out room doesn t move when the rocker switch is depressed check the following Make sure the ignition switch is turned off Make sure the battery is fully charged and connected Make sure the slide out breakers haven t been tripped these breakers are located on the firewall After the previous items have been checked and the slide out room still does not move when the rocker switch is pressed follow these simple steps Figure 8 2 to override the slide out room manually 1 Turn off the ignition switch Figure 8 2 Manual Slide Out Deployment Sequence 2 Locate the slide out electrical controller refer to your Tiffin Motorhomes dealer or the Tiffin Motorhomes factory for its location There are two versions of the controller For version 1 unplug the six pin wiring harness to the controller For version 2 remove one of the motor leads either the motor I or the motor II lead from the controller 3 Locate the slide out motor it will be mounted to one side of the slide out rails NOTE If the motor home has an underbelly or a cover over the motor these parts must be removed to access the motor 4 Rotate the brake lever on the backside of the motor counter clockwise CCW looking from the rear of the motor about 1 8 of a turn to the released po
162. ral law requires tire manufacturers to place standardized information on the sidewall of all tires This information identifies and describes the fundamental characteristics of the tire and also provides a tire identification number for safety standard certification and in case of a recall 1414 ROUTINE MAINTENANCE Information on Passenger Vehicle Tires Please refer to the diagram below Radial gt diameter no of height to width aspect ratio Load index amp Nominal width of speed symbol tire in millimeters U S DOT tire Passenger identification number car tire Tire ply composition and materials used Treadwear traction and temperature grades y load rating P The P indicates the tire is for passenger vehicles NOTE Passenger car tires are not recommended for use on trailers because the capacity ratings are not marked on the side walls of these tires In the event a passenger car tire is used the capacity must be de rated by 10 Next number This three digit number gives the width in millimeters of the tire from sidewall edge to sidewall edge In general the larger the number the wider the tite Next number This two digit number known as the aspect ratio gives the tire s ratio of height to width Numbers of 70 or lower indicate a short sidewall for improved steering response and better overall handling on dry pavement R The R stands for radial Radial ply constructi
163. re less bright therefore in the NIGHT position Thus the picture will be easy to view even in a dark place When you set the gear level to the R position with the POWER switch released The monitor is turned on and the picture from the camera connected to the CAMERA A connector appears irrespective of the INPUT knob setting Warning Note on the power of the monitor When you press the POWER switch to release the monitor becomes standby condition The power is not turned off until you set the ignition key to the OFF position 417 MAJOR APPLIANCES ACCESSORIES Warning About the Liquid Crystal Display LCD panel Do not press on the LCD panel on the monitor unit as doing so can distort the picture or cause a malfunction The picture may become unclear or the LCD panel may be damaged Clean the LCD panel with a slightly damp soft cloth DO NOT use solvents such as benzene thinner commercially available cleaners or antistatic spray Warning If your motor home is parked in a cold or hot place the picture may not be immediately clear The monitor is not damaged The picture will become clear after the temperature in your motor home becomes normal Washer Dryer Optional If an optional washer dryer Figure 4 20 unit is installed in the Allegro Bay this appliance is essentially operated as one would normally be used in the home environment This appliance operates on 120 volt AC electricity so power
164. re puts a 50 ppm parts per million residual chlorine concentration in the water system that will act as a quick kill dosage for harmful bacteria viruses and slime forming organisms Concentrations greater than 50 ppm may damage the water lines and or the tank Once the freshwater tank is empty close the drain valves in the water tank Pump the chlorine solution into the tank by first placing the winterizing hose into the chlorine solution Close the valve from the fresh water tank to the pump and open the valve from the solution to the pump Turn the tank fill valve from city water to tank fill Turn on the water pump until all of the solution is pumped into the freshwater tank Turn off the water pump Then close the valve to the solution Open the valve from the tank to the water pump Fill the water tank with the city water tank fill or by using the same method as was used to put the sanitizing solution into the tank Remove the water filter located in the sanitation compartment outside the motor home and install the bypass pipe to allow the sanitizing solution access to the faucet Open each faucet in turn including the kitchen faucet bath faucet inside and outside showers turning on both the hot and cold faucets and flushing the toilet until all of the air has been purged from the pipes and the water runs freely The entire system will then be filled with the sanitizing solution Allow the 50 ppm disin
165. rentially around a tire Tread separation Pulling away of the tread from the tire carcass Treadwear indicators TWI Ihe projections within the principal grooves designed to give a visual indication of the degrees of wear of the tread Vehicle capacity weight The rated cargo and luggage load plus 68 kilograms 150 lbs times the vehicle s designated seating capacity Vehicle maximum load on the tire The load on an individual tire that is determined by distributing to each axle its share of the maximum loaded vehicle weight and dividing by two Vehicle normal load on the tire The load on an individual tire that is determined by distributing to each axle its share of the curb weight accessory weight and normal occupant weight distributed in accordance with Table I of CFR 49 571 110 and dividing by 2 Weather side The surface area of the rim not covered by the inflated tire Wheel center member In the case of a non pneumatic tire assembly incorporating a wheel a mechanical device which attached either integrally or separably to the non pneumatic rim and provides the connection between the non pneumatic rim and the vehicle or in the case of a non pneumatic tire assembly not incorporating a wheel a mechanical device which attaches either integrally or separably to the non pneumatic tire and provides the connection between tire and the vehicle Wheel holding fixture The fixture used to hold the wheel and tire assembly
166. rior compartments to make sure that all cargo and equipment are properly secured so that they won t work loose and become hazards during sudden starts and stops 23 DRIVING amp SAFETY INSTRUCTIONS e Check tires for proper inflation 1 e cold inflation pressure 100 psig or so if the motor home has not been used make sure that the cold inflation pressure is maintained If the motor home has very recently been used make sure that the hot inflation pressure see the tire manufacturer s literature to determine appropriate hot inflation pressure is maintained All tire pressures should be within 1 2 pounds psig of each other unless weight loading dictates otherwise see Chapter 14 Section 14 23 e Examine wheel lug nuts to assure their proper tightness If any lug nuts were found to be loose first check the fit of the wheel to the hub to make sure that the wheel is not mis mounted which would produce a wobbly wheel when the motor home is in motion then tighten the lug nuts e Check all fluid levels e g engine oil transmission fluid coolant power steering fluid brake fluid battery fluid if applicable windshield washer solvent to assure correct levels are maintained Fill any low reservoirs as needed e DO NOT SUBSTITUTE any other fluids for specified oils transmission fluid brake fluid or other hydraulic fluids in most instances substitutions are not acceptable and may void warranties
167. rmation indicates the maximum load and tire pressure when the tire is used as a dual that is when four tires are put on each rear axle a total of six or more tires on the vehicle Max Load Single kg lbs at kPa psi Cold This information indicates the maximum load and tire pressure when the tire is used as a single Load Range This information identifies the tire s load carrying capabilities and its inflation limits Vehicle Load Limits Determining the load limits of a vehicle includes more than understanding the load limits of the tires alone On a motor home there is a Federal certification label that is affixed to either the hinge pillar door latch post or the door edge that meets the door latch post next to the driver s seating position If none of these locations is practicable this label will be located to the left side of the instrument panel or affixed to the inward facing surface of the door next to the driver s seating position 1417 ROUTINE MAINTENANCE The certification label will indicate the vehicle s gross vehicle weight rating GVWR This is the most weight the fully loaded vehicle can weight It will also provide the gross axle weight rating GAWR This is the most a particular axle can weigh If there are multiple axles the GAWR of each axle will be provided For motor homes in the same location as the certification label described above there is a vehicle placard This placard provides tire an
168. rol panel and a green LED will come on to indicate the control system is ready Manual Leveling 1 Press both the ALL switch and the EXT extend switch simultaneously and then release them simultaneously this will cause all four levelers to extend automatically The four levelers will each extend automatically and when each contacts the ground each will stop automatically ENGINE RUNNING x e RK AK iG Note This all extend command must be S a es e PARK NEUTRAL performed first before any other commands will Mo LOW VOLTAGE f ction e273 O WAIT PROCESSING _ CAUTION READ INSTRUCTION MANUAL BEFORE USE Fiqure 9 5 Leveling Control Panel on Dashboard de EXTERIOR FEATURES PANIC STOP If it is necessary to stop the leveling process rapidly any switch can be pressed to initiate a panic stop of all four levelers The total system is still activated To reset the system press the Retract RET and the ALL switches simultaneously Once the levelers have stopped extending look at the bubble level and adjust the levelers as defined in Step 4 If the bubble in the bubble level is towards the front of the motor home either extend the rear levelers or retract the front levelers until the bubble is centered If the bubble is towards the rear of the motor home either extend the front levelers or tetract the rear levelers until the bubble is centered To extend or retract the levele
169. room Area If a d cor coordinated quilted bedspread with accessorized pillow shams and accent pillow s are taid with the bedroom suite it is recommended that the bedspread be dry cleaned only to preserve the quality and integrity of the bedspread for the longest time possible Treatment of the bedspread with any of the stain resistant sprays e g Scotchgard or its equivalent will also make the bedspread mote resistant to the possibilities of stains and fabric damage If maintained properly the bedroom soft goods accessories will provide years of dependable service and maintain the desired d cor established by the motor home owner Figure 5 9 Typical Bedroom Area Select Comfort Mattress Optional Your Allegro Bay may be equipped with an optional Sleep Number Bed by Select Comfort A remote control Figure 5 10 accompanies the bed so that one may control the firmness of his her bed To select your personal Sleep Number follow these steps 1 Lie on the Sleep Number Bed in your normal sleep position holding your remote 2 Press and release any button on the remote to wake it up It will display the current SLEEP NUMBER setting Note _To activate the controller your motor home must be connected to shore power or the generator must be running This is to allow the air pump to operate If you have an idea of what your Sleep Number is enter it on the remote by pressing the firmer or softer pas a Se P R
170. rs in adjacent pairs one can level the motor home in either the extend or the retract mode To do so press the extend or retract switch and then release it then press and hold down the FRONT DRIVER PASS or REAR switch to activate the corresponding pair of levelers 1 e hydraulic jacks Note the bubble level while performing this operation to make sure that the leveling process is going the way that is intended Activate the levelers in pairs until the motor home is level Remember that the levelers can be retracted to facilitate the leveling process Outside visually inspect the leveled motor home to assure that all levelers are contacting the ground If not activate those needing such until they contact the ground When the leveling process is completed press the on switch to turn off the control panel Auto Position Controls If the Auto position is already set or programmed 1 2 3 Press the on off switch to activate the system Press the AUTO switch The levelers will extend and automatically reach the pre set position Auto Position bump back at completion of Auto Position the system will check each leveler to assure that its foot is in contact with the ground During this period the control panel WAIT LED will be lighted To set the Auto Position iF 2 Look at the control panel you have an automatic controller if there is a switch labeled
171. rs the weakest link in the tire wheel brakes hubs axle springs and attaching parts To illustrate if the axle is rated at 15 000 pounds and the tires are rated at 3 200 pounds each as a dual installation then the maximum GAWR would be 12 800 pounds for a four tire vehicle e Towing Guidelines Specific weighing instructions and guidelines are furnished in the Owners Manual see below for a general overview and also Chapter 2 for more specific details 16 GENERAL INFORMATION Weighing Procedures for the Allegro Bay To weigh the motor home properly the motor home should be level when the weighing process is performed Your Allegro Bay motor home has been designed and built in compliance with the recommended limits of the major component system suppliers to provide a realistic CCC However it is up to the final user to provide even distribution of the loads brought into the motor home to prevent uneven loading Once the motor home is loaded it can be taken to any drive on scales or individual wheel scales to determine that the final weight is within specified limits for this motor home The procedure which can be used is as follows First drive the motor home onto the scales so that all wheels are on the scales this provides the gross vehicle weight GVW of the motor home and can be recorded as such The GVW should not exceed the GVWR specified for the motor home Second drive the motor home so that the front wheels are off the
172. ry cables sign or red for the positive cable sign or black for the negative cable so that they can be properly reconnected again later Then disconnect the negative terminal s from the batteries Afterwards disconnect the positive terminals Now the batteries can be removed for storage When the 74 ELECTRICAL FEATURES batteries are moved keep them upright at all times To reinstall the batteries at a later date reverse the above described process While in storage these batteries would require periodic recharging to maintain their full charge Additionally the batteries will over time lose some of the water used with the sulfuric acid in the batteries Following manufacturer s recommendations as found in the Owner s Information Package periodically check the fluid levels in all the cells of the batteries be sure to use safety eyewear during this process and fill those that are low with water distilled or de ionized water is preferred tap water is okay Don t overfill the cells follow the filling directions exactly This battery checkup should be done on a regular basis to realize the fullest service possible from the batteries over the longest time possible If the Allegro Bay is to be stored for an extended period of time the 12 VDC battery system should be disconnected this will prevent unnecessary drain and corrosion of the batteries and their terminals Battery Disconnect Panel The batt
173. s at least on an annual basis If the water 11 6 PLUMBING amp BATH FEATURES pump still runs when all faucets are turned off check for a possible leak Be sure that the drain valves ate closed Connections at the kitchen and bathroom faucets normally seal by hand tightening them and then making an additional half turn with a wrench If a fitting leak persists disconnect it completely and visually inspect it for mineral deposits or foreign material stuck on the sealing surfaces Clean the surfaces thoroughly and reinstall the fitting Take the motor home to an authorized Tiffin Motorhomes service center for additional repairs if the water system continues to leak Follow the winterizing instructions given in Chapter 14 to reduce risk of leaks caused by cracks from freezing pipes Left unchecked freezing damage can be extensive and expensive WASTE WATER SYSTEMS General Information The waste drainage system was designed to provide adequate and safe storage and or disposal of waste materials All of the manufacturing materials used in the fabrication of this system are tested by a nationally recognized testing laboratory The drainage system uses plastic piping and fittings connected to the sinks toilet and holding tanks This plumbing permits the drainage of these fixtures to an outside termination The motor home should be reasonably level for best operation of both of the wastewater systems there are two separate wastewater
174. s in the fuel tanks e After filling any LP system immediately replace and secure all protective covers and caps e After closing the LP valve close and securely latch the LP door to prevent unintentional access or damage e NEVER connect natural gas to the LP gas system LP gas and natural gas are not interchangeable e NEVER use any other burning equipment e g charcoal grills wood stoves butane lights propane lights inside the motor home doing so may cause fires and or asphyxiation Liquid Propane LP Gas System A warning label is conspicuously located near the LP gas container that label reads Warning DO NOT FILL the LP Container s to more than 80 of capacity Any overfilling of the LP gas container s can result in uncontrolled gas flow a prime condition for a fire or explosion The LP container should only be filled to 80 of its capacity the remainder of the cylinder space is a vapor space to contain expansion of that liquid when subjected to varying ambient temperature conditions Filling in excess of 80 of the liquid volume of the container reduces that vapor space and thus creates a condition for possible over pressurization of the container All LP appliances in your motor home have been approved for use in motor homes by a nationally recognized testing laboratory 1 e UL and CSA certified When properly used LP gas is a clean burning fuel which can be dependably used In actuality the LP c
175. securely during testing Tire Pressure Correct tite inflation pressure is essential to maximizing the life of the tires and assuring the safety of the vehicle and its occupants Driving with tires that are not correctly inflated for the load of the motor home is dangerous and may cause premature wear tite damage and or loss of control of the motor home 1423 ROUTINE MAINTENANCE An underinflated tire will build up excessive heat that may actually approach the vulcanization temperature of the rubber and lead to tread separation and or disintegration of the tire Figures 14 6 7 Additionally underinflated tires will also cause poor handling of the motor home rapid and or irregular tire wear and an increase in rolling resistance of the motor home which in turn produces a decrease in fuel economy of operation An overinflated tire will reduce the tire s footprint Le its actual contact with the road thus reducing the traction braking capacity and handling of the motor home A tire that is overinflated for the load that it is carrying will also contribute to a harsh ride uneven tite wear and the tire itself will be more susceptible to impact damage Maintaining correct tire pressure for each loaded wheel position on the motor home is Figure 14 7 Rear Tire critically important and must be a part of regular vehicle maintenance Figure 14 6 Front Tire Tire Maximum Load Rating Federal law requires that th
176. sition This action will release the brake that holds the room in place 5 Locate the manual override for the slide out system 6 The room is now free to move Using a Ys wrench or socket crank IED the room either in or out completely depending on your needs SLIDE OUT FEATURES NOTE Ifthe slide out system is supplied with a gearbox override optional use the crank handle to move the room 7 When the room is fully in or out apply pressure to the wrench or ratchet and return the brake lever to its engaged position this will assure that the room is locked into a secured position 8 Take the unit to an authorized dealer for service Figure 8 3 Typical Allegro Bay Slide Out Fully Extended 85 EXTERIOR FEATURES Chapter Exterior Features EXTERIOR FEATURES Towing Hitch On the rear of the Allegro Bay can be found a Class 3 5 000 pound towing hitch Figure 9 1 capable of handling a tongue weight of 500 pounds This hitch is installed for towing a passenger car to be used when the motor home is parked The wire connector installed with this hitch is a standard seven pin connector For more information on the connector please see Chapter 7 of this Owner s Manual Exterior Sides Figure 9 1 Towing Hitch The sides of your Allegro Bay ate constructed of gel coated fiberglass Figure 9 2 To enhance this feature the Figure 9 2 Typical Exterior Si
177. ss for the other side Slide the pull strap to the right end of the roller and wrap that strap around the main arm Pull up on the lift handle and raise the arm assembly to the desired height Swing the handle in and allow the lock button to snap into one of the holes Repeat this process on the other side of the awning WINDOWS AWNINGS VENTS DOORS 7 Press the release lever at the bottom end of one main arm pull the arm assembly outward to a vertical position and readjust the height Repeat this process on the other side of the awning During any rain lower one end to permit water runoff Caution Since damage resulting from weather is not under warranty anytime a heavy or prolonged rain or blustery winds are anticipated it would be advisable to retract the awning Similarly if the awning is to be left unattended for any prolonged length of time it would be prudent to retract that awning Retracting the Awning 1 Raise the lift handle to release the lock button Lower the main arm to the stop plug Swing the handle in to engage the lock button in a hole Repeat on the other side of the awning 2 Loosen the black adjustment knob lift the slider catch and then slide the rafter arm downwards to the bottom of the main arm Leave the black adjustment knob loose Repeat this process on the other side of the awning 3 Grasp the pull strap and pull towards you Flip the locking lever to the ROLL UP positio
178. sult the owner s manual for the power f awning for directions on the programming process Extending the Awning a m Dometic 1 First examine the area where the awning is to be deployed and Figure 13 3 Optional Power Awning Controller 132 WINDOWS AWNINGS VENTS DOORS make sure that there are no obstructions that may impede the opening of the awning 2 Make sure that the weather conditions warrant opening the awning for example the wind isn t too blustery or no major storm fronts are soon to be expected in the immediate area 3 One can either use the control box or the key fob Figure 13 4 to deploy the awning For the control box press the rocker switch upwards to extend the awning for the key fob press the extend button on the key fob either action will cause the awning to deploy to its fully extended position If there is a remote switch inside the motor home one can activate the awning from inside the motor home by pressing the rocker switch upwards to the extend position Figure 13 4 Key Fob i Awning Controller NOTE If one wishes to protect the awning automatically from possible windy conditions which may damage the awning set the wind sensor switch on the console to the on usually upper position To disable this function set the wind sensor switch to the off usually down position Caution Since damage resulting from weather is not under warranty anyti
179. t important things you can do to avoid tire failure such as tread separation or blowout and flat tires These actions along with other care and maintenance activities can also e Improve vehicle handling e Help protect you and others from avoidable breakdowns and accidents e Improve fuel economy e Increase the life of your tires This section presents a comprehensive overview of tire safety including information on the following topics e Basic tire maintenance e Uniform Tire Quality Grading System e Fundamental characteristics of tires e Tire safety tips Use this information to make tire safety a regular part of your vehicle maintenance routine Recognize that the time you spend is minimal compared with the inconvenience and safety consequences of a flat tire or other tire failure Safety First Basic Tire Maintenance Properly maintained tires improve the steering stopping traction and load carrying capability of your vehicle Under inflated tires and overloaded vehicles are a major cause of tire failure Therefore as 1410 ROUTINE MAINTENANCE mentioned above to avoid flat tires and other types of tire failure you should maintain proper tire pressure observe tire and vehicle load limits avoid road hazards and regularly inspect yout tires Finding Your Vehicle s Recommended Tire Pressure and Load Limits Tire information placards and vehicle certification labels contain information on tires and load limits Thes
180. te the black tab and slide the tab to the left or the right and p then pull upwards on the seat portion of the sofa this will cause Figure5 5 Filler Strip Attached to the Seat the sofa seat to open Portion Figure 5 6 Dining Table amp Chairs extend and convert into a bed There may also be a swivel rocker with an adjustable headrest or a recliner also coordinated with the d cor of the motor home For the driver s seat an optional power seat is available which offers an electric powered six way power seat 1 e movement up down forward tilt reverse tilt having swivel features and recline features for the passenger seat only When the motor home is parked the driver s seat Figure 5 8 can be swiveled to face into the living room To swivel this chair first extend the slide out room see Chapter 8 for additional detail Then move the chair backwards as far as possible to gain clearance from the steering wheel Now the chair can be swiveled without interference Fiqure 5 7 Sofa The control switch for the drivers chair is located on the left hand side in front of the power base controls In a comparable manner an optional power seat is also available for the passenger s seat which also includes the electric powered six way seat having essentially the same controls as that of the driver s seat and it is operated accordingly Figure 5 8 Captain s Chair CABINETS amp FURNITURE Bed
181. temperature mode power level and cooking time For basic operating instructions on the proper use of the microwave and convection oven please consult the specific manual in the Owners Information Package Figure 4 5 Microwave Convection Oven Air Filtration Fan In the Allegro Bay the exhaust or air filtration fan is built into the microwave and its function is to filter the air only it does not exhaust to the outside This range hood is equipped with a multi speed fan and a light for convenient use The hood should be used whenever any cooking is performed to filter any airborne cooking residues and heated ait Additionally the range hood can be used as supplemental filtration of other odors and gases including tobacco smoke candle fumes and related vapors The range hood contains filters which can be removed and cleaned or replaced to assure sustained normal operation Consult the particular owner s manual contained in the Owner s Information Package Cook Top and Optional Oven The Allegro Bay is normally equipped with a two burner recessed Princess cook top Figure 4 6 The 7 cook top has two removable covers which provide additional counter space when the cook top isn t being used To use the cook top remove the covers and temporarily store them where they won t be in the way and then follow the directions for proper use When use of the cook top is over allow sufficient Figure 4 6 Two Burner Coo
182. tenna Television Satellite Dish Control Tri Pod Hookup Television Sets Home Theater System Infrared Repeater AM FM CD Stereo System Cable Telephone J ack Water Heater Water Heater Storage Pressure Relief Valve CB Radio System Antenna Connection Rear View Camera Monitor System Washer Dryer Optional Carbon Monoxide LP Gas Detector Chapter 5 Cabinets amp Furniture Cabinets Furniture Bedroom Area Select Comfort Mattress Optional Chapter 6 Structural Features Chassis Features Alignment 4 7 4 8 4 8 Chapter 7 4 9 10 Electrical Features 4 10 General Information 7 2 4 10 Circuit Breaker Boxes 7 2 4 13 Auxiliary Start Switch 7 3 4 14 Battery Inspection and Care 7 3 4 15 Battery Disconnect Panel 7 5 4 16 ver 120 Volt AC VAC Receptacles 7 5 12 Volt DC VDC Receptacles 7 6 4 16 gas Ground Fault Circuit Interrupt GFCI 7 6 Electrical Generator 7 7 4 18 Inverter Converter 7 7 Automatic Transfer Switch 7 8 Resettable Circuit Breakers 7 8 Fuse Blocks 7 9 Seven Pin Towing Connector 7 10 5 2 5 3 Chapter 8 5 5 bce Slide Out Features SLIDE OUT OVERVIEW 8 2 General Considerations 8 2 Operating Precautions 8 2 Extending the Slide Out Room 8 3 Retracting the Slide Out Room 8 3 Manual Operation Slide Out Room 8 4 6 2 6 2 ALLEGRO BAY OWNER S MANUAL Chapter 9 Exterior Features Towing Hitch 9 2 Exterior Sides 9 2 Security Lights 9 2 Roof Ladder
183. ter button then enter in the appropriate search criteria such as zip code and search radius or dealer name and state then click on Find Locations the dealer s name address and telephone number will be displayed for your use Specification Labels There are two main numbers used to identify your Allegro Bay The Vehicle Identification Number VIN is the legal identification of the completed vehicle The VIN is the number used by the state for vehicle identification and registration TIFFIN MOTOR HOMES Additionally there is a Tiffin Motorhomes identification number Hdi ee es rn The Tiffin number is needed when you plan to make an ee ees a appointment for service or to order parts through your Tiffin SERIAL NO Motorhomes Dealership or Service Center This number can be found on the side of the dashboard A typical sample of this Figure 2 MIO Seral Number identification label is shown in Figure 1 2 Another label affixed to your Allegro Bay is the Recreational Vehicle Industrial Association RVIA Weight Label Figure 1 3 which is a required label for your vehicle Tiffin Motorhomes a manufacturer member of RVIA has the obligation to disclose the following information at minimum to the purchaser of the motor home 15 e An indication of the contents of the RVIA weight label affixed resrestional vente andusteal association RVIA to the motor home Tiffin Motorhomes Inc e A concise explanation of the following it
184. that scene will be distorted Detailed instructions for these manual adjustments can be found in the manufacturer s literature available in the Owner s Information Package However this brief overview of mirror adjustment can begin the process The top portion of the mirror should be adjusted horizontally so that you can see your own motor home in the one inch surface closest to the motor home the remaining portion of the mirror now permits you to see the road behind you The mirror should be adjusted vertically so that you can see the rear bumper on the bottom of the plane portion of the mirror Figure 9 8 Mirror The convex mirrors should be adjusted horizontally so that you can see your own motor home in 1 3 of the mirror These convex mirrors should then be adjusted vertically to allow you to see any other vehicles alongside your motor home Important Objects viewed in convex mirrors appear smaller and farther away than they actually are 98 INTERIOR FEATURES Chapter Interior Features 10 1 INTERIOR FEATURES Bedspread As a furnished part of the bedroom suite Figure 10 1 a bedspread and matching pillow accessories are included in a d cor compatible with the rest of the motor home Other bedlinens e g sheets blankets pillows pillowcases are the sole responsibility of the motor home owner and are to be provided by that owner For the bedspread and pillow shams cleaning instructions are f
185. the motor home is moving the sleeping facilities are not to be used In the event of an emergency be sure that everyone in the motor home is familiar with all escape exits doors escape window Do not use the emergency window as a routine exit this is strictly to be used for emergency purposes only When the motor home is parked be sure that the emergency exits are not inadvertently blocked Prior to Departure For your continued safety and convenience the following is a representative check list designed to assure your safety while driving Clean all windows mirrors and light lenses front back side to assure that you can see and be seen Reposition any mirrors or other fixtures to provide an unobstructed view front sides and back from the driver s seat see Chapter 9 for details When another driver takes over reposition the mirrors and other fixtures for that driver Remove ot secure all loose fixtures e g awnings flags antennas portable lights to keep them from falling from the motor home when the motor home is in motion Make a walk around visual inspection of the motor home to note any irregularities e g loose trim or problems e g under overinflated tires abrasions or nicks on the tires correct noted problems accordingly Check all exterior storage compartment and generator compartment doors to make sure that they are properly latched and locked If need be check inside all exte
186. the water has a high iron and sulfur content then add one tablespoon of chlorine bleach to every 10 gallons of water in your tank this will precipitate the iron or sulfur so that the filter can remove those impurities If you are at a site where the unit is connected to a city water supply you will not be able to chlorinate the system because the water flows straight to your faucets and not through the freshwater tank Filters should be changed every 6 12 months depending on the quality and quantity of water that is used in your motor home Water Heater Bypass System The water heater bypass valve Figure 11 7 is located in an outside compartment behind the water heater By closing the water heater supply valve and opening the bypass valve one can divert water away from the water heater This process is performed when winterizing your motor home Using the bypass valve will keep antifreeze out of the water heater when winterizing the motor home Draining the water heater during winterizing is a MUST If not properly drained the water heater would be subject to damage from possible freezing thawing cycles To prepare the motor home for reuse switch the bypass valve back to its normal position and re fill the water heater Figure 11 7 Water Heater Bypass Valve Freshwater Lines Vibration and flexing encountered when the motor home is traveling can cause pipes and fittings to become loose Check all of the plumbing connections for leak
187. tion Figure 14 3 Striping amp Decal Important Do not use solvents such as acetone MEK toluene and the like on the decals Any solvent including alcohol may soften and smear colors Do not use lacquer thinner or paint thinner on decals Do not overcoat the decals with clear paint Do not allow gasoline or other fuels to come into prolonged contact with the decals However if this should occur immediately flush the affected area with water 144 ROUTINE MAINTENANCE Important Do not use harsh detergents acids or abrasives which may scratch or dull the surfaces The applicator cloth sponge or soft bristled brush should be non metallic and non abrasive Important Remember to check periodically the tightness of your wheel lug nuts Roof Care and Maintenance Proper care and maintenance of your motor home including your roof is important for sustained trouble free performance Normal maintenance is simple and easy and does not require special materials The roof of the motor home is fiberglass and can be cared for in the conventional manner Keep the roof clean one should clean the roof at least every three months The roof should be professionally inspected by a dealer for leaks Sealant may be necessary in the second year of ownership Warning Use caution when working on the top of your motor home The wet roof may be extremely slippery and as such a possible safety hazard Moisture Management
188. tion turn the vehicle ignition switch off and open the door The step will extend and lock in the DOWN position Caution If the door is opened and closed without allowing the step to extend fully and lock in the DOWN position the step will retract and lock in the UP position When the door is re opened the step will not extend The power switch must be turned on for the step to extend 7 This feature is only operative the first time the door is opened after the vehicle ignition switch is turned off When the ignition switch is on the step will always activate with the door movement regardless of the position of the step power switch Caution Always be sure to look before you leap When opening the entrance door from the inside be sure that the step has fully deployed before trying to step outside to avoid falling and possible injury 97 EXTERIOR FEATURES Mirrors This motor home is equipped with convex remote controlled exterior rear view mirrors Always adjust the mirrors for maximum rear visibility prior to driving If another driver is to drive be sure the mirrors are readjusted to accommodate the second driver These standard black mirrors are adjusted manually The bottom half of each mirror is convex and is also adjusted manually The convex portion of the mirror provides a much wider view of the scene but the apparent size and distance to the objects in
189. tively simple and is considered to be routine maintenance which is the responsibility of the owner 142 ROUTINE MAINTENANCE Important Never use a strong solvent such as lacquer thinner or harsh abrasives on any of the exterior painted surfaces Waxing The exterior finish will require a routine waxing When water will not bead and roll off a freshly washed motor home a new coat of wax is needed Wax not only improves the appearance of the motor home but it also protects the finish against oxidation and corrosive materials The recommended type of wax is one that is compatible with painted and gel coated fiberglass finishes and contains an UV ultra violet inhibitor Buffing with a polishing compound will improve a dull ot discolored finish Important When using a polishing compound that does not contain a wax preservative reapplying a coat of hard wax after polishing is recommended Seals The seals Figure 14 2 around the doors windows vents slide out trim and external seams should be checked at least semiannually Additionally the roof seams should be inspected for cracking or peeling at least annually If any deterioration is noted during a routine maintenance inspection reseal the seams or seals with an approved sealant to prevent any leaks Your Tiffin Motorhomes dealer can perform the resealing inspections and subsequent work if any for you It is recommended that a Tiffin Motorhomes authorized service ce
190. trical power for the 12 VDC system is supplied by the batteries of the Allegro Bay those batteries are in turn charged by a power converter The electrical power for the 120 VAC is supplied by the electrical power hookup cord when the Allegro Bay is connected to an external power source or when the on board electrical generator is in operation Caution Failure to turn off the 120 VAC appliances when starting or stopping the generator may damage the transfer switch and or electrical appliances To connect the Allegro Bay to an external source of 120 VAC electrical power it is first recommended that all of the circuit breakers are in the off position this is done to prevent any power surge upon connecting the motor home to the external power source Then unwind the power cord from the electrical compartment located in the compartment behind the driver s side rear tires The standard flexible power cord supplied with the Allegro Bay is designed to handle up to 50 amperes Make sure that the pins in the male end of the plug are oriented correctly so that they match the power cable and that they are in good condition i e aren t bent or damaged If there is a circuit breaker switch at the plug end of the power cord that breaker should be turned off before making the connection Insert the plug into the mating outlet and then turn the circuit breaker on Close and lock the electrical compartment door to protect the cont
191. uctions DRIVING amp SAFETY INSTRUCTIONS Safety Considerations Prior to using your motor home especially for the first time or after a long period of non use please read thoroughly all the instructions in both the Owner s Manual and the chassis manufacturer s manual before attempting to operate your motor home There are several safety considerations which you should realize and follow while your Allegro Bay is in motion These safety considerations as well as others meant to preclude any damage to the motor home are listed in this chapter Besides the driver it would be helpful for the passengers to be familiar with these safety considerations and precautions too Warning Before your motor home is to be operated be sure that you have read the entire Owner s Manual and that you fully understand the equipment on your motor home and how to use that equipment safely General Warning Warning Any portable fuel burning e g charcoal propane butane wood equipment must not be used inside the motor home Any use of such equipment inside the motor home may readily cause fires and or asphyxiation by carbon monoxide poisoning Further such unauthorized use would probably invalidate your motor home insurance policy In general there are several common sense safety precautions that should be taken every time the motor home is to be used on the road these precautions include e Only seats with seat belts should b
192. valve to the LP tank and turn off all gas appliances and then take the motor home to a qualified service technician after the ventilation process is concluded and the doors and windows again shut Figure 3 5 CO LP Gas Detector 37 MAJOR APPLIANCES ACCESSSORIES Chapter Major Appliances amp Accessories 41 MAJOR APPLIANCES ACCESSORIES Refrigerator The Allegro Bay motor home will contain a refrigerator manufactured by either of these two manufacturers Norcold Incorporated or The Dometic Corporation As each of these operates somewhat differently from the other each will be individually addressed in this section to permit the motor home owner to use the one installed in his motor home Note If the 12V system is off the refrigerator will not work When the refrigerator is in the LP gas mode make sure that the main LP gas valve is in the on position before attempting to start the refrigerator Please note that the refrigerator is equipped with a semi automatic energy selector AES control system which can set automatically to switch between a 120 volt AC system or a LP gas operation system Warning The majority of LP gas appliances used in motor homes normally vent to the outside of the motor home When your motor home may be parked in close proximity to a fuel pump i e during re fueling operations it is possible that the fuel fumes could enter this type of appliance and possibly be ignit
193. ve door Figure 14 9 and align hose end coupling with slots on each side of intake opening Firmly push into intake opening Make sure hose end coupling is connected and is locked in place To disconnect the hose simply push in the slots on each side of the hose coupling and pull hose end straight out 14 28 ROUTINE MAINTENANCE To start the vacuum cleaner 1 Push the on off switch on the main vacuum to the on position Indicator light in switch will come on Now the vacuum will come on and off by using the wall remote inlet valve 2 To turn on raise the door up 3 To turn off lower the inlet valve door down and the vacuum will turn off The main vacuum on off switch should stay in the on position all the time except when traveling 4 To turn completely off return main vacuum on off switch to the off position The switch light will go off Warning This appliance has a THERMAL PROTECTOR built in the motor to prevent overheating If motor will not operate or shuts down while in operation wait 30 minutes it will reset automatically Turn unit off while it resets If the motor does not come on or Thermal Protector trips off again after a short period service may be needed A qualified service technician should perform service The vacuum cleaning system comes with an array of attachments that can be connected to the hose ends for extensive cleaning purposes Make sure they are firmly pushed in and twist to
194. ver pressure and over temperature conditions is located on the exterior of the water heater This valve will operate if the water temperature reaches or exceeds 210 F or if the water pressure reaches or exceeds 150 psig Since the water system in the motor home is a closed system when all water valves are shut the water heating cycle can raise the temperature and consequently the pressure of the water in the water heater thereby realizing pressure increases approaching 150 psig Should this pressure be reached the pressure relief valve will begin weeping that is minor dripping or leakage from that valve until the pressure drops below 150 psig at which time the pressure telief valve will re seat itself and restrict the water flow This is normal operation and should not be a cause for alarm Do not obstruct or block the pressure relief valve in any way as this would keep the valve from functioning normally and protecting the hot water system CB Radio System Antenna Connection The Allegro Bay comes equipped with an antenna and coaxial cable connection Figure 4 18 to enable the owner to install a Citizens Band CB radio of choice and operate it conveniently from the Allegro Bay The coaxial cable connection for the radio is found beneath the dashboard on the driver s side Accordingly with an owner provided CB radio that radio can be used to communicate with other travelers on the road To use the one s CB system of choice
195. whenever the motor home is used to keep the leveling system in good operating condition Electric Steps The Allegro Bay is equipped with electric three step doorsteps As such the switch Figure 9 6 to operate these steps is located in the passenger console box When the power switch for the steps is in the on position simply open the door and the steps will automatically extend Detailed operation for the electrical three Figure 9 6 Electric Steps Switch on left step door steps is as follows 1 Turn the step power switch on 2 When closing the door the step should retract and lock into the UP position When opening the door the steps Figure 9 7 should extend and lock into the DOWN position 3 Turn the step power switch off The step should remain in an extended position when the door is closed Turning off the power with the step retracted will hold the step in a retracted 4 position as well Figure 9 7 Electric Steps 96 EXTERIOR FEATURES 5 With the step extended turn the step power switch off and close the entrance door Turn the vehicle ignition switch on The ignition override system will go into effect and the step will automatically retract Caution If the motor home is driven with the step in the extended position there is the possibility of causing major damage to both the step and the motor home 6 With the step switch in the on posi
196. y located to support the areas of concern Construction of these cabinets incorporates various hardwoods raised panels cabinet doors and supports Door pulls handles and knobs are installed in a style complementing the particular d cor of each Allegro Bay so that an aesthetically pleasing as well as fully functional storage capacity is realized For the many floor plans available in the Allegro Bay product line cabinet design has been optimized to provide maximal storage for each and every floor plan available Accordingly the Allegro Bay can readily accommodate the routine materials supplies and customer specific items desired for any travel requirements Figure 5 1 Representative Cabinetry in the Motor Home Further these cabinets are designed to contain stored supplies quite securely during travel to minimize or eliminate the possibility of shifting or spilling of cabinet contents during travel Yet when the motor home is parked all stored items ate readily available in the cabinets for the convenience of the users As the storage requirements will vary somewhat from one floor A plan to another general observations can be made about the l Tiffin supplied cabinetry which may or may not be applicable for your specific Allegro Bay configuration Figure 5 2 Countertop Cabinets are provided in the kitchen dining area to accommodate the routine cooking utensils and groceries normally desired for travel Storag

Allegro Bay Owner`s Manual

Contents

Download Pdf Manuals

Related Search

Related Contents