User`s Manual
Contents
1. 61000 3 for CE certification These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction guide may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Re orient or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult a service representative for help Properly shielded and grounded cables and connectors must be used in order to comply with FCC CE emission limits Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment 1 9 Regulatory Statements 2012 Opticis Co Ltd All Rights Reserved Revision 1 0 Mar 22 2012 Opticis Locations Headquarters Opticis Co Ltd 907 Byucksan Technopia 434 6 Sangdaewon Dong Chungwon Gu2. Sungnam City Gyeonggi Do 462 716 South Korea Tel 82 31 737 8033 8 Fax 82 31 737 8079 www opticis com For order support please contact your Distributor or Reseller For technical support check with the Opticis web site www opticis com or contact techsupp opticis com
3. Jack Core is 5 V and outer is GND 1 7 Product Specifications Warranty Information 1 One Year Warranty Opticis warrants this optical DVI extension module to be free from defects in workmanship and materials under normal use and service for a period of one 1 year from the date of purchase from Opticis or its authorized resellers If a product does not work as warranted during the applicable warranty period Opticis shall at its option and expense repair the defective product or part deliver to customer an equivalent product or part to replace the defective item or refund to customer the purchase price paid for the defective product All products that are replaced will become the property of Opticis Replacement products may be new or reconditioned Any replaced or repaired product or part has a ninety 90 day warranty or the reminder of the initial warranty period whichever is longer Opticis shall not be responsible for any software firmware information or me mory data of customer contained in stored on or integrated with any product s returned to Opticis for repair under warranty or not Warranty Limitation and Exclusion Opticis shall have no further obligation under the foregoing limited warranty if the product has been damaged due to abuse misuse neglect accident unusual physical or electrical stress unauthorized modifications tampering alterations or service other than by Opticis or its authorized agent
4. Manual Contents p i IC S Manual Contents 1 0 www opticis com Welcome Product Description 1 1 System Requirements for Setup 1 2 Installation 1 3 Self EDID Programming Procedure 1 5 Troubleshooting Maintenance Technical Support 1 6 Product Specifications 1 7 2 Fiber Detachable Warranty Information 1 8 Dual Link DVI module Regulatory Statements 1 9 D D FX 1 00 Pictorials Figure 1 Connection Diagram of Optical DVI Extension Modules 1 1 User s Man ual Figure 2 Fiber numbering and Status LED position on a label 1 3 Figure 3 Connection of optical fiber 1 4 Figure 4 Position of EDID PRG Button and Status LED 1 5 Welcome Congratulations on your purchase of the Stretch DVI DDFX 100 TR Optical Dual Link DVI Digital Visual Interface Extension Module This manual contains information that will assist you in installing and operating the product Product Description The DDFX 100 TR optical DVI module transmits uncompressed WQXGA 2560x1600 60Hz or WQUXGA 3840x2400 33Hz vertical refresh rate of Dual link DVI up to 500 meters 1640feet over two 2 LC multi mode fibers The EDID Extended Display Identification Data in a display can be read and restored by just plugging once transmitter to the display This Self EDID programming feature makes the installation of DDFX 100 TR more easy and flexile at any variable resolution display systems For your convenience WQxXGA EDID had been stored be
5. and it indicates completion of all procedure Step 5 Disconnect the transmitter from the display 1 5 Self EDID Programming Procedure Troubleshooting The display shows only black screen Ensure that all plugs and jacks used by external power supplies both Opticis and others are firmly connected Ensure that the Power and status LED ON Ensure that the DVI ports are firmly plugged in to the PC and display Ensure that the transmitter and receiver modules plugged correctly to the PC and display respectively Check if the PC and display are powered on and properly booted Reset the system by de plugging and re plugging the transmitter DVI port or receiver DVI port or by de plugging and re plugging the power plugs of transmitter and receiver modules Re boot up the system while connecting the optical DVI extension module Screen is distorted or displays noises Check if the graphic resolution is properly set Go to the display properties of Windows and tap the settings Ensure that the resolution sets less than WQUXGA 3840x2400 at 33Hz refresh ratio Reset the system Disconnect and reconnect the optical DVI cables or 5V power adapters Maintenance No special maintenance is required for the optical DVI module and power adapters Ensure that the DVI modules and power adapters are stored or used in a benign environment free from liquid or dirt contamination There are no user serviceable parts Ref
6. er all service and repair issues to Opticis Technical Support and Service For commercial or general product support contact your reseller For technical service contact Opticis by email techsupp opticis com or visit its website at www opticis com 1 6 Troubleshooting Maintenance Technical Support Product Specifications DDFX 100 TR Optical DVI Extension Modules O Compliance with DVI standard Supports DVI1 0 fully implemented by fiber optic communication and DDC2B by virtual DDC O Extension limit 500 meters 1640 feet for WQUXGA 3840x2400 at 33Hz refresh rate O Graphic transmission bandwidth Supports up to WQUXGA 33Hz or 1 65Gbps bandwidth per graphic channel O Supporting resolution Based on DVI input HDTV 480p 720p 1080p VESA VGA SVGA XGA WXGA SXGA WXGA UXGA WSXGA WUXGA WQXGA Default WQUXGA O Fiber optic connection The transmitter and receiver modules of DDFX 100 have two 2 LC receptacles so as to be connected with two 2 LC multi mode fibers having 62 5 50 125um core DDC connection Virtual DDC by Self EDID programming O Mechanical specifications of transmitter and receiver modules m Dimensions 39mm x 72mm x 15mm W D H O Environmental Specifications E Operating temperature 0 C to 50 C Storage temperature 30 C to 70 C m Humidity 0 to 85 AC DC Power Adapier O Power Input AC 100 240V 50 60Hz 0 1A O Power Output 5 V 1A SMPS DC power Adapter O Cord DC
7. fore shipment as a default Shipping Group O DDFX 100 TR Optical Dual Link DVI Extension Module One 1 pair AC DC power adapter Two 2 units of 5V 1A User s Manual O Option Product Duplex LC Patch Cord Multi mode fiber Up to 500m at WQUXGA 3840x2400 33Hz ing DDFX 100 2 o Is Pij Tx g lioa 7 B be DDFX 100 Rx Dual link DVI Source Dual link DVI Display Figure 1 Connection Diagram of Optical DVI Extension Module 1 1 Welcome Product Description System Requirements for Setup O Hardware requirements m You have to have a DVI graphic controller or card having a DVI port in your PC SUN or Mac systems It should support the maximum graphic resolution feature of displays to be connected No special requirements for memory size CPU speed and chipsets if you ve already properly installed your DVI graphic controllers or cards O Software requirements m No special restrictions if you ve already properly installed your DVI graphic controller in your OS O AC DC Power Adapter Technical Advisory The transmitter Tx module of DDFX 100 TR is designed for power protection circuit from conflict of power supply between the external AC DC power adapter and your DVI source by 14 pin We strongly recommend to use external AC DC adapter for Transmitter Tx for stable power supplying In case of Receiver Rx power should be supplied by AC DC adapter due to no internal p
8. n them to avoid undesirable performance degradation Step 6 Make the PC and the display power ON And ensure that the Status LED in transmitter and receiver turn on 1 4 Installation Self EDID Programming Procedure The graphic source equipment generally requires display information EDID It contains resolution and timing information of the display DDFX 100 TR supports Self EDID programming It is the procedure that reads the EDID from the display and stores it in the EEPROM of the transmitter You have to do Self EDID programming if the maximum resolution of the user s display is not WQXGA 2560x1600 Follow the steps below to do it correctly Note1 If you know that EDID is not required by the user s DVI source Self EDID programming is not necessary Note2 The default EDID in factory ship out is programmed in the VESA standard of WQXGA 2560x1600 60Hz Step 1 Power on the display Step 2 Plug the 5V power adapter to the power jack of the transmitter of DDFX 100 Ensure the Power LED is ON Step 3 Push the EDID PRGM button of the transmitter with a narrow pin Then status LED will be turned ON y EDID Programming button A Figure 4 Position of EDID Programming button Step 4 Connect the transmitter to the display not to the PC Then the status LED will begin to blink rapidly It indicates reading the EDID from the display and storing it in the EEPROM After 7 8 sec the status LED will be turned ON
9. ower supplying from the displays 1 2 System Requirements for Setup Installation Important Please keep the installation procedure below Improper or no operation may result if the start up sequence is not correctly followed Step 1 Carefully unpack the contents of the shipping group Step 2 Plug the 5V power adapters to the power jack of the transmitter and receiver Ensure the Power LED ON Blue and Status LED blinking slowly Blue Step 3 Please check if the maximum resolution of the display is WQXGA 2560x1200 Otherwise follow the instructions for Self EDID Programming Procedure on page 1 5 Step 4 Connect two 2 LC optical fibers between the transmitter and the receiver and each fiber channel shall be connected as 1 to 1 and 2 to 2 carefully and ensure the duplex connectors are fully engaged cis Status cis Status Stretch DVI Stretch DVI DDFX 100 DDFX 100 Dual Link TX Dual Link RX Susa 2 2 Sanam 2 1 Figure 2 Fiber numbering and Status LED position on a label 1 3 Installation Step 5 Plug the transmitter to the DVI receptacle of the DVI source such as PC and the receiver to the DVI receptacle of the display as shown in figure 3 iy DDFX 100 Bio See 4 Ie gt ay DDFX 100 Rx Figure 3 Connection of optical fiber Note1 The maximum extension length by multi mode fiber is 500 meters Note2 Be recommended NOT to use any intermediate cable or adapter betwee
10. s causes other than from ordinary use or failure to properly use the product in the application for which said product is intended Dispose of Old Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate systems This symbol on the product or on its packaging indicates that this product shall not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative Eoo consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The recycling of materials will help to conserve natural resources For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product 1 8 Warranty Information Regulatory Statements This device complies with part 15 of FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 and 2 of FCC Rules EN 55022 55024
Download Pdf Manuals
Related Search