BTT-2 SPEAKER TOWER WITH BLUETOOTH®, FM RADIO
Contents
1. 2 Search for stations with a lower frequency by holding the previous button on the device or the tune on the remote control for 3 seconds lf needed manual tuning can be used to fine tune to a station Searching for a radio station by program type The Program Type function abbreviated PTY function allows you to search for a Station that is broadcasting a specific genre for instance classical music When the PTY function is activated the search function will stop only at stations that belong to the set category of the PTY function If for instance classical music has been set then the search function will not stop at a station that only plays rock music Activate the PTY function by holding the PTY button on the remote control until a genre appears on the display Then repeatedly press the PTY button until the desired genre is shown on the display Then press the tune button on the remote control to search for this genre If needed manual tuning can be used to fine tune to a station Saving a radio frequency You can save up to 20 preset stations in the memory of this device Tune to the frequency that you would like to save and follow the steps below to save the frequency 1 Press the store button on the remote control the preset number appears on the display 2 The preset number can be increased by pressing M on the remote control and decreased by pressing M on the remote control 3 Press the store button on the remote co2. 6 Stop button press this button to stop playback 7 Volume knob turn this knob clockwise to increase the volume or counterclockwise to decrease the volume 8 LCD display the LCD display displays the most important information 9 Modus button press this button to switch between the Bluetooth AUX FM SD and USB mode 10 Standby button press this button to turn the device on or press the button to switch to standby mode 11 Pair button when the device is in Bluetooth mode press this button to reconnect with another device 12 Mute button press this button to mute the speakers Press this button again to unmute the speakers 13 SD card slot insert an SD card in this slot 14 USB port insert a USB storage device in this port WARNING Do not use a USB extension cable to connect a USB device The use of a USB extension cable can cause malfunction or loss of data 15 AUX INPUT connect a device that is equipped with an AUX output or headphones output to this input 16 Wire antenna the antenna receives the FM radio signals 17 Power on off switch set the switch in the OFF position to switch off the device Set the switch in the ON position to put the device in standby mode 18 AC connection connect the power cord to this connection 1314 15 15 Exploring the remote control OooolY OIC 1 Function button press this button to switch between the Bluetooth AUX FM SD and USB mode 2 Info button
3. in the FM mode RDS information is shown on the display Press this button to show the frequency and PTY information on the display 3 Sleep button press this button to display sleep timer information set the sleep timer or turn off the sleep timer 4 Previous rewind button press this button to skip to the previous song hold the button to search backward in the track 5 Next fast forward button press this button to skip to the next track or hold the button to search forward in the track 6 M button only works in radio mode Use this button to save a preset station or recall a preset station 7 Tune button only works in radio mode Use this button to change the radio frequency 8 Store button only works in radio mode Use this button to save a station 9 Numeric buttons use these buttons to input digits 10 Repeat button only works in SD amp USB mode Press this button to repeat a track folder or all tracks on the media 11 Volume button press this button to decrease the volume 12 Standby button press this button to turn on the device or put the device in standby mode 13 Mute button press this button to mute the speakers Press this button again to unmute the speakers 14 Play pause button press this button to pause or resume playback 15 Stop button press this button to stop playback 16 Tune button only works in radio mode Use this button to change the radio frequency 17 M button only
4. Class II construction can be connected to an unearthed power outlet The power outlet must be located close the device and must be easily accessible Make sure that power outlets or extension cables are not over overloaded Overloading can cause short circuits or fire Always pull the plug when removing it from the power outlet Do not pull the power cord This may cause a short circuit f you notice smoke an excessive build up of heat or any other unexpected phenomena you should disconnect the plug from the power outlet immediately Disconnect the plug from the power outlet during lightning storms Disconnect the plug from the outlet when the device will not be used for a long time Do not step on the power cord and don t pinch the power cord Do not place heavy objects on the power cord or any other cables as this may damage the cord or cables Keep the device away from children When they play with the power cord they can seriously injure themselves Keep the power cable away from rodents and rabbits These animals like biting in cables Make sure all ventilation openings are clear at all times do not cover or block them Leave 5 cm 2 free space around the device Always make sure the device is well ventilated Keep the device away from heat sources such as radiators heaters stoves candles and other heat generating products Avoid using the device near strong magnetic fields Do not use this device w
5. REP ONE when this is shown on the display the current track will be repeated continuously REP DIR this is shown on the display when all tracks in the current folder are repeated This function can only be used when the tracks are stored into 1 or multiple folders REP ALL if this is shown on the display all tracks on the storage media will be repeated REP OFF when this is shown on the display the repeat function is disabled and all tracks will be played normally Advanced Display information Press the info button on the remote control to display extra information The information that is shown on the display depends on the mode and media that is being played Sleep timer This device is equipped with a sleep timer that can be used to turn off the device after a preset amount of time has elapsed Press the SLEEP button on the remote control to set the sleep timer Once the button is pressed the display will show the sleep time the time in minutes after which the device will be turned off When the sleep timer is already active the remaining sleep time is shown on the display Repeatedly press the SLEEP button on the remote control to adjust the sleep time You can also do this when the sleep timer is already activated and you want to adjust or disable the sleep timer The sleep timer is disabled when the display shows OFF Adjusting the audio setting Via the audio settings it is possible to adjust the high and low to
6. ELNE GU LIA ED D ILE EC 35 Declaration Go ae dni TERT 35 Serviced SUDDO ari 36 Do not distribute copyrighted material oocccoccococnconcnnoonccncncnnnnnnnnnnncnnnnnonnnncnnrnnnanonos 37 a Bice MH c EET 37 BASA A A A IR 38 Dear customer This device allows you to listen to radio stream Bluetooth audio to this device and playback audio from a USB storage device SD card of via the AUX input Thank you for choosing for Lenco At Lenco we are convinced that everyone should enjoy life as much as possible Our products are meant to support improve and create joyful moments for everyone For this reason we offer user friendly high quality and well designed consumer electronics for an excellent price This user manual is designed to help you with the features of this device Please keep this manual for future reference This user manual was written during the development of the product based on the factory settings If the product would need improvement priority is given to the product and therefore in these cases the quick start guide user manual illustrations in the user manual and or packaging may differ from the actual product What s in the box The content of the box is assembled with the utmost care In the unfortunate case that anything is missing please contact your dealer Content of the box 1 Speaker tower 1 Base 1 Remote contro 4 Mounting screws 1 Power cord 1 Quick start guide Explanat
7. LE THROUGH THIS DEVICE UNDER NO CIRCUMSTANCES INCLUDING NEGLIGENCE SHALL LENCO BE LIABLE NEITHER IN CONTRACT NOR TORT FOR ANY DIRECT INDIRECT INCIDENTAL SPECIAL OR CONSEQUENTIAL DAMAGES ATTORNEY FEES EXPENSES OR ANY OTHER DAMAGES ARISING OUT OF OR IN CONNECTION WITH ANY INFORMATION CONTAINED IN OR AS A RESULT OF THE USE OF ANY CONTENT OR SERVICE BY YOU OR ANY THIRD PARTY EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES Third party services may be terminated or interrupted at any time and Lenco makes no representation or warranty that any content or service will remain available for any period Content and services are transmitted by third parties by means of networks and transmission facilities over which Lenco has no control Without limiting the generality of this disclaimer Lenco expressly disclaims any responsibility or liability for any interruption or suspension of any content or service made available through this device Lenco is neither responsible nor liable for customer service related to the content and services Any question or request for service relating to the content or services should be made directly to the respective content and service providers 2012 STL Group B V all rights reserved Lenco is a trademark of STL Group B V STL Group B V is not responsible for any printing errors in this manual Products of other manufacturers are only mentioned for information This does not mean that these products are
8. Lenco IMPORTANT INFORMATION Checking the model number Before you get stared please make sure the right user manual is included and it belongs to your device This user manual is only intended for the Lenco BTT 2 You can find the model number on the packaging or on the specification plate on the back of the device f J Be Table of contents Checking the model nuMber cococccccccccccccncocccnnononnnonnnnononononnnnnonanononaronnnnnnnnnnnnnnenenoss 2 Table Of contents oocccccccccnccocncocncocncnononocnnnnnonononncnonnnononnnnnnnnnnnnnnnnnnnnnnnnannnnrnnnnnenaninas 3 A sott ptenbE Em tx Mim fap Apc UNS M Fe xU ND NODE 6 Explamdgonm orte SVITDOIS errata tati icu EE de 7 Important information before using the AeviCe occoocccoccccocccocncnonocncnnncnonanonaronncnonanonas 7 Unpacking the device cccooccccoccccocnccocnconcnccnnncnnnnonnnnnonnnnonnnnnnnnnnnnnnnnnnnonnnnennnnenannnnos 8 What to do with the packaging malterial occcoccococnccccncoonccncncnanononnnoncnonanonnnnconcnnnanonos 8 Moun ng TNC DAS Nr aii 9 Exploring the device ccccccccsseecseeecseeecseeecsueecsueecseecseessucessusecsueessusecsueessueesseeeeas 10 Exploring the remote CONTO NT n 12 WAGTE TO MSTA AA APP ene ee en ee 13 Mounting the FM wire antenna cccccceccceecceeeeseeeeeeeeeeeeseeeseueeseeeseeesauessueeneeeseeeeags 14 Connecting the device to a power supply ccooccc
9. Pausing playback During playback press the play pause knop on the device or the remote control to pause playback press the button once more to resume playback Skipping to the next track During playback of an audio file press the next button on the device or the remote control to skip to the next track Searching forward During the playback of an audio file hold the next button on the device or the remote control The device will search forward in the track until the button is released Skipping to the previous track During playback of an audio file press the previous button on the device or the remote control to skip to the previous track Searching backward During the playback of an audio file hold the previous button on the device or the remote control The device will search backward in the track until the button is released Stopping playback Press the stop button on the device or the remote control to stop playback Playing the content on the storage media in random order Press the RAN button on the remote control to enable or disable the random mode When the random mode is active tracks will be played in random order When the display shows RAN OFF the random mode is switched off When the display shows RAN ON the random mode is switched on Repeating the content on the storage media Press the REPEAT button on the remote control to enable or disable the repeat function This device has various repeat functions
10. R TT 18 AUX aM ersten ae aes oss nee duonico cuida dude quico oceano 18 Connecting an AUX device cccccseeecccecceeeeeeeeecaeeeeeeeecaeeeeeeeseeeeeeeeeeseaseeeeesseaeeeeesseaseeeeesaaeeeeeeeeas 19 A O 19 Manu Artum aria ETT D TI ERES 19 AUTOMA NC TUN O iaa ota aciieaidha 19 Searching for a radio station by program tyPe ccccccseeeeceeceeeeeeeeeeeaeeeeeeeeseeeseeeeeseeaeeeeeessaeseeseeeas 20 Saving AGIO WEQWENCY EE IT EM 20 Recalling adqresebstatioD oo 20 Switching between mono and stereo essssssesssssssssese nennen nennen nnne annia nnn nnn 20 BG APOC aha wn hairs I DIS a A A 20 Pasing Play Dacia MEE 21 SKIPPING to Nene lack o TRE 21 Sep V rz ro NA ce 21 SKIPPING io the DEVIOUS WACK outta obe up at dead oia bot 21 searching DACKWANG odes er oan tuno e Oeo Me ha etu eap re ae le ento aud ede a Datus ot 21 StOppina PlayD IC eomm 21 Playing the content on the storage media in random Ol F o ooccnccconcnncccnccnconnncnncnnncnnonnnnonconanenoss 21 Repeating the content on the storage Media ccccocncccccncnncoconnnnoconcnnnnnanonconannncononcnnonnnnanennnnaness 21 USB MOS TTE 22 PAUSINI iaa 22 SKIPPING OTHE META alada 22 Se Ro AAA SNO M a eee eee ee ee eee 22 SKIPPING to ThE previous WACK aiii 22 SECANO TONNO a ios 23 SLOP PIITG OlAY WACK setae eects ns Sas 23 Playing the content on the storage media in random Ord6r occcccocccccccnncccnnnccncncnnncncnnncn
11. a barely be heard because of hiss Increase the distance between the device and other equipment Place the Bluetooth device closer to Bluetooth music stutters the radio Check the input source Keep the remote control closer to the device Check the batteries and replace if needed Aim the remote control directly on the remote control sensor on the front of the device The format of the files is not supported The SD card or the USB device is not compatible with the device try using a The remote control does not work The SD USB media does not play different SD card or USB device Specifications Power Supply AC 100 240V 50 60Hz 1 5M euro plug Standby isla cl oae 35 C Operation Humidity 1 595 9096 90 Maximum elevation above sea level 10 000 meters 10 50 C Humidity 596079096 UMN SOAGE Maximum elevation above sea level 10 000 meter Output Speaker max 90 Watt RMS Subwoofer Frequency Response 20Hz 16KHz MS 10 Adjustable Bass Treble _ Bass Treble FM FMband 1 87 5MHz 108MHz opeaker Tower incl base 90 x 29 x 29 cm EEE SUAE Hemote Control 11x5x2cm Main device incl base 7 5 KG Remote Control Display Color Information etme 07 T E Remote Control Hange Em of m Battery 2X AAA 1 5V LIC NE 2 0 5V 500mA R Tot32GBB_ eol M CHE 999 999 files 99 folders 99 folders Coneco External Audio Input Line in RCA cinch Up to 32GB SD Memo
12. ccoccnccoccnccononoconononacononanncnnnnnononens 15 Stopping the device in an emergency ccseccceeccceecceeccceeeceucecueeceeecsueecsuessueessueeeeeessueess 15 Connecting the device to the mains c ooccccccncccccnccncnncnnnnnononnnoncnnnnnnnnnnnncnnnnnnnncncnnnnonenennnos 16 General information about the energy saving mode ccooccccccnccncnccncnccncnnoncnconcncnnnnnonons 17 z epejem 17 e r Jaizigziejor Ez iON MENTRE EM 17 Turning the power on or off on the device ccccooccncccccnnccoconcnnononcnnnnonnnononanonnnnonnnnnnnnnnnnonanennnnonens 17 Turning the device on from standby mode cccccsssssececcceeeeeeecccueeeeeeeeeuaueeeeecseaueeeeessaaeeeeeessaaees 17 Putting the device in standby mode essssessssssseeeee nennen nnne nnn nnns nnn nnns 17 Adjusting the speaker VOIUMEC ccccccsssseecccceseececcceeeeceesceaueeeeeesaaaueeeeseuaaseeessseaeeeeessuaeeeeeesaaaass 17 Muting the SO CAK CIS M METTE EE ERR 17 Selecting the input SOU D asmrsooe robarse caos 17 o a 17 Connecting with a Bluetooth device ccccooccnnnccnncccconooonnccnnnnnnonnnanncnonnnononnnnnncnnnnnononnnnnnennnnnnns 17 Paying am Audio Me cias 18 PUSO DIa VDA En 18 SOKIODING TO o Se 18 SECANG TOWA O ssie e i E EEN 18 Skipping to the previous trACk ccccccccccsssseccccceeseeceecceeeeceeeceeeeeeeseeauseceesseeeeeeeseeegeeeeessageeeeesaas 18 pedo o A aE ne Aia 18 o ACE MEE
13. cnnncnnnns 23 Repeating the content on the storage Media occccccoccnnccconcncoconcnncnnnnnnnonanoncnnanennonnnrnnonnnnnnnonaneness 23 o CO Me T EIE 23 Display MTOR MAO NETTE 23 SEDUM aepo ME IM MEI Siete eer IU ee me EI IM LU 23 Adjusting the audio settings ooccoccncconnoconncnonocannnnonononnonnnnonnnonnrnnnnnnonnnonannonnnonarnnnanenos 24 Heseltling thie devibe a ate Dune bie tati ee Coetu ubt aac i s CU e bd eue pee 24 NVM UC We E vanes rr 24 Breaking down the COVICE ccccsecccssceceececeuceceucecsusecsucecsusessueessusessusecsueessueessaeenas 25 Storing and transporting the device ooccccoccncccccncccncnccononoconononanononannnonnnnononcnnnonens 28 miziefe acces son Sinarcas 29 A eo 29 Open Standard erisso 29 TED ali 29 SEIS ON A PP staat tenteuboseendade nenanttedeaueade deoduclaecedetesaecette I 29 LOD PP H 29 USB STCK qu deccieie eaie tiie E a a a pceucate Senettls P 29 LO dev propr 30 Flash MOMO a dc 30 A eee eee er ee eee err eee 30 AUX a Rn a ae ee eee ner ee ee 30 e A tad ies ia ded i cate I tad 30 A Tae eh 1 sc ae eh ak at el Dl as oa 30 jl lm o 30 B ieiliel ciolisjeme t T E 31 DDC CIIC ANIONS o eueqi anion P Dur PEU u EDENDUM UP EU T UDUEE EFI UE Ea gU XN OSEE TOANE 32 Sdiely FrecautofliS sets A 33 NOUce Statements ANG INIOFMALION acce putUu eu puo Mu eU S Ev EO IM D DU SREE SU E
14. d disposal of electrical waste Waste Electrical and Electronic Equipment Directive Service and support For information www lenco com For support http lencosupport zendesk com Lenco helpdesk Germany 0900 1520530 Local charges The Netherlands 0900 23553626 Local charges 1ct p min Belgium 02 6200115 Local charges France 0333 81484280 Local charges France email sSav logydis com The helpdesk is accessible from Monday till Friday from 9 AM till 6 PM When contacting Lenco you will always be asked for the model and serial number of your product The serial number can be found on the back of the device Please write down the serial number below Model BTT 2 Serial number Lenco offers service and warranty in accordance to European law which means that in case of repairs both during and after the warranty period you should contact your local dealer Important note It is not possible to send products that need repairs to Lenco directly Important note If this unit is opened or accessed by a non official service center in any way the warranty expires This device is not suitable for professional use In case of professional use all warranty obligations of the manufacturer will be voided Do not distribute copyrighted material Do not distribute copyrighted material without the permission of the owners By doing this you risk violation of copyright laws The manufacturer is not liable for any legal issu
15. d the previous button on the device or the remote control The device will search backward in the track until the button is released Stopping playback Press the stop button on the device or the remote control to stop playback Playing the content on the storage media in random order Press the RAN button on the remote control to enable or disable the random mode When the random mode is active tracks will be played in random order When the display shows RAN OFF the random mode is switched off When the display shows RAN ON the random mode is switched on Repeating the content on the storage media Press the REPEAT button on the remote control to enable or disable the repeat function This device has various repeat functions REP ONE when this is shown on the display the current track will be repeated continuously REP DIR this is shown on the display when all tracks in the current folder are repeated This function can only be used when the tracks are stored into 1 or multiple folders REP ALL if this is shown on the display all tracks on the storage media will be repeated REP OFF when this is shown on the display the repeat function is disabled and all tracks will be played normally USB Mode Put the device in USB mode and insert the USB storage device The device will start reading the USB storage device Once the USB storage device is read the device will automatically start playing the files on the card
16. device number 16 to see where the wire antenna can be found exactly Extend the wire antenna for the best results we recommend hanging the wire antenna as high and as close as possible near a window Connecting the device to a power supply The operations in this chapter should not be performed by children Before connecting the device to the mains make sure that the mains voltage corresponds to the voltage that is suitable for the device The information about a suitable mains voltage can be found in the specification table If you are unsure about the mains voltage at your current location please contact the utility company Make sure the outlet to which the device is connected is easily accessible Before connecting the device please make sure that the main power switch on the back of the device is in the OFF position If you cannot find the switch please check the section Exploring the device number 17 to see where this switch can be found Do not touch the metal parts of the power cable because there is a risk of shocks with personal injury e A A A A Stopping the device in an emergency In fail situations it might be needed to have the device make an emergency stop For instance when smoke or a strange smell is coming out of the device when the device is making a strange noise etc You can stop the device in emergencies by Disconnecting the power cord from the outlet Always pull the plug o
17. e can cause malfunction or loss of data Notice statements and information Lenco is not liable for printing errors in the manual Declaration of Conformity Products with a CE marking comply with the EMC directive 2004 108 EC and the Low Voltage Directive 2006 95 EC issued by the European Commission of the European Community When you see a crossed out wheeled waste container on the product it means that the product is subject to the EU directive 2002 96 EC This symbol indicates that the relevant electrical product or battery should not be disposed of as general household waste in Europe To ensure the correct waste treatment of the product and battery please dispose them in accordance to any applicable local laws of requirement for disposal of electrical equipment or batteries By doing so you will help to conserve natural resources and improve standards of environmental protection in treatment and disposal of electrical waste Waste Electrical and Electronic Equipment Directive l Dx This product contains batteries that may not be disposed of as general household waste according to the European directive 2006 66 EG To ensure the correct waste treatment of the product and battery please dispose them in accordance to any applicable local laws of requirement for disposal of electrical equipment or batteries By doing so you will help to conserve natural resources and improve standards of environmental protection in treatment an
18. e or the remote control The device will search backward in the track until the button is released Stop playback Press the stop button on the device or the remote control to stop playback AUX Mode Put the device in AUX mode When the device is in the AUX mode the volume can only be controlled via the tower speaker All other controls should be used on the external device Connecting an AUX device The AUX input allows you to connect any device that is equipped with an AUX output or a headphones output The cables that are required to connect these external devices are not included with this product The AUX input can be found on the back of the device FM Radio mode Put the device in radio mode Manual tuning The display shows the current frequency You can search for the desired frequency in 2 ways 1 Increase the frequency with steps of 0 05 MHz by pressing the next button on the device or the tune on the remote control 2 Lower the frequency with steps of 0 05 MHz by pressing the previous button on the device or the tune on the remote control Automatic tuning The display shows the current frequency When the device finds a station with sufficient signal strength the device will automatically stop searching You can automatically search for a station in 2 ways 1 Search for stations with a higher frequency by holding the next button on the device or the tune on the remote control for 3 seconds
19. es caused by illegal use of copyrighted material by the user Trademarks Lenco and the Lenco logo are trademarks of STL Group BV Pair amp Play is a trademark of STL Group BV Pal 2 r W Play logo is a trademark of STL Group BV Bluetooth and the Bluetooth logo are trademarks of Bluetooth SIG Inc Disclaimer some content and services accessible through this device belong to third parties and are protected by copyright patent trademark and or other intellectual property laws Such content and services are solely provided for your personal and non commercial use You may not use any content or services in a manner that has not been authorized by the content owner or service provider Without limiting the foregoing unless expressly authorized by the applicable content owner or service provider you may not modify copy republish upload post transmit translate sell or create derivative works exploit or distribute in any manner or medium any content or services displayed through this device THIRD PARTY CONTENT AND SERVICES ARE PROVIDED AS IS LENCO DOES NOT WARRANT CONTENT OR SERVICES SO PROVIDED NEITHER EXPRESSLY NOR IMPLIED FOR ANY PURPOSE LENCO EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE LENCO DOES NOT GUARANTEE THE ACCURACY VALIDITY TIMELINESS LEGALITY OR COMPLETENESS OF ANY CONTENT OR SERVICE MADE AVAILAB
20. f the power cord never the cord itself l the outlet is not accessible go to the meter cupboard and switch off the corresponding group or the ground fault circuit breaker When a fail situation has occurred make sure to contact your dealer or the Lenco helpdesk before using the device again Explain to the employee what happened the employee will then advise you whether it s wise to start using the device again Connecting the device to the mains Fully extend the power cord and connect the narrow end to the back of the device and connect the wide end of the power cord to the power outlet Preparing the remote control Remove the battery cover and insert 2 A brand AAA UM4 1 5V batteries Make sure that the batteries are placed in the right direction into the remote control the and the side After the batteries are placed place the battery cover back Please remove the batteries from the remote control when it s not being used for a long time General information about the energy saving mode This device is equipped with an energy saving mode This means that when the device doesn t receive any signal for 10 minutes think of no Bluetooth connection song has been paused for a long time etc it switches itself off Basic operation General operation Turning the power on or off on the device To power the device put the switch on the back of the device in the ON position The device will now switch to t
21. he standby mode To turn off the power put the switch on the back of the device in the OFF position Turning the device on from standby mode When the device is in standby mode press the standby button on the device or the remote control to turn the device on Putting the device in standby mode When the device is turned on press the standby button on the device or the remote control to put the device in the standby mode Adjusting the speaker volume Turn the volume knob to adjust the speaker volume Turn counterclockwise to decrease the speaker volume or turn clockwise to increase the speaker volume When using the remote control press the VOL button to decrease the speaker volume or press VOL to increase the Speaker volume Muting the speakers Press the mute button on the device or the remote control to mute the speakers Press the mute button again to unmute the speakers MUTE will appear on the display when the speakers are muted Selecting the input source Press the mode button on the device or the function button on the remote control to select the desired input source The order of the input sources is Bluetooth AUX FM Radio SD Card amp USB Bluetooth mode Connecting with a Bluetooth device SN Put the device in Bluetooth mode If the device is in Bluetooth Pair mode press the pair button on the device or remote control When NS P lay the device is ready to pair with an external Bluetooth de
22. hen condensation may occur Do not use this device near water or other liquids Do not use this device in a damp room Do not use this device near a swimming pool Do not place objects that can create danger such as a candle or a glass of water on top of the device The display is made of plastic and might break when it s damaged Beware of sharp plastic splinters when the screen breaks to avoid injury Should the unit become wet immediately remove the plug from the power outlet and let the appliance fry for 72 hours before trying to use it again Hemove the batteries from the device and or remote control if they will not be used for a long time This device and the supplied accessories contain sensitive components Never drop them put them in a microwave burn them or paint them Do not bite or suck on the device and or supplied accessories Do not insert the device or the supplied accessories in your ears mouth or other body orifices This device and or accessories contain small parts that may lead to a choking hazard Therefore keep it away from children When connecting the device if a connector does not seem to fit do not force it Lenco recommends using A brand batteries Never expose the batteries to direct sunlight or extreme heat WARNING Prolonged exposure to loud sounds may lead to temporary or permanent hearing loss WARNING Do not use a USB extension cable to connect a USB device The use of a USB extension cabl
23. ion of the symbols This symbol indicates that there are important operating maintenance instructions in the user manual accompanying the device This symbol indicates that dangerous voltage is present within this device constituting a risk of electronic shock or personal injury This symbol indicates that the action in question may not be performed by a child because there is a risk of personal injury Important information before using the device Use the device only as described in the user manual Read the safety precautions carefully before use The safety precautions can be found in the back of the user manual If certain functions or instructions are unclear always contact our helpdesk or the dealer where the device was bought Information about our helpdesk can be found in the back of the manual This device is only intended for private use Information about the use and warranty can be found at the safety precautions and the information about service and support Never use this device in an explosive atmosphere gt gt gt gt gt Unpacking the device 5 The operations in this chapter should not be performed by children Get ready a knife or a pair of scissors 1 Cut the tape 2 Open the box e5 e 3 Lift the device from the box and remove the foam What to do with the packaging material Lenco recommends to keep the box and foam in case the product needs transporting in the future o
24. nes Press the TONE button on the remote control to adjust the audio settings Ater pressing once BASS will appear on the display Bass are the low tones Press the vol button on the remote control to enhance the bass tones Press the vol button on the remote control to reduce the bass tones Press the TONE button on the remote control to confirm the bass settings Now TREB appears on the display Treble are the high tones Press the vol button on the remote control to enhance the treble tones Press the vol button on the remote control to reduce the high tones Press the TONE button on the remote control to confirm the treble settings Resetting the device When the device is not responding or is not responding correctly reset the device by putting the power switch on the back of the device in the off position Then wait at least 5 minutes before switching on the device again If the device still does not work properly after the reset please consult the section troubleshooting contact your dealer or contact the Lenco helpdesk Maintenance 1 Clean the device only with a soft damp cloth 2 No part of this product requires maintenance Breaking down the device 49 The operations in this chapter should not be performed by children Before breaking down the device make sure the main power switch on the back of the device is in the OFF position If you have trouble locating this switch please consult the section Expl
25. ntrol to save the frequency Recalling a preset station Press the M and M buttons on the remote control to tune to a desired preset station Alternatively you can also enter the number by using the numeric buttons on the remote control Switching between mono and stereo Press the MO ST button to switch between mono and stereo FM reception If the Station being listened to has a weak signal some hiss may be audible It is possible to reduce this hiss by forcing the radio to play the station in mono rather than stereo SD Card mode Put the device in SD Card mode and insert the SD memory card The device will start reading the SD card Once the SD card is read the device will automatically start playing the files on the card Pausing playback During playback press the play pause knop on the device or the remote control to pause playback press the button once more to resume playback Skipping to the next track During playback of an audio file press the next button on the device or the remote control to skip to the next track Searching forward During the playback of an audio file hold the next button on the device or the remote control The device will search forward in the track until the button is released Skipping to the next track During playback of an audio file press the previous button on the device or the remote control to skip to the previous track Searching backward During the playback of an audio file hol
26. oring the device number 17 to see where this switch can be found 4 Do not touch the metal parts of the power cable because there is a risk of shocks with personal injury Get ready Phillips screwdriver 1 Disconnect the equipment that is connected to the AUX input and remove any USB devices and SD cards 2 Turn the main power switch on the back of the device in the off position 3 Remove the plug from the outlet and disconnect the power cord from the device Legend not included 4 Disconnect the wire antenna 5 Put the device on a flat stable surface that is slightly elevated for instance on a table so that the base can easily be removed Loosen the 4 screws and don t forget to hold the base so it can t fall down Storing and transporting the device 5 The operations in this chapter should not be performed by children Get ready Wide sturdy tape and the packaging material as saved according to the unpacking instructions 1 Insert the foam and lower the device into the box 2 Close the box shut 3 Tape the box shut Q5 Q5 The device is now ready to be stored or transported Try to limit the number of shocks as much as possible during transport Legend not included Reorder accessories Spare parts and accessories for this product can be ordered via your dealer or http lencosupport zendesk com The warranty terms on reordered accessories differ from our general wa
27. ows connecting an external device Fail situation A situation in which the device does not respond or operate as Intended For instance when buttons do not respond or smoke starts coming out of the device Mono Mono means one and in sound engineering the term is used to indicate that all sound is distributed and output through a single channel Stereo Stereo generally refers to two channel sound recording and or output a recording that contains a simultaneous signal for two speakers as opposed to monaural sound which one contains one channel Humans naturally hear stereo sound With two ears humans can process two different signals left and right and because of this the human brain can get a certain degree of spaciousness in the sound perception This is stereo input source These are the various connectivity options that the device offers for external equipment Troubleshooting Problem Son Check if the plug is inserted firmly into the outlet Put the main switch on the back of the Make sure the power outlet is powered To save energy the device turns itself off if playback has stopped for 10 minutes Adjust the volume or disable the mute No sound or poor sound function The device does not respond or Remove the plug from the outlet for at responds poorly Settings or selections are suddenly There is a time limit for settings and Radio stations cannot be received or can Re position the wire antenn
28. r to store the device when it s not being used for a long time The other packaging materials can be disposed of according to the local regulations Please contact your local authorities Legend not included Mounting the base G The operations in this chapter should not be performed by children Get ready Phillips screwdriver Put the device on a flat stable surface that is slightly elevated for instance on a table so that the base can easily be mounted Place the base against the bottom of the device and secure it with the 4 included screws Legend not included Exploring the device The instructions below will briefly explain the functionality of the buttons and controls A detailed instruction can be found in the various chapters of this 45678910 1314 1516 manual 1 Play pause button press this button to pause or resume playback 2 Previous rewind button press this button to skip to the previous song hold the button to search backward in the track 3 Next fast forward button press this button to skip to the next track or hold the button to search forward in the track 4 Bluetooth status LED this LED will flash when the device is trying to setup a Bluetooth connection If a Bluetooth connection is active the LED is lit continuously If no Bluetooth connection is active the LED will not be lit pue EE 5 Remote control sensor this sensor receives remote control signals
29. recommended by STL Group B V STL Group B V accepts no liability for the reliability or compatibility of these products
30. rranty terms Always inform about the warranty terms before buying accessories to avoid future complications Available accessories Euro plug Remote control Glossary Bluetooth Bluetooth is an open standard for short distance wireless connections between devices Open standard an open norm or standard that is publicly available LED The word ed was originally an acronym for light emitting diode A led is an electronic component a semiconductor that emits light when electric power is sent through in the forward direction Sensor Machines use sensors to observe the surroundings or gather information to control processes LCD A liquid crystal display is a flat screen with low energy consumption USB stick A USB stick also memory stick or plugin memory is an external storage media that can be connected to a computer by means of a USB port A USB stick uses flash memory to store information USB port USB Universal Serial Bus is a standard for connecting peripherals to computers or other equipment Flash memory Flash memory is a non volatile form of external memory This technique makes It possible to write or erase in several parts of the memory using a single programming operation Flash memory is non volatile memory it retains data when power is turned off SD Card A Secure Digital card SD Card is a memory card that is built from flash memory AUX in Auxiliary in An input on an audio device that all
31. ry Card 999 Files 99 folders FAT16 32 Munata A2DP AVRCP Sleep timer Yes Others Repeat function Yes SD amp USB Yes SD amp USB Materials Control Panel Product specifications may change without prior notice Safety Precautions Explanation of the symbols This symbol indicates that there are important operating maintenance instructions in the user manual accompanying the device h This symbol indicates that dangerous voltage is present within this device constituting a risk of electronic shock or personal injury This symbol indicates that the action in question may not be performed by a child because there is a risk of personal injury CAREFULLY READ THE FOLLOWING SAFETY PRECAUTIONS BEFORE USE WARNING A RISK OF ELECTRIC SHOCK A DO NOT OPEN THIS DEVICE WARNING DO REMOVE ANY SCREWS OR OTHER COMPONENTS OF THE DEVICE TO PREVENT THE RISK OF ELECTRIC SHOCK Install and use the device only as described in the user manual Never remove the housing of this device Never place this device on top of other devices Use only the specified accessories and attachments specified by the manufacturer This device must be used in combination with a power supply as specified in the specification table If you are not sure of the type of power supply used in your home consult your power company Do not use loose or damaged cords and or plugs This device has a Class ll construction Devices with a
32. vice the Bluetooth LED will flash Find BTT 2 on the external device and connect with it Thanks to Pair amp Play there is no need to enter a password Pair amp Play allows you to pair a Bluetoothe device with a single press of a button and enjoy your favorite music right away important note Depending on the external Bluetooth device the instructions below might not work or might not work correctly This is not a malfunction of the Lenco device or the external Bluetooth device Playing an audio file Choose your favorite audio file on the external Bluetooth device and play it on the device You can press play on the device or the remote control to start playback of the audio file Pausing playback During playback press the play pause button on the device or the remote control to pause playback press the button again to resume playback Skipping to the next track During playback of an audio file press the next button on the device or the remote control to skip to the next track Searching forward During the playback of an audio file hold the next button on the device or the remote control The device will search forward in the track until the button is released Skipping to the previous track During playback of an audio file press the previous button on the device or the remote control to skip to the previous track Searching backward During the playback of an audio file hold the previous button on the devic
33. works in radio mode Use this button to save a preset station or recall a preset station 18 Pair button if the device is in Bluetooth mode press this button to reconnect to another device Jobs O00 L UC 0101010 YODOG 19 PTY button only works in radio mode Press this button to select the desired program type 20 Ran button only works in SD amp USB mode Press this button to play tracks in a random order 21 MO ST button only works in radio mode Press this button to switch between FM mono and stereo audio 22 Tone button press this button to adjust the high and low tones 23 Volume button increase the volume press this button to Where to install y p 12 gt OO us H 0CO0CQ2CoQ OS S 7 E 16 a OOO O4 9 Sse 21 19 SD DD Sal 20 LO IIC CH LSO Never place the device in direct sunlight Place it on a sturdy platform of which the surface should be flat and steady so the product can t fall or hit by any objects Make sure the product is placed in such a manner that nothing can fall on top of it as pressure will damage or break the product Prevent insertion of objects into the ventilation slots or openings in the cabinet at all time Mounting the FM wire antenna 5 The operations in this chapter should not be performed by children The wire antenna can be found on the back of the device If you cannot find the wire antenna please check the section Exploring the
Download Pdf Manuals
Related Search