TREASURE COVE FORTUNE FINDER SCUBA MODEL 7000
Contents
1. TREASURE COVE FORTUNE FINDER SCUBA MODEL 7000 Features 00088 Preparation Assembly Battery installation Control Panel CONTENTS Power switch and SENS control c cccccceeeeeees seaeeeees serene DISC control LED amp Headset Operation DISG TUNCON sz 2s eae ots as Sf ts ee Se cca he ea ead apn cate Testing Correct Using Of The Search Coil Bide Ree ERAS nh Care and Maintenance FEATURES The TC 7000 Fortune Finder Scuba is a model with superb quality and performance It s not only highly sensitive but can distinguish the metal type also It can help user to find the lost coins gold silver jewelry and metal objects which can enable the users to have fun during operation Motion detection has relatively low requirements on environment Sensitivity adjustment function enables the detector easily adapted to different environment Discrimination adjustment function enables the elimination of unwanted metal Water proof detector and headset enable the underwater detection PREPARATION 1 Assembly Remove the stem and search coil assemblies from the shipping carton Unscrew the knob on top of the stem 1 and remove the knob connector Insert the stem and align the holes on the search coil bracket and the stem 1 Push the connector through the holes and tighten the k2. he power DISC control Counter clockwise rotate the switch to 0 and you can detector all kinds of metal Fully clockwise rotate the switch to eliminate most of the junk metal Different DISC degree is to be chosen according to different needs 3 LED amp Headset The LED flashes red when a target is detected closer the detector approaches to the target stronger the LED flashes The LED will flash red too when batteries need replacing When LED flashes red the headset will give out a sound of 400Hz TOO which indicates that the detector is approaching the target or the battery needs replacing OPERATION Clockwise rotate the SENS control to power on the detector 1 DISC function By adjusting the Discrimination control you will be able to ignore small pieces of metallic trash while detecting valuable targets Discrimination points are determined by such factors as size shape depth and type of metal and ground mineralization Scatter some sample targets such as coins pull tabs and small pieces of foil on the ground 1 to 2 feet apart 2 Turn the Sensitivity Control to clockwise full to set sensitivity to maximum 3 Turn the Discrimination control to counterclockwise full 4 Put the headset on and turn on the POWER Hold the search coil about 2 inches above and parallel to the ground Move it slowly over the samples and note the LED and Audio response as you pass over each one Keep in mind tha
3. lockwise rotating to increase the SENS generally rotate to the full to set the highest SENS High SENS should be used in the most detections 2 Counter clockwise rotate the switch to decrease the SENS Fully counter clockwise rotate the switch to turn off the power NOTES The environment will directly affect the detection result Through field detection you will master how to properly conduct the operation Some special circumstances are listed in below to give some hints how to detect and what to note when you detect in such environment 1 If there re 2 detectors operating at the same time in your detection area while they re also close to each other it ll lead to the mutual disturbance In this case you may decrease the SENS or keep the 2 detectors far away from each other 2 If there are interference from electrical cable or TV Radio station in your searching area lower the sensitivity or move away from the current searching area of disturbances 3 The proper SENS setting is very important when detecting in complex environment Sometimes a too high SENS will on the contrary lead to the non ideal detecting result because the soil mineralization and junk metals will both influence the signal which in turn affects the normal detection Thus you need to repeat the SENS adjustment to reach the best condition Only in most ideal environment can full SENS be set 4 The detection cannot be conducted if there re bulk metal near
4. nob Then remove the control box fixed on the upper stem 2 with arm support from the shipping carton Insert stem 1 into this upper stem 2 by snapping two spring locks on stem 1 into the proper holes on stem 2 User may adjust the stem length at will To extend the lower stem push in the spring lock pull out the lower stem and let the spring lock snap into another hole Wind the search coil cable around the stem make sure there is some slack then tighten the locknut Vat er proof headset Knob connect or Stem1 Stem2 Control house l Handie la Locknut Spring ock Search coi I a Cabl e Ar m support 2 Battery installation One piece of 9 Volt 6F22 battery is used to power this detector Set SENS on position ofPOWER OFF Tighten Accessor Use accessory to screw off the battery cover place a 9V battery into the battery compartment by matching the polarity symbols and marked on connector Reinstall the battery cover and tighten by the accessory Caution If you don t plan to use the unit for a week or more remove the batteries Batteries can leak chemicals that can destroy electronic parts s As CONTROLS PANEL 1 Illustration of control panel SENS control Power switch and Sensitivity control can be also used as power switch Fully counter clockwise rotate the switch to OFF to turn off the power Rotate it clockwise away from OFF to turn on t
5. ns will help you care for your metal detector so you can enjoy it for years carefully Dropping it can damage circuit boards and cases and can cause the detector to work improperly Use the detector only in normal temperature environments Temperature extremes can shorten the life of electronic devices damage the cases of the detector Keep the detector away from dust and dirt which can cause premature wear of parts Wipe the detector with a damp cloth occasionally to keep it looking new Do not use harsh chemicals cleaning solvents or strong detergents to clean the detector
6. t TC 7000 is a motion detector and responds only when the search coil is moving 5 Turn the Discrimination Control clockwise to several points of the white region and again pass over the targets Repeat this process at yellow region and so on to the red region You will note that as you change discrimination TC 7000 will reject some targets and continue to respond to others You can determine the discrimination points per your needs For example the small nail discrimination may be at some point of the yellow region and the pull tab discrimination point at red region 6 Some objects such as shallow bottle caps bent pull tabs or trash less than 2 inches from the coil may be difficult to reject The headset will give out a broken signal that will usually disappear if the search coil is raised slightly The strong signal of a good target will just get weaker too when the coil is raised 7 TC 7000 will remain silent when some objects are rejected however other objects may snap crackle and pop as they are rejected This is normal responses indicating that the powerful discrimination circuitry is doing its job 6 8 Large pieces of trash such as beer cans or jar lids may sound like good targets no matter what you do With a little practice however you will be able to tell the difference between a large target and a small coin sized object 2 SENS function 1 Clockwise rotate the switch to turn on the power go on c
7. the object metal since the signal form the bulk metal may exceed the one from the valued object metal In this case you have to remove this bulk metal or give up detection in this searching area may oo TESTING also applicable underwater 1 Turn on the power 2 Set SENS amp DISC control on proper position 3 Find a place without metal object 4 Place the object metal you want to search on the ground as the sample 5 Keep the search coil 1 2 inches from the ground move the coil back and forth on above the sample to observe the reaction Note Please mark the place where to put the metal object in case of loss CORRECT USING OF THE SEARCH COIL 1 Do not sway the search coil like a pendulum or the lifted side of the search coil will lead to the wrong readings Correct fa gt c ITT a T 2 Sweep your search coil as following picture move the search coil right and left in an arc line For not missing any target it is better to keep the distance from search coil to the ground about 1 2 inches closer to the earth for smaller target and the distance between two neighboring arcs is about 15 20cm Please move slowly and it should be parallel between the arc lines in case the object can be missing 8 Handle the detector gently and CARE AND MAINTENANCE Your TC 7000 Fortune Finder Scuba is an example of superior design and craftsmanship The following suggestio
Download Pdf Manuals
Related Search