PE2-10R-32 Manual
Contents
1. For Technical Support and Warranty Service Please Call 888 876 5387 Or Write To Soleus International Inc 20035 E Walnut Dr North City of Industry CA 91789 USA www soleusair com 162. SOLEUSAIPR 10 000 BTU Portable Air Conditioner with dehumidifier amp Fan PE2 10R 32 Operating Instructions lb Intertek 3046364 Model No PE2 10H 32 2010 Soleus Air International Thank you for choosing a Soleus Air Portable Air Conditioner This owner s manual will provide you with valuable information necessary for the proper care and maintenance of your new product Please take a few moments to thoroughly read the instructions and familiarize yourself with all the operational aspects of your new Soleus Air Portable Air Conditioner For your own records please attach a copy of your sales receipt to this manual Also write the store name location date purchased and serial number below Store Name Location Date Purchased serial Number located on back of unit IMPORTANT INSTRUCTIONS Before installing and using your portable air conditioner please read this owner s manual carefully Store this manual in a safe place for future reference Always place the unit on a level surface 2 Never use or store gasoline or other flammable vapor or liquid near this unit unless instructed by this manual 3 Maintain at least 10 inches 25 em clearance space around this unit Do not block or cover air inlet or outlet grilles 4 Theunit must be connected to a correctly grounded power supply 5 Do not start or stop the unit by inserting or pulling out the power plug 6 Do not use an ada
3. 4 5 6 7 Power On and Off Press the POWER button once to manually turn the unit on Press the POWER button once more to turn the unit off Mode Selection Press the MODE Button repeatedly to cycle between the different modes Auto mode Air Conditioner Dehumidifier and Fan Fan Speed Control Press the FAN SPEED Button to cycle through the different fan speeds High Medium and low The fan speed can be visually distinguished by the speed of the digital air segments progressing out from the windmill fan image on the Multi color display Temperature Select the desired temperature by pressing either V or A button when using the unit in cooling mode The temperature indicator flashes to display the desired temperature setting After the tem perature is set the unit will display this temperature setting until it is changed by the user The Multi color display shows temperature in Celsius or Fahrenheit Press the V or A buttons simultaneously on the con trol panel to select the desired temperature setting Timer Turn the unit on To program the unit to automatically turn on press the TIMER button when the unit is off Once the TIMER button is pressed the Timer On icon will flash in the multi color display Choose the preferred time for the unit to turn on between 1 24 hours by pressing the V or A buttons Once you have chosen the desired time the Timer On icon will flash for 3 seconds then remain lit until the uni
4. Fan Mode 1 Plug the Power Cord into an electrical outlet 2 Turn on the unit by pressing the POWER button on the control panel 3 Press the MODE button until the icon appears on the control panel display 4 Select the fan speed by pressing the FAN SPEED button 5 To circulate more air press the SWING button on the remote control The louvers will oscillate in our exclusive WAVEFLOO pattern back and forth and up and down spreading more air throughout the room NOTE It is not necessary for the exhaust hose and window kit to be installed to operate the unit in fan mode Auto Mode 1 Install the exhaust hoses and window kit properly see pages 7 amp 8 2 Plug the Power Cord into an electrical outlet 3 Turn on the unit by pressing the POWER button on the control panel 4 4 Press the MODE button until the x icon appears on the control panel display Select the fan speed by pressing the FAN SPEED button NOTE During AUTO mode the unit operates in Dehumidifier mode when the room temperature is between 68 F to 80 F The unit will operate in Air Conditioner mode when the room temperature 1s above 80 F In Auto mode the fan speed cannot be manually changed Sleep Mode This mode can only be selected when using the Remote control 1 To set Sleep mode make sure the unit is in Air Conditioner mode 2 Press the SLEEP Button on the remote control The icon appears on the control panel display 3 When in SLE
5. Wash the air filter by immersing it gently into warm water with a neutral detergent Rinse the filter and dry it thoroughly out of sunlight 3 Slide the filter back into the filter compartment after it is thoroughly dried 4 Ifthe filter is torn or unusable order a new filter by calling the customer service number on the warranty page of this manual Clean the unit Housing 1 Keep the unit from being exposed directly to the sun to prevent color fading 2 Clean the surface with a damp cloth and dry it with a soft towel storing the Unit for an Extended Period of Time or Transporting the unit 1 Empty any excess water by unplugging the water drainage stop the back of the unit located at the bottom 2 Unplug the unit 3 The unit should be stored in a cool dry place 15 22 WARRANTY One Year Limited Warranty Soleus International Inc warrants the accompanying Soleus Air PE2 10R 32 Portable Air Conditioner to be free of de fects in material and workmanship for the applications specified in its operation instruction for a period of ONE 1 year from the date of original retail purchase in the United States If the unit exhibits a defect in normal use Soleus International Inc will at its option either repair or replace it free of charge within a reasonable time after the unit 1s returned during the warranty period As a condition to any warranty service obligation the consumer must present this Warranty Certificat
6. Exhaust stretches from 14 1 4 to 60 5 8 Adapter 36cm to 150cm Exhaust Hose 1 Exhaust Hose Insulated Sleeve not pictured Adjustable window slider kit 2 piece set adjusts 28 5 to 55 p Drain tube amp Pan Adjustable Window Slider Kit INSTALLATION SELECTING THE LOCATION Place the unit in a flat location where the air out lets are not obstructed Place the unit at least 20 50cm away from a wall or other obstacle MOUNTING THE EXHAUST HOSE Slide the square end of the exhaust duct over the hot air outlet on the back of the unit The exhaust hose should be kept as short and straight as possible Prevent any sharp bends in the exhaust hose as this will trap hot exhaust air The hot exhaust air can be vented through the wall or out a window If mounting in the wall the height of the hole should be 16 to 50 inches 40cm to 130cm Soleus Air does not provide a venting kit for through the wall ventilation Venting through the wall requires a custom installation WINDOW KIT INSTALLATION HORIZONTAL WINDOW WINDOW KIT INSTALLATION The window kit is designed to fit into most standard vertical and horizontal windows as well as some sliding glass doors However it may be necessary to modify some aspects of the installation process for certain window types Open the window or sliding door and adjust the length of the window kit to fit the opening If the window
7. DEL PEZ10R32 Cooling Capacity 10 000 BTU Hr Dehumidifying Capacity 55ptslday 55ptslday Power Consumption 1050 W Air Flow Volume 225 CFM 115 V 60 HZ Sound Pressure Level 45 dB A Weight 65 6 lbs Dimensions WxDxH 12 98 x 22 17 x 27 78 Refrigerant R 410A DISCLAIMER ALL INFORMATION AND THE TECHNICAL SPECIFICATIONS PRESENTED IN THIS USER S MANUAL ARE THE PRESENTATION OF THE MANUFACTURER SOLEUS INTERNATIONAL HAS NOT CONDUCTED INDEPENDENT TEST TO THE INFORMATION AND THE SPECIFICATIONS PRESENTED HEREWITHIN SSS LCDI POWER CORD AND PLUG This air conditioner 15 equipped with an LCDI Leakage Current Detection and Interruption power cord plug as required by US National Electric Code 440 65 This cord consists of a length of shielded flexible cord with no termination on the load side and a LCDI attachment plug on the line side The LCDI power cord and plug will remove the supply source via electrical disconnect circuit trip 1f the nominal current leakage between the cord shield and either load conductor exceeds a predetermined value The cord will remain de energized until the devise has been manually reset This 1s intended to reduce the risk of a fire in the power cord or combustible materials nearby The cord shields are not grounded and they must be considered a shock hazards if exposed The cord shield must not be connected to ground or to any exposed metal The tes
8. EP mode the fan will run on low to keep fan noise at a minimum 4 When in Air Conditioner mode the temperature setting will gradually increase to 2 F above the original set temperature for 6 hours After 6 hours the temperature setting will return to the set temperature 5 When in Dehumidifier mode the temperature will not change when Sleep mode is selected Compressor Indicator ut icon will light up on the control panel display when the compressor turns on icon will turn off when the compressor shuts off 12 Emergency Condensate Holding Tank When the room temperature is low and the indoor humidity is high the air conditioner may not be able to evaporate some of the moisture fast enough When this happens the water will accumulate in an emergency condensate tank inside the unit Once the emergency condensate tank is full the unit will automatically shut off and will appear on the control panel display To empty condensate tank unscrew screw plug at the bottom back of the unit You will need a small pan approximately 1 high to catch the water com ing out of the condensate tank Once the condensate tank 1s drained the unit will begin working within a few minutes The emergency condensate tank holds approximately 1 5 Liters of water Another option is to pur chase a small hose from a hardware store that can fit around the 5 8 drain plug on the back of the unit and drain the
9. e along with a copy of the original purchase invoice THIS WARRANTY DOES NOT COVER e Damage accidental or otherwise to the unit while in the possession of a consumer not caused by a defect in material or workmanship e Damage caused by consumer misuse tampering or failure to follow the care and special handling provisions in the instructions e Damage to the finish of the case or other appearance parts caused by wear e Damage caused by repairs or alterations of the unit by anyone other than those authorized by Soleus Interna tional Inc e Freight and Insurance cost for the warranty service ALL WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANT ABILITY ARE LIMITED TO ONE YEAR DURATION OF THIS EXPRESS LIMITED WARRANTY SOLEUS INTERNATIONAL INC DISCLAIMS ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES AND IN NO EVENT SHALL SOLEUS INTERNATIONAL INC S LIABILITY EXCEED THE RETAIL VALUE OF THE UNIT FOR BREACH OF ANY WRITTEN OR IMPLIED WARRANTY WITH RESPECT TO THIS UNIT This warranty covers only new products purchased from our authorized dealers or retailers It does not cover used sal vaged or refurbished products As some states do not allow the limitation or exclusion of incidental or consequential damages or do not allow limitation on implied warranties the above limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights that vary from state to state
10. kit is not long enough connect the extra Window Slider Kit window kit panel to fit the opening Mark and cut Minimum 28 5 down a single panel of the window kit if neces Maximum 55 sary Place the window kit between the window and the window frame as shown in the images to the right Close the window onto the window kit to form a tight seal VERTICAL WINDOW Attach the exhaust duct adapter to the window kit Tabs located on the adapter will lock into place securing the adapter to the window kit Window Slider Kit Minimum 28 5 Maximum 55 WINDOW KIT INSTALLATION cont d e Installation of the Venting Kit a FOR SINGLE HOSE PORTABLE AIR CONDITIONERS The venting kit must be installed in order for the unit to work correctly in the air conditioning mode The venting kit should not be used while the unit is heating or fanning The window kit has been designed to fit into most vertical and horizontal window openings The window kit can also be used in a sliding door 1 Choose a suitable location near a grounded electrical outlet and a suitable window or door Remove packaging and locate components figure a 2 Slide the exhaust connector over the discharge opening on the back of the unit figure b 3 Connect the exhaust hose to the exhaust connector aligning the fitted arove figure c 4 Open the window or door and adjust the length of the window kit to fit the opening figure d If
11. lti color display 5 Press the A or V buttons until the desired room temperature appears on the control panel display The temperature ranges from 61 F 88 16 Cesi 6 Select desired fan speed by pressing the FAN SPEED button NOTE During hot days the unit will cool the room most efficiently by setting the temperature at the lowest setting and the fan speed on high Reducing the length of the exhaust duct insulating the exhaust hose and window kit and keeping direct sunlight to a minimum will also improve the cooling efficiency NOTE When the unit is running on cooling mode the exhaust hose is required and must be vented outside using the supplied window kit Dehumidifier Mode 1 Install the exhaust hoses and window kit properly see pages 7 amp 8 2 Plug the Power Cord into an electrical outlet 3 Turn on the unit by pressing the POWER Button on the control panel 4 Press the MODE button until the appears on control panel display NOTE The unit operates at low fan speed during dehumidifier mode The unit cools room slightly during the dehumidification Keep the windows and doors closed to aid the effectiveness of the unit 1n removing the moisture from the room NOTE When the unit is running in dehumidifier mode the exhaust hose is required and must be vented outside using the supplied window kit NOTE The unit will not perform in dehumidifier mode when the room temperature 15 lower than 61 F
12. necessary mark the kit and cut one end down to properly fit the opening figures e amp f 5 Attach the window kit adapter to the window kit figure g 6 Place the window kit back into the window and attach the exhaust hose to the window kit adapter figures h amp i Close the window tightly figure j Your Portable Air Conditioner is now ready to cool NOTE When using the venting system keep the exhaust hose as straight as possible The exhaust hose can be shortened but it is not recommended to increase the length of the exhaust hose Do not use an extension cord with your portable air conditioner NOTE The Portable Air Conditioner above may differ from the unit described in this manual The above directions and images show general directions for all Soleus Air single hose portable air conditioners The heating function is not available on this unit CONTROL PANEL DISPLAY amp OPERATING INSTRUCTIONS MODE BUTTON CONTROL PANEL amp MULTI COLOR DISPLAY FAN SPEED FAM SPEED SWING TIMER A UH TET 8 it T IE SWING BUTTO TIMER BUTTON INCREASE TEMP amp TIMER POWER BUTTON DECREASE TEMP amp TIMER MULTI COLOR DISPLAY AUTO A C DEHUM FAN TIMER ON TIMER OFF FAN SPEED TEMP AND TIMER INDICATOR SLEEP MODE ON OFF OSCILLATION ON OFF COMPRESSOR ON OFF BUCKET FULL OPERATING INSTRUCTIONS CONTROL PANEL BUTTONS Refer to the images on page 9 1 2 3
13. pter plug or extension cord 7 Do not use the unit in the immediate surroundings of a bath a shower or a swimming pool 8 Do not insert anything into the air outlet Do not obstruct air inlet or outlet grills unless instructed by this manual 9 Do not let children play near this unit 10 Always inspect the cord for signs of damage before use If the power cord is damaged it must be replaced by the manufacturer or a qualified service technician 11 When cleaning the unit always turn the unit off and unplug the power cord 12 When the unit is not in use always remove the venting kit from the window PACKAGE CONTENTS Portable Air Conditioner Exhaust Hoses 1 Hose Adapters 1 Window Kit Adapter 1 Remote Control AAA Batteries 2 Window Kit 2 Sliding Panels 1 single hose panel 1 extension panels Owner s Manual EE BA NM SPECIFICATIONS e The cooling capacity is measured at an ambient temperature of DB 86 F WB 78 F e Noise level is measured at a distance of 3 28 ft away from front of the unit when the unit is in cooling mode e Power consumption is measured when the fan runs at the highest speed setting e These specifications are for reference only For actual data please refer to the rating label on the back of the unit e Ifthe environment temperature is higher than max operating temperature or lower than the minimum operating temperature the air conditioner may not work properly MO
14. t and reset buttons on the LCDI Plug are used to check 1f the plug 1s functioning properly To test 1 Plug power cord into wall outlet 2 Press TEST Button circuit should trip cutting power to the air conditioner 3 Press RESET button for use If a test is performed and the indicator light remains ON current leakage has been detected Do not use the air conditioner or attempt to reset the LCDI Plug Contact Soleus Air Customer Service for troubleshooting recommendations RESET TEST WARNING 1 DO NOT press the TEST button while the air conditioner is operating 2 The TEST and RESET buttons should not be used as ON and OFF switches 3 The cord and plug are not intended to offer protection to externally connected loads or supply circuits 4 The cord and plug are intended for indoor use only PRODUCT DIAGRAM Actual product design may differ slightly from images below FRONT A A Control panel foc STITT B Vertical air louvers 59 wm C Air outlet mm D Horizontal air louvers E E Casters F Power Cord amp Plug a E Nt e AU BACK t oe N T Hot air outlet grill EN T ZA B Lower air inlet grill CEEA EEEE N 22 E B ZE HO 2 a i N ACCESSORIES Drain tube 7 Drainpan Flexible exhaust hose with 2 adapters i dd 3 piece 3 8 screw ipe Window
15. t turns on Timer Turn the unit off To program the unit to automatically turn off press the TIMER button when the unit 15 on Once the TIMER button is pressed the Timer Off icon on the display on the unit will flash lt Qe Press the A or V buttons to change the clock to the desired time for the unit to automatically turn off The TIMER indicator will flash for 3 seconds to activate your programmed time then remain solid until the unit automatically shuts down Swing To start horizontal oscillation press the Swing button once 9 icon will appear on the multi color display To stop oscillation press the Swing button again Vertical air flow direction can be adjusted manually NOTE The timer will remember your settings when it is set If you set the timer while in Air Conditioning mode the timer will automatically turn the unit on and off in air conditioning mode according to the desired programmed times The timer will also remember the temperature settings fan speed and oscillation setting The timer works when the unit is in Air Conditioner mode Dehumidifier mode Fan mode and Auto mode 10 OPERATING THE UNIT USING THE CONTROL PANEL Air Conditioner Mode 1 Install the exhaust hose and window kit properly see pages 7 amp 8 2 Plug the Power Cord into an electrical outlet 3 Turn on the unit by pressing the POWER button on the control panel 4 Press the Mode button until the icon appears on the Mu
16. the A or V to select your desired temperature setting The temperature on the multi color display on the control panel will increase or decrease accordingly Pressing the F C button will change the temperature select between F and C 5 Sleep Mode See SLEEP MODE on page 12 6 Swing To turn on oscillation press the SWING button on the remote control Once you press SWING the louvers on the unit will oscillate back and forth 7 Timer To program the unit to turn on press the TIMER button on the remote control when the unit is OFF Press the A or V buttons to change the clock to the desired time for the unit to automatically turn on Timer On indicator on the display will flash for 3 seconds to activate your programmed Turn On time To program the unit to turn off press the TIMER button when the unit is ON and press the A or V buttons to change the clock to the desired time for the unit to automatically turn off The Timer Off indi cator on the display will flash for 3 seconds to activate your programmed Shut Down time 14 MAINTENANCE Note Make sure power 1s off and the power cord is not plugged into an electrical outlet prior to performing any maintenance on the unit Clean or replace filter If the air filter 1s blocked with a dust the airflow volume may reduce It 1s recommended to clean the filter once every two weeks or as needed 1 Remove the filter from the filter compartment on the back of the unit 2
17. unit into a gravity drain or larger pan for continuous drainage To resume operation quickly empty the water container according to the following steps 1 Turn the unit off Do not move the unit when the water container is full 2 Place the drain pan accessory under the drainage port at the back of the unit 3 Remove the screw plug from the drain hole The condensate water will drain out automatically When the drain pan is full screw the screw plug back onto the drainage hole to stop the water flow Empty the drain pan Repeat until all the water 1s emptied Once the water container has been emptied screw the plug back onto the drain hole Do not allow the water to drip continuously into the drain pan as it might easily overflow 13 OPERATING THE UNIT USING THE REMOTE CONTROL REMOTE CONTROL TIMER TEMP INCREASE SWING LOUVER MODE BUTTON OSCILLATION C F BUTTON FAN SPEED TIMER BUTTON SLEEP MODE TIMER TEMP DECREASE POWER BUTTON REMOTE CONTROL OPERATING INSTRUCTIONS 1 Power On and Off Press the ON OFF button on the remote to turn the unit on or off 2 Mode Selection Press the MODE Button repeatedly to cycle between the different modes Auto Air Conditioner Dehumidifier and Fan only mode 3 Fan Speed Press the FAN button to cycle through low medium and high fan speeds 4 Temperature Setting When the unit is in Air Conditioner mode you can select your desired tempera ture Press
Download Pdf Manuals
Related Search